Effects of surface wettability and contact time on protein adhesion to biomaterial surfaces

On The Origin of Shear Stress Induced Myogenesis Using PMMA Based Lab-on-Chip

One of the central themes in cell and tissue engineering is to develop an understanding as to how biophysical cues can influence cell functionality changes. The flow induced shear stress is regarded as one such biophysical cue to influence physiological changes in shear-sensitive tissues, in vivo. The origin of such phenomena is, however, poorly understood. While addressing such an issue, the present work demonstrates the intriguing synergistic effect of shear stress and spatial constraints in inducing aligned growth and differentiation of myoblast cells to myotubes. In a planned set of in vitro experiments, the regulation of laminar flow regime within a narrow window was obtained in a PMMA-based Lab-on-Chip (LOC) device, wherein the murine muscle cells (C2C12), chosen for their phenotypical differentiation stages, were cultured under graded shear conditions. The two factors of shear stress and spatial allowance were decoupled by another two sets of experiments. This aspect has been conclusively established using a PMMA device having a fixed width microchannel with varying shear and an identical amount of shear with different width of channels. On the basis of the extensive analysis of biochemical assays (WST-1, picogreen) together with gene expression using qRT-PCR and cell morphological changes (fluorescence/confocal microscopy), extensive differentiation of the myoblasts into myotubes is found to be dependent on both shear stress and spatial allocation with a maximum at an optimal shear of ca. 16 mPa. Quantitatively, the mRNA expression of myogenic biomarkers, i.e., myogenin, MyoD, and neogenin, exhibited 10- to 50-fold changes at ca. 16 mPa shear flow, compared to that under static conditions. Also, myotube aspect ratio and myotube density are modulated with shear stress and are in commensurate with gene expression changes. The flow cytometry analysis further confirmed that the cell cycle arrest at the G1/G0 phase triggers the onset of myogenesis. Taken together, the present study unambiguously establishes qualitative and quantitative biophysical basis for the origin of myogenesis toward the critical shear stress of murine myoblasts in a microfludic device, in vitro.

Surface dependent contact activation of factor XII and blood plasma coagulation induced by mixed thiol surfaces

Studies of the activation of FXII in both platelet poor plasma and in neat buffer solutions were undertaken for a series of mixed thiol self-assembled monolayers spanning a broad range of water wettability. A wide spectrum of carboxyl/methyl-, hydroxyl/methyl-, and amine/methyl-thiol modified surfaces were prepared, characterized, and then utilized as the procoagulant materials in a series of FXII activation studies. X-ray photoelectron spectroscopy was utilized to verify the sample surface's thiol composition and contact angles measured to determine the sample surface's wettability. These samples were then used in in vitro coagulation assays using a 50% mixture of recalcified plasma in phosphate buffered saline. Alternatively, the samples were placed into purified FXII solutions for 30 min to assess FXII activation in neat buffer solution. Plasma coagulation studies supported a strong role for anionic surfaces in contact activation, in line with the traditional models of coagulation, while the activation results in neat buffer solution demonstrated that FXIIa production is related to surface wettability with minimum levels of enzyme activation observed at midrange wettabilities, and no statistically distinguishable differences in FXII activation seen between highly wettable and highly nonwettable surfaces. Results demonstrated that the composition of the solution and the surface properties of the material all contribute to the observation of contact activation, and the activation of FXII is not specific to anionic surfaces as has been long believed.

Molecular Dynamics Insights into Water-Parylene C Interface: Relevance of Oxygen Plasma Treatment for Biocompatibility

Solid-water interfaces play a vital role in biomaterials science because they provide a natural playground for most biochemical reactions and physiological processes. In the study, fully atomistic molecular dynamics simulations were performed to investigate interactions between water molecules and several surfaces modeling for unmodified and modified parylene C surfaces. The introduction of -OH, -CHO, and -COOH to the surface and alterations in their coverage significantly influence the energetics of interactions between water molecules and the polymer surface. The theoretical studies were complemented with experimental measurements of contact angle, surface free energy, and imaging of osteoblast cells adhesion. Both MD simulations and experiments demonstrate that the optimal interface, in terms of biocompatibility, is obtained when 60% of native -Cl groups of parylene C surface is exchanged for -OH groups. By exploring idealized models of bare and functionalized parylene C, we obtained a unique insight into molecular interactions at the water-polymer interface. The calculated values of interaction energy components (electrostatic and dispersive) correspond well with the experimentally determined values of surface free energy components (polar and dispersive), revealing their optimal ratio for cells adhesion. The results are discussed in the context of controllable tuning and functionalization of implant polymeric coating toward improved biocompatibility.

