Removal of Copper Ions from Wastewater: A Review

Efficacy of anthocyanin, kaolinite and cabbage leaves-derived biochar for simultaneous removal of lead, copper and metoprolol from water

Simultaneous removal of toxic elements and pharmaceutical compounds at environmentally relevant concentrations in aqueous solution is challenging. Modification of biochar using environmental materials has attracted significant attention in wastewater treatment, while pristine biochar has several limitations in the simultaneous removal of Lead (Pb2+), Copper (Cu2+), and metoprolol. We investigated the efficacy of biochar composites using waste cabbage leaves-derived biochar with kaolinite, and anthocyanin for simultaneous removal of Pb2+, Cu2+, and metoprolol from water. Using ball milling, the surface area and functional groups of adsorbents were improved via breaking the biochar grains into ultrafine particles. Ball-milled biochar derived from waste cabbage leaves significantly increased Pb2+, Cu2+, and metoprolol adsorption by 105, 71, and 213%, respectively. Results of Brunauer Emmett Teller surface area, Fourier transform infrared and X-ray photoelectron spectroscopies showed that surface area of non-milled biochar improved nearly ten-fold following ball-milling, while several oxygen containing acidic functional groups also increased. The adsorbents resulted in high removal efficiency for Pb2+ (162.9 mg/g) and Cu2+ (48.5 mg/g) in ball milled-kaolinite composite biochar (BMKB) and 76.3 mg/g (metoprolol), respectively in ball milled-anthocyanin composite biochar (BMAB). The simultaneous sorption of Pb2+, Cu2+, and metoprolol in an aqueous solution to BMAB and BMKB, showed that the adsorption capacity followed the order of Pb2+ >Cu2+ > metoprolol in both types of ball-milled biochars. BMKB achieved a high adsorption capacity for Pb2+ and Cu2+ (59 mg/g and 50 mg/g), respectively, while BMAB exhibited an adsorption capacity 22.3 mg/g for metoprolol. It was postulated that sorption of Pb2+, Cu2+ and metoprolol involved multiple adsorption mechanisms namely surface complexation, π-π interaction, H-bond, pore filling, and ion bridging. The findings of this study revealed that ball milling is a potential technology in producing a highlyefficient adsorbent to remediate multi-contaminants in aqueous solution.

Scalable mesoporous biochars from bagasse waste for Cu (II) removal: Process optimisation, kinetics and techno-economic analysis

As the world faces the brink of climatological disaster, it is crucial to utilize all available resources to facilitate environmental remediation, especially by accommodating waste streams. Lignocellulosic waste residues can be transformed into mesoporous biochar structures with substantial pore capacity. While biochars are considered a method of carbon dioxide removal (CDR), they are in fact an environmental double-edged sword that can be used to extract metal ions from water bodies. Biochars possess high chemical affinities through chemisorption pathways that are tuneable to specific pH conditions. This work demonstrates how biochars can be enhanced to maximise their surface area and porosity for the removal of Cu (II) in solution. It was found that bagasse derived mesoporous biochars operate preferentially at high pH (basic conditions), with the 1.18 mKOH/mSCB material reaching 97.85% Cu (II) removal in 5 min. This result is in stark contrast with the majority of biochar adsorbents that are only effective at low pH (acidic conditions). As a result, the biochars produced in this work can be directly applied to ancestral landfill sites and carbonate-rich mine waters which are highly basic by nature, preventing further metal infiltration and reverse sullied water supplies. Furthermore, to assess the value in the use of biochars produced and applied in this way, a techno-economic assessment was carried out to determine the true cost of biochar synthesis, with possible routes for revenue post-Cu being removed from the biochar.

