Chitosan: Gels and Interfacial Properties

Coating based on chitosan/vancomycin nanoparticles: Patterns of formation in a water-carbon dioxide biphase system and in vivo stability

The patterns of formation of chitosan nanoparticles doped with vancomycin and coatings based on them in carbonate solutions have been investigated for the first time in this study. Using a technique of radioactive indicators, it was found that at a CO2 pressure of 30 MPa, the yield of the nanoparticles was ∼85 %, and a maximum antibiotic encapsulation efficiency of ∼30 % was achieved. By spectrophotometric and high-resolution microscopy, it was found that the coating of stabilized xenopericardial tissue of bioprosthetic heart valve, based on chitosan nanoparticles doped with vancomycin with a zeta potential |ζ| ∼20 mV completely covers collagen fibers by depositing about 60 nm nanoparticles onto them under direct deposition from carbonic acid at a pressure of 30 MPa CO2. The coating preserves the mechanical strength characteristics of collagen tissue and completely suppresses the growth of S. aureus pathogenic biofilm. This is consistent with the observed increase in antibiotic release of 15 % when the medium was acidified. Histological study demonstrated that the structure of pericardial tissues was not significantly altered by the deposition nanoparticles from carbonic acid. It was found that the rate of biodegradation of polymers and vancomycin in the coating differs by half (16 weeks for the rat model). A significantly lower degradation rate of antibiotics (∼50 % of vancomycin total remaining mass and ∼25 % of chitosan) was associated with its reliable encapsulation into nanoparticles.

Influence of furcellaran and safflower oil concentration on the properties of model emulgel systems

The aim of this study was to investigate the effect of varying concentrations of furcellaran (FUR) and safflower (Carthamus Tinctorius) oil on the functional properties of emulgels as potential carriers of bioactive substances. The textural, mechanical, thermal and structural properties of twenty different formulations were characterised. The pH stability and zeta-potential of the emulgels was also examined. It was found clear correlation between gelling agent and oil fraction content and investigated properties. The hardness, strength, thermal stability expressed as melting point of the investigated systems increased with increasing concentration of the furcellaran and decreasing proportion of safflower oil, which indicated a significant weakening of the structure as a result of the addition of the oil fraction. Stored under refrigeration, emulgels appeared to be relatively stable showing a slight decrease in pH values after 7 days. Swelling ratio (SW) of emulgels increased with increasing both, polysaccharide and oil content, in emulgels. Based on the microstructure analyses, it can also be concluded that only part of the added safflower oil chemically bound to the functional groups of the polysaccharide, while the vast majority of it was only physically immobilized in the furcellaran matrix. Colour of furcellaran - safflower oil emulsion gels depended largely on the amount of oil fraction. The presented research demonstrating the wide spectrum of functional properties of polysaccharide-oil systems is a first step to developing a carrier composition for lipophilic compounds at further stages of research.

Re-entrant phase transitions in Laponite/Gum Arabic nanocomposites

A re-entrant gel transition is observed in a discotic clay, Laponite (Lap) aqueous suspensions with the addition of a complex polysaccharide, Gum Arabic (GA). For fixed concentrations of Lap (1-3 % w/v) and at low GA concentrations (CGA < 10 % w/v), the composites exhibit gel behaviour, while the suspensions undergo liquid phase separation for intermediate GA concentrations (10 % w/v < CGA < 20 % w/v). Gel behaviour is again observed in the samples at even higher GA concentrations (CGA > 30 % w/v). Here, we identify a thermodynamic phase transition in Lap/GA mixtures that is caused by a variation in GA content. The viscoelastic characteristics, phase transitions, and gelation kinetics of the Lap/GA mixtures have been studied by employing rheology, small-angle X-ray scattering, and optical investigations. Reduction of the negative values of zeta-potential and growth of the composite system's hydrodynamic size indicated the presence of interactions in Lap/GA mixtures. The phase diagram enables the apparent interactions and phase transitions between the nanoplatelets and the complex polysaccharides. Thus, our study provides new perspectives on a nanocomposite's tuneable rheological and structural features.

Rheological Characterization of Genipin-Based Crosslinking Pigment and O-Carboxymethyl Chitosan-Oxidized Hyaluronic Acid In Situ Formulable Hydrogels

The aim of this study was to develop a material capable of rapidly absorbing bodily fluids and forming a resilient, adhesive, viscoelastic hydrogel in situ to prevent post-surgical adhesions. This material was formulated using O-carboxymethyl chitosan (O-CMCS), oxidized hyaluronic acid (OHA), and a crosslinking pigment derived from genipin and glutamic acid (G/GluP). Both crosslinked (O-CMCS/OHA-G/GluP) and non-crosslinked hydrogels (O-CMCS/OHA) were evaluated using a HAAKE™ MARS™ rheometer for their potential as post-surgical barriers. A rheological analysis, including dynamic oscillatory measurements, revealed that the crosslinked hydrogels exhibited significantly higher elastic moduli (G'), indicating superior gel formation and mechanical stability compared to non-crosslinked hydrogels. The G/GluP crosslinker enhanced gel stability by increasing the separation between G' and G″ and achieving a lower loss tangent (tan δ < 1.0), indicating robustness under dynamic physiological conditions. The rapid hydration and gelation properties of the hydrogels underscore their effectiveness as physical barriers. Furthermore, the O-CMCS/OHA-G/GluP hydrogel demonstrated rapid self-healing and efficient application via spraying or spreading, with tissue adherence and viscoelasticity to facilitate movement between tissues and organs, effectively preventing adhesions. Additionally, the hydrogel proved to be both cost effective and scalable, highlighting its potential for clinical applications aimed at preventing post-surgical adhesions.

Valorization of Seafood Waste for Food Packaging Development

Packaging plays a crucial role in protecting food by providing excellent mechanical properties as well as effectively blocking water vapor, oxygen, oil, and other contaminants. The low degradation of widely used petroleum-based plastics leads to environmental pollution and poses health risks. This has drawn interest in renewable biopolymers as sustainable alternatives. The seafood industry generates significant waste that is rich in bioactive substances like chitin, chitosan, gelatins, and alginate, which can replace synthetic polymers in food packaging. Although biopolymers offer biodegradability, biocompatibility, and non-toxicity, their films often lack mechanical and barrier properties compared with synthetic polymer films. This comprehensive review discusses the chemical structure, characteristics, and extraction methods of biopolymers derived from seafood waste and their usage in the packaging area as reinforcement or base materials to guide researchers toward successful plastics replacement and commercialization. Our review highlights recent advancements in improving the thermal durability, mechanical strength, and barrier properties of seafood waste-derived packaging, explores the mechanisms behind these improvements, and briefly mentions the antimicrobial activities and mechanisms gained from these biopolymers. In addition, the remaining challenges and future directions for using seafood waste-derived biopolymers for packaging are discussed. This review aims to guide ongoing efforts to develop seafood waste-derived biopolymer films that can ultimately replace traditional plastic packaging.

Development, Characterization, and Evaluation of Potential Systemic Toxicity of a Novel Oral Melatonin Formulation

The need to create safe materials for biomedical and pharmaceutical applications has become a significant driving force for the development of new systems. Therefore, a chitosan-coated copolymer of itaconic acid, acrylic acid, and N-vinyl caprolactam (IT-AA-NVC) was prepared by radical polymerization and subsequent coating via nanoprecipitation to give a system capable of sustained delivery of melatonin. Although melatonin brings undoubted benefits to the human body, aspects of the optimal dose, route, and time of administration for the obtaining of suitable treatment outcomes remain under discussion. The entrapment of melatonin in biocompatible polymeric systems can prevent its oxidation, decrease its toxicity, and provide an increased half-life, resulting in an enhanced pharmacokinetic profile with improved patient compliance. The structures of the biopolymer and conjugate were proven by FTIR, thermal properties were tested by DSC, and the morphologies were followed by SEM. The loading efficiency and in vitro release profile were studied by means of HPLC, and a delayed release profile with an initial burst was obtained. The potential systemic toxicity of the formulation was studied in vivo; a mild hepatotoxicity was observed following administration of the melatonin-loaded formulation to mice, both by histopathology and blood clinical biochemistry. Histopathology showed a mild nephrotoxicity as well; however, kidney clinical biochemistry did not support this.