Wetting ability of biological liquids in presence of metallic nanoparticles

The wetting ability of water and of some biological liquids was measured on different biocompatible surfaces with and without different colloidal metals. Insoluble nanoparticles disperse in biological tissues enhance some properties, such as the interface adhesion between two surfaces, the X-ray contrast of medical images and the absorbed dose during radiotherapy treatments. The introduction of nanoparticles in the liquids generally improves the wetting ability and changes other properties of the solution, due to the different distribution of the adhesion forces, to the nature, morphology and concentration of the added nanoparticles. An investigation on the contact angle of the liquid drops, physiological liquids, including the human blood, placed on different substrates (polymers, ceramics and metals) with and without the use of metallic nanoparticles is presented, evaluated and discussed.

Hemocompatibility studies on a degradable polar hydrophobic ionic polyurethane (D-PHI)

Biomaterial blood compatibility is a complex process that involves four key pathways, including the coagulation cascade, the complement system, platelets, and leukocytes. While many studies have addressed the initial contact of blood with homopolymeric (e.g. Teflon) or simple copolymeric (e.g. Dacron) biomaterials, relatively less attention has been given to investigating blood coagulation with respect to complex copolymeric systems containing well defined and diverse function. The current study sought to assess the hemocompatibility of a complex polyurethane (PU) containing a unique combination of polar, hydrophobic, and ionic domains (D-PHI). This included a whole blood (WB) study, followed by tests on the intrinsic and extrinsic coagulation pathways, complement activation, platelet activation, and an assessment of the effect of leukocytes on platelet-biomaterial interactions. A small increase in blood clot formation was observed on D-PHI in WB; however, there was no significant increase in clotting via the intrinsic coagulation cascade. No significant increase in platelet adhesion and only a very slight increase in platelet activation were observed in comparison to albumin-coated substrates (negative control). D-PHI showed mild complement activation and increased initiation of the extrinsic pathway of coagulation, along with the observation that leukocytes were important in mediating platelet-biomaterial interactions. It is proposed that complement is responsible for activating coagulation by inciting leukocytes to generate tissue factor (TF), which causes extrinsic pathway activation. This low level of blood clotting on D-PHI's surface may be necessary for the beneficial wound healing of vascular constructs that has been previously reported for this material.

STATEMENT OF SIGNIFICANCE

Understanding the hemocompatibility of devices intended for blood-contacting applications is important for predicting device failure. Hemocompatibility is a complex parameter (affected by at least four different mechanisms) that measures the level of thrombus generation and immune system activation resulting from blood-biomaterial contact. The complexity of hemocompatibility implies that homopolymers are unlikely to solve the clotting challenges that face most biomaterials. Diversity in surface chemistry (containing hydrophobic, ionic, and polar domains) obtained from engineered polyurethanes can lead to favourable interactions with blood. The current research considered the effect of a highly functionalized polyurethane biomaterial on all four mechanisms in order to provide a comprehensive in vitro measure of the hemocompatibility of this unique material and the important mechanisms at play.

Activation of Macrophages in Response to Biomaterials

Macrophages are the initial biologic responders to biomaterials. These highly plastic immune sentinels control and modulate responses to materials, foreign or natural. The responses may vary from immune stimulatory to immune suppressive. Several parameters have been identified that influence macrophage response to biomaterials, specifically size, geometry, surface topography, hydrophobicity, surface chemistry, material mechanics, and protein adsorption. In this review, the influence of these parameters is supported with examples of both synthetic and naturally derived materials and illustrates that a combination of these parameters ultimately influences macrophage responses to the biomaterial. Having an understanding of these properties may lead to highly efficient design of biomaterials with desirable biologic response properties.