Copper Ion Removal by Adsorption Using Fly Ash-Based Geopolymers: Process Optimization Insights from Taguchi and ANOVA Statistical Methods

The present study aimed to use geopolymer materials synthesized from different fly ashes, which are promising for the adsorption of copper ions from aqueous solutions. The characterization of fly ashes and prepared adsorbents was performed by energy-dispersive X-ray spectroscopy (EDS) analysis, Brunauer-Emmett-Teller (BET) surface area analysis, and Scanning Electron Microscopy (SEM). Taguchi and ANOVA methods were used to predict the effect of different working parameters on copper ion removal by prepared geopolymers. Based on data obtained by the Taguchi method, it was found that the factor most influencing the adsorption process is the type of adsorbent used, followed by the solution pH, the reaction time, the adsorbent dose, and the initial copper ion concentration. The ANOVA results agree with the Taguchi method. The optimal conditions of the adsorption process were: fly ash C modified by direct activation with 2 M NaOH, at 70 °C for 4 h, solution pH of 5, initial pollutant concentration of 300 mg/L, 40 g/L adsorbent dose, and 120 min of reaction time. Copper ion removal efficiency was determined experimentally under optimal conditions, achieving a value of 99.71%.

Incorporation of copper ion promoted adsorption of anionic dye (Acid Yellow 36) by acrolein-crosslinked polyethyleneimine/chitosan hydrogel: Adsorption, dynamics, and mechanisms

In this study, a novel adsorbent, A-PEI/CS-Cu2+, was developed by crosslinking polyethyleneimine/chitosan hydrogel with acrolein and loading it with copper ions. The adsorption process of A-PEI/CS-Cu2+ on the anionic dye acid yellow 36 (AY36) was investigated by kinetic, isothermal and thermodynamic modeling. It was noteworthy that A-PEI/CS-Cu2+ exhibited rapid adsorption with a 90 % removal rate achieved within just 5 min, which was much faster than the adsorption rate of A-PEI/CS without load of copper ions and showed its potential for rapid adsorption applications. The maximum adsorption capacity for AY36 could reach up to 3114 mg g-1. In addition, the high concentration of saline wastewater was found to have almost no effect on the adsorption reaction in the salt effect test experiment. In five desorption-regeneration cycle experiments, the sample exhibited good recyclability and regeneration performance. The driving force of the adsorption process mainly originated from the electrostatic interaction, hydrogen bonding, and intermolecular interaction, in which the addition of copper ions led to the enhancement of the electrostatic interaction and chelation between A-PEI/CS-Cu2+ and AY36. Overall, the findings suggest the excellent potential of A-PEI/CS-Cu2+ for rapid and efficient adsorption, as well as its suitability for practical applications in wastewater treatment.

Chitosan/Poly(maleic acid-alt-vinyl acetate) Hydrogel Beads for the Removal of Cu2+ from Aqueous Solution

Covalent cross-linked hydrogels based on chitosan and poly(maleic acid-alt-vinyl acetate) were prepared as spherical beads. The structural modifications of the beads during the preparation steps (dropping in liquid nitrogen and lyophilization, thermal treatment, washing with water, and treatment with NaOH) were monitored by FT-IR spectroscopy. The hydrogel beads have a porous inner structure, as shown by SEM microscopy; moreover, they are stable in acidic and basic pH due to the covalent crosslinking. The swelling degree is strongly influenced by the pH since the beads possess ionizable amine and carboxylic groups. The binding capacity for Cu2+ ions was examined in batch mode as a function of sorbent composition, pH, contact time, and the initial concentration of Cu2+. The kinetic data were well-fitted with the pseudo-second-order kinetic, while the sorption equilibrium data were better fitted with Langmuir and Sips isotherms. The maximum equilibrium sorption capacity was higher for the beads obtained with a 3:1 molar ratio between the maleic copolymer and chitosan (142.4 mg Cu2+ g-1), compared with the beads obtained using a 1:1 molar ratio (103.7 mg Cu2+ g-1). The beads show a high degree of reusability since no notable decrease in the sorption capacity was observed after five consecutive sorption/desorption cycles.

