Adsorption of emerging contaminants from water and wastewater by modified biochar: A review

Application of biochar immobilized microorganisms for pollutants removal from wastewater: A review

Microbial immobilization technology (MIT) has been rapidly developed and used to remove pollutants from water/wastewater in recent years, owing to its high stability, rapid reaction rate, and high activity. Microbial immobilization carrier with low cost and high removal efficiency is the key of MIT. Biochar is considered to be an efficient carrier for microbial immobilization because of its high porosity and good adsorption effect, which can provide a habitat for microorganisms. The use of biochar immobilized microorganisms to treat different pollutants in wastewater is a promising treatment method. Compared with the other biological treatment technology, biochar immobilized microorganisms can improve microbial abundance, repeated utilization ratio, microbial metabolic capacity, etc. However, current research on this method is still in its infancy. Little attention has been paid to the interaction mechanisms between biochar and microorganisms, and many studies are only carried out in the laboratory. There are still problems such as difficult recovery after use and secondary pollution caused by residual pollutants after biochar adsorption, which need further clarification. To have comprehensive digestion and an in-depth understanding of biochar immobilized microorganisms technology in wastewater treatment, the wastewater treatment methods based on biochar are firstly summarized in this review. Then the mechanisms of immobilized microorganisms were explored, and the applications of biochar immobilized microorganisms in wastewater were systematically reviewed. Finally, suggestions and perspectives for future research and practical application are put forward.

Norfloxacin adsorption and subsequent degradation on ball-milling tailored N-doped biochar

N-doping is an effective way to modify biochar for enhancing the adsorption capacity. The synthesis of N-doped biochar by the ball-milling method has been attractive due to its facile and eco-friendly approach with low energy consumption. However, the commonly used N-precursor NH₃·H₂O is environmentally harmful. It is needed to prepare safe and non-toxic N-doped biochar for large-scale production. Here, a urea N-doped biochar (U-MBC) was prepared by the ball-milling method and used for norfloxacin (NOR) removal. The results showed that U-MBC exhibited almost 4-fold higher adsorption capacity for NOR than pristine biochar in a wide pH range (3-9). The adsorption enhancement was owing to the enhancement of H-bonds, π-π electron donor-acceptor, and pore-filling interactions due to the N-doping and ball-milling method. Additionally, 89% of adsorbed NOR can be further removed after 6 h milling. The regenerated U-MBC still had a good adsorption capacity (46.27 mg g^-1) and performed well in three cycles. The knowledge gained from this study could encourage researchers to use urea or similar safe N-precursors with the ball-milling method for the large-scale production of N-doped biochar to remove antibiotic organic pollutants in the environment.

Preparation, adsorption performance and mechanism of MgO-loaded biochar in wastewater treatment: A review

Biochar is a low cost, porous and solid material with an extremely high carbon content, various types of functional groups, a large specific surface area and many other desirable characteristics. Thus, it is often used as an adsorbent or a loading matrix. Nano-magnesium oxide is a crystalline material with small particles and strong ion exchangeability. However, due to the high surface chemical energy, it easily forms agglomerates of particles. Therefore, to combine the advantages of biochar and magnesium, metal magnesium nanoparticles can be loaded onto the surface of biochar with different modification techniques, resulting in biochars with low cost and high adsorption performance to be used as an adsorption matrix (collectively referred to as Mg@BC). This review presents the effects of different Mg@BC preparation methods and synthesis conditions and summarizes the removal capabilities and adsorption mechanisms of Mg@BC for different types of pollutants in water. In addition, the review proposes the prospects for the development of Mg@BC to solve various problems in the future.

Antibiotic bioremediation by new generation biochar: Recent updates

The evolving multidrug resistance in microbes with increasing antibiotic pollution is becoming a severe global crisis. Recent developments on antibiotic remediations by biochar are promising. Advancements in biochar engineering enhanced biochar remediation efficiency to another level through developing new interactions and bonding abilities with antibiotic pollutants. Especially chemical/metal-composite modification significantly increased catalysis of biochar. The review's main focus is to underline biochar efficiency for the abatement of emerging antibiotic pollutants. Moreover, to relate feedstock, production conditions, and engineering techniques with biochar properties. Also, modification strategies are reviewed to obtain biochar or their composites before examining improved remediation potential ranging from 20 to 552 mg g^-1 for various antibiotics. Biochar offers different interactions depending on the surface functionalities e.g., π-π stacking, electrostatic, H-bonding, etc. Biochar and related composites have also been reviewed for remarkable properties e.g., photocatalysis, adsorption, and oxidation processes. Furthermore, future research directions and opportunities for biochar research are discussed.

Effective removal of pharmaceutical contaminants ibuprofen and sulfamethoxazole from water by Corn starch nanoparticles: An ecotoxicological assessment

Pharmaceutical pollutants, a vital type of emerging contaminants, have attracted researchers to study their removal from water. In this research, Corn starch nanoparticles (CSNP) have been synthesized and characterized using various analytical techniques. The synthesized CSNP was used for the biosorption of two pharmaceutical drugs, ibuprofen (IBU) and sulfamethoxazole (SUL). The influence of various experimental conditions was optimized through batch study with the removal efficiency of 86.33 % (IBU) and 85.80 % (SUL) at pH 2 and 3, initial concentration of 10 mg/L, 0.01 g of CSNP dosage. The biosorption of IBU follows Temkin, and SUL follows Langmuir isotherm models. The toxicological assessment was performed using the seeds of Vigna mungo (VM) and Vigna radiata (VR) and zebrafish to evaluate the toxic effects of pollutants on these organisms. The LC₅₀ of IBU and SUL on zebrafish before the biosorption process was 209.50 mg/L and 338.84 mg/L. After biosorption, the LC₅₀ values increase to 1435.82 mg/L for IBU and 1317.04 mg/L for SUL. Thus, CSNP is an efficient biosorbent for removing the pharmaceutical pollutants to protect ecological systems.

