Synergistic Effect of Bioactive Inorganic Fillers in Enhancing Properties of Dentin Adhesives-A Review

Microhardness, Surface Roughness, and Wear Resistance Enhancement of Reinforced Conventional Glass Ionomer Cement Using Fluorinated Graphene Oxide Nanosheets

OBJECTIVES

 Conventional glass ionomer cements (GICs) have been considered the most prevalent restorative material however; the reduced mechanical qualities and decreased wear resistance have been the main challenges facing their wide clinical application. This study was designed to assess the mechanical properties of fluorinated graphene (FG) oxide-modified conventional GIC.

MATERIALS AND METHODS

 Composites of FG/GIC samples were prepared using (Medifil from PROMEDICA, Germany, shade A3) at different concentrations (0wt%) control group and (1wt%, 2wt% and 3wt% FG) groups using cylindrical molds (3mm × 6mm). FG was prepared using hydrothermal technique and characterized using XPERT-PRO Powder Diffractometer system for X-ray diffraction analysis and JEOL JEM-2100 high resolution transmission electron microscope. Vickers' hardness and wear resistance of GI samples were measured. Mechanical abrasion was performed via three-body tooth brushing wear test using ROBOTA chewing simulator coupled with a thermocycling protocol (Model ACH-09075DC-T, AD-Tech Technology Co., Ltd., Leinfelden-Echterdingen, Germany).

STATISTICAL ANALYSIS

 Comparisons between groups with respect to normally distributed numeric variables were performed using one-way analysis of variance test followed by posthoc test. While paired t-test was utilized for comparing data within the same group.

RESULTS

The surface roughness values of GICs (1wt% FG) and (2wt% FG) composites were significantly lower than those of the control and 3wt%FG groups. Vickers' hardness numbers were significantly higher in FG/GICs composites than in the control group (p≤0.05).

CONCLUSION

 GIC/FG combinations have sufficient strength to resist the occlusion stresses with improved hardness as compared with conventional GIC. GIC/FG appeared to be a promising restorative material.

Unraveling Nanomaterials in Biomimetic Mineralization of Dental Hard Tissue: Focusing on Advantages, Mechanisms, and Prospects

The demineralization of dental hard tissue imposes considerable health and economic burdens worldwide, but an optimal method that can repair both the chemical composition and complex structures has not been developed. The continuous development of nanotechnology has created new opportunities for the regeneration and repair of dental hard tissue. Increasingly studies have reported that nanomaterials (NMs) can induce and regulate the biomimetic mineralization of dental hard tissue, but few studies have examined how they are involved in the different stages, let alone the relevant mechanisms of action. Besides their nanoscale dimensions and excellent designability, NMs play a corresponding role in the function of the raw materials for mineralization, mineralized microenvironment, mineralization guidance, and the function of mineralized products. This review comprehensively summarizes the advantages of NMs and examines the specific mineralization mechanisms. Design strategies to promote regeneration and repair are summarized according to the application purpose of NMs in the oral cavity, and limitations and development directions in dental hard tissue remineralization are proposed. This review can provide a theoretical basis to understand the interaction between NMs and the remineralization of dental hard tissue, thereby optimizing design strategy, rational development, and clinical application of NMs in the field of remineralization.

Dental biomaterials redefined: molecular docking and dynamics-driven dental resin composite optimization

BACKGROUND

Dental resin-based composites are widely recognized for their aesthetic appeal and adhesive properties, which make them integral to modern restorative dentistry. Despite their advantages, adhesion and biomechanical performance challenges persist, necessitating innovative strategies for improvement. This study addressed the challenges associated with adhesion and biomechanical properties in dental resin-based composites by employing molecular docking and dynamics simulation.

METHODS

Molecular docking assesses the binding energies and provides valuable insights into the interactions between monomers, fillers, and coupling agents. This investigation prioritizes SiO2 and TRIS, considering their consistent influence. Molecular dynamics simulations, executed with the Forcite module and COMPASS II force field, extend the analysis to the mechanical properties of dental composite complexes. The simulations encompassed energy minimization, controlled NVT and NPT ensemble simulations, and equilibration stages. Notably, the molecular dynamics simulations spanned a duration of 50 ns.

RESULTS

SiO2 and TRIS consistently emerged as influential components, showcasing their versatility in promoting solid interactions. A correlation matrix underscores the significant roles of van der Waals and desolvation energies in determining the overall binding energy. Molecular dynamics simulations provide in-depth insights into the mechanical properties of dental composite complexes. HEMA-SiO2-TRIS excelled in stiffness, BisGMA-SiO2-TRIS prevailed in terms of flexural strength, and EBPADMA-SiO2-TRIS offered a balanced combination of mechanical properties.