Gemcitabine-loaded chitosan nanoparticles enhanced apoptotic and ferroptotic response of gemcitabine treatment alone in the pancreatic cancer cells in vitro

Gemcitabine (GEM) is a first-line treatment for pancreatic ductal adenocarcinoma (PDAC) patients, causing side effects and poor overall survival. Eighty percent of patients often develop resistance rapidly to GEM. Developing therapeutic approaches and increasing sensitivity to gemcitabine in PDAC has become one of the challenges in cancer research. We synthesized GEM-loaded NPs prepared with a method that combines ultrasonication and ionotropic gelation to overcome GEM-related limitations in PDAC. CFPAC-1 cells were treated with increased concentrations of GEM, empty chitosan, and GEM-loaded NPs (0.66, 1.32, 2.64, 5.32 µg/ml) for up to 48 h. Empty chitosan NPs did not show toxicity on L929 cells. Antioxidant enzyme activities, including glucose 6-phosphate dehydrogenase (G6PD), 6-phosphogluconate dehydrogenase (6-PGD), glutathione reductase (GR), glutathione s-transferase (GST), and glutathione peroxidase (GPx), significantly reduced in GEM-loaded NPs compared to the GEM associated with increased oxidative stress, PPP, and glycolysis. Bcl-xL, NOXA/mcl-1, and Ca2+ levels significantly increased in GEM-loaded NP-administered cells compared to the GEM and control groups. In contrast, JNK, p38, STAT3, Akt, and CREB levels significantly decreased in the GEM-loaded NP group, addressing enhanced apoptotic response compared to the GEM alone. Increased ferroptosis activity in GEM-loaded NP-administered groups has been validated via decreased antioxidant enzyme activities, increased cytosolic Fe, Zn, Mg, and Mn levels, and reduced GPx activity compared to the GEM and control groups. For the first time in the literature, we showed biocompatible GEM-loaded NPs enhanced apoptotic and ferroptotic response in CFPAC-1 cells via downregulation of antioxidant, glycolysis, and PPP metabolism compared to the GEM alone.

Effect of biopolymer chitosan on manganese immobilization improvement by microbial‑induced carbonate precipitation

Microbially induced carbonate precipitation (MICP), as an eco-friendly and promising technology that can transform free metal ions into stable precipitation, has been extensively used in remediation of heavy metal contamination. However, its depressed efficiency of heavy metal elimination remains in question due to the inhibition effect of heavy metal toxicity on bacterial activity. In this work, an efficient, low-cost manganese (Mn) elimination strategy by coupling MICP with chitosan biopolymer as an additive with reduced treatment time was suggested, optimized, and implemented. The influences of chitosan at different concentrations (0.01, 0.05, 0.10, 0.15 and 0.30 %, w/v) on bacterial growth, enzyme activity, Mn removal efficiency and microstructure properties of the resulting precipitation were investigated. Results showed that Mn content was reduced by 94.5 % within 12 h with 0.15 % chitosan addition through adsorption and biomineralization as MnCO3 (at an initial Mn concentration of 3 mM), demonstrating a two-thirds decrease in remediation time compared to the chitosan-absent system, whereas maximum urease activity increased by ∼50 %. Microstructure analyses indicated that the mineralized precipitates were spherical-shaped MnCO3, and a smaller size and more uniform distribution of MnCO3 is obtained by the regulation of abundant amino and hydroxyl groups in chitosan. These results demonstrate that chitosan accelerates nucleation and tunes the growth of MnCO3 by providing nucleation sites for mineral formation and alleviating the toxicity of metal ions, which has the potential to upgrade MICP process in a sustainable and effective manner. This work provides a reference for further understanding of the biomineralization regulation mechanism, and gives a new perspective into the application of biopolymer-intensified strategies of MICP technology in heavy metal contamination.

Chitosan thermogelation and cascade mineralization via sequential CaCO3 incorporations for wound care

Physically crosslinked hydrogels have shown great potential as excellent and eco-friendly matrices for wound management. Herein, we demonstrate the development of a thermosensitive chitosan hydrogel system using CaCO3 as a gelling agent, followed by CaCO3 mineralization to fine-tune its properties. The chitosan hydrogel effectively gelled at 37 °C and above after an incubation period of at least 2 h, facilitated by the CaCO3-mediated slow deprotonation of primary amine groups on chitosan polymers. Through synthesizing and characterizing various chitosan hydrogel compositions, we found that mineralization played a key role in enhancing the hydrogels' mechanical strength, viscosity, and thermal inertia. Moreover, thorough in vitro and in vivo assessments of the chitosan-based hydrogels, whether modified with mineralization or not, demonstrated their outstanding hemostatic activity (reducing coagulation time by >41 %), biocompatibility with minimal inflammation, and biodegradability. Importantly, in vivo evaluations using a rat burn wound model unveiled a clear wound healing promotion property of the chitosan hydrogels, and the mineralized form outperformed its precursor, with a reduction of >7 days in wound closure time. This study presents the first-time utilization of chitosan/CaCO3 as a thermogelation formulation, offering a promising prototype for a new family of thermosensitive hydrogels highly suited for wound care applications.

Gelatin Methacryloyl (GelMA)-Based Biomaterial Inks: Process Science for 3D/4D Printing and Current Status

Tissue engineering for injured tissue replacement and regeneration has been a subject of investigation over the last 30 years, and there has been considerable interest in using additive manufacturing to achieve these goals. Despite such efforts, many key questions remain unanswered, particularly in the area of biomaterial selection for these applications as well as quantitative understanding of the process science. The strategic utilization of biological macromolecules provides a versatile approach to meet diverse requirements in 3D printing, such as printability, buildability, and biocompatibility. These molecules play a pivotal role in both physical and chemical cross-linking processes throughout the biofabrication, contributing significantly to the overall success of the 3D printing process. Among the several bioprintable materials, gelatin methacryloyl (GelMA) has been widely utilized for diverse tissue engineering applications, with some degree of success. In this context, this review will discuss the key bioengineering approaches to identify the gelation and cross-linking strategies that are appropriate to control the rheology, printability, and buildability of biomaterial inks. This review will focus on the GelMA as the structural (scaffold) biomaterial for different tissues and as a potential carrier vehicle for the transport of living cells as well as their maintenance and viability in the physiological system. Recognizing the importance of printability toward shape fidelity and biophysical properties, a major focus in this review has been to discuss the qualitative and quantitative impact of the key factors, including microrheological, viscoelastic, gelation, shear thinning properties of biomaterial inks, and printing parameters, in particular, reference to 3D extrusion printing of GelMA-based biomaterial inks. Specifically, we emphasize the different possibilities to regulate mechanical, swelling, biodegradation, and cellular functionalities of GelMA-based bio(material) inks, by hybridization techniques, including different synthetic and natural biopolymers, inorganic nanofillers, and microcarriers. At the close, the potential possibility of the integration of experimental data sets and artificial intelligence/machine learning approaches is emphasized to predict the printability, shape fidelity, or biophysical properties of GelMA bio(material) inks for clinically relevant tissues.

Phycocyanin-chitosan complex stabilized emulsion: Preparation, characteristics, digestibility, and stability

Phycocyanin is a natural pigment protein with antioxidant, anti-tumor, and anti-inflammatory properties, but its relatively poor emulsibility limits its use in the food industry. In order to improve the emulsifying capacity of phycocyanin, a novel phycocyanin-chitosan complex was prepared, and the characteristics, digestibility, and stability of emulsion containing oil droplets stabilized by the complex were investigated. The results showed that the phycocyanin-chitosan complex had better stability and lower interfacial tension at pH 6.5 than phycocyanin, and it significantly improved the stability of emulsion and inhibited the aggregation of oil droplets. The phycocyanin-chitosan complex stabilized emulsion showed better physical stability, digestibility, and oxidation stability than the phycocyanin emulsion. The particle size of the phycocyanin-chitosan complex stabilized emulsion was very small (from 0.1 to 2 μm), and its absolute value of zeta potential was high. Overall, this study suggests that the phycocyanin-chitosan complex effectively improved the emulsifying capacity of phycocyanin.

