Influence of Surface Properties on Adhesion Forces and Attachment of Streptococcus mutans to Zirconia In Vitro

Biological Effects of Double-Layered Hydroxyapatite and Zirconium Oxide Depositions on Titanium Surfaces

Purpose

This study aimed to confirm the synergy effect of these two materials by evaluating osteoblast and antibacterial activity by applying a double-layered hydroxyapatite(HA) zirconium oxide(ZrO2) coating to titanium.

Methods

The specimens used in this study were divided into four groups: a control group (polished titanium; group T) and three experimental groups: Group TH (RF magnetron sputtered HA deposited titanium), Group Z (ZrO2 ALD deposited titanium), and Group ZH (RF magnetron sputtered HA and ZrO2 ALD deposited titanium). The adhesion of Streptococcus mutans (S.mutans) to the surface was assessed using a crystal violet assay. The adhesion, proliferation, and differentiation of MC3T3-E1 cells, a mouse osteoblastic cell line, were assessed through a WST-8 assay and ALP assay.

Results

Group Z showed a decrease in the adhesion of S. mutans (p < 0.05) and an improvement in osteoblastic viability (p < 0.0083). Group TH and ZH showed a decrease in adhesion of S. mutans (p < 0.05) and an increase in osteoblastic cell proliferation and cell differentiation (p < 0.0083). Group ZH exhibited the highest antibacterial and osteoblastic differentiation.

Conclusion

In conclusion double-layered HA and ZrO2 deposited on titanium were shown to be more effective in inhibiting the adhesion of S. mutans, which induced biofilm formation, and increasing osteoblastic differentiation involved in osseointegration by the synergistic effect of the two materials.

Effect of postpolymerization time and atmosphere on surface properties and biofilm formation in additively manufactured resins for definitive restorations

OBJECTIVES

To investigate how postpolymerization time (PPT) and atmosphere (PPA) influence the surface properties, protein adsorption, and microbial adhesion of two types of additively manufactured (AM) resins used for definitive restorations.

METHODS

Two different types of commercially available AM resins for definitive restorations (UR and CR) were used to create disk-shaped specimens. These specimens were divided into eight groups based on resin type (UR and CR), PPT (standard or extended), and PPA (air or nitrogen). After postpolymerization, the surface roughness (Ra and Sa) and surface free energy (SFE) of all specimens were measured. The study also evaluated protein adsorption, microbial attachment, and cytotoxicity. A non-parametric factorial analysis of variance with post-hoc analyses was conducted, using a significance level (α) of 0.05.

RESULTS

The Ra and Sa values for CR were higher than those for UR, regardless of PPT or PPA (P < 0.05). For UR, SFE was higher with extended PPT compared to standard PPT. CR had higher SFE than UR under standard PPT. The interaction between PPT and PPA had a significant effect on protein adsorption (P < 0.05). When PPT was standard, nitrogen significantly increased protein adsorption compared to air. The interaction between resin type and PPA, and between resin type and PPT, significantly affected microbial adhesion (P < 0.05). The changes in PPT or PPA did not affect the cytotoxicity of either AM resin.

CONCLUSION

Surface properties, protein adsorption, and microbial attachment were influenced by the interactions among PPT, PPA, and resin type. These factors can have implications for resin-based definitive restorations.

CLINICAL SIGNIFICANCES

Clinicians should understand the impact of PPT and PPA on the surface properties of AM resins for definitive restorations, particularly regarding protein adsorption and microbial adhesion. Additionally, the type of AM resin (based on chemical composition) could affect its biological properties.

Does dental material type influence bacterial adhesion under the same polishing conditions? Direct observation using a fluorescent staining technique: An in vitro study

Highly polished 3, 4, and 5 mol% yttria-stabilized zirconia and CAD/CAM composite resin samples were prepared, and the influence of surface roughness (Ra and Sa, 21 areas/group), wettability (contact angle and surface energy, 3 samples/group), and surface chemical composition (2 samples/group) on single-strain bacterial adhesion models (Porphyromonas gingivalis, Streptococcus oralis, Streptococcus sanguinis, Streptococcus gordonii, and Streptococcus mutans) were compared via fluorescent staining with graphical analysis (21 areas/group). Statistical analysis was performed using the Shapiro-Wilk test followed by one-way analysis of variance with Tukey's test or the Kruskal-Wallis test with Dunn's test (α=0.05) and linear regression. For dental zirconia with the same surface roughness, the yttria content did not significantly influence the initial bacterial adhesion. However, higher bacterial adhesion was detected for the composite resin owing to its high C, O, and Si contents. There was no correlation between surface energy and bacterial adhesion for any bacterial strain (p<0.005).

Injectable and Microporous Microgel-Fiber Granular Hydrogel Loaded with Bioglass and siRNA for Promoting Diabetic Wound Healing

Injectable hydrogels find extensive application in the treatment of diabetic wound healing. However, traditional bulk hydrogels are significantly limited due to their nano-porous structure, which obstructs cell migration and tissue infiltration. Moreover, regulating inflammation and matrix metalloproteinase -9 (MMP-9) expression in diabetic wounds is crucial for enhancing wound healing. This study marks the first instance of introducing an efficient, scalable, and simple method for producing microfiber-gel granules encapsulating bioceramics powders. Utilizing this method, an injectable microporous granular microgel-fiber hydrogel (MFgel) is successfully developed by assembling microgel-fibers made from hyaluronic acid (HA) and sodium alginate (SA) loaded with small interfering RNA (siRNA) and bioglass (BG) particles. Compared to traditional hydrogels (Tgel), MFgel possesses a highly interconnected network with micron-sized pores, demonstrating favorable properties for cell adhesion and penetration in in vitro experiments. Additionally, MFgel exhibits a higher compressive modulus and superior mechanical stability. When implanted subcutaneously in mice, MFgel promotes cellular and tissue infiltration, facilitating cell proliferation. Furthermore, when applied to skin defects in diabetic rats, MFgel not only effectively regulates inflammation and suppresses MMP-9 expression but also enhances angiogenesis and collagen deposition, thereby significantly accelerating diabetic wound healing. Taken together, this hydrogel possesses great potential in diabetic wound healing applications.

Effects of various beverages on characteristics of provisional restoration materials

OBJECTIVE

To investigate the effect of common beverages on four currently used provisional restoration materials: Protemp®4, Integrity®, polymethyl methacrylate (PMMA) block, and acrylic resin. Flowable resin composite is included as a control group.

MATERIALS AND METHODS

Each material was formed into disks of 10-mm diameter and 4-mm thickness (N = 40) by loading the material into acrylic molds. The exposed surface in the mold was covered using a glass slide to prevent an oxygen inhibition layer, and polymerization then proceeded. The solidified disks were placed in distilled water for 24 h. These samples (n = 8) were then immersed for 14 days in one of four different beverages: water, orange juice, cola, and coffee. Changes in color dimension, hardness, and roughness were observed and then analyzed using two-way repeated analysis of variance.