Mitochondrial miR-12294-5p-Regulated Copper Exposure-Caused Mitochondrial-Dependent Ferroptosis by Targeted Inhibition of CISD1 in Chicken Hepatocytes

Copper (Cu) is a common trace element additive in animal and human foods, and excessive intake of Cu has been shown to cause hepatotoxicity, but the underlying mechanism remains unclear. Our previous research found that Cu exposure dramatically upregulated mitochondrial miR-12294-5p expression and confirmed its targeted inhibition of CISD1 expression in chicken hepatocytes. Thus, we aimed to explore the potential role of mitomiR-12294-5p/CISD1 axis in Cu exposure-resulted hepatotoxicity. Here, we observed that Cu exposure resulted in Cu accumulation and pathological injury in chicken livers. Moreover, we found that Cu exposure caused mitochondrial-dependent ferroptosis in chicken hepatocytes, which were prominent on the increased mitochondrial Fe2+ and mitochondrial lipid peroxidation, inhibited levels of CISD1, GPX4, DHODH, and IDH2, and also enhanced level of PTGS2. Notably, we identified that inhibition of mitomiR-2954 level effectively mitigated Cu-exposure-resulted mitochondrial Fe2+ accumulation and mitochondrial lipid peroxidation and prevented the development of mitochondrial-dependent ferroptosis. However, increasing the mitomiR-12294-5p expression considerably aggravated the influence of Cu on these indicators. Meanwhile, the overexpression of CISD1 effectively alleviated Cu-caused mitochondrial-dependent ferroptosis, while silent CISD1 eliminated the therapeutic role of mitomiR-12294-5p inhibitor. Overall, our findings indicated that mitomiR-12294-5p/CISD1 axis played a critical function in Cu-caused hepatotoxicity in chickens by regulating mitochondrial-dependent ferroptosis.

Facile Green Gamma Irradiation of Water Hyacinth Derived-Fluorescent Carbon Dots Functionalized Thiol Moiety for Metal Ion Detection

Fluorescent sensor-based carbon dots (CDs) have significantly developed for sensing metal ions because of their great physical and optical properties, including tunable fluorescence emission, high fluorescence quantum yield, high sensitivity, non-toxicity, and biocompatibility. In this research, a green synthetic approach via simple gamma irradiation for the carbon dot synthesis from water hyacinth was developed since water hyacinth has been classified as an invasive aquatic plant containing cellulose, hemicellulose, and lignin. The thiol moiety (SH) was further functionalized on the surface functional groups of CDs as the "turn-off" fluorescent sensor for metal ion detection. Fluorescence emission displayed a red shift from 451 to 548 nm when excited between 240 and 500 nm. The quantum yield of CDs-SH was elucidated to be 13%, with strong blue fluorescence emission under ultraviolet irridiation (365 nm), high photostability and no photobleaching. The limit of detection was determined at micromolar levels for Hg2+, Cu2+, and Fe3+. CDs-SH could be a real-time monitoring sensor for Hg2+ and Cu2+ as fluorescence quenching was observed within 2 min. Furthermore, paper test-strip based CDs-SH could be applied to detect these metal ions.

Development of an aptasensor for dibutyl phthalate detection and the elucidation of assay inhibition factors

We developed a fluorescence aptasensor (hereafter 'SG-aptasensor') using SYBR Green I, a newly truncated 20-mer aptamer, and probe DNA to detect dibutyl phthalate (DBP). The detection range of DBP was 0.1-100 ng L-1 with 0.08 ng L-1 as the limit of detection. To adapt the assay to environmental samples in the near future, possible inhibition factors (experimental and environmental) have been tested and reported. The experimental inhibitors included the incubation time, temperature, pH, and ionic strength. Consequently, temperature (2-25 °C) and pH (7.0-9.0) ranges did not significantly inhibit the assay. The incubation time required for sufficient reaction was at least 4 h, and a relative humidity <20% may have induced fluorescence quenching. Tris-HCl-based incubation buffer with excess ionic strength (more than 0.2 M NaCl) demonstrated an abnormal increase in fluorescence. Environmental inhibitors including cations (Mg2+, Ca2+, and Cu2+) and humic acids were tested. The fluorescence signal was significantly reduced (∼99%) by 100 mM Cu2+ compared to that by 0 mM Cu2+. In contrast, the reduction in fluorescence signal was marginal (<15%) when Mg2+ or Ca2+ ions were present. Inhibition of the assay was observed (∼28%) in the presence of 100 mg L-1 humic acids.