Control of interface interactions between natural rubber and solid surfaces through charge effects: an AFM study in force spectroscopic mode

Adhesion of nanoparticles (natural rubber) is monitored by slight changes in the surface charge state of the contacting solid surfaces.

Protein droplet actuation on superhydrophobic surfaces: a new approach toward anti-biofouling electrowetting systems

Anti-biofouling behaviour of an electrowetting device using off-the-shelf superhydrophobic materials is demonstrated through protein adsorption measurement and protein-laden droplet actuation.

Controlling wettability of PECVD-deposited dual organosilicon/carboxylic acid films to influence DNA hybridisation assay efficiency

Plasma oxidation of Zeonor and deposition of TEOS/AA thin film showing dual layer effect on the surface.

Parallel Control over Surface Charge and Wettability Using Polyelectrolyte Architecture: Effect on Protein Adsorption and Cell Adhesion

Surface charge and wettability, the two prominent physical factors governing protein adsorption and cell adhesion, have been extensively investigated in the literature. However, a comparison between these driving forces in terms of their independent and cooperative effects in affecting adhesion is rarely explored on a systematic and quantitative level. Herein, we formulate a protocol that features two-dimensional control over both surface charge and wettability with limited cross-parameter influence. This strategy is implemented by controlling both the polyion charge density in the layer-by-layer (LbL) assembly process and the polyion side-chain chemical structures. The 2D property matrix spans surface isoelectric points ranging from 5 to 9 and water contact angles from 35 to 70°, with other interferential factors (e.g., roughness) eliminated. The interplay between these two surface variables influences protein (bovine serum albumin, lysozyme) adsorption and 3T3 fibroblast cell adhesion. For proteins, we observe the presence of thresholds for surface wettability and electrostatic driving forces necessary to affect adhesion. Beyond these thresholds, the individual effects of electrostatic forces and wettability are observed. For fibroblast, both surface charge and wettability have an effect on its adhesion. The combined effects of positive charge and hydrophilicity lead to the highest cell adhesion, whereas negative charge and hydrophobicity lead to the lowest cell adhesion. Our design strategy can potentially form the basis for studying the distinct behaviors of electrostatic force or wettability driven interfacial phenomena and serve as a reference in future studies assessing protein adsorption and cell adhesion to surfaces with known charge and wettability within the property range studied here.

Film Thickness Determines Cell Growth and Cell Sheet Detachment from Spin-Coated Poly(N-Isopropylacrylamide) Substrates

Poly(N-isopropylacrylamide) (pNIPAm) is widely used to fabricate thermoresponsive surfaces for cell sheet detachment. Many complex and expensive techniques have been employed to produce pNIPAm substrates for cell culture. The spin-coating technique allows rapid fabrication of pNIPAm substrates with high reproducibility and uniformity. In this study, the dynamics of cell attachment, proliferation, and function on non-cross-linked spin-coated pNIPAm films of different thicknesses were investigated. The measurements of advancing contact angle revealed increasing contact angles with increasing film thickness. Results suggest that more hydrophilic 50 and 80 nm thin pNIPAm films are more preferable for cell sheet fabrication, whereas more hydrophobic 300 and 900 nm thick spin-coated pNIPAm films impede cell attachment. These changes in cell behavior were correlated with changes in thickness and hydration of pNIPAm films. The control of pNIPAm film thickness using the spin-coating technique offers an effective tool for cell sheet-based tissue engineering.

Sticky Situation: An Investigation of Robust Aqueous-Based Recombinant Spider Silk Protein Coatings and Adhesives

The mechanical properties and biocompatibility of spider silks have made them one of the most sought after and studied natural biomaterials. A biomimetic process has been developed that uses water to solvate purified recombinant spider silk proteins (rSSps) prior to material formation. The absence of harsh organic solvents increases cost effectiveness, safety, and decreases the environmental impact of these materials. This development allows for the investigation of aqueous-based rSSps as coatings and adhesives and their potential applications. In these studies it was determined that fiber-based rSSps in nonfiber formations have the capability to coat and adhere numerous substrates, whether rough, smooth, hydrophobic, or hydrophilic. Further, these materials can be functionalized for a variety of processes. Drug-eluting coatings have been made with the capacity to release a variety of compounds in addition to their inherent ability to prevent blood clotting and biofouling. Additionally, spider silk protein adhesives are strong enough to outperform some conventional glues and still display favorable tissue implantation properties. The physical properties, corresponding capabilities, and potential applications of these nonfibrous materials were characterized in this study. Mechanical properties, ease of manufacturing, biodegradability, biocompatibility, and functionality are the hallmarks of these revolutionary spider silk protein materials.

