Quantum dot-induced phase stabilization of α-CsPbI3 perovskite for high-efficiency photovoltaics

Effect of ion migration on lead halide perovskite on visible light communication system

Benefiting from the high modulation bandwidth (BW), low energy consumption and excellent optical performance, lead halide perovskite has attracted wide attention in visible light communication (VLC). However, the ion migration which results in mobile point defects in perovskite structures is recognized as a crucial key factor inducing the performance degradation. Here, the influence of ion migration in perovskite devices on the performance of VLC was systematically studied. The ion migration process is realized by mixing CsPbBr3 and CsPbI3 quantum dots, during which, the performance of the VLC system is reduced, but it can return to its initial state after stabilization. The on-off keying (OOK) modulation scheme of the perovskite light-emitting diode (LED) device was carried out, achieving a data rate of 90 Mbps.

Iodotrimethylsilane as a Reactive Ligand for Surface Etching and Passivation of Perovskite Nanocrystals toward Efficient Pure-red to Deep-red LEDs

Resurfacing perovskite nanocrystals (NCs) with tight-binding and conductive ligands to resolve the dynamic ligands-surface interaction is the fundamental issue for their applications in perovskite light-emitting diodes (PeLEDs). Although various types of surface ligands have been proposed, these ligands either exhibit weak Lewis acid/base interactions or need high polar solvents for dissolution and passivation, resulting in a compromise in the efficiency and stability of PeLEDs. Herein, we report a chemically reactive agent (Iodotrimethylsilane, TMIS) to address the trade-off among conductivity, solubility and passivation using all-inorganic CsPbI3 NCs. The liquid TMIS ensures good solubility in non-polar solvents and reacts with oleate ligands and produces in situ HI for surface etching and passivation, enabling strong-binding ligands on the NCs surface. We report, as a result, red PeLEDs with an external quantum efficiency (EQE) of ≈23 %, which is 11.2-fold higher than the control, and is among the highest CsPbI3 PeLEDs. We further demonstrate the universality of this ligand strategy in the pure bromide system (CsPbBr3 ), and report EQE of ≈20 % at 640, 652, and 664 nm. This represents the first demonstration of a chemically reactive ligand strategy that applies to different systems and works effectively in red PeLEDs spanning emission from pure-red to deep-red.

Tuning the morphology, stability and optical properties of CsSnBr3 nanocrystals through bismuth doping for visible-light-driven applications

In this investigation, we have demonstrated the synthesis of lead-free CsSnBr3 (CSB) and 5 mol% bismuth (Bi) doped CSB (CSB'B) nanocrystals, with a stable cubic perovskite structure following a facile hot injection technique. The Bi substitution in CSB was found to play a vital role in reducing the size of the nanocrystals significantly, from 316 ± 93 to 87 ± 22 nm. Additionally, Bi doping has inhibited the oxidation of Sn2+ of CSB perovskite. A reduction in the optical band gap from 1.89 to 1.73 eV was observed for CSB'B and the PL intensity was quenched due to the introduction of the Bi3+ dopant. To demonstrate one of the visible-light-driven applications of the nanocrystals, photodegradation experiments were carried out as a test case. Interestingly, under UV-vis irradiation, the degradation efficiency of CSB'B was roughly one order lower than that of P25 titania nanoparticles; however, it was almost five times higher when driven by visible light under identical conditions. The water stability of CSB'B perovskite and suppression of the oxidative degradation of Sn were confirmed through XRD and XPS analyses after photocatalysis. Moreover, by employing experimental parameters, DFT-based first-principles calculations were performed, which demonstrated an excellent qualitative agreement between experimental and theoretical outcomes. The as-synthesized Bi-doped CSB might be a stable halide perovskite with potential in visible-light-driven applications.

Stable and luminescent cesium copper halide nanocrystals embedded in flexible polymer fibers for fabrication of down-converting WLEDs

Recently, CsPbX3 (X = I, Br, Cl) perovskite nanocrystals (NCs) have drawn wide attention owing to their outstanding photophysical and optoelectronic properties. However, the toxicity of such NCs remained a big challenge for further commercialization. Herein, we adopt facile methods for synthesizing green-emissive Cs3Cu2Cl5 and blue-emissive Cs3Cu2Br2.5I2.5 perovskite NCs that exhibit broad emission spectra with large Stokes shifts. These NCs showed photoluminescence quantum yields (PLQY) up to 65% (Cs3Cu2Cl5 NCs) and 32% (Cs3Cu2Br2.5I2.5 NCs) with limited stabilities. To further improve the stability, the NCs were blended with a hydrophobic polymer poly-methylmethacrylate (PMMA) and embedded inside the polymer fiber by an electrospinning process to form composite fibers. The as-prepared Cs3Cu2Cl5@PMMA and Cs3Cu2Br2.5I2.5@PMMA fiber films demonstrated good surface coverage and better thermal stability, and even retained their emission properties when dispersed in water. The emissive fibers were also deposited on flexible polyethylene terephthalate (PET) substrates that displayed high resistance towards bending and twisting with no signs of breakage, damage, or loss of optical properties. Finally, UV-pumped phosphor-converted WLEDs fabricated by using these blue and green-emitting fibers revealed CIE chromaticity coordinates at (0.27, 0.33) with a maximum luminous efficiency of 69 Lm W-1 and correlated color temperature (CCT) value of 8703 K. These outcomes can be beneficial for the development of futuristic flexible display technologies.

In situ imaging of the atomic phase transition dynamics in metal halide perovskites

Phase transition dynamics are an important concern in the wide applications of metal halide perovskites, which fundamentally determine the optoelectronic properties and stabilities of perovskite materials and devices. However, a more in-depth understanding of such a phase transition process with real atomic resolution is still limited by the immature low-dose electron microscopy and in situ imaging studies to date. Here, we apply an emergent low-dose imaging technique to identify different phase structures (α, β and γ) in CsPbI3 nanocrystals during an in-situ heating process. The rotation angles of PbI6 octahedrons can be measured in these images to quantitatively describe the thermal-induced phase distribution and phase transition. Then, the dynamics of such a phase transition are studied at a macro time scale by continuously imaging the phase distribution in a single nanocrystal. The structural evolution process of CsPbI3 nanocrystals at the particle level, including the changes in morphology and composition, is also visualized with increasing temperature. These results provide atomic insights into the transition dynamics of perovskite phases, indicating a long-time transition process with obvious intermediate states and spatial distribution that should be generally considered in the further study of structure-property relations and device performance.

Defect Driven Opto-Critical Phases Tuned for All-Solar Utilization

Materials imbued with uniformly dispersed, photo-responsive nanoparticles are instrumental in sustainable energy and photonic applications. Conventional methods, however, constrain their all-solar response. An innovative alternative is proposed: submerged photo-synthesis of crystallites (SPsC). It is shown that strategic doping with copper and oxygen vacancies can induce opto-critical phases from the nonstoichiometric tungstic acids (WO3 ·H2 O). These opto-critical phases enable a dynamic equilibrium shift in lattice defect stabilization, facilitating an unprecedented a whole solar wavelength response. This response manifests as photothermal, photo-assisted water evaporation, and photo-electrochemical characteristics. Harnessing all-solar energy, this one-pot SPsC strategy may steer the design and development of advanced oxide materials, enhancing functionality across diverse application domains.