CONCLUSION

These findings provide valuable insights into optimizing dental composites tailored to diverse clinical requirements. While EBPADMA-SiO2-TRIS demonstrates distinct strengths, this study emphasizes the need for further research. Future investigations should validate the computational findings experimentally and assess the material's response to dynamic environmental factors.

Implications of graphene-based materials in dentistry: present and future

Since the advent of nanoscience, nanobiomaterials have been applied in the dental industry. Graphene and its derivatives have attracted the most interest of all of them due to their exceptional look, biocompatibility, multiplication differential, and antibacterial capabilities. We outlined the most recent developments about their applications to dentistry in our review. There is discussion of the synthesis processes, architectures, and characteristics of materials based on graphene. The implications of graphene and its counterparts are then meticulously gathered and described. Finally, in an effort to inspire more excellent research, this paper explores the obstacles and potential of graphene-based nanomaterials for dental aspects.

Can Graphene Pave the Way to Successful Periodontal and Dental Prosthetic Treatments? A Narrative Review

Graphene, as a promising material, holds the potential to significantly enhance the field of dental practices. Incorporating graphene into dental materials imparts enhanced strength and durability, while graphene-based nanocomposites offer the prospect of innovative solutions such as antimicrobial dental implants or scaffolds. Ongoing research into graphene-based dental adhesives and composites also suggests their capacity to improve the quality and reliability of dental restorations. This narrative review aims to provide an up-to-date overview of the application of graphene derivatives in the dental domain, with a particular focus on their application in prosthodontics and periodontics. It is important to acknowledge that further research and development are imperative to fully explore the potential of graphene and ensure its safe use in dental practices.

Mechanical and antibacterial properties of an experimental flowable composite containing Nb2O5 and NF_TiO2 nanoparticles

This study developed an experimental flowable composite incorporated with niobium pentoxide (Nb2O5) combined or not with titanium dioxide co-doped with fluorine and nitrogen (NF_TiO2) and evaluated the mechanical and antibacterial properties. The experimental flowable composite (TEGDMA + BisGMA 1:1 + 60%wt - inorganic filler - borosilicate 0.7 μm) was formulated according to the type and concentration of Nb2O5 and NF_TiO2 (0.5, 1, 1.5 and 2 wt%) or NF_TiO2 + Nb2O5 (0.25, 0.5, 0.75 and 1 wt% - 1:1). The control groups were formed by the experimental composite without the incorporation of Nb2O5 and/or NF_TiO2 (GC-E) and by a commercial flowable composite (GC). The characterization of the surface of the composite and its particles was carried out using scanning electron microscopy (SEM) and energy dispersive x-rays (EDX). Specimens were manufactured and subjected to mechanical tests of flexural strength (FS) (n = 12), flexural modulus (FM) (n = 12), roughness (Ra) (n = 10), microhardness (n = 10), and contact angle (n = 10); and, to evaluate the antibacterial activity, they were submitted to tests of biofilm formation against S. mutans (CFU/mL) (n = 5), biofilm biomass by dry weight (n = 5) and confocal laser microscopy (%LIVE/DEAD) (n = 5). Data were submitted to one-way ANOVA and Tukey's post-hoc and, those that were not homoscedastic, but with normality, were submitted to Welch's ANOVA and Games-Howell's post-hoc. Dunnet's test was used to compare the controls with the other experimental groups (α = 5). The Nb2O5 particles had an average size of 32.4 μm and the nanoparticles (NPs) of NF_TiO2, 10 nm. EDX analysis identified isolated peaks of N, F, Ti, and Nb confirming the presence of these particles in the resin matrix. The 1.5% NF_TiO2 group had a higher FS and FM than the controls (p < 0.05). GC showed higher microhardness between groups (p < 0.05). There was no difference between the experimental groups regarding contact angle and roughness (p > 0.05), except for GC, which had the highest Ra values and the lowest contact angle between groups (p < 0.05). Composites containing 0.5%, 1%, 1.5%, and 2% Nb2O5, 1%, 1.5%, and 2% NF_TiO2 and 2% Nb2O5 + NF_TiO2 showed lower biofilm formation (p < 0.05), lower total biofilm biomass (p < 0.05), and a higher percentage of dead cells (44%, 52%, 52%, 79%, 42% 43%, 62%, 65%, respectively) than GC and GC-E (5% and 1%, respectively). It is concluded that the incorporation of 1.5% NF_TiO2 promoted a greater FS and FM among the experimental composites and that the addition of Nb2O5 particles (0.5%, 1%, 1.5%, and 2%), NF_TiO2 (1%, 1.5% and 2%) and the combination Nb2O5 + NF_TiO2 (2%) showed significant antibacterial effects.