Amino-functionalized biochars for the detoxification and removal of hexavalent chromium in aqueous media

The objectives of the study were to evaluate and compare the efficacy of hexavalent chromium (Cr(VI)) removal by amino-modified (HDA-MPBC) and pristine biochar (MPBC) derived from an invasive plant Mimosa pigra. Prepared biochars were characterized and batch experiments were conducted to check the performance and the mechanisms of Cr(VI) removal. FTIR spectra revealed that the surface of HDA-MPBC is abundant with amino functional groups which was further confirmed by XPS analysis. The highest Cr(VI) removal for both HDA-MPBC (76%) and MPBC (62%) was observed at pH 3.0. The batch sorption data were well fitted to the Freundlich isotherm model and pseudo-second-order kinetic model, suggesting the involvement of both physisorption and chemisorption mechanisms for Cr(VI) removal. X-ray photoelectron spectroscopy studies showed that both Cr(VI) and Cr(III) were presented at the modified biochar surface after adsorption. These results indicated that the electrostatic attraction of Cr(VI) coupled with reduction of Cr(VI) to Cr(III) and complexation of Cr(III) ions with functional groups on HDA-MPBC as the most plausible mechanism for removal of Cr(VI) by modified biochar. Regeneration experiment concluded that adsorbed Cr(VI) onto the surface of HDA-MPBC had the least tendency of being desorbed in basic conditions. HDA-MPBC showed a high performance in adsorptive removal of Cr(VI) compared to pristine biochar signifying the amino modification to enhance adsorption performance of biochar in Cr(VI) removal from wastewater.

Layered Double Hydroxides as Rising-Star Adsorbents for Water Purification: A Brief Discussion

Within the frame of this article, briefly but comprehensively, we present the existing knowledge, perspectives, and challenges for the utilization of Layered Double Hydroxides (LDHs) as adsorbents against a plethora of pollutants in aquatic matrixes. The use of LDHs as adsorbents was established by considering their significant physicochemical features, including their textural, structural, morphological, and chemical composition, as well as their method of synthesis, followed by their advantages and disadvantages as remediation media. The utilization of LDHs towards the adsorptive removal of dyes, metals, oxyanions, and emerging pollutants is critically reviewed, while all the reported kinds of interactions that gather the removal are collectively presented. Finally, future perspectives on the topic are discussed. It is expected that this discussion will encourage researchers in the area to seek new ideas for the design, development, and applications of novel LDHs-based nanomaterials as selective adsorbents, and hence to further explore the potential of their utilization also for analytic approaches to detect and monitor various pollutants.

Biochar: Production, Applications, and Market Prospects in Portugal

Biochar produced during the thermochemical decomposition of biomass is an environmentally friendly replacement for different carbon materials and can be used for carbon sequestration to mitigate climate change. In this paper, current biochar production processes and top market applications are reviewed, as well as emerging biochar uses gaining momentum in the market. Various application fields of biochar, including agricultural applications (e.g., soil conditioning), adsorption (for soil and water pollutants), carbon sequestration, catalysis, or incorporation into composites or construction materials, are also presented and discussed. According to this literature overview, slow pyrolysis is the preferred process for biochar production, whereas agricultural applications (for soil conditioning and fertilization) are the most studied and market-ready solutions for biochar use. The Alentejo region (Portugal) shows tremendous potential to be a major player in the developing biochar market considering feedstock availability and large areas for biochar agricultural application. Biochar’s production potential and possible benefits were also estimated for this Portuguese region, proving that agricultural application can effectively lead to many environmental, economic, and social gains.

Surface Modification of Biochar for Dye Removal from Wastewater

Nowadays, biochar is being studied to a great degree because of its potential for carbon sequestration, soil improvement, climate change mitigation, catalysis, wastewater treatment, energy storage, and waste management. The present review emphasizes on the utilization of biochar and biochar-based nanocomposites to play a key role in decontaminating dyes from wastewater. Numerous trials are underway to synthesize functionalized, surface engineered biochar-based nanocomposites that can sufficiently remove dye-contaminated wastewater. The removal of dyes from wastewater via natural and modified biochar follows numerous mechanisms such as precipitation, surface complexation, ion exchange, cation–π interactions, and electrostatic attraction. Further, biochar production and modification promote good adsorption capacity for dye removal owing to the properties tailored from the production stage and linked with specific adsorption mechanisms such as hydrophobic and electrostatic interactions. Meanwhile, a framework for artificial neural networking and machine learning to model the dye removal efficiency of biochar from wastewater is proposed even though such studies are still in their infancy stage. The present review article recommends that smart technologies for modelling and forecasting the potential of such modification of biochar should be included for their proper applications.

Research on the non-point source pollution of microplastics

Microplastics are characterized with universality, persistence and toxicity to aquatic organisms, the pollution of microplastics has attracted worldwide attention. At present, studies on microplastic pollution were mainly focused on the composition, abundance and species of microplastics in water bodies and sediments, and few studies were focused on the source and influence characteristics of microplastics in surface water bodies. Starting from the sources of microplastic pollution in surface water of this paper, the pollution status of agricultural microplastics was analyzed, and the importance and urgency of studying microplastic pollution in agricultural non-point sources were put forward. Therefore, it was intended to provide effective scientific basis and technical support for the control of microplastics non-point source pollution in river basins.

The potential of biochar-photocatalytic nanocomposites for removal of organic micropollutants from wastewater

Biochar (BC)-photocatalyst nanocomposites have emerged as appealing water and wastewater treatment technology. Such nanocomposite materials benefit from the synergistic effect of adsorption and photocatalysis to attain improved removal of pollutants from water and wastewater. Under this review, three BC-based nanocomposite photocatalysts such as BC-TiO₂, BC-ZnO, and BC-spinel ferrites were considered. These nanocomposites acquire intrinsic properties to improve the practical limitations of the pristine BC and photocatalysts. The BC-based nanocomposites attained high photocatalytic activity, mechanical hardness, thermal stability, chemically non-reactive, magnetically permeable, reduced energy band gaps, improved reusability, and simplified recovery. Moreover, BC-based photocatalytic nanocomposites showed reduced recombination rates of the electron-hole pairs which are desirable for photocatalytic applications. However, the surface areas of the composites are usually smaller than that of the BC but higher than those of the pristine photocatalysts. Practically, the performances of the nanocomposites are much superior to those of the corresponding pristine components. This hybrid treatment technology is an emerging field and its industrial application is still at an early stage of the investigation. Therefore, exploring the full potential and practical applications of this technology is highly encouraging. Hence, this review focused on the critical evaluation of the most recent research on the synthesis, characterization, and photocatalytic treatment efficiency of the BC photocatalyst nanocomposites towards emerging pollutants in the aqueous medium. Moreover, the influence of various sources of BC feedstocks and their limitations on adsorption and photodegradation activities are discussed in detail. Finally, concluding remarks and future research directions are given to assist and shape the exploration of BC-based nanocomposite photocatalysts in water treatment.