Controllable Black-to-Yellow Phase Transition by Tuning the Lattice Symmetry in Perovskite Quantum Dots

The black-to-yellow phase transition in perovskite quantum dots (QDs) is more complex than in bulk perovskites, regarding the role of surface energy. Here, with the assistance of in situ grazing-incidence wide-angle and small-angle X-ray scattering (GIWAXS/GISAXS), distinct phase behaviors of cesium lead iodide (CsPbI3 ) QD films under two different temperature profiles-instant heating-up (IHU) and slow heating-up (SHU) is investigated. The IHU process can cause the phase transition from black phase to yellow phase, while under the SHU process, the majority remains in black phase. Detailed studies and structural refinement analysis reveal that the phase transition is triggered by the removal of surface ligands, which switches the energy landscape. The lattice symmetry determines the transition rate and the coexistence black-to-yellow phase ratio. The SHU process allows longer relaxation time for a more ordered QD packing, which helps sustain the lattice symmetry and stabilizes the black phase. Therefore, one can use the lattice symmetry as a general index to monitor the CsPbI3 QD phase transition and finetune the coexistence black-to-yellow phase ratio for niche applications.

Stable PbS colloidal quantum dot inks enable blade-coating infrared solar cells

Infrared solar cells are more effective than normal bandgap solar cells at reducing the spectral loss in the near-infrared region, thus also at broadening the absorption spectra and improving power conversion efficiency. PbS colloidal quantum dots (QDs) with tunable bandgap are ideal infrared photovoltaic materials. However, QD solar cell production suffers from small-area-based spin-coating fabrication methods and unstable QD ink. Herein, the QD ink stability mechanism was fully investigated according to Lewis acid-base theory and colloid stability theory. We further studied a mixed solvent system using dimethylformamide and butylamine, compatible with the scalable manufacture of method-blade coating. Based on the ink system, 100 cm2 of uniform and dense near-infrared PbS QDs (~ 0.96 eV) film was successfully prepared by blade coating. The average efficiencies of above absorber-based devices reached 11.14% under AM1.5G illumination, and the 800 nm-filtered efficiency achieved 4.28%. Both were the top values among blade coating method based devices. The newly developed ink showed excellent stability, and the device performance based on the ink stored for 7 h was similar to that of fresh ink. The matched solvent system for stable PbS QD ink represents a crucial step toward large area blade coating photoelectric devices.

Fostering the Dense Packing of Halide Perovskite Quantum Dots through Binary-Disperse Mixing

Due to their versatile applications, perovskite quantum dot (PQD)-based optoelectrical devices have garnered significant research attention. However, the fundamental packing behavior of PQDs in thin films and its impact on the device performance remain relatively unexplored. Drawing inspiration from theoretical models concerning packing density with size mixtures, this study presents an effective strategy, namely, binary-disperse mixing, aimed at enhancing the packing density of PQD films. Comprehensive grazing-incidence small-angle X-ray characterization suggested that the PQD film consists of three phases: two monosize phases and one binary mixing phase. The volume fraction and population of the binary-size phase can be tuned by mixing an appropriate amount of large and small PQDs. Furthermore, we performed multi-length-scale all-atom and coarse-grained molecular dynamics simulations to elucidate the distribution and conformation of organic surface ligands, highlighting their influence on PQD packing. Notably, the mixing of two PQDs of different sizes promotes closer face-to-face contact. The densely packed binary-disperse film exhibited largely suppressed trap-assisted recombination, much longer carrier lifetime, and thereby improved power conversion efficiency. Hence, this study provides fundamental understanding of the packing mechanism of perovskite quantum dots and highlights the significance of packing density for PQD-based solar cells.

Interface Modification for Energy Level Alignment and Charge Extraction in CsPbI3 Perovskite Solar Cells

In perovskite solar cells (PSCs) energy level alignment and charge extraction at the interfaces are the essential factors directly affecting the device performance. In this work, we present a modified interface between all-inorganic CsPbI3 perovskite and its hole-selective contact (spiro-OMeTAD), realized by the dipole molecule trioctylphosphine oxide (TOPO), to align the energy levels. On a passivated perovskite film, with n-octylammonium iodide (OAI), we created an upward surface band-bending at the interface by TOPO treatment. This improved interface by the dipole molecule induces a better energy level alignment and enhances the charge extraction of holes from the perovskite layer to the hole transport material. Consequently, a Voc of 1.2 V and a high-power conversion efficiency (PCE) of over 19% were achieved for inorganic CsPbI3 perovskite solar cells. Further, to demonstrate the effect of the TOPO dipole molecule, we present a layer-by-layer charge extraction study by a transient surface photovoltage (trSPV) technique accomplished by a charge transport simulation.

Octahedral Distortions Generate a Thermally Activated Phonon-Assisted Radiative Recombination Pathway in Cubic CsPbBr3 Perovskite Quantum Dots

Exciton-phonon interactions elucidate structure-function relationships that aid in the control of color purity and carrier diffusion, which is necessary for the performance-driven design of solid-state optical emitters. Temperature-dependent steady-state photoluminescence (PL) and time-resolved PL (TRPL) reveal that thermally activated exciton-phonon interactions originate from structural distortions related to vibrations in cubic CsPbBr3 perovskite quantum dots (PQDs) at room temperature. Exciton-phonon interactions cause performance-degrading PL line width broadening and slower electron-hole recombination. Structural distortions in cubic PQDs at room temperature exist as the bending and stretching of the PbBr6 octahedra subunit. The PbBr6 octahedral distortions cause symmetry breaking, resulting in thermally activated longitudinal optical (LO) phonon coupling to the photoexcited electron-hole pair that manifests as inhomogeneous PL line width broadening. At cryogenic temperatures, the line width broadening is minimized due to a decrease in phonon-assisted recombination through shallow traps. A fundamental understanding of these intrinsic exciton-phonon interactions gives insight into the polymorphic nature of the cubic phase and the origins of performance degradation in PQD optical emitters.

Synthesis of CsPbBr3 in Micro Total Reaction System: Fast Operation Space Mapping and Subsecond Growth Process Monitoring

Lead halide perovskite nanocrystals (LHP NCs) have the characteristics of fast reaction kinetics and crystal instability due to the intrinsically highly ionic bonding between the respective ions, which bring challenges for revealing the growth kinetics and practical applications. Compared with conventional batch synthesis methods, the single-function microreactor can achieve precise and stable control of the NCs synthesis process, but it still has the shortcoming of not being able to obtain information about the growth process. In this study, a micro Total Reaction System (μTRS) with remote control, online detection, and rapid data analysis functions is designed. μTRS can sample the photoluminescence information of CsPbBr3 NCs growth in ligand-assisted reprecipitation method. CsPbBr3 NCs with an emission range of 435-492 nm are successfully detected, which breaks the record of the smallest size of CsPbBr3 NCs synthesized directly from precursors. The real-time feature of μTRS enables the construction of an automated close-loop synthesis system. Besides, the rapid acquisition and timely processing of product information enable the rapid mapping of the operation space for CsPbBr3 NCs preparation, which provides a reliable and learnable data set for designing a fully autonomous microreaction system capable of synthesizing NCs.

Introduction to halide perovskite optoelectronics

An introduction to the Nanoscale themed collection on halide perovskite nanomaterials for optoelectronic applications, featuring a variety of articles that highlight the latest developments to address ongoing challenges in the field.

First-Principles Investigation of Novel Alkali-Based Lead-Free Halide Perovskites for Advanced Optoelectronic Applications

Lead-free halide perovskites are considered promising candidates as visible light absorbers with outstanding optoelectronic properties. In this work, novel kinds of lead-free halide perovskites were studied for their electronic, optical, and thermoelectric properties by employing the most precise and enhanced modified Trans-Blaha Beck-Johnson potential. The estimated band spectra of the studied materials were comparable. The materials are confirmed to have an indirect band gap semiconducting nature due to the existence of energy band gaps. Among the studied materials, CsSnI3 has a smaller band gap, confirming the excitation to be more energy efficient. Examining the predicted density of states and true electronic orbital contributions, we observed a progressive fluctuation along the energy axis was observed. Furthermore, the linear optical properties are calculated and studied in terms of possible optoelectronic applications. The absorption in KSnI3 was greater compared to the other two materials. The studied materials could be used for antireflecting coatings against UV radiation, owing to the prominent peaks in their reflectivity spectra. The Seebeck coefficient and electrical properties, as well as the positive value of RH all pointed to a p-type nature in these materials. From the anticipated thermoelectric properties, the materials also appear to be suitable for application in thermoelectric devices.