RESULTS

The provisional materials had more obvious changes in all three color dimensions than the flowable resin composite. Integrity showed the biggest changes, followed by acrylic resin and PMMA block, whereas Protemp had the smallest changes. The hardness of all the materials significantly decreased after immersion in any of the beverages for 14 days. There were no changes in surface roughness when the materials were immersed in distilled water. The surface roughness of the PMMA block significantly decreased in orange juice whereas that of Integrity and acrylic resin significantly increased in cola.

CONCLUSION

Different kinds of provisional materials had different degrees of staining due to their composition. Moisture had a significant influence on the hardness of materials, and the acidity of cola significantly roughened the surface of the provisional materials.

Initial bacterial adherence and biofilm formation on novel restorative materials used in paediatric dentistry

OBJECTIVE

To evaluate the initial bacterial adherence and biofilm formation on novel restorative materials in paediatric dentistry and compare the results to stainless steel crown and primary enamel.

MATERIALS AND METHODS

Twenty-five samples (Diameter = 4 mm) from five restorative materials (Tetric Power Fill light cured for 3 s or 10 s, Fuji II LC, Equia Forte HT Fil, Cention Forte, Stainless-steel crown) and primary enamel were prepared. Four samples served for recording of surface roughness (Ra) using a contact profilometer, 21 samples were incubated in stimulated human saliva for 2 h (initial bacterial adherence) and 72 h (biofilm formation) and served to determine ion releasing and bacterial growth. After 2 and 72 h, the number of colony-forming units (CFU) per ml was counted and expressed in Log10 CFU/ml. Data were analysed with two-way ANOVA and Tuckey's multiple comparisons test (p < 0.05).

RESULTS

All tested materials showed similar initial bacterial adherence (p > 0.1). Stainless steel crown showed statistically significantly less biofilm formation than all other tested materials (p ≤ 0.02), except for Fuji II LC (p = 0.06). In terms of biofilm formation, the differences between all tested materials were not statistically significant (p ≥ 0.9).

SIGNIFICANCE

Novel restorative materials in paediatric dentistry show similar initial bacterial adherence and biofilm formation. However, compared to other restorative materials, stainless steel crowns demonstrate the lowest level of biofilm formation. Ion-releasing materials may not necessarily show better antimicrobial properties than conventional materials.

Synthesis and Characterization of Durable Antibiofilm and Antiviral Silane-Phosphonium Thin Coatings for Medical and Agricultural Applications

Pathogens such as bacteria and viruses cause disease in a range of hosts, from humans to plants. Bacterial biofilms, communities of bacteria, e.g., Staphylococcus aureusand Escherichia coli, attached to the surface, create a protective layer that enhances their survival in harsh environments and resistance to antibiotics and the host's immune system. Biofilms are commonly associated with food spoilage and chronic infections, posing challenges for treatment and prevention. Tomato brown rugose fruit virus (ToBRFV), a newly discovered tobamovirus, infects tomato plants, causing unique symptoms on the fruit, posing a risk for tomato production. The present study focuses on the effectiveness of silane-phosphonium thin coatings on polymeric films, e.g., polypropylene. Phosphonium has significant antibacterial activity and is less susceptible to antibacterial resistance, making it a safer alternative with a reduced environmental impact. We successfully synthesized silane-phosphonium monomers as confirmed by 31P NMR and mass spectrometry. The chemical composition, thickness, morphology, and wetting properties of the coatings were tested by Fourier-transform infrared spectroscopy with attenuated total reflectance, focused ion beam, atomic force microscopy, environmental scanning electron microscope, and contact angle (CA) measurements. The antibiofilm and antibacterial activities of the coatings were tested against S. aureus and E. coli, while the antiviral activity was evaluated against ToBRFV. The significant antibiofilm and antiviral activity suggests applications in various fields including medicine, agriculture, and the food industry.

Food grade disinfectants based on hydrogen peroxide/peracetic acid and sodium hypochlorite interfere with the adhesion of Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Listeria monocytogenes to stainless steel of differing surface roughness

This study aimed to evaluate the potential of the bacterium Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Listeria monocytogenes to adhere to stainless steel discs with differing degrees of surface roughness (Ra = 25.20-961.90 nm). Stainless steel is a material commonly used in the food industry for processing equipment, which is regularly exposed to cleaning procedures. The investigation included the commercial disinfectants hydrogen peroxide/peracetic acid and sodium hypochlorite which were evaluated for their antibacterial and anti-adhesion activity. The adhesion was assessed by the standard plate count method, while the broth microdilution method CLSI M07-A10 was used to determine the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the disinfectants. Based on the MIC values, both disinfectants exerted significant inhibitory effects with MIC values for hydrogen peroxide/peracetic acid and sodium hypochlorite of 250 µg ml-1 and 500 µg ml-1, respectively. Whereas the MBC values were equal to the MIC for all bacteria except for E. coli with values 2-fold higher than the MIC. Obtained results also revealed that all tested bacteria were able to adhere to stainless steel surfaces, although differences were found for strains and surface roughness. The lowest adhesion rate of each strain was recorded on the roughest stainless steel disc at a Ra of 961.90 nm. Further, at a concentration of 1 MIC, the disinfectant sodium hypochlorite reduced initial bacterial adhesion to stainless steel surfaces to a significantly greater extent than the disinfectant hydrogen peroxide/peracetic acid. These findings are consistent with the results obtained by Scanning Electron Microscopy (SEM) analysis, which indicates the great applicability of the tested disinfectants for the control of bacterial adhesion in the food industry.

Nanomechanical changes in probiotic bacteria under antibiotics exposure: Implications on Lactobacillus biofilm formation

Recognition of the microbial cell's surface constituents' biophysical properties is an important research topic, allowing a better understanding of the cell's behaviour under different conditions. Atomic force microscopy (AFM) was employed in this study to analyse the basis of the nanomechanical changes in probiotic bacteria under nitrofurantoin, furazolidone, and nitrofurazone exposure. Recorded significant changes in the two Lactobacillus strains cells morphology, topography, and adhesion parameters resulted in the increase of the cells' longitude (up to 2.58 μm), profile height (by around 0.50 μm), and decrease in the adhesion force (up to 13.58 nN). Young's modulus and adhesion energy decreased within 96 h, however with no negative effect on the cells' morphology or loss of structural integrity. Observed modifications present the mode of action of the 5-nitrofuran derivative antibiotics on probiotic biofilm formation and suggest activation of the multilevel adaptation mechanisms to counteract unfavorable environments. A visual change in bacterial morphology such as an increased surface-to-volume ratio might be a link between molecular-level events and outcomes in individual cells and biofilms. This paper for the first time shows, that these antibiotics affect the properties of non-target microorganisms as lactobacilli, and might impair biofilm formation. However, the degree of such transformations depends on the delivered active substance.

