Atomic Force Microscopy: A Powerful Tool to Address Scaffold Design in Tissue Engineering

Exploring the physicochemical traits, antifungal capabilities, and 3D spatial complexity of hydroxyapatite with Ag+Mg2+ substitution in the biocomposite thin films

The silver/magnesium doped hydroxyapatite (AgMgHAp, Ca10-x-yAgxMgy(PO4)6(OH)2, xAg=0.05 and yMg=0.02) nanocomposites coatings were deposited on Si substrate using the dip coating technique. The resulting coatings were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Fourier transform infrared (FTIR-ATR) spectroscopy, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The EDS analysis highlighted the presence of the constitutive elements of the silver/magnesium doped hydroxyapatite (AgMgHAp) nanocomposites coatings. The surface microtexture of the AgMgHAp was assessed by atomic force microscopy (AFM) technique. The AFM data suggested the obtaining of a uniform deposited layer comprised of equally distributed nanoconglomerates. FT-IR studies highlighted the presence of vibrational modes associated with the phosphate and hydroxyl groups. No bands associated with silver or magnesium were observed. The XPS analysis highlighted the presence of the constituent elements of hydroxyapatite (Ca 2p, P 2 s, O 1 s), as well as dopants (Ag 3d, Mg 1 s and Mg 2p). The antifungal evaluation of AgMgHAp coatings was carried out using the Candida albicans ATCC 10231 fungal strain. The results of the antifungal assay revealed that the AgMgHAp coatings exhibited a strong inhibitory antifungal activity. Furthermore, the data highlighted that the AgMgHAp inhibited the development of biofilm on their surface. The results revealed that the antifungal activity of the coating varied based on the duration of incubation. On the other hand, the data also showed that AgMgHAp nanocomposites coatings inhibited the fungal cell adhesion and development from the early stages of the incubation. In addition to morphological analysis, we additionally take advantage of AFM images to investigate and explore the domain of fractal and multifractal analysis applied to the films under evaluation. Our studies indicates that nanocomposite coatings made from AgMgHAp demonstrate strong antifungal properties. Our studies indicates that nanocomposite coatings made from AgMgHAp demonstrate strong antifungal properties. These results suggest the potential of AgMgHAp nanocomposite coatings as a promising solution for developing innovative antifungal devices in biomedical applications.

Electrochemical and DFT insights into 2-amino-4-(4-hydroxy-3-methoxyphenyl)-7-methyl-4H-chromene-3-carbonitrile: an innovative strategy for antibacterial activity and corrosion protection of carbon steel

This study explored the potential of a newly synthesized derivative, 2-amino-4-(4-hydroxy-3-methoxyphenyl)-7-methyl-4H-chromene-3-carbonitrile (AHMCC), as a broad-spectrum antibacterial agent and a corrosion inhibitor for carbon steel (C.STL) in 0.5 M HCl solution. AHMCC demonstrated remarkable antibacterial efficacy against Gram-negative (Escherichia coli, Klebsiella pneumoniae) and Gram-positive (Bacillus subtilis, Staphylococcus aureus) bacteria, as evidenced by agar plate tests and cell viability assays. In the corrosion inhibition studies, AHMCC exhibited mixed-type inhibitor behavior as revealed by potentiodynamic polarization (PDP) measurements. The inhibition efficiency increased with rising AHMCC concentration, confirmed by a significant enhancement in charge transfer resistance (R ct) observed in electrochemical impedance spectroscopy (EIS) analysis. Electrochemical frequency modulation (EFM) data with obtained CF2 and CF3 values further corroborated these findings. Langmuir isotherm modeling suggested AHMCC molecules followed a monolayer adsorption pattern on the C.STL surface. UV-visible spectroscopy indicated the formation of a protective layer through chemical interaction between AHMCC and the metal surface. Atomic force microscopy (AFM) provided visual confirmation of this protective film shielding the C.STL from the corrosive environment. Additionally, theoretical calculations supported the proposed adsorption mechanism of AHMCC molecules onto the C.STL surface.

Immobilization of α-amylase onto functionalized molybdenum diselenide nanoflowers (MoSe2-NFs) as scaffolds: Characterization, kinetics, and potential applications in starch-based industries

The current study presents the application of molybdenum diselenide nanoflowers (MoSe2-NFs) as an innovative substrate for immobilizing α-amylase by glutaraldehyde activation. This approach results in the development of a nanobiocatalyst that exhibits remarkable advantages compared to a standalone enzyme. Several physical methods, such as fluorescence microscopy, FT-IR, SEM, TEM, XRD, AFM, and Raman spectroscopy, were used to confirm that α-amylase was successfully attached to MoSe2-NFs. By employing the Box-Behnken design of the RSM, the parameters were optimized, resulting in an immobilization efficiency of roughly 87.33%. The immobilized variant of α-amylase demonstrated superior thermostability, pH stability, reusability, and storage stability in comparison to the soluble enzyme. The catalytic activity of α-amylase was highest when immobilized on MoSe2-NFs at the same pH and temperature as the soluble enzyme. However, there was an expansion in the range of parameters in which this activity was observed. Furthermore, the immobilized enzyme exhibited a retention of nearly 80% residual activity following 12 successive reuses. The immobilized enzyme exhibited around 82% residual activity after being stored for 120 days. It is possible that the immobilization process changed the Michaelis-Menten constant, which means that the substrate could no longer reach certain active sites on the enzyme because it had become longer. The study's findings suggest that the α-amylase-MoSe2-NFs system could be useful in industry because it can work in a wider range of temperature and pH conditions. Furthermore, the intrinsic non-toxic characteristics of the matrix, along with its ability to be kept for prolonged periods and recycled, render nano biocatalysts very well-suited for the effective synthesis of maltose in the food and pharmaceutical industries.

Vesicle fusion and release in neurons under dynamic mechanical equilibrium

Vesicular fusion plays a pivotal role in cellular processes, involving stages like vesicle trafficking, fusion pore formation, content release, and membrane integration or separation. This dynamic process is regulated by a complex interplay of protein assemblies, osmotic forces, and membrane tension, which together maintain a mechanical equilibrium within the cell. Changes in cellular mechanics or external pressures prompt adjustments in this equilibrium, highlighting the system's adaptability. This review delves into the synergy between intracellular proteins, structural components, and external forces in facilitating vesicular fusion and release. It also explores how cells respond to mechanical stress, maintaining equilibrium and offering insights into vesicle fusion mechanisms and the development of neurological disorders.