Recent Progress on the Adsorption of Heavy Metal Ions Pb(II) and Cu(II) from Wastewater

With the processes of industrialization and urbanization, heavy metal ion pollution has become a thorny problem in water systems. Among the various technologies developed for the removal of heavy metal ions, the adsorption method is widely studied by researchers and various nanomaterials with good adsorption performances have been prepared during the past decades. In this paper, a variety of novel nanomaterials with excellent adsorption performances for Pb(II) and Cu(II) reported in recent years are reviewed, such as carbon-based materials, clay mineral materials, zero-valent iron and their derivatives, MOFs, nanocomposites, etc. The novel nanomaterials with extremely high adsorption capacity, selectivity and particular nanostructures are summarized and introduced, along with their advantages and disadvantages. And, some future research priorities for the treatment of wastewater are also prospected.

Construction of a novel flavonol fluorescent probe for copper (II) ion detection and its application in actual samples

Copper is an essential trace element in the human body, and its level is directly related to many diseases. While the source of copper in human body is mainly intake from food, then the detection of copper ions (Cu2+) in food becomes crucial. Here, we synthesized a novel probe (E)-3-hydroxy-2-styryl-4H-benzo[h]chromen-4-one (NSHF) and explored the binding ability of NSHF for Cu2+ using nuclear magnetic resonance hydrogen spectroscopy (1H NMR), high-resolution mass spectrometry (HRMS), Job's plot method and density functional theory (DFT). NSHF shows the advantages of fast response time, good selectivity and high sensitivity for Cu2+. The fluorescence intensity ratio (F/F0) of NSHF shows a good linear relationship with the concentration of Cu2+ and the detection limit is 0.061 μM. NSHF was successfully applied to the detection of Cu2+ in real samples. In addition, a simple and convenient Cu2+ detection platform was constructed by combining NSHF with a smartphone and a UV lamp, which can realize the rapid detection of Cu2+. This work provides an effective tool for the real-time detection of Cu2+.

Application of fluidized bed homogeneous crystallization for simultaneous recovery of Fe(II) and Cu(II) as particles from wastewater

The mixture of copper and iron often results in materials with favorable properties. The material production processes involving these metals including electroplating produce hazardous wastewater. In this study, the Fluidized Bed Homogeneous Crystallization (FBHC) process was applied to treat iron and copper-containing wastewater. The initial iron copper particles were successfully recovered from synthetic wastewater with [Fe]0:[Cu]0 of 2:1, the total metal concentration of 3 mM, at effluent pH = 7.75 ± 0.75, with the upflow velocity (U) of 1.76 m/h. The agglomerates hardening process is a crucial step for initial particle synthesis. The SEM analysis reveals the spherical particle's densified crust and porous core. The particle formation mechanism which includes the formation of the nucleus, attachment of precipitate flakes, and densification of particles was proposed after microscopic observation. The initial particles synthesized were used to initiate the treatment of synthetic wastewater at the operating condition pH = 7.75 ± 0.5, [Fe]0:[Cu]0 of 2:1, the total metal concentration of 3 mM, [CO32-]0:[M]0 = 1.2:1, and U of 28.66 m/h which results in the total metal removal of 99% and crystallization ratio of 90% and 88% for iron and copper respectively. The conditions were then applied to treat electroplating wastewater and resulted in the total metal removal of 99% for both iron and copper and a crystallization ratio of 83% and 79% for iron and copper, respectively. The treatment provided advantages in terms of treating larger amounts of sludge while eliminating the need to provide seed thus yielding a higher purity of product.

Carboxymethyl-imidazolium O-vanillin Schiff base grafted into NH2-tagged MIL-101 (Cr) for effective removal of cupric ions from aqueous effluents

A novel adsorbent (MIL-CMIVSB) was fabricated by modification of H2N-MIL-101(Cr) with carboxymethyl-imidazolium O-vanillin Schiff base. The MIL-CMIVSB's physicochemical characteristics were examined using the pertinent characterization methods. NH2-MIL-101(Cr) has a BET surface area of 1492.4 m2g-1, while MIL-CMIVSB adsorbent had 1278.7 m2g-1. Batch adsorption experiments examined the MIL-CMIVSB's cupric ion adsorption capacity from aqueous solutions at different adsorbent doses (0.1-3 mg), pH (2.0-10.0), contact times (0-240 min), metal ion initial concentrations (10-300 mg/L), and temperatures (298-308 K). The optimum conditions were 1 mg/mL of MIL-CMIVSB adsorbent, 46 min adsorption time, pH 7, 100 ppm initial cupric ion concentration, and 303 K temperature. MIL-CMIVSB effectively and selectively removes cupric ions with an adsorption capability of 359.05 ± 12.06 mg/g. The nonlinear Liu isotherm governed Cu(II) sorption performance on MIL-CMIVSB (KL = 0.257 ± 0.01 mg/g, R2 = 0.99892) and pseudo-2nd-order kinetically (k2 = 0.00116 × 10-4 g/mg min, R2 = 0.99721).