Colloidal semiconductor nanocrystals: from bottom-up nanoarchitectonics to energy harvesting applications

Colloidal semiconductor nanocrystals (NCs) have been extensively investigated owing to their unique properties induced by the quantum confinement effect. The advent of colloidal synthesis routes led to the design of stable colloidal NCs with uniform size, shape, and composition. Metal oxides, phosphides, and chalcogenides (ZnE, CdE, PbE, where E = S, Se, or Te) are few of the most important monocomponent semiconductor NCs, which show excellent optoelectronic properties. The ability to build quantum confined heterostructures comprising two or more semiconductor NCs offer greater customization and tunability of properties compared to their monocomponent counterparts. More recently, the halide perovskite NCs showed exceptional optoelectronic properties for energy generation and harvesting applications. Numerous applications including photovoltaic, photodetectors, light emitting devices, catalysis, photochemical devices, and solar driven fuel cells have demonstrated using these NCs in the recent past. Overall, semiconductor NCs prepared via the colloidal synthesis route offer immense potential to become an alternative to the presently available device applications. This feature article will explore the progress of NCs syntheses with outstanding potential to control the shape and spatial dimensionality required for photovoltaic, light emitting diode, and photocatalytic applications. We also attempt to address the challenges associated with achieving high efficiency devices with the NCs and possible solutions including interface engineering, packing control, encapsulation chemistry, and device architecture engineering.

Enrichment of anchoring sites by introducing supramolecular halogen bonds for the efficient perovskite nanocrystal LEDs

Considering the multi-functionalization of ligands, it is crucial for ligand molecular design to reveal the landscape of anchoring sites. Here, a typical triphenylphosphine (TPP) ligand was employed to explore its effect on the surface of CsPbI3 perovskite nanocrystals (PNCs). Except for the conventionally considered P-Pb coordination, an P-I supramolecular halogen bonding was also found on the NC surface. The coexistence of the above two types of bonding significantly increased the formation energy of iodine vacancy defects and improved the photoluminescence quantum yield of PNCs up to 93%. Meanwhile, the direct interaction of P and I enhanced the stability of the Pb-I octahedra and dramatically inhibited the migration of I ions. Furthermore, the introduction of additional benzene rings (2-(Diphenylphosphino)-biphenyl (DPB)) increased the delocalized properties of the PNC surface and significantly improved the charge transport of the PNCs. As a result, the DPB passivated CsPbI3 NCs based top-emitting LEDs exhibite a peak external quantum efficiency (EQE) of 22.8%, a maximum luminance of 15, 204 cd m-2, and an extremely low-efficiency roll-off of 2.6% at the current density of 500 mA cm-2.

Optical Memory, Switching, and Neuromorphic Functionality in Metal Halide Perovskite Materials and Devices

Metal halide perovskite based materials have emerged over the past few decades as remarkable solution-processable optoelectronic materials with many intriguing properties and potential applications. These emerging materials have recently been considered for their promise in low-energy memory and information processing applications. In particular, their large optical cross-sections, high photoconductance contrast, large carrier-diffusion lengths, and mixed electronic/ionic transport mechanisms are attractive for enabling memory elements and neuromorphic devices that are written and/or read in the optical domain. Here, recent progress toward memory and neuromorphic functionality in metal halide perovskite materials and devices where photons are used as a critical degree of freedom for switching, memory, and neuromorphic functionality is reviewed.

Ligand-Assisted Self-Assembly of 3D Perovskite Nanocrystals into Chiral Inorganic Quasi-2D Perovskites (n = 3) with Ligand-Ratio-Dependent Chirality Inversion

Chiral inorganic quasi-2D perovskites are prepared by self-assembling 3D perovskites in solution for the first time. The quasi-2D perovskite synthesized is a pure-phase perovskite with = 3 and is periodically arranged, which is a big breakthrough in quasi-2D inorganic perovskites.  With the individual chiral CsPbBr3 nanocrystals (NCs) assemble into quasi-2D perovskite, the g-factor significantly improved (≈5 × 10-3 ). In addition, the chiroptical activity of quasi-2D perovskites is explored to be improved with the lateral size increasing. In the first stage of assembly, chiral optical activity is increased due to the lateral size-dependent optical activity, while the changes in the later stages are attributable to the chiral morphology. Interestingly, chirality inversion is found to be correlated to the number of ligands. It is believed that different conformers of chiral ligands caused by steric hindrance of the original ligand oleylamine result in opposite circular dichroism (CD) polarities. The chirality inversion phenomenon is universal, regardless of the choice of ligands. This work opens up a new path for the synthesis of quasi-2D perovskites and provides more opportunities for the modulation of chiral optical activity.

Enhanced Hot-Phonon Bottleneck Effect on Slowing Hot Carrier Cooling in Metal Halide Perovskite Quantum Dots with Alloyed A-Site

A deep understanding of the effect of the A-site cation cross-exchange on the hot-carrier relaxation dynamics in perovskite quantum dots (PQDs) has profound implications on the further development of disruptive photovoltaic technologies. In this study, the hot carrier cooling kinetics of pure FAPbI3 (FA+ , CH(NH2 )2 + ), MAPbI3 (MA+ , CH3 NH3 + + ), CsPbI3 (Cs+ , Cesium) and alloyed FA0.5 MA0.5 PbI3 , FA0.5 Cs0.5 PbI3 , and MA0.5 Cs0.5 PbI3 QDs are investigated using ultrafast transient absorption (TA) spectroscopy. The lifetimes of the initial fast cooling stage (<1 ps) of all the organic cation-containing PQDs are shorter than those of the CsPbI3 QDs, as verified by the electron-phonon coupling strength extracted from the temperature-dependent photoluminescence spectra. The lifetimes of the slow cooling stage of the alloyed PQDs are longer under illumination greater than 1 sun, which is ascribed to the introduction of co-vibrational optical phonon modes in the alloyed PQDs. This facilitated efficient acoustic phonon upconversion and enhanced the hot-phonon bottleneck effect, as demonstrated by first-principles calculations.

Structural Features and Optical Properties of All-Inorganic Zero-Dimensional Halides Cs4PbBr6-xIx Obtained by Mechanochemistry

Despite the great success of hybrid CH3NH3PbI3 perovskite in photovoltaics, ascribed to its excellent optical absorption properties, its instability toward moisture is still an insurmountable drawback. All-inorganic perovskites are much less sensitive to humidity and have potential interest for solar cell applications. Alternative strategies have been developed to design novel materials with appealing properties, which include different topologies for the octahedral arrangements from three-dimensional (3D, e.g., CsPbBr3 perovskite) or two-dimensional (2D, e.g., CsPb2Br5) to zero-dimensional (0D, i.e., without connection between octahedra), as the case of Cs4PbX6 (X = Br, I) halides. The crystal structure of these materials is complex, and their thermal evolution is unexplored. In this work, we describe the synthesis of Cs4PbBr6-xIx (x = 0, 2, 4, 6) halides by mechanochemical procedures with green credentials; these specimens display excellent crystallinity enabling a detailed structural investigation from synchrotron X-ray powder diffraction (SXRD) data, essential to revisit some features in the temperature range of 90-298 K. In all this regime, the structure is defined in the trigonal R3̅c space group (#167). The presence of Cs and X vacancies suggests some ionic mobility into the crystal structure of these 0D halides. Bond valence maps (BVMs) are useful in determining isovalent surfaces for both Cs4PbBr6 and Cs4PbI6 phases, unveiling the likely ionic pathways for cesium and bromide ions and showing a full 3D connection in the bromide phase, in contrast to the iodide one. On the other hand, the evolution of the anisotropic displacement parameters is useful to evaluate the Debye temperatures, confirming that Cs atoms have more freedom to move, while Pb is more confined at its site, likely due to a higher covalency degree in Pb-X bonds than that in Cs-X bonds. Diffuse reflectance ultraviolet-visible (UV-vis) spectroscopy shows that the optical band gap can be tuned depending on iodine content (x) in the range of 3.6-3.06 eV. From density functional theory (DFT) simulations, the general trend of reducing the band gap when Br is replaced by I is well reproduced.

