FeF3/(Acetylene Black and Multi-Walled Carbon Nanotube) Composite for Cathode Active Material of Thermal Battery through Formation of Conductive Network Channels

Considerable research is being conducted on the use of FeF3 as a cathode replacement for FeS2 in thermal batteries. However, FeF3 alone is inefficient as a cathode active material because of its low electrical conductivity due to its wide bandgap (5.96 eV). Herein, acetylene black and multi-walled carbon nanotubes (MWCNTs) were combined with FeF3, and the ratio was optimized. When acetylene black and MWCNTs were added separately to FeF3, the electrical conductivity increased, but the mechanical strength decreased. When acetylene black and MWCNTs were both added to FeF3, the FeF3/M1AB4 sample (with 1 wt.% MWCNTs and 4% AB) afforded a discharge capacity of approximately 74% of the theoretical capacity (712 mAh/g) of FeF3. Considering the electrical conductivity and mechanical strength, this composition was confirmed to be the most suitable.

Identification of a Gene Signature Predicting (Nano)Particle-Induced Adverse Lung Outcome in Rats

Nanoparticles are extensively used in industrial products or as food additives. However, despite their contribution to improving our quality of life, concerns have been raised regarding their potential impact on occupational and public health. To speed up research assessing nanoparticle-related hazards, this study was undertaken to identify early markers of harmful effects on the lungs. Female Sprague Dawley rats were either exposed to crystalline silica DQ-12 with instillation, or to titanium dioxide P25, carbon black Printex-90, or multi-walled carbon nanotube Mitsui-7 with nose-only inhalation. Tissues were collected at three post-exposure time points to assess short- and long-term effects. All particles induced lung inflammation. Histopathological and biochemical analyses revealed phospholipid accumulation, lipoproteinosis, and interstitial thickening with collagen deposition after exposure to DQ-12. Exposure to the highest dose of Printex-90 and Mitsui-7, but not P25, induced some phospholipid accumulation. Comparable histopathological changes were observed following exposure to P25, Printex-90, and Mitsui-7. Comparison of overall gene expression profiles identified 15 potential early markers of adverse lung outcomes induced by spherical particles. With Mitsui-7, a distinct gene expression signature was observed, suggesting that carbon nanotubes trigger different toxicity mechanisms to spherical particles.

Fe-Ni/MWCNTs Nano-Composites for Hexavalent Chromium Reduction in Aqueous Environment

A novel Cr (VI) removal material was designed and produced comprising multi-walled carbon nanotubes (MWCNTs) as a support with a high specific surface area and the loaded Fe-Ni bimetallic particles as catalytic reducing agents. Such a design permits the composite particle to perform the adsorption, reduction, and immobilisation of Cr (VI) quickly and efficiently. Due to MWCNTs' physical adsorption, Cr (VI) in solution aggregates in the vicinity of the composite, and Fe rapidly reduces Cr (VI) to Cr (III) catalysed by Ni. The results demonstrated that the Fe-Ni/MWCNTs exhibits an adsorption capacity of 207 mg/g at pH = 6.4 for Cr (VI) and 256 mg/g at pH 4.8, which is about twice those reported for other materials under similar conditions. The formed Cr (III) is solidified to the surface by MWCNTs and remains stable for several months without secondary contamination. The reusability of the composites was proven by retaining at least 90% of the adsorption capacity for five instances of reutilization. Considering the facile synthesis process, low cost of raw material, and reusability of the formed Fe-Ni/MWCNTs, this work shows great potential for industrialisation.

Synthesis and Characterization of a Multi-Walled Carbon Nanotube-Ionic Liquid/Polyaniline Adsorbent for a Solvent-Free In-Needle Microextraction Method

Sample preparation is an essential process when handling complex matrices. Extraction without using a solvent requires the direct transfer of analytes from the sample to the adsorbent either in the gas or liquid phase. In this study, a wire coated with a new adsorbent was fabricated for in-needle microextraction (INME) as a solvent-free sample extraction method. The wire inserted into the needle was placed in the headspace (HS), which was saturated with volatile organic compounds from the sample in a vial. A new adsorbent was synthesized via electrochemical polymerization by mixing aniline with multi-walled carbon nanotubes (MWCNTs) in the presence of an ionic liquid (IL). The newly synthesized adsorbent using IL is expected to achieve high thermal stability, good solvation properties, and high extraction efficiency. The characteristics of the electrochemically synthesized surfaces coated with MWCNT-IL/polyaniline (PANI) adsorbents were characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and atomic force microscopy (AFM). Then, the proposed HS-INME-MWCNT-IL/PANI method was optimized and validated. Accuracy and precision were evaluated by analyzing replicates of a real sample containing phthalates, showing spike recovery between 61.13% and 108.21% and relative standard deviations lower than 15%. The limit of detection and limit of quantification of the proposed method were computed using the IUPAC definition as 15.84~50.56 μg and 52.79~168.5 μg, respectively. We concluded that HS-INME using a wire coated with the MWCNT-IL/PANI adsorbent could be repeatedly used up to 150 times without degrading its extraction performance in an aqueous solution; it constitutes an eco-friendly and cost-effective extraction method.

Correlation Analysis between Strength and Defect of Nano-Cementitious Composites using Ultrasonic Pulse Velocity

Recently, researchers are conducting studies to improve the mechanical and chemical properties of cementitious composites mixed with nanomaterials. Defects may occur inside nano-cementitious composites due to nanomaterial agglomeration in the manufacturing process. These defects can degrade the mechanical performance of the nano-cementitious composite. This study performs ultrasonic non-destructive and compressive strength tests according to the size of defects in nano-cementitious composites. Multi-walled carbon nanotubes (MWCNTs) were used for the nanomaterial, and internal defects of various sizes were considered in the center of the specimens. Ultrasonic pulse velocity was measured according to the defect size until 30 curing days, after which the compressive strength was measured. The ultrasonic pulse velocity of the nano-cementitious composites decreased by up to 9.6% in relation to that of the specimens without defects as the defect size increased, and the compressive strength decreased by up to 35.7%. This study's findings revealed a correlation between ultrasonic pulse velocity and compressive strength according to defect size. Future ultrasonic non-destructive tests will allow for the prediction of mechanical performance and the detection of defects within nano-cementitious composites.

Synergistic Function between Phosphorus-Containing Flame Retardant and Multi-Walled Carbon Nanotubes towards Fire Safe Polystyrene Composites with Enhanced Electromagnetic Interference Shielding

As a universal polymer material, polystyrene (PS) is widely applied in electrical devices and construction. Thus, it is necessary to improve the flame retardancy and electromagnetic shielding properties of PS material. In this work, PS/silicon-wrapped ammonium polyphosphate/Inorganic acid-treated multi-walled carbon nanotubes composites (PS/SiAPP/aMWCNT, abbreviated as PAC) were prepared via methods of filtration-induced assembly and hot-pressing. Morphology and structure characterization demonstrated that SiAPP and aMWCNT had good dispersion in PS and excellent compatibility with the PS matrix. Thermogravimetric analysis revealed that the addition of aMWCNT to PS improved its thermal stability and carbon-forming characteristics. The peak heat release rate, the peak carbon monoxide production rate, and the peak smoke production rate of the PAC10 composite decreased by 53.7%, 41.9%, and 45.5%, respectively, while its electromagnetic shielding effectiveness reached 12 dB. These enhancements were attributed to the reason that SiAPP and aMWCNT synergistically catalyzed the char generation and SiAPP produced free radical scavengers and numbers of incombustible gases, which could decrease the oxygen concentration and retard the combustion reaction. Therefore, the assembled PS/SiAPP/aMWCNT system provides a new pathway to improve the flame retardant and electromagnetic shielding properties of PS.