Enhancing copper and lead adsorption in water by in-situ generation of calcium carbonate on alginate/chitosan biocomposite surfaces

Chitosan (CS) and sodium alginate (SA)-based biocomposites (CSA) were prepared with the in-situ generation of Calcium Carbonate (CSAX_Ca) through a simple, straightforward, economical, and eco-friendly procedure. Different drying conditions (X) were tested to achieve suitable structural and surface characteristics to enhance adsorption capacity: freeze-dried (L), vacuum-dried with methanol (M), and freeze-dried + vacuum-dried with methanol (LM). Temperature and adsorbent dosage effects on the adsorption capacity of Cu2+ or Pb2+ were examined. Results showed that the higher-yielding biocomposite (CSALM_Ca) exhibited rapid adsorption and good diffusion properties, achieving removal above 90 % within contaminant initial concentration ranges of 10-100 mg/L. At 35 °C, a pseudo-second-order kinetic and the Langmuir model effectively described kinetics and isotherms, revealing maximum adsorption (qe, max) of 429 mgCu2+/L and 1742 mgPb2+/g. Characterization through FTIR, XRD, and SEM of the as-prepared adsorbents confirmed the presence of CaCO3 in vaterite and calcite forms and the influence of drying conditions on the material morphology. Post-adsorption material characterization, in combination with adsorption findings, revealed chemisorption processes involving Ca2+ ion exchange for Cu2+ or Pb2+, resulting in surface-insoluble compounds. The best-performing material showed that after three reuse cycles, the removal of Cu2+ and Pb2+ decreased to 75 % and 62 %, respectively.

Preparation of a Porous Geopolymer (SPG) to be Used as an Adsorbent for Cu2+ Removal

A porous geopolymer was synthesized using steel slag (accounting for 71.6 wt %) with the aim of effectively removing Cu2+ ions. The chemical composition and microstructure of this material were investigated using X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscope analysis, and BET method. The effects of H2O2 doping, H2O doping, and the curing temperature on the properties of this porous geopolymer were systematically investigated. Subsequently, the adsorption behavior of the porous geopolymer toward Cu2+ was explored through static adsorption experiments. The findings reveal that there are a higher specific surface area and pore capacity for the porous geopolymer compared to the original steel slag, with a total porosity of 90.3%, compressive strength of 0.29 MPa, and volume water absorption rate of 69.4%. The adsorption capacity of this material toward Cu2+ is found to be 36.8 mg·g-1, which is slightly superior to that of commercial spherical 4A molecular sieves. The adsorption process follows the quasi-first-order kinetic model, while the isothermal adsorption conforms to the Freundlich model.

Heavy Metal Removal from Wastewater Using Poly(Gamma-Glutamic Acid)-Based Hydrogel

The removal of toxic heavy metal ions from wastewater is of great significance in the protection of the environment and human health. Poly(gamma-glutamic acid) (PGA) is a non-toxic, biodegradable, and highly water-soluble polymer possessing carboxyl and imino functional groups. Herein, water-insoluble PGA-based hydrogels were prepared, characterized, and investigated as heavy metal adsorbents. The prepared hydrogels were recyclable and exhibited good adsorption effects on heavy metal ions including Cu2+, Cr6+, and Zn2+. The effects of adsorption parameters including temperature, solution pH, initial concentration of metal ions, and contact time on the adsorption capacity of the hydrogel for Cu2+ were investigated. The adsorption was a spontaneous and exothermic process. The process followed the pseudo-first-order kinetic model and Langmuir isotherm model, implying a physical and monolayer adsorption. The adsorption mechanisms investigation exhibited that Cu2+ adsorbed on the hydrogel via electrostatic interactions with anionic carboxylate groups of PGA in addition to the coordination interactions with the -NH groups. Importantly, the PGA hydrogel exhibited good reusability and the adsorption capability for Cu2+ remained high after five consecutive cycles. The properties of PGA hydrogel make it a potential candidate material for heavy metal ion removal in wastewater treatment.