Significantly improve film formability of acetylated xylans by structure optimization and solvent screening

Acetylated xylans have great potential in fabricating functional film and coating materials, which need a good solubility/dispersibility and film formability in an easily evaporable solvent. However, the changes of film formability with degree of substitution by acetyls (DSAc) in different solvent systems for xylans have not been extensively studied, which limit the application of acetylated xylans in film materials. In this study, acetylated xylans with DSAc of 0-2 were prepared and the effects of acetyl groups on solubility/dispersibility, crystallinity and film formability of xylans in water and chloroform solvent systems were investigated. Due to the change of polarity, xylans with DSAc of 0-0.62 are only soluble in water solvents, while xylans with DSAc of 1.13-2 are only soluble in chloroform/ethanol (70/30 v/v) organic solvents. We have found that the film formability of acetylated xylans is highly related to their solubility and crystallization. Film formable xylans all had good solubility in the cast solvents. However, although with good solubility, xylans with DSAc of 0-0.3 and DSAc of 1.76-2 cannot form intact films, which is due to the forming of xylan hydrate crystals and xylan diacetate crystals. With the increase of DSAc, the mechanical property of xylan film increases initially at low DSAc and decreases at high DSAc. This study provides theoretical basis for applying xylans and their derivatives in advanced functional film and coating materials with great biocompatibility and biodegradability.

Chitosan nanoparticles and based composites as a biocompatible vehicle for drug delivery: A review

The shellfish processing industry is one of the largest growing industries across the globe with a market size of around USD 62B. However, it also leads to a significant environmental issue as it produces >80,000 tons of waste shells globally. Unfortunately, the slow degradation of this waste causes it to accumulate over time, posing a serious threat to the marine environment. The key solution to this problem is to recycle this sea waste into a valuable product like chitin which is further used to produce chitosan. Chitosan is a natural biopolymeric substance obtained via N-deacetylation of the chitin. The chitosan-based nanoparticles are further useful for the fabrication of biopolymeric nanocomposites which are used in various biomedical applications specifically in drug delivery. Here, we review the recent advancements in the development of chitosan-based nanocomposites as a biocompatible carrier for drug delivery, specifically focusing on gene delivery, wound healing, microbial treatment, and anticancer drug delivery. By providing a valuable and up-to-date resource, this review illuminates the current state of research concerning chitosan's pivotal role in the biomedical domain as an efficacious drug delivery agent.

From Water for Water: PEDOT:PSS-Chitosan Beads for Sustainable Dyes Adsorption

This study investigates the viability of developing chitosan-based hydrogels derived from waste shrimp shells for the removal of methylene blue and methyl orange, thereby transforming food waste into advanced materials for environmental remediation. Despite chitosan-based adsorbents being conventionally considered ideal for the removal of negative pollutants, through targeted functionalization with poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) at varying concentrations, we successfully enhance the hydrogels' efficacy in also adsorbing positively charged adsorbates. Specifically, the incorporation of PEDOT:PSS at a concentration of 10% v/v emerges as a critical factor in facilitating the robust adsorption of dyes. In the case of the anionic dye methyl orange (MO, 10-5 M), the percentage of removed dye passed from 47% (for beads made of only chitosan) to 66% (for beads made of chitosan-PEDOT:PSS 10%), while, in the case of the cationic dye methylene blue (MB, 10-5 M), the percentage of removed dye passed from 52 to 100%. At the basis of this enhancement, there is an adsorption mechanism resulting from the interplay between electrostatic forces and π-π interactions. Furthermore, the synthesized functionalized hydrogels exhibit remarkable stability and reusability (at least five consecutive cycles) in the case of MB, paving the way for the development of cost-effective and sustainable adsorbents. This study highlights the potential of repurposing waste materials for environmental benefits, introducing an innovative approach to address the challenges regarding water pollution.

Chitosan and Cyclodextrins-Versatile Materials Used to Create Drug Delivery Systems for Gastrointestinal Cancers

Gastrointestinal cancers are characterized by a frequent incidence, a high number of associated deaths, and a tremendous burden on the medical system and patients worldwide. As conventional chemotherapeutic drugs face numerous limitations, researchers started to investigate better alternatives for extending drug efficacy and limiting adverse effects. A remarkably increasing interest has been addressed to chitosan and cyclodextrins, two highly versatile natural carbohydrate materials endowed with unique physicochemical properties. In this respect, numerous studies reported on fabricating various chitosan and cyclodextrin-based formulations that enabled prolonged circulation times, improved cellular internalization of carried drugs, preferential uptake by the targeted cells, reduced side effects, enhanced apoptosis rates, and increased tumor suppression rates. Therefore, this paper aims to briefly present the advantageous properties of these oligo- and polysaccharides for designing drug delivery systems, further focusing the discussion on nanocarrier systems based on chitosan/cyclodextrins for treating different gastrointestinal cancers. Specifically, there are reviewed studies describing promising solutions for colorectal, liver, gastric, pancreatic, and other types of cancers of the digestive system towards creating an updated framework of what concerns anticancer chitosan/cyclodextrin-based drug delivery systems.

pH-Responsive Chitosan-Doped ZnO Hybrid Hydrogels for the Encapsulation of Bioactive Compounds in Aquaculture

In this study, we synthesized and characterized pH-responsive Chitosan-AgCl-doped ZnO hybrid hydrogels and evaluated their potential for loading aquaculture bioactive compounds, and assessed their antimicrobial properties against a threatening pathogen associated with disease across a broad spectrum of warm water fish and invertebrates. Hydrogel characterization consisted of assessing morphology via SEM, composition via EDS, hydrogels' network components interactions via FT-IR and pH response through swelling behavior determinations. The swelling characterization of the synthesized hydrogels demonstrated a pH-responsive behavior, showing that low pH values caused the hydrogel polymeric network to expand and capture more of the aqueous solution. These characteristics make the synthesized hydrogels suitable for the encapsulation and controlled release of drugs and bioactive compounds in aquaculture. Chitosan_ZnO hybrid hydrogels showed great antimicrobial activity against Vibrio harveyi, even better than that of loaded PB hydrogels. Here, we provide evidence for the potential capacity of Chitosan_ZnO hybrid hydrogels for the preventive and curative treatment of diseases that impact aquaculture animal health and prevent drug resistance by bacteria.

Water-borne synthesis of multi-responsive and biodegradable chitosan-crosslinked microgels: Towards self-assembled films with adaptable properties

The present study aims in the synthesis of new biodegradable stimuli-responsive microgels with controllable microstructure and with the ability to form cohesive films. Such self-assembled films by water evaporation at ambient conditions without any chemicals but just physical entanglements between soft colloid shell, present adaptable mechanical, adhesive and mechano-electrical properties. For that, oligo(ethylene glycol)-based stimuli-responsive microgels have been synthesized using biodegradable chitosan-methacrylates (Chi-MAs) with different degree of substitution (DS) as unique cross-linking agents by precipitation polymerization in water, for the first time. In all the cases, the microgels present thermo-responsiveness with hysteresis between heating and cooling cycles. However, this behavior is tuned and controlled using different types and amounts of Chi-MAs. In addition, the type of Chi-MA used can control microgels' microstructure as well as their enzymatic biodegradation. In addition, spontaneous cohesive films formation from colloidal aqueous dispersion with sol-gel transition is demonstrated. The films present tunable mechanical and adhesive properties through microgels' microstructure and enhanced mechano-electrical properties triggered by simple finger pressure (10-15 N). As self-supported films are able to encapsulate different types of active molecules, this study paves the way for suitable self-assembled microgel films for skincare applications as transdermal delivery systems.