Fiber post bonding with beta-tricalcium phosphate incorporated root dentin adhesive. SEM, EDX, FTIR, rheometric and bond strength study

The aim was to formulate an experimental adhesive (EA) and added nanoparticles (NPs) of beta-tricalcium phosphate (β-TCP) to see the impact on pushout bond strength (PBS) and other mechanical properties. Three adhesives were prepared, including EA (control, without β-TCP NPs), 2.5%-β-TCP NPs containing adhesive (2.5%-NPA), and 5% β-TCP NPs containing adhesive (5%-NPA). For the characterization of the NPs, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy was accomplished. For the adhesive's characterization, rheological assessment, and degree of conversion (DC) analysis were performed. PBS of these adhesives against resin fiber post to root dentin, interfacial failure categories, and resin dentin interface analysis were also assessed. The β-TCP NPs were seen as agglomerated asymmetrical particles on SEM. These NPs were composed primarily of calcium (Ca), and phosphorus (P). Rheological evaluation of the adhesive's showed a drop in the viscosity of all adhesives at greater angular frequencies. The greatest DC was detected for the EA group (67.54 ± 7.9) followed by 2.5%-NPA group (45.32 ± 5.1), whereas the lowest DC values were seen for the 5%-NPA group (38.97 ± 6.5). Concerning PBS, the 2.5%-NPA revealed the highest values at the coronal (12.81 ± 3.0) and middle (8.50 ± 2.3) sections, whereas, for the apical section, the highest PBS values were seen for the 5%-NPA (4.9 ± 1.6). Most of the failures for all adhesive groups were seen at the adhesive-dentin interface (cohesive type failures) for all root segments (coronal, middle, and apical). The resin-dentin interface analysis verified hybrid layer and resin tag formation for all adhesives, but the presence of dispersed β-TCP NPs was only seen in the two NP-reinforced adhesives. The adding of β-TCP NPs in the adhesive could be beneficial as it could improve its PBS. Suitable rheological properties and dentin interaction were also observed for NP-reinforced adhesives. A reduced DC was seen for both β-TCP NP-containing adhesives as compared to the EA. RESEARCH HIGHLIGHTS: Experimental adhesives were reinforced with beta-tricalcium phosphate (β-TCP) nanocrystals. The β-TCP NPs were seen as agglomerated asymmetrical particles on SEM. These NPs were composed primarily of calcium (Ca), and phosphorus (P). β-TCP adhesives demonstrated superior pushout bond strength and a drop in the adhesive viscosity at greater angular frequencies compared to control adhesive. The greatest DC was detected for the EA group followed by 2.5%- β-TCP group, whereas the lowest DC values were for the 5%- β-TCP group.

Physicochemical Properties of Novel Copolymers of Quaternary Ammonium UDMA Analogues, Bis-GMA, and TEGDMA

This study aimed to elucidate the physicochemical properties of copolymers comprising 40 wt.% bisphenol A glycerolate dimethacrylate (Bis-GMA), 40 wt.% quaternary ammonium urethane-dimethacrylate analogues (QAUDMA-m, where m corresponds to the number of carbon atoms in the N-alkyl substituent), and 20 wt.% triethylene glycol dimethacrylate (TEGDMA) copolymers (BG:QAm:TEGs). The BG:QAm:TEG liquid monomer compositions and reference compositions (40 wt.% Bis-GMA, 40 wt.% urethane-dimethacrylate (UDMA), 20 wt.% TEGDMA (BG:UD:TEG) and 60 wt.% Bis-GMA, 40 wt.% TEGDMA (BG:TEG)) were characterized in terms of their refractive index (RI) and monomer glass transition temperature (Tgm) and then photocured. The resulting copolymers were characterized in terms of the polymer glass transition temperature (Tgp), experimental polymerization shrinkage (Se), water contact angle (WCA), water sorption (WS), and water solubility (SL). The prepared BG:QAm:TEG liquid monomer compositions had RI in the range 1.4997-1.5129, and Tgm in the range -52.22 to -42.12 °C. The BG:QAm:TEG copolymers had Tgp ranging from 42.21 to 50.81 °C, Se ranging from 5.08 to 6.40%, WCA ranging from 81.41 to 99.53°, WS ranging from 25.94 to 68.27 µg/mm3, and SL ranging from 5.15 to 5.58 µg/mm3. Almost all of the developed BG:QAm:TEGs fulfilled the requirements for dental materials (except BG:QA8:TEG and BG:QA10:TEG, whose WS values exceeded the 40 µg/mm3 limit).