Key topographic parameters driving surface adhesion of Porphyromonas gingivalis

Dental implant failure is primarily due to peri-implantitis, a consequence of bacterial biofilm formation. Bacterial adhesion is strongly linked to micro-/nano-topographies of a surface; thus an assessment of surface texture parameters is essential to understand bacterial adhesion. In this study, mirror polished titanium samples (Ti6Al4V) were irradiated with a femtosecond laser (fs-L) at a wavelength of 1030 nm (infrared) with variable laser parameters (laser beam polarization, number, spacing and organization of the impacts). Images of 3-D topographies were obtained by focal variation microscopy and analyzed with MountainsMap software to measure surface parameters. From bacteria associated with peri-implantitis, we selected Porphyromonas gingivalis to evaluate its adhesion on Ti6Al4V surfaces in an in vitro study. Correlations between various surface parameters and P. gingivalis adhesion were investigated. We discovered that Sa value, a common measure of surface roughness, was not sufficient in describing the complexity of these fs-L treated surfaces and their bacterial interaction. We found that Sku, density and mean depths of the furrows, were the most accurate parameters for this purpose. These results provide important information that could help anticipate the bacterial adhesive properties of a surface based on its topographic parameters, thus the development of promising laser designed biofunctional implants.

Understanding bacterial biofilms: From definition to treatment strategies

Bacterial biofilms are complex microbial communities encased in extracellular polymeric substances. Their formation is a multi-step process. Biofilms are a significant problem in treating bacterial infections and are one of the main reasons for the persistence of infections. They can exhibit increased resistance to classical antibiotics and cause disease through device-related and non-device (tissue) -associated infections, posing a severe threat to global health issues. Therefore, early detection and search for new and alternative treatments are essential for treating and suppressing biofilm-associated infections. In this paper, we systematically reviewed the formation of bacterial biofilms, associated infections, detection methods, and potential treatment strategies, aiming to provide researchers with the latest progress in the detection and treatment of bacterial biofilms.

Antimicrobial surface processing of polymethyl methacrylate denture base resin using a novel silica-based coating technology

OBJECTIVES

This study investigated the surface characteristics of denture base resin coatings prepared using a novel silica-based film containing hinokitiol and assessed the effect of this coating on Candida albicans adhesion and growth.

METHODS

Silica-based coating solutions (control solution; CS) and CS containing hinokitiol (CS-H) were prepared. C. albicans biofilm formed on denture base specimens coated with each solution and these uncoated specimens (control) were analyzed using colony-forming unit (CFU) assay, fluorescence microscopy, and scanning electron microscopy (SEM). Specimen surfaces were analyzed by measuring the surface roughness and wettability and with Fourier-transform infrared (FT-IR) and proton nuclear magnetic resonance (¹H NMR). Stability of coated specimens was assessed via immersion in water for 1 week for each group (control-1w, CS-1w, and CS-H-1w) followed by CFU assay, measurement of surface roughness and wettability, and FT-IR.

RESULTS

CS-H and CS-H-1w contained significantly lower CFUs than those present in the control and control-1w, which was also confirmed via SEM. Fluorescence microscopy from the CS-H group identified several dead cells. The values of surface roughness from coating groups were significantly less than those from the control and control-1w. The surface wettability from all coating groups exhibited high hydrophobicity. FT-IR analyses demonstrated that specimens were successfully coated, and ¹H NMR analyses showed that hinokitiol was incorporated inside CS-H.

CONCLUSIONS

A silica-based denture coating that incorporates hinokitiol inhibits C. albicans growth on denture.

CLINICAL RELEVANCE

We provide a novel antifungal denture coating which can be helpful for the treatment of denture stomatitis.

Potential of Advanced Oxidation as Pretreatment for Microplastics Biodegradation

In the last two decades, microplastics (MP) have been identified as an emerging environmental pollutant. Due to their small size, MP particles may easily enter the food chain, where they can have adverse effects on organisms and the environment in general. The common methods for the removal of pollutants from the environment are not fully effective in the elimination of MP; thus, it is necessary to find a more suitable treatment method(s). Among the various approaches tested, biodegradation is by far the most environmentally friendly and economically acceptable remediation approach. However, it has serious drawbacks, generally related to the rather low removal rate and often insufficient efficiency. Therefore, it would be beneficial to use some of the less economical but more efficient methods as pretreatment prior to biodegradation. Such pretreatment would primarily serve to increase the roughness and hydrophilicity of the surface of MP, making it more susceptible to bioassimilation. This review focuses on advanced oxidation processes (AOPs) as treatment methods that can enhance the biodegradation of MP particles. It considers MP particles of the six most commonly used plastic polymers, namely: polyethylene, polypropylene, polystyrene, polyvinyl chloride, polyethylene terephthalate and polyurethane. The review highlights organisms with a high potential for biodegradation of selected MP particles and presents the potential benefits that AOP pretreatment can provide for MP biodegradation.

Microbiome and the inflammatory pathway in peri-implant health and disease with an updated review on treatment strategies

Crestal bone preservation around the dental implant for aesthetic and functional success is widely researched and documented over a decade. Several etiological factors were put forth for crestal bone loss; of which biofilm plays a major role. Biofilm is formed by the colonization of wide spectra of bacteria inhabited around dental implants. Bacterial adherence affects the regulators of bone growth and an early intervention preserves the peri-implant bone. Primary modes of therapy stated in early literature were either prevention or treatment of infection caused by biofilm. This narrative review overviews the microbiome during different stages of peri-implant health, the mechanism of bone destruction, and the expression of the biomarkers at each stage. Microbial contamination and the associated biomarkers varied depending on the stage of peri-implant infection. The comprehensive review helps in formulating a research plan, both in diagnostics and treatment aspects in improving peri-implant health.

Biogenic nanosilver-fabricated endotracheal tube to prevent microbial colonization in a veterinary hospital

COVID-19 patients have often required prolonged endotracheal intubation, increasing the risk of developing ventilator-associated pneumonia (VAP). A preventive strategy is proposed based on an endotracheal tube (ETT) modified by the in situ deposition of eucalyptus-mediated synthesized silver nanoparticles (AgNPs). The surfaces of the modified ETT were embedded with AgNPs of approximately 28 nm and presented a nanoscale roughness. Energy dispersive X-ray spectroscopy confirmed the presence of silver on and inside the coated ETT, which exhibited excellent antimicrobial activity against Gram-positive and Gram-negative bacteria, and fungi, including multidrug-resistant clinical isolates. Inhibition of planktonic growth and microbial adhesion ranged from 99 to 99.999% without cytotoxic effects on mammalian cells. Kinetic studies showed that microbial adhesion to the coated surface was inhibited within 2 h. Cell viability in biofilms supplemented with human tracheal mucus was reduced by up to 95%. In a porcine VAP model, the AgNPs-coated ETT prevented adhesion of Pseudomonas aeruginosa and completely inhibited bacterial invasion of lung tissue. The potential antimicrobial efficacy and safety of the coated ETT were established in a randomized control trial involving 47 veterinary patients. The microbial burden was significantly lower on the surface of the AgNPs-coated ETT than on the uncoated ETT (p < 0.05). KEY POINTS: • Endotracheal tube surfaces were modified by coating with green-synthesized AgNPs • P. aeruginosa burden of endotracheal tube and lung was reduced in a porcine model • Effective antimicrobial activity and safety was demonstrated in a clinical trial.

