The Role of Peptides in the Design of Electrochemical Biosensors for Clinical Diagnostics

Detection strategies of infectious diseases via peptide-based electrochemical biosensors

Infectious diseases have threatened human life for as long as humankind has existed. One of the most crucial aspects of fighting against these infections is diagnosis to prevent disease spread. However, traditional diagnostic methods prove insufficient and time-consuming in the face of a pandemic. Therefore, studies focusing on detecting viruses causing these diseases have increased, with a particular emphasis on developing rapid, accurate, specific, user-friendly, and portable electrochemical biosensor systems. Peptides are used integral components in biosensor fabrication for several reasons, including various and adaptable synthesis protocols, long-term stability, and specificity. Here, we discuss peptide-based electrochemical biosensor systems that have been developed over the last decade for the detection of infectious diseases. In contrast to other reports on peptide-based biosensors, we have emphasized the following points i) the synthesis methods of peptides for biosensor applications, ii) biosensor fabrication approaches of peptide-based electrochemical biosensor systems, iii) the comparison of electrochemical biosensors with other peptide-based biosensor systems and the advantages and limitations of electrochemical biosensors, iv) the pros and cons of peptides compared to other biorecognition molecules in the detection of infectious diseases, v) different perspectives for future studies with the shortcomings of the systems developed in the past decade.

A novel magnetic ligand-based assay for the electrochemical determination of BRD4

The first magnetic ligand-based electrochemical assay aimed at the determination of BRD4 was developed and validated. BRD4 is an epigenetic regulator of great interest in oncology in relation to its overexpression observed in the pathogenesis of several cancer diseases. BRD4 also represents a major target for the development of innovative treatments aimed at protein inhibition or degradation. Despite the relevance of BRD4 both for diagnostics and therapeutic purposes, current methodologies for its determination are limited to commercial ELISA kits. We present a novel magnetic ligand-based assay for the electrochemical determination of BRD4. The developed assay is based on the use of a small synthetic fragment of the natural protein ligand for BRD4 as receptor, thus exploiting the intrinsic biological protein-protein recognition mechanism. In addition, the assay features the use of magnetic beads as immobilization platforms and peroxidase-conjugated monoclonal anti-BRD4 antibody for the generation of the electrochemical signal. The ligand-based assay shows outstanding performance in terms of rapidity, with results achievable in less than 20 min, no matrix effect when applied to human plasma or cell lysate samples, and excellent specificity. The proposed method exhibits a limit of detection of 2.66 nM and a response range tunable as a function of the amount of immobilized receptor. The developed ligand-based assay was successfully applied to the accurate determination of BRD4 in untreated cell lysates, as proven by the ELISA reference method. The good performance of the proposed bioassay for determination of BRD4 showed potential application of this strategy in convenient point-of-care testing.

Fabrication of a high-sensitivity electrochemical immunosensor by the oriented immobilization of engineered nanobody on nanofibrous membrane

A new type of label-free electrochemical immunosensor for the high-sensitivity determination of parathion was developed based on the oriented immobilization of nanobody (VHH9) on a gold nanoparticle-loaded polyvinyl alcohol/citric acid nanofiber membrane-modified electrode. The morphology characterization and assembly process of the modified materials were investigated using scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). Under the optimum conditions, the label-free electrochemical immunosensor for parathion exhibited a linear range of 0.0015-6400 ng/mL and a low detection limit of 0.48 pg/mL, the signal response of which was 10 times higher than that of the randomly immobilized VHH9. The immunosensor possessed high selectivity, good repeatability and reusability (keeping above 90% of its initial activity after repeating 8 times), and stability (remaining 90% after 9 weeks of storage). Finally, the average recoveries of parathion from food samples were 93.76-105.73% with the coefficient of variation being 2.65-6.85%, showing good correlation with UPLC (R2 = 0.9950). Therefore, our nanobody immobilization protocol is simple and effective and proves the potential to be utilized as a promising candidate for sensing platform.

The multifaceted role of proteases and modern analytical methods for investigation of their catalytic activity

We discuss the diverse functions of proteases in the context of their biotechnological and medical significance, as well as analytical approaches used to determine the functional activity of these enzymes. An insight into modern approaches to studying the kinetics and specificity of proteases, based on spectral (absorption, fluorescence), mass spectrometric, immunological, calorimetric, and electrochemical methods of analysis is given. We also examine in detail electrochemical systems for determining the activity and specificity of proteases. Particular attention is given to exploring innovative electrochemical systems based on the detection of the electrochemical oxidation signal of amino acid residues, thereby eliminating the need for extra redox labels in the process of peptide synthesis. In the review, we highlight the main prospects for the further development of electrochemical systems for the study of biotechnologically and medically significant proteases, which will enable the miniaturization of the analytical process for determining the catalytic activity of these enzymes.

The Future of Nanotechnology-Driven Electrochemical and Electrical Point-of-Care Devices and Diagnostic Tests

Point-of-care (POC) devices have become rising stars in the biosensing field, aiming at prognosis and diagnosis of diseases with a positive impact on the patient but also on healthcare and social care systems. Putting the patient at the center of interest requires the implementation of noninvasive technologies for collecting biofluids and the development of wearable platforms with integrated artificial intelligence-based tools for improved analytical accuracy and wireless readout technologies. Many electrical and electrochemical transducer technologies have been proposed for POC-based sensing, but several necessitate further development before being widely deployable. This review focuses on recent innovations in electrochemical and electrical biosensors and their growth opportunities for nanotechnology-driven multidisciplinary approaches. With a focus on analytical aspects to pave the way for future electrical/electrochemical diagnostics tests, current limitations and drawbacks as well as directions for future developments are highlighted.