Influence of carbon and graphene oxide nanoparticle on the adhesive properties of dentin bonding polymer: A SEM, EDX, FTIR study

OBJECTIVE

This study was aimed at including 2.5 wt.% of carbon nanoparticles (CNPs) and graphene oxide NPs (GNPs) in a control adhesive (CA) and then investigate the effect of this inclusion on their mechanical properties and its adhesion to root dentin.

MATERIALS AND METHODS

Scanning electron microscopy and energy dispersive X-ray (SEM-EDX) mapping were conducted to investigate the structural features and elemental distribution of CNPs and GNPs, respectively. These NPs were further characterized by Raman spectroscopy. The adhesives were characterized by evaluating their push-out bond strength (PBS), rheological properties, degree of conversion (DC) investigation, and failure type analysis.

RESULTS

The SEM micrographs revealed that the CNPs were irregular and hexagonal, whereas the GNPs were flake-shaped. EDX analysis showed that carbon (C), oxygen (O), and zirconia (Zr) were found in the CNPs, while the GNPs were composed of C and O. The Raman spectra for CNPs and GNPs revealed their characteristic bands (CNPs-D band: 1334 cm-1, GNPs-D band: 1341 cm-1, CNPs-G band: 1650 cm-1, and GNPs-G band: 1607 cm-1). The testing verified that the highest bond strength to root dentin were detected for GNP-reinforced adhesive (33.20 ± 3.55 MPa), trailed closely by CNP-reinforced adhesive (30.48 ± 3.10 MPa), while, the CA displayed lowest values (25.11 ± 3.60 MPa). The inter-group comparisons of the NP-reinforced adhesives with the CA revealed statistically significant results (p < 0.01). Failures of adhesive nature were most common in within the adhesives and root dentin. The rheological assessment results demonstrated a reduced viscosity for all the adhesives observed at advanced angular frequencies. All the adhesives verified suitable dentin interaction shown by hybrid layer and appropriate resin tag development. A reduced DC was perceived for both NP-reinforced adhesives, compared to the CA.

CONCLUSION

The present study's findings have demonstrated that 2.5% GNP adhesive revealed the highest, suitable root dentin interaction, and acceptable rheological properties. Nevertheless, a reduced DC was observed (matched with the CA). Prospective studies probing the influence of diverse concentrations of filler NPs on the adhesive's mechanical properties to root dentin are recommended.

Dental Adhesives-Surface Modifications of Dentin Structure for Stable Bonding

The latest advancements in dentin bonding have focused on strategies to impair degradation mechanisms in order to extend the longevity of bonded interfaces. Protease inhibitors can reduce collagen degradation within the hybrid layer (HL). Collagen cross-linkers allow better adhesive infiltration and also inhibit proteases activity. Particles added to adhesive can promote mineral precipitation within the HL, reducing nanoleakage and micropermeability, besides possible antimicrobial and enzymatic inhibition effects. Most of these approaches are still experimental, and aspects of the adhesive under the clinician's control are still determinant for the long-term stability of adhesive restorations.

Biomaterials for Tissue Engineering Applications and Current Updates in the Field: A Comprehensive Review

Tissue engineering has emerged as an interesting field nowadays; it focuses on accelerating the auto-healing mechanism of tissues rather than organ transplantation. It involves implanting an In Vitro cultured initiative tissue or a scaffold loaded with tissue regenerating ingredients at the damaged area. Both techniques are based on the use of biodegradable, biocompatible polymers as scaffolding materials which are either derived from natural (e.g. alginates, celluloses, and zein) or synthetic sources (e.g. PLGA, PCL, and PLA). This review discusses in detail the recent applications of different biomaterials in tissue engineering highlighting the targeted tissues besides the in vitro and in vivo key findings. As well, smart biomaterials (e.g. chitosan) are fascinating candidates in the field as they are capable of elucidating a chemical or physical transformation as response to external stimuli (e.g. temperature, pH, magnetic or electric fields). Recent trends in tissue engineering are summarized in this review highlighting the use of stem cells, 3D printing techniques, and the most recent 4D printing approach which relies on the use of smart biomaterials to produce a dynamic scaffold resembling the natural tissue. Furthermore, the application of advanced tissue engineering techniques provides hope for the researchers to recognize COVID-19/host interaction, also, it presents a promising solution to rejuvenate the destroyed lung tissues.