Microbial strategies for copper pollution remediation: Mechanistic insights and recent advances

Environmental contamination is aninsistent concern affecting human health and the ecosystem. Wastewater, containing heavy metals from industrial activities, significantly contributes to escalating water pollution. These metals can bioaccumulate in food chains, posing health risks even at low concentrations. Copper (Cu), an essential micronutrient, becomes toxic at high levels. Activities like mining and fungicide use have led to Copper contamination in soil, water, and sediment beyond safe levels. Copper widely used in industries, demands restraint of heavy metal ion release into wastewater for ecosystem ultrafiltration, membrane filtration, nanofiltration, and reverse osmosis, combat heavy metal pollution, with emphasis on copper.Physical and chemical approaches are efficient, large-scale feasibility may have drawbackssuch as they are costly, result in the production of sludge. In contrast, bioremediation, microbial intervention offers eco-friendly solutions for copper-contaminated soil. Bacteria and fungi facilitate these bioremediation avenues as cost-effective alternatives. This review article emphasizes on physical, chemical, and biological methods for removal of copper from the wastewater as well asdetailing microorganism's mechanisms to mobilize or immobilize copper in wastewater and soil.

Resource utilization of wastepaper and bentonite: Cu(II) removal in the aqueous environment

Contamination of heavy metals has always been a pressing concern. The dry-wet alternately treated carboxymethylcellulose bentonite (DW-CB) was successfully prepared by intercalating bentonite (BT) with carboxymethyl cellulose (CMC) obtained by solvent processes using enzymatically digested wastepaper as cellulosic raw material, and the adsorption capacity of Cu2+ on DW-CB in aqueous solution was investigated. A 98.18 ± 2.31 % removal efficiency was achieved by 4 g/L of DW-CB after 8 h in a solution containing 100 mg/L of Cu2+, which were 4.1 times and 1.5 times of that of BT and adsorbent prepared without alternating dry-wet process, respectively. The introduction of -COOH groups during the preparation of DW-CB enhanced the electrostatic interaction between DW-CB and Cu2+, which was the main driving force for Cu2+ removal. The pseudo-first-order kinetic model and Langmuir model better described the adsorption process and adsorption capacity of Cu2+ on DW-CB. DW-CB still showed high removal of Cu2+ (19.61 ± 0.99 mg/g) in the presence of multiple metal ions, while exhibiting the potential for removal of Zn2+, Mg2+ and K+, especially Mg2+ (22.69 ± 1.48 mg/g). However, the interactions of organics with Cu2+ severely affected the removal of Cu2+ by DW-CB (removal efficiency: 17.90 ± 4.17 % - 95.33 ± 0.27 %). In this study, an adsorbent with high targeted adsorption of Cu2+ was prepared by utilizing wastepaper and BT, which broadened the way of wastepaper resource utilization and had good economic and social benefits.

Copper Stress Causes Shell Morphology Changes in Early Juvenile Anodonta woodiana Based on Geometric-Morphometric Analysis

In this study, the morphological characteristics of early juvenile shells of Anodonta woodiana, which were exposed to different concentrations of aqueous copper, were analyzed using 10 landmarks to determine morphological changes in the shells. Morphological changes mainly occurred at the top of the shell and front and back ends of the central axis. Stepwise discriminant analysis proved shape differences among experimental and control groups. The results of this study demonstrate for the first time that environmentally relevant copper concentrations cause stress-related morphological changes in A. woodiana in the vulnerable early juvenile stage.

