Biosorption of cationic dyes by Pará chestnut husk (Bertholletia excelsa)

Modeling competitive biosorption for methylene blue removal on rape straw powders using response surface methodology in a ternary dye aqueous solution

The improvement of biosorption efficiency for selective dye removal in a multi-dye aqueous system has become an increasingly significant research topic. However, the competitive effects of coexisting dyes and the target dye in such systems remain uncertain due to complex interactions between adsorbent and coexisting dyes. Therefore, in this research, response surface methodology (RSM) model was effectively employed to investigate the competitive effects of allura red (AR) and malachite green (MG) on methylene blue (MB) removal in a ternary dye aqueous system using three different parts of rape straw powders. In the current design of RSM, the initial concentrations of AR and MG dyes ranging from 0 mg·L-1 to 500 mg·L-1 were considered as influencing factors, while the removal rates of MB on adsorbents at an initial concentration of 500 mg·L-1 were established as response values. The RSM models exhibited high correlation coefficients with adjusted R2 values of 0.9908 (pith core), 0.9870 (seedpods), and 0.9902 (shells), respectively, indicating a close fitted between predicted and actual values. The proposed models indicated that the perturbation effects of initial AR and MG concentrations were observed on the removal rates of MB by three types of rape straw powders in a ternary dye aqueous system, resulting in a decrease in MB removal rates, particularly at higher initial AR concentration due to stronger competitive effects compared to initial MG concentration. The structures of rape straw powders, including pith core, seedpods and shell, were analyzed using scanning eletron microscoe (SEM), energy dispersive spectroscopy (EDS), N2 physisorption isotherm, frourier transform infared spectroscopy (FTIR), Zeta potential classes and fluorescence spectrum before and after adsorption of MB in various dye aqueous systems. The characteristics of rape straw powders suggested that similar adsorption mechanisms, such as electrostatic attraction, pore diffusion, and group complex formation for MB, AR, and MG, respectively, occurred on the surfaces of adsorbents during their respective adsorption processes. This leads to significant competitive effects on the removal rates of MB in a ternary dye aqueous system, which are particularly influenced by initial AR concentrations as confirmed through fluorescence spectrum analysis.

Enhancing Methylene Blue Dye Removal using pyrolyzed Mytella falcata Shells: Characterization, Kinetics, Isotherm, and Regeneration through Photolysis and Peroxidation

The potential of pyrolyzed Mytella falcata shells as an adsorbent for removing methylene blue dye molecules from aqueous solutions was investigated. The study found that the adsorbent produced at 600 °C of pyrolysis temperature, with an adsorbent mass of 0.5 g, particle diameter of 0.297-0.149 mm, and pH 12.0, demonstrated the highest dye molecule removal efficiency of 82.41%. The material's porosity was observed through scanning electron microscopy, which is favorable for adsorption, while Fourier-transform infrared spectroscopy and X-Ray diffraction analysis analyses confirmed the presence of calcium carbonate in the crystalline phases. The pseudo-second order model was found to be the best fit for the data, suggesting that the adsorption mechanism involves two steps: external diffusion and diffusion via the solid pores. The Redlich-Peterson isotherm model better represented the equilibrium data, and the methylene blue adsorption was found to be spontaneous, favorable, and endothermic. The hydrogen peroxide with UV oxidation was found to be the most efficient method of regeneration, with a regeneration percentage of 63% achieved using 600 mmol.L-1 of oxidizing agents. The results suggest that pyrolyzed Mytella falcata shells could serve as an ecologically viable adsorbent alternative, reducing the amount of waste produced in the local environment and at the same time removing pollutants from the water. The material's adsorption capacity remained almost constant in the first adsorption-oxidation cycles, indicating its potential for repeated use.

A Novel High-Efficiency Natural Biosorbent Material Obtained from Sour Cherry (Prunus cerasus) Leaf Biomass for Cationic Dyes Adsorption

The present study aimed to investigate the potential of a new lignocellulosic biosorbent material derived from mature leaves of sour cherry (Prunus cerasus L.) for removing methylene blue and crystal violet dyes from aqueous solutions. The material was first characterized using several specific techniques (SEM, FTIR, color analysis). Then, the adsorption process mechanism was investigated through studies related to adsorption equilibrium, kinetics, and thermodynamics. A desorption study was also performed. Results showed that the Sips isotherm provided the best fit for the adsorption process of both dyes, with a maximum adsorption capacity of 168.6 (mg g^-1) for methylene blue and 524.1 (mg g^-1) for crystal violet, outperforming the capacity of other similar adsorbents. The contact time needed to reach equilibrium was 40 min for both studied dyes. The Elovich equation is the most suitable model for describing the adsorption of methylene blue, while the general order model is better suited for the adsorption of crystal violet dye. Thermodynamic analyses revealed the adsorption process to be spontaneous, favorable, and exothermic, with physical adsorption involved as the primary mechanism. The obtained results suggest that sour cherry leaves powder can be a highly efficient, eco-friendly, and cost-effective adsorbent for removing methylene blue and crystal violet dyes from aqueous solutions.