Antibacterial Effect of Zirconia Nanoparticles on Polyethyl Methacrylate Resin for Provisional Crowns

Objective

Mid-to-long term use of provisional crowns in the oral cavity is associated with bacterial adhesion and biofilm formation, thus necessitating provisional crowns exhibiting antibacterial properties to prevent the occurrence of gingivitis and periodontal disease. This study aimed to evaluate the antibacterial effect of zirconia nanoparticle-containing polyethyl methacrylate (PEMA) resin for provisional restorations.

Methods

Zirconia nanoparticles were added to the monomer of PEMA resin for provisional restorations, and the mixture was stirred for 2 h using a magnetic stirrer. Disk-shaped specimens were prepared by mixing the polymer with the nanoparticle solution. The control group contained pure PEMA resin samples, and the experimental groups Group Z2, Group Z4, and Group Z8 included PEMA resin specimens containing 2, 4, and 8% w/v zirconia nanoparticles, respectively. After analyzing the sample surfaces, the antibacterial effect of the specimens was evaluated using Streptococcus mutans. Statistical analysis was performed using Tukey's test and Mann-Whitney U-test, according to the normality result in the Shapiro-Wilk test.

Results

FE-SEM and EDX analyses revealed the successful addition of zirconia nanoparticles. Results showed no significant difference in the measured values for surface roughness and contact angle between the experimental and control groups; however, adhesion and biofilm thickness of S. mutans were significantly decreased in Group Z2, Group Z4, and Group Z8 compared to the control group (P < 0.05, P < 0.01, P < 0.01, respectively).

Conclusion

The addition of zirconia nanoparticles can lower the incidence of adhesion and biofilm thickness of S. mutans on PEMA resin used for provisional crowns. Thus, incorporating zirconia nanoparticles in repair materials for provisional crowns and PEMA resin can produce an antibacterial effect and prevent gingivitis, periodontal disease, and dental caries.

Biological and Physicochemical Characterization of Self-Adhesive Protective Coating Dental Restorative Material after Incorporation of Antibacterial Nanoparticles

This study evaluated the physicochemical and antibacterial properties of EQUIATM coat liquid (E) after incorporation of zinc oxide (ZnO) and titanium dioxide (TiO2) nanoparticles. ZnO and TiO2 (1 wt.% and 2 wt.%) were dispersed in EQUIA coat. Principal component analysis (PCA) and cluster analysis were performed to visualize systemic variation. Antibacterial activity was evaluated by colony-forming units and crystal violet staining using Streptococcusmutans and Lactobacillusacidophilus after 24 h, 48 h, and 72 h, and the microstructure was studied by scanning electron microscopy. The weight change was analyzed at 1 and 21 days. The PCA for TiO2- and ZnO-based groups showed 100% variance at all spectral ranges at 600−800/cm and 800−1200/cm, whereas 1200−1800/cm and 2700−3800/cm spectral regions demonstrated 99% variance. The absorbance values were significant (p < 0.05) for both nanoparticles-based adhesives, and the specimens with 2 wt.% ZnO showed the maximum response by minimum bacterial attachment, and the control group showed the least response by maximum attachment. The weight change percentage was reduced after the incorporation of antibacterial nanoparticles. It is suggested that EQUIATM coat containing nanoparticles exhibits promising results, and it may be recommended to clinically use as an improved coating material.

Zirconia-based nanomaterials: recent developments in synthesis and applications

In the last decade, the whole scientific community has witnessed great advances and progress in the various fields of nanoscience. Among the different nanomaterials, zirconia nanomaterials have found numerous applications as nanocatalysts, nanosensors, adsorbents, etc. Additionally, their exceptional biomedical applications in dentistry and drug delivery, and interesting biological properties, viz. anti-microbial, antioxidant, and anti-cancer activity, have further motivated the researchers to explore their physico-chemical properties using different synthetic pathways. With such an interest in zirconia-based nanomaterials, the present review focuses systematically on different synthesis approaches and their impact on the structure, size, shape, and morphology of these nanomaterials. Broadly, there are two approaches, viz., chemical synthesis which includes hydrothermal, solvothermal, sol-gel, microwave, solution combustion, and co-precipitation methods, and a greener approach which employs bacteria, fungus, and plant parts for the preparation of zirconia nanoparticles. In this review article, the aforementioned methods have been critically analyzed for obtaining specific phases and shapes. The review also incorporates a detailed survey of the applications of zirconia-based nanomaterials. Furthermore, the influence of specific phases, morphology, and the comparison with their counterpart composites for different applications have also been included. Finally, the concluding remarks, prospects and possible scope are given in the last section.

The propensity of fomite spread of SARS-CoV-2 virus through produce supply chain

BACKGROUND

The global community has battled the spread of SAR-CoV-2 for almost 2 years, and the projection is that the virus may be recurrent like the seasonal flu. The SARS-CoV-2 pandemic disrupted activities within the food supply chain that cost billions of dollars globally. This has heightened concerns about fomite spread of the virus through surfaces. There is an urgent need to understand the risk portends by this virus along the produce supply chain with conditions (low temperature and high relative humidity) conducive to extended survival of the virus.

MAIN BODY

Pre-dating SARS-CoV-2 are other types of coronaviruses that had lower infection and mortality rates. There are some similarities between the former and the new coronavirus, especially with regards to transmission modes and their survivability on surfaces. There is evidence of other coronaviruses' survival on surfaces for weeks. Currently, there are limited evidence-based studies to enlighten us on how the virus is transmitted within the produce supply chain. A few studies claim that the virus could spread through the cold supply chains. However, these are not sufficient to make a conclusive inference about the deadly SARS-CoV-2.

CONCLUSIONS

This paper provides a succinct review of the literature on current understanding of the transmission, survivability, and risk SARS-CoV-2 portend to humans within the produce supply chain and calls for more evidence-based research to allay or alert us of the potential risk of fomite transmission of SARS-CoV-2. The paper also highlights examples of conventional and novel non-thermal inactivation and sanitation methods applicable to this type of virus.