Functional Interface for Glycoprotein Sensing: Focusing on Biosensors

Glycosylated proteins or glycoproteins make up a large family of glycoconjugates, and they participate in a variety of fundamental biological events. Glycoproteins have become important biomarkers in the diagnosis and treatment of a number of tumors. Biosensors are quite suitable for glycoprotein detection. The design and fabrication of a functional sensing interface play a crucial role in the biosensor construction to target glycoproteins. The functional interface, particularly receptors, typically determines the key characteristics of a biosensor, such as selectivity and sensitivity. Antibody, peptide, aptamer, boronic acid derivative, lectin, and molecularly imprinted polymer are all capable receptors for glycoprotein recognition, and each of these will be discussed. Most glycoproteins exist in low abundance, thus rendering signal amplification techniques indispensable. Nucleic acid-mediated and nanomaterial-mediated signal amplification for the detection of glycoproteins will be focused on herein. This review aims to highlight these different functional interfaces for glycoprotein sensing.

An enzyme-responsive hydrogel of ferrocene-grafted carboxymethyl chitosan as a soft electrochemical sensor for MMP-9 detection

Matrix metalloproteinase 9 (MMP-9) plays an important role in wound healing. However, overexpression of MMP-9 leads to the degradation of the newly formed extracellular matrix, which delays wound healing, ultimately leading to chronic wounds. Therefore, timely monitoring of the MMP-9 activity using simple, cost-effective methods is important to prevent the formation of chronic wounds. In this work, ferrocene-modified MMP-9 cleavage peptide (Fc-MG) modified carboxymethyl chitosan hydrogels were prepared as electrochemical biosensors. In the presence of MMP-9, the peptide chain is sheared, and the electrochemically active ferrocene segment is released. Therefore, analyzing the electrochemical activity of hydrogels using differential pulse voltammetry (DPV) can be used to determine MMP-9 activity. The results showed that the DPV peaks were correlated with the MMP-9 concentration in phosphate-buffered saline (PBS, pH 7.4) and Dulbecco's modified Eagle's medium (DMEM). Specifically, the corresponding coefficient of determination (R2) were 0.918 and 0.993. The limit of detections were 73.08 ng/mL and 131.71 ng/mL, respectively. Compared with the enzyme-linked immunosorbent assay, the hydrogel biosensor determined the concentration of MMP-9 in solution with simpler steps. This study demonstrates a novel strategy based on Fc-MG-modified hydrogels to monitor MMP-9 activity in cell secretion samples and shows the potential application in chronic wounds.

Nanoarchitectonics-based electrochemical aptasensors for highly efficient exosome detection

Exosomes, a type of extracellular vesicles, have attracted considerable attention due to their ability to provide valuable insights into the pathophysiological microenvironment of the cells from which they originate. This characteristic implicates their potential use as diagnostic disease biomarkers clinically, including cancer, infectious diseases, neurodegenerative disorders, and cardiovascular diseases. Aptasensors, which are electrochemical aptamers based biosensing devices, have emerged as a new class of powerful detection technology to conventional methods like ELISA and Western analysis, primarily because of their capability for high-performance bioanalysis. This review covers the current research landscape on the detection of exosomes utilizing nanoarchitectonics strategy for the development of electrochemical aptasensors. Strategies involving signal amplification and biofouling prevention are discussed, with an emphasis on nanoarchitectonics-based bio-interfaces, showcasing their potential to enhance sensitivity and selectivity through optimal conduction and mass transport properties. The ongoing challenges to broaden the clinical applications of these biosensors are also highlighted.

Breaking barriers in electrochemical biosensing using bioinspired peptide and phage probes

Electrochemical biosensing continues to advance tirelessly, overcoming barriers that have kept it from leaving research laboratories for many years. Among them, its compromised performance in complex biological matrices due to fouling or receptor stability issues, the limitations in determining toxic and small analytes, and its use, conditioned to the commercial availability of commercial receptors and the exploration of natural molecular interactions, deserved to be highlighted. To address these challenges, in addition to the intrinsic properties of electrochemical biosensing, its coupling with biomimetic materials has played a fundamental role, among which bioinspired phage and peptide probes stand out. The versatility in design and employment of these probes has opened an unimaginable plethora of possibilities for electrochemical biosensing, improving their performance far beyond the development of highly sensitive and selective devices. The state of the art offers robust electroanalytical biotools, capable of operating in complex samples and with exciting opportunities to discover and determine targets regardless of their toxicity and size, the commercial availability of bioreceptors, and prior knowledge of molecular interactions. With all this in mind, this review offers a panoramic, novel, and updated vision of both the tremendous advances and opportunities offered by the combination of electrochemical biosensors with bioinspired phage and peptide probes and the challenges and research efforts that are envisioned in the immediate future.