Novel Adsorbent Material from Plinia cauliflora for Removal of Cationic Dye from Aqueous Solution

The food industry is responsible for the generation of large amounts of organic residues, which can lead to negative environmental and economic impacts when incorrectly disposed of. The jaboticaba peel is an example of organic waste, widely used in industry due to its organoleptic characteristcs. In this study, residues collected during the extraction of bioactive compounds from jaboticaba bark (JB) were chemically activated with H₃PO₄ and NaOH and used to develop a low-cost adsorbent material for the removal of the cationic dye methylene blue (MB). For all adsorbents, the batch tests were carried out with the adsorbent dosage of 0.5 g L^-1 and neutral pH, previously determined by 2² factorial design. In the kinetics tests, JB and JB-NaOH presented a fast adsorption rate, reaching equilibrium in 30 min. For JB-H₃PO₄, the equilibrium was reached in 60 min. JB equilibrium data were best represented by the Langmuir model and JB-NaOH and JB-H₃PO₄ data by the Freundlich model. The maximum adsorption capacities from JB, JB-NaOH, and JB-H₃PO₄ were 305.81 mg g^-1, 241.10 mg g^-1, and 122.72 mg g^-1, respectively. The results indicate that chemical activations promoted an increase in the volume of large pores but interacted with functional groups responsible for MB adsorption. Therefore, JB has the highest adsorption capacity, thus presenting as a low-cost and sustainable alternative to add value to the product, and it also contributes to water decontamination studies, resulting in a zero-waste approach.

Sphagnum perichaetiale Hampe biomass as a novel, green, and low-cost biosorbent in the adsorption of toxic crystal violet dye

In this study, the Sphagnum perichaetiale Hampe biomass was collected, characterized, and used as a biosorbent in the removal of crystal violet from water. The chemical and morphological results suggest that even after minimal experimental procedures, the biomass presented interesting properties regarding the adsorption of contaminants. Results of adsorption showed that the pH was not a relevant parameter and the best adsorbent dosage was 0.26 g L^-1. The kinetic results presented an initial fast step and the equilibrium was reached after 180 min. For the equilibrium data, the best adjustment occurred for the Sips model, reaching a maximum adsorption capacity of 271.05 mg g^-1 and the removal percentage obtained in the maximum adsorbent dosage was 97.11%. The thermodynamic studies indicated a reversible process and that the mass-transfer phenomena is governed by the physisorption mechanism. In addition to its great performance as a biosorbent, Sphagnum perichaetiale biomass also presents economic and sustainable benefits, as its production does not require costs with reagents or energy, usually used in chemical and physical activation. The reversible process indicated that the biosorbent could be reused, decreasing the costs related to the treatment of the effluents. Thus, Sphagnum perichaetiale biomass can be considered an efficient low-cost and eco-friendly biosorbent.

Brazilian Agro-industrial Wastes as Potential Textile and Other Raw Materials: a Sustainable Approach

The Brazilian agro-industrial chain generates about 291 million/tons/year of wastes, which, if inadequately destinated, could originate social and environmental risks. There is a growing need for the use of alternative raw materials to replace that originated from fossil resources in the Brazilian industry. Renewable materials play an important role on the sustainability of ecosystems and materials’ circularity. The issue has acquired importance in light of recent bio-based agro-fiber development potential applications. Considering sustainability guidelines, this study aimed to analyze the main Brazilian agro-industrial waste crops (temporary and permanent) as important sources of natural fibers and other raw materials. A systematic review of the literature (SRL) about Brazilian researches, based on concepts of industrial ecology, and the creation of a bibliometric analysis network were carried out. The agricultural biomass related to the main crops presents characteristics making them suitable to be applied for textiles, as natural fibers and polymers, in biosorbents for industrial effluents, and cellulose obtention and reinforcement material in composites. Thus, scientific investment in researches on materials and technology development are necessary to provide applications that could meet current and future demands and expand the scope of new materials for sustainability.

Crystal Violet Adsorption on Eco-Friendly Lignocellulosic Material Obtained from Motherwort (Leonurus cardiaca L.) Biomass

The performance of a new eco-friendly adsorbent, obtained from motherwort (Leonurus cardiaca L.) biomass after minimum processing, in crystal violet dye removal from aqueous solutions was studied. Firstly, the adsorbent material was characterized using several technics, such as FTIR, pH_PZC determination, SEM and color analysis. The next step was to determine the influence of initial dye concentration, contact time, temperature, pH, adsorbent dose and ionic strength on adsorbent adsorption capacity. Equilibrium, kinetic, thermodynamic, optimization and desorption studies were performed in a batch system for studying all aspects related to the adsorption process. The sips isotherm best fit the experimental data with a predicted maximum adsorption capacity of 125.6 (mg g⁻¹). The kinetic data indicate that equilibrium is reached at 50 min and that general order is the best kinetic model to describe the dye retention. The process is endothermic, spontaneous, favorable and supposed to be a physical adsorption. In addition to establishing the optimal adsorption conditions, Taguchi methods and ANOVA analysis showed that the pH is the most influencing parameter of the adsorption process, having a contribution of 61.64%. All the presented data show that the motherwort biomass powder is very suitable to be used as at low-cost, easy available and effective adsorbent for the crystal violet dye removal from aqueous solutions.