Unlocking sustainable solutions: controlled Cu2+ dosing enables efficient recovery and reuse of high-purity copper pyrophosphate from electroplating wastewater

The electroplating process of copper pyrophosphate (Cu2P2O7) results in the production of a large volume of wastewater that contains a high concentration of copper (Cu). Currently, conventional lime precipitation creates a substantial amount of secondary pollution, which adds extra economic and environmental burdens. In this study, we suggest a straightforward method for on-site recovery of Cu from Cu2P2O7 electroplating wastewater. By optimizing various parameters, characterizing the resulting product, assessing its electroplating capabilities, and analyzing the speciation during the reaction, we comprehensively investigated the feasibility and mechanism of this technique. The results demonstrated that, under the optimal conditions (Cu/P molar ratio of 0.96, pH of 5.0, and a reaction time of 5.0 min), the concentration of residual Cu remained stable between 22.2 and 27.7 mg/L, even when the initial Cu concentrations varied. The addition of Cu triggered a series of hydrolysis and ionization reactions, primarily leading to the formation of Cu2P2O7·3H2O. The harvested Cu2P2O7·3H2O proved to be suitable for practical electroplating applications, exhibiting comparable performance to commercially available Cu2P2O7·3H2O. This demonstrates the feasibility of recovering high-purity Cu2P2O7·3H2O from copper electroplating wastewater, offering a promising approach for on-site copper reuse and concurrently reducing the demand for natural copper resources. Furthermore, this approach significantly reduces the generation of solid waste, aligning with the principles of sustainable development.

A nanofiber with a p-π conjugated structure designed based on the Jahn-Teller effect for the removal of cupric tartrate from wastewater

Copper organic complexes with strong chemical stability and high solubility in water are difficult to eliminate with traditional adsorbents. In this work, a novel amidoxime nanofiber (AO-Nanofiber) with the p-π conjugated structure was fabricated through homogeneous chemical grafting coupled with electrospinning and applied to capture cupric tartrate (Cu-TA) from aqueous solutions. The adsorption capacity of Cu-TA by AO-Nanofiber was 198.4 mg/g at an equilibrium time of 40 min, and the adsorption performance remains basically unchanged after 10 times adsorption-desorption cycles. The capture mechanism of Cu-TA by AO-Nanofiber was jointly validated by experiments and characterization such as Fourier Transform Infrared Spectrometer (FT-IR), X-ray Photoelectron Spectroscopy (XPS), and Density functional theory (DFT) calculations. These results demonstrated that the lone pair of electrons of the N atom from the amino groups and the O atom from hydroxyl groups in the AO-Nanofiber is partially transferred to the 3d orbital of the Cu(II) ions in Cu-TA, leading to the Jahn-Teller distortion of the Cu-TA and the more stable structure of AO-Nanofiber@Cu-TA was generated.

Micro/nanorobots for remediation of water resources and aquatic life

Nowadays, global water scarcity is becoming a pressing issue, and the discharge of various pollutants leads to the biological pollution of water bodies, which further leads to the poisoning of living organisms. Consequently, traditional water treatment methods are proving inadequate in addressing the growing demands of various industries. As an effective and eco-friendly water treatment method, micro/nanorobots is making significant advancements. Based on researches conducted between 2019 and 2023 in the field of water pollution using micro/nanorobots, this paper comprehensively reviews the development of micro/nanorobots in water pollution control from multiple perspectives, including propulsion methods, decontamination mechanisms, experimental techniques, and water monitoring. Furthermore, this paper highlights current challenges and provides insights into the future development of the industry, providing guidance on biological water pollution control.

Electrocoagulation/flotation process for removing copper from an aqueous environment

The presence of copper in aqueous environments such as drinking water has led to several environmental effects, such as flavor and odor. The increase in Cu levels in ground and surface water has been mainly attributed to anthropogenic and natural sources. Consequently, this applied-analytical study aimed to investigate copper removal from urban drinking water through batch reactor electrocoagulation/flotation (ECF) with aluminum electrodes. The copper removal efficiency was evaluated under various operating conditions of current density (0.8-2.4 mA/cm2), initial concentration (1-100 mg/L), pH (3.5-10.5), and time (10-30 min). Cu was determined using the method outlined in the standard procedures (3500-Cu B at 4571 nm). The results indicated that increasing the current density from 0.8 to 2.4 mA/cm2 and the reaction time from 10 to 30 min improved Cu+2 removal efficiency (from 95 to 100%). In addition, the results demonstrated that Cu+2 reduction is 100% with an initial concentration of 100 mg/L, a pH of 7.5, a reaction time of 30 min, and an anode current density of 2.4 mA/cm2. The Taguchi method results for copper removal efficiency show that reaction time is the most significant variable. Furthermore, Cu removal kinetics models in an ECF reactor are second-order (R2 > 0.92). The Cu removal in the ECF reactor is due to redox and adsorption. Moreover, the operational costs of Cu treatment with Al electrode pairs are estimated to range from 8857 and 9636 Rial/kg of Cu removed. Thus, it can be concluded that the ECF process is very efficient in removing Cu from aqueous environments under optimum conditions.