Peptide-Based Flavivirus Biosensors: From Cell Structure to Virological and Serological Detection Methods

In tropical and developing countries, mosquito-borne diseases by flaviviruses pose a serious threat to public health. Early detection is critical for preventing their spread, but conventional methods are time-consuming and require skilled technicians. Biosensors have been developed to address this issue, but cross-reactivity with other flaviviruses remains a challenge. Peptides are essentially biomaterials used in diagnostics that allow virological and serological techniques to identify flavivirus selectively. This biomaterial originated as a small protein consisting of two to 50 amino acid chains. They offer flexibility in chemical modification and can be easily synthesized and applied to living cells in the engineering process. Peptides could potentially be developed as robust, low-cost, sensitive, and selective receptors for detecting flaviviruses. However, modification and selection of the receptor agents are crucial to determine the effectiveness of binding between the targets and the receptors. This paper addresses two potential peptide nucleic acids (PNAs) and affinity peptides that can detect flavivirus from another target-based biosensor as well as the potential peptide behaviors of flaviviruses. The PNAs detect flaviviruses based on the nucleotide base sequence of the target's virological profile via Watson-Crick base pairing, while the affinity peptides sense the epitope or immunological profile of the targets. Recent developments in the functionalization of peptides for flavivirus biosensors are explored in this Review by division into electrochemical, optical, and other detection methods.

Electrochemical biosensors for pathogenic microorganisms detection based on recognition elements

The worldwide spread of pathogenic microorganisms poses a significant risk to human health. Electrochemical biosensors have emerged as dependable analytical tools for the point-of-care detection of pathogens and can effectively compensate for the limitations of conventional techniques. Real-time analysis, high throughput, portability, and rapidity make them pioneering tools for on-site detection of pathogens. Herein, this work comprehensively reviews the recent advances in electrochemical biosensors for pathogen detection, focusing on those based on the classification of recognition elements, and summarizes their principles, current challenges, and prospects. This review was conducted by a systematic search of PubMed and Web of Science databases to obtain relevant literature and construct a basic framework. A total of 171 publications were included after online screening and data extraction to obtain information of the research advances in electrochemical biosensors for pathogen detection. According to the findings, the research of electrochemical biosensors in pathogen detection has been increasing yearly in the past 3 years, which has a broad development prospect, but most of the biosensors have performance or economic limitations and are still in the primary stage. Therefore, significant research and funding are required to fuel the rapid development of electrochemical biosensors. The overview comprehensively evaluates the recent advances in different types of electrochemical biosensors utilized in pathogen detection, with a view to providing insights into future research directions in biosensors.

Advances in Electrochemical Biosensors for the Detection of Common Oral Diseases

Limiting and preventing oral diseases remains a major challenge to the health of populations around the world, so finding ways to detect early-stage diseases (e.g., caries, periodontal disease, and oral cancer) and aiding in their prevention has always been an important clinical treatment concept. The development and application of electrochemical detection technology can provide important support for the early detection and non-invasive diagnosis of oral diseases and make up for the shortcomings of traditional diagnostic methods, which are highly sensitive, non-invasive, cost-effective, and less labor-intensive. It detects specific disease markers in body fluids through electrochemical reactions, discovers early warning signals of diseases, and realizes rapid and reliable diagnosis. This paper comprehensively summarizes the development and application of electrochemical biosensors in the detection and diagnosis of common oral diseases in terms of application platforms, sensing types, and disease detection, and discusses the challenges faced by electrochemical biosensors in the detection of oral diseases as well as the great prospects for future applications, in the hope of providing important insights for the future development of electrochemical biosensors for the early detection of oral diseases.

Self-Assembly of a Novel Pentapeptide into Hydrogelated Dendritic Architecture: Synthesis, Properties, Molecular Docking and Prospective Applications

Currently, ultrashort oligopeptides consisting of fewer than eight amino acids represent a cutting-edge frontier in materials science, particularly in the realm of hydrogel formation. By employing solid-phase synthesis with the Fmoc/tBu approach, a novel pentapeptide, FEYNF-NH2, was designed, inspired by a previously studied sequence chosen from hen egg-white lysozyme (FESNF-NH2). Qualitative peptide analysis was based on reverse-phase high performance liquid chromatography (RP-HPLC), while further purification was accomplished using solid-phase extraction (SPE). Exact molecular ion confirmation was achieved by matrix-assisted laser desorption-ionization mass spectrometry (MALDI-ToF MS) using two different matrices (HCCA and DHB). Additionally, the molecular ion of interest was subjected to tandem mass spectrometry (MS/MS) employing collision-induced dissociation (CID) to confirm the synthesized peptide structure. A combination of research techniques, including Fourier-transform infrared spectroscopy (FTIR), fluorescence analysis, transmission electron microscopy, polarized light microscopy, and Congo red staining assay, were carefully employed to glean valuable insights into the self-assembly phenomena and gelation process of the modified FEYNF-NH2 peptide. Furthermore, molecular docking simulations were conducted to deepen our understanding of the mechanisms underlying the pentapeptide's supramolecular assembly formation and intermolecular interactions. Our study provides potential insights into amyloid research and proposes a novel peptide for advancements in materials science. In this regard, in silico studies were performed to explore the FEYNF peptide's ability to form polyplexes.

In-silico selection of peptides for the recognition of imidacloprid

The sensitive detection of pesticides using low-cost receptors designed from peptides can widen their uses in the environmental surveillance for emerging pollutants. In-silico selection of peptides can help accelerate the design of receptor sequence banks for a given target of interest. In this work, we started from Lymnaea stagnalis acetylcholine-binding protein Q55R mutant receptor-imidacloprid complex, available in the PDB databank, to select three primary short peptides (YSP09, DMR12, WQW13 respectively having 9, 12 and 13 amino acids (AA) in length) from the pesticide interacting zones with the A, B and C chains of the nicotinic receptor. Using molecular docking and molecular dynamics (MD) simulations, we showed that the three peptides can form complexes with the target imidacloprid, having energies close to that obtained from a reference RNR12 peptide. Combination of these peptides allowed preparing a new set of longer peptides (YSM21, PSM22, PSW31 and WQA34) that have higher stability and affinity as shown by the MM-PBSA calculations. In particular, the WQA34 peptide displayed an average binding free energy of -6.44±0.27 kcal/mol, which is three times higher than that of the reference RNR12 peptide (-2.29±0.25 kcal/mol) and formed a stable complex with imidacloprid. Furthermore, the dissociation constants (Kd), calculated from the binding free energy, showed that WQA32 (40 μM) has three orders of magnitude lower Kd than the reference RNR12 peptide (3.4 × 104 μM). Docking and RMSD scores showed that the WQA34 peptide is potentially selective to the target imidacloprid with respect to acetamiprid and clothianidin. Therefore, this peptide can be used in wet-lab experiments to prepare a biosensor to selectively detect imidacloprid.