Atomic Force Microscopy Applied to the Study of Tauopathies

Atomic force microscopy (AFM) is a scanning probe microscopy technique which has a physical principle, the measurement of interatomic forces between a very thin tip and the surface of a sample, allowing the obtaining of quantitative data at the nanoscale, contributing to the surface study and mechanical characterization. Due to its great versatility, AFM has been used to investigate the structural and nanomechanical properties of several inorganic and biological materials, including neurons affected by tauopathies. Tauopathies are neurodegenerative diseases featured by aggregation of phosphorylated tau protein inside neurons, leading to functional loss and progressive neurotoxicity. In the broad universe of neurodegenerative diseases, tauopathies comprise the most prevalent, with Alzheimer's disease as its main representative. This review highlights the use of AFM as a suitable research technique for the study of cellular damages in tauopathies, even in early stages, allowing elucidation of pathogenic mechanisms of these diseases.

Evaluating the roughness dynamics of kefir biofilms grown on Amazon cupuaçu juice: a monofractal and multifractal approach

We conducted a comprehensive analysis of the surface microtexture of kefir biofilms grown on Theobroma grandiflorum Shum (cupuaçu) juice using atomic force microscopy. Our goal was to investigate the unique monofractal and multifractal spatial patterns of these biofilms to complement the existing limited literature. The biofilms were prepared dispersing four different concentrations of kefir grains in cupuaçu juice. Our morphological analysis showed that the surface of the obtained biofilms is essentially formed by the presence of cupuaçu fibers and microorganisms like lactobacilli and yeast. The topographic height-based parameter analysis reveals that there is a dependence between surface roughness and the concentration of kefir grains used. The strongly anisotropic well-centralized topographical height distribution of the biofilms also exhibited a quasi-symmetrical and platykurtic pattern. The biofilms exhibit comparable levels of spatial complexity, surface percolation and surface homogeneity, which can be attributed to their similar topographic uniformity. This aspect was further supported by the presence of similar multifractality in the biofilms, suggesting that despite their varying topographic roughness, their vertical growth dynamics follow a similar pattern. Our findings demonstrate that the surface roughness of kefir biofilms cultivated on cupuaçu juice is influenced by the concentration of kefir grains in the precursor solution. However, this dependence follows a consistent pattern across different concentrations. Graphical Abstract.

Nanostructured Lipid Carrier-Mediated Transdermal Delivery System of Glibenclamide for Gestational Diabetes: Pharmacokinetic and Pharmacodynamic Evaluation

BACKGROUND

Gestational diabetes mellitus (GDM) poses significant risks during pregnancy for both mother and fetus. Adherence to oral antidiabetic medications, like glibenclamide (GB), can be challenging, necessitating novel drug delivery methods. Nanostructured lipid carriers (NLC) offer a promising approach by efficiently permeating the skin due to their small size and lipid-based composition.

OBJECTIVE

This study aimed to develop and evaluate transdermal patches loaded with glibenclamide NLCs to treat GDM.

METHODS

Glibenclamide NLCs were prepared using hot homogenization with ultrasonication and melt dispersion method. A central composite design was utilized to optimize the formulations. Transdermal patches containing optimized NLCs were developed using HPMC K 100 and Eudragit L polymers. The patches were evaluated for various parameters, and their pharmacokinetic and pharmacodynamic studies were carried out to assess their safety and efficacy.

RESULTS

Optimized NLCs efficiently permeated rat skin. Cell viability studies indicated the nontoxicity of the formulations. NLC-loaded transdermal patches (F2 and F7) showed drug release of 1098 μg/cm2 and 1001.83 μg/cm2 in 24 h, with a 2.5-fold higher flux and permeation coefficient than the GB patch. Pharmacokinetic analysis revealed Tmax of 8 and 10 h and Cmax of 7127 ng/ml and 7960 ng/ml for F2 and F7, respectively, ensuring sustained drug action. AUC0-α was 625681 ng/ml·h and 363625 ng/ml·h for F2 and F7, respectively, indicating improved bioavailability.

CONCLUSION

Transdermal patches incorporating NLCs hold promise for enhancing glibenclamide's therapeutic efficacy in GDM treatment. Improved skin permeation, sustained drug release, and enhanced bioavailability make NLC-based transdermal patches a potential alternative with better patient compliance.

Nanomechanical Mapping of Three Dimensionally Printed Poly-ε-Caprolactone Single Microfibers at the Cell Scale for Bone Tissue Engineering Applications

Poly-ε-caprolactone (PCL) has been widely used in additive manufacturing for the construction of scaffolds for bone tissue engineering. However, its use is limited by its lack of bioactivity and inability to induce cell adhesion, hence limiting bone tissue regeneration. Biomimicry is strongly influenced by the dynamics of cell-substrate interaction. Thus, characterizing scaffolds at the cell scale could help to better understand the relationship between surface mechanics and biological response. We conducted atomic force microscopy-based nanoindentation on 3D-printed PCL fibers of ~300 µm thickness and mapped the near-surface Young's modulus at loading forces below 50 nN. In this non-disruptive regime, force mapping did not show clear patterns in the spatial distribution of moduli or a relationship with the topographic asperities within a given region. Remarkably, we found that the average modulus increased linearly with the logarithm of the strain rate. Finally, a dependence of the moduli on the history of nanoindentation was demonstrated on locations of repeated nanoindentations, likely due to creep phenomena capable of hindering viscoelasticity. Our findings can contribute to the rational design of scaffolds for bone regeneration that are capable of inducing cell adhesion and proliferation. The methodologies described are potentially applicable to various tissue-engineered biopolymers.

Preparation and Microscopic Mechanical Characterization of L-Methionine-Based Polyphosphazene Fibrous Mats for Vascular Tissue Engineering

This study investigates the mechanical properties, degradation behavior, and biocompatibility of poly[(α-amino acid ester) phosphazene] electrospun fibers based on the ethyl ester of L-methionine (PαAPz-M), a material with potential applications in tissue engineering. We utilized atomic force microscopy (AFM) to evaluate the fiber mechanical characteristics and calculate its Young's modulus, revealing it to closely mimic the stiffness of a natural extracellular matrix (ECM). We also studied the degradation behavior of PαAPz-M scaffolds over 21 days, showing that they maintain the highly porous structure required for tissue engineering. Further evaluation of mesenchymal multipotent 10T1/2 cell and mesenchymal stem cell (MSC) behavior on the scaffolds demonstrated significant cell viability, proliferation, and successful MSC differentiation into smooth muscle cells. Expression of collagen and elastin by MSCs on the fiber mats highlighted potential ECM formation during scaffold degradation, confirming PαAPz-M as a promising material for vascular tissue engineering.