Recent progress in the stabilization of low band-gap black-phase iodide perovskite solar cells

All-inorganic and organic-inorganic hybrid perovskite solar cells (PSCs) have taken a quantum leap owing to their high performance and low-cost solution processability. Their efficiency has been dramatically increased up to ∼26%, matching the conventional inorganic photovoltaics like monocrystalline Si (26.1%), polycrystalline Si (21.6%), CdTe (22.1%), and CIGS (22.3%). Such outstanding performance has been achieved due to their excellent optoelectronic properties, such as a direct bandgap in the visible region, a very high absorption coefficient, a long charge-carrier diffusion length, and ambipolar carrier transport characteristics. FAPbI3 (FA = formamidinium) and CsPbI3 perovskites among the pool of perovskites are recommended for solar cell applications because they meet all the requirements for photovoltaic applications. However, the fundamental problem of these perovskites is that their photoactive black phase is highly unstable under ambient conditions due to small and large sizes of Cs+ and FA+ ions, respectively. The instability of the black phase of these perovskites hinders their applications in photovoltaic devices as a high-quality light absorber layer. Several approaches have been employed to prevent the formation of the photo-inactive yellow phase or to enhance the stability of the black phase of perovskites, such as dimensional and compositional engineering, the addition of external additives, and dimensional engineering. This perspective summarizes the various methods for stabilizing the black phase of CsPbI3 and FAPbI3 perovskites at room temperature as well as their application in photovoltaic devices.

Effective Suppressing Phase Segregation of Mixed-Halide Perovskite by Glassy Metal-Organic Frameworks

Lead mixed-halide perovskites offer tunable bandgaps for optoelectronic applications, but illumination-induced phase segregation can quickly lead to changes in their crystal structure, bandgaps, and optoelectronic properties, especially for the Br-I mixed system because CsPbI3 tends to form a non-perovskite phase under ambient conditions. These behaviors can impact their performance in practical applications. By embedding such mixed-halide perovskites in a glassy metal-organic framework, a family of stable nanocomposites with tunable emission is created. Combining cathodoluminescence with elemental mapping under a transmission electron microscope, this research identifies a direct relationship between the halide composition and emission energy at the nanoscale. The composite effectively inhibits halide ion migration, and consequently, phase segregation even under high-energy illumination. The detailed mechanism, studied using a combination of spectroscopic characterizations and theoretical modeling, shows that the interfacial binding, instead of the nanoconfinement effect, is the main contributor to the inhibition of phase segregation. These findings pave the way to suppress the phase segregation in mixed-halide perovskites toward stable and high-performance optoelectronics.

Surface polarization-induced emission and stability enhancement of CsPbX3 nanocrystals

Recently, the polarization effect has been receiving tremendous attention, as it can result in improved stability and charge transfer efficiency of metal-halide perovskites (MHPs). However, realizing the polarization effect on CsPbX3 NCs still remains a challenge. Here, metal ions with small radii (such as Mg2+, Li+, Ni2+, etc.) are introduced on the surface of CsPbX3 NCs, which facilitate the arising of electric dipole and surface polarization. The surface polarization effect promotes redistribution of the surface electron density, leading to reinforced surface ligand bonding, reduced surface defects, near unity photoluminescence quantum yields (PLQYs), and enhanced stability. Moreover, further introduction of hydroiodic acid results in the in situ formation of tert-butyl iodide (TBI), which facilitates the successful synthesis of pure iodine-based CsPbI3 NCs with high PLQY (95.3%) and stability under ambient conditions. The results of this work provide sufficient evidence to exhibit the crucial role of the surface polarization effect, which promotes the synthesis of high-quality MHPs and their applications in the fields of optoelectronic devices.

Synergistic Halide- and Ligand-Exchanges of All-Inorganic Perovskite Nanocrystals for Near-Unity and Spectrally Stable Red Emission

All-inorganic perovskite nanocrystals (NCs) of CsPbX3 (X = Cl, Br, I) are promising for displays due to wide color gamut, narrow emission bandwidth, and high photoluminescence quantum yield (PLQY). However, pure red perovskite NCs prepared by mixing halide ions often result in defects and spectral instabilities. We demonstrate a method to prepare stable pure red emission and high-PLQY-mixed-halide perovskite NCs through simultaneous halide-exchange and ligand-exchange. CsPbBr3 NCs with surface organic ligands are first synthesized using the ligand-assisted reprecipitation (LARP) method, and then ZnI2 is introduced for anion exchange to transform CsPbBr3 to CsPbBrxI3-x NCs. ZnI2 not only provides iodine ions but also acts as an inorganic ligand to passivate surface defects and prevent ion migration, suppressing non-radiative losses and halide segregation. The luminescence properties of CsPbBrxI3-x NCs depend on the ZnI2 content. By regulating the ZnI2 exchange process, red CsPbBrxI3-x NCs with organic/inorganic hybrid ligands achieve near-unity PLQY with a stable emission peak at 640 nm. The CsPbBrxI3-x NCs can be combined with green CsPbBr3 NCs to construct white light-emitting diodes with high-color gamut. Our work presents a facile ion exchange strategy for preparing spectrally stable mixed-halide perovskite NCs with high PLQY, approaching the efficiency limit for display or lighting applications.

Synthesis of Layered Lead-Free Perovskite Nanocrystals with Precise Size and Shape Control and Their Photocatalytic Activity

Halide perovskites have attracted enormous attention due to their potential applications in optoelectronics and photocatalysis. However, concerns over their instability, toxicity, and unsatisfactory efficiency have necessitated the development of lead-free all-inorganic halide perovskites. A major challenge in designing efficient halide perovskites for practical applications is the lack of effective methods for producing nanocrystals with precise size and shape control. In this work, a layered perovskite, Cs4ZnSb2Cl12 (CZS), is found from calculations to exhibit size- and facet-dependent optoelectronic properties in the nanoscale, and thus, a colloidal method is used to synthesize the CZS nanoparticles with size-tunable morphologies: zero- (nanodots), one- (nanowires and nanorods), two- (nanoplates), and three-dimensional (nanopolyhedra). The growth kinetics of the CZS nanostructures, along with the effects of surface ligands, reaction temperature, and time were investigated. The optoelectronic properties of the nanocrystals varied with size due to quantum confinement effects and with shape due to anisotropy within the crystals and the exposure of specific facets. These properties could be modulated to enhance the visible-light photocatalytic performance for toluene oxidation. In particular, the 9.7 nm CZS nanoplates displayed a toluene to benzaldehyde conversion rate of 1893 μmol g-1 h-1 (95% selectivity), 500 times higher than the bulk synthesized CZS, and comparable with the reported photocatalysts. This study demonstrates the integration of theoretical calculations and synthesis, revealing an approach to the design and fabrication of novel, high-performance colloidal perovskite nanocrystals for optoelectronic and photocatalytic applications.