The Effect of Dentifrice on Micro-Hardness, Surface Gloss, and Micro-Roughness of Nano Filled Conventional and Bulk-Fill Polymer Composite-A Micro Indentation and Profilometric Study

The aim of the present study was to evaluate the effect of brushing with two whitening dentifrices (Colgate Optic White (COW) and Colgate Optic White Charcoal (COC)) on surface gloss, micro-roughness, and micro-hardness of nanostructured hybrid conventional (Z350) and bulk-fill (Tetric N Ceram bulk-fill) polymer composite. In total, 96 disk samples using two nano-hybrid composite polymers (Z350 and Tetric N Ceram Bulk-fill) were prepared. All specimens were exposed to two different dentifrices (COW and COC), resulting in four main subgroups in the study. Specimens were assessed for surface gloss, micro-roughness (Ra), and micro-hardness using standardized methodology. Means and standard deviations of properties compared using paired t-test, one-way and two-way ANOVA, and post hoc test. The presence of dentifrices did not show any significant difference in micro-hardness values of Z350 (p > 0.05), whereas micro-hardness of bulk-fill composite significantly reduced on dentifrices exposure (p ≤ 0.05). Bulk-fill polymer composite showed significant reduction in gloss after dentifrice exposure (p < 0.05), however, Z350 showed no significant loss of gloss due to dentifrices (p > 0.05). A significant increase in Ra was observed for both resin materials after exposure to dentifrices (COC and COW). Conventional resin composite (Z350) showed comparable surface hardness and gloss before and after dentifrice exposure, however, micro-roughness increased significantly due to dentifrice exposure. Bulk-fill resin (Tetric N Ceram) showed significant loss of micro-hardness and gloss and increase in micro-roughness on dentifrice exposure. Conventional nano-hybrid composite polymer showed better durability in resisting loss of surface properties compared to bulk-fill resin polymer in the present experiment.

Recent Advances in Direct Adhesive Restoration Resin-Based Dental Materials With Remineralizing Agents

Resin-based dental materials are popular restorative materials especially in direct adhesive restoration because of the excellent mechanical and esthetic properties. Toward the realization of minimally invasive dental procedures, direct composite resin adhesive restoration has become the main treatment for dental defects. In addition, for caries-affected dentin close to the pulp, conservation remineralization has been advocated to save the living pulp. However, the resin–dentin interface can be destabilized by various factors, especially the enzymatic degradation of collagen fibrils within the hybrid layer and polymer hydrolysis. Furthermore, for resin-based restorative materials, the marginal gap remains a major problem that can lead to the occurrence of secondary caries. To address these issues, research efforts have focused on the remineralization of mineral-depleted dental hard tissues using remineralizing bioactive substances. In this review, we first described various bioactive agents with remineralizing properties. Furthermore, we discussed recent advances in resin-based dental materials for enamel or dentin remineralization. Finally, we examined the current challenges and prospects of these emerging materials. This work aims to provide a theoretical foundation for the future development of resin-based dental materials in direct adhesive restoration with remineralizing agents.

Graphene-Based Nanomaterials for Dental Applications: Principles, Current Advances, and Future Outlook

With the development of nanotechnology, nanomaterials have been used in dental fields over the past years. Among them, graphene and its derivatives have attracted great attentions, owing to their excellent physicochemical property, morphology, biocompatibility, multi-differentiation activity, and antimicrobial activity. In our review, we summarized the recent progress about their applications on the dentistry. The synthesis methods, structures, and properties of graphene-based materials are discussed. Then, the dental applications of graphene-based materials are emphatically collected and described. Finally, the challenges and outlooks of graphene-based nanomaterials on the dental applications are discussed in this paper, aiming at inspiring more excellent studies.