Biochar as a potential strategy for remediation of contaminated mining soils: Mechanisms, applications, and future perspectives

Soil heavy metal contamination caused by mining activities is a global issue. These heavy metals can be enriched in plants and animals through the food chain, and eventually transferred to the human system and threatening public health. Biochar, as an environmentally friendly soil remediation agent, can effectively immobilize heavy metals in soil. However, most researchers concern more about the remediation effect and mechanism of biochar for industrial and agricultural contaminated soil, while related reviews focusing on mining soil remediation are limited. Furthermore, the remediation effect of soil in mining areas is affected by many factors, such as physicochemical properties of biochar, pyrolysis conditions, soil conditions, mining environment and application method, which can lead to great differences in the remediation effect of biochar in diverse mining areas. Therefore, it is necessary to systematically unravel the relevant knowledge of biochar remediation, which can also provide a guide for future studies on biochar remediation of contaminated soils in mining areas. The present paper first reviews the negative effects of mining activities on soil and the advantages of biochar relative to other remediation methods, followed by the mechanism and influencing factors of biochar on reducing heavy metal migration and bioavailability in mining soil were systematically summarized. Finally, the main research directions and development trends in the future are pointed out, and suggestions for future development are proposed.

Efficient Nitrate Adsorption from Groundwater by Biochar-Supported Al-Substituted Goethite

Groundwater nitrate contamination is challenging and requires efficient solutions for nitrate removal. This study aims to investigate nitrate removal using a novel adsorbent, biochar-supported aluminum-substituted goethite (BAG). The results showed that an increase in the initial Al/(Al + Fe) atomic ratio for BAGs from 0 to 20% decreased the specific surface area from 115.2 to 75.7 m2/g, but enhanced the surface charge density from 0.0180 to 0.0843 C/m2. By comparison, 10% of Al/(Al + Fe) led to the optimal adsorbent for nitrate removal. The adsorbent’s adsorption capacity was effective with a wide pH range (4–8), and decreased with increasing ionic strength. The descending order of nitrate adsorption inhibition by co-existing anions was SO42−, HCO3−, PO43−, and Cl−. The adsorption kinetics and isotherms agreed well with the pseudo-first-order equation and Langmuir model, respectively. The theoretical maximum adsorption capacity was 96.1469 mg/g. Thermodynamic analysis showed that the nitrate adsorption was spontaneous and endothermic. After 10-cycle regeneration, the BAG still kept 92.6% of its original adsorption capacity for synthetic nitrate-contaminated groundwater. Moreover, the main adsorption mechanism was attributed to electrostatic attraction due to the enhancement of surface charge density by Al substitution. Accordingly, the BAG adsorbent is a potential solution to remove nitrate from groundwater.

Adsorption and oxidation of ciprofloxacin by a novel layered double hydroxides modified sludge biochar

In this study, biochar derived from municipal sludge (SBC) was modified by CoFe-Layered double hydroxides (CoFe-LDH), and used as adsorbent and oxidant for the removal of ciprofloxacin (CIP) for the first time. Under the optimal conditions, the CIP removal rate is increased by 24% compared with the single SBC, while the removal rates of total organic carbon and total nitrogen in the modified one are increased by 24% and 27%, respectively. Mechanism investigation suggested that the specific surface area and adsorption sites of modified biochar increased, and more CIP was adsorbed to the composite surface and then oxidized by more environmental persistent free radicals contained in the CoFe-LDH@SBC, when the adsorbed CIP molecules was oxidized and degraded, the adsorption sites can be freed and thus new CIP could be adsorbed to the CoFe-LDH@SBC. In addition, the plausible degradation pathways of CIP were proposed according to high-performance liquid chromatography-mass spectrometry and density functional theory calculation. It not only reveals that CoFe-LDH@SBC has the high ability of adsorption and oxidation for CIP removal but also sheds novel insight into the application of biochar.

Comparative Life-Cycle Cost Analysis of Alternative Technologies for the Removal of Emerging Contaminants from Urban Wastewater

Emerging contaminants (ECs) continue to threaten our fragile ecosystem, yet their mitigation remains limited by economic factors. Meanwhile, a relatively expensive material, Graphene Oxide (GO), has shown promise as a solution for EC removal following further development into three graphene-based materials (GBMs): Porous graphene adsorbent (PGa), Graphene-oxide foam adsorbent (GOFa), and the hybrid filter. Due to the nuances of each synthesis process, financial costs will differ throughout the GBMs’ life cycle which have been quantified and compared in the present work at a range of possible breakthrough times. Finally, economic and environmental costs have been combined for each technology to compare eco-efficiency. Results demonstrated a substantial economic advantage of the GBMs when compared to alternative technologies, most notably the GOFa filter that incurred the lowest life-cycle costs at $1.73 ± 0.09/m3. This was mainly attributed to the lower demand of GOFa on the most expensive material required for material synthesis, hydrazine. In addition, the material demands of GOFa were more evenly distributed which suggest a higher resilience of the overall costs to price hikes of individual materials required for synthesis. In terms of eco-efficiency the GOFa filter also demonstrated the greatest improvement when compared to the reference technology These results have provided robust total investment costs for several technologies that can now offer contrast to other EC-removal solutions.

Competitive kinetics of adsorption onto activated carbon for emerging contaminants with contrasting physicochemical properties

Activated carbon (AC) can be used for the removal of emerging contaminants (e.g., drugs) in water and wastewater treatment plants. In the present study, we investigated the performance of two ACs (from coconut shell and Pinnus sp.) in the adsorption of caffeine, carbamazepine, and ricobendazole considering the compounds separately and in combination in batch-scale experiments. The concentrations of the drugs were determined by a validated method using solid-phase extraction with on-line ultra-high performance liquid chromatography-tandem mass spectrometry. The most mesoporous AC provided higher drug removal. The kinetic data were described by the pseudo-second-order, Elovich, and Weber-Morris models, while the adsorption isotherms showed a better fit to the Freundlich model, indicative of multilayer adsorption. The Dubinin-Radushkevich model was used as a first approach to estimate the mean adsorption energy (E) and the results indicate that chemisorption governed the adsorption process, with E higher than 8 kJ mol^-1. In the multicomponent assays, the adsorption of caffeine showed the greatest hindrance caused by the presence of other drugs. Multicomponent assays are fundamental to evaluate the potential adsorption capacity in real water treatment plants. Our study suggests that drugs with different structures and physicochemical properties may interact differently with ACs, especially in multicomponent solutions, with important implications for the design (e.g., volumes and areas of treatment plants) and operation (e.g., water residence time) of the treatment plants.