Stabilized Perovskite Quantum Dot Solids via Nonpolar Solvent Dispersible Covalent Ligands

The ligand exchange procedure of CsPbI3 perovskite quantum dots (PQDs) enables the fabrication of thick and conductive PQD solids that act as a photovoltaic absorber for solution-processed thin-film solar cells. However, the ligand-exchanged CsPbI3 PQD solids suffer from deterioration in photovoltaic performance and ambient stability due to the surface traps, such as uncoordinated Pb2+ sites on the PQD surface, which are generated after the conventional ligand exchange process using ionic short-chain ligands dissolved in polar solvents. Herein, a facile surface stabilization is demonstrated that can simultaneously improve the photovoltaic performance and ambient stability of CsPbI3 PQD photovoltaic absorber using covalent short-chain triphenylphosphine oxide (TPPO) ligands dissolved in a nonpolar solvent. It is found that the TPPO ligand can be covalently bound to uncoordinated Pb2+ sites and the nonpolar solvent octane can completely preserve the PQD surface components. Owing to their synergetic effects, the CsPbI3 PQD photovoltaic absorber stabilized using the TPPO ligand solution dissolved in octane exhibit higher optoelectrical properties and ambient stability than the control absorber. Consequently, CsPbI3 PQD solar cells composed of PQD photovoltaic absorbers fabricated via surface stabilization strategy provide an improved power conversion efficiency of 15.4% and an enhanced device stability.

High-Resolution, Highly Transparent, and Efficient Quantum Dot Light-Emitting Diodes

Aiming at next-generation displays, high-resolution quantum dot light-emitting diodes (QLEDs) with high efficiency and transparency are highly desired. However, there is limited study involving the improvements of QLED pixel resolution, efficiency, and transparency simultaneously, which undoubtedly restricts the practical applications of QLED for next-generation displays. Here, the strategy of electrostatic force-induced deposition (EF-ID) is proposed by introducing alternating polyethyleneimine (PEI) and fluorosilane patterns to synergistically improve the pixel accuracy and transmittance of QD patterns. More importantly, the leakage current induced by the void spaces between pixels that is usually reported for high-resolution QLEDs is greatly suppressed by substrate-assisted insulating fluorosilane patterns. Finally, high-performance QLEDs with high resolution ranging from 1104 to 3031 pixels per inch (PPI) and a high efficiency of 15.6% are achieved, among the best performances of high resolution QLEDs. Notably, the high resolution QD pixels greatly enhance the transmittance of the QD patterns, thus prompting an impressive transmittance of 90.7% for the transparent QLEDs (2116 PPI), which represents the highest transmittance of transparent QLED devices. Consequently, this work contributes an effective and general approach for high-resolution QLEDs with high efficiency and transparency.

High Quality Factor in Solution-Processed Inorganic Microcavities Embedding CsPbBr3 Perovskite Nanocrystals

Optical microcavities grant manipulation over light-matter interactions and light propagation, enabling the fabrication of foundational optical and optoelectronic components. However, the materials used for high-performing systems, mostly bulk inorganics, are typically costly, and their processing is hardly scalable. In this work, we present an alternative way to fabricate planar optical resonators via solely solution processing while approaching the performances of conventional systems. Here, we couple fully solution-processed high dielectric contrast inorganic Bragg mirrors obtained by sol-gel deposition with the remarkable photoluminescence properties of CsPbBr3 perovskite nanocrystals. The approach yields microcavities with a quality factor of ∼220, which is a record value for solution-processed inorganic structures, and a strong emission redistribution resulting in a 3-fold directional intensity enhancement.

Mechanical Stability and Energy Gap Evolution in Cs-Based Ag, Bi Halide Double Perovskites under High Pressure: A Theoretical DFT Approach

Due to their intrinsic stability and reduced toxicity, lead-free halide double perovskite semiconductors have become potential alternatives to lead-based perovskites. In the present study, we used density functional theory simulations to investigate the mechanical stability and band gap evolution of double perovskites Cs₂AgBiX₆ (X = Cl and Br) under an applied pressure. To investigate the pressure-dependent properties, the hydrostatic pressure induced was in the range of 0-100 GPa. The mechanical behaviors indicated that the materials under study are both ductile and mechanically stable and that the induced pressure enhances the ductility. As a result of the induced pressure, the covalent bonds transformed into metallic bonds with a reduction in bond lengths. Electronic properties, energy bands, and electronic density of states were obtained with the hybrid HSE06 functional, including spin-orbit coupling (HSE06 + SOC) calculations. The electronic structure study revealed that Cs₂AgBiX₆ samples behave as X-Γ indirect gap semiconductors, and the gap reduces with the applied pressure. The pressure-driven samples ultimately transform from the semiconductor to a metallic phase at the given pressure range. Also, the calculations demonstrated that the applied pressure and spin-orbit coupling of the states pushed VBM and CBM toward the Fermi level which caused the evolution of the band gap. The relationship between the structure and band gap demonstrates the potential for designing lead-free inorganic perovskites for optoelectronic applications, including solar cells as well as X-ray detectors.

Ultrapure Green High Photoluminescence Quantum Yield from FAPbBr3 Nanocrystals Embedded in Transparent Porous Films

Achieving highly transparent and emissive films based on perovskite quantum dots (PQDs) is a challenging task since their photoluminescence quantum yield (PLQY) typically drops abruptly when they are used as building blocks to make a solid. In this work, we obtain highly transparent films containing FAPbBr₃ quantum dots that display a narrow green emission (λ = 530 nm, full width at half-maximum (FWHM) = 23 nm) with a PLQY as high as 86%. The method employed makes use of porous matrices that act as arrays of nanoreactors to synthesize the targeted quantum dots within their void space, providing both a means to keep them dispersed and a protective environment. Further infiltration with poly(methyl methacrylate) (PMMA) increases the mechanical and chemical stability of the ensemble and serves to passivate surface defects, boosting the emission of the embedded PQD and significantly reducing the width of the emission peak, which fulfills the requirements established by the Commission Internationale de l'Éclairage (CIE) to be considered an ultrapure green emitter. The versatility of this approach is demonstrated by fabricating a color-converting layer that can be easily transferred onto a light-emitting device surface to modify the spectral properties of the outgoing radiation.

In Situ Iodide Passivation Toward Efficient CsPbI3 Perovskite Quantum Dot Solar Cells

Highlights

The introduction of hydroiodic acid (HI) manipulates the dynamic conversion of PbI2 into highly coordinated species to optimize the nucleation and growth kinetics. The addition of HI enables the fabrication of CsPbI3 perovskite quantum dots with reduced defect density, enhanced crystallinity, higher phase purity, and near-unity photoluminescence quantum yield. The efficiency of CsPbI3 perovskite quantum dot solar cells was enhanced from 14.07% to 15.72% together with enhanced storage stability.

Abstract

All-inorganic CsPbI3 quantum dots (QDs) have demonstrated promising potential in photovoltaic (PV) applications. However, these colloidal perovskites are vulnerable to the deterioration of surface trap states, leading to a degradation in efficiency and stability. To address these issues, a facile yet effective strategy of introducing hydroiodic acid (HI) into the synthesis procedure is established to achieve high-quality QDs and devices. Through an in-depth experimental analysis, the introduction of HI was found to convert PbI2 into highly coordinated [PbIm]2−m, enabling control of the nucleation numbers and growth kinetics. Combined optical and structural investigations illustrate that such a synthesis technique is beneficial for achieving enhanced crystallinity and a reduced density of crystallographic defects. Finally, the effect of HI is further reflected on the PV performance. The optimal device demonstrated a significantly improved power conversion efficiency of 15.72% along with enhanced storage stability. This technique illuminates a novel and simple methodology to regulate the formed species during synthesis, shedding light on further understanding solar cell performance, and aiding the design of future novel synthesis protocols for high-performance optoelectronic devices.

Supplementary Information

The online version contains supplementary material available at 10.1007/s40820-023-01134-1.