Achieving high hybridization density at DNA biosensor surfaces using branched spacer and click chemistry

The COVID-19 pandemic has highlighted the necessity to develop fast, highly sensitive and selective virus detection methods. Surface-based DNA-biosensors are interesting candidates for this purpose. Functionalization of solid substrates with DNA must be precisely controlled to achieve the required accuracy and sensitivity. In particular, achieving high hybridization density at the sensing surface is a prerequisite to reach a low limit of detection. We herein describe a strategy based on peptides as anchoring units to immobilize DNA probes at the surface of borosilicate slides. While the coating pathway involves copper-catalyzed click chemistry, a copper-free variation is also reported. The resulting biochips display a high hybridization density (2.9 pmol per cm2) with their targeted gene sequences.

Exploiting the Features of Short Peptides to Recognize Specific Cell Surface Markers

Antibodies are the macromolecules of choice to ensure specific recognition of biomarkers in biological assays. However, they present a range of shortfalls including a relatively high production cost and limited tissue penetration. Peptides are relatively small molecules able to reproduce sequences of highly specific paratopes and, although they have less biospecificity than antibodies, they offer advantages like ease of synthesis, modifications of their amino acid sequences and tagging with fluorophores and other molecules required for detection. This work presents a strategy to design peptide sequences able to recognize the CD44 hyaluronic acid receptor present in the plasmalemma of a range of cells including human bone marrow stromal mesenchymal cells. The protocol of identification of the optimal amino acid sequence was based on the combination of rational design and in silico methodologies. This protocol led to the identification of two peptide sequences which were synthesized and tested on human bone marrow mesenchymal stromal cells (hBM-MSCs) for their ability to ensure specific binding to the CD44 receptor. Of the two peptides, one binds CD44 with sensitivity and selectivity, thus proving its potential to be used as a suitable alternative to this antibody in conventional immunostaining. In the context of regenerative medicine, the availability of this peptide could be harnessed to functionalize tissue engineering scaffolds to anchor stem cells as well as to be integrated into systems such as cell sorters to efficiently isolate MSCs from biological samples including various cell subpopulations. The data here reported can represent a model for developing peptide sequences able to recognize hBM-MSCs and other types of cells and for their integration in a range of biomedical applications.

Electrochemical Affinity Biosensors: Pervasive Devices with Exciting Alliances and Horizons Ahead

Electrochemical affinity biosensors are evolving at breakneck speed, strengthening and colonizing more and more niches and drawing unimaginable roadmaps that increasingly make them protagonists of our daily lives. They achieve this by combining their intrinsic attributes with those acquired by leveraging the significant advances that occurred in (nano)materials technology, bio(nano)materials and nature-inspired receptors, gene editing and amplification technologies, and signal detection and processing techniques. The aim of this Perspective is to provide, with the support of recent representative and illustrative literature, an updated and critical view of the repertoire of opportunities, innovations, and applications offered by electrochemical affinity biosensors fueled by the key alliances indicated. In addition, the imminent challenges that these biodevices must face and the new directions in which they are envisioned as key players are discussed.

Designing Quantum Capacitive Peptide Interfaces for Electroanalytical Applications

Redox-active moieties assembled on metallic interfaces have been shown to follow quantum mechanical rules, where the quantum capacitance of the interface (directly associated with the electronic structure of the redox-active moieties) plays a key role in the electron transfer dynamics of the interface. Modifying these interfaces with biological receptors has significant advantages (simplifying molecular diagnostics methods, reducing size, time, and cost while maintaining high sensitivity), enabling the fabrication of miniaturized electroanalytical devices that can compete with traditional ELISA and RT-PCR benchtop assay methods. Owing to their intrinsic characteristics, the use of peptide-based redox-active moieties is a promising chemical route for modifying metallic surfaces, resulting in a high quantum capacitive signal sensitivity. In the present work, different ferrocene-tagged peptides with a structure of Fc-Glu-XX-XX-Cys-NH2 (XX = serine, phenylalanine, glycine) were used to form self-assembled monolayers on gold. The feasibility of using these interfaces in an electroanalytical assay was verified by detecting the NS1 DENV (Dengue Virus) biomarker to compare the efficiency of peptide structures for biosensing purposes. Parameters such as the formal potential of the interface, normalized electronic density of states (DOS), quantum capacitance, and electron transfer rate constants were obtained for Ser-, Phe-, and Gly-peptides. The Gly-peptide structure presented the highest analytical performance for sensing NS1 with a sensitivity of 5.6% per decade and the lowest LOD (1.4 ng mL-1) and LOQ (2.6 ng mL-1), followed by Phe-peptide, whereas Ser-peptide had the lowest performance. This work demonstrates that the use of peptides to fabricate a self-assembled monolayer as a biosensor component has advantages for low-cost point-of-care diagnostics. It also shows that the performance of the sensing interface depends strongly on how the chemistry of the surface is designed as a whole, not only on the redox-active group.