Computational Insights on the Chemical Reactivity of Functionalized and Crosslinked Polyketones to Cu2+ Ion for Wastewater Treatment

Today, the high concentrations of copper found in water resources result in an urgent problem to solve since human health and aquatic ecosystems have been affected. Functionalized crosslinked polyketone resins (XLPK) have demonstrated high performance for the uptake of heavy metals in water solutions. In addition, its green chemical synthesis makes these resins very attractive as sorbents for metal ions contained in wastewater. XLPK are not soluble in aqueous media and do not require any catalyst, solvent, or harsh conditions to carry out the uptake process. In this paper, a series of functionalized XLPK with pending amino-derivatives namely; butylamine (BA), amino 2-propanol (A2P), 4-(aminomethyl) benzoic acid (HAMC), 6-aminohexanoic acid (PAMBA), and 1,2 diamino propane (DAP) directly attached to the pyrrole backbone of the polymers and crosslinked by di-amine derivatives was investigated using Density Functional Theory (DFT) calculations. Our computational analysis revealed that dipole-dipole interactions played a crucial role in enhancing the adsorption of Cu2+ ions onto XLPKs. The negatively charged ketone moieties and functional groups within XLPKs were identified as key adsorption sites for the selective binding of Cu2+ ions. Additionally, we found that XLPKs exhibited strong electrostatic interactions primarily through the -NH2 and -C=O groups. Evaluation of the adsorption energies in XLPK-Cu(II) complexes showed that the DAP-Cu(II) complex exhibited the highest stability, attributed to strong Cu(II)-N binding facilitated by the amino moiety (-NH2). The remaining XLPKs displayed binding modes involving oxygen atoms (Cu(II)-O) within the ketone moieties in the polymer backbone. Furthermore, the complexation and thermochemical analysis emphasized the role of the coordinator atom (N or O) and the coordinating environment, in which higher entropic effects involved in the adsorption of Cu2+ ions onto XLPKs describes a lower spontaneity of the adsorption process. The adsorption reactions were favored at lower temperatures and higher pressures. These findings provide valuable insights into the reactivity and adsorption mechanisms of functionalized and crosslinked polyketones for Cu2+ uptake, facilitating the design of high-performance polymeric resins for water treatment applications.

Adsorption Characterization of Cu(II) and Cd(II) by a Magnetite-Chitosan Composite: Kinetic, Thermodynamic and Equilibrium Studies

Optimizing the use of magnetite-chitosan composites for heavy metal adsorption has been of great interest due to their environmental friendliness. To gain insights into their potential with green synthesis, this study analyzed one of these composites through X-ray diffraction, Fourier-transform infrared spectroscopy and scanning electron microscopy. Adsorption properties were then explored via static experiments to evaluate the pH dependence, isotherms, kinetics, thermodynamics and regeneration adsorption of Cu(II) and Cd(II). Results disclosed that the optimum pH of adsorption was 5.0, the equilibrium time was about 10 min, and the capacity for Cu(II) and Cd(II) reached 26.28 and 18.67 mg/g, respectively. The adsorption amount of cations increased with temperature from 25 °C to 35 °C and decreased with further increase in temperature from 40 °C to 50 °C, which might be related to the unfolding of chitosan; the adsorption capacity was above 80% of the initial value after two regenerations and about 60% after five regenerations. The composite has a relatively rough outer surface, but its inner surface and porosity are not obvious; it has functional groups of magnetite and chitosan, and chitosan might dominate the adsorption. Consequently, this research proposes the value of maintaining green synthesis research to further optimize the composite system of heavy metal adsorption.