Influence of Concentration Levels of β-Tricalcium Phosphate on the Physical Properties of a Dental Adhesive

Our study assessed the influence of integrating 5% and 10% tricalcium phosphate (β-TCP-Ca₃(PO₄)₂.) nanoparticles into a dental adhesive on the adhesive’s bonding. To evaluate the filler nanoparticles, scanning electron microscopy (SEM), Energy Dispersive X-Ray (EDX) spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and micro-Raman spectroscopy techniques were used. Shear Bond strength (SBS) testing, degree of conversion (DC) analysis, investigation of the adhesive–dentin interface, and biofilm experiments were conducted. The SEM micrographs revealed non-uniform agglomerates, while the EDX demonstrated the existence of oxygen ‘O’ (24.2%), phosphorus ‘P’ (17.4%) and calcium ‘Ca’ (60.1%) in the β-TCP nanoparticles. The FTIR and micro-Raman spectra indicated characteristic bands for β-TCP containing materials. The 10 wt.% β-TCP adhesive presented the highest SBS values (NTC-10 wt.% β-TCP: 33.55 ± 3.73 MPa, TC-10 wt.% β-TCP: 30.50 ± 3.25 MPa), followed by the 5 wt.% β-TCP adhesive (NTC-5 wt.% β-TCP: 32.37 ± 3.10 MPa, TC-5 wt.% β-TCP: 27.75 ± 3.15 MPa). Most of the detected failures after bond strength testing were adhesive in nature. The β-TCP adhesives demonstrated suitable dentin interaction by forming a hybrid layer (with few or no gaps) and resin tags. The β-TCP adhesives (10 wt.%) revealed lower DC values compared to control. The incorporation of 5 and 10 wt.% concentrations of β-TCP particles resulted in an increase in SBS values. A linear decline in DC values was witnessed when the nanoparticle concentration was increased. Further research focusing on exploring the influence of higher filler concentrations on adhesive’s properties is recommended.

Adhesive Bond Integrity of Experimental Zinc Oxide Nanoparticles Incorporated Dentin Adhesive: An SEM, EDX, μTBS, and Rheometric Analysis

OBJECTIVE

Our study is aimed at preparing an experimental adhesive (EA) and assessing the influence of adding 5-10 wt.% concentrations of zinc oxide (ZnO) nanoparticles on the adhesive's mechanical properties.

METHODS

Field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) spectroscopy were employed to investigate the morphology and elemental distribution of the filler nanoparticles. To examine the adhesive properties, microtensile bond strength (μTBS) testing, an investigation of the rheological properties, degree of conversion (DC), and analysis of the interface between the adhesive and dentin were carried out.

RESULTS

The SEM micrographs of ZnO nanoparticles demonstrated spherical agglomerates. The EDX plotting confirmed the incidence of Zn and oxygen (O) in the ZnO nanoparticles. The highest μTBS was observed for nonthermocycled (NTC) 5 wt.% ZnO group (32.11 ± 3.60 MPa), followed by the NTC-10 wt.% ZnO group (30.04 ± 3.24 MPa). Most of the failures observed were adhesive in nature. A gradual reduction in the viscosity was observed at higher angular frequencies, and the addition of 5 and 10 wt.% ZnO to the composition of the EA lowered its viscosity. The 5 wt.% ZnO group demonstrated suitable dentin interaction by showing the formation of resin tags, while for the 10 wt.% ZnO group, compromised resin tag formation was detected. DC was significantly higher in the 0% ZnO (EA) group.

CONCLUSION

The reinforcement of the EA with 5 and 10 wt.% concentrations of ZnO nanoparticles produced an improvement in the adhesive's μTBS. However, a reduced viscosity was observed for both nanoparticle-reinforced adhesives, and a negotiated dentin interaction was seen for 10 wt.% ZnO adhesive group. Further research exploring the influence of more filler concentrations on diverse adhesive properties is recommended.

Investigating the mechanophysical and biological characteristics of therapeutic dental cement incorporating copper doped bioglass nanoparticles

OBJECTIVE

This study was investigated the mechanophysical properties of zinc phosphate cement (ZPC) with or without the copper doped bioglass nanoparticles (Cu-BGn) and their biological effect on dental pulp human cells and bacteria.

MATERIALS AND METHODS

Cu-BGn were synthesized and characterized firstly and then, the experimental (Cu-ZPC) and control (ZPC) samples were fabricated with similar sizes and/or dimensions (diameter: 4 mm and height: 6 mm) based on the International Organization of Standards (ISO). Specifically, various concentrations of Cu-BGn were tested, and Cu-BGn concentration was optimized at 2.5 wt% based on the film thickness and overall setting time. Next, we evaluated the mechanophysical properties such as compressive strength, elastic modulus, hardness, and surface roughness. Furthermore, the biological behaviors including cell viability and odontoblastic differentiation by using dental pulp human cells as well as antibacterial properties were investigated on the Cu-ZPC. All data were analyzed statistically using SPSS® Statistics 20 (IBM®, USA). p < 0.05 (*) was considered significant, and 'NS' represents nonsignificant.