Plasma-modified nitric oxide-releasing polymer films exhibit time-delayed 8-log reduction in growth of bacteria

Tygon(®) and other poly(vinyl chloride)-derived polymers are frequently used for tubing in blood transfusions, hemodialysis, and other extracorporeal circuit applications. These materials, however, tend to promote bacterial proliferation which contributes to the high risk of infection associated with device use. Antibacterial agents, such as nitric oxide donors, can be incorporated into these materials to eliminate bacteria before they can proliferate. The release of the antimicrobial agent from the device, however, is challenging to control and sustain on timescales relevant to blood transport procedures. Surface modification techniques can be employed to address challenges with controlled drug release. Here, surface modification using H2O (v) plasma is explored as a potential method to improve the biocompatibility of biomedical polymers, namely, to tune the nitric oxide-releasing capabilities from Tygon films. Film properties are evaluated pre- and post-treatment by contact angle goniometry, x-ray photoelectron spectroscopy, and optical profilometry. H2O (v) plasma treatment significantly enhances the wettability of the nitric-oxide releasing films, doubles film oxygen content, and maintains surface roughness. Using the kill rate method, the authors determine both treated and untreated films cause an 8 log reduction in the population of both Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus. Notably, however, H2O (v) plasma treatment delays the kill rate of treated films by 24 h, yet antibacterial efficacy is not diminished. Results of nitric oxide release, measured via chemiluminescent detection, are also reported and correlated to the observed kill rate behavior. Overall, the observed delay in biocidal agent release caused by our treatment indicates that plasma surface modification is an important route toward achieving controlled drug release from polymeric biomedical devices.

Measuring protein isoelectric points by AFM-based force spectroscopy using trace amounts of sample

Protein charge at various pH and isoelectric point (pI) values is important in understanding protein function. However, often only trace amounts of unknown proteins are available and pI measurements cannot be obtained using conventional methods. Here, we show a method based on the atomic force microscope (AFM) to determine pI using minute quantities of proteins. The protein of interest is immobilized on AFM colloidal probes and the adhesion force of the protein is measured against a positively and a negatively charged substrate made by layer-by-layer deposition of polyelectrolytes. From the AFM force-distance curves, pI values with an estimated accuracy of ±0.25 were obtained for bovine serum albumin, myoglobin, fibrinogen and ribonuclease A over a range of 4.7-9.8. Using this method, we show that the pI of the 'footprint' of the temporary adhesive proteins secreted by the barnacle cyprid larvae of Amphibalanus amphitrite is in the range 9.6-9.7.

A novel multistep method for chondroitin sulphate immobilization and its interaction with fibroblast cells

Polymeric biomaterials are widely used in medical applications owing to their low cost, processability and sufficient toughness. Surface modification by creating a thin film of bioactive agents is promising technique to enhance cellular interactions, regulate the protein adsorption and/or avoid bacterial infections. Polyethylene is one of the most used polymeric biomaterial but its hydrophobic nature impedes its further chemical modifications. Plasma treatment is unique method to increase its hydrophilicity by incorporating hydrophilic oxidative functional groups and tailoring the surface by physical etching. Furthermore, grafting of polymer brushes of amine group containing monomers onto the functionalized surface lead to strongly immobilized bioactive agents at the final step. Chondroitin sulphate is natural polysaccharide mainly found in connective cartilage tissue which used as a bioactive agent to immobilize onto polyethylene surface by multistep method in this study.