Advancements in Biosensors Based on the Assembles of Small Organic Molecules and Peptides

Over the past few decades, molecular self-assembly has witnessed tremendous progress in a variety of biosensing and biomedical applications. In particular, self-assembled nanostructures of small organic molecules and peptides with intriguing characteristics (e.g., structure tailoring, facile processability, and excellent biocompatibility) have shown outstanding potential in the development of various biosensors. In this review, we introduced the unique properties of self-assembled nanostructures with small organic molecules and peptides for biosensing applications. We first discussed the applications of such nanostructures in electrochemical biosensors as electrode supports for enzymes and cells and as signal labels with a large number of electroactive units for signal amplification. Secondly, the utilization of fluorescent nanomaterials by self-assembled dyes or peptides was introduced. Thereinto, typical examples based on target-responsive aggregation-induced emission and decomposition-induced fluorescent enhancement were discussed. Finally, the applications of self-assembled nanomaterials in the colorimetric assays were summarized. We also briefly addressed the challenges and future prospects of biosensors based on self-assembled nanostructures.

Highly sensitive electrochemical peptide-based biosensor for marine biotoxin detection using a bimetallic platinum and ruthenium nanoparticle-tethered metal-organic framework modified electrode

Saxitoxin (STX) is a highly toxic small-molecule cyanotoxin that is water-soluble, stable in acidic media, and thermostable. STX is hazardous to human health and the environment in ocean, thus it is an important to detect it at very low concentrations. Herein, we developed an electrochemical peptide-based biosensor for the trace detection of STX in different sample matrix utilizing differential pulse voltammetry (DPV) signal. We synthesized the nanocomposite of zeolitic imidazolate framework-67 (ZIF-67) decorated bimetallic platinum (Pt) and ruthenium (Ru) nanoparticles (Pt-Ru@C/ZIF-67) using impregnation method. The nanocomposite modified with screen-printed electrode (SPE) was subsequently used to detect STX in the range of 1-1,000 ng mL^-1, with a detection limit (LOD) of 26.7 pg mL^-1. The developed peptide-based biosensor is highly selective and sensitive towards STX detection, thus it represents a promising strategy for the development of novel portable bioassay for monitoring various hazardous molecules in aquatic food chains.

Label-Free Electrochemical Methods for Disease Detection

Label-free electrochemical biosensing leverages the advantages of label-free techniques, low cost, and fewer user steps, with the sensitivity and portability of electrochemical analysis. In this review, we identify four label-free electrochemical biosensing mechanisms: (a) blocking the electrode surface, (b) allowing greater access to the electrode surface, (c) changing the intercalation or electrostatic affinity of a redox probe to a biorecognition unit, and (d) modulating ion or electron transport properties due to conformational and surface charge changes. Each mechanism is described, recent advancements are summarized, and relative advantages and disadvantages of the techniques are discussed. Furthermore, two avenues for gaining further diagnostic information from label-free electrochemical biosensors, through multiplex analysis and incorporating machine learning, are examined.

Quasi-prime peptides: identification of the shortest peptide sequences unique to a species

Determining the organisms present in a biosample has many important applications in agriculture, wildlife conservation, and healthcare. Here, we develop a universal fingerprint based on the identification of short peptides that are unique to a specific organism. We define quasi-prime peptides as sequences that are found in only one species, and we analyzed proteomes from 21 875 species, from viruses to humans, and annotated the smallest peptide kmer sequences that are unique to a species and absent from all other proteomes. We also perform simulations across all reference proteomes and observe a lower than expected number of peptide kmers across species and taxonomies, indicating an enrichment for nullpeptides, sequences absent from a proteome. For humans, we find that quasi-primes are found in genes enriched for specific gene ontology terms, including proteasome and ATP and GTP catalysis. We also provide a set of quasi-prime peptides for a number of human pathogens and model organisms and further showcase its utility via two case studies for Mycobacterium tuberculosis and Vibrio cholerae, where we identify quasi-prime peptides in two transmembrane and extracellular proteins with relevance for pathogen detection. Our catalog of quasi-prime peptides provides the smallest unit of information that is specific to a single organism at the protein level, providing a versatile tool for species identification.

Gold-binding peptide as a selective layer for electrochemical detection of SARS-CoV-2 antibodies

Electrochemical immunosensors are excellent alternatives to prepare portable platforms used for rapid and inexpensive diagnostic of infectious diseases such as the recently emerged COVID-19. Incorporating synthetic peptides as selective recognition layers combined with nanomaterials such as gold nanoparticles (AuNPs) can significantly enhance the analytical performance of immunosensors. In the present study, an electrochemical immunosensor based on solid-binding peptide was built and evaluated towards SARS-CoV-2 Anti-S antibodies detection. The peptide used as recognition site has two important portions: one based on the viral receptor binding domain (RBD), capable of recognizing antibodies of the spike protein (Anti-S), and another suitable for interacting with gold nanoparticles. Gold-binding peptide (Pept/AuNP) dispersion was used directly to modify a screen-printed carbon electrode (SPE). The voltammetric behavior of the [Fe(CN)₆]^3-/4- probe after every construction and detection step was recorded using cyclic voltammetry by assessing the stability of the Pept/AuNP as a recognition layer onto the electrode surface. Differential pulse voltammetry was used as a detection technique, and a linear working range from 75 ng mL^-1 to 15 μg mL^-1 was established, with 1.059 μA dec^-1 of sensitivity and R² = 0.984. The response selectivity against SARS-CoV-2 Anti-S antibodies was investigated in presence of concomitant species. The immunosensor was used to detect SARS-CoV-2 Anti-spike protein (Anti-S) antibodies in human serum samples, successfully differentiating between negative and positive responses of samples at a 95% confidence level. Therefore, the gold-binding peptide is a promising tool to be applied as a selective layer for antibody detection.