Multiwalled Carbon Nanotubes Alter the PSII Photochemistry, Photosystem-Related Gene Expressions, and Chloroplastic Antioxidant System in Zea mays under Copper Toxicity

A critical approach against copper (Cu) toxicity is the use of carbon nanomaterials (CNMs). However, the effect of CNMs on Cu toxicity-exposed chloroplasts is not clear. The photosynthetic, genetic, and biochemical effects of multiwalled carbon nanotubes (50-100-250 mg L^-1 CNT) were investigated under Cu stress (50-100 μM CuSO₄) in Zea mays chloroplasts. F_v/F_m and F_v/F_o were suppressed under stress. Stress altered the antioxidant system and the expression of psaA, psaB, psbA, and psbD. The chloroplastic activities of superoxide dismutase (SOD), ascorbate peroxidase (APX), glutathione S-transferase (GST), and glutathione peroxidase (GPX) increased under CNT + stress, and those of hydrogen peroxide (H₂O₂) and lipid peroxidation decreased. CNTs were promoted to the maintenance of the redox state by regulating enzyme/non-enzyme activity/contents involved in the AsA-GSH cycle. Furthermore, CNTs inverted the negative effects of Cu by upregulating the transcriptions of photosystem-related genes. However, the high CNT concentration had adverse effects on the antioxidant capacity. CNT has great potential to confer tolerance by reducing Cu-induced damage and protecting the biochemical reactions of photosynthesis.

Effective Practical Solutions for De-Icing of Automotive Component

Carbon Nanotube (CNTs)-based masterbatches have been mixed with thermoplastic polymers currently used to manufacture automotive components. These mixtures have been tailored to integrate an effective heating function in the materials. The manufacturing method for composite compounding and processing conditions significantly affects the electrical resistivity of the developed materials. The resistivity of the material can be controlled within tight tolerances sufficient to meet automotive requirements. The optimal compounding parameters of the melt process technologies were defined to obtain uniform filler dispersion and distribution. Heating and de-icing tests were performed on sheet specimens with optimized CNT content and electrical conductivity suitable for effective electro-thermal behaviour with low input voltages (≤24 V DC), making them safe for users. Finally, a simplified analytical model of the Joule effect arising from an energy balance of the system under study (heat equation) was developed and validated by comparison with experimental data for use in future development for the purpose of the preliminary design of components in the automotive sector.

NIR Light-Triggered Chemo-Phototherapy by ICG Functionalized MWNTs for Synergistic Tumor-Targeted Delivery

The combinational application of photothermal therapy (PTT), chemotherapy, and nanotechnology is a booming therapeutic strategy for cancer treatment. Multi-walled carbon nanotube (MWNT) is often utilized as drug carrier in biomedical fields with excellent photothermal properties, and indocyanine green (ICG) is a near-infrared (NIR) dye approved by FDA. In addition, ICG is also a photothermal agent that can strongly absorb light energy for tumor ablation. Herein, we explored a synergistic strategy by connecting MWNT and a kind of ICG derivate ICG-NH₂ through hyaluronic acid (HA) that possesses CD44 receptor targeting ability, which largely enhanced the PTT effect of both MWNT and ICG-NH₂. To realize the synergistic therapeutic effect of chemotherapy and phototherapy, doxorubicin (DOX) was attached on the wall of MWNT via π-π interaction to obtain the final MWNT-HA-ICG/DOX nanocomplexes. Both in vitro and in vivo experiments verified the great therapeutic efficacy of MWNT-HA-ICG/DOX nanocomplexes, which was characterized by improved photothermal performance, strengthened cytotoxicity, and elevated tumor growth inhibition based on MCF-7 tumor models. Therefore, this synergistic strategy we report here might offer a new idea with promising application prospect for cancer treatment.

Ultrafiltration of α-Lactalbumin Protein: Acquaintance of the Filtration Performance by Membrane Structure and Surface Alteration

α-Lactalbumin is an essential protein with multiple roles in physiological and the nutritional functionalities, such as diabetic prevention, blood pressure stabilization, and cancer cell inhibition. In the present work, polyethersulfone (PES)-based membranes were developed by incorporating Pluronic F127 and carbon nanotubes with single- and multi-walled dimensions (Sw-Cnts and Mw-Cnts) as additives. The resulting membranes were evaluated for use in the filtration of α-lactalbumin protein solution. Four series of membranes, including PES pristine membrane, were fabricated via the phase inversion process. The characteristics of the membrane samples were analyzed in terms of morphology, membrane surface hydrophilicity and roughness, and surface chemistry. The characterization results show that the incorporation of additive increased the surface wettability by reducing the surface water contact angle from 80.4° to 64.1° by adding F127 and Mw-Cnt additives. The highest pure water permeability of 135 L/(m2·h·bar) was also exhibited by the PES/F127/Mw-Cnt membrane. The performance of the modified membranes was clearly better than the pristine PSF for α-lactalbumin solution filtration. The permeability of α-lactalbumin solution increased from 9.0 L/(m2·h·bar) for the pristine PES membrane to 10.5, 11.0 and 11.5 L/(m2·h·bar) for membranes loaded with Pluronic F127, Sw-Cnts, and Mw-Cnts, respectively. Those increments corresponded to 17, 22, and 28%. Such increments could be achieved without altering the α-lactalbumin rejections of 80%. Remarkably, the rejection for the membrane loaded with Sw-Cnts even increased to 89%.

Dietary Docosahexaenoic Acid as a Potential Treatment for Semi-acute and Chronic Particle-Induced Pulmonary Inflammation in Balb/c Mice

Acute and chronic inflammation are vital contributing factors to pulmonary diseases which can be triggered by exposure to occupational and man-made particles; however, there are no established treatments. One potential treatment shown to have anti-inflammatory capabilities is the dietary supplement docosahexaenoic acid (DHA), an omega-3 polyunsaturated fatty acid found in fish oil. DHA's anti-inflammatory mechanisms are unclear for particle-induced inflammation; therefore, this study evaluated DHA as a prophylactic treatment for semi-acute and chronic particle-induced inflammation in vivo. Balb/c mice were fed a control or 1% DHA diet and exposed to dispersion media, an inflammatory multi-walled carbon nanotube (MWCNT), or crystalline silica (SiO₂) either once (semi-acute) or once a week for 4 weeks (chronic). The hypothesis was that DHA will decrease pulmonary inflammatory markers in response to particle-induced inflammation. Results indicated that DHA had a trending anti-inflammatory effect in mice exposed to MWCNT. There was a general decrease in inflammatory signals within the lung lavage fluid and upregulation of M2c macrophage gene expression in the spleen tissue. In contrast, mice exposed to SiO₂ while on the DHA diet significantly increased most inflammatory markers. However, DHA stabilized the phagolysosomal membrane upon prolonged treatment. This indicated that DHA treatment may depend upon certain inflammatory particle exposures as well as the length of the exposure.

Human Motion State Recognition Based on Flexible, Wearable Capacitive Pressure Sensors

Human motion state recognition technology based on flexible, wearable sensor devices has been widely applied in the fields of human–computer interaction and health monitoring. In this study, a new type of flexible capacitive pressure sensor is designed and applied to the recognition of human motion state. The electrode layers use multi-walled carbon nanotubes (MWCNTs) as conductive materials, and polydimethylsiloxane (PDMS) with microstructures is embedded in the surface as a flexible substrate. A composite film of barium titanate (BaTiO₃) with a high dielectric constant and low dielectric loss and PDMS is used as the intermediate dielectric layer. The sensor has the advantages of high sensitivity (2.39 kPa⁻¹), wide pressure range (0–120 kPa), low pressure resolution (6.8 Pa), fast response time (16 ms), fast recovery time (8 ms), lower hysteresis, and stability. The human body motion state recognition system is designed based on a multi-layer back propagation neural network, which can collect, process, and recognize the sensor signals of different motion states (sitting, standing, walking, and running). The results indicate that the overall recognition rate of the system for the human motion state reaches 94%. This proves the feasibility of the human motion state recognition system based on the flexible wearable sensor. Furthermore, the system has high application potential in the field of wearable motion detection.

Magnetite nanoparticles decorated on multi-walled carbon nanotubes for removal of Cu2+ from aqueous solution

Acid-functionalized multi-walled carbon nanotube (MWCNTs-COOH) was prepared by acid treatment followed by decoration with magnetite (Fe₃O₄) nanoparticles (Fe₃O₄/MWCNTs-COOH) by co-precipitation of Fe²⁺/Fe³⁺ in the colloidal suspension of MWCNTs-COOH. The adsorption capacity and separation efficiency of these two adsorbents were investigated for the removal of Cu²⁺ ions in aqueous solution as water treatment adsorbents. The effect of reaction conditions, such as contact time, initial concentration of Cu²⁺ ions, and adsorbent dosage, on the adsorption capacity of MWCNTs-COOH was investigated. It was found that contact time of 10 min, adsorbent dosage of 0.2 g/L and 15 mg/L as initial concentration of Cu²⁺ ions are ideal conditions for maximum adsorption capacity (10.45 mg/g). The adsorption capacity of synthesized Fe₃O₄/MWCNTs-COOH containing different weight percent of Fe₃O₄ (10, 25, 50 wt%) was explored for removal of Cu²⁺ ions from aqueous solution and the best results achieved with 25 wt% Fe₃O₄/MWCNTs-COOH, which exhibited optimum adsorption capacity of 9.50 mg/g and 97% separation efficiency. Further, Langmuir and Freundlich isotherm models were applied to validate experimental data obtained in this work for Cu²⁺ adsorption.

Statistical Analysis of Polymer Nanocomposites for Mechanical Properties

Epoxy resins, due to their high stiffness, ease of processing, good heat, and chemical resistance obtained from cross-linked structures, have found applications in electronics, adhesives coatings, industrial tooling, and aeronautic and automotive industries. These resins are inherently brittle, which has limited their further application. The emphasis of this study is to improve the properties of the epoxy resin with a low-concentration (up to 0.4% by weight) addition of Multi-Walled Carbon Nanotubes (MWCNTs). Mechanical characterization of the modified composites was conducted to study the effect of MWCNTs infusion in the epoxy resin. Nanocomposites samples showed significantly higher tensile strength and fracture toughness compared to pure epoxy samples. The morphological studies of the modified composites were studied using Scanning Electron Microscopy (SEM).

New Multi-Walled carbon nanotube of industrial interest induce cell death in murine fibroblast cells

The search for new nanomaterials has brought to the multifactorial industry several opportunities for use and applications for existing materials. Carbon nanotubes (CNT), for example, present excellent properties which allow us to assume a series of applications, however there is concern in the industrial scope about possible adverse health effects related to constant exposure for inhalation or direct skin contact. Thus, using cell models is the fastest and safest way to assess the effects of a new material. The aim of this study was to investigate the cytotoxic profile in LA9 murine fibroblast lineage, of a new multi-walled carbon nanotube (MWCNT) that was functionalized with tetraethylenepentamine (TEPA) to obtain better physical-chemical characteristics for industrial use. The modifications presented in the CNT cause concern, as they can change its initial characteristics, making this nanomaterial harmful. HR-TEM, FE-SEM and zeta potential were used for the characterization. Cytotoxicity and cell proliferation tests, oxidative and nitrosative stress analyzes and inflammatory cytokine assay (TNF-α) were performed. The main findings demonstrated a reduction in cell viability, increased release of intracellular ROS, accompanied by an increase in TNF-α, indicating an important inflammatory profile. Confirmation of the data was performed by flow cytometry and ImageXpress with apoptosis/necrosis markers. These data provide initial evidence that OCNT-TEPA has a cytotoxic profile dependent on the concentration of LA9 fibroblasts, since there was an increase in free radicals, inflammation induction and cell death, suggesting that continuous exposure to this nanoparticle can cause damage to different tissues in the organism.

Dry sonication process for preparation of hybrid structures based on graphene and carbon nanotubes usable for chemical sensors

The combination of graphene (G) and multi-walled carbon nanotubes (MWCNTs) creates three-dimensional hybrid structures particularly suitable as next-generation electrical interface materials. Nevertheless, efficient mixing of the nanopowders is challenging, unless previous disaggregation and eventual surface modification of both is reached. To avoid use of solvents and multistep purification process for synthesis of stable G/MWCNTs hybrids, herein, a novel dry method based on an air sonication process was used. Taking advantage from the vigorous turbulent currents generated by powerful ultrasonication in air that induces strong thermal convection or radiation to and from the particles, it simultaneously ensures disentanglement of the large MWCNT bundles and G exfoliation and their only mild surface modifications. By changing the ratio between MWCNTs and G, a range of hybrids was obtained, different in surface morphology and chemistry. These hybrids have shown great potential as sensing material for designing mass-based sensors for toxic gases and chemiresistor for vapors detection.

Performance Comparison of Solid Lead Ion Electrodes with Different Carbon-Based Nanomaterials as Electron-Ion Exchangers

Carbon-based nanomaterials with carboxylation or chemical modification are widely used as electron-ion exchangers of solid electrodes. For reducing the complexity and dangerousness of the intermediate layer preparation, different original carbon-based nanomaterials are dispersed in deionized water. They are applied in the fabrication of Pb2+-selective electrodes. Because the contact angle of graphene reached 132.5°, the Pb2+-selective electrode of graphene used as an electron-ion exchanger showed excellent performance with a low detection limit of 3.4 × 10-8 M and a fast average response time of 42.6 s. The Nernstian response slope could reach 26.8 mV/decade, and the lifetime lasted for a month. Therefore, graphene suspension without any treatment can be used as the intermediate layer of solid-state electrodes, providing a reference for the preparation of other ion-selective electrodes.

Preparation and Electrical Properties of Silicone Composite Films Based on Silver Nanoparticle Decorated Multi-Walled Carbon Nanotubes

The electrical properties of silicone composite films filled with silver (Ag) nanoparticle-decorated multi-walled carbon nanotubes (MWNT) prepared by solution processing are investigated. Pristine MWNT is oxidized and converted to the acyl chloride-functionalized MWNT using thionyl chloride, which is subsequently reacted with amine-terminated poly(dimethylsiloxane) (APDMS). Thereafter, APDMS-modified MWNT are decorated with Ag nanoparticles and then reacted with a poly(dimethylsiloxane) solution to form Ag-decorated MWNT silicone (Ag-decorated MWNT-APDMS/Silicone) composite. The morphological differences of the silicone composites containing Ag-decorated MWNT and APDMS-modified MWNT are observed by transmission electron microscopy (TEM) and the surface conductivities are measured by the four-probe method. Ag-decorated MWNT-APDMS/Silicone composite films show higher surface electrical conductivity than MWNT/silicone composite films. This shows that the electrical properties of Ag-decorated MWNT-APDMS/silicone composite films can be improved by the surface modification of MWNT with APDMS and Ag nanoparticles, thereby expanding their applications.

Docosahexaenoic acid impacts macrophage phenotype subsets and phagolysosomal membrane permeability with particle exposure

Inhalation of particles results in pulmonary inflammation; however, treatments are currently lacking. Docosahexaenoic acid (DHA) is an omega-3 polyunsaturated fatty acid shown to exhibit anti-inflammatory capabilities. The impact of DHA on particle-induced inflammation is unclear; therefore, the aim of this study was to examine the hypothesis that DHA downregulates macrophage inflammatory responses by altering phagolysosomal membrane permeability (LMP) and shifting macrophage phenotype. Isolated Balb/c alveolar macrophages (AM) were polarized into M1, M2a, M2b, or M2c phenotypes in vitro, treated with DHA, and exposed to a multi-walled carbon nanotube (MWNCT) or crystalline silica (SiO₂). Results showed minimal cytotoxicity, robust effects for silica particle uptake, and LMP differences between phenotypes. Docosahexaenoic acid prevented these effects to the greatest extent in M2c phenotype. To determine if DHA affected inflammation similarly in vivo, Balb/c mice were placed on a control or 1% DHA diet for 3 weeks, instilled with the same particles, and assessed 24 hr following instillation. Data demonstrated that in contrast to in vitro findings, DHA increased pulmonary inflammation and LMP. These results suggest that pulmonary responses in vivo may not necessarily be predicted from single-cell responses in vitro.

Length difference of multi-walled carbon nanotubes generates differential cytotoxic responses

Carbon nanotubes have recently been rated as an effective biomaterial owing to their functionalization ability. However, the safety of multi-walled carbon nanotubes (MWCNTs) has yet to be clearly understood. To investigate how cells differentially react to minor geometric differences, we prepared well-dispersed and stable long and short MWCNTs showing an approximately 100-nm length difference in an in vitro system. Through an optimal combination of bovine serum albumin (BSA) and fetal bovine serum (FBS) biosurfactants and ultrasonication, we first confirmed that the MWCNTs were maintained without aggregation throughout the experiments. Internalized MWCNTs in human coronary artery smooth muscle cells were then quantified in a label-free manner using coherent anti-Stokes Raman scattering, followed by an analysis of their localization via two-photon excitation fluorescence. Intracellular MWCNTs were found to primarily localize in mitochondria with abnormal morphologies. Mitochondrial dysfunction, which was found to result from early stages of oxidative stress that consequently lead to cell death, was then proved via decreasing mitochondrial membrane potentials, with short MWCNTs showing significantly greater cytotoxicity than long MWCNTs. Our results suggest that even small length differences of MWCNTs may lead to differential responses in cells.

Bending Properties of Carbon Nanotube/Polymer Composites with Various Aspect Ratios and Filler Contents

The key characteristics of bending sensors are piezoresistive effect, hysteresis, and durability. In this study, to investigate the influence of the aspect ratio and contents of multi-walled nanotubes (MWNTs) on the properties of bending sensors, MWNT/polydimethylsiloxane (PDMS) composites were fabricated with various aspect ratios and filler contents. The MWNTs were uniformly dispersed in the composites using the three-roll milling method. By increasing the bending angle gradually, the sensitivity of each composite was analyzed. Furthermore, discontinuous cyclic bending tests were conducted to investigate the piezoresistive effect and hysteresis. In addition, stable repeatability of the composites was confirmed through continuous cyclic bending tests. As a result, optimal aspect ratios and filler contents have been presented for application in bending sensors of MWNT composites.

Co-exposure to multi-walled carbon nanotube and lead ions aggravates hepatotoxicity of nonalcoholic fatty liver via inhibiting AMPK/PPARγ pathway

Multi-walled carbon nanotubes (MWCNTs) have been widely used in sewage disposal, water purification, and disinfection. Co-exposure to MWCNTs and heavy metal ions is common during water disposal. However, the hepatotoxicity of co-exposure to MWCNTs and lead ions for nonalcoholic fatty liver disease (NAFLD) subjects has not been investigated. NAFLD mice were fed intragastrically with MWCNTs and lead acetate (PbAc). Combined administration of MWCNTs and PbAc significantly damaged the liver function, and aggravated the nonalcoholic steatohepatitis phenotype as well as the hepatic fibrosis and steatosis in NAFLD mice. Furthermore, MWCNTs and PbAc significantly induced apoptosis in primary hepatocytes isolated from NAFLD mice. Combined administration of MWCNTs and PbAc also resulted in hepatic lipid peroxidation by inducing antioxidant defense system dysfunction, and significantly enhanced the expression levels of inflammatory cytokines in NAFLD mice livers. Meanwhile, combined administration of MWCNTs and PbAc may exert its hepatotoxicity in the NAFLD via inhibiting the adenosine 5'-monophosphate activated protein kinase (AMPK)/peroxisome proliferator-activated receptors γ (PPARγ) pathway. Taken together, we conclude that co-exposure to MWCNTs and PbAc can remarkably aggravate the hepatotoxicity in NAFLD mice via inhibiting the AMPK/PPARγ pathway. This study may provide a biosafety evaluation for the application of nanomaterials in wastewater treatment.

Cellular Responses of Human Lymphatic Endothelial Cells to Carbon Nanomaterials

One of the greatest challenges to overcome in the pursuit of the medical application of carbon nanomaterials (CNMs) is safety. Particularly, when considering the use of CNMs in drug delivery systems (DDSs), evaluation of safety at the accumulation site is an essential step. In this study, we evaluated the toxicity of carbon nanohorns (CNHs), which are potential DDSs, using human lymph node endothelial cells that have been reported to accumulate CNMs, as a comparison to fibrous, multi-walled carbon nanotubes (MWCNTs) and particulate carbon black (CB). The effect of different surface characteristics was also evaluated using two types of CNHs (untreated and oxidized). In the fibrous MWCNT, cell growth suppression, as well as expression of inflammatory cytokine genes was observed, as in previous reports. In contrast, no significant toxicity was observed for particulate CB and CNHs, which was different from the report of CB cytotoxicity in vascular endothelial cells. These results show that (1) lymph endothelial cells need to be tested separately from other endothelial cells for safety evaluation of nanomaterials, and (2) the potential of CNHs as DDSs.

Mode II Interfacial Fracture Toughness of Multi-Walled Carbon Nanotubes Reinforced Nanocomposite Film on Aluminum Substrate

In this investigation, various loadings of multi-walled carbon nanotubes (MWCNTs) ranging from 0.3–1.0 wt % were incorporated into the epoxy to fabricate the nanocomposites. Nanocomposite film with a thickness of 0.2 mm was deposited on an aluminum substrate through a hot-pressing process. Theoretical expression of the model II strain energy release rate for the film/substrate composite structure was derived. End-notched flexure (ENF) tests were performed to characterize the mode II fracture energy of the composite structure. Experimental results indicate that the elastic modulus, ultimate strength, and mode II fracture energy increase as the MWCNT loading in the nanocomposite increases. In the case of nanocomposite film with 1.0 wt % of MWCNTs, the elastic modulus, ultimate strength, and mode II interfacial fracture toughness are increased by 20.6%, 21.1%, and 54.4%, respectively in comparison with neat epoxy. In addition, the dispersion of MWCNTs in the epoxy-based matrix was investigated using scanning electron microscope (SEM). The SEM images depict that MWCNTs are well dispersed leading to the enhancement of the mechanical properties of the nanocomposite.

Simultaneous Determination of Four DNA bases at Graphene Oxide/Multi-Walled Carbon Nanotube Nanocomposite-Modified Electrode

In this study, we developed a modified glassy carbon electrode (GCE) with graphene oxide, multi-walled carbon nanotube hybrid nanocomposite in chitosan (GCE/GO-MWCNT-CHT) to achieve simultaneous detection of four nucleobases (i.e., guanine (G), adenine (A), thymine (T) and cytosine (C)) along with uric acid (UA) as an internal standard. The nanocomposite was characterized using TEM and FT-IR. The linearity ranges were up to 151.0, 78.0, 79.5, 227.5, and 162.5 µM with a detection limit of 0.15, 0.12, 0.44, 4.02, 4.0, and 3.30 µM for UA, G, A, T, and C, respectively. Compared to a bare GCE, the nanocomposite-modified GCE demonstrated a large enhancement (~36.6%) of the electrochemical active surface area. Through chronoamperometric studies, the diffusion coefficients (D), standard catalytic rate constant (K_s), and heterogenous rate constant (K_h) were calculated for the analytes. Moreover, the nanocomposite-modified electrode was used for simultaneous detection in human serum, human saliva, and artificial saliva samples with recovery values ranging from 95% to 105%.

An electrochemical sensor for the determination of tartrazine based on CHIT/GO/MWCNTs/AuNPs composite film modified glassy carbon electrode

A novel nanocomposite film of chitosan/graphene oxide (CHIT/GO)/multi-walled carbon nanotubes (MWCNTs)/gold nanoparticles (AuNPs) was applied to fabricate glassy carbon electrode (CHIT/GO/MWCNTs/AuNPs/GCE) for the determination of Tartrazine (TZ), synthetic dyes in food products. The electrochemical sensors found it to be highly sensitive by combining the signal amplification properties of GO and the excellent electronic and antifouling properties of MWCNTs. The CHIT/GO/MWCNTs/AuNPs/GCE exhibited as superior electron transfer materials and possesses intercalation properties which provide synergistic influence on the increment of the current signals. The optimum conditions were found at pH 7, 30 s, and 0.3 Vs^-1. The modified GCE obtained with a linear response ranging from 10 to 100 mg mL^-1 (r² = 0.99037) with a sensitivity of 0.018 μA μM^-1. The limit of detection (LOD) and quantification obtained were 1.45 and 4.83 mg mL^-1, respectively. The determination of TZ in spiked samples was reliable with recovery percentage from 94.52 to 109.0%. The developed sensor successfully tested in the determination of TZ analyte in commercial candy, jelly, and soft drinks with acceptable results.

Multi-walled carbon nanotube-based systems for improving the controlled release of insoluble drug dipyridamole

Applicability of multi-walled carbon nanotubes (MWCNTs) in loading dipyridamole (DDM), a poorly soluble drug, was evaluated. Additionally, the effect of drug-loading efficiency on the release behavior of the MWCNT-DDM system was also investigated. DDM as a model drug was incorporated into MWCNTs with different drug-loading rates (10, 25 and 50%) using the solvent deposition method. The MWCNT-DDM system was successfully established and characterized using common solid-state characterization methods. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption analysis and Fourier transform-infrared (FT-IR) spectroscopy were carried out to observe the progress of drug loading. X-ray diffraction (XRD) and differential scanning calorimetry (DSC) were used to systematically assess the crystalline state of the DDM after being loaded into the MWCNTs. Improvements in dissolution rate were evaluated by the dissolution test. The results revealed that with the increase of drug loading, the form of DDM in the MWCNTs changed from amorphous to crystalline state. Also, the release rate of DDM decreased upon increasing the drug-loading rate of carriers. In conclusion, MWCNTs are proven to be promising carriers for loading DDM.

Voltammetric determination of phenylephrine hydrochloride using a multi-walled carbon nanotube-modified carbon paste electrode

A chemically modified carbon paste electrode (CPE) was designed by mixing graphite and multi-walled carbon nanotubes (MWCNT). The electrochemical behaviour was studied, and the determination method of phenylephrine hydrochloride (PHE) on this sensor was established. According to the results, the optimal ratio of MWCNTs was approximately 12.5% (w/w). MWCNT-modified carbon paste electrodes (MWCNT-CPEs) showed high electrochemical activity for PHE, producing a sharp oxidation peak current (I _p) at approximately +0.816 V versus a saturated calomel electrode (SCE) reference electrode in phosphate buffer solution (PBS, pH 6.45), and the I _p increased by approximately two times compared to that of the bare CPE. The anodic I _p was linearly related with 5.0 × 10^-6-7.5 × 10^-4 mol l^-1 PHE, with a detection limit of 3.7 × 10^-7 mol l^-1. Furthermore, MWCNT-CPEs were successfully applied to the determination of PHE in injection, eye drop and nasal spray liquid samples as a simple, rapid and low-cost method.

Synthesis and Characterization of Multi-Walled Carbon Nanotube/Graphene Nanoplatelet Hybrid Film for Flexible Strain Sensors

Graphene nanoplatelet (GNP) and multi-walled carbon nanotube (MWCNT) hybrid films were prepared with the aid of surfactant Triton X-100 and sonication through a vacuum filtration process. The influence of GNP content ranging from 0 to 50 wt.% on the mechanical and electrical properties was investigated using the tensile test and Hall effect measurement, respectively. It showed that the tensile strength of the hybrid film is decreasing with the increase of the GNP content while the electrical conductivity exhibits an opposite trend. The effectiveness of the MWCNT/GNP hybrid film as a strain sensor is presented. The specimen is subjected to a flexural loading, and the electrical resistance measured by a two-point probe method is found to be function of applied strain. Experimental results demonstrate that there are two different linear strain-sensing stages (0⁻0.2% and 0.2⁻1%) in the resistance of the hybrid film with applied strain. The strain sensitivity is increasing with the increase of the GNP content. In addition, the repeatability and stability of the strain sensitivity of the hybrid film were conformed through the cyclic loading⁻unloading tests. The MWCNT/GNP hybrid film shows promising application for strain sensing.

Properties and Fabrication of PA66/Surface-Modified Multi-Walled Nanotubes Composite Fibers by Ball Milling and Melt-Spinning

PA66/surface-modified multi-walled carbon nanotubes (MWNTs) composite fibers with a better dispersion and a stronger interfacial interaction between MWNTs and polyamide 66 (PA66) matrix were fabricated via the method of ball milling and melt-spinning. The effects of unmodified (U-MWNTs), acid-modified (MWNTs-COOH) and sodium dodecyl benzenesulfonate-modified MWNTs (MWNTs-SDBS) on the physical mechanical and thermal properties of PA66 were investigated. The results show that, the surface modified nanotube can provide homogeneous dispersion and there is a strong interfacial bonding between PA66 and MWNTs-COOH. A homogeneous dispersion of MWNTs in PA66 matrices without agglomeration is obtained by a facile ball milling method, which can increase the utilization ratio of MWNTs, reduce the required amount of MWNTs and ultimately improve the mechanical properties at a lower filler loading. The tensile strength of composite fibers reaches a maximum which respectively improved by 27% and 24% than that of PA66 fibers, when the mass fraction of MWNTs-SDBS and MWNTs-COOH is 0.1%. It is helpful for decrease the producing cost of the composite fibers. Moreover, the incorporation of MWNTs into PA66 improves the crystallizing temperature, crystallinity and thermal stability. The research shows that a novel facile method is developed for the fabrication of polymer composite fiber.

Establishment of an in vivo simulating co-culture assay platform for genotoxicity of multi-walled carbon nanotubes

Engineered nanomaterials (ENM) are now used in a wide variety of fields, and, thus, their safety should urgently be assessed and secured. It has been suggested that inflammatory responses via the phagocytosis of ENM by macrophages is a key mechanism for their genotoxicity. The present study was conducted to establish a mechanism‐based assay to evaluate the genotoxicity of ENM under conditions simulating an in vivo situation, featuring a co‐culture system of murine lung resident cells (GDL1) and immune cells (RAW264.7). GDL1 were cultured with or without RAW264.7, exposed to a multi‐walled carbon nanotube (MWCNT), and then analyzed for mutagenicity and underlying mechanisms. Mutation frequencies induced in GDL1 by the MWCNT were significantly greater with the co‐existence of RAW264.7 than in its absence. Mutation spectra observed in GDL1 co‐cultured with RAW264.7 were different from those seen in GDL1 cultured alone, but similar to those observed in the lungs of mice exposed to the MWCNT in vivo. Inflammatory cytokines, such as IL‐1β and TNF‐α, were produced from RAW264.7 cells treated with the MWCNT. The generation of reactive oxygen species and the formation of 8‐oxodeoxyguanosine in GDL1 exposed to the MWCNT were greater in the co‐culture conditions than in the single culture conditions. Based on these findings, it is indicated that inflammatory responses are involved in the genotoxicity of MWCNT, and that the presently established, novel in vitro assay featuring a co‐culture system of tissue resident cells with immune cells is suitable to evaluate the genotoxicity of ENM.

Effect of Novel Quercetin Titanium Dioxide-Decorated Multi-Walled Carbon Nanotubes Nanocomposite on Bacillus subtilis Biofilm Development

The present work was targeted to design a surface against cell seeding and adhering of bacteria, Bacillus subtilis. A multi-walled carbon nanotube/titanium dioxide nano-power was produced via simple mixing of carbon nanotube and titanium dioxide nanoparticles during the sol-gel process followed by heat treatment. Successfully, quercetin was immobilized on the nanocomposite via physical adsorption to form a quercetin/multi-walled carbon nanotube/titanium dioxide nanocomposite. The adhesion of bacteria on the coated-slides was verified after 24 h using confocal laser-scanning microscopy. Results indicated that the quercetin/multi-walled carbon nanotube/titanium dioxide nanocomposite had more negativity and higher recovery by glass surfaces than its counterpart. Moreover, coating surfaces with the quercetin-modified nanocomposite lowered both hydrophilicity and surface-attached bacteria compared to surfaces coated with the multi-walled carbon nanotubes/titanium dioxide nanocomposite.

Macrophage polarization and activation at the interface of multi-walled carbon nanotube-induced pulmonary inflammation and fibrosis

Pulmonary exposure to carbon nanotubes (CNTs) induces fibrosing lesions in the lungs that manifest rapid-onset inflammatory and fibrotic responses, leading to chronic fibrosis in animals and health concerns in exposed humans. The mechanisms underlying CNT-induced fibrogenic effects remain undefined. Macrophages are known to play important roles in immune regulation and fibrosis development through their distinct subsets. Here we investigated macrophage polarization and activation in mouse lungs exposed to multi-walled CNTs (MWCNTs). Male C57BL/6J mice were treated with MWCNTs (XNRI MWNT-7) at 40 μg per mouse (∼1.86 mg/kg body weight) by oropharyngeal aspiration. The treatment stimulated prominent acute inflammatory and fibrotic responses. Moreover, it induced pronounced enrichment and polarization of macrophages with significantly increased M1 and M2 populations in a time-dependent manner. Induction of M1 polarization was apparent on day 1 with a peak on day 3, but declined rapidly thereafter. On the other hand, the M2 polarization was induced on day 1 modestly, but was remarkably elevated on day 3 and maintained at a high level through day 7. M1 and M2 macrophages were functionally activated by MWCNTs as indicated by the expression of their distinctive functional markers, such as iNOS and ARG1, with time courses parallel to M1 and M2 polarization, respectively. Molecular analysis revealed MWCNTs boosted specific STAT and IRF signaling pathways to regulate M1 and M2 polarization in the lungs. These findings suggest a new mechanistic connection between inflammation and fibrosis induced by MWCNTs through the polarization and activation of macrophages during MWCNT-induced lung pathologic response.

Synthesis and Properties of Carbon Nanotube-Grafted Silica Nanoarchitecture-Reinforced Poly(Lactic Acid)

A novel nanoarchitecture-reinforced poly(lactic acid) (PLA) nanocomposite was prepared using multi-walled carbon nanotube (MWCNT)-grafted silica nanohybrids as reinforcements. MWCNT-grafted silica nanohybrids were synthesized by the generation of silica nanoparticles on the MWCNT surface through the sol-gel technique. This synthetic method involves organo-modified MWCNTs that are dispersed in tetrahydrofuran, which incorporates tetraethoxysilane that undergoes an ultrasonic sol-gel process. Gelation yielded highly dispersed silica on the organo-modified MWCNTs. The structure and properties of the nanohybrids were established using ²⁹Si nuclear magnetic resonance, Raman spectroscopy, wide-angle X-ray diffraction, thermogravimetric analysis, and transmission electron microscopy. The resulting MWCNT nanoarchitectures were covalently assembled into silica nanoparticles, which exhibited specific and controllable morphologies and were used to reinforce biodegradable PLA. The tensile strength and the heat deflection temperature (HDT) of the PLA/MWCNT-grafted silica nanocomposites increased when the MWCNT-grafted silica was applied to the PLA matrix; by contrast, the surface resistivity of the PLA/MWCNT-grafted silica nanocomposites appeared to decline as the amount of MWCNT-grafted silica in the PLA matrix increased. Overall, the reinforcement of PLA using MWCNT-grafted silica nanoarchitectures was efficient and improved its mechanical properties, heat resistance, and electrical resistivity.

Fracture Analysis of MWCNT/Epoxy Nanocomposite Film Deposited on Aluminum Substrate

Multi-walled carbon nanotube (MWCNT) reinforced epoxy films were deposited on an aluminum substrate by a hot-pressing process. Three-point bending tests were performed to determine the Young’s modulus of MWCNT reinforced nanocomposite films. Compared to the neat epoxy film, nanocomposite film with 1 wt % of MWCNT exhibits an increase of 21% in the Young’s modulus. Four-point-bending tests were conducted to investigate the fracture toughness of the MWCNT/epoxy nanocomposite film deposited on an aluminum substrate with interfacial cracks. Based on the Euler-Bernoulli beam theory, the strain energy in a film/substrate composite beam is derived. The difference of strain energy before and after the propagation of the interfacial crack are calculated, leading to the determination of the strain energy release rate. Experimental test results show that the fracture toughness of the nanocomposite film deposited on the aluminum substrate increases with the increase in the MWCNT content.

TIMP1 promotes multi-walled carbon nanotube-induced lung fibrosis by stimulating fibroblast activation and proliferation

Pulmonary exposure to multi-walled carbon nanotubes (MWCNTs) may cause fibrosing lesions in animal lungs, raising health concerns about such exposure in humans. The mechanisms underlying fibrosis development remain unclear, but they are believed to involve the dysfunction of fibroblasts and myofibroblasts. Using a mouse model of MWCNT exposure, we found that the tissue inhibitor of metalloproteinase 1 (Timp1) gene was rapidly and highly induced in the lungs by MWCNTs in a time- and dose-dependent manner. Concomitantly, a pronounced elevation of secreted TIMP1 was observed in the bronchoalveolar lavage (BAL) fluid and serum. Knockout (KO) of Timp1 in mice caused a significant reduction in fibrotic focus formation, collagen fiber deposition, recruitment of fibroblasts and differentiation of fibroblasts into myofibroblasts in the lungs, indicating that TIMP1 plays a critical role in the pulmonary fibrotic response to MWCNTs. At the molecular level, MWCNT exposure significantly increased the expression of the cell proliferation markers Ki-67 and PCNA and a panel of cell cycle-controlling genes in the lungs in a TIMP1-dependent manner. MWCNT-stimulated cell proliferation was most prominent in fibroblasts but not myofibroblasts. Furthermore, MWCNTs elicited a significant induction of CD63 and integrin β1 in lung fibroblasts, leading to the formation of a TIMP1/CD63/integrin β1 complex on the surface of fibroblasts in vivo and in vitro, which triggered the phosphorylation and activation of Erk1/2. Our study uncovers a new pathway through which induced TIMP1 critically modulates the pulmonary fibrotic response to MWCNTs by promoting fibroblast activation and proliferation via the TIMP1/CD63/integrin β1 axis and ERK signaling.

The Dispersion State of Tangled Multi-Walled Carbon Nanotubes Affects Their Cytotoxicity

The medical applications of carbon nanotubes (CNTs) have garnered much attention. However, evaluating the safety of CNTs remains difficult, and no consensus has been reached. Moreover, assessing the biosafety of multi-walled CNTs (MWCNTs), which can become tangled during manufacturing, is challenging because they do not readily disperse. We studied how the dispersion state of tangled MWCNTs affects their cytotoxicity, using three sonicators. Flotube 9110 (FT9110), tangled MWCNTs, were dispersed in two dispersants (fetal bovine serum and polysorbate 80) using a new type of sonicator (PR-1) and two conventional sonicators. The size and cytotoxicity of the dispersed FT9110 were measured using the BEAS-2B human bronchial epithelial cell line. The PR-1 dispersed the FT9110 to agglomerates <200 nm in diameter; FT9110 dispersed with the PR-1 did not show cytotoxicity regardless of dispersant. The other sonicators dispersed the FT9110 to particles >1000 nm in diameter, and cytotoxicity depended on the dispersant. We found that excluding cells adhered to agglomerated FT9110 before evaluating cytotoxicity can lead to false-positive results. The PR-1 sonicator dispersed tangled FT9110 to many single fibers, which showed lower cytotoxicity than conventionally-sonicated MWCNTs. We suggest that dispersion state should be accounted for when evaluating the cytotoxicity of MWCNTs.

A Label-Free Microelectrode Array Based on One-Step Synthesis of Chitosan-Multi-Walled Carbon Nanotube-Thionine for Ultrasensitive Detection of Carcinoembryonic Antigen

Carcinoembryonic antigen (CEA) has been an extensively used tumor marker responsible for clinical early diagnosis of cervical carcinomas, and pancreatic, colorectal, gastric and lung cancer. Combined with micro-electro mechanical system (MEMS) technology, it is important to develop a novel immune microelectrode array (MEA) not only for rapid analysis of serum samples, but also for cell detection in vitro and in vivo. In this work, we depict a simple approach to modify chitosan–multi-walled carbon nanotubes–thionine (CS–MWCNTs–THI) hybrid film through one-step electrochemical deposition and the CS-MWCNTs-THI hybrid films are successfully employed to immobilize anti-CEA for fabricating simple, label-free, and highly sensitive electro-chemical immune MEAs. The detection principle of immune MEA was based on the fact that the increasing formation of the antigen-antibody immunocomplex resulted in the decreased response currents and the relationship between the current reductions with the corresponding CEA concentrations was directly proportional. Experimental results indicated that the label-free MEA had good selectivity and the limit of detection for CEA is 0.5 pg/mL signal to noise ratio (SNR) = 3. A linear calibration plot for the detection of CEA was obtained in a wide concentration range from 1 pg/mL to 100 ng/mL (r = 0.996). This novel MEA has potential applications for detecting CEA for the research on cancer cells and cancer tissue slices as well as for effective early diagnosis.

Long-term retention of pristine multi-walled carbon nanotubes in rat lungs after intratracheal instillation

As a result of the growing potential industrial and medical applications of multi‐walled carbon nanotubes (MWCNTs), people working in or residing near facilities that manufacture them may be exposed to airborne MWCNTs in the future. Because of concerns regarding their toxicity, quantitative data on the long‐term clearance of pristine MWCNTs from the lungs are required. We administered pristine MWCNTs well dispersed in 0.5 mg ml⁻¹ Triton‐X solution to rats at doses of 0.20 or 0.55 mg via intratracheal instillation and investigated clearance over a 12‐month observation period. The pristine MWCNTs pulmonary burden was determined 1, 3, 7, 28, 91, 175 and 364 days after instillation using a method involving combustive oxidation and infrared analysis, combined with acid digestion and heat pretreatment. As 0.15‐ and 0.38‐mg MWCNTs were detected 1 day after administration of 0.20 and 0.55 mg MWCNTs, respectively, approximately 30% of administrated MWCNTs may have been cleared by bronchial ciliary motion within 24 h of administration. After that, the pulmonary MWCNT burden did not decrease significantly over time for up to 364 days after instillation, suggesting that MWCNTs were not readily cleared from the lung. Transmission electron microscopy (TEM) showed that alveolar macrophages internalized the MWCNTs and retained in the lung for at least 364 days after instillation. MWCNTs were not detected in the liver or brain within the 364‐day study period (<0.04 mg per liver, < 0.006 mg per brain). Copyright © 2015 The Authors Journal of Applied Toxicology Published by John Wiley & Sons Ltd.

Well‐dispersed pristine MWCNTs were administered to rats at doses of 0.20 or 0.55 mg via intratracheal instillation, and investigated clearance over a 12‐month observation period. Approximately 30% of administrated MWCNTs may have been cleared by bronchial ciliary motion within 24 h of administration. After that, the pulmonary MWCNT burden did not decrease significantly over time for up to 364 days after instillation, suggesting that MWCNTs were not readily cleared from the lung. MWCNTs were not detected in the liver or brain within the 364‐day study period.

Analysis of the Sensitivity of K-Type Molecular Sieve-Deposited MWNTs for the Detection of SF₆ Decomposition Gases under Partial Discharge

Sulfur hexafluoride (SF6) is widely utilized in gas-insulated switchgear (GIS). However, part of SF6 decomposes into different components under partial discharge (PD) conditions. Previous research has shown that the gas responses of intrinsic and 4 Å-type molecular sieve-deposited multi-wall carbon nanotubes (MWNTs) to SOF2 and SO2F2, two important decomposition components of SF6, are not obvious. In this study, a K-type molecular sieve-deposited MWNTs sensor was developed. Its gas response characteristics and the influence of the mixture ratios of gases on the gas-sensing properties were studied. The results showed that, for sensors with gas mixture ratios of 5:1, 10:1, and 20:1, the resistance change rate increased by nearly 13.0% after SOF2 adsorption, almost 10 times that of MWNTs sensors, while the sensors' resistance change rate with a mixture ratio of 10:1 reached 17.3% after SO2F2 adsorption, nearly nine times that of intrinsic MWNT sensors. Besides, a good linear relationship was observed between concentration of decomposition components and the resistance change rate of sensors.

Drug targeting to arthritic region via folic acid appended surface-engineered multi-walled carbon nanotubes

This study was aimed at developing and investigating folate anchored carbon nanotubes for targeting an anti-arthritic drug, Methotrexate (MTX) to inflammatory arthritic region. The folic acid (FA) was conjugated to amidated multi-walled carbon nanotubes (MWCNTs) and confirmed by Fourier transform infrared (FTIR), (1)H NMR spectroscopy and X-ray diffraction analysis. The MTX was loaded into the pristine and functionalized-MWCNTs and extensively characterized in vitro and in vivo studies. The drug entrapment efficiency was found high in folate conjugated MWCNTs. In vitro drug release in PBS (pH 7.4) from pristine MWCNTs and folate conjugated MWCNTs formulation was found to be 66.35 ± 2.3 and 56.88 ± 1.9% in 24 h, respectively. Folate conjugated MWCNTs significantly increased (p < 0.005) the percentage inhibition of arthritis, biological half-life and volume of distribution of MTX as compared to MTX-loaded naked MWCNTs as well as free MTX. In in vivo biodistribution studies, MTX was found to be significantly higher (p < 0.005) in arthritic joints from folate functionalized MWCNTs as compared to free drug as well as drug-loaded naked MWCNTs. The present outcomes highlights the propensity of drug-loaded functionalized MWCNTs to alter the pharmacokinetics as well as sustained and targeted drug delivery system as well.

The increases in relative mRNA expressions of inflammatory cytokines and chemokines in splenic macrophages from rats exposed to multi-walled carbon nanotubes by whole-body inhalation for 13 weeks

BACKGROUND

The toxicity of multi-walled carbon nanotubes (MWCNT) may be related to the immune system. The objective of this study was to obtain information for immunotoxic mechanisms of MWCNT in situ.

METHODS

Using whole-body inhalation, male and female rats were exposed to 0, 0.2, 1 or 5 mg MWCNT/m³ for 13 weeks. Thereafter, spleens were recovered from the rats. Real-time PCR was done to assess expression of TNFα, IL-1β, IL-6, IL-10, MCP-1 and MIP-1α mRNA in the splenic macrophages; splenic T-lymphocytes were examined for IL-2 and TGF-β1 mRNA expression.

RESULTS

The relative expression of IL-1β mRNA in the cells from female rats exposed to 5 mg MWCNT/m³ was significantly higher than that in control cells. For IL-6 and IL-10, cells from rats in the 0.2 and 5 mg MWCNT/m³ had significantly higher mRNA expressions than did cells from controls. Expression of IL-1β, IL-6 and TNFα genes in cells from males in all exposure groups were higher than in control cells. Expression of MIP-1α in the cells from female 5-mg group was significantly higher than that in cells in the control. Only IL-2 was expression reduced, i.e. cells from male and female rats in all MWCNT groups had significantly lower mRNA expressions than control cells.

CONCLUSIONS

Systemic inflammation would likely occur in rats (or other hosts) exposed to MWCNT via inhalation due to increases in the expression of inflammatory cytokines in splenic macrophages. Moreover, decreases in IL-2 expression in T-lymphocytes may be critical to the potential reductions in anti-tumor responses in MWCNT-exposed hosts.

Exploiting the hierarchical morphology of single-walled and multi-walled carbon nanotube films for highly hydrophobic coatings

Self-assembled hierarchical solid surfaces are very interesting for wetting phenomena, as observed in a variety of natural and artificial surfaces. Here, we report single-walled (SWCNT) and multi-walled carbon nanotube (MWCNT) thin films realized by a simple, rapid, reproducible, and inexpensive filtration process from an aqueous dispersion, that was deposited at room temperature by a dry-transfer printing method on glass. Furthermore, the investigation of carbon nanotube films through scanning electron microscopy (SEM) reveals the multi-scale hierarchical morphology of the self-assembled carbon nanotube random networks. Moreover, contact angle measurements show that hierarchical SWCNT/MWCNT composite surfaces exhibit a higher hydrophobicity (contact angles of up to 137°) than bare SWCNT (110°) and MWCNT (97°) coatings, thereby confirming the enhancement produced by the surface hierarchical morphology.

Biological responses according to the shape and size of carbon nanotubes in BEAS-2B and MESO-1 cells

This study aimed to investigate the influence of the shape and size of multi-walled carbon nanotubes (MWCNTs) and cup-stacked carbon nanotubes (CSCNTs) on biological responses in vitro. Three types of MWCNTs – VGCF^®-X, VGCF^®-S, and VGCF^® (vapor grown carbon fibers; with diameters of 15, 80, and 150 nm, respectively) – and three CSCNTs of different lengths (CS-L, 20–80 μm; CS-S, 0.5–20 μm; and CS-M, of intermediate length) were tested. Human bronchial epithelial (BEAS-2B) and malignant pleural mesothelioma cells were exposed to the CNTs (1–50 μg/mL), and cell viability, permeability, uptake, total reactive oxygen species/superoxide production, and intracellular acidity were measured. CSCNTs were less toxic than MWCNTs in both cell types over a 24-hour exposure period. The cytotoxicity of endocytosed MWCNTs varied according to cell type/size, while that of CSCNTs depended on tube length irrespective of cell type. CNT diameter and length influenced cell aggregation and injury extent. Intracellular acidity increased independently of lysosomal activity along with the number of vacuoles in BEAS-2B cells exposed for 24 hours to either CNT (concentration, 10 μg/mL). However, total reactive oxygen species/superoxide generation did not contribute to cytotoxicity. The results demonstrate that CSCNTs could be suitable for biological applications and that CNT shape and size can have differential effects depending on cell type, which can be exploited in the development of highly specialized, biocompatible CNTs.

Carbon nanotubes as VEGF carriers to improve the early vascularization of porcine small intestinal submucosa in abdominal wall defect repair

Insufficient early vascularization in biological meshes, resulting in limited host tissue incorporation, is thought to be the primary cause for the failure of abdominal wall defect repair after implantation. The sustained release of exogenous angiogenic factors from a biocompatible nanomaterial might be a way to overcome this limitation. In the study reported here, multiwalled carbon nanotubes (MWNT) were functionalized by plasma polymerization to deliver vascular endothelial growth factor₁₆₅ (VEGF₁₆₅). The novel VEGF₁₆₅-controlled released system was incorporated into porcine small intestinal submucosa (PSIS) to construct a composite scaffold. Scaffolds incorporating varying amounts of VEGF₁₆₅-loaded functionalized MWNT were characterized in vitro. At 5 weight percent MWNT, the scaffolds exhibited optimal properties and were implanted in rats to repair abdominal wall defects. PSIS scaffolds incorporating VEGF₁₆₅-loaded MWNT (VEGF–MWNT–PSIS) contributed to early vascularization from 2–12 weeks postimplantation and obtained more effective collagen deposition and exhibited improved tensile strength at 24 weeks postimplantation compared to PSIS or PSIS scaffolds, incorporating MWNT without VEGF₁₆₅ loading (MWNT–PSIS).

Removal of boron from aqueous solution using magnetic carbon nanotube improved with tartaric acid

Boron removal capacity of multi-walled carbon nanotubes (MWCNTs) modified with tartaric acid was investigated in this study. Modification of MWCNTs with tartaric acid was confirmed by Boehm surface chemistry method and fourier transform infra-red (FT-IR) spectroscopy. Experiments were performed to determine the adsorption isotherm and adsorption thermodynamic parameters of boron adsorption on tartaric acid modified MWCNTs (TA-MWCNTs). The effect of variables including initial pH, dosage of adsorbent, contact time and temperature was investigated. Analysis of data showed that adsorption equilibrium could be better described by Freundlich isotherm and the maximum adsorption capacities obtained at the pH of 6.0 was 1.97 mg/g. The estimated thermodynamic values of free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) indicated a spontaneous and an endothermic process. Furthermore, the TA-MWCNTs was magnetized for separation of boron-contaminated adsorbent from aqueous solution by applying magnetic field. The results showed that magnetic TA-MWCNTs particles were separated effectively after adsorption from contaminated water.

Two-week Toxicity of Multi-walled Carbon Nanotubes by Whole-body Inhalation Exposure in Rats

To evaluate pulmonary toxicity of multi-walled carbon nanotubes (MWCNTs), F344 rats of both sexes were exposed by inhalation to 0.2, 1 or 5 mg/m³ MWCNT aerosol for 6 h/day, 5 days/week for 2 weeks using a whole-body exposure system. At the end of the 2-week exposure period, one-half of the rats were necropsied, and at the end of an additional 4-week postexposure period, the remaining rats were necropsied. MWCNTs were deposited in the lungs of all MWCNT-exposed groups and mostly remained in the lungs throughout the 4-week postexposure period. Granulomatous changes in the lung were found in the rats exposed to 5 mg/m³ MWCNTs, and these changes were slightly aggravated at the end of the 4-week postexposure period. In the bronchoalveolar lavage fluid (BALF), the numbers of neutrophils, percentages of bi- and multinucleated alveolar macrophages, levels of ALP activity and concentrations of total protein and albumin were elevated in the rats exposed to 1 and 5 mg/m³ MWCNTs. At the end of the 4-week postexposure period, the values of the BALF parameters tended to remain elevated. In addition, goblet cell hyperplasias in the nasal cavity and nasopharynx were observed in the rats exposed to 1 and 5 mg/m³ MWCNTs, but these lesions had largely regressed by the end of the postexposure period. Based on the histopathological and inflammatory changes, the no-observed-adverse-effect level (NOAEL) for inhalation of MWCNTs for 2 weeks was 0.2 mg/m³.

Dynamic Behavior of Nanocomposites Reinforced with Multi-Walled Carbon Nanotubes (MWCNTs)

The influence of multi-walled carbon nanotubes (MWCNT) on the structural dynamic behavior of MWCNT/epoxy nanocomposites was investigated. Two different types of MWCNTs, pristine MWCNT and functionalized MWCNT, were used in this study. Carboxylic acid-functionalized MWCNTs (MWCNT-COOH) were obtained by oxidation pristine MWCNTs via sonication in sulfuric-nitric acid and characterized by Fourier transform infrared spectroscopy (FTIR). Dynamic behaviors of the MWCNT reinforced nanocomposite including the natural frequency and damping ratio were determined using free vibration test. Experimental results showed that the damping ratio of the nanocomposite decreases with the increase of the MWCNT addition, while the natural frequency is increasing with the increase of the MWCNT addition. Functionalized MWCNTs improved the interfacial bonding between the nanotubes and epoxy resin resulting in the reduction of the interfacial energy dissipation ability and enhancement of the stiffness.

Effects of the electrical conductivity and orientation of silicon substrate on the synthesis of multi-walled carbon nanotubes by thermal chemical vapor deposition

We studied the effects of the electrical conductivity and orientation of silicon substrate on both catalytic Fe thin film and the structure and morphology of multi-walled carbon nanotube (MWNT) grown by low-pressure chemical vapor deposition. Both p-type Si(100) and Si(111) substrates with three different doping concentrations (high, low, undoped) were used to evaluate the formation of catalytic nanoparticles and the growth of MWNTs. The morphology of catalytic nanoparticles such as size and density was characterized by field-emission scanning electron microscopy, Cs-corrected energy-filtered transmission electron microscopy, and X-ray photoelectron spectroscopy. Structural characteristics of MWNTs grown on different combinations of silicon substrate orientation and electrical conductivities (σ) were also systematically analyzed. Based on the experimental results, growth modes of MWNTs could be controlled by choosing an appropriate combination of σ and orientation of Si substrates.

Effect of dispersants of multi-walled carbon nanotubes on cellular uptake and biological responses

Although there have been many reports about the cytotoxicity of multi-walled carbon nanotubes (MWCNTs), the results are still controversial. To investigate one possible reason, the authors investigated the influence of MWCNT dispersants on cellular uptake and cytotoxicity. Cytotoxicity was examined (measured by alamarBlue^® assay), as well as intracellular MWCNT concentration and cytokine secretion (measured by flow cytometry) in human bronchial epithelial cells (BEAS-2B) exposed to a type of highly purified MWCNT vapor grown carbon fiber (VGCF^®, Shōwa Denkō Kabushiki-gaisha, Tokyo, Japan) in three different dispersants (gelatin, carboxylmethyl cellulose, and 1,2-dipalmitoyl-sn-glycero-3-phosphocholine). The authors also researched the relationship between the intracellular concentration of MWCNTs and cytotoxicity by using two cell lines, BEAS-2B and MESO-1 human malignant pleural mesothelioma cells. The intracellular concentration of VGCF was different for each of the three dispersants, and the levels of cytotoxicity and inflammatory response were correlated with the intracellular concentration of VGCF. A relationship between the intracellular concentration of VGCF and cytotoxic effects was observed in both cell lines. The results indicate that dispersants affect VGCF uptake into cells and that cytotoxicity depends on the intracellular concentration of VGCF, not on the exposed dosage. Thus, toxicity appears to depend on exposure time, even at low VGCF concentrations, because VGCF is biopersistent.