Self-driven perfusion culture system using a paper-based double-layered scaffold

Shear stress caused by fluid flow is known to promote tissue development from cells in vivo. Therefore, perfusion cultures have been studied to investigate the mechanisms involved and to fabricate engineered tissues in vitro, particularly those that include blood vessels. Microfluidic devices, which function with fine machinery of chambers and microsyringes for fluid flow and have small culture areas, are conventionally used for perfusion culture. In contrast, we have developed a self-driven perfusion culture system by using a paper-based double-layered scaffold as the fundamental component. Gelatin microfibers were electrospun onto a paper material to prepare the scaffold system, in which the constant perfusion of the medium and the scaffold for cell adhesion/proliferation were functionally divided into a paper and a gelatin microfiber layer, respectively. By applying both the capillary action and siphon phenomenon of the paper-based scaffold, which bridged two medium chambers at different height levels, a self-driven medium flow was achieved and the flow rate was also stable, constant, and quantitatively controllable. Moreover, the culture area was enlargeable to the cm(2) scale. The endothelial cells cultivated on this system oriented along the medium-flow direction, suggesting that the shear stress caused by medium flow was effectively applied. This perfusion culture system is expected to be useful for fabricating three-dimensional and large engineered tissues in the future.

Mechanically tuned nanocomposite coating on titanium metal with integrated properties of biofilm inhibition, cell proliferation, and sustained drug delivery

The clinical success of coated implants in executing biological functions inclusive of sustainable drug release and long term antibacterial activity without antibiotics is critical. To this aim, a nanohybrid of silver nanoparticles (AgNPs) cored in polyvinyl alcohol nanocapsules (Ag-PVA NCs) embedded in chitosan (CS) matrix loaded with anti-inflammatory drug naproxen was prepared. The synthesized nanohybrids that were subjected to coatings on (3-aminopropyl)triethoxysilane (APTES) treated titanium (Ti) metal exhibited dual role of excellent inhibition on biofilm formation and sustained drug release. These dual characteristics are achieved mainly based on intrinsic antibacterial property of AgNPs and differential entrapment of drug in PVA polymeric shell of AgNPs and CS matrix. The coatings also demonstrated enhanced mechanical properties with increasing inorganic filler and stress shielding on Ti metal. The biocompatibility tests involving adhesion, proliferation and differentiation of osteoblast cells demonstrated the efficacy of Ag-PVA NCs embedded in CS matrix as a suitable coating material for orthopedic applications.

Improved antifouling properties and selective biofunctionalization of stainless steel by employing heterobifunctional silane-polyethylene glycol overlayers and avidin-biotin technology

A straightforward solution-based method to modify the biofunctionality of stainless steel (SS) using heterobifunctional silane-polyethylene glycol (silane-PEG) overlayers is reported. Reduced nonspecific biofouling of both proteins and bacteria onto SS and further selective biofunctionalization of the modified surface were achieved. According to photoelectron spectroscopy analyses, the silane-PEGs formed less than 10 Å thick overlayers with close to 90% surface coverage and reproducible chemical compositions. Consequently, the surfaces also became more hydrophilic, and the observed non-specific biofouling of proteins was reduced by approximately 70%. In addition, the attachment of E. coli was reduced by more than 65%. Moreover, the potential of the overlayer to be further modified was demonstrated by successfully coupling biotinylated alkaline phosphatase (bAP) to a silane-PEG-biotin overlayer via avidin-biotin bridges. The activity of the immobilized enzyme was shown to be well preserved without compromising the achieved antifouling properties. Overall, the simple solution-based approach enables the tailoring of SS to enhance its activity for biomedical and biotechnological applications.

A New Route of Fucoidan Immobilization on Low Density Polyethylene and Its Blood Compatibility and Anticoagulation Activity

Beside biomaterials’ bulk properties, their surface properties are equally important to control interfacial biocompatibility. However, due to the inadequate interaction with tissue, they may cause foreign body reaction. Moreover, surface induced thrombosis can occur when biomaterials are used for blood containing applications. Surface modification of the biomaterials can bring enhanced surface properties in biomedical applications. Sulfated polysaccharide coatings can be used to avoid surface induced thrombosis which may cause vascular occlusion (blocking the blood flow by blood clot), which results in serious health problems. Naturally occurring heparin is one of the sulfated polysaccharides most commonly used as an anticoagulant, but its long term usage causes hemorrhage. Marine sourced sulfated polysaccharide fucoidan is an alternative anticoagulant without the hemorrhage drawback. Heparin and fucoidan immobilization onto a low density polyethylene surface after functionalization by plasma has been studied. Surface energy was demonstrated by water contact angle test and chemical characterizations were carried out by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Surface morphology was monitored by scanning electron microscope and atomic force microscope. Finally, their anticoagulation activity was examined for prothrombin time (PT), activated partial thromboplastin time (aPTT), and thrombin time (TT).