Edible Gels with Cranberry Extract: Evaluation of Anthocyanin Release Kinetics

The bioactive compounds found in cranberry fruit are natural antioxidants, and their consumption reduces the risk of diabetes, cardiovascular disease, cancers, and urinary tract infections. Oral gels with cranberry fruit extract are a promising product that can ensure accurate dosage and release of the active compounds and are suitable for people with dysphagia. The aim of this study was to determine the effect of polymeric materials on the dissolution kinetics of cranberry fruit anthocyanins from gel formulations. Gel formulations were prepared using freeze-dried cranberry fruit extract with different gelling excipients: chitosan (G1-G3), sodium carboxymethylcellulose (G4-G6), and sodium carboxymethylcellulose combined with carbomers (G7-G9). The dissolution test showed that the release of anthocyanins from gel formulations G1-G6 and G9 was most intense within the first 10 min, with little change in the anthocyanin content of the acceptor medium afterwards. For the formulations based on carboxymethyl cellulose and carbomers G7 and G8, the amount of anthocyanins released into the acceptor medium gradually increased, which prolonged the release time of the active compounds. The test for the release of anthocyanins from the semi-solid systems through a hydrophilic membrane revealed that within the first hour, the total amount of anthocyanins released from the modeled gel formulations (G1-G9) was within the range of 6.02%-13.50%. The 1% chitosan (G1) gel formulation released the fastest and highest amount of anthocyanins (70% within 6 h). The other formulations showed a slower release of anthocyanins, and after 6 h, the amount of anthocyanins released from formulations G2-G9 was <57%.

Recent advances of magnetic chitosan hydrogel: Preparation, properties and applications

Magnetic chitosan hydrogels are organic-inorganic composite material with the characteristics of both magnetic materials and natural polysaccharides. Due to its biocompatibility, low toxicity and biodegradability, chitosan, a natural polymer has been widely used for preparing magnetic hydrogels. The addition of magnetic nanoparticles to chitosan hydrogels not only improves their mechanical strength, but also endows them with magnetic thermal effects, targeting capabilities, magnetically-sensitive release characteristics, easy separation and recovery, thus enabling them to be used in various applications including drug delivery, magnetic resonance imaging, magnetothermal therapy, and adsorption of heavy metals and dyes. In this review, the physical and chemical crosslinking methods of chitosan hydrogels and the methods for binding magnetic nanoparticles in hydrogel networks are first introduced. Subsequently, the properties of magnetic chitosan hydrogels were summarized including mechanical properties, self-healing, pH responsiveness and properties in magnetic fields. Finally, the potential for further technological and applicative advancements of magnetic chitosan hydrogels is discussed.

The antioxidant activity of polysaccharides: A structure-function relationship overview

Over the last years, polysaccharides have been linked to antioxidant effects using both in vitro chemical and biological models. The reported structures, claimed to act as antioxidants, comprise chitosan, pectic polysaccharides, glucans, mannoproteins, alginates, fucoidans, and many others of all type of biological sources. The structural features linked to the antioxidant action include the polysaccharide charge, molecular weight, and the occurrence of non-carbohydrate substituents. The establishment of structure/function relationships can be, however, biased by secondary phenomena that tailor polysaccharides behavior in antioxidant systems. In this sense, this review confronts some basic concepts of polysaccharides chemistry with the current claim of carbohydrates as antioxidants. It critically discusses how the fine structure and properties of polysaccharides can define polysaccharides as antioxidants. Polysaccharides antioxidant action is highly dependent on their solubility, sugar ring structure, molecular weight, occurrence of positive or negatively charged groups, protein moieties and covalently linked phenolic compounds. However, the occurrence of phenolic compounds and protein as contaminants leads to misleading results in methodologies often used for screening and characterization purposes, as well as in vivo models. Despite falling in the concept of antioxidants, the role of polysaccharides must be well defined according with the matrices where they are involved.

Delivery of Chemotherapy Agents and Nucleic Acids with pH-Dependent Nanoparticles

With less than one percent of systemically injected nanoparticles accumulating in tumors, several novel approaches have been spurred to direct and release the therapy in or near tumors. One such approach depends on the acidic pH of the extracellular matrix and endosomes of the tumor. With an average pH of 6.8, the extracellular tumor matrix provides a gradient for pH-responsive particles to accumulate, enabling greater specificity. Upon uptake by tumor cells, nanoparticles are further exposed to lower pHs, reaching a pH of 5 in late endosomes. Based on these two acidic environments in the tumor, various pH-dependent targeting strategies have been employed to release chemotherapy or the combination of chemotherapy and nucleic acids from macromolecules such as the keratin protein or polymeric nanoparticles. We will review these release strategies, including pH-sensitive linkages between the carrier and hydrophobic chemotherapy agent, the protonation and disruption of polymeric nanoparticles, an amalgam of these first two approaches, and the release of polymers shielding drug-loaded nanoparticles. While several pH-sensitive strategies have demonstrated marked antitumor efficacy in preclinical trials, many studies are early in their development with several obstacles that may limit their clinical use.

Lutein-loaded chitosan/alginate-coated Fe3O4 nanoparticles as effective targeted carriers for breast cancer treatment

Magnetic drug targeting can be a strategy for effectively delivering phytochemicals in cancer treatment. Here, we demonstrate the benefit of magnetic targeting with superparamagnetic iron oxide nanoparticles for cytotoxicity enhancement of lutein (LUT) against breast cancer cells. Fabrication of LUT-loaded chitosan/alginate iron oxide nanoparticles (LUT-CS/Alg-Fe₃O₄-NPs) was optimized by a statistical approach using response surface methodology based on the Box-Behnken design. The optimized LUT-CS/Alg-Fe₃O₄-NPs with a balance among LUT concentration, copolymer coating, and iron ion concentration exhibited controlled size, narrow size distribution, better crystallinity, excellent saturation magnetization, and sustained-release profile. The negligible magnetic coercivity and remanent magnetization confirmed the superparamagnetism of the prepared NPs. The optimized LUT-CS/Alg-Fe₃O₄-NPs were biocompatible while exhibiting a significantly enhanced cytotoxicity towards breast cancer MCF-7 cells upon exposure to a permanent magnet compared to free LUT with a 4-fold increase, suggesting the potential of LUT-CS/Alg-Fe₃O₄-NPs as magnetically targeted delivery for breast cancer.

The Studies on Chitosan for Sustainable Development: A Bibliometric Analysis

Chitosan is a biocompatible polymer with vast applications in pharmacology, medicine, paper making, agriculture, and the food industry due to its low toxicity. Chitosan also plays an important role in the sustainable environment since chitosan is able to absorb greenhouse gases, harmful organic matter, and heavy ions. Therefore, this paper conducts a bibliometric analysis of chitosan for sustainable development using the Scopus database from 1976 to 2023. A performance analysis on the 8002 documents was performed with Harzing's Publish or Perish. Science mapping was conducted using VOSviewer. The annual publication on chitosan for sustainable development showed an upward trend in recent years as the annual publication peaked in 2022 with 1178 documents with most of the documents being articles and published in journals. Material science, chemistry, and engineering are tightly related subject areas. China had the highest publication of 1560 total documents while the United States had the most impactful publication with 55,019 total citations, 68.77 citations per document, 77.6 citations per cited document, h-index 110, and g-index of 211. India had the largest international collaboration with 572 total link strength. "International Journal of Biological Macromolecules", "Carbohydrate Polymers", and "Polymers" have been identified as the top three source titles that publish the most documents on chitosan for sustainable development. The emerging trends in chitosan on sustainable development focus on the application of chitosan as an antibacterial agent and biosorbent for contaminants, especially in water treatment.