Effect of Air-Polishing and Different Post-Polishing Methods on Surface Roughness of Nanofill and Microhybrid Resin Composites

Air-abrasion is a popular prophylactic procedure to maintain oral hygiene. However, depending on the applied air-abrasive powder, it can damage the surface of the tooth and restorations, making it susceptible to plaque accumulation. The purpose of this study was to investigate the effect of 5 s and 10 s air-abrasion of calcium carbonate on surface roughness (Ra) of enamel, nanofill, and microhybrid resin-composites and the effect of post-polishing with two-step rubber- (RP) or one-step brush polisher (BP) to re-establish the surface smoothness. Surface topography was visualized by scanning-electron-microscopy. The quantitative measurement of the Ra was carried out with atomic-force-microscopy. Air-abrasion for 10 s decreased the Ra of enamel as a result of abrasion of the natural surface texture. Post-polishing with RP after 10 s air-abrasion did not change the Ra or BP; however, Ra was increased significantly by scratching the surface. Air-abrasion increased the Ra of resin composites significantly, irrespective of the application time. While RP provided a similarly smooth surface to the control in the case of microhybrid resin composite, BP increased the Ra significantly. The Ra for the control group of the nanofill-resin composite was initially high, which was further increased by air-abrasion. RP and BP re-established the initial Ra with deeper and shallower scratches after BP. Both the material and treatment type showed a large effect on Ra.

A Time-Course Study on a Food Contact Material (FCM)-Certified Coating Based on Titanium Oxide Deposited onto Aluminum

Aluminum is the second most widely used metal worldwide. It is present as an additive in cosmetics, pharmaceuticals, food, and food contact materials (FCM). In this study, we confirm the bactericidal effect of a special anodizing method, based on TiO2 nanoparticles (DURALTI®) deposited on aluminum disks with different roughness and subjected to two sanitizing treatments: UV and alcohol 70%. Consequently, we perform a time-course evaluation against both Gram-negative and Gram-positive bacteria to better frame the time required to achieve the best result. Approximately 106 CFU/mL of Escherichia coli ATCC 25922; Salmonella Typhimurium ATCC 1402; Yersinia enterocolitica ATCC 9610; Pseudomonas aeruginosa ATCC 27588; Staphylococcus aureus ATCC 6538; Enterococcus faecalis ATCC 29212; Bacillus cereus ATCC 14579 and Listeria monocytogenes NCTT 10888 were inoculated onto each aluminum surface and challenged with UV and alcohol 70% at 0, 15", 30", 1', 5', 15', 30', 1, 2, 4 and 6 h. DURALTI® coating already confirmed its ability to induce a 4-logarithmic decrease (from 106 to 102 CFU/mL) after 6 h. Once each sanitizing treatment was applied, an overall bacterial inhibition occurred in a time ranging from 15'' to 1'. The results are innovative in terms of preventing microbial adhesion and growth in the food industry.

Biofilm inhibition and bactericidal activity of NiTi alloy coated with graphene oxide/silver nanoparticles via electrophoretic deposition

Biofilm formation on medical devices can induce complications. Graphene oxide/silver nanoparticles (GO/AgNPs) coated nickel-titanium (NiTi) alloy has been successfully produced. Therefore, the aim of this study was to determine the anti-bacterial and anti-biofilm effects of a GO/AgNPs coated NiTi alloy prepared by Electrophoretic deposition (EPD). GO/AgNPs were coated on NiTi alloy using various coating times. The surface characteristics of the coated NiTi alloy substrates were investigated and its anti-biofilm and anti-bacterial effect on Streptococcus mutans biofilm were determined by measuring the biofilm mass and the number of viable cells using a crystal violet assay and colony counting assay, respectively. The results showed that although the surface roughness increased in a coating time-dependent manner, there was no positive correlation between the surface roughness and the total biofilm mass. However, increased GO/AgNPs deposition produced by the increased coating time significantly reduced the number of viable bacteria in the biofilm (p < 0.05). Therefore, the GO/AgNPs on NiTi alloy have an antibacterial effect on the S. mutans biofilm. However, the increased surface roughness does not influence total biofilm mass formation (p = 0.993). Modifying the NiTi alloy surface using GO/AgNPs can be a promising coating to reduce the consequences of biofilm formation.

Effect of surface properties of ceramic materials on bacterial adhesion: A systematic review

PURPOSE

The objective of this systematic review was to describe studies that report on whether surface characteristics such as electrostatic charge, surface free energy, and surface topography promote influence on bacterial adhesion on ceramic surfaces.

MATERIAL AND METHOD

Searches in the SCOPUS, PubMed/Medline, Web of Science, EMBASE, and Google Scholar databases were performed between December 2020 and January 2021 and updated in March 2021. In addition, a manual search of reference lists from relevant retrieved articles was performed. The criteria included: studies that evaluated ceramic surfaces, which described factors such as surface free energy, electrostatic charges, roughness, zeta potential, and their relationship with bacteria.

RESULTS

Database search resulted in 348 papers. Of the 24 studies selected for full reading, 17 articles remained in this systematic review. Another five studies were found in references of articles included, totaling 22 studies. These had a high heterogeneity making it difficult to perform statistical analysis, so a descriptive analysis was performed.

CONCLUSIONS

For dental ceramics, not enough results were found to demonstrate the influence of the electrostatic condition, and its relationship with bacterial adhesion. However, studies of this review show that there is a correlation between bacterial adhesion, surface free energy, and topography.

CLINICAL SIGNIFICANCE

The knowledge of ceramics with repulsive physical-chemical interactions would allow an environment suggestive of non-adhesion of pathogenic biofilm.

Microscopic techniques to evaluate the biofilm formation ability of a marine bacterium Pseudomonas aeruginosa PFL-P1 on different substrata

Biofilm formation in bacteria is strongly affected by the nature of substrata. Different substrata such as glass, polystyrene, steel, ceramic, and rubber were used to assess the biofilm forming ability of a marine bacterium Pseudomonas aeruginosa PFL-P1 using a scanning electron microscope (SEM), atomic force microscope (AFM), and confocal laser scanning microscope (CLSM). The bacterium formed dense biofilms with varied aggregation on different substrata. SEM study revealed small rod-shaped cells with diverse arrangements within the biofilms on all the substrata under study. The AFM study revealed the highest roughness of 545 nm on the ceramic substratum. The biofilms formed on ceramic substratum were characterized with maximum roughness (742 nm), maximum peak height (1,480 nm), and maximum arithmetic mean height (611 nm), significantly higher than all the other substrata (p < .05). AFM studies confirmed that P. aeruginosa PFL-P1 exhibited biofilm heterogeneity on all the substrata. The CLSM study indicated a higher fraction of nucleic acids to α-polysaccharides ratio in the biofilms. COMSTAT analysis revealed the highest biofilm biomass of ~18 μm³ /μm² on the ceramic substratum. The maximum biofilm thickness of ~50 μm in the native state on the ceramic substratum was significantly higher than glass (p = .0015), polystyrene (p = .0001), steel (p = .0035), and rubber substrata (p = .0001). The higher surface roughness of ceramic substratum is accountable for more area for colonization, as evident from higher biomass and thickness of the biofilm. This study provides insight into the substratum properties, which modulate the biofilm forming ability in bacteria.