BSA/HSA ratio modulates the properties of Ca(2+)-induced cold gelation scaffolds

An effective tissue engineering approach requires adjustment according to the target tissue to be engineered. The possibility of obtaining a protein-based formulation for the development of multivalent tunable scaffolds that can be adapted for several types of cells and tissues is explored in this work. The incremental substitution of bovine serum albumin (BSA) by human serum albumin (HSA), changing the scaffolds' hydrophilic/hydrophobic ratio, on a previously optimized scaffold formulation resulted in a set of uniform porous scaffolds with different physical properties and associated cell proliferation profile along time. There was a general trend towards an increase in hydrophilicity, swelling degree and in vitro degradation of the scaffolds with increasing replacement of BSA by HAS. The set of BSA/HSA scaffolds presented distinct values for the storage (elastic) modulus and loss factor which were similar to those described for different native tissues such as bone, cartilage, muscle, skin and neural tissue. The preferential adhesion and proliferation of skin fibroblasts on the BSA25%HSA75% and HSA100% scaffolds, as predicted by their viscoelastic properties, demonstrate that the BSA/HSA scaffold formulation is promising for the development of scaffolds that can be tuned according to the tissue to be repaired and restored.

Is dialdehyde starch a valuable cross-linking agent for collagen/elastin based materials?

Collagen and elastin are the main structural proteins in mammal bodies. They provide mechanical support, strength, and elasticity to various organs and tissues, e.g. skin, tendons, arteries, and bones. They are readily available, biodegradable, biocompatible and they stimulate cell growth. The physicochemical properties of collagen and elastin-based materials can be modified by cross-linking. Glutaraldehyde is one of the most efficient cross-linking agents. However, the unreacted molecules can be released from the material and cause cytotoxic reactions. Thus, the aim of our work was to investigate the influence of a safer, macromolecular cross-linking agent--dialdehyde starch (DAS). The properties of hydrogels based on collagen/elastin mixtures (95/5, 90/10) containing 5 and 10% of DAS and neutralized via dialysis against deionized water were tested. The homogenous, transparent, stiff hydrogels were obtained. The DAS addition causes the formation of intermolecular cross-linking bonds but does not affect the secondary structure of the proteins. As a result, the thermal stability, mechanical strength, and, surprisingly, swelling ability increased. At the same time, the surface properties test and in vitro study show that the materials are attractive for 3T3 cells. Moreover, the materials containing 10% of DAS are more resistant to enzymatic degradation.

Protein-surface interactions on stimuli-responsive polymeric biomaterials

Responsive surfaces: a review of the dependence of protein adsorption on the reversible volume phase transition in stimuli-responsive polymers. Specifically addressed are a widely studied subset: thermoresponsive polymers. Findings are also generalizable to other materials which undergo a similarly reversible volume phase transition. As of 2015, over 100,000 articles have been published on stimuli-responsive polymers and many more on protein-biomaterial interactions. Significantly, fewer than 100 of these have focused specifically on protein interactions with stimuli-responsive polymers. These report a clear trend of increased protein adsorption in the collapsed state compared to the swollen state. This control over protein interactions makes stimuli-responsive polymers highly useful in biomedical applications such as wound repair scaffolds, on-demand drug delivery, and antifouling surfaces. Outstanding questions are whether the protein adsorption is reversible with the volume phase transition and whether there is a time-dependence. A clear understanding of protein interactions with stimuli-responsive polymers will advance theoretical models, experimental results, and biomedical applications.

Failure mechanisms in denture adhesives

OBJECTIVE

The mechanical properties of bio adhesives in oral care application are expected to be critical in defining the stability and release of devices such as dentures from the oral tissue. A multiscale experimental mechanical approach is used to evaluate the performance of denture adhesive materials.