Design Rules for Obtaining Narrow Luminescence from Semiconductors Made in Solution

Solution-processed semiconductors are in demand for present and next-generation optoelectronic technologies ranging from displays to quantum light sources because of their scalability and ease of integration into devices with diverse form factors. One of the central requirements for semiconductors used in these applications is a narrow photoluminescence (PL) line width. Narrow emission line widths are needed to ensure both color and single-photon purity, raising the question of what design rules are needed to obtain narrow emission from semiconductors made in solution. In this review, we first examine the requirements for colloidal emitters for a variety of applications including light-emitting diodes, photodetectors, lasers, and quantum information science. Next, we will delve into the sources of spectral broadening, including "homogeneous" broadening from dynamical broadening mechanisms in single-particle spectra, heterogeneous broadening from static structural differences in ensemble spectra, and spectral diffusion. Then, we compare the current state of the art in terms of emission line width for a variety of colloidal materials including II-VI quantum dots (QDs) and nanoplatelets, III-V QDs, alloyed QDs, metal-halide perovskites including nanocrystals and 2D structures, doped nanocrystals, and, finally, as a point of comparison, organic molecules. We end with some conclusions and connections, including an outline of promising paths forward.

Review of nanomaterial advances for ionizing radiation dosimetry

There are a wide range of applications with ionizing radiation and a common theme throughout these is that accurate dosimetry is usually required, although many newer demands are provided by improved features in higher range, multi-spectral and particle type detected. Today, the array of dosimeters includes both offline and online tools, such as gel dosimeters, thermoluminescence (TL), scintillators, optically stimulated luminescence (OSL), radiochromic polymeric films, gels, ionization chambers, colorimetry, and electron spin resonance (ESR) measurement systems. Several future nanocomposite features and interpretation of their substantial behaviors are discussed that can lead to improvements in specific features, such as (1) lower sensitivity range, (2) less saturation at high range, (3) overall increased dynamic range, (4) superior linearity, (5) linear energy transfer and energy independence, (6) lower cost, (7) higher ease of use, and (8) improved tissue equivalence. Nanophase versions of TL and ESR dosimeters and scintillators each have potential for higher range of linearity, sometimes due to superior charge transfer to the trapping center. Both OSL and ESR detection of nanomaterials can have increased dose sensitivity because of their higher readout sensitivity with nanoscale sensing. New nanocrystalline scintillators, such as perovskite, have fundamentally important advantages in sensitivity and purposeful design for key new applications. Nanoparticle plasmon coupled sensors doped within a lower Zeff material have been an effective way to achieve enhanced sensitivity of many dosimetry systems while still achieving tissue equivalency. These nanomaterial processing techniques and unique combinations of them are key steps that lead to the advanced features. Each must be realized through industrial production and quality control with packaging into dosimetry systems that maximize stability and reproducibility. Ultimately, recommendations for future work in this field of radiation dosimetry were summarized throughout the review.

Study on myocardial toxicity induced by lead halide perovskites nanoparticles

Lead halide perovskites (LHPs) are outstanding candidates for next-generation optoelectronic materials, with considerable prospects of use and commercial value. However, knowledge about their toxicity is scarce, which may limit their commercialization. Here, for the first time, we studied the cardiotoxicity and molecular mechanisms of representative CsPbBr3 nanoparticles in LHPs. After their intranasal administration to Institute of Cancer Research (ICR) mice, using advanced synchrotron radiation, mass spectrometry, and ultrasound imaging, we revealed that CsPbBr3 nanoparticles can severely affect cardiac systolic function by accumulating in the myocardial tissue. RNA sequencing and Western blotting demonstrated that CsPbBr3 nanoparticles induced excessive oxidative stress in cardiomyocytes, thereby provoking endoplasmic reticulum stress, disturbing calcium homeostasis, and ultimately leading to apoptosis. Our findings highlight the cardiotoxic effects of LHPs and provide crucial toxicological data for the product.

Size-Dependent Lattice Symmetry Breaking Determines the Exciton Fine Structure of Perovskite Nanocrystals

The order of bright and dark excitonic states in lead-halide perovskite nanocrystals is debated. It has been proposed that the Rashba effect, driven by lattice-induced symmetry breaking, causes a bright excitonic ground state. Direct measurements of excitonic spectra, however, show the signatures of a dark ground state, bringing the role of the Rashba effect into question. We use an atomistic theory to model the exciton fine structure of perovskite nanocrystals, accounting for realistic lattice distortions. We calculate optical gaps and excitonic features that compare favorably with experimental works. The exciton fine structure splittings show a nonmonotonic size dependence due to a structural transition between cubic and orthorhombic phases. Additionally, the excitonic ground state is found to be dark with spin triplet character, exhibiting a small Rashba coupling. We additionally explore the effects of nanocrystal shape on the fine structure, clarifying observations on polydisperse nanocrystals.

Highly Stable and Efficient Light-Emitting Diodes Based on Orthorhombic γ-CsPbI3 Nanocrystals

Orthorhombic γ-CsPbI₃ possesses the highest structural stability among the optically active (light-emissive) CsPbI₃ perovskites. Here, we make use of a seed-assisted heteroepitaxial growth to fabricate seed/core/shell CaI_x/γ-CsPbI₃/CaI₂ nanocrystals. Ultrasmall CaI_x nanoparticles serve as seeds to template the Pb-centered octahedral arrangement which enables the formation of the γ-CsPbI₃ phase and at the same time inhibit lattice strain by blocking the force transfer that otherwise leads to an octahedral twist and so improve the structural stability of the resulting nanocrystals. An outer shell composed from the same material, CaI₂, isolates the formed γ-CsPbI₃ nanocrystals from the environment, which also significantly improves their stability under ambient conditions. Optical and electrical studies indicate that the seed/core/shell CaI_x/γ-CsPbI₃/CaI₂ structure possesses a shallower set of trap states as compared to cubic α-CsPbI₃ nanocrystals. Light-emitting diodes utilizing these γ-CsPbI₃ nanocrystals show a record high external quantum efficiency of 25.3%, high brightness of over 13600 cd/m², and an operational lifetime of ∼14 h before reaching 50% of their initial luminance. These devices can repeatedly be illuminated over 650 times at ∼500 cd/m² with no decline of brightness, which indicates their great commercial potential.

Whispering gallery mode micro-lasing in CsPbI3 quantum dots coated on TiO2 microspherical resonating cavities

Whispering gallery mode (WGM) lasing in CsPbI₃ quantum dots (QDs) coated on TiO₂ spherical microcavities is demonstrated. The photoluminescence emission from a CsPbI₃-QDs gain medium strongly couples with a TiO₂ microspherical resonating optical cavity. Spontaneous emission in these microcavities switches to a stimulated emission above a distinct threshold point of 708.7 W/cm². Lasing intensity increases three to four times as the power density increases by one order of magnitude beyond the threshold point when the microcavities are excited with a 632-nm laser. WGM microlasing with quality factors as high as Q∼1195 is demonstrated at room temperature. Quality factors are found to be higher for smaller TiO₂ microcavities (∼2 µm). CsPbI₃-QDs/TiO₂ microcavities are also found to be photostable even after continuous laser excitation for 75 minutes. The CsPbI₃-QDs/TiO₂ microspheres are promising as WGM-based tunable microlasers.