Strategic outline of interventions targeting extracellular matrix for promoting healthy longevity

The extracellular matrix (ECM), composed of interlinked proteins outside of cells, is an important component of the human body that helps maintain tissue architecture and cellular homeostasis. As people age, the ECM undergoes changes that can lead to age-related morbidity and mortality. Despite its importance, ECM aging remains understudied in the field of geroscience. In this review, we discuss the core concepts of ECM integrity, outline the age-related challenges and subsequent pathologies and diseases, summarize diagnostic methods detecting a faulty ECM, and provide strategies targeting ECM homeostasis. To conceptualize this, we built a technology research tree to hierarchically visualize possible research sequences for studying ECM aging. This strategic framework will hopefully facilitate the development of future research on interventions to restore ECM integrity, which could potentially lead to the development of new drugs or therapeutic interventions promoting health during aging.

Characterization of Biocompatibility of Functional Bioinks for 3D Bioprinting

Three-dimensional (3D) bioprinting with suitable bioinks has become a critical tool for fabricating 3D biomimetic complex structures mimicking physiological functions. While enormous efforts have been devoted to developing functional bioinks for 3D bioprinting, widely accepted bioinks have not yet been developed because they have to fulfill stringent requirements such as biocompatibility and printability simultaneously. To further advance our knowledge of the biocompatibility of bioinks, this review presents the evolving concept of the biocompatibility of bioinks and standardization efforts for biocompatibility characterization. This work also briefly reviews recent methodological advances in image analyses to characterize the biocompatibility of bioinks with regard to cell viability and cell-material interactions within 3D constructs. Finally, this review highlights a number of updated contemporary characterization technologies and future perspectives to further advance our understanding of the biocompatibility of functional bioinks for successful 3D bioprinting.

Controlled release of silica-coated insulin-loaded chitosan nanoparticles as a promising oral administration system

BACKGROUND

Oral insulin administration has recently become one of the most exciting research subjects. Different approaches have been carried out to get an effective oral insulin delivery system using nanotechnology. The development of a delivery system that overcomes the difficulties of oral insulin administration, achieving high stability and minimal side effects, is still an urgent need. Therefore, this study is considered one of the efforts to design a new prospective drug delivery nano-composite (silica-coated chitosan-dextran sulfate nanoparticles).

METHODS

Chitosan-dextran sulfate nanoparticles (CS-DS NPs) were prepared via a complex coacervation method and then coated with silica. Uncoated and silica-coated CS-DS NPs were physically characterized via different techniques. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analysis, and atomic force microscopy (AFM) have been used to investigate the chemical elements, size, morphology, and surface properties of the prepared formulations. Differential scanning calorimetry (DSC) to assess the thermal properties of formed nano-formulations. Fourier transform infrared (FT-IR) spectroscopy investigated the silica coat and chitosan interaction. The encapsulation efficiency was evaluated using high-performance liquid chromatography (HPLC) analysis. The insulin release profile of nano-formulations was performed with and without silica coat at two different pHs (5.5,7), nearly simulating the environment of the gastrointestinal tract (GIT).

RESULTS

The silica-coated CS-DS NPs revealed interesting physicochemical properties exemplified by suitable core particle size obtained by TEM images (145.31 ± 33.15 nm), hydrodynamic diameter (210 ± 21 nm), high stability indicated by their zeta potential value (-32 ± 3.2 mV), and adequate surface roughness assessed by AFM. The encapsulation efficiency of insulin-loaded chitosan nanoparticles (ICN) was (66.5%) higher than that of insulin-chitosan complex nanoparticles (ICCN). The silica-coated ICN demonstrated a controlled insulin release profile at pHs (5.5 and 7) compared with uncoated ICN.

CONCLUSION

The silica-coated ICN can be an efficient candidate as a desired oral delivery system, overcoming the common obstacles of peptides and proteins delivery and achieving high stability and controlled release for further applications.

Bioinspired Synthesis of Magnetic Nanoparticles Based on Iron Oxides Using Orange Waste and Their Application as Photo-Activated Antibacterial Agents

Magnetic nanoparticles based on iron oxides (MNPs-Fe) have been proposed as photothermal agents (PTAs) within antibacterial photothermal therapy (PTT), aiming to counteract the vast health problem of multidrug-resistant bacterial infections. We present a quick and easy green synthesis (GS) to prepare MNPs-Fe harnessing waste. Orange peel extract (organic compounds) was used as a reducing, capping, and stabilizing agent in the GS, which employed microwave (MW) irradiation to reduce the synthesis time. The produced weight, physical-chemical features and magnetic features of the MNPs-Fe were studied. Moreover, their cytotoxicity was assessed in animal cell line ATCC RAW 264.7, as well as their antibacterial activity against Staphylococcus aureus and Escherichia coli. We found that the 50GS-MNPs-Fe sample (prepared by GS, with 50% v/v of NH₄OH and 50% v/v of orange peel extract) had an excellent mass yield. Its particle size was ~50 nm with the presence of an organic coating (terpenes or aldehydes). We believe that this coating improved the cell viability in extended periods (8 days) of cell culture with concentrations lower than 250 µg·mL^-1, with respect to the MNPs-Fe obtained by CO and single MW, but it did not influence the antibacterial effect. The bacteria inhibition was attributed to the plasmonic of 50GS-MNPs-Fe (photothermal effect) by irradiation with red light (630 nm, 65.5 mW·cm^-2, 30 min). We highlight the superparamagnetism of the 50GS-MNPs-Fe over 60 K in a broader temperature range than the MNPs-Fe obtained by CO (160.09 K) and MW (211.1 K). Therefore, 50GS-MNPs-Fe could be excellent candidates as broad-spectrum PTAs in antibacterial PTT. Furthermore, they might be employed in magnetic hyperthermia, magnetic resonance imaging, oncological treatments, and so on.

Circulating Tumor Cells in Cancer Diagnostics and Prognostics by Single-Molecule and Single-Cell Characterization

Circulating tumor cells (CTCs) represent an interesting source of biomarkers for diagnosis, prognosis, and the prediction of cancer recurrence, yet while they are extensively studied in oncobiology research, their diagnostic utility has not yet been demonstrated and validated. Their scarcity in human biological fluids impedes the identification of dangerous CTC subpopulations that may promote metastatic dissemination. In this Perspective, we discuss promising techniques that could be used for the identification of these metastatic cells. We first describe methods for isolating patient-derived CTCs and then the use of 3D biomimetic matrixes in their amplification and analysis, followed by methods for further CTC analyses at the single-cell and single-molecule levels. Finally, we discuss how the elucidation of mechanical and morphological properties using techniques such as atomic force microscopy and molecular biomarker identification using nanopore-based detection could be combined in the future to provide patients and their healthcare providers with a more accurate diagnosis.