Effective Endotoxin Removal from Chitosan That Preserves Chemical Structure and Improves Compatibility with Immune Cells

Chitosan is one of the most researched biopolymers for healthcare applications, however, being a naturally derived polymer, it is susceptible to endotoxin contamination, which elicits pro-inflammatory responses, skewing chitosan's performance and leading to inaccurate conclusions. It is therefore critical that endotoxins are quantified and removed for in vivo use. Here, heat and mild NaOH treatment are investigated as facile endotoxin removal methods from chitosan. Both treatments effectively removed endotoxin to below the FDA limit for medical devices (<0.5 EU/mL). However, in co-culture with peripheral blood mononuclear cells (PBMCs), only NaOH-treated chitosan prevented TNF-α production. While endotoxin removal is the principal task, the preservation of chitosan's structure is vital for the synthesis and lysozyme degradation of chitosan-based hydrogels. The chemical properties of NaOH-treated chitosan (by FTIR-ATR) were significantly similar to its native composition, whereas the heat-treated chitosan evidenced macroscopic chemical and physical changes associated with the Maillard reaction, deeming this treatment unsuitable for further applications. Degradation studies conducted with lysozyme demonstrated that the degradation rates of native and NaOH-treated chitosan-genipin hydrogels were similar. In vitro co-culture studies showed that NaOH hydrogels did not negatively affect the cell viability of monocyte-derived dendritic cells (moDCs), nor induce phenotypical maturation or pro-inflammatory cytokine release.

Remediation plan of nano/microplastic toxicity in food

Microplastic pollution is causing a stir globally due to its persistent and ubiquitous nature. The scientific collaboration is diligently working on improved, effective, sustainable, and cleaner measures to control the nano/microplastic load in the environment especially wrecking the aquatic habitat. This chapter discusses the challenges encountered in nano/microplastic control and improved technologies like density separation, continuous flow centrifugation, oil extraction protocol, electrostatic separation to extract and quantify the same. Although it is still in the early stages of research, biobased control measures, like meal worms and microbes to degrade microplastics in the environment have been proven effective. Besides the control measures, practical alternatives to microplastics can be developed like core-shell powder, mineral powder, and biobased food packaging systems like edible films and coatings developed using various nanotechnological tools. Lastly, the existing and ideal stage of global regulations is compared, and key research areas are pinpointed. This holistic coverage would enable manufacturers and consumers to reconsider their production and purchase decisions for sustainable development goals.

A pH-tuned chitosan-PLGA nanocarrier for fluconazole delivery reduces toxicity and improves efficacy against resistant Candida

Fluconazole (FLZ) is a broad-spectrum antifungal used against Candida infections. Candida auris displays resistance to FLZ. Drug nanocarriers composed of natural (chitosan, C) or synthetic polymers (polylactide co-glycolide, PLGA) show improved drug characteristics, efficacy and reduction in toxicity. Here, C-PLGA nanoparticles (110 nm) were synthesized by coacervation method and loaded with FLZ, achieving ~8-wt% drug loading. The nanoformulation displayed pH-tuned slow sustained drug release (83 %) up to 5 d, at pH 4, while 34 % release occurred at pH 7.0. Fluorescent-tagged C-PLGA-NPs were localized on the Candida cell wall/membrane as seen by confocal microscopy. This resulted in ~1.9-fold reduced efflux of R6G dye as compared to bare drug treatment in Candida albicans and resistant C. auris. The nanoformulation showed a significant 16- and 64-fold (p < 0.0001) enhanced antifungal activity (MIC 5 and 2.5 μg/ml) against C. albicans and C. auris, respectively, as compared to FLZ. The nanoformulation showed highly effective antifungal activity in-vivo against C. albicans and C. auris. Moreover, the nephrotoxicity and hepatotoxicity was negligible. Thus, PLGA NPs-mediated fluconazole delivery can contribute to increased drug efficacy and to reduce the problem of fungal resistance.

Cellulose nanofibrils reinforced chitosan-gelatin based hydrogel loaded with nanoemulsion of oregano essential oil for diabetic wound healing assisted by low level laser therapy

Diabetic foot ulcers are imperfections in the process of wound healing due to hyperglycemic conditions. Here, a nanoemulgel fabricated with oregano essential oil nanoemulsion, assisted by low-level laser therapy, was investigated for its efficacy in diabetic wound healing. A hydrogel- based healing patch, fabricated using biological polymers namely chitosan and gelatin and, polyvinyl pyrollidone. The hydrogel was reinforced with cellulose nanofibrils for enhanced stability and barrier properties. Nanoemulsion of oregano essential oil, with an average particle size of 293.7 ± 8.3 nm, was prepared via homogenization with chitosan as the coating agent. Nanoemulsion impregnated hydrogel, termed as the nanoemulgel, was assessed for its physio-mechanical properties and healing efficiency. The strong linkages in nanoemulgel demonstrated its large swelling capacity, high mechanical strength, and maximum thermal stability. The optimized conditions for low-level laser therapy using 808 nm were 1 W. cm^-2 and 5 min. The optimized drug concentration of 128 μg. mL^-1 exhibited viability of NIH/3 T3 fibroblasts as 75.5 ± 1.2 % after 24 h. Cell migration assay demonstrated that dual therapy facilitated wound healing, with a maximum closure rate of 100 % at 48 h. In vivo results revealed the rapid healing effects of the dual therapy in diabetic rat models with foot ulcers: a maximum healing rate of 97.5 %, minimum scar formation, increased granulation, enhanced reepithelialization, and a drastic decrease in inflammation and neutrophil infiltration within the treatment period compared to monotherapy and control. In summary, the combinatorial therapy of nanoemulgel and low-level laser therapy is a promising regimen for managing diabetic foot ulcers with a rapid healing effect.

Synthesis, optimization, and cell response investigations of natural-based, thermoresponsive, injectable hydrogel: An attitude for 3D hepatocyte encapsulation and cell therapy

For the purpose of developing a 3D vehicle for the delivery of hepatocytes in cell therapy, the improved system of crosslinker and new gelling agent combinations consisting of glycerophosphate and sodium hydrogen carbonate have been employed to produce injectable, thermoresponsive hydrogels based on chitosan and silk fibroin. Adjusting the polymer-to-gelling agent ratio and utilizing a chemical crosslinker developed hydrogel scaffolds with optimal gelling time and pH. Applying sodium hydrogen carbonate neutralizes chitosan while keeping its thermoresponsive characteristics and decreases glycerophosphate from 60% to 30%. Genipin boosts the mechanical properties of hydrogel without affecting the gel time. Due to their stable microstructure and lower amine availability, genipin-containing materials have a low swelling ratio, around six compared to eight for those without genipin. Hydrogels that are crosslinked degrade about half as fast as those that are not. The slowerr degradation of Silk fibroin compared to chitosan makes it an efficient degradation inhibitor in silk-containing formulations. All of the optimized samples showed less than 5% hemolytic activity, indicating that they lacked hemolytic characteristics. The acceptable cell viability in crosslinked hydrogels ranges from 72% to 91% due to the decreasing total salt concentration, which protects cells from hyperosmolality. The pH of hydrogels and their interstitial pores kept most encapsulated cells alive and functioning for 24 h. Urea levels are higher in the encapsulation condition compared to HepG2 cultivated alone, and this may be due to cell-matrix interactions that boost liver-specific activity. Urea synthesis in genipin crosslinked hydrogels increased dramatically from day 1 (about 4 mg dl^-1) to day 3 (approximately 6 mg dl^-1), suggesting the enormous potential of these hydrogels for cell milieu preparation. All mentioned findings represent that the optimized system may be a promising candidate for liver regeneration.