RESULTS

Cu-BGn was obtained via a sol-gel method and added onto the ZPC for fabricating a Cu-ZPC composite and for comparison, the Cu-free-ZPC was used as a control. The film thickness (≤ 25 µm) and overall setting time (2.5-8 min) were investigated and the mechanophysical properties showed no significance ('NS') between Cu-ZPC and bare ZPC. However, cell viability and odontoblastic differentiation, alkaline phosphate (ALP) activity and alizarin red S (ARS) staining were highly stimulated in the extracts from the Cu-ZPC group compared to the ZPC group. Additionally, the antibacterial test showed that the Cu-ZPC extracts were more effective than the ZPC extracts (p < 0.05).

SIGNIFICANCE

Cu-ZPC showed adequate mechanophysical properties (compressive strength, hardness, and surface roughness) and enhanced odontoblastic differentiation as well as antibacterial properties compared to the ZPC-only group. Based on the findings, the fabricated Cu-ZPC might have the potential for use in the field of dental medicine and clinical applications.

Influence of TiO2 and ZrO2 Nanoparticles on Adhesive Bond Strength and Viscosity of Dentin Polymer: A Physical and Chemical Evaluation

The present study aimed to formulate an experimental adhesive (EA) and reinforce it with 5 wt.% titanium dioxide (TiO₂) or zirconium oxide (ZrO₂) to yield 5% TiO₂ and 5% ZrO₂ adhesives, respectively, and then analyze the impact of this reinforcement on various mechanical properties of the adhesives. The EA contained a blend of monomers such as bisphenol A glycol dimethacrylate (BisGMA), triethylene glycol dimethacrylate (TEGDMA), 2-hydroxyethyl methacrylate (HEMA), and ethyl 4-dimethylamino benzoate and camphorquinone. The EA included ethyl 4-dimethylamino benzoate and camphorquinone photo-initiators, and diphenyliodonium hexafluorophosphate (DPIHP) was also included to act as an electron initiator. The TiO₂ and ZrO₂ nanoparticles were incorporated into the EA post-synthesis. To characterize the filler nanoparticles, scanning electron microscopy (SEM) and line-energy dispersive X-ray (EDX) spectroscopy were performed. The adhesives were characterized by analyzing their rheological properties, shear-bond strength (SBS), and interfacial failure types. Further, the resin-dentin interface was also analyzed via SEM. The TiO₂ nanoparticles were spherically shaped on the SEM micrographs, while the ZrO₂ nanoparticles were seen as non-uniformly shaped agglomerates. The EDX mapping demonstrated the presence of Ti and oxygen for TiO₂ and Zr and oxygen for the ZrO₂ nanoparticles. Both 5% TiO₂ and 5% ZrO₂ adhesives revealed decreased viscosity as compared with the EA. The 5% TiO₂ adhesive demonstrated higher SBS values for both non-thermocycled (NTC) and thermocycled samples (NTC: 25.35 ± 1.53, TC: 23.89 ± 1.95 MPa), followed by the 5% ZrO₂ adhesive group (NTC: 23.10 ± 2.22, TC: 20.72 ± 1.32 MPa). The bulk of the failures (>70%) were of adhesive type in all groups. The SEM analysis of the resin-dentin interface revealed the development of a hybrid layer and resin tags (of variable depth) for the EA and 5% TiO₂ groups. However, for the 5% ZrO₂ group, the hybrid layer and resin tag establishment appeared compromised. Reinforcement of the EA with TiO₂ or ZrO₂ caused an increase in the adhesive's SBS (with the 5% TiO₂ group demonstrating the highest values) in comparison with the EA (without nanoparticles). However, both nanoparticle-containing adhesives revealed decreased viscosity compared with the EA (without nanoparticles). Further studies investigating the impact of diverse filler concentrations on the properties of adhesives are suggested.

Influence of Conventional, CAD-CAM, and 3D Printing Fabrication Techniques on the Marginal Integrity and Surface Roughness and Wear of Interim Crowns