Pre-magnetic bamboo biochar cross-linked CaMgAl layered double-hydroxide composite: High-efficiency removal of As(III) and Cd(II) from aqueous solutions and insight into the mechanism of simultaneous purification

Trivalent arsenic (As(III)) and divalent cadmium (Cd(II)) contamination in water environment is an urgent issue because of their most toxic physicochemical properties. Herein, the simultaneous purification of As(III) and Cd(II) from aqueous solution was achieved by use of a pre-magnetic Fe modified bamboo biochar that cross-linked CaMgAl layered double-hydroxide composite (Fe-BC@LDH). In a binary system, adsorption equilibrium of As(III) and Cd(II) onto specific sorbent Fe-BC@LDH was reached within 100 and 10 min of contact time under anaerobic conditions, respectively, and the maximum adsorption capacities of As(III) and Cd(II) by Fe-BC@LDH were respectively calculated to be ⁓265.3 and ⁓320.7 mg/g at pH 4.5 and 5- and 14-times than that of unmodified biochar. Moreover, adsorption in a competitive or single system, the sorbent displayed a greater preference for Cd(II). Importantly, the removal of As(III) and Cd(II) onto the composite was more favorable in a binary system due to formation of ternary FeOCdAs bonding configuration as well as the redox transformation of As(III) to As(V), inner-sphere complexation of MOAs/Cd (MFe, Ca, Mg, Al), electrostatic attraction, and co-precipitation of scorodite and hydroxy‑iron‑cadmium. Furthermore, the nanocomposite was still highly efficient after 5 adsorption cycles. This study demonstrated that the synthesized cost-effective Fe-BC@LDH is a promising candidate for the simultaneous separation of As(III) and Cd(II) from wastewater.

Research Progress on Adsorption of Arsenic from Water by Modified Biochar and Its Mechanism: A Review

Arsenic (As) is a non-metallic element, which is widely distributed in nature. Due to its toxicity, arsenic is seriously harmful to human health and the environment. Therefore, it is particularly important to effectively remove arsenic from water. Biochar is a carbon-rich adsorption material with advantages such as large specific surface area, high porosity, and abundant functional groups, but the original biochar has limitations in application, such as limited adsorption capacity and adsorption range. The modified biochar materials have largely enhanced the adsorption capacity of As in water due to their improved physicochemical properties. In this review, the changes in the physicochemical properties of biochar before and after modification were compared by SEM, XRD, XPS, FT-IR, TG, and other characterization techniques. Through the analysis, it was found that the adsorbent dosage and pH are the major factors that influence the As adsorption capacity of the modified biochar. The adsorption process of As by biochar is endothermic, and increasing the reaction temperature is conducive to the progress of adsorption. Results showed that the main mechanisms include complexation, electrostatic interaction, and precipitation for the As removal by the modified biochar. Research in the field of biochar is progressing rapidly, with numerous achievements and new types of biochar-based materials prepared with super-strong adsorption capacity for As. There is still much space for in-depth research in this field. Therefore, the future research interests and applications are put forward in this review.

Release characteristics of phosphate from ball-milled biochar and its potential effects on plant growth

Ball-milled biochar could potentially supply phosphorus, an essential element for plant growth. To realize resource reuse and phosphorus recovery, three feedstocks (rice straw, distillers grains, and Eupatorium adenophorum) were used to prepare ball-milled biochar to evaluate its release characteristics of phosphorus and potential effects on germination and growth. The results showed that the phosphate release performance of ball-milled distillers grains biochar (DM) at 300 and 600 °C was better than that of other biochars ball-milled for 12 h. The DM prepared at 600 °C and incubated for 12 (DM-12) or 24 h (DM-24) had the best phosphate release capacity. The solution with pH 3.0 was beneficial to the release of phosphate from DM-12. The pseudo-second-order model could better fit the phosphate release of DM-12. A germination and seedling growth experiment suggested that adding 2.5 wt% DM-12 was beneficial to the height of mung beans. This study shows that DM-12 can be used as a slow-release fertilizer for the growth of mung beans, which provides a new way for resource utilization of distillers grains and phosphorus-rich biochar.

Monopersulfate in water treatment: Kinetics

The kinetics of monopersulfate based systems in the elimination of potential harmful contaminants has been assessed from a theoretical point of view. A detailed reaction mechanism sustained in the generation of radicals (mainly hydroxyl and sulfate), propagation and termination stages has been proposed. The system of first order differential equations derived has numerically been solved. The effect of main influencing parameters such as contaminant and peroxymonosulfate initial concentrations, intermediate generation, presence of organic matter, role played by anions, has been theoretically obtained. Discussion of simulated results has been accomplished by comparison with experimental data found in the literature. At the sight of the theoretical and empirical data, use of simplistic pseudo first order kinetics is discouraged. Despite considering a significant number of elemental reactions, modelling of the system reveals that a high fraction of them can be neglected due to their insignificant role played in the mechanism. The entire mechanism has been tested when peroxymonosulfate has been activated by UV radiation, although results can be fairly extrapolated to other activation strategies. Finally, a generic model capable of accounting for the effect of a diversity of parameters is proposed. No theoretical background is behind the model, however the generic model clearly improves the results obtained by simple first order kinetics.

Mitigation of organic fouling of ultrafiltration membrane by high-temperature crayfish shell biochar: Performance and mechanisms

The paper applied crayfish shell (CFS) biochar to the mitigation of ultrafiltration (UF) membrane fouling induced by humic acid (HA) and sodium alginate (SA). Results indicated that the high adsorption capacity of CFS800 to HA made it effective in alleviating the irreversible membrane fouling induced by HA, and the cross-linking reaction between the hydroxyl calcium components on CFS800 and SA reduced the reversible membrane fouling induced by SA rapidly. Further analysis showed that the "hydrogel flocs" generated by the cross-linking reaction would accumulate on the surface of the substrate membrane and form an amorphous hydrogel layer to intercept the subsequent foulant and purify the water quality further. Meanwhile, the mitigation performance of CFS800 was twice more than that of commercial powder activated carbon (PAC), and the dosage was the main factor affecting its practical application performance and thus could be considered as a promising material in alleviating membrane fouling induced by HA and SA. More importantly, the findings of the present study gave a new sight towards the application of biochar.