Bioactivity Performance of Pure Mg after Plasma Electrolytic Oxidation in Silicate-Based Solutions

The biodegradable metals, including magnesium (Mg), are a convenient alternative to permanent metals but fast uncontrolled corrosion limited wide clinical application. Formation of a barrier coating on Mg alloys could be a successful strategy for the production of a stable external layer that prevents fast corrosion. Our research was aimed to develop an Mg stable oxide coating using plasma electrolytic oxidation (PEO) in silicate-based solutions. 99.9% pure Mg alloy was anodized in electrolytes contained mixtures of sodium silicate and sodium fluoride, calcium hydroxide and sodium hydroxide. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), contact angle (CA), Photoluminescence analysis and immersion tests were performed to assess structural and long-term corrosion properties of the new coating. Biocompatibility and antibacterial potential of the new coating were evaluated using U2OS cell culture and the gram-positive Staphylococcus aureus (S. aureus, strain B 918). PEO provided the formation of a porous oxide layer with relatively high roughness. It was shown that Ca(OH)₂ was a crucial compound for oxidation and surface modification of Mg implants, treated with the PEO method. The addition of Ca²⁺ ions resulted in more intense oxidation of the Mg surface and growth of the oxide layer with a higher active surface area. Cell culture experiments demonstrated appropriate cell adhesion to all investigated coatings with a significantly better proliferation rate for the samples treated in Ca(OH)₂-containing electrolyte. In contrast, NaOH-based electrolyte provided more relevant antibacterial effects but did not support cell proliferation. In conclusion, it should be noted that PEO of Mg alloy in silicate baths containing Ca(OH)₂ provided the formation of stable biocompatible oxide coatings that could be used in the development of commercial degradable implants.

Influence of Additive Firing on the Surface Characteristics, Streptococcus mutans Viability and Optical Properties of Zirconia

The purpose of this study was to observe whether the repetitive firing of dental zirconia caused changes in surface characteristics, S. mutans viability, and optical properties of zirconia. Dental zirconia blocks were sintered and randomly distributed into seven experimental groups: F0–F6. Except for F0, which only went through sintering, the additive firing was performed in order for F1–F6. Surface roughness, contact angle, S. mutans viability by fluorescence, and translucency parameter were measured. They were all highest after sintering (F0) and decreased after additive firings (F1–F6). The additive firing of zirconia after sintering decreased surface roughness, contact angle, S. mutans viability, and translucency. The number of firings after the first firing was not found to be critical in surface characteristics, S. mutans viability, and optical property. Changes in surface characteristics might have led to a decrease in S. mutans viability, while the change of translucency was not clinically significant. This implies that additive firing may prevent secondary caries under zirconia restorations, not compromising esthetic appearance.

Implication of Surface Properties, Bacterial Motility, and Hydrodynamic Conditions on Bacterial Surface Sensing and Their Initial Adhesion

Biofilms are structured microbial communities attached to surfaces, which play a significant role in the persistence of biofoulings in both medical and industrial settings. Bacteria in biofilms are mostly embedded in a complex matrix comprised of extracellular polymeric substances that provide mechanical stability and protection against environmental adversities. Once the biofilm is matured, it becomes extremely difficult to kill bacteria or mechanically remove biofilms from solid surfaces. Therefore, interrupting the bacterial surface sensing mechanism and subsequent initial binding process of bacteria to surfaces is essential to effectively prevent biofilm-associated problems. Noting that the process of bacterial adhesion is influenced by many factors, including material surface properties, this review summarizes recent works dedicated to understanding the influences of surface charge, surface wettability, roughness, topography, stiffness, and combination of properties on bacterial adhesion. This review also highlights other factors that are often neglected in bacterial adhesion studies such as bacterial motility and the effect of hydrodynamic flow. Lastly, the present review features recent innovations in nanotechnology-based antifouling systems to engineer new concepts of antibiofilm surfaces.

Growth of Lactic Acid Bacteria on Gold-Influence of Surface Roughness and Chemical Composition

The main focus of this work was to establish a correlation between surface topography and chemistry and surface colonization by lactic acid bacteria. For this reason, we chose gold substrates with different surface architectures (i.e., smooth and nanorough) that were characterized by atomic force microscopy (AFM), electron scanning microscopy (SEM), and X-ray diffractometry (XRD). Moreover, to enhance biocompatibility, we modified gold substrates with polymeric monolayers, namely cationic dextran derivatives with different molar masses. The presence of those layers was confirmed by AFM, infrared spectroscopy (IR), and X-ray photoelectron spectroscopy (XPS). In order to determine the adhesion abilities of non-modified and modified gold surfaces, we tested three lactic acid bacteria (LAB) strains (i.e., Lactobacillus rhamnosus GG, Lactobacillus acidophilus, and Lactobacillus plantarum 299v). We have shown that surface roughness influences the surface colonization of bacteria, and the most significant impact on the growth was observed for the Lactobacillus rhamnosus GG strain. What is more, covering the gold surface with a molecular polymeric film by using the layer-by-layer (LbL) method allows additional changes in the bacterial growth, independently on the used strain. The well-being of the bacteria cells on tested surfaces was confirmed by using selective staining and fluorescence microscopy. Finally, we have determined the bacterial metabolic activity by measuring the amount of produced lactic acid regarding the growth conditions. The obtained results proved that the adhesion of bacteria to the metallic surface depends on the chemistry and topography of the surface, as well as the specific bacteria strain.

Sewer biofilm microbiome and antibiotic resistance genes as function of pipe material, source of microbes, and disinfection: field and laboratory studies

Wastewater systems are recognized pathways for the spread of antibiotic resistant bacteria, but relatively little is known about the microbial ecology of the sewer environment. Sewer biofilm colonization by antibiotic resistance gene (ARG) carrying bacteria may impact interpretations of sewage epidemiology data, water quality during sewer overflows, and hazard to utility workers. The objectives of this research were to evaluate the (1) microbiome of real and simulated sewer biofilms and their potential to accumulate ARGs and (2) susceptibility of simulated sewer biofilms to bleach disinfection. First, biofilm samples were collected from sewer municipal systems. Next, an annular biofilm reactor was used to simulate the sewer environment while controlling the pipe material (concrete vs. PVC). The reactor was operated either as fed semi-batch with sewer sediment and synthetic wastewater (Sed-SB) or fed with a continuous flow of raw sewage (WW-CF). The abundance of ARGs, human fecal marker HF183, and 16S rRNA gene copies in these biofilm samples was measured with qPCR. Amplicon sequencing was performed to compare the prokaryotic diversity between samples. Finally, the susceptibility of reactor biofilm to a 4.6% bleach disnfection protocol was evaluated using viability qPCR and amplicon sequencing. Field and WW-CF biofilms contained the most ARG copies and the microbial community compositions varied between the different biofilm samples (field, Sed-SB, and WW-CF). Pipe material did not affect the abundance of ARGs in the reactor samples. However, log removal following bleach treatment suggested that the biofilm grown on PVC surface was primarily dislodged from the surface by the bleach treatment whereas more bacteria were lysed within the biofilm that remained on the concrete surface. Viable bacteria carrying ARGs were observed following 10 minutes of treatment. This study showed that sewer biofilms can accumulate bacteria carrying ARGs and that while bleach can reduce sewer biofilm density, the protocol tested here will not completely remove the biofilms.