2-DOF Fractional Order PID Control Based on BP Neural Network for Atomic Force Microscope

To enhance trajectory tracking performance of atomic force microscope system, a two-degree of freedom fractional order PID (2-DOF FOPID) control approach based on back propagation (BP) neural network is proposed in this paper. At first, principle and structure of the proposed control approach is presented. Then, 2-DOF FOPID controller is designed, including in feedforward and feedback controller, fractional calculus and approximation of fractional operator. Meanwhile, the parameters of controller are analyzed. Based on them, a BP neural network is built to adjust the parameters in this control structure according to the error between the reference trajectory and the actual output. Finally, the proposed control approach is conducted in atomic force microscope tracking control experiment, experimental results verify the effectiveness and improvement of the proposed control approach.

Objective speckle pattern-based surface roughness measurement using matrix factorization

A method for the measurement of profile parameters of both isotropic and anisotropic surfaces is presented using the objective laser speckle imaging technique. The surface parameters are characterized in terms of a singular value decomposition method-based metric derived from the initial key contributing singular values of the speckle pattern. A simulation study is performed with random Gaussian anisotropic surfaces generated as a function of the correlation lengths in both x and y directions. In the experimental demonstration, the proposed method is verified with metallic samples having distinct surface roughness processed through widely used machining operations viz., vertical milling, and grinding. A brief discussion about the extent to which the minimum number of singular values that are sufficient to evaluate the profile parameters in the context of experimental results is provided. The method supports the measurement of profile parameters of higher magnitude in the realm of non-contact topographic measurement techniques. The experimental results substantiate the practical applicability of the proposed method.

Water Stress-Driven Changes in Bacterial Cell Surface Properties

Increased drought intensity and frequency exposes soil bacteria to prolonged water stress. While numerous studies reported on behavioral and physiological mechanisms of bacterial adaptation to water stress, changes in bacterial cell surface properties during adaptation are not well researched. We studied adaptive changes in cell surface hydrophobicity (CSH) after exposure to osmotic (NaCl) and matric stress (polyethylene glycol 8000 [PEG 8000]) for six typical soil bacteria (Bacillus subtilis, Arthrobacter chlorophenolicus, Pseudomonas fluorescens, Novosphingobium aromaticivorans, Rhodococcus erythropolis, and Mycobacterium pallens) covering a wide range of cell surface properties. Additional physicochemical parameters (surface chemical composition, surface charge, cell size and stiffness) of B. subtilis and P. fluorescens were analyzed to understand their possible contribution to CSH development. Changes in CSH caused by osmotic and matric stress depend on strain and stress type. CSH of B. subtilis and P. fluorescens increased with stress intensity, R. erythropolis and M. pallens exhibited a generally high but constant contact angle, while the response of A. chlorophenolicus and N. aromaticivorans depended on growth conditions and stress type. Osmotically driven changes in CSH of B. subtilis and P. fluorescens are accompanied by increasing surface N/C ratio, suggesting an increase in protein concentration within the cell wall. Cell envelope proteins thus presumably control bacterial CSH in two ways: (i) by increases in the relative density of surface proteins due to efflux of cytoplasmic water and subsequent cell shrinkage, and (ii) by destabilization of cell wall proteins, resulting in conformational changes which render the surface more hydrophobic. IMPORTANCE Changes in precipitation frequency, intensity, and temporal distribution are projected to result in increased frequency and intensity of droughts and heavy rainfall events. Prolonged droughts can promote the development of soil water repellency (SWR); this impacts the infiltration and distribution of water in the soil profile, exposing soil microorganisms to water stress. Exposure to water stress has recently been reported to result in increased cell surface hydrophobicity. However, the mechanism of this development is poorly understood. This study investigates the changes in the physicochemical properties of bacterial cell surfaces under water stress as a possible mechanism of increased surface hydrophobicity. Our results improve understanding of the microbial response to water stress in terms of surface properties, the variations in stress response depending on cell wall composition, and its contribution to the development of SWR.

Color changes and shear bond strength to simulated caries lesions treated with a novel solution of 20% silver nanoclusters in polymethacrylic acid

The aims of the study were: (1) To compare the staining effect on demineralized dentin simulating caries between silver nanoclusters (AgNCls) synthesized using polymethacrylic acid (PMAA) and silver diammine fluoride (SDF), and (2) to measure the shear bond strength (SBS) of a glass ionomer cement (GIC) to simulated caries lesions with and without the application of AgNCls/PMAA or SDF. Dentine blocks 4 mm thick from twenty-four non-carious third molars were sectioned and coated with nail varnish (Revlon, New York, USA). Simulated caries lesions on occlusal dentin surfaces were created (66 h in 0.05 M acetate buffer 2.2 mM calcium/phosphate pH 5.0). Specimens were divided into groups and treated with (n = 8): (A) 20% AgNCls/PMAA; (B) SDF 38% (Fagamin, Tedequim, Córdoba, Argentina); or (C) without treatment. AgNCls/PMAA or SDF were applied on the exposed surfaces with a microbrush for 10 s. Samples were incubated for 24 h at 37 °C at 100% relative humidity. Surface color was measured according to the CIE-L*a*b* system before and after demineralization (R0 and R1), 24 h and one week after treatment (R2 and R3), using a spectrophotometer (CM-600D Konica Minolta Sesing Inc., Japan). Groups A and B received an extra application of AgNCls/PMAA or SDF before a conventional GIC (Fuji IX-Gold Label, GC Corp, Tokyo, Japan) was bonded using a mold, 4 mm diameter × 3 mm high. For SBS, a Universal Testing Machine (Digimess RS-8000-5, China)—crosshead speed of 1 mm/min—was used. Statistical analysis was performed using ANOVA, Student-t and Scheffe-test at a significance of p < 0.05. Group A presented a stable color p = 0.24 between R1-R2 and R1-R3 in contrast to significant color changes in Group B (p = 0.02). SBS was higher (p < 0.01) in Group A (10.4 ± 2.7 MPa) compared to Groups B (3.3 ± 1.3 MPa) and C (4.0 ± 0.4 MPa), where no differences between the latter groups were observed (p = 0.77). Results of this preliminary study demonstrated that 20% AgNCls/PMAA did not stain simulated carious dentin and improved SBS of the GIC. The relevance of this study relies on the development of a therapeutic system to potentially arrest caries lesions without staining.

Surface aspects and multifractal features of 3D spatial patterns of low-cost Amazon açaí-loaded kefir microbial films

In this study, açaí-loaded kefir microbial films obtained in solutions containing demerara sugar, a low-cost and relatively organic sugar, were prepared. Environmental scanning electron microscopy (ESEM), atomic force microscopy (AFM), stereometric and multifractal analyses were applied to study the influence of the concentration of açaí over the surface morphology as well as its multifractal nature. The ESEM and AFM images showed that low concentrations of acai berry form surface covered by bacteria, while higher concentrations promote yeast growth. The autocorrelation function suggested that the degree of surface anisotropy changes as the concentration of açaí increases, while the Minkowski Functionals confirmed that the sample with the highest content has a different morphology than the samples containing 10-40 ml. The multifractal analysis revealed that the surfaces have a strong multifractal behavior, where the multifractal singularity strength was higher in the sample containing the highest concentration of açaí. The sample with the highest concentration was then mapped to have a greater vertical growth of its spatial patterns. These results prove that image analysis using mathematical tools can be very useful for the characterization of biological-based systems for application in the biomedicine field. We characterized the micromorphology of the 3D surface of the kefir biofilms associated with Acai extract. The 3D surface analysis of the samples was performed using by environmental scanning electron microscope and atomic force microscopy. We determined the multifractal and Minkowski Functionals of the analyzed samples.