Electrochemical biosensor for trypsin activity assay based on cleavage of immobilized tyrosine-containing peptide

In this work, we proposed a biosensor for trypsin proteolytic activity assay using immobilization of model peptides on screen-printed electrodes (SPE) modified with gold nanoparticles (AuNPs) prepared by electrosynthetic method. Sensing of proteolytic activity was based on electrochemical oxidation of tyrosine residues of peptides. We designed peptides containing N-terminal cysteine residue for immobilization on an SPE, modified with gold nanoparticles, trypsin-specific cleavage site and tyrosine residue as a redox label. The peptides were immobilized on SPE by formation of chemical bonds between mercapto groups of the N-terminal cysteine residues and AuNPs. After the incubation with trypsin, time-dependent cleavage of the immobilized peptides was observed by decline in tyrosine electrochemical oxidation signal. The kinetic parameters of trypsin, such as the catalytic constant (k_cat), the Michaelis constant (K_M) and the catalytic efficiency (k_cat/K_M), toward the CGGGRYR peptide were determined as 0.33 ± 0.01 min^-1, 198 ± 24 nM and 0.0016 min^-1 nM^-1, respectively. Using the developed biosensor, we demonstrated the possibility of analysis of trypsin specificity toward the peptides with amino acid residues disrupting proteolysis. Further, we designed the peptides with proline or glutamic acid residues after the cleavage site (CGGRPYR and CGGREYR), and trypsin had reduced activity toward both of them according to the existing knowledge of the enzyme specificity. The developed biosensor system allows one to perform a comparative analysis of the protease steady-state kinetic parameters and specificity toward model peptides with different amino acid sequences.

Microbial nanowires with genetically modified peptide ligands to sustainably fabricate electronic sensing devices

Nanowires have substantial potential as the sensor component in electronic sensing devices. However, surface functionalization of traditional nanowire and nanotube materials with short peptides that increase sensor selectivity and sensitivity requires complex chemistries with toxic reagents. In contrast, microorganisms can assemble pilin monomers into protein nanowires with intrinsic conductivity from renewable feedstocks, yielding an electronic material that is robust and stable in applications, but also biodegradable. Here we report that the sensitivity and selectivity of protein nanowire-based sensors can be modified with a simple plug and play genetic approach in which a short peptide sequence, designed to bind the analyte of interest, is incorporated into the pilin protein that is microbially assembled into nanowires. We employed a scalable Escherichia coli chassis to fabricate protein nanowires that displayed either a peptide previously demonstrated to effectively bind ammonia, or a peptide known to bind acetic acid. Sensors comprised of thin films of the nanowires amended with the ammonia-specific peptide had a ca. 100-fold greater response to ammonia than sensors made with unmodified protein nanowires. Protein nanowires with the peptide that binds acetic acid yielded a 4-fold higher response than nanowires without the peptide. The protein nanowire-based sensors had greater responses than previously reported sensors fabricated with other nanomaterials. The results demonstrate that protein nanowires with enhanced sensor response for analytes of interest can be fabricated with a flexible genetic strategy that sustainably eliminates the energy, environmental, and health concerns associated with other common nanomaterials.

Sensitive biosensors based on topological insulator Bi2Se3 and peptide

In this work, we designed a facile and label-free electrochemical biosensor based on intrinsic topological insulator (TI) Bi₂Se₃ and peptide for the detection of immune checkpoint molecules. With topological protection, Bi₂Se₃ could have robust surface states with low electronic noise, which was beneficial for the stable and sensitive electron transport between electrode and electrolyte interface. The peptides are easily synthesized and chemically modified, and have good biocompatibility and bioavailability, which is a suitable candidate as the recognition units for immune checkpoint molecules. Therefore, the peptide/Bi₂Se₃ was developed as a suitable working electrode for the electrochemical biosensor. The basic performance of the designed peptide/Bi₂Se₃ biosensor was investigated to determine the Anti-HA Tag Antibody and PD-L1 molecules. The linear detection range was from 3.6 × 10^-10 mg mL^-1 to 3.6 × 10^-5 mg mL^-1, and the detection limit was 1.07 × 10^-11 mg mL^-1. Moreover, the biosensor also displayed good selectivity and stability.

Using a Single Peptide to Electrochemically Sense Multiple Kinases

Kinases are responsible for regulating cellular and physiological processes, and abnormal kinase activity is associated with various diseases. Therefore, kinases are being used as biomarkers for disease and developing methods for their sensing is highly important. Usually more than one kinase is involved in phosphorylating a target protein. However, kinase detection methods usually detect the activity of only one specific kinase. Here we describe an electrochemical kinase sensing tool for the selective detection of two kinases using the same target peptide. We demonstrate the sensing of kinases ERK2 and PKCδ. This is based on a single sensing element, a peptide that contains two distinct phosphorylation sites of these two kinases. Reversibility experiments with alkaline phosphatase and reaction with the electrochemically active ferrocene-labeled ATP showed that the mechanism of sensing is by detecting the enzymatic phosphorylation. Our approach can be further utilized to develop devices for the detection of multiple kinases and can be expanded to other types of enzymes involved in disease.