An introduction of biological performance of zirconia with different surface characteristics: A review

Zirconia (ZrO₂) ceramic is widely used in dentistry as a clinical dental biomaterial. In this review, we are focusing on and summarizing the biological performance of zirconia under different surface characteristics. We have included an initial tissue cell attachment study on zirconia and bacterial adhesion on zirconia. Our results suggest that surface modifications applied on zirconia may change the interfacial surface characteristics e.g. surface roughness, surface free energy, and chemistry of zirconia. The modifications also result in advanced biological performance of zirconia, including enhanced tissue cell attachment and reduction of bacterial adhesion. The recent laboratory research has provided many interesting modification methods and showed clinically interesting and promising outcomes. A few of the outcomes are validated and have been applied in clinical dentistry.

Beyond Risk: Bacterial Biofilms and Their Regulating Approaches

Bacterial biofilms are complex surface attached communities of bacteria held together by self-produced polymer matrixs mainly composed of polysaccharides, secreted proteins, and extracellular DNAs. Bacterial biofilm formation is a complex process and can be described in five main phases: (i) reversible attachment phase, where bacteria non-specifically attach to surfaces; (ii) irreversible attachment phase, which involves interaction between bacterial cells and a surface using bacterial adhesins such as fimbriae and lipopolysaccharide (LPS); (iii) production of extracellular polymeric substances (EPS) by the resident bacterial cells; (iv) biofilm maturation phase, in which bacterial cells synthesize and release signaling molecules to sense the presence of each other, conducing to the formation of microcolony and maturation of biofilms; and (v) dispersal/detachment phase, where the bacterial cells depart biofilms and comeback to independent planktonic lifestyle. Biofilm formation is detrimental in healthcare, drinking water distribution systems, food, and marine industries, etc. As a result, current studies have been focused toward control and prevention of biofilms. In an effort to get rid of harmful biofilms, various techniques and approaches have been employed that interfere with bacterial attachment, bacterial communication systems (quorum sensing, QS), and biofilm matrixs. Biofilms, however, also offer beneficial roles in a variety of fields including applications in plant protection, bioremediation, wastewater treatment, and corrosion inhibition amongst others. Development of beneficial biofilms can be promoted through manipulation of adhesion surfaces, QS and environmental conditions. This review describes the events involved in bacterial biofilm formation, lists the negative and positive aspects associated with bacterial biofilms, elaborates the main strategies currently used to regulate establishment of harmful bacterial biofilms as well as certain strategies employed to encourage formation of beneficial bacterial biofilms, and highlights the future perspectives of bacterial biofilms.

Nanoscale adhesion forces of glucosyltransferase B and C genes regulated Streptococcal mutans probed by AFM

Glucosyltransferases (Gtfs), represented by GtfB and GtfC, are important virulence factors of Streptococcus mutans and the major etiologic pathogens of tooth decay. However, the individual roles of gtfB and gtfC in the initial attachment of S. mutans are not known. We used atomic force microscopy to explore the contribution of gtfB and gtfC, as well as enamel-surface roughness, on the initial attachment of S. mutans. Adhesion forces of four S. mutans strains (wild-type, ΔgtfB, ΔgtfC, and ΔgtfBC), onto etched enamel surfaces, were determined. Force curves showed that, with increasing etching time from 0 to 10 s, the forces of all strains increased accordingly with acid-exposure time, the adhesion forces of wild-type strains were significantly greater than those of mutant strains (p < .05), and the forces of the three mutants were similar (p < .05). When the etching time was increased from 10 to 30 s, difference in force between 20 and 30 s was not observed, and adhesion forces among ΔgtfB, ΔgtfC, and wild-type strains were not significantly different when the etching time was >20 s (p > .05). These data suggest that the roughness and morphology of enamel surfaces may have a significant influence upon the initial attachment of bacteria, and that gtfB and gtfC are essential for the adhesion activity of bacteria. Furthermore, gtfB seems to be more important than gtfC for bacterial-biofilm formation, and gtfB inactivation is an effective strategy to inhibit the virulence of cariogenic biofilms.

Prechondrogenic ATDC5 Cell Attachment and Differentiation on Graphene Foam; Modulation by Surface Functionalization with Fibronectin

Graphene foam holds promise for tissue engineering applications. In this study, graphene foam was used as a three-dimension scaffold to evaluate cell attachment, cell morphology, and molecular markers of early differentiation. The aim of this study was to determine if cell attachment and elaboration of an extracellular matrix would be modulated by functionalization of graphene foam with fibronectin, an extracellular matrix protein that cells adhere well to, prior to the establishment of three-dimensional cell culture. The molecular dynamic simulation demonstrated that the fibronectin-graphene interaction was stabilized predominantly through interaction between the graphene and arginine side chains of the protein. Quasi-static and dynamic mechanical testing indicated that fibronectin functionalization of graphene altered the mechanical properties of graphene foam. The elastic strength of the scaffold increased due to fibronectin, but the viscoelastic mechanical behavior remained unchanged. An additive effect was observed in the mechanical stiffness when the graphene foam was both coated with fibronectin and cultured with cells for 28 days. Cytoskeletal organization assessed by fluorescence microscopy demonstrated a fibronectin-dependent reorganization of the actin cytoskeleton and an increase in actin stress fibers. Gene expression assessed by quantitative real-time polymerase chain reaction of 9 genes encoding cell attachment proteins (Cd44, Ctnna1, Ctnnb1, Itga3, Itga5, Itgav, Itgb1, Ncam1, Sgce), 16 genes encoding extracellular matrix proteins (Col1a1, Col2a1, Col3a1, Col5a1, Col6a1, Ecm1, Emilin1, Fn1, Hapln1, Lamb3, Postn, Sparc, Spp1, Thbs1, Thbs2, Tnc), and 9 genes encoding modulators of remodeling (Adamts1, Adamts2, Ctgf, Mmp14, Mmp2, Tgfbi, Timp1, Timp2, Timp3) indicated that graphene foam provided a microenvironment conducive to expression of genes that are important in early chondrogenesis. Functionalization of graphene foam with fibronectin modified the cellular response to graphene foam, demonstrated by decreases in relative gene expression levels. These findings illustrate the combinatorial factors of microscale materials properties and nanoscale molecular features to consider in the design of three-dimensional graphene scaffolds for tissue engineering applications.