The aim is to assess the influence of fabrication techniques—conventional (CN), CAD-CAM (CC), and 3D printing (3D)—on the marginal fit, adaptation, surface roughness, and wear of interim restorations of crowns. Thirty interim crowns were fabricated using CN, CC, and 3D techniques. Sixty discs were fabricated to evaluate surface wear and surface roughness properties, with 10 disc samples in each group (n = 10). Internal adaptation and marginal integrity of interim crowns were analyzed with micro CT to detect microgaps at selected points. Average surface micro-roughness (Ra) was calculated in micrometers (μm) using an optical non-contact surface microscope under cyclic loading. Surface wear was evaluated by surface area measurements (mm3) using a micro CT. Analysis of variance (ANOVA) and Tukey’s post hoc comparison tests with Pearson correlation were performed for data analysis. The highest adaptation means were for CN (269.94 ± 64 μm), and the lowest mean value was observed for 3D (197.82 ± 11.72 μm) crowns. CN and CC specimens showed comparable adaptation (p > 0.05), which were significantly higher (p < 0.05) than 3D crowns. CN crowns showed significantly higher marginal misfit compared to 3D (p < 0.05) and CC (p < 0.05) crowns. The highest mean surface roughness was observed in the 3D crowns (5.61 ± 0.33 µm), whereas the lowest was found in CC crowns (3.28 ± 0.34 µm). Better restoration Ra was observed using the CC method followed by CN. CN had the highest wear (17.79 ± 2.78 mm3), and the lowest wear was observed in the 3D (10.81 ± 2.00 mm3) specimen. Low surface wear was observed using 3D printing, followed by CN and CC techniques. The printed specimen showed comparable outcomes to CAD-CAM restoration; however, they were better than CN restoration. A positive correlation between adaptation and surface roughness was observed, indicating an effect of the fabrication technique on material physical property.

Application of β-Tricalcium Phosphate in Adhesive Dentin Bonding

The study aimed at synthesizing β-tricalcium phosphate (β-TCP) nanoparticles and comparing the mechanical properties and dentin interaction of two adhesives: experimental adhesive (EA) and EA with 5 wt.% β-TCP nanoparticles (β-TCP-5%). These filler nanoparticles were synthesized and then characterized with scanning electron microscopy (SEM) and micro-Raman spectroscopy. The β-TCP nanoparticles were incorporated in the adhesives to form two groups: gp-1: EA (control) and gp-2: β-TCP-5%. These adhesives were characterized by SEM, energy-dispersive X-ray (EDX) spectroscopy and were also assessed for their micro-tensile bond strength (μTBS) with (TC) and without thermocycling (NTC). Fourier Transform Infrared (FTIR) spectroscopy was performed to evaluate the degree of conversion (DC) of two adhesives. The β-TCP filler was seen as irregularly shaped agglomerates on SEM. The micro-Raman spectra revealed characteristic peaks associated with β-TCP nanoparticles. Both adhesives presented suitable dentin interaction, which was demonstrated by the formation of resin tags of variable depths. The EDX analysis verified the existence of calcium (Ca) and phosphate (P) for the β-TCP-5% group. The greatest μTBS values were shown by β-TCP-5% group samples when they were non-thermocycled (NTC) (β-TCP-5%-NTC: 34.11 ± 3.46) followed by the thermocycled (TC) samples of the same group (β-TCP-5%-TC: 30.38 ± 3.66), compared with the EA group. Although the DC presented by β-TCP-5% group was comparable to the EA group, it was still lower. The addition of β-TCP nanoparticles in the adhesive improved its μTBS and resulted in a suitable dentin interaction, seen in the form of hybrid layer and resin tag formation. Nonetheless, a decreased DC was observed for the β-TCP-5% adhesive. Future studies probing the effect of different filler concentrations on various properties of the adhesive are warranted.

Cytotoxic Evaluation and Determination of Organic and Inorganic Eluates from Restorative Materials

Over the last years, diverse commercial resin-based composites have dominated as dental filling materials. The purpose of the present study was to determine organic and inorganic eluates from five restorative materials using GC/MS and ICP–OES and to compare the effect on cell survival of human gingival fibroblasts of a conventional and a bioactive resin. Five commercially available restorative materials were employed for this study: Activa^TM Bioactive Restorative, ENA HRi, Enamel plus HRi Biofunction, Fuji II LC Capsule, and Fuji IX Capsule. Disks that were polymerized with a curing LED light or left to set were immersed in: 1 mL methanol or artificial saliva for GC/MS analysis, 5mL deionized water for ICP–OES, and 5mL of culture medium for cell viability. Cell viability was investigated with a modified staining sulforhodamine B assay.The following organic substances were detected: ACP, BHT, BPA, 1,4-BDDMA, CQ, DBP, DMABEE, HEMA, MCE, MeHQ, MOPA, MS, TMPTMA, and TPSb and the ions silicon, aluminum, calcium, sodium, and barium. Activa Bioactive Restorative was found to be biocompatible. Elution of organic substances depended on material’s composition, the nature of the solvent and the storage time. Ions’ release depended on material’s composition and storage time. The newly introduced bioactive restorative was found to be more biocompatible.