Detection of HOCl-driven degradation of the pericardium scaffolds by label-free multiphoton fluorescence lifetime imaging

Artificial biomaterials can significantly increase the rate of tissue regeneration. However, implantation of scaffolds leads not only to accelerated tissue healing but also to an immune response of the organism, which results in the degradation of the biomaterial. The synergy of the immune response and scaffold degradation processes largely determines the efficiency of tissue regeneration. Still, methods suitable for fast, accurate and non-invasive characterization of the degradation degree of biomaterial are highly demandable. Here we show the possibility of monitoring the degradation of decellularized bovine pericardium scaffolds under conditions mimicking the immune response and oxidation processes using multiphoton tomography combined with fluorescence lifetime imaging (MPT-FLIM). We found that the fluorescence lifetimes of genipin-induced cross-links in collagen and oxidation products of collagen are prominent markers of oxidative degradation of scaffolds. This was verified in model experiments, where the oxidation was induced with hypochlorous acid or by exposure to activated neutrophils. The fluorescence decay parameters also correlated with the changes of micromechanical properties of the scaffolds as assessed using atomic force microscopy (AFM). Our results suggest that FLIM can be used for quantitative assessments of the properties and degradation of the scaffolds essential for the wound healing processes in vivo.

Electrochemical biosensor for nucleic acid amplification-free and sensitive detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) RNA via CRISPR/Cas13a trans-cleavage reaction

The outbreak of the COVID-19 pandemic has led to millions of fatalities worldwide. For preventing epidemic transmission, rapid and accurate virus detection methods to early identify infected people are urgently needed in the current situation. Therefore, an electrochemical biosensor based on the trans-cleavage activity of CRISPR/Cas13a was developed in this study for rapid, sensitive, and nucleic-acid-amplification-free detection of the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Herein, a redox probe conjugated with ssRNA is immobilized on the electrode surface modified with a nanocomposite (NC) and gold nanoflower (AuNF) for enhancing the sensing performance. The SARS-CoV-2 RNA is captured by the Cas13a-crRNA complex, which triggers the RNase function of Cas13a. The enzymatically activated Cas13a-crRNA complex is subsequently introduced to the reRNA-conjugated electrochemical sensor, and consequently cleaves the reRNA. A change in current occurs due to the release of the redox molecule labeled on the reRNA, which is trans-cleaved from the Cas13a-crRNA complex. The biosensor can detect as low as 4.4 × 10-2 fg/mL and 8.1 × 10-2 fg/mL of ORF and S genes, respectively, over a wide dynamic range (1.0 × 10-1 to 1.0 × 105 fg/mL). Moreover, the biosensor was evaluated by measuring SARS-CoV-2 RNA spiked in artificial saliva. The recovery of the developed sensor was found to be in an agreeable range of 96.54-101.21%. The designed biosensor lays the groundwork for pre-amplification-free detection of ultra-low concentrations of SARS-CoV-2 RNA and on-site and rapid diagnostic testing for COVID-19.

Biomaterials via peptide assembly: Design, characterization, and application in tissue engineering

A core challenge in biomaterials, with both fundamental significance and technological relevance, concerns the rational design of bioactive microenvironments. Designed properly, peptides can undergo supramolecular assembly into dynamic, physical hydrogels that mimic the mechanical, topological, and biochemical features of native tissue microenvironments. The relatively facile, inexpensive, and automatable preparation of peptides, coupled with low batch-to-batch variability, motivates the expanded use of assembling peptide hydrogels for biomedical applications. Integral to realizing dynamic peptide assemblies as functional biomaterials for tissue engineering is an understanding of the molecular and macroscopic features that govern assembly, morphology, and biological interactions. In this review, we first discuss the design of assembling peptides, including primary structure (sequence), secondary structure (e.g., α-helix and β-sheets), and molecular interactions that facilitate assembly into multiscale materials with desired properties. Next, we describe characterization tools for elucidating molecular structure and interactions, morphology, bulk properties, and biological functionality. Understanding of these characterization methods enables researchers to access a variety of approaches in this ever-expanding field. Finally, we discuss the biological properties and applications of peptide-based biomaterials for engineering several important tissues. By connecting molecular features and mechanisms of assembling peptides to the material and biological properties, we aim to guide the design and characterization of peptide-based biomaterials for tissue engineering and regenerative medicine. STATEMENT OF SIGNIFICANCE: Engineering peptide-based biomaterials that mimic the topological and mechanical properties of natural extracellular matrices provide excellent opportunities to direct cell behavior for regenerative medicine and tissue engineering. Here we review the molecular-scale features of assembling peptides that result in biomaterials that exhibit a variety of relevant extracellular matrix-mimetic properties and promote beneficial cell-biomaterial interactions. Aiming to inspire and guide researchers approaching this challenge from both the peptide biomaterial design and tissue engineering perspectives, we also present characterization tools for understanding the connection between peptide structure and properties and highlight the use of peptide-based biomaterials in neural, orthopedic, cardiac, muscular, and immune engineering applications.

Scanning Probe Lithography: State-of-the-Art and Future Perspectives

High-throughput and high-accuracy nanofabrication methods are required for the ever-increasing demand for nanoelectronics, high-density data storage devices, nanophotonics, quantum computing, molecular circuitry, and scaffolds in bioengineering used for cell proliferation applications. The scanning probe lithography (SPL) nanofabrication technique is a critical nanofabrication method with great potential to evolve into a disruptive atomic-scale fabrication technology to meet these demands. Through this timely review, we aspire to provide an overview of the SPL fabrication mechanism and the state-the-art research in this area, and detail the applications and characteristics of this technique, including the effects of thermal aspects and chemical aspects, and the influence of electric and magnetic fields in governing the mechanics of the functionalized tip interacting with the substrate during SPL. Alongside this, the review also sheds light on comparing various fabrication capabilities, throughput, and attainable resolution. Finally, the paper alludes to the fact that a majority of the reported literature suggests that SPL has yet to achieve its full commercial potential and is currently largely a laboratory-based nanofabrication technique used for prototyping of nanostructures and nanodevices.