Application of biowaste generated by the production chain of pitaya fruit (Hylocereus undatus) as an efficient adsorbent for removal of naproxen in water

Pharmaceutical compounds are a serious problem in the environment. They cause damage to the aquatic, animal, and human organisms and soon became considered emerging pollutants where their removal is extremely urgent. Among the techniques used, adsorption has been used with success, where several adsorbent materials, including those from residual biomass, have been used to remove these pollutants. In this study, the skins of the pitaya fruit (Hylocereus undatus) productive chain were carbonized with ZnCl₂ to obtain activated carbon and later used in the adsorption of the drug naproxen (NPX) in a batch system. The Freundlich model demonstrated a better adjustment for the equilibrium isotherms. A high adsorption capacity for NPX (158.81 mg g^-1) was obtained at 328 K, which can be attributed to the remarkable textural properties of the adsorbent, besides certain functional groups present on its surface. Thermodynamic studies confirmed the endothermic nature of the adsorption process (∆H⁰ = 0.2898 kJ mol^-1). The linear driving force model (LDF) presented a good statistical adjustment to the experimental kinetic data. The application of the material in the treatment of simulated wastewater composed of various pharmaceutical drugs and salts was very promising, reaching 75.7% removal. Therefore, it can be inferred that the application of activated carbon derived from pitaya bark is highly promising in removing the NPX drug and treating synthetic mixtures containing other pharmaceutical substances.

Efficient Removal of Methylene Blue Using Living Biomass of the Microalga Chlamydomonas moewusii: Kinetics and Equilibrium Studies

The efficiency of the living biomass of the microalga Chlamydomonas moewusii in removing methylene blue dye is determined. The kinetics, equilibrium isotherms, and the effects on this process of the pH, contact time, and initial concentration of the dye are studied. Fourier transform infrared spectrometry and point of zero charge are used to characterize the biomass and explore the process. The maximum removal capacity derived from the Langmuir isotherm is 212.41 ± 4.55 mg/g after 7 h of contact time at pH 7. The removal process is rapid because kinetic studies revealed that the best fit of the data is with pseudo-third-order kinetics. The removal efficiency is dependent on the pH; as the pH increased, the efficiency is higher. These results show that the living biomass of this microalga is a very efficient biosorbent and therefore very suitable for the removal of methylene blue from aqueous solutions.

Bathurst Burr (Xanthium spinosum) Powder-A New Natural Effective Adsorbent for Crystal Violet Dye Removal from Synthetic Wastewaters

A new natural adsorbent material, Bathurst burr powder, was used to remove crystal violet dye from synthetic wastewaters. Particle size distribution and SEM and FTIR analyses were performed to characterize it. The effect of the operational adsorption process parameters (pH, ionic strength, initial dye concentration, adsorbent dose, contact time, temperature) onto the adsorption process was evaluated in a batch system. Equilibrium, kinetic, and thermodynamic studies were performed in order to understand the adsorption process. Taguchi method and ANOVA test were used to optimize the dye adsorption conditions and to establish the percentage contribution of each factor, respectively. The accuracy of the Taguchi prediction method was analyzed by correlating the predicted dye removal efficiency with the experimentally determined one. The particle size distribution analysis showed that 82.15% of the adsorbent particles have an average size below 0.5 mm. The adsorption process followed the Langmuir isotherm and pseudo-second order kinetic model. Maximum adsorption capacity value (164.10 mg·g⁻¹) was higher compared to many similar adsorbents. The process was endothermic, spontaneous, and favorably involving a physisorption mechanism. The Taguchi method showed that the most influential controllable factor was pH (65% contribution in adsorption efficiency) and the data analysis indicates a very good accuracy of the experimental design (R² = 0.994). The obtained results demonstrated that Bathurst burr powder can be used as a cheap and efficient adsorbent for crystal violet dye removal from aqueous solution.

Chitin-psyllium based aerogel for the efficient removal of crystal violet from aqueous solutions

A new alternative aerogel was prepared from low-cost chitin and psyllium biopolymers to adsorb crystal violet (CV) dye from liquid media and possibly treat effluents containing other dyes. The aerogel was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM), which demonstrated that aerogel has a typical structure of amorphous materials and presented a randomly interconnected porous structure that resembles an open pore network. 2.5 g L^-1 of aerogel was able to remove 86.00% of CV from solutions, and the natural pH of the CV solution was considered the more adequate for adsorption. The pseudo-second-order (PSO) model satisfactorily described the adsorption kinetics, and the Freundlich model was suitable to represent the adsorption equilibrium. The maximum experimental capacity achieved was 227.11 mg g^-1, which indicates that aerogel is very efficient and competitive with several adsorbents. Tests using a simulated effluent showed that aerogel has excellent potential to treat real colored effluents.