Emerging contaminants of high concern for the environment: Current trends and future research

Wastewater is contaminated water that must be treated before it may be transferred into other rivers and lakes in order to prevent further groundwater pollution. Over the last decade, research has been conducted on a wide variety of contaminants, but the emerging contaminants are those caused primarily by micropollutants, endocrine disruptors (EDs), pesticides, pharmaceuticals, hormones, and toxins, as well as industrially-related synthetic dyes and dye-containing hazardous pollutants. Most emerging pollutants did not have established guidelines, but even at low concentrations they could have harmful effects on humans and aquatic organisms. In order to combat the above ecological threats, huge efforts have been done with a view to boosting the effectiveness of remediation procedures or developing new techniques for the detection, quantification and efficiency of the samples. The increase of interest in biotechnology and environmental engineering gives an opportunity for the development of more innovative ways to water treatment remediation. The purpose of this article is to provide an overview of emerging sources of contaminants, detection technologies, and treatment strategies. The goal of this review is to evaluate adsorption as a method for treating emerging pollutants, as well as sophisticated and cost-effective approaches for treating emerging contaminants.

A feasible biochar derived from biogas residue and its application in the efficient adsorption of tetracycline from an aqueous solution

The recovery of carbon materials from biogas residue (BR) could efficiently promote the efficient utilization of waste and the preparation of novel materials. In this study, a green and feasible reagent of citric acid was introduced and applied in the modification of biogas residue biochar (BRC). The modified biogas residue biochar (CABRC) showed a superior adsorption ability due to its higher specific surface area (approximately 6 times that of the BRC). Additionally, the adsorption capacities of CABRC and BRC for TC were 58.25 mg/g and 20.77 mg/g, respectively, while the TC adsorption performance of CABRC was 2.8 times that of BRC. The adsorption of TC by both BRC and CABRC was primarily controlled by physical adsorption and chemical adsorption (including pore filling, hydrogen bonding, π-π DEA interaction, and electrostatic interaction). Therefore, CABRC should be considered an environmentally friendly material due to its higher adsorption performance, which could expand its application in wastewater treatment.

Phosphorus-modified biochar cross-linked Mg-Al layered double-hydroxide stabilizer reduced U and Pb uptake by Indian mustard (Brassica juncea L.) in uranium contaminated soil

The decommissioning of uranium tailings (UMT) is usually accompanied by uranium (U) contamination in soil, which poses a serious threat to human health and ecological security. Therefore, the remediation of uranium pollution in soil is imminent from ecological and environmental points of view. In recent years, the use of biochar stabilizers to repair uranium tailings (UMT) soil has become a research hotspot. In this study, a novel phosphorus-modified bamboo biochar (PBC) cross-linked Mg-Al layered double-hydroxide composite (PBC@LDH) was prepared. The hyperaccumulator plant Indian mustard (Brassica juncea L.) was selected as the test plant for outdoor pot experiments, and the stabilizers were added to the UMT soil at the dosage ratio of 15 g kg-1, which verified the bioconcentrate and translocate of U and associated heavy metal Pb in the UMT soil by Indian mustard after stabilizer remediated. The results shown that, after 50 days of growth, compared with the untreated sample (CK), the Indian mustard in PBC@LDH treatment possessed a better growth and its biomass weight of whole plant was increased by 52.7%. Meanwhile, the bioconcentration factors (BF) of U and Pb for PBC@LDH treatment were significantly decreased by 73.4% and 34.2%, respectively; and the translocation factors (TF) were also commendable reduced by 15.1% and 2.4%, respectively. Furthermore, the Tessier available forms of U and Pb in rhizosphere soil showed a remarkably decrease compared with CK, which reached by 55.97% and 14.1% after PBC@LDH stabilization, respectively. Complexation, precipitation, and reduction of functional groups released by PBC@LDH with U and Pb described the immobilization mechanisms of biochar stabilizer preventing U and Pb enrichment in Indian mustard. As well as, the formation of U-containing vesicles was prevented by the precipitation of -OH functional groups with free U and Pb ions around the cell tissue fluids and vascular bundle structure of plant roots, thereby reducing the migration risk of toxic heavy metals to above-ground parts. In conclusion, this research demonstrates that the PBC@LDH stabilizer offers a potentially effective amendment for the remediation of U contaminated soil.

Two-step pyrolysis biochar derived from agro-waste for antibiotics removal: Mechanisms and stability

This study used acetone washing biochar (BCA) and nitric-acid washing biochar (BCN) derived from bagasse to remove sulfamethoxazole (SMX) and tetracycline (TC) in water. Higher specific surface area (1119.53 m² g^-1) and graphitization degree can significantly improve decontamination efficacy, of which BCN has the highest SMX and TC sorption capacities (274.63 mg g^-1 and 353.85 mg g^-1). The kinetics, isotherms and characterization analysis indicated O-containing functional group complexation and π-π interaction were dominant mechanisms in the adsorption process. Adsorption stability experiment showed that BCA has better stability with the coexistence of anions and cations. Besides, the enhancement and competitive adsorption from the interaction between soluble organic matter and TC could facilitate TC decontamination. Therefore, bagasse biochar derived from agro-waste has a promising potential for antibiotic contaminants removal from multi-interference conditions and promotes the recycling of waste, thereby achieving harmony between materials and the ecological environment.

Preparation of carbonyl, hydroxyl, and amino-functionalized microporous carbonaceous nanospheres from syrup-based waste to remove sulfamethazine

Sulfadiazine (SDZ) was a persistent sulfonamide antibiotic with a potential risk to human health. The waste dipping syrup was considered useless and environmentally unfriendly solution. In this work, carbonyl-, hydroxyl-, and amino-functionalized microporous carbonaceous nanospheres were synthesized using waste dipping syrup with glucose, fructose, and nitrogen, which was used as precursor for hydrothermal and pyrolysis process. The products were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transformed infrared spectroscopy (FTIR), the point of zero charge (PZC), Xray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET). The carbonaceous nanospheres with large BET surface area (924.528 m²/g), micropores (2.127 nm), and high micro-porosity (89.54 %) allowed the rapid diffusion of SDZ (0.512nm×0.738 nm) into micropores of nanospheres. The majority SDZ (initial concentration = 20 mg/L) was removed (>96.8%) in the presence of 1.0 g/L nanoparticles after 40-min reaction at pH = 6.0. The adsorption capacity of SDZ onto nanospheres was 96.6 mg/g. The adsorption kinetic and equilibrium followed pseudo-first-order model and Langmuir isotherm, respectively. The intra-particle diffusion model indicated a three-step adsorption process. In addition, the regenerated nanospheres could be reused over four recycles. The optimal fabrication was realized at lower hydrothermal and pyrolysis temperature of 180 °C and 400 °C, respectively, which involved no additional chemical activating agent and had a high yield (70.8 %). Collectively, hydroxylation, carboxylation, amination, large specific surface area, and multi-microporosity may be responsible for improved adsorption performance of SDZ onto nanospheres. The findings provided a novel pathway for SDZ-loading wastewater treatment using waste syrup.