AFM Stiffness Mapping in Human Aortic Smooth Muscle Cells

Aortic Smooth Muscle Cells (SMCs) play a vital role in maintaining mechanical homeostasis in the aorta. We recently found that SMCs of aneurysmal aortas apply larger traction forces than SMCs of healthy aortas. This result was explained by the significant increase of hypertrophic SMCs abundance in aneurysms. In the present study, we investigate whether the cytoskeleton stiffness of SMCs may also be altered in aneurysmal aortas. For that, we use Atomic Force Microscopy (AFM) nanoindentation with a specific mode that allows subcellular-resolution mapping of the local stiffness across a specified region of interest of the cell. Aortic SMCs from a commercial human lineage (AoSMCs, Lonza) and primary aneurysmal SMCs (AnevSMCs) are cultured in conditions promoting the development of their contractile apparatus, and seeded on hydrogels with stiffness properties of 12kPa and 25kPa. Results show that all SMC exhibit globally a lognormal stiffness distribution, with medians in the range 10-30 kPa. The mean of stiffness distributions is slightly higher in aneurysmal SMCs than in healthy cells (16 kPa versus 12 kPa) but the differences are not statistically significant due to the large dispersion of AFM nanoindentation stiffness. We conclude that the possible alterations previously found in aneurysmal SMCs do not affect significantly the AFM nanoindentation stiffness of their cytoskeleton.

Atomic force microscopy analysis of the surface alterations of enamel, dentin, composite and ceramic materials exposed to low oral pH in GERD

Dental erosion is a significant topic in medical literature, both for gastroenterology and dental medicine. Dental structure loss has a psychosocial and functional significance. The pathogenesis of dental erosion in patients diagnosed with gastroesophageal reflux disease (GERD) characterized by the presence of an acidic oral environment after reflux episodes, is not well understood. The present study was designed to observe the effect of low oral pH in time on natural surfaces including enamel and dentine, but also on materials used in treating these dental destructions such as composites and ceramics. The acidic oral environment was estimated in relation to salivary pH. In the dental laboratory, 5-mm2 and 1-mm composite pieces of thick enamel, dentine, Emax Ceramic and Nexco Ivoclar were cut in order to be analyzed using atomic force microscopy (AFM) and to observe the surface alterations. Gastric acid was collected and mixed with saliva until a pH value of 6.0 was obtained, in which the pieces were immersed for 24, 120, 240 h. Roughness of each surface was calculated at a microstructure and nanostructure level. The results showed significant alterations in enamel and dentine exposed to a lower pH level beginning even at a short immersion time, in comparison with composites and ceramics which had no alterations. In conclusion, multidisciplinary attention should be given to detect and manage acidity of the oral cavity caused by GERD, in order to prevent dental erosion.

Mesoporous Silica Particles as Drug Delivery Systems-The State of the Art in Loading Methods and the Recent Progress in Analytical Techniques for Monitoring These Processes

Conventional administration of drugs is limited by poor water solubility, low permeability, and mediocre targeting. Safe and effective delivery of drugs and therapeutic agents remains a challenge, especially for complex therapies, such as cancer treatment, pain management, heart failure medication, among several others. Thus, delivery systems designed to improve the pharmacokinetics of loaded molecules, and allowing controlled release and target specific delivery, have received considerable attention in recent years. The last two decades have seen a growing interest among scientists and the pharmaceutical industry in mesoporous silica nanoparticles (MSNs) as drug delivery systems (DDS). This interest is due to the unique physicochemical properties, including high loading capacity, excellent biocompatibility, and easy functionalization. In this review, we discuss the current state of the art related to the preparation of drug-loaded MSNs and their analysis, focusing on the newest advancements, and highlighting the advantages and disadvantages of different methods. Finally, we provide a concise outlook for the remaining challenges in the field.

Recent advances in techniques for fabrication and characterization of nanogap biosensors: A review

Nanogap biosensors have fascinated researchers due to their excellent electrical properties. Nanogap biosensors comprise three arrays of electrodes that form nanometer-size gaps. The sensing gaps have become the major building blocks of several sensing applications, including bio- and chemosensors. One of the advantages of nanogap biosensors is that they can be fabricated in nanoscale size for various downstream applications. Several studies have been conducted on nanogap biosensors, and nanogap biosensors exhibit potential material properties. The possibilities of combining these unique properties with a nanoscale-gapped device and electrical detection systems allow excellent and potential prospects in biomolecular detection. However, their fabrication is challenging as the gap is becoming smaller. It includes high-cost, low-yield, and surface phenomena to move a step closer to the routine fabrications. This review summarizes different feasible techniques in the fabrication of nanogap electrodes, such as preparation by self-assembly with both conventional and nonconventional approaches. This review also presents a comprehensive analysis of the fabrication, potential applications, history, and the current status of nanogap biosensors with a special focus on nanogap-mediated bio- and chemical sonsors.

Two-dimensional (2D) dynamic vibration optical coherence elastography (DV-OCE) for evaluating mechanical properties: a potential application in tissue engineering

Mechanical properties in tissues are an important indicator because they are associated with disease states. One of the well-known excitation sources in optical coherence elastography (OCE) to determine mechanical properties is acoustic radiation force (ARF); however, a complicated focusing alignment cannot be avoided. Another excitation source is a piezoelectric (PZT) stack to obtain strain images via compression, which can affect the intrinsic mechanical properties of tissues in tissue engineering. In this study, we report a new technique called two-dimensional (2D) dynamic vibration OCE (DV-OCE) to evaluate 2D wave velocities without tedious focusing alignment procedures and is a non-contact method with respect to the samples. The three-dimensional (3D) Fourier transform was utilized to transfer the traveling waves (x, y, t) into 3D k-space (k_x, k_y, f). A spatial 2D wavenumber filter and multi-angle directional filter were employed to decompose the waves with omni-directional components into four individual traveling directions. The 2D local wave velocity algorithm was used to calculate a 2D wave velocity map. Six materials, two homogeneous phantoms with 10 mm thickness, two homogeneous phantoms with 2 mm thickness, one heterogeneous phantom with 2 mm diameter inclusion and an ex vivo porcine kidney, were examined in this study. In addition, the ARF-OCE was used to evaluate wave velocities for comparison. Numerical simulations were performed to validate the proposed 2D dynamic vibration OCE technique. We demonstrate that the experimental results were in a good agreement with the results from ARF-OCE (transient OCE) and numerical simulations. Our proposed 2D dynamic vibration OCE could potentially pave the way for mechanical evaluation in tissue engineering and for laboratory translation with easy-to-setup and contactless advantages.