Chitosan Superabsorbent Biopolymers in Sanitary and Hygiene Applications

The consumption of diapers and sanitary products has constantly been rising. Several problems are associated with using chemical-based sanitary products, which are difficult to degrade easily and cause nappy rash and bacterial infections in babies. Therefore, there is an increasing shift towards natural-based sanitary products because of their biodegradability, non-toxicity, and biocompatibility. Several studies are being carried out in which researchers have incorporated natural polymers, such as cellulose, starch, alginate, and xantham gum for producing superabsorbent materials. Chitosan (CS) is one such natural polymer that exhibits anti-microbial activity because of the functional groups present in its structure. Moreover, it is also easily available, biodegradable, and non-toxic. This review mainly focuses on CS’s properties and several approaches to synthesizing natural polymer-based superabsorbent products, such as sanitary pads and diapers. It also briefly discusses the diversified applications of CS as a biopolymer in the cosmetic, medical, food, and textile industries. In addition, this study implies using CS as a superabsorbent biopolymer in the manufacturing and producing sanitary products for women and children. Due to the excellent water retention capacity, swelling ability, and anti-microbial activity exhibited by CS can be considered a potential candidate for producing superabsorbent biopolymers.

Chitin and its derivatives: Functional biopolymers for developing bioproducts for sustainable agriculture-A reality?

Chitinous materials (chitin and its derivatives) are obtained from renewable sources, mainly shellfish waste, having a great potential for the development of bioproducts as alternatives to synthetic agrochemicals. Recent studies have provided evidence that the use of these biopolymers can help control postharvest diseases, increase the content of nutrients available to plants, and elicit positive metabolic changes that lead to higher plant resistance against pathogens. However, agrochemicals are still widely and intensively used in agriculture. This perspective addresses the gap in knowledge and innovation to make bioproducts based on chitinous materials more competitive in the market. It also provides the readers with background to understand why these products are scarcely used and the aspects that need to be considered to increase their use. Finally, information on the development and commercialization of agricultural bioproducts containing chitin or its derivatives in the Chilean market is also provided.

Synthesis of Thermoresponsive PNIPAM-Grafted Cellulose Sulfates for Bioactive Multilayers via Layer-by-Layer Technique

The robust thermoresponsive and bioactive surfaces for tissue engineering by combining poly-N-isopropylacrylamide (PNIPAM) and cellulose sulfate (CS) remain highly in demand but not yet realized. Herein, PNIPAM-grafted cellulose sulfates (PCSs) with diverse degrees of substitution ascribed to sulfate groups (DS_S) are synthesized for the first time. Higher sulfated PCS2 generally forms larger aggregates than lower sulfated PCS1 at their cloud point temperatures (TCP) of around 33 °C, whereas PCS1 leads to larger aggregates at body temperature (37 °C). Via the layer-by-layer (LbL) technique, biocompatible polyelectrolyte multilayers (PEMs) composed of PCSs as polyanions in combination with poly-l-lysine (PLL) or quaternized chitosan (QCHI) as polycations were fabricated. The resulting surfaces contained a more intermingled structure of polyanions with both polycations, while higher sulfated cellulose derivatives (CS2 and PCS2) displayed greater stability. Studies on toxicity and biocompatibility of PEM using 3T3 mouse fibroblasts showed a lower cytotoxicity of PEM with PCS2 and CS2 than PCS1 and CS1. Furthermore, the PEM using PCS2 particularly in combination with QCHI demonstrated excellent biocompatibility that is promising for new bioactive, thermoresponsive coatings on biomaterials and substrata for culturing adhesion-dependent cells.

Bio-Inspired Rhamnolipids, Cyclic Lipopeptides and a Chito-Oligosaccharide Confer Protection against Wheat Powdery Mildew and Inhibit Conidia Germination

Plant protection is mainly based on the application of synthetic pesticides to limit yield losses resulting from diseases. However, the use of more eco-friendly strategies for sustainable plant protection has become a necessity that could contribute to controlling pathogens through a direct antimicrobial effect and/or an induction of plant resistance. Three different families of natural or bioinspired compounds originated from bacterial or fungal strains have been evaluated to protect wheat against powdery mildew, caused by the biotrophic Blumeria graminis f.sp. tritici (Bgt). Thus, three bio-inspired mono-rhamnolipids (smRLs), three cyclic lipopeptides (CLPs, mycosubtilin (M), fengycin (F), surfactin (S)) applied individually and in mixtures (M + F and M + F + S), as well as a chitosan oligosaccharide (COS) BioA187 were tested against Bgt, in planta and in vitro. Only the three smRLs (Rh-Eth-C12, Rh-Est-C12 and Rh-Succ-C12), the two CLP mixtures and the BioA187 led to a partial protection of wheat against Bgt. The higher inhibitor effects on the germination of Bgt spores in vitro were observed from smRLs Rh-Eth-C12 and Rh-Succ-C12, mycosubtilin and the two CLP mixtures. Taking together, these results revealed that such molecules could constitute promising tools for a more eco-friendly agriculture.

Biological and Physico-Chemical Properties of Composite Layers Based on Magnesium-Doped Hydroxyapatite in Chitosan Matrix

In the present study, we report the development and characterization of composite layers (by spin coating) based on magnesium-doped hydroxyapatite in a chitosan matrix, (Ca_10-xMg_x(PO₄)₆(OH)₂; x_Mg = 0, 0.08 and 0.3; HApCh, 8MgHApCh and 30MgHApCh). The MgHApCh composite layers were investigated using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS) techniques. The in vitro biological evaluation included the assessment of their cytotoxicity on MG63 osteoblast-like cells and antifungal activity against Candida albicans ATCC 10231 fungal cell lines. The results of the physico-chemical characterization highlighted the obtaining of uniform and homogeneous composite layers. In addition, the biological assays demonstrated that the increase in the magnesium concentration in the samples enhanced the antifungal effect but also decreased their cytocompatibility. However, for certain optimal magnesium ion concentrations, the composite layers presented both excellent biocompatibility and antifungal properties, suggesting their promising potential for biomedical applications in both implantology and dentistry.

Current Advances in Chitosan Nanoparticles Based Oral Drug Delivery for Colorectal Cancer Treatment

As per the WHO, colorectal cancer (CRC) caused around 935,173 deaths worldwide in 2020 in both sexes and at all ages. The available anticancer therapies including chemotherapy, radiotherapy and anticancer drugs are all associated with limited therapeutic efficacy, adverse effects and low chances. This has urged to emerge several novel therapeutic agents as potential therapies for CRC including synthetic and natural materials. Orally administrable and targeted drug delivery systems are attractive strategies for CRC therapy as they minimize the side effects, enhance the efficacy of anticancer drugs. Nevertheless, oral drug delivery till today faces several challenges like poor drug solubility, stability, and permeability. Various oral nano-based approaches and targeted drug delivery systems have been developed recently, as a result of the ability of nanoparticles to control the release of the encapsulant, drug targeting and reduce the number of dosages administered. The unique physicochemical properties of chitosan polymer assist to overcome oral drug delivery barriers and target the colon tumour cells. Chitosan-based nanocarriers offered additional improvements by enhancing the stability, targeting and bioavailability of several anti-colorectal cancer agents. Modified chitosan derivatives also facilitated CRC targeting through strengthening the protection of encapsulant against acidic and enzyme degradation of gastrointestinal track (GIT). This review aims to provide an overview of CRC pathology, therapy and the barriers against oral drug delivery. It also emphasizes the role of nanotechnology in oral drug targeted delivery system and the growing interest towards chitosan and its derivatives. The present review summarizes the relevant works to date that have studied the potential applications of chitosan-based nanocarrier towards CRC treatment.

A Critical Review of Analytical Applications of Chitosan as a Sustainable Chemical with Functions Galore

Biomass and biowastes stand as sustainable and cost-effective environmentally benign alternative feedstock. Chitosan is a biocompatible, bioactive, and biodegradable biopolymer derived from chitin to achieve eight aspects out of the 12 green chemistry principles. Chitosan got significant attention in several fields including chemical analysis, in addition to chemical functionally, which enabled its use as adsorbent and its structural crosslinking using various crosslinkers. The physicochemical, technological, and optical properties of chitosan have been extensively exploited in analysis. Mainly, deacetylation degree and molecular weight are controlling its properties and hence controlling its functions. This review presents a structure, properties, and functions relationships of chitosan. It also aims to provide an overview of the different functions that chitosan can serve in each analytical technique such as supporting matrix, catalyst…etc. The contribution of chitosan in improving the ecological performance is discussed in each technique.