Magnetically Recyclable Loofah Biochar by KMnO4 Modification for Adsorption of Cu(II) from Aqueous Solutions

Novel KMnO₄-modified loofah biochar loaded with nano-Fe₂O₃ (FMLB) was successfully synthesized for Cu(II) adsorption. Nitrogen adsorption method, scanning electron microscope, X-ray photoelectron spectroscopy, Fourier transform infrared spectrometer, and other characterization measurements were used to evaluate the physical and chemical properties of FMLB and nano-Fe₂O₃-loaded biochar (FLB). The results show that the adsorption behavior of Cu(II) can be best fitted by the Langmuir isotherm model and the pseudo-second-order (PSO) kinetic model, indicating that the surface of FMLB was composed of homogeneous adsorption, and chemical adsorption dominated the adsorption process under optimal reaction conditions. The adsorption capacity of FMLB is improved by 42.86% compared to FLB, and it remained over 75% after four cycles. The inner-sphere complexes with manganese oxide (MnO _x ) and oxygen-containing functional groups, as well as electrostatic interaction, physical adsorption, and ion exchange, play important roles in Cu(II) adsorption. The saturation magnetization of FMLB was 10.41 emu/g, ensuring that it can be easily separated from aqueous solutions. Therefore, magnetically recyclable biochar modified by KMnO₄ is a feasible method for Cu(II) adsorption.

Advances and prospects on the aquatic plant coupled with sediment microbial fuel cell system

Energy resource scarcity and sediment pollution perniciousness have become enormous challenges, to which research has been focused on energy recovery and recycle technologies to solve both above problems. The organic matter stored in anoxic sediments of freshwater ecosystem represents a tremendous potential energy source. The system of aquatic plant coupled with sediment microbial fuel cell (AP-SMFC) has attracted much attention as a more feasible, economical and eco-friendly way to remediate sediment and surface water and generate electricity. However, the research on AP-SMFC has only been carried out in the last decade, and relevant studies have not been well summarized. In this review, the advances and prospects on AP-SMFC were systematically introduced. Firstly, the annual publication counts and keywords co-occurrence cluster of AP-SMFC were identified and visualized by resorting to the CiteSpace software, and the result showed that the research on AP-SMFC increased significantly in the last decade on the whole and will continue to increase. The bibliometric results provided valuable references and information on potential research directions for future studies. And then, the research progress and reaction mechanism of AP-SMFC were systematically described. Thirdly, the performance of AP-SMFC, including nutrients removal, organic contaminants removal, and electricity generation, was systematically summarized. AP-SMFC can enhance the removal of pollutants and electricity generation compared with SMFC without AP, and is considered to be an ideal technology for pollutants removal and resource recovery. Finally, the current challenges and future perspectives were summarized and prospected. Therefore, the review could serve as a guide for the new entrants to the field and further development of AP-SMFC application.

Application of magnetic biochar/quaternary phosphonium salt to combat the antibiotic resistome in livestock wastewater

The overuse and misuse of antibiotics in animal breeding for disease treatment and growth enhancement have been major drivers of the occurrence, diffusion, and accumulation of antibiotic resistance genes (ARGs) in wastewater. Strategies to combat ARG dissemination are pressingly needed for human and ecological safety. To achieve this goal, a biochar-based polymer, magnetic biochar/quaternary phosphonium salt (MBQ), was applied in livestock wastewater and displayed a high performance in bacterial deactivation and ARG decrease. Efficient antibacterial effects were achieved by both MBQ and quaternary phosphonium salt; however, the abundance and fold change of ARGs in the MBQ treatment indicated a more powerful ARG dissemination control than quaternary phosphonium salt. The application of MBQ evidently reduced the microbial diversity and may primarily be responsible for altering the ARG profiles in wastewater. Network, redundancy, and variation partitioning analyses were further employed to reveal that the microbial community and the presence of mobile genetic elements were two critical factors shaping the pattern of the antibiotic resistome in livestock wastewater. Considered together, these findings extend the application field of biochar and have important implications for reducing ARG dissemination risks in livestock wastewater.

One-step synthesis of garlic peel derived biochar by concentrated sulfuric acid: Enhanced adsorption capacities for Enrofloxacin and interfacial interaction mechanisms

This study put forward a one-step carbonization method by concentrated sulfuric acid to prepare garlic peel derived biochar, and the synthetic conditions were optimized by L₁₆(4⁵) orthogonal experiments. Notably, in order to study the differences between the proposed synthetic method and the conventional pyrolysis method, the concentrated sulfuric acid carbonized garlic peels biochar (CSGPB) was compared with pyrolysis derived garlic peel biochar (HTGPB) in characterization and adsorption capacities for Enrofloxacin (ENR). Results showed that CSGPB exhibited more graphite-like structures with more active functional groups on the surface, and the equilibrium adsorption capacity of CSGPB (142.3 mg g^-1) was 13.7 times of HTGPB (10.4 mg g^-1) under identical conditions. Moreover, the adsorption behaviors including adsorption kinetics, isotherms and thermodynamics of CSGPB for ENR were fully investigated and discussed. Based on the above experiments, density functional theory (DFT) simulations were performed to reveal the interfacial interaction and adsorption mechanism. Results showed π-π interaction between quinolone moieties of ENR and graphite-like structures in CSGPB might be the dominant mechanism. As for the functional groups, the adsorption energies were -40.46, -15.21 and -5.96 kJ mol^-1 for -SO₃H, -OH and -COOH, respectively, which indicated -SO₃H was the most active functional groups on the surface of CSGPB. This study provided a new sustainable perspective for the design of efficient biochars, and explored the interfacial interaction mechanism of antibiotics removal on biochars.

Biochar application in biofiltration systems to remove nutrients, pathogens, and pharmaceutical and personal care products from wastewater

Although conventional on-site wastewater treatment systems (OWTSs) provide only primary treatment of domestic wastewater, removal of a limited level of nutrients (N, P), pathogens, and pharmaceuticals and personal care products (PPCPs) could be achieved by such a treatment process. Biochar has the capacity to remove various contaminants and has been widely used as an ideal soil amendment in agriculture due to its persistence, superior nutrient-retention properties, low cost, and ready availability. However, few applications on the use of biochar in onsite wastewater treatment have been explored. In this review, we systematically reviewed the applications of biochar in filtration-based OWTSs for nutrient (N, P) removal and recovery as well as pathogen and PPCP removal. Although adsorption was the main mechanism for P, pathogen, and PPCP removal, biochar can also serve as the growth media for enhanced biological degradation, improves available alkalinity, and increases water holding capacity in the OWTSs. The biochar source, surface modification methods, and preparation procedures (e.g., pyrolysis temperature change) have significant effects on contaminant removal performance in biochar-amended OWTSs. Specifically, contradictory results have been reported on the effect of pyrolysis temperature change on biochar removal performance (i.e., increased, decreased, or no change) of N, P, and PPCPs. Wastewater composition and environmental pH also play important roles in the removal of nutrients, pathogens, and PPCPs. Overall, biochar holds great potential to serve as an alternative filtration material or to be amended to the current OWTS to improve system performance in removing a variety of contaminants at low cost.