An overview of nanoemulsion characterization via atomic force microscopy

Nanoemulsion-based systems are widely applied in food industries for protecting active ingredients against oxidation and degradation and controlling the release rate of active core ingredients under particular conditions. Visualizing the interface morphology and measuring the interfacial interaction forces of nanoemulsion droplets are essential to tailor and design intelligent nanoemulsion-based systems. Atomic force microscopy (AFM) is being established as an important technique for interface characterization, due to its unique advantages over traditional imaging and surface force-determining approaches. However, there is a gap in knowledge about the applicability of AFM in characterizing the droplet interface properties of nanoemulsions. This review aims to describe the fundamentals of the AFM technique and nanoemulsions, mainly focusing on the recent use of AFM to investigate nanoemulsion properties. In addition, by reviewing interfacial studies on emulsions in general, perspectives for the further development of AFM to study nanoemulsions are also discussed.

Physicochemical Characterization of Bioactive Compounds in Nanocarriers

The encapsulation of bioactive compounds is an emerging technique for finding new medicines since it provides protection against ambient degradation factors before reaching the target site. Nanotechnology provides new methods for encapsulating bioactive compounds and for drug carrier development. Nanocarriers satisfactorily impact the absorption, distribution, metabolism, and excretion rate when compared to conventional carriers. The nanocarrier material needs to be compatible and bind to the drug and be bio-resorbable. In this context, the physicochemical characterization of encapsulated bioactive compounds is fundamental to guarantee the quality, reproducibility, and safety of the final pharmaceutical product. In this review, we present the physicochemical techniques most used today by researchers to characterize bioactive compounds in nanocarriers and the main information provided by each technique, such as morphology, size, degree of crystallinity, long-term stability, the efficacy of drug encapsulation, and the amount released as a function of time.

Mechanical properties of anterior lens capsule assessed with AFM and nanoindenter in relation to human aging, pseudoexfoliation syndrome, and trypan blue staining

The purpose of this study is the mechanical characterization of the mid-to- old-age human anterior lens capsules (ALCs) obtained by capsulorhexis using Atomic Force Microscopy (AFM) and a nanoindenter at different spatial scales. The dependencies on the human age, presence or absence of pseudoexfoliation syndrome (PEX), and application of trypan blue staining during the surgery were analyzed. The measurements on both the anterior (AS) and epithelial (ES) sides of the ALC were conducted and the effect of cells present on the epithelial side was carefully accounted for. The ES of the ALC had a homogenous distribution of the Young's modulus over the surface as shown by the macroscale mapping with the nanoindenter and local AFM indentations, while the AS was more heterogeneous. Age-related changes were assessed in groups ranging from the mid-age (from 48 years) to old-age (up to 93 years). We found that the ES was always stiffer than the AS, and this difference decreased with age due to a gradual decrease in the Young's modulus of the ES and an increase in the modulus of the AS. No significant changes were found in the mechanical properties of ALCs of PEX patients versus the PEX-free group, as well as in the properties of the ALC with and without trypan blue staining.

Multiphoton Microscopy for the Characterization of Cellular Behavior on Naturally Derived Polysaccharide Tissue Constructs With Irregular Surfaces for the Development of Platform Biomaterials

Over the past decade, the use of polymers as platform materials for biomedical applications including tissue engineering has been of rising interest. Recently, the use of naturally derived polysaccharides as 3-D scaffolds for tissue regeneration has shown promising material characteristics; however, due to complexities in composition, morphology, and optical properties, adequate spatial and temporal characterization of cellular behavior in these materials is lacking. Multiphoton microscopy has emerged as a viable tool for performing such quantification by permitting greater imaging depth while simultaneously minimizing un-favorable scattering and producing high-resolution optical cross sections for non-invasive analysis. Here we describe a method using endogenous contrast of cellulose nanofibers (CNF) using Second Harmonic Generation (SHG), combined with 2-photon fluorescence of Cell Tracker Orange for spatial and longitudinal imaging of cellular proliferation. Cell Tracker Orange is an ideal fluorophore to avoid the broad CNF autofluorescence allowing for segmentation of cells using a semi-automatic routine. Individual cells were identified using centroid locations for 3D cell proliferation. Overall, the methods presented are viable for investigation of cellular interactions with polysaccharide candidate biomaterials.

Review: Cantilever-Based Sensors for High Speed Atomic Force Microscopy

This review critically summarizes the recent advances of the microcantilever-based force sensors for atomic force microscope (AFM) applications. They are one the most common mechanical spring-mass systems and are extremely sensitive to changes in the resonant frequency, thus finding numerous applications especially for molecular sensing. Specifically, we comment on the latest progress in research on the deflection detection systems, fabrication, coating and functionalization of the microcantilevers and their application as bio- and chemical sensors. A trend on the recent breakthroughs on the study of biological samples using high-speed atomic force microscope is also reported in this review.

Recent Applications of Advanced Atomic Force Microscopy in Polymer Science: A Review

Atomic force microscopy (AFM) has been extensively used for the nanoscale characterization of polymeric materials. The coupling of AFM with infrared spectroscope (AFM-IR) provides another advantage to the chemical analyses and thus helps to shed light upon the study of polymers. This paper reviews some recent progress in the application of AFM and AFM-IR in polymer science. We describe the principle of AFM-IR and the recent improvements to enhance its resolution. We also discuss the latest progress in the use of AFM-IR as a super-resolution correlated scanned-probe infrared spectroscopy for the chemical characterization of polymer materials dealing with polymer composites, polymer blends, multilayers, and biopolymers. To highlight the advantages of AFM-IR, we report several results in studying the crystallization of both miscible and immiscible blends as well as polymer aging. Finally, we demonstrate how this novel technique can be used to determine phase separation, spherulitic structure, and crystallization mechanisms at nanoscales, which has never been achieved before. The review also discusses future trends in the use of AFM-IR in polymer materials, especially in polymer thin film investigation.

Integrating Microstructured Electrospun Scaffolds in an Open Microfluidic System for in Vitro Studies of Human Patient-Derived Primary Cells

Recent studies have suggested that microenvironmental stimuli play a significant role in regulating cellular proliferation and migration, as well as in modulating self-renewal and differentiation processes of mammary cells with stem cell (SCs) properties. Recent advances in micro/nanotechnology and biomaterial synthesis/engineering currently enable the fabrication of innovative tissue culture platforms suitable for maintenance and differentiation of SCs in vitro. Here, we report the design and fabrication of an open microfluidic device (OMD) integrating removable poly(ε-caprolactone) (PCL) based electrospun scaffolds, and we demonstrate that the OMD allows investigation of the behavior of human cells during in vitro culture in real time. Electrospun scaffolds with modified surface topography and chemistry can influence attachment, proliferation, and differentiation of mammary SCs and epigenetic mechanisms that maintain luminal cell identity as a function of specific morphological or biochemical cues imparted by tailor-made fiber post-treatments. Meanwhile, the OMD architecture allows control of cell seeding and culture conditions to collect more accurate and informative in vitro assays. In perspective, integrated systems could be tailor-made to mimic specific physiological conditions of the local microenvironment and then analyze the response from screening specific drugs for more effective diagnostics, long-term prognostics, and disease intervention in personalized medicine.