Impedimetric Bacterial Detection Using Random Antimicrobial Peptide Mixtures

The biosensing of bacterial pathogens is of a high priority. Electrochemical biosensors are an important future tool for rapid bacteria detection. A monolayer of bacterial-binding peptides can serve as a recognition layer in such detection devices. Here, we explore the potential of random peptide mixtures (RPMs) composed of phenylalanine and lysine in random sequences and of controlled length, to form a monolayer that can be utilized for sensing. RPMs were found to assemble in a thin and diluted layer that attracts various bacteria. Faradaic electrochemical impedance spectroscopy was used with modified gold electrodes to measure the charge-transfer resistance (RCT) caused due to the binding of bacteria to RPMs. Pseudomonas aeruginosa was found to cause the most prominent increase in RCT compared to other model bacteria. We show that the combination of highly accessible antimicrobial RPMs and electrochemical analysis can be used to generate a new promising line of bacterial biosensors.

Practical tips and new trends in electrochemical biosensing of cancer-related extracellular vesicles

To tackle cancer and provide prompt diagnoses and prognoses, the constantly evolving biosensing field is continuously on the lookout for novel markers that can be non-invasively analysed. Extracellular vesicles (EVs) may represent a promising biomarker that also works as a source of biomarkers. The augmented cellular activity of cancerous cells leads to the production of higher numbers of EVs, which can give direct information on the disease due to the presence of general and cancer-specific surface-tethered molecules. Moreover, the intravesicular space is enriched with other molecules that can considerably help in the early detection of neoplasia. Even though EV-targeted research has indubitably received broad attention lately, there still is a wide lack of practical and effective quantitative procedures due to difficulties in pre-analytical and analytical phases. This review aims at providing an exhaustive outline of the recent progress in EV detection using electrochemical and photoelectrochemical biosensors, with a focus on handling approaches and trends in the selection of bioreceptors and molecular targets related to EVs that might guide researchers that are approaching such an unstandardised field.

Peptide-Based Materials That Exploit Metal Coordination

Metal-ion coordination has been widely exploited to control the supramolecular behavior of a variety of building blocks into functional materials. In particular, peptides offer great chemical diversity for metal-binding modes, combined with inherent biocompatibility and biodegradability that make them attractive especially for medicine, sensing, and environmental remediation. The focus of this review is the last 5 years' progress in this exciting field to conclude with an overview of the future directions that this research area is currently undertaking.

Threonine Phosphorylation of an Electrochemical Peptide-Based Sensor to Achieve Improved Uranyl Ion Binding Affinity

We have successfully designed a uranyl ion (U(VI)-specific peptide and used it in the fabrication of an electrochemical sensor. The 12-amino acid peptide sequence, (n) DKDGDGYIpTAAE (c), originates from calmodulin, a Ca(II)-binding protein, and contains a phosphothreonine that enhances the sequence's affinity for U(VI) over Ca(II). The sensing mechanism of this U(VI) sensor is similar to other electrochemical peptide-based sensors, which relies on the change in the flexibility of the peptide probe upon interacting with the target. The sensor was systematically characterized using alternating current voltammetry (ACV) and cyclic voltammetry. Its limit of detection was 50 nM, which is lower than the United States Environmental Protection Agency maximum contaminant level for uranium. The signal saturation time was ~40 min. In addition, it showed minimal cross-reactivity when tested against nine different metal ions, including Ca(II), Mg(II), Pb(II), Hg(II), Cu(II), Fe(II), Zn(II), Cd(II), and Cr(VI). Its reusability and ability to function in diluted aquifer and drinking water samples were further confirmed and validated. The response of the sensor fabricated with the same peptide sequence but with a nonphosphorylated threonine was also analyzed, substantiating the positive effects of threonine phosphorylation on U(VI) binding. This study places emphasis on strategic utilization of non-standard amino acids in the design of metal ion-chelating peptides, which will further diversify the types of peptide recognition elements available for metal ion sensing applications.

Progress in the Development of Biosensors Based on Peptide-Copper Coordination Interaction

Copper ions, as the active centers of natural enzymes, play an important role in many physiological processes. Copper ion-based catalysts which mimic the activity of enzymes have been widely used in the field of industrial catalysis and sensing devices. As an important class of small biological molecules, peptides have the advantages of easy synthesis, excellent biocompatibility, low toxicity, and good water solubility. The peptide-copper complexes exhibit the characteristics of low molecular weight, high tenability, and unique catalytic and photophysical properties. Biosensors with peptide-copper complexes as the signal probes have promising application prospects in environmental monitoring and biomedical analysis and diagnosis. In this review, we discussed the design and application of fluorescent, colorimetric and electrochemical biosensors based on the peptide-copper coordination interaction.