Recent development of magnetic biochar crosslinked chitosan on heavy metal removal from wastewater - Modification, application and mechanism

Heavy metal contamination in water bodies is currently in an area of greater concern due to the adverse effects on human health. Despite the good adsorption performance of biochar, various modifications have been performed on the pristine biochar to further enhance its adsorption capability, at the same time overcome the difficulty of particles separation and mitigate the secondary pollution issues. In this review, the feasibility of chitosan-modified magnetic biochar for heavy metal removal from aqueous solution is evaluated by critically analysing existing research. The effective strategies that applied to introduce chitosan and magnetic substances into the biochar matrix are systematically reviewed. The physicochemical changes of the modified-biochar composite are expounded in terms of surface morphology, pore properties, specific surface area, surface functional groups and electromagnetism. The detailed information regarding the adsorption performances of various modified biochar towards different heavy metals and their respective underlying mechanisms are studied in-depth. The current review also analyses the kinetic and isotherm models that dominated the adsorption process and summarizes the common models that fitted well to most of the experimental adsorption data. Moreover, the operating parameters that affect the adsorption process which include solution pH, temperature, initial metal concentration, adsorbent dosage, contact time and the effect of interfering ions are explored. This review also outlines the stability of modified biochar and their regeneration rate after cycles of heavy metal removal process. Lastly, constructive suggestions on the future trends and directions are provided for better research and development of chitosan-modified magnetic biochar.

Pristine and engineered biochar for the removal of contaminants co-existing in several types of industrial wastewaters: A critical review

Biochar has been widely studied as an adsorbent for the removal of contaminants from wastewater due to its unique characteristics, such as having a large surface area, well-distributed pores and high abundance of surface functional groups. Critical review of the literature was performed to understand the state of research in utilizing biochars for industrial wastewater remediation with emphasis on pollutants that co-exist in wastewater from several industrial activities, such as textile, pharmaceutical and mining industries. Such pollutants include organic (such as synthetic dyes, phenolic compounds) and inorganic contaminants (such as cadmium, lead). Multiple correspondence analyses suggest that through batch equilibrium, columns or constructed wetlands, researchers have used mechanistic modelling of isotherms, kinetics, and thermodynamics to evaluate contaminant removal in either synthetic or real industrial wastewaters. The removal of organic and inorganic contaminants in wastewater by biochar follows several mechanisms: precipitation, surface complexation, ion exchange, cation-π interaction, and electrostatic attraction. Biochar production and modifications promote good adsorption capacity for those pollutants because biochar properties stemming from production were linked to specific adsorption mechanisms, such as hydrophobic and electrostatic interactions. For instance, adsorption capacity of malachite green ranged from 30.2 to 4066.9 mg g^-1 depending on feedstock type, pyrolysis temperature, and chemical modifications. Pyrolyzing biomass at above 500 °C might improve biochar quality to target co-existing pollutants. Treating biochars with acids can also improve pollutant removal, except that the contribution of precipitation is reduced for potentially toxic elements. Studies on artificial intelligence and machine learning are still in their infancy in wastewater remediation with biochars. Meanwhile, a framework for integrating artificial intelligence and machine learning into biochar wastewater remediation systems is proposed. The reutilization and disposal of spent biochar and the contaminant release from spent biochar are important areas that need to be further studied.

Insight into the activation mechanisms of biochar by boric acid and its application for the removal of sulfamethoxazole

Sulfamethoxazole (SMX) is frequently detected in the environment and causes a huge threaten to human health. Biochar (BC) is a metal-free adsorbent and generally exhibits a good adsorption capacity for SMX. However, the current activated methods usually result in the high energy consumption and low yield of the biochar. In this study, biochar was activated by boric acid under limited oxygen condition. The yield of biochar was increased by 103% after the activated by boric acid. The specific surface area of BC was significantly increased from 766.6 m²·g^-1 to 1190.6 m²·g^-1. The intensity of the (111) diamond peak of B-BC was higher than that of BC, suggesting that boric acid affected the surface pyrolysis temperature of biochar. The proposed roles of boric acid in the activation process were to: 1) enhance the generation of micropores during the pyrolysis process; 2) improve the yield of biochar via the transformation pathways of C-corresponding bonds and physical blocking. The boric acid activated biochar (B-BC) had a higher adsorption capacity for SMX than BC under the various aqueous conditions. Hence, boric acid activated biochar is a promising porous adsorbent to enhance the removal of SMX and achieve practical application.

Adsorption of Malachite Green and Pb2+ by KMnO4-Modified Biochar: Insights and Mechanisms

In this study, the feasibility and mechanism of Pb2+ and malachite green (MG) adsorption from wastewater using KMnO4-modified bamboo biochar (KBC) was evaluated. The KBC was characterized by SEM–EDS, XRD, FTIR and XPS. The adsorption results for Pb2+ conformed to pseudo-second-order kinetics and the Langmuir model theory. Unlike the case for Pb2+, the Freundlich model better described the adsorption behaviour of MG, indicating that adsorption occurred within multiple molecular layers. Both pseudo-first-order kinetics and pseudo-second-order kinetics fit the MG adsorption data well, indicating that physical adsorption was involved in the adsorption process. In addition, the maximum adsorption capacity for Pb2+/MG was 123.47/1111.11 mg·g−1, KBC had high adsorption capacities for Pb2+ and MG, and the mechanisms of Pb2+ adsorption were mineral precipitation, functional group complexation, and cation-π interactions, while the main mechanisms for MG adsorption were pore filling, π–π interactions, and functional group complexation. In this study, KMnO4-modified biochar was prepared and used as an efficient adsorbent, and showed good application prospects for treatment of wastewater containing MG and Pb2+.