Non-cytotoxic, temperature-responsive and antibacterial POEGMA based nanocomposite coatings with silver nanoparticles

Non-cytotoxic, temperature-responsive and antibacterial poly(di(ethylene glycol)methyl ether methacrylate) - POEGMA188 based nanocomposite coatings attached to a glass surface were successfully prepared using ATRP polymerization. The thickness, morphology and wettability of the resulting coatings were analyzed using ellipsometry, AFM and contact angle measurements, respectively. The strong impact of the thicknesses of the POEGMA188 grafted brush coatings and content of AgNPs on the morphology and temperature-induced wettability changes of the nanocomposite was demonstrated. In addition to the strong temperature-dependent antibacterial activity, the proposed nanocomposite coatings have no significant cytotoxic effect towards normal cells. Moreover, the slight anti-cancer effect of AgNPs may be suggested.

Multifunctional carbon nanotubes covalently coated with imine-based covalent organic frameworks: exploring structure-property relationships through nanomechanics

The assembly of 3-dimensional covalent organic frameworks on the surface of carbon nanotubes is designed and successfully developed for the first time via the hybridization of imine-based covalent organic frameworks (COF-300) and oxidized MWCNTs by one-pot chemical synthesis. The resulting hybrid material ox-MWCNTs@COF exhibits a conformal structure that consists of a uniform amorphous COF layer covering the ox-MWCNT surface. The measurements of individual hybrid nanotube mechanical strength performed with atomic force microscopy provide insights into their stability and resistance. The results evidence a very robust hybrid tubular nanostructure that preserves the benefits obtained from COF, such as CO2 adsorption. Further digestion of the organic structure with aniline enables the study of the interplay between the hybrid interface and its nanomechanics. This new hybrid nanomaterial presents exceptional mechanical and electrical properties, merging the properties of the CNT template and COF-300.

Targeted ErbB3 cancer therapy: A synergistic approach to effectively combat cancer

Surface modification of nanoparticles with aptamer is gaining popularity lately due to its selective targeting and low immunogenicity. In this study, sorafenib tosylate (SFB) was loaded in biodegradable PLGA nanoparticles prepared by solvent evaporation method. The surfaces of drug deprived and drug-loaded particles (PN and PNS, respectively) were coupled with aptamer to target ErbB3 using EDC/NHS chemical modification. Nanoparticles were characterized with regard to their size, shape and chemical composition by dynamic light scattering, atomic force microscopy, FTIR and elemental analysis respectively. To evaluate the particles in vitro cell culture studies were performed. Cell viability assay, pathway analysis and apoptosis assay showed cellular toxicity in the presence of aptamer in PNS-Apt (p < 0.001). Metastatic progression assay showed decreased cell migration in the presence of aptamer and SFB. Confocal laser scanning microscopy was used to visualize the receptor-mediated time-dependent intracellular uptake and distribution of the nanoparticles throughout the cytoplasm. The findings of the current study demonstrated the potential efficacy of the surface modified SFB-loaded particles against ErbB3.

Bio-nanotechnological advancement of orally administered insulin nanoparticles: Comprehensive review of experimental design for physicochemical characterization

Therapeutic proteins are labile macromolecules that are prone to degradation during production, freeze-drying and storage. Recent studies showed that nanoparticles can enhance the stability and oral bioavailability of encapsulated proteins. Several conventional approaches (enzyme inhibitors, mucoadhesive polymers) and novel strategies (surface modification, ligand conjugation, flash nano-complexation, stimuli-responsive drug delivery systems) have been employed to improve the physiochemical properties of nanoparticles such as size, zeta potential, morphology, polydispersity index, drug release kinetics and cell-targeting capacity. However, clinical translation of protein-based nanoparticle is limited due to poor experimental design, protocol non-compliance and instrumentation set-up that do not reflect the physiological conditions, resulting in difficulties in mass production of nanoparticles and waste in research funding. In order to address the above concerns, we conducted a comprehensive review to examine the experimental designs and conditions for physical characterization of protein-based nanoparticles. Reliable and robust characterization is essential to verify the cellular interactions and therapeutic potential of protein-based nanoparticles. Importantly, there are a number of crucial factors, which include sample treatment, analytical method, dispersants, sampling grid, staining, quantification parameters, temperature, drug concentration and research materials, should be taken into careful consideration. Variations in research protocol and unreasonable conditions that are used in optimization of pharmaceutical formulations can have great impact in result interpretation. Last but not least, we reviewed all novel instrumentations and assays that are available to examine mucus diffusion capacity, stability and bioactivity of protein-based nanoparticles. These include circular dichroism, fourier transform infrared spectroscopy, X-ray diffractogram, UV spectroscopy, differential scanning calorimetry, fluorescence spectrum, Förster resonance energy transfer, NMR spectroscopy, Raman spectroscopy, cellular assays and animal models.

Development and Mechanistic Insight into the Enhanced Cytotoxic Potential of Parvifloron D Albumin Nanoparticles in EGFR-Overexpressing Pancreatic Cancer Cells

Pancreatic cancer is one of the most lethal cancers, with an extremely poor prognosis. The development of more effective therapies is thus imperative. Natural origin compounds isolated from Plectranthus genus, such as parvifloron D (PvD), have cytotoxic and antiproliferative activity against human tumour cells. However, PvD is a very low water-soluble compound, being nanotechnology a promising alternative strategy to solve this problem. Therefore, the aim of this study was to optimize a nanosystem for preferential delivery of PvD to pancreatic tumour cells. Albumin nanoparticles (BSA NPs) were produced through a desolvation method. Glucose cross-linking and bioactive functionalization profiles of BSA platform were elucidated and analysed using static lattice atomistic simulations in vacuum. Using the optimized methodology, PvD was encapsulated (yield higher than 80%) while NPs were characterized in terms of size (100–400 nm) and morphology. Importantly, to achieve a preferential targeting to pancreatic cancer cells, erlotinib and cetuximab were attached to the PvD-loaded nanoparticle surface, and their antiproliferative effects were evaluated in BxPC3 and Panc-1 cell lines. Erlotinib conjugated NPs presented the highest antiproliferative effect toward pancreatic tumour cells. Accordingly, cell cycle analysis of the BxPC3 cell line showed marked accumulation of tumour cells in G1-phase and cell cycle arrest promoted by NPs. As a result, erlotinib conjugated PvD-loaded BSA NPs must be considered a suitable and promising carrier to deliver PvD at the tumour site, improving the treatment of pancreatic cancer.