METHODS

The inherent mechanical behavior of denture fixatives was examined by separating adhesive material from a representative polymethyl methacrylate (PMMA) surface using atomic force microscopy (AFM) approaches and compared to macroscopic mechanical testing.

RESULTS

Failure of denture adhesive material was found to be critically dependent on the formation of fibrillar structures within the adhesive. Small scale mechanical testing provided evidence for the mechanical properties of the fibrillar structures formed within the adhesive in macroscopic mechanical testing and indicated the importance of the forces required to fail the adhesive at these small length scales in controlling both the maximum forces sustained by the bulk material as well as the ease of separating the adhesive from PMMA surfaces.

SIGNIFICANCE

Our results are important in defining the performance of denture fixative materials and their control of adhesive behavior, allowing the potential to tune properties required in the adhesion and removal of dentures.

Surface free energy predominates in cell adhesion to hydroxyapatite through wettability

The initial adhesion of cells to biomaterials is critical in the regulation of subsequent cell behaviors. The purpose of this study was to investigate a mechanism through which the surface wettability of biomaterials can be improved and determine the effects of biomaterial surface characteristics on cellular behaviors. We investigated the surface characteristics of various types of hydroxyapatite after sintering in different atmospheres and examined the effects of various surface characteristics on cell adhesion to study cell-biomaterial interactions. Sintering atmosphere affects the polarization capacity of hydroxyapatite by changing hydroxide ion content and grain size. Compared with hydroxyapatite sintered in air, hydroxyapatite sintered in saturated water vapor had a higher polarization capacity that increased surface free energy and improved wettability, which in turn accelerated cell adhesion. We determined the optimal conditions of hydroxyapatite polarization for the improvement of surface wettability and acceleration of cell adhesion.

Hydroxyapatite with High Carbonate Substitutions Promotes Osteoclast Resorption through Osteocyte-like Cells

The role of ceramic biomaterials in the repair of bone defects varies from materials that purely fill the physical defects of the injured bone to scaffolds that control cellular behaviors. In this study, we investigated the osteoclast formation related to the osteoconductivity of ceramic biomaterials. We performed in vitro cocultures using osteocyte-like cells and bone marrow cells and in vivo implantations of hydroxyapatite with different amounts of carbonate substitutions into rat femurs. The analyses of the cocultures revealed that bone marrow cells differentiated into osteoclasts and were activated to resorb the substratum when grown on hydroxyapatite with higher numbers of carbonate substitutions. This was indicated by the expression of macrophage colony-stimulating factor and receptor activator of the nuclear factor-kappa B ligand that induce osteoclast differentiation by osteocyte-like cells and characteristic resorption pits. The increased osteoclastogenesis in vivo was observed near the hydroxyapatite with more carbonate substitutions after implantation into the rat femurs. These results suggest that the content of carbonate ions in an apatite crystal lattice has an inductive effect on osteoclastogenesis in the vicinity of the implanted ceramic biomaterial. The results contribute to the design of biomaterials that would be resorbed by osteoclasts after fulfilling their primary function as scaffolds for cell growth and eventually bone regeneration.

A mechanically improved virus-based hybrid scaffold for bone tissue regeneration

A hybrid scaffold (M13-phage/alginate and PCL) was proposed as a biomedical scaffold.

A superhydrophilic nitinol shape memory alloy with enhanced anti-biofouling and anti-corrosion properties

This work reports on a nitinol (NiTi) surface modification scheme based on a chemical oxidation method, and characterizes its effects on wetting, biofouling and corrosion. The scheme developed is also compared with selected previous oxidation methods. The proposed method turns NiTi into superhydrophilic in ~5 min, and the static contact angle and contact angle hysteresis were measured to be ~7° and ~12°, respectively. In the PRP (platelet rich plasma) test, platelet adhesion was reduced by ~89% and ~77% respectively, compared with the original NiTi and the NiTi treated with the previous chemical oxidation scheme. The method developed provides a high (~1.1 V) breakdown voltage, which surpasses the ASTM standard for intervascular medical devices. It also provides higher superhydrophilicity, hemo-compatibility and anti-corrosion resistance than previous oxidation schemes, with a significantly reduced process time (~5 min), and will help the development of high performance NiTi devices.