Three-dimension hierarchical composite via in-situ growth of Zn/Al layered double hydroxide plates onto polyaniline-wrapped carbon sphere for efficient naproxen removal

In this work, a novel adsorbent, 3D hierarchical CS@PANI@ZnAl-LDH composite, has been successfully fabricated through the hydrothermal synthesis of the carbon sphere, oxidative polymerization of polyaniline, and in-site growth of ZnAl-layered double hydroxides, simultaneously applied for the naproxen removal from aqueous solutions. The dynamics and isotherms fit better with the pseudo-second-order and Langmuir model, demonstrating the chemisorption, monolayer, and endothermic process. In addition, the high uptake capacities of CS@PANI@ZnAl-LDH for naproxen was 545.5 mg/g at 298 K when the pH was 5.0, outperforming most previously reported materials. Moreover, after five adsorption-desorption cycles, the spent CS@PANI@ZnAl-LDH maintains high removal efficiency and structural composition, revealing excellent recyclability and stability. Furthermore, Fourier transformed infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS) analyses indicate electrostatic interactions, π-π interactions, and hydrogen bonding between CS@APNI@ZnAl-LDH and naproxen. Quantitative analyses, Localized orbit locator (LOL)-π isosurface, and Independent Gradient Model further verify the adsorption mechanisms mentioned above, indicating the synergistic effects between PANI and ZnAl-LDH improve the elimination ability for naproxen. Significantly, Hirshfeld surface analyses reveal that naproxen behaves as the H-bond acceptor, and the ZnAl-LDH acts as the H-bond donor. This work provided a feasible way to design purification materials for wastewater treatment.

Removal of pharmaceuticals from water using sewage sludge-derived biochar: A review

In recent years, considerable attention has been paid to the beneficial utilization of sewage sludge to reduce the risks associated with sludge disposal. Besides other applications of sludge, biochar produced from sludge has also been employed for the elimination of various pollutants from water. This review critically evaluates the recent progress in applications of sludge-based biochar for the adsorption of pharmaceuticals from water. The synthesis techniques of biochar production from sludge and their effects on physicochemical characteristics of produced biochar are discussed. The removal of various pharmaceuticals by sludge-based biochar are described in detail, with the emphasis on the adsorption mechanism and their reusability potential. It is evident from the literature that sludge-based biochar has demonstrated excellent potential for the adsorption of numerous pharmaceuticals from the aqueous phase. The major hurdles and issues related to the synthesis of sludge-based biochar and applications are highlighted, with reference to the adsorption of pharmaceuticals. Finally, a roadmap is suggested along with future research directions to ensure the sustainable production of biochar from sludge and its applications in water treatment.

Adsorptive remediation of naproxen from water using in-house developed hybrid material functionalized with iron oxide

Every year, a considerable volume of medications is consumed. Because these medications are not entirely eliminated in the sewage treatment plants and impact the surface waterways, the environmental pollution problem arises. This study objective was to evaluate the possibility of using an absorbent material made with of polyethylene terephthalate and sugarcane bagasse ash functionalized with iron oxide (PETSCA/Fe³⁺) in the removal of naproxen from water. The feasibility of having viable features in becoming an efficient adsorbent was first determined. The batch test was performed, allowing the dose effect, adsorption kinetics, and isotherm models to be evaluated. The determination of naproxen (NAP) concentration in water was analyzed on a high-performance liquid chromatograph and Langmuir method best represented the adsorption isotherm model. PETSCA/Fe³⁺ adsorbent material demonstrated potential in the naproxen removal at a low cost. The batching process was satisfactory, with 0.30 g of composite being the optimum fit for the system. The adsorption kinetics was determined and described by the pseudo second order model, with an average correlation coefficient (R²) of 0.974. The adsorption system model was best represented by the Langmuir isotherm curve. Moreover, adsorption in the presence of H₂O₂ had a positive impact on the process, removing 81.9% of NAP, whereas the process without H₂O₂ did not remove more than 62.0% of NAP. Therefore, because of its good qualities for NAP removal, PETSCA/Fe³⁺ is recommended as adsorbent material, primarily in small-volume water filtration systems.

Adsorption of norfloxacin from aqueous solution on biochar derived from spent coffee ground: Master variables and response surface method optimized adsorption process

In this study, biochar derived from spent coffee grounds (SCGB) was used to adsorb norfloxacin (NOR) in water. The biochar properties were interpreted by analysis of the specific surface area, morphology, structure, thermal stability, and functional groups. The impacts of pH, NOR, and ion's present on SCGB performance were examined. The NOR adsorption mode of SCGB is best suited to the Langmuir model (R² = 0.974) with maximum absorption capacity (69.8 mg g^-1). By using a Response Surface Method (RSM), optimal adsorption was also found at pH of 6.26, NOR of 24.69 mg L^-1, and SCGB of 1.32 g L^-1. Compared with biochars derived from agriculture such as corn stalks, willow branches, potato stem, reed stalks, cauliflower roots, wheat straw, the NOR adsorption capacity of SCGB was 2-30 times higher, but less than 3-4 times for biochars made from Salix mongolica, luffa sponge and polydopamine microspheres. These findings reveal that spent coffee grounds biochar could effectively remove NOR from aqueous solutions. Approaching biochar derived from coffee grounds would be a promising eco-friendly solution because it utilizes solid waste, saves costs, and creates adsorbents to deal with emerging pollutants like antibiotics.

Removal of emerging contaminants (bisphenol A and antibiotics) from kitchen wastewater by alkali-modified biochar

Using current wastewater treatment technologies, it can be challenging to remove the emerging contaminants (ECs) present in kitchen wastewater (KW) of complex compositions and high organic content. In this study, biochar, derived from straw, was modified as an adsorbent to remove ECs such as bisphenol A (BPA), tetracycline (TC) and ofloxacin (OFL) from a complex KW system. An alkali-modified biochar, having larger specific surface areas and stronger hydrophobicity, was found to exhibit a higher adsorption capacity, with more than 95% of the target ECs being removed. Indeed, in a static operation mode, the alkali-modified biochar had maximum adsorption capacities of 71.43, 101.01 and 54.05 mg/g for BPA, TC, and OFL, respectively. The adsorption kinetics and isotherms models indicated that the adsorption process was controlled by chemisorption, as well as the monolayer adsorption of contaminants onto the external and internal surfaces of the alkali-modified biochar. The adsorption of TC and OFL was significantly affected by the initial pH values of KW. However, the presence of different environmental factors (COD, NH₄⁺ and PO₄^3-) had little effects on the adsorption of the contaminants. The alkali-modified biochar was further tested in a fixed-bed column where the maximum dynamic adsorption capacities for BPA and OFL were 55 and 45 mg/g, representing about 75% and 83% of the static saturated adsorption capacities. These findings can be of major significance for the application of alkali-modified biochar in the removal of ECs from complex KW systems.