Rational Design of Self-Emulsifying Pellet Formulation of Thymol: Technology Development Guided by Molecular-Level Structure Characterization and Ex Vivo Testing

The growing need for processing natural lipophilic and often volatile substances such as thymol, a promising candidate for topical treatment of intestinal mucosa, led us to the utilization of solid-state nuclear magnetic resonance (ss-NMR) spectroscopy for the rational design of enteric pellets with a thymol self-emulsifying system (SES). The SES (triacylglycerol, Labrasol®, and propylene glycol) provided a stable o/w emulsion with particle size between 1 and 7 µm. The ex vivo experiment confirmed the SES mucosal permeation and thymol delivery to enterocytes. Pellets W90 (MCC, Neusilin®US2, chitosan) were prepared using distilled water (90 g) by the M1−M3 extrusion/spheronisation methods varying in steps number and/or cumulative time. The pellets (705−740 µm) showed mostly comparable properties—zero friability, low intraparticular porosity (0−0.71%), and relatively high density (1.43−1.45%). They exhibited similar thymol release for 6 h (burst effect in 15th min ca. 60%), but its content increased (30−39.6 mg/g) with a shorter process time. The M3-W90 fluid-bed coated pellets (Eudragit®L) prevented undesirable thymol release in stomach conditions (<10% for 3 h). A detailed, ss-NMR investigation revealed structural differences across samples prepared by M1−M3 methods concerning system stability and internal interactions. The suggested formulation and methodology are promising for other lipophilic volatiles in treating intestinal diseases.

Chitosan-coated nanostructured lipid carriers for transdermal delivery of tetrahydrocurcumin for breast cancer therapy

Chitosan (Ch)-coated nanostructured lipid carriers (NLCs) have great potential for transdermal delivery with high localization of chemotherapeutics in breast cancer. This study used tetrahydrocurcumin (THC), a primary metabolite of curcumin with enhanced antioxidant and anticancer properties, as a model compound to prepare NLCs. Response surface methodology was employed to optimize THC-loaded Ch-coated NLCs (THC-Ch-NLCs) fabricated by high-shear homogenization. The optimized THC-Ch-NLCs had particle size of 244 ± 18 nm, zeta potential of -17.5 ± 0.5 mV, entrapment efficiency of 76.6 ± 0.2% and drug loading of 0.28 ± 0.01%. In vitro release study of THC-Ch-NLCs showed sustained release following the Korsmeyer-Peppas model with Fickian and non-Fickian diffusion at pH 7.4 and 5.5, respectively. THC-Ch-NLCs demonstrated significantly enhanced in vitro skin permeation, cell uptake, and remarkable cytotoxicity toward MD-MBA-231 breast cancer cells compared to the unencapsulated THC, suggesting Ch-NLCs as potential transdermal nanocarriers of THC for triple-negative breast cancer treatment.

Incorporation of Fluorescent Fluorinated Methacrylate Nano-Sized Particles into Chitosan Matrix Formed as a Membranes or Beads

Fluorescent particles are of particular interest as probes and active agents for biomedical, pharmaceutical, and food applications. Here, we present two strategies for incorporation of core-shell acrylic fluorescent nanoparticles (NPs) with Rhodamine B (RhB) as a dye into a chitosan (CS) matrix. We selected two variants of NPsRhB immobilisation in a CS membrane and biopolymeric CS beads. Modification of the method for production of the biopolymer cover/transporter of nanoparticles allowed two series of hydrogels loaded with nanoparticles to be obtained with a similar concentration of the aqueous solution of the nanoparticles. Microscopic analysis showed that the NPs were nonuniformly distributed in millimetre-sized CS beads, as well as membranes, but the fluorescence signal was strong. The composition of CS layers loaded with nanoparticles (CS/NPsRhB) showed water vapour barrier properties, characterised by the contact angle of 71.8°. Finally, we incorporated NPsRhBCS beads into a gelatine matrix to check their stability. The results confirmed good stability of the NPsRhBCS complex system, and no dye leakage was observed from the beads and the membranes. The proposed complex system demonstrated promising potential for further use in bioimaging and, thus, for the development of advanced diagnostic tools.

Development of Turmeric Oil—Loaded Chitosan/Alginate Nanocapsules for Cytotoxicity Enhancement against Breast Cancer

Turmeric oil (TO) exhibits various biological activities with limited therapeutic applications due to its instability, volatility, and poor water solubility. Here, we encapsulated TO in chitosan/alginate nanocapsules (CS/Alg-NCs) using o/w emulsification to enhance its physicochemical characteristics, using poloxamer 407 as a non-ionic surfactant. TO-loaded CS/Alg-NCs (TO-CS/Alg-NCs) were prepared with satisfactory features, encapsulation efficiency, release characteristics, and cytotoxicity against breast cancer cells. The average size of the fabricated TO-CS/Alg-NCs was around 200 nm; their distribution was homogenous, and their shapes were spherical, with smooth surfaces. The TO-CS/Alg-NCs showed a high encapsulation efficiency, of 70%, with a sustained release of TO at approximately 50% after 12 h at pH 7.4 and 5.5. The TO-CS/Alg-NCs demonstrated enhanced cytotoxicity against two breast cancer cells, MDA-MB-231 and MCF-7, compared to the unencapsulated TO, suggesting that CS/Alg-NCs are potential nanocarriers for TO and can serve as prospective candidates for in vivo anticancer activity evaluation.

Chitosan: A review of molecular structure, bioactivities and interactions with the human body and micro-organisms

Chitosan has many desirable attributes e.g. antimicrobial properties and promoting wound healing, and is used in various applications. This article first discusses how degree of deacetylation (DD) and molecular weight (MW) impacts on what level of bioactivities chitosan manifests, then introduces the "molecular chain configuration" model to explain various possible mechanisms of antimicrobial interactions between chitosan with different MW and different types of bacteria. Similarly, the possible pathways of how chitosan reacts with cancer and the body's immune system to demonstrate immune and antitumor effects are also discussed by using this model. Moreover, the possible mechanisms of how chitosan enhances coagulation and wound healing are also discussed. With these beneficial bioactivities in mind, the application of chitosan in surgery, tissue engineering and oncology is outlined. This review concludes that as chitosan demonstrates many beneficial bioactivities via multiple mechanisms, it is an important polymer with a promising future in medicine.

Interactions between Nanoparticles and Intestine

The use of nanoparticles (NPs) has surely grown in recent years due to their versatility, with a spectrum of applications that range from nanomedicine to the food industry. Recent research focuses on the development of NPs for the oral administration route rather than the intravenous one, placing the interactions between NPs and the intestine at the centre of the attention. This allows the NPs functionalization to exploit the different characteristics of the digestive tract, such as the different pH, the intestinal mucus layer, or the intestinal absorption capacity. On the other hand, these same characteristics can represent a problem for their complexity, also considering the potential interactions with the food matrix or the microbiota. This review intends to give a comprehensive look into three main branches of NPs delivery through the oral route: the functionalization of NPs drug carriers for systemic targets, with the case of insulin carriers as an example; NPs for the delivery of drugs locally active in the intestine, for the treatment of inflammatory bowel diseases and colon cancer; finally, the potential concerns and side effects of the accidental and uncontrolled exposure to NPs employed as food additives, with focus on E171 (titanium dioxide) and E174 (silver NPs).

Thermo-rheological properties of chitosan hydrogels with hydroxypropyl methylcellulose and methylcellulose

Thermal and rheological properties of methylcellulose (MC) and hydroxypropyl methylcellulose (HPMC) hydrogels with chitosan (CHI) were investigated to verify the potential application of these blends as structured systems for oil transport (emulgel, oleogels, and bigels). FTIR confirmed hydrophobic interactions of cellulosic polymers with chitosan. In the temperature sweep, the thermosensitive hydrogels showed their reduced gel point compared to the original polymers. The gelation temperature was reduced from 66.9 °C for pure HPMC to 43.6 °C and 43.6 °C (MC pure polymer) to 39.3 °C when 30% CHI was added for both cases. The addition of 20 and 30% chitosan is enough to modify the extension of the gelation temperature of these polymers. These results indicate that the addition of chitosan enables MC and HPMC to form gels at lower temperatures, which could allow milder thermal conditions to be applied in processing oil carrier systems.

Influence of Temperature and Polymer Concentration on the Nonlinear Response of Highly Acetylated Chitosan-Genipin Hydrogels

Strain hardening, i.e., the nonlinear elastic response of materials under load, is a physiological response of biological tissues to mechanical stimulation. It has recently been shown to play a central role in regulating cell fate. In this paper, we investigate the effect of temperature and polymer concentrations on the strain hardening of covalent hydrogels composed of pH-neutral soluble chitosans crosslinked with genipin. A series of highly acetylated chitosans with a fraction of acetylated units, FA, in the range of 0.4-0.6 was synthesized by the homogeneous re-N-acetylation of a partially acetylated chitosan or the heterogeneous deacetylation of chitin. A chitosan sample with an FA = 0.44 was used to prepare hydrogels with genipin as a crosslinker at a neutral pH. Time and frequency sweep experiments were then performed to obtain information on the gelling kinetics and mechanical response of the resulting hydrogels under small amplitude oscillatory shear. While the shear modulus depends on the chitosan concentration and is almost independent of the gel temperature, we show that the extent of hardening can be modulated when the gelling temperature is varied and is almost independent of the experimental conditions used to build the hydrogels (ex situ or in situ gelation). The overall effect is attributed to a subtle balance between the physical (weak) entanglements and covalent (strong) crosslinks that determine the mechanical response of highly acetylated chitosan hydrogels at large deformations.

Polysaccharides as wall materials in spray-dried microencapsulation of bioactive compounds: Physicochemical properties and characterization

Natural bioactive compounds (BCs) are types of chemicals found in plants and certain foods that promote good health, however they are sensitive to processing and environmental conditions. Microencapsulation by spray drying is a widely used and cost-effective approach to create a coating layer to surround and protect BCs and control their release, enabling the production of high functional products/ingredients with extended shelf life. In this process, wall materials determine protection efficiency, and physical properties, bioavailability, and storage stability of microencapsulated products. Therefore, an understanding of physicochemical properties of wall materials is essential for the successful and effective spray-dried microencapsulation process. Typically, polysaccharide-based wall materials are generated from more sustainable sources and have a wider range of physicochemical properties and applications compared to their protein-based counterparts. In this review, we highlight the essential physicochemical properties of polysaccharide-based wall materials for spray-dried microencapsulation of BCs including solubility, thermal stability, and emulsifying properties, rheological and film forming properties. We provide further insight into possibilities for the chemical structure modification of native wall materials and their controlled release behaviors. Finally, we summarize the most recent studies involving polysaccharide biopolymers as wall materials and/or emulsifiers in spray-dried microencapsulation of BCs.

Effects of chitosan and Tween 80 addition on the properties of nanofiber mat through the electrospinning

Chitosan (CS) with excellent biomedical properties was mixed with polyvinyl alcohol (PVA) to be used as the spinning solution. The spinning solutions with various concentrations of CS:PVA from 10:90% to 50:50% (v/v) were investigated. Tween 80 (T80) was added in the spinning solutions of CS and PVA. The nanofiber mats with and without T80 addition obtained from the spinning solutions by electrospinning technique were investigated and addressed. The results showed that the viscosity of the CS and PVA spinning solutions increased with increasing the CS concentration, whereas the viscosity decreased after T80 addition. The nanofiber mats with 10–30% CS concentrations were prepared successfully as a smooth surface and high dense nanofiber mat. The average diameter of the nanofiber decreased with increasing the CS concentration. The increase in the CS concentration of the nanofiber mat can increase the mechanical and antibacterial properties, whereas the wettability and drug release property were decreased. Moreover, the nanofiber mats with T80 addition had higher mechanical property and wettability than the nanofiber mats without T80 addition. Finally, the T80 addition can enhance hydrophilicity and promote the drug release property of the nanofiber mat.

Rapid Removal of Acid Red 88 by Zeolite/Chitosan Hydrogel in Aqueous Solution

In the present study, we developed a new adsorbent product with zeolite crosslinked chitosan (ZL–CH hydrogel) to remove acid red 88 (AR88) in an aqueous solution. The effects of several factors, such as the comparison of ZL–CH hydrogel and the absence of chitosan, pH, adsorbent dosage, initial AR88 concentration, contact time, and ion strength, were determined. Obtained results showed that ZL–CH hydrogel improved AR88 removal compared to the absence of chitosan, with an adsorption capacity of 332.48 mg/g in equilibrium time of 1 min, and adding ionic strength had no significant effect. However, with optimal conditions at pH 2.0, dry ZL–CH became hydrogel due to protonation of amino and hydroxyl groups through hydrogen bonds in the AR88 solution. Volume fraction and interaction force decreased with increasing porosity, leading to an increase in adsorption capacity and swelling ratio. Experimental data of the adsorption process showed the Freundlich isotherm model. The equilibrium for adsorption and swelling kinetics studies showed and fitted a pseudo-second-order model. NaOH was successful as a desorbing agent with 93.8%, and it followed the pseudo-second-order kinetics model. The recycling process indicates great potential for AR88 removal.

Recent Advancements in Smart Biogenic Packaging: Reshaping the Future of the Food Packaging Industry

Due to their complete non-biodegradability, current food packages have resulted in major environmental issues. Today’s smart consumer is looking for alternatives that are environmentally friendly, durable, recyclable, and naturally rather than synthetically derived. It is a well-established fact that complete replacement with environmentally friendly packaging materials is unattainable, and bio-based plastics should be the future of the food packaging industry. Natural biopolymers and nanotechnological interventions allow the creation of new, high-performance, light-weight, and environmentally friendly composite materials, which can replace non-biodegradable plastic packaging materials. This review summarizes the recent advancements in smart biogenic packaging, focusing on the shift from conventional to natural packaging, properties of various biogenic packaging materials, and the amalgamation of technologies, such as nanotechnology and encapsulation; to develop active and intelligent biogenic systems, such as the use of biosensors in food packaging. Lastly, challenges and opportunities in biogenic packaging are described, for their application in sustainable food packing systems.

pH-Induced 3D Printable Chitosan Hydrogels for Soft Actuation

Three-dimensional (3D) printing represents a suitable technology for the development of biomimetic scaffolds for biomedical and tissue engineering applications. However, hydrogel-based inks’ printability remains a challenge due to their restricted print accuracy, mechanical properties, swelling or even cytotoxicity. Chitosan is a natural-derived polysaccharide that has arisen as a promising bioink due to its biodegradability, biocompatibility, sustainability and antibacterial properties, among others, as well as its ability to form hydrogels under the influence of a wide variety of mechanisms (thermal, ionic, pH, covalent, etc.). Its poor solubility at physiological pH, which has traditionally restricted its use, represents, on the contrary, the simplest way to induce chitosan gelation. Accordingly, herein a NaOH strong base was employed as gelling media for the direct 3D printing of chitosan structures. The obtained hydrogels were characterized in terms of morphology, chemical interactions, swelling and mechanical and rheological properties in order to evaluate the influence of the gelling solution’s ionic strength on the hydrogel characteristics. Further, the influence of printing parameters, such as extrusion speed (300, 600 and 800 mm/min) and pressure (20–35 kPa) and the cytocompatibility were also analyzed. In addition, printed gels show an electro-induced motion due to their polycationic nature, which highlights their potential as soft actuators and active scaffolds.