Successful adsorption of bright blue and methylene blue on modified pods of Caesalpinia echinata in discontinuous system

Pods of the forest species Caesalpinia echinata were used as an alternative adsorbent to remove bright blue (BB) and methylene blue (MB) dyes. The raw and acid-treated samples were characterized by techniques like SEM, XRD, and FTIR. The acid-treated pod sample was characterized by an amorphous structure containing several cavities, bumps, and functional groups. The Elovich model was the most satisfactory to describe the adsorption kinetic data. The isothermal studies were better described by the Langmuir model for BB dye, with a maximum capacity of 261 mg g^-1, and Tóth model for MB dye, giving a maximum capacity of 288 mg g^-1. The thermodynamic study indicated a spontaneous and favorable process and endothermic nature for both dyes. In the treatment of two simulated effluents containing a mixture of different compounds such as dyes and salts, to simulate real wastewaters, the adsorbent was highly efficient, presenting around 80% of color removal for both effluents. Therefore, the acid-treated pods of Caesalpinia echinata have great potential to be applied as an alternative adsorbents in treating colored effluents in discontinuous systems.

Transforming pods of the species Capparis flexuosa into effective biosorbent to remove blue methylene and bright blue in discontinuous and continuous systems

This study investigates, for the first time, the applicability of seed pods from Capparis flexuosa as an alternative biosorbent to remove methylene blue and bright blue from aqueous medium using continuous and batch systems. The biosorbent was characterized by different techniques, whose particles presented rough surface and large pores and functional groups existing on its surface. In the batch system, an adsorptive capacity of 96.40 mg g^-1 and 80% of methylene blue removal was reached with 0.9 g L^-1 of adsorbent at pH 10, whereas 109.7 mg g^-1 and 83% of bright blue removal was observed using 0.8 g L^-1 of adsorbent at pH 2.0. The Elovich model adjusted the experimental data satisfactorily for both dyes. Tóth model for the MB best described the equilibrium data, and the Langmuir model for the bright blue both favored by the increase of temperature and dyes' concentration. The maximum capacities obtained were 280.78 mg g^-1 and 342.85 mg g^-1 for methylene blue and bright blue, respectively. The thermodynamic parameters indicated spontaneous processes, with endothermic behavior for both dyes. The fixed adsorption experiments using Capparis flexuosa seed pods showed adsorptive capacities of 158.65 and 205.81 mg g^-1 for the methylene blue and bright blue, respectively. The overall results indicated that the pods of the Capparis flexuosa could be an ecological, effective, and economical alternative in the removal of dyes for both continuous and batch systems.

Application of seed residues from Anadenanthera macrocarpa and Cedrela fissilis as alternative adsorbents for remarkable removal of methylene blue dye in aqueous solutions

Two novel ecological and low-cost adsorbents were prepared from seed residues of the tree species Anadenanthera macrocarpa and Cedrela fissilis for the removal of methylene blue dye in water. The materials were comminuted and characterized by different techniques. The particles of samples have a rough surface with cavities. The optimum dosage and pH for both materials were 1 g L^-1 and pH 8. The pseudo-second-order model was the most suitable for describing the adsorption kinetics for both systems. The Anadenanthera macrocarpa presented a maximum experimental capacity of 228 mg g^-1, while the Cedrela fissilis, a similar capacity of 230 mg g^-1 at 328 K. The Tóth model was proper for describing the equilibrium curves for both systems. The thermodynamic indicators show that the adsorption process is spontaneous and endothermic for both materials. The application of materials for the simulated effluent treatment showed 74 and 78% of color removal using Anadenanthera macrocarpa and Cedrela fissilis samples, respectively. Overall, seed residues of Anadenanthera macrocarpa and Cedrela fissilis could be potentially applied for adsorptive removal of colored contaminants in wastewater.

Macro-fungal (Agaricus bisporus) wastes as an adsorbent in the removal of the acid red 97 and crystal violet dyes from ideal colored effluents

The wastes from the macro-fungus Agaricus bisporus were used as an eco-friendly and low-cost adsorbent for the treatment of colored effluents containing the recalcitrant dyes, acid red 97 (AR97) and crystal violet (CV). The macro-fungal waste presented an amorphous structure, composed of particles with different sizes and shapes. Also, it presents typical functional chemical groups of proteins and carbohydrates with a point of zero charge of 4.6. The optimum conditions for the dosage were found to be as follows: 0.5 g L^-1 with an initial pH at 2.0 for the AR97 and 8.0 for the CV. From the kinetic test, it was found that it took 210 min and an adsorption capacity of 165 mg g^-1 for the AR97. Concerning the CV kinetics, it took 120 min to reach the equilibrium and it achieved an adsorption capacity of 165.9 mg g^-1. The Elovich model was the most proper model for describing the experimental data, achieving an R² ≥ 0.997 and MSE ≤ 36.98 (mg g^-1)². The isotherm curves were best represented by the Langmuir model, predicting maximum adsorption capacity of 372.69 and 228.74 mg g^-1 for the AR97 and CV, respectively. The process was spontaneous and favorable for both dyes. The ∆H⁰ values were 9.53 and 10.69 kJ mol^-1 for AR97 and CV, respectively, indicating physical and endothermic adsorption. Overall, the wastes from Agaricus bisporus have the potential to adsorb cationic and anionic dyes, thus solving environmental problems related to water quality and residue disposal.

Evaluation of Ocotea puberula bark powder (OPBP) as an effective adsorbent to uptake crystal violet from colored effluents: alternative kinetic approaches

The Ocotea puberula bark powder (OPBP) was evaluated as an effective adsorbent for the removal of crystal violet (CV) from colored effluents. OPBP was characterized and presented a surface with large cavities, organized as a honeycomb. The main functional groups of OPBP were O-H, N-H, C=O, and C-O-C. The adsorption of CV on OPBP was favorable at pH 9 with a dosage of 0.75 g L^-1. The Avrami model was the most suitable to represent the adsorption kinetic profile, being the estimated equilibrium concentration value of 3.37 mg L^-1 for an initial concentration of 50 mg L^-1 (CV removal of 93.3%). The equilibrium was reached within 90 min. The data were better described by the Langmuir isotherm, reaching a maximum adsorption capacity of 444.34 mg g^-1 at 328 K. The Gibbs free energy ranged from - 26.3554 to - 27.8055 kJ mol^-1, and the enthalpy variation was - 11.1519 kJ mol^-1. The external mass transfer was the rate-limiting step, with Biot numbers ranging from 0.0011 to 0.25. Lastly, OPBP application for the treatment of two different simulated effluents was effective, achieving a removal percentage of 90%.

Treatment of water containing methylene by biosorption using Brazilian berry seeds (Eugenia uniflora)

Brazilian berry seeds (Eugenia uniflora) were used as an eco-friendly and low-cost biosorbent for the treatment of textile effluents containing methylene blue. Characterization techniques indicated that Brazilian berry seeds are constituted of irregular particles, mainly composed of lignin and holocellulose groups, distributed in an amorphous structure. Methylene blue biosorption was favorable at pH of 8, using a biosorbent dosage of 0.8 g L^-1. The equilibrium was reached in the first 20 min for lower M methylene blue concentrations and 120 min for higher methylene blue concentrations. Furthermore, the general and pseudo-second-order models were suitable for describing the kinetic data. Langmuir was the most adequate model for describing the isotherm curves, predicting a biosorption capacity of 189.6 mg g^-1 at 328 K. Biosorption was spontaneous (- 9.54 ≤ ΔG⁰ ≤ -8.06 kJ mol^-1) and endothermic, with standard enthalpy change of 6.11 kJ mol^-1. Brazilian berry seeds were successfully used to remove the color of two different simulated textile effluents, achieving 92.2% and 73.5% of removal. Last, the fixed-bed experiment showed that a column packed with Brazilian berry seeds can operate during 840 min, attaining biosorption capacity of 88.7 mg g^-1. The data here presented indicates that textile effluents containing methylene blue can be easily and successfully treated by an eco-friendly and low-cost biosorbent like Brazilian berry seeds.

Araticum (Annona crassiflora) seed powder (ASP) for the treatment of colored effluents by biosorption

Dyes are widely used in many industrial sectors, many contain harmful substances to human health, and their release into the environment entails several environmental problems, generating a major worldwide concern as water resources are increasingly limited. The development of cheap and efficient biosorbents that remove these pollutants is of utmost importance. In this study, powdered seeds of the araticum fruit (Annona crassiflora) were used in the biosorption of crystal violet (CV) dye from aqueous solutions and simulated textile effluents. Through the characterization techniques, it can be observed that the material presented an amorphous structure, containing an irregular surface composed mainly by groups containing carbon, hydrogen, and oxygen. CV biosorption was favored at the natural pH of the solution (7.5) for a dosage of 0.7 g L^-1 of araticum seed powder. The pseudo-second-order model was the most suitable to represent the biosorption kinetics in the removal of the CV. Biosorption capacity reached equilibrium in the first minutes at the lowest concentrations, and, at the highest, after 120 min. The equilibrium data were well represented by the Langmuir model, with a maximum biosorption capacity of 300.96 mg g^-1 at 328 K. Biosorption had a spontaneous and endothermic nature. In the treatment of a simulated effluent, the biosorbent removed 87.8% of the color, proving to be efficient. Therefore, the araticum seeds powder (ASP) can be used as a low-cost material for the treatment of colored effluents containing the crystal violet (CV) dye.

Use of sawdust as pretreatment of photo-Fenton process in the depuration of landfill leachate

A research of the depuration of landfill leachate using sawdust as activated carbon material to be applied in adsorption process as pretreatment of solar photo-Fenton and solar photo-Fenton + O₃, was carried out. The activated sawdust shows very irregular shapes and pores, and a high capacity to remove ammonium (87.0%), iron (70.2%) and copper (61.1%). As well, it has the capacity to remove humic acid (18.3%), COD (33.7%) and colour (19.5%). Also, a removal of organic matter was obtained in terms of COD (76.4%), colour (74.9%), nitrate (50.0%), ammonium (12.8%) and humic acid (73.3%) due to the joint action of ozone and solar photo-Fenton process. The overall treatment (filtration, adsorption, photo-Fenton and photo-Fenton + ozone) carried out showed a very high removal of pollutants, with a reduction of COD, colour, ammonium and humic acid of 95.1%, 95.0%, 94.5% and 97.9%, respectively. With this enhancement in the landfill leachate (LL) quality, there is a reduction of toxicity, obtaining with the LL 50% diluted, a germination index for Lactuca sativa of 20% GI. This shows that the incorporation of sawdust is a useful pretreatment of photo-Fenton in the treatment of landfill leachate.

Simultaneous biosorption of Cd(II), Ni(II) and Pb(II) onto a brown macroalgae Fucus vesiculosus: Mono- and multi-component isotherms, kinetics and thermodynamics

Due to the anthropic activities, several heavy metal ions are introduced into the environment, impacting ecosystems and local activities. In this context, the biosorption process using algae represents an alternative form for these compounds remediation due to the advantages derived from the biosorbent and process efficiency. Thus, the present study evaluated Cadmium (Cd(II)), Nickel (Ni(II)) and Lead (Pb(II)) remediation from aqueous media in mono- and multi-component systems. The biosorbent was characterized in terms of its morphology and composition and parameters involving equilibrium, kinetics, and thermodynamics were investigated. Lastly, the sample was considered in a real surface water sample remediation impacted by a mining dam rupture. Except for Freundlich, all isotherm models tested satisfactorily adjusted to the experimental data for a mono-component system. The maximum biosorption capacities (qm) were 143.2 ± 7.5, 70.1 ± 1.9, 516.3 ± 12.5 mg g-1 for Cd(II), Ni(II) and Pb(II) ions, respectively. When binary systems were considered, an antagonism effect was observed. The biosorption of Cd(II) was drastically affected by the presence of Ni(II), while Pb(II) biosorption in general was less affected by other metals presence. As observed for the binary system, the worst effect in the ternary system was observed for Cd(II) biosorption, being significantly affected by Ni(II) and Pb(II) presence. Overall, the biosorption order in mono- and multi-component systems was found to be Pb(II) ≫ Cd(II) > Ni(II). The affinity for the metals ions was also observed by Elovich's desorption constant, in which aPb(II)≪aCd(II)aCd(II), achieving an equilibrium passed 49 min. From the stages involved in biosorption process, film diffusion presented the greatest contribution as control-stage obtaining a lower diffusion coefficient in all cases. The process was spontaneous in all temperature range evaluated, considered exothermic for all metal ions evaluated. Iron, manganese and nickel concentrations in real surface water samples were higher than the allowed by the Brazilian National Environment Council (CONAMA). Comparing the hazard index values before and after the biosorption process, a reduction superior to 8 × was observed (HIbefore: 3.36, HIafter: 0.40), in which there was no non-carcinogenic risk imposed to the surrounding population after the treatment applied.

Application of Beauveria bassiana spore waste as adsorbent to uptake acid red 97 dye from aqueous medium

The adsorption of acid red 97 dye (RED 97) by the waste of the filamentous fungus Beauveria bassiana was analyzed. The adsorbent was obtained as a waste of a fermentative process, and characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray powder diffractometry (XRD), and specific surface area (BET). After the characterization, adsorption tests were carried out to determine the ideal conditions of pH, adsorbent mass, and contact time for the process. Adsorption isotherms, thermodynamic studies, and the treatment of textile effluent were also investigated. The adsorbent characterization allowed the visualization of its amorphous structure, with irregular and heterogeneous particles. The pore diameter was 51.9 nm and the surface area was 0.247 m² g^-1. 1.2 g L^-1 of the adsorbent and pH of 2.0 were the ideal conditions for RED 97 adsorption. The pseudo-second-order kinetic model was the most appropriate to represent the experimental data, being the equilibrium reached in about 110 min. The Langmuir model was the most suitable to represent the equilibrium data, with maximum adsorption capacity of 194.1 mg g^-1 at 45 °C. The adsorption processes was thermodynamically spontaneous, favorable, and exothermic. In the treatment of a real textile effluent, 5 g L^-1 of the spores was capable to decolorize 70% of the solution. Therefore, spore wastes of Beauveria bassiana were promising for RED 97 adsorption.

Adsorptive decontamination of wastewater containing methylene blue dye using golden trumpet tree bark (Handroanthus albus)

The golden trumpet tree bark (GTB), a wood-processing residue, was tested as adsorbent material for decontamination of wastewaters containing methylene blue dye (MB). The powdered material was preponderantly amorphous, containing an irregular surface with the presence of lignin and holocellulose. The adsorption was favorable at basic pH of 10 and adsorbent dosage of 0.5 g L^-1. The kinetics has finished in only 30 min and fitted by the general order model (GO). The isotherm behaviors were successfully represented by the Langmuir model. The value found for the maximum adsorption capacity was 232.25 mg g^-1, being obtained at 328 K. The standard variation of Gibbs free energy (ΔG⁰) ranged from - 10.77 to - 8.09 kJ mol^-1, indicating a spontaneous and favorable adsorption. A variation of standard enthalpy (ΔH⁰) of 18.58 kJ mol^-1 revealed an endothermic adsorption. A sloped forward curve was found in the continuous operation, with breakthrough time (t_b) of 325 min. The stoichiometry capacity of the column (q_eq) and the length of mass transfer zone (Z_m) were, respectively, 23.57 mg g^-1 and 11.28 cm. The GTB was efficient in the treatment of a simulated effluent, obtaining color removal of 96%. These results show that GTB can be applied as adsorbent for decontamination of wastewaters containing methylene blue.

Preparation of carbonaceous materials from pyrolysis of chicken bones and its application for fuchsine adsorption

Activated carbon and biochar were obtained from chicken bone (CB), characterized, and applied to remove basic fuchsine from aqueous media. The adsorbent dosage and pH effects were studied, as well as kinetic, equilibrium, and thermodynamic curves were constructed. The values of BET surface area and total pore volume were 108.94 m2 g-1 and 0.219 cm3 g-1 for the activated carbon and, 18.72 m2 g-1 and 0.075 cm3 g-1 for the biochar. The dye removal percentages were 93.63 and 55.38% when 2.5 g L-1 of activated carbon and biochar were used, respectively. The adsorption was favored using 0.5 g L-1 of adsorbent and pH of 7.0. Adsorption kinetics was well represented by the pseudo-second-order model. Langmuir model was the best to represent the equilibrium. Maximum adsorption capacity was 260.8 mg g-1, obtained using activated carbon. The process was endothermic, favorable, and spontaneous. Results showed that alternative carbonaceous materials can be obtained from chicken bones and used as adsorbents to treat colored effluents containing fuchsine.

The addition of a quaternary group in biopolymeric material increases the adsorptive capacity of Acid Blue 25 textile dye

The quaternization of chitosan molecules creates materials with high adsorptive capacity towards textile dyes, which renders them capable of rapidly removing such dyes from a solution. In this study, a novel material was synthesized in bead form to adsorb the Acid Blue 25 textile dye. The adsorption isotherms, kinetics, and thermodynamics of this new material were investigated. The beads were further characterized by FT-IR and SEM studies, as well as their rheological behavior. Bioassays with Daphnia similis analyzed the toxicity of the dye before and after treatments. The Freundlich isotherm model fitted to all the adsorption data in a pH range from 2.50 to 8.50. Kinetic studies showed that adsorption was ruled by an intraparticle diffusion process and reached equilibrium in 270 min, as 39.527 μg mg^-1 of dye was sorbed to the beads. Thermodynamic studies showed that adsorption was a spontaneous and endothermic process. Thermodynamics also confirmed that the adsorption was proportionally influenced by higher temperatures. The FT-IR spectroscopy identified the adsorbate/adsorbent binding sites, thus confirming the occurrence of chemisorption. Post-treatment bioassays found a significant decrease in toxicity, obtaining just 10% of D. similis mortality after adsorption treatments. Therefore, the synthesized beads from this research can potentially be applied to the treatment of textile effluents.

Potential of Cedrella fissilis bark as an adsorbent for the removal of red 97 dye from aqueous effluents

Cedar bark (Cedrella fissilis), a waste from wood processing, was evaluated as an adsorbent for the removal of red 97 dye from effluents. The material exhibited an amorphous structure, irregular surface, and was mainly composed of lignin and holocellulose. The adsorption was favored at pH 2.0. The general order model was most suitable for describing the experimental kinetic data, being the equilibrium reached in around 30 min. The isotherm experiments were better described by the Langmuir model. The maximum adsorption capacity was 422.87 mg g^-1 at 328 K. The values of standard Gibbs free energy change (ΔG⁰) were from - 21 to - 26 kJ mol^-1, indicating a spontaneous and favorable process. The enthalpy change (ΔH⁰) was 18.98 kJ mol^-1, indicating an endothermic process. From the fixed bed adsorption experiment, an inclined breakthrough curve was found, with a mass transfer zone of 5.36 cm and a breakthrough time of 329 min. Cedar bark was able to treat a simulated effluent attaining color removal of 86.6%. These findings indicated that cedar bark has the potential to be applied as a low-cost adsorbent for the treatment of colored effluents in batch and continuous adsorption systems.

Biosorption of crystal violet dye using inactive biomass of the fungus Diaporthe schini

An inactive biomass of a new fungus recently discovered, Diaporthe schini, was evaluated for the biosorption of crystal violet (CV) in simulated textile effluents. The characterization assays were performed using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and N₂ adsorption/desorption isotherms. The influences of pH and biosorbent dosage on the biosorption capacity were evaluated. Kinetics, equilibrium and thermodynamic studies were also carried out. Characterization techniques showed an amorphous biosorbent, with a rough surface containing irregular particles and surface area of 6.5 m² g^-1. The most adequate values of pH and biosorbent dosage were 7.5 and 0.4 g L^-1, respectively. The Elovich kinetic model and the Sips equilibrium model were suitable to fit the experimental data. The biosorption capacity increased with temperature, reaching a maximum biosorption capacity of 642.3 mg g^-1 at 328 K. The biosorption was a spontaneous and endothermic process. Diaporthe schini inactive biomass was an interesting biosorbent to treat colored effluents, presenting efficiency of 87% in the decolorization of a simulated dye house effluent.

Application of polyaniline-based adsorbents for dye removal from water and wastewater-a review

Several industries release varying concentration of dye-laden effluent with substantial negative consequences for any receiving environmental compartment. The control of water pollution and tighter restriction on wastewater discharge directly into the environment to reduce the potential ecotoxicological effect of dyes is forcing processors to retreat and reuse process water and chemicals. Among the different available technologies, the adsorption process has been recognized to be one of the finest and cost-effective wastewater treatment technologies. Various adsorbents have been utilized to remove toxic dyes from water and wastewater. Here, we review the application of polyaniline-based polymeric adsorbent for the adsorption of dyes which have been received considerable attention. To date, various modifications of polyaniline have been explored to improve the adsorption properties. Review on the application of polyaniline for adsorption of dyes has not been present till date. This article provides relevant literature on the application of various polyaniline composites for removing dyes, and their adsorption capacities with their experimental conditions have been compiled. It is evident from the literature survey that polyaniline provides a better opportunity for scientists for the effective removal of various dye.

Potential of Araucaria angustifolia bark as adsorbent to remove Gentian Violet dye from aqueous effluents

Araucaria angustifolia bark (AA-bark), a waste generated in wood processing, was evaluated as a potential adsorbent to remove Gentian Violet (GV) dye from aqueous solutions. The AA-bark presented an amorphous structure with irregular surface and was composed mainly of lignin and holocellulose. These characteristics indicated that the adsorbent contains available sites to accommodate the dye molecules. The GV adsorption on AA-bark was favored at pH 8.0 with adsorbent dosage of 0.80 g L^-1. Pseudo-nth order model was adequate to represent the adsorption kinetics of GV on AA-bark. A fast adsorption rate was verified, with the equilibrium being attained within 30 min. Equilibrium data were well represented by the Langmuir model. The maximum adsorption capacity was 305.3 mg g^-1. Adsorption was spontaneous, favorable and endothermic. AA-bark was able to treat a simulated dye house effluent, reaching color removal values of 80%. An excellent performance was found in fixed bed experiments, where the length of the mass transfer zone was only 5.38 cm and the breakthrough time was 138.5 h. AA-bark can be regenerated two times using HNO₃ 0.5 mol L^-1. AA-bark can be used as a low-cost material to treat colored effluents in batch and fixed bed adsorption systems.

Anomalocardia brasiliana shellfish shells as a novel and ecofriendly adsorbent of Nylosan Brilliant Blue acid dye

Malacoculture waste (Anomalocardia brasiliana) shellfish shells (ABSS) were evaluated as adsorbents of Nylosan Brilliant Blue (NBB) acid dye. The ABSS were thermally activated at 1,000 °C for 10 h and then characterized by Fourier-transform infrared spectroscopy, analysis of specific surface area (BET), X-ray diffraction (XRD), and scanning electron microscopy. Point of zero charge (PZC) analysis of ABSS verified pH_PZC 13.0. The study of kinetics showed that the pseudo-second-order model fit the experimental data best and the system reached equilibrium within 5 min. Adsorption isotherms followed the Langmuir-Freundlich isotherm and ABSS reached an outstanding maximum adsorption capacity of 405 mg·g^-1 under the following optimum conditions: pH 12.4, 303 K, 450 rpm, 2.0 g of adsorbent, and 150 μm average particle size. These conditions were obtained after a previous statistical analysis of the variables. Enthalpy and Gibbs energy obtained in the thermodynamics experiments were -23.79 kJ·mol^-1 and -4.07 kJ·mol^-1, respectively. These parameters confirm that the process is exothermic, spontaneous, and indicative of the physical nature of the adsorption. The adsorption of NBB onto ABSS tended to be more favorable at a lower temperature. Low value of enthalpy suggested that weak binding forces, such as electrostatic interactions, govern the sorption mechanism. ABSS high availability in the environment, its low toxicity and high efficiency make it a promising ecofriendly adsorbent of textile dyes.