Innovation by Computer-Aided Design/Computer-Aided Manufacturing Technology: A Look at Infection Prevention in Dental Settings

Recent data indicates limited awareness and compliance on infection prevention procedures by dental offices and by dental laboratories. Guidelines for infection prevention in dentistry have been published by Centres for Disease Control and Prevention since 2003; the section “IX-Special consideration” includes a subsection concerning the prevention in dental laboratories, but it has not been modernised in later versions to fit the needs of traditional and computer-aided technology. Traditional techniques required disinfecting items (impression, chewing waxes, and appliances) with well-suited products, which are also chosen for limiting impression changes or appliance deterioration. Effective procedures are available with difficulties. Some of these contain irritant or non-eco-friendly disinfectants. The transport of impression, to dental laboratories, is often delayed with limited precautions for limiting cross-infection. Gypsum casts are frequently contaminated mainly by bacteria and their antibiotic-resistant strains and even stored for long periods during dental implant supported restoration and orthodontic therapy, becoming a hidden source of infection. Nowadays, computer-aided design/computer-aided manufacturing technology seems to be an interesting way to promote both business and safety, being more comfortable for patients and more accurate than traditional technology. A further advantage is easier infection prevention since, for the most part, mainly digital impression and casts are not a source of cross-infection and the transport of contaminated items is reduced and limited to try-in stages. Nevertheless, a peculiar feature is that a digital electronic file is of course unalterable, but may be ruined by a computer virus. Additionally, the reconditioning of scanner tips is determinant for the optical characteristics and long term use of the scanner, but information for its reconditioning from producers is often limited. This study focuses on some critical points including (a) insufficient guidelines, (b) choice of proper procedure for scanner reconditioning, and (c) data protection in relation to patient privacy.

Surface Immobilization of Nano-Silver on Polymeric Medical Devices to Prevent Bacterial Biofilm Formation

: Bacterial biofilm on medical devices is difficult to eradicate. Many have capitalized the anti-infective capability of silver ions (Ag+) by incorporating nano-silver (nAg) in a biodegradable coating, which is then laid on polymeric medical devices. However, such coating can be subjected to premature dissolution, particularly in harsh diseased tissue microenvironment, leading to rapid nAg clearance. It stands to reason that impregnating nAg directly onto the device, at the surface, is a more ideal solution. We tested this concept for a corneal prosthesis by immobilizing nAg and nano-hydroxyapatite (nHAp) on poly(methyl methacrylate), and tested its biocompatibility with human stromal cells and antimicrobial performance against biofilm-forming pathogens, Pseudomonas aeruginosa and Staphylococcus aureus. Three different dual-functionalized substrates-high Ag (referred to as 75:25 HAp:Ag); intermediate Ag (95:5 HAp:Ag); and low Ag (99:1 HAp:Ag) were studied. The 75:25 HAp:Ag was effective in inhibiting biofilm formation, but was cytotoxic. The 95:5 HAp:Ag showed the best selectivity among the three substrates; it prevented biofilm formation of both pathogens and had excellent biocompatibility. The coating was also effective in eliminating non-adherent bacteria in the culture media. However, a 28-day incubation in artificial tear fluid revealed a ~40% reduction in Ag+ release, compared to freshly-coated substrates. The reduction affected the inhibition of S. aureus growth, but not the P. aeruginosa. Our findings suggest that Ag+ released from surface-immobilized nAg diminishes over time and becomes less effective in suppressing biofilm formation of Gram-positive bacteria, such as S. aureus. This advocates the coating, more as a protection against perioperative and early postoperative infections, and less as a long-term preventive solution.

Characterization of Biofilm Formed by Phenanthrene-Degrading Bacteria on Rice Root Surfaces for Reduction of PAH Contamination in Rice

One effective method in to reduce the uptake of organic contaminants by plants is the development of a root barrier. In this study, the characterization of biofilm structure and function by phenanthrene-degrading Pseudomonas sp. JM2-gfp on rice root surfaces were carried out. Our results showed that root surfaces from three rice species, namely Liaojing401, Koshihikari, and Zhenzhuhong all present hydrophobicity and a high initial adhesion of strain JM2-gfp. Matured robust biofilm formation occurred at 48 h on the root surfaces. The biofilm exhibited cell dense aggregates and biomass embedded in the extracellular polymeric substance (EPS) matrix. EPS composition results showed that the proteins, carbohydrates, lipids and nucleic acids are produced in the biofilm, while the content varied with rice species. Under the initial concentration of phenanthrene 50 mg·L-1, the residual phenanthrene in plant roots from 'Zhengzhuhong', 'Koshihikari' and 'Liaojing401' with biofilm mediated were significantly decreased by 71.9%, 69.3% and 58.7%, respectively, compared to those without biofilm groups after 10 days of exposure. Thus, the biofilm colonized on roots plays an important role of degradation in order to reduce the level of phenanthrene uptake of plants. Thereby, the present work provides significant new insights into lowering the environmental risks of polycyclic aromatic hydrocarbons (PAHs) in crop products from contaminated agriculture soils.

Periodicities in the roughness and biofilm growth on glass substrate with etching time: Hydrofluoric acid etchant

Adherence of the microorganism to submerged solid surfaces leads to biofilm formation. Biofilm formation modifies the surfaces in favor of bacteria facilitating the survival of the bacteria under different stressed conditions. On the other hand, the formation of biofilm has a direct adverse economic impact in various industries and more importantly in medical practices. This adherence is the reason for the failure of many indwelling medical devices. Surface biofilm adhesion is the key to biofilm growth and stability. Hence this adhesion needs to be substantially lowered to inhibit biofilm stability. Both chemical and physical properties of the surface influence biofilm formation and modulating these properties can control this formation. In this study, we have investigated the effect of Hydrofluoric acid (HF), at a specific concentration as an etchant, on the surface morphology of substrates and the growth of biofilms of Pseudomonas aeruginosa. and Staphylococcus aureus. We find that the bacterial counts on the etched surfaces undergo a periodic increase and decrease. This, on one hand, shows the close correlation between the biofilm growth and the particular roughness scale, and on the other hand, explains the existing contradictory results regarding the effects of etching on substrate roughness and biofilm growth. We propose a simple model of a sequence of hole formation, hole expansion and etching away of the hole walls to form a new, comparatively smooth surface, coupled with the preferential accumulation of bacteria at the hole edges, to explain these periodicities.

Current Insights into the Modulation of Oral Bacterial Degradation of Dental Polymeric Restorative Materials

Dental polymeric composites have become the first choice for cavity restorations due to their esthetics and capacity to be bonded to the tooth. However, the oral cavity is considered to be harsh environment for a polymeric material. Oral biofilms can degrade the polymeric components, thus compromising the marginal integrity and leading to the recurrence of caries. Recurrent caries around restorations has been reported as the main reason for restoration failure. The degradation of materials greatly compromises the clinical longevity. This review focuses on the degradation process of resin composites by oral biofilms, the mechanisms of degradation and its consequences. In addition, potential future developments in the area of resin-based dental biomaterials with an emphasis on anti-biofilm strategies are also reviewed.