Engineering CsPbX3 (X = Cl, Br, I) Quantum Dot-Embedded Borosilicate Glass through Self-Crystallization Facilitated by NaF as a Phosphor for Full-Color Illumination and Laser-Driven Projection Displays

All inorganic perovskite (CsPbX₃, X = Cl, Br, I) quantum dot (QD) glass samples are considered the next generation of lighting materials for their excellent luminescence properties and stability, but crystallization conditions are difficult to control, which often leads to the inhomogeneous crystallinity of QDs. Here, we provided evidence that the presence of sodium fluoride induced self-crystallization of CsPbBr₃ QDs during routine glass formation without the need for additional heat treatment. We showed that NaF simultaneously affected the network structure of glass and promoted the formation of CsPbBr₃ QDs, that is, Na⁺ ions entered the glass network skeleton, partially interrupting the network structure, while the strong electronegativity of F^- ions attracted Cs⁺ and Pb²⁺ ions into the gaps formed in the glass networks that had been loosened up by Na⁺ ions, which reduced the activation energy of crystallization processes. Our results showed that NaF-induced CsPbBr₃ QDs glass had excellent thermal stability, high photoluminescence quantum efficiency (49%), and luminescent stability under high-power laser irradiation. Finally, this work also demonstrated the general applicability of this method in the making of a series of CsPbX₃ (X = Cl, Br, I) QD glass samples by NaF-induced self-crystallization, which drastically expanded the color gamut to a range of full spectrum for luminescence and laser-driven projection displays. We believe that the work presented here represents a new direction for the research and development of full-color gamut inorganic perovskite quantum dot glass samples, which could have a significant impact on the future applications of laser-driven projection displays as well.

Potential of AMnO3 (A=Ca, Sr, Ba, La) as Active Layer in Inorganic Perovskite Solar Cells

Inorganic perovskite CaMnO3 ${{}_{3}}$ was proposed as a substitution for the TiO2 ${{}_{2}}$ anatase in electron transport layers of solar cells containing the hybrid perovskite CH3 ${{}_{3}}$ NH3 ${{}_{3}}$ PbI3 ${{}_{3}}$ based on increased mobility of electrons and better optical matching. Due to a suitable band gap concerning the absorption of sunlight, we investigate the potential of CaMnO3 ${{}_{3}}$ and similar manganite perovskites, where Ca is replaced by either Sr, Ba or La, as an absorber layer in inorganic perovskite solar cells. In this study, we have used optical measurements on the synthesized AMnO3 ${{}_{3}}$ (A=Ca, Sr, Ba, La) samples to aid density functional theory calculations (DFT) in order to accurately simulate the electronic and optical properties of AMnO3 ${{}_{3}}$ compounds and gauge their potential for the role of absorber layer. Both experimental measurements and theoretical calculations show suitable band gap of 1.1-1.5 eV, depending on the compound, and absorption coefficients of the order of10 5 ${{10}^{5}}$ cm- 1 ${{}^{-1}}$ in the visible part of the spectrum.

Comparing the Cubic and Tetragonal Phases of MAPbI3 at Room Temperature

Stability and maintenance of the crystal structure are the main drawbacks of the application of organic-inorganic perovskites in photovoltaic devices. The ΔT = 62 K robust shift of the structural phase transition observed here allows us to conduct a comprehensive study at room temperature of the tetragonal versus cubic phase on MAPbI₃. The absence of the shift in the cubic transition for all-inorganic CsPbI₃ samples confirms the importance of both orientation and dynamics of the organic cations. Our results provide a unique opportunity to evaluate the physical properties of both cubic and tetragonal phases of MAPbI₃ at the same temperature, eliminating different phonon effects as possible causes for different properties. Besides higher electrical resistivity, the perovskite cubic phase presents a faster charge carrier lifetime than the tetragonal phase and partial PL quenching, pointing toward increased trap-assisted nonradiative recombination. The light absorption coefficient in the cubic phase is larger than the absorption in the tetragonal phase in the green region.

Antisolvent-Assisted In Situ Cation Exchange of Perovskite Quantum Dots for Efficient Solar Cells

Cesium-formamidinium lead iodide perovskite quantum dots (FA_x Cs_{1- x} PbI₃ PQDs) show high potential for next-generation photovoltaics due to their outstanding optoelectronic properties. However, achieving composition-tunable hybrid PQDs with desirable charge transport remains a significant challenge. Herein, by leveraging an antisolvent-assisted in situ cation exchange of PQDs, homogeneous FA_x Cs_{1- x} PbI₃ PQDs with controllable stoichiometries and surface ligand chemistry are realized. Meanwhile, the crystallographic stability of PQDs is substantially improved by substituting the cations of the PQDs mediated by surface vacancies. Consequently, PQD solar cell delivers an efficiency of 17.29%, the highest value among the homostructured PQD solar cells. The high photovoltaic performance is attributed to the broadened light harvesting spectra, flattened energy landscape, and rationalized energy levels of highly oriented PQD solids, leading to efficient charge carrier extraction. This work provides a feasible approach for the stoichiometry regulation of PQDs to finely tailor the optoelectronic properties and tolerance factors of PQDs toward high-performing photovoltaics.

Synchronous Modulation of Energy Level Gradient and Defects for High-Efficiency HTL-Free Carbon-Based All-Inorganic Perovskite Solar Cells

In order to improve the thermal stability of perovskite solar cells (PSCs) and reduce production costs, hole transport layer (HTL)-free carbon-based CsPbI₃ PSCs (C-PSCs) have attracted the attention of researchers. However, the power conversion efficiency (PCE) of HTL-free CsPbI₃ C-PSCs is still lower than that of PSCs with HTL/ metal electrodes. This is because the direct contact between the carbon electrode and the perovskite layer has a higher requirement on the crystal quality of perovskite layer and matched energy level at perovskite/carbon interface. Herein, the acyl chloride group and its derivative trichloroacetyl chloride are used to passivate CsPbI₃ C-PSCs for the first time. The results show that the carbonyl group of trichloroacetyl chloride can effectively passivate the uncoordinated Pb²⁺ ions in perovskite. At the same time, leaving group Cl^- ions can increase the grain size of perovskite and improve the crystallization quality of perovskite layer. In addition, the trichloroacetyl chloride tends to generate cesium chloride acetate, which acts as an electron blocking layer, reduces charge recombination, promotes gradient energy level arrangement, and effectively improves the separation and extraction ability of carriers. The PCE of CsPbI₃ HTL-free C-PSCs is successfully increased from 13.40% to 14.82%.

All-inorganic perovskite solar cells featuring mixed group IVA cations

All-inorganic perovskites are promising for solar cells owing to their potentially superior tolerance to environmental factors, as compared with their hybrid organic-inorganic counterparts. Over the past few years, all-inorganic perovskite solar cells (PSCs) have seen a dramatic improvement in certified power conversion efficiencies (PCEs), demonstrating their great potential for practical applications. Pb, Sn, and Ge are the most studied group IVA elements for perovskites. These group IVA cations share the same number of valence electrons and similarly exhibit the beneficial antibonding properties of lone-pair electrons when incorporated in the perovskite structure. Meanwhile, mixing these cations in all-inorganic perovskites provides opportunities for stabilizing the photoactive phase and tailoring the bandgap structure. In this mini-review, we analyze the structural and bandgap design principles for all-inorganic perovskites featuring mixed group IVA cations, discuss the updated progress in the corresponding PSCs, and finally provide perspectives on future research efforts faciliating the continued development of high-performance Pb-less and Pb-free all-inorganic PSCs.

A and B sites dual substitution by Na+ and Cu2+ co-doping in CsPbBr3 quantum dots to achieve bright and stable blue light emitting diodes

Light-emitting perovskite quantum dots (PeQDs) are extensively investigated owing to their evident merits. However, it is still a challenge to adjust their intrinsic emissions and enhance their thermal stability to achieve full-color highly emissive QD-based light-emitting diodes (QLEDs), especially blue QLEDs. Herein, we demonstrate an effective strategy to fundamentally stabilize the crystal structure of CsPbBr₃ QDs by codoping Na⁺ and Cu²⁺ ions, which are designed to substitute Cs⁺ (A sites) and Pb²⁺ (B sites), respectively. It is found out that the codoping metal ions have significantly improved the thermal stability and the optical properties of the QDs. 40% of the emission intensity can be remained after 8 thermal cycles (20-120 °C) for CsPbBr₃: Na⁺/Cu²⁺ QDs, whilst less than 10% is maintained for undoped CsPbBr₃ QDs. Accordingly, stable blue QLEDs are packed by CsPbBr₃: Na⁺/Cu²⁺ QDs. Strong electroluminescence with the maximum luminance of 7161 cd m^-2 and low turn-on voltage of 2.4 V are realized. The CIE coordinates are tuned from green (0.10, 0.74) to blue (0.17, 0.25) via Na⁺ and Cu²⁺ codoping. The maximum external quantum efficiency (EQE_max) is obtained as 4.52% for PeLEDs based on codoped QDs. The proposed metal ions A and B sites dual substitution strategy guarantees PeQDs as an extremely promising prospect in potential applications as high-resolution displays and high-quality lightings.