A strategy for constructing anti-adhesion surfaces based on interfacial thiol–ene photoclick chemistry between DOPA derivatives with a catechol anchor group and zwitterionic betaine macromolecules

A novel route to construct stable anti-adhesion surfaces was explored via click chemistry between the anti-adhesion macromolecules and the anchoring compound DMA to various substrates.

Electrospun fibers of chitosan-grafted polycaprolactone/poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) blends

Chitosan-grafted polycaprolactone (CS-g-PCL)/poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHH_x) fiber blends were prepared via wet electrospinning, and their morphology, hydrophilicity, water absorption, biodegradation, cytotoxicity, and thermal, mechanical and antibacterial properties were analyzed. IR spectra revealed strong H-bonding interactions between CS-g-PCL and PHBHH_x. SEM and DSC analysis confirmed the immiscibility of the blends at all compositions studied. As the proportion of CS-g-PCL increased, the overall crystallinity of the blends increased, the melting temperature of PCL decreased, and each component promoted the crystallization of the others. The hydrophilicity, water absorption and weight loss in buffered solution decreased as the PHBHH_x content increased. DMA and tensile tests indicated a synergistic effect on the mechanical properties at a blend composition of 70/30, leading to an optimal combination of stiffness, strength, ductility and toughness. The fibers retained adequate rigidity and strength under physiological conditions. The 70/30 blend exhibited the highest biocide action against Gram-positive and Gram-negative bacteria. The fibers did not induce toxicity over human dermal fibroblasts. These biodegradable, biocompatible electrospun fibers could be used as scaffolds for tissue engineering.

Protein adsorption, platelet adhesion, and bacterial adhesion to polyethylene-glycol-textured polyurethane biomaterial surfaces

Traditional strategies for surface modification to enhance the biocompatibility of biomaterials often focus on a single route utilizing either chemical or physical approaches. This study combines the chemical and physical treatments as applied to poly(urethane urea) (PUU) biomaterials to enhance biocompatibility at the interface for inhibiting platelet-related thrombosis or bacterial adhesion-induced microbial infections. PUU films were first textured with submicron patterns by a soft lithography two-stage replication process, and then were grafted with polyethylene glycol (PEG). A series of biological response experiments including protein adsorption, platelet adhesion/activation, and bacterial adhesion/biofilm formation showed that PEG-grafted submicron textured biomaterial surfaces were resistant to protein adsorption, and greatly increased the efficiency in reducing both platelet adhesion/activation and bacterial adhesion/biofilm formation due to the additive effects of physical topography and grafted PEG. Results suggest that a combination of chemical modification and surface texturing will be more efficient in preventing biomaterial-associated thrombosis and infection of biomaterials. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 668-678, 2017.

In vitro hemocompatibility on thin ceramic and hydrogel films deposited on polymer substrate performed in arterial flow conditions

Hydrogel coatings were stabilized by titanium carbonitride a-C:H:Ti:N buffer layers deposited directly onto the polyurethane (PU) substrate beneath a final hydrogel coating. Coatings of a-C:H:Ti:N were deposited using a hybrid method of pulsed laser deposition (PLD) and magnetron sputtering (MS) under high vacuum conditions. The influence of the buffer a-C:H:Ti:N layer on the hydrogel coating was analysed by means of a multi-scale microstructure study. Mechanical tests were performed at an indentation load of 5 mN using Berkovich indenter geometry. Haemocompatible analyses were performed in vitro using a blood flow simulator. The blood-material interaction was analysed under dynamic conditions. The coating fabrication procedure improved the coating stability due to the deposition of the amorphous titanium carbonitride buffer layer.

Interactions of liposomes with dental restorative materials

The in vitro adsorption and retention of liposomes onto four common types of dental restorative materials (conventional and silorane-based resin composites as well as conventional and resin-modified glass ionomer cements (GIC)) have been investigated due to their potential use in the oral cavity. Uncoated liposomes (positively and negatively charged) and pectin (low- and high-methoxylated) coated liposomes were prepared and characterized in terms of particle size and zeta potential. The adsorption of liposomes was performed by immersion, quantified by