Sensitive Detection of Rosmarinic Acid Using Peptide-Modified Graphene Oxide Screen-Printed Carbon Electrode

Peptides have been used as components in biological analysis and fabrication of novel sensors due to several reasons, including well-known synthesis protocols, diverse structures, and acting as highly selective substrates for enzymes. Bio-conjugation strategies can provide a simple and efficient way to convert peptide-analyte interaction information into a measurable signal, which can be further used for the manufacture of new peptide-based biosensors. This paper describes the sensitive properties of a peptide-modified graphene oxide screen-printed carbon electrode for accurate and sensitive detection of a natural polyphenol antioxidant compound, namely rosmarinic acid. Glutaraldehyde was chosen as the cross-linking agent because it is able to bind nonspecifically to the peptide. We demonstrated that the strong interaction between the immobilized peptide on the surface of the sensor and rosmarinic acid favors the addition of rosmarinic acid on the surface of the electrode, leading to an efficient preconcentration that determines a high sensitivity of the sensor for the detection of rosmarinic acid. The experimental conditions were optimized using different pH values and different amounts of peptide to modify the sensor surface, so that its analytical performances were optimal for rosmarinic acid detection. By using cyclic voltammetry (CV) as a detection method, a very low detection limit (0.0966 μM) and a vast linearity domain, ranging from 0.1 µM to 3.20 µM, were obtained. The novelty of this work is the development of a novel peptide-based sensor with improved performance characteristics for the quantification of rosmarinic acid in cosmetic products of complex composition. The FTIR method was used to validate the voltammetric method results.

Bicyclic peptide-based assay for uPA cancer biomarker

The use of synthetic bioreceptors to develop biosensing platforms has been recently gaining momentum. This case study compares the performance of a biosensing platform for the human biomarker urokinase-type plasminogen activator (h-uPA) when using two bicyclic peptides (P₁ and P₂) with different affinities for the target protein. The bioreceptors P₁ and P₂ were immobilized on magnetic microbeads and tested within a sandwich-type affinity electrochemical assay. Apart from enabling h-uPA quantification at nanomolar levels (105.8 ng/mL for P₁ and 32.5 ng/mL for P₂), this case study showed the potential of synthetic bicyclic peptides applicability and how bioreceptor affinity can influence the performance of the final sensing platform.

Electrochemical nanobiosensors equipped with peptides: a review

Recent research in the field of electrochemical biosensors equipped with peptides and nanomaterials have been categorized, reviewed, and critically analyzed. Indeed, using these innovative biosensors can revolutionize biomedical diagnostics in the future. Saving lives, time, and money in this field will be considered as some main benefits of this type of diagnosis. Here, these biosensors have been categorized and evaluated in four main sections. In the first section, the focus is on investigating the types of electrochemical peptide-based nanobiosensors applied to detect pathogenic microorganisms, microbial toxins, and viruses. In the second section, due to the importance of rapid diagnosis and prognosis of various cancers, the electrochemical peptide-based nanobiosensors designed to detect cancer biomarkers have been reviewed and analyzed. In the third section, the electrochemical peptide-based nanobiosensors, which were applied to detect the essential and effective biomolecules in the various diseases, and health control, including enzymes, hormones, biomarkers, and other biomolecules, have been considered. Finally, using a comprehensive analysis, all the used elements in these biosensors have been presented as conceptual diagrams that can effectively guide researchers in future developments. The essential factors in evaluating and analyzing these electrochemical peptide-based nanobiosensors such as analyte, peptide sequence, functional groups interacted between the peptide sequences and other biosensing components, the applied nanomaterials, diagnostic techniques, detection range, and limit of detection have also been included. Other analyzable items such as the type of used redox marker and the location of the peptide sequence against the signal transducer were also considered.

Phage Display-Derived Peptide for the Specific Binding of SARS-CoV-2

Beginning from the end of 2019, the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic swept all over the world and is still afflicting the whole global population. Given that the vaccine-manufacturing ability is limited and the virus can evolve quickly, vaccination alone may not be able to end the pandemic, thus developing fast and accurate diagnoses and effective therapeutics will always be unmet needs. Phage display peptide library has been used in screening antigen-specific peptides for the invention of novel mimic receptors/ligands. Here, we report that a 12-mer phage display peptide library has been screened against the SARS-CoV-2 receptor-binding domain (RBD), and five of the screened peptides show binding ability with the RBD protein by the enzyme-linked immune sorbent assay. The surface plasmon resonance assay further demonstrates that peptide no. 1 can specifically bind to SARS-CoV-2 RBD with a binding affinity constant (K d) of 5.8 μM. Transmission electron microscopy coupled with a magnetic bead assay further confirms that the screened peptide can specifically bind the inactivated SARS-CoV-2 virus. This SARS-CoV-2-specific peptide holds great promise as a new bioreceptor/ligand for the rapid and accurate detection of SARS-CoV-2.

Veni, Vidi, Vici: Immobilized Peptide-Based Conjugates as Tools for Capture, Analysis, and Transformation

Analysis of peptide biomarkers of pathological states of the organism is often a serious challenge, due to a very complex composition of the cell and insufficient sensitivity of the current analytical methods (including mass spectrometry). One of the possible ways to overcome this problem is sample enrichment by capturing the selected components using a specific solid support. Another option is increasing the detectability of the desired compound by its selective tagging. Appropriately modified and immobilized peptides can be used for these purposes. In addition, they find application in studying the specificity and activity of proteolytic enzymes. Immobilized heterocyclic peptide conjugates may serve as metal ligands, to form complexes used as catalysts or analytical markers. In this review, we describe various applications of immobilized peptides, including selective capturing of cysteine-containing peptides, tagging of the carbonyl compounds to increase the sensitivity of their detection, enrichment of biological samples in deoxyfructosylated peptides, and fishing out of tyrosine–containing peptides by the formation of azo bond. Moreover, the use of the one-bead-one-compound peptide library for the analysis of substrate specificity and activity of caspases is described. Furthermore, the evolution of immobilization from the solid support used in peptide synthesis to nanocarriers is presented. Taken together, the examples presented here demonstrate immobilized peptides as a multifunctional tool, which can be successfully used to solve multiple analytical problems.