Optical anisotropy of CsPbBr3 perovskite nanoplatelets

The two-dimensional CsPbBr3 nanoplatelets have a quantum well electronic structure with a band gap tunable with sample thicknesses in discreet steps based upon the number of monolayers. The polarized optical properties of CsPbBr3 nanoplatelets are studied using fluorescence anisotropy and polarized transient absorption spectroscopies. Polarized spectroscopy shows that they have absorption and emission transitions which are strongly plane-polarized. In particular, photoluminescence excitation and transient absorption measurements reveal a band-edge polarization approaching 0.1, the limit of isotropic two-dimensional ensembles. The degree of anisotropy is found to depend on the thickness of the nanoplatelets: multiple measurements show a progressive decrease in optical anisotropy from 2 to 5 monolayer thick nanoplatelets. In turn, larger cuboidal CsPbBr3 nanocrystals, are found to have consistently positive anisotropy which may be attributed to symmetry breaking from ideal perovskite cubes. Optical measurements of anisotropy are described with respect to the theoretical framework developed to describe exciton fine structure in these materials. The observed planar absorption and emission are close to predicted values at thinner nanoplatelet sizes and follow the predicted trend in anisotropy with thickness, but with larger anisotropy than theoretical predictions. Dominant planar emission, albeit confined to the thinnest nanoplatelets, is a valuable attribute for enhanced efficiency of light-emitting devices.

Tailoring multifunctional anions to inhibit methanol absorption on a CsPbBr3 quantum dot surface for highly efficient semi-transparent photovoltaics

Methyl acetate (MeOAc) is the most used antisolvent in the preparation of perovskite quantum dot (QD) films. However, the hydrolysis of MeOAc results in acetic acid and methanol (MeOH), and the decomposition of the perovskite occurs more easily under acidic and polar conditions. Herein, we report a facile and universal anion modification strategy to inhibit MeOH absorption on a perovskite QD surface and improve the photovoltaic performance of perovskite QD solar cells, which is implemented by incorporating a series of guanidinium salts containing different anions (guanidinium bromide (GuaBr), guanidinium thiocyanate (GuaSCN), and guanidinium acetate (GuaAc)). All anions play a positive role in inhibiting the absorption of MeOH on the QD surface, facilitating charge transfer between perovskite QDs and passivating the defects. Moreover, the regulation of surface chemistry can be optimized by rational tailoring of different anion species. The GuaAc-based devices deliver a PCE of 7.04%, which is the highest value among inorganic CsPbBr₃ QD solar cells. More importantly, the CsPbBr₃ QD solar cells exhibit high transparency over the entire visible spectrum region, indicating their promising application in solar windows.

Thermal tolerance of perovskite quantum dots dependent on A-site cation and surface ligand

A detailed picture of temperature dependent behavior of Cs_xFA_1-xPbI₃ perovskite quantum dots across the composition range is constructed by performing in situ optical spectroscopic and structural measurements, supported by theoretical calculations that focus on the relation between A-site chemical composition and surface ligand binding. The thermal degradation mechanism depends not only on the exact chemical composition, but also on the ligand binding energy. The thermal degradation of Cs-rich perovskite quantum dots is induced by a phase transition from black γ-phase to yellow δ-phase, while FA-rich perovskite quantum dots with higher ligand binding energy directly decompose into PbI₂. Quantum dot growth to form large bulk size grain is observed for all Cs_xFA_1-xPbI₃ perovskite quantum dots at elevated temperatures. In addition, FA-rich quantum dots possess stronger electron-longitudinal optical phonon coupling, suggesting that photogenerated excitons in FA-rich quantum dots have higher probability to be dissociated by phonon scattering compared to Cs-rich quantum dots.

Photoinduced electron transfer across the polymer-capped CsPbBr3 interface in a polar medium

In-situ polymer capping of cesium lead bromide (CsPbBr₃) nanocrystals with polymethyl acrylate is an effective approach to improve the colloidal stability in the polar medium and thus extends their use in photocatalysis. The photoinduced electron transfer properties of polymethyl acrylate (PMA)-capped CsPbBr₃ nanocrystals have been probed using surface-bound viologen molecules with different alkyl chains as electron acceptors. The apparent association constant (K_app) obtained for the binding of viologen molecules with PMA-capped CsPbBr₃ was 2.3 × 10⁷ M^-1, which is an order of magnitude greater than that obtained with oleic acid/oleylamine-capped CsPbBr₃. Although the length of the alkyl chain of the viologen molecule did not show any impact on the electron transfer rate constant, it influenced the charge separation efficiency and net electron transfer quantum yield. Viologen moieties with a shorter alkyl chain length exhibited a charge separation efficiency of 72% compared with 50% for the longer chain alkyl chain length viologens. Implications of polymer-capped CsPbBr₃ perovskite nanocrystals for carrying out photocatalytic reduction in the polar medium are discussed.

Facile Dimension Transformation Strategy for Fabrication of Efficient and Stable CsPbI3 Perovskite Solar Cells

All-inorganic cesium lead triiodide (CsPbI₃) perovskite has received increasing attention due to its intrinsic thermal stability and suitable band gap for photovoltaic applications. However, it is difficult to deposit high-quality pure-phase CsPbI₃ films using CsI and PbI₂ as precursors due to the rapid nucleation and crystal growth by the solution coating method. Here, a simple cation-exchange approach is employed to fabricate all-inorganic 3D CsPbI₃ perovskite, where 1D ethylammonium lead (EAPbI₃) perovskite is first solution-deposited and then transformed to 3D CsPbI₃ via ion exchange between EA⁺ and Cs⁺ during thermal annealing. The large space between the PbI₃^- skeletons in 1D EAPbI₃ favors the cation interdiffusion and exchange for the formation of pure-phase 3D CsPbI₃ with full compactness and high crystallinity and orientation. The resulting CsPbI₃ film exhibits a low trap density of state and high charge mobility, and the perovskite solar cell shows a power-conversion efficiency of 18.2% with enhanced stability. This strategy provides an alternative and promising fabrication route for the fabrication of high-quality all-inorganic perovskite devices.

3D/2D Core/Shell Perovskite Nanocrystals for High-Performance Solar Cells

All-inorganic lead halide perovskite nanocrystals (NCs) emerge as a rising star in photovoltaic fields on account of their excellent optoelectronic properties. However, it still remains challenging to further promote photovoltaic efficiency due to the susceptible surface and inevitable vacancies. Here, this work reports a 3D/2D core/shell perovskite heterojunction based on CsPbI₃ NCs and its performance in solar cells. The guanidinium (GA⁺ ) rich 2D nanoshells can significantly passivate surface trap states and lower the capping ligand density, resulting in improved photoelectric properties and carrier transport and diminished nonradiative recombination centers via the hydrogen bonds from amino groups in GA⁺ ions. Consequently, an outstanding power conversion efficiency (PCE) of up to 15.53% is realized, substantially higher than the control device (13.77%). This work highlights the importance of surface chemistry and offers a feasible avenue to achieve high-performance perovskite NCs-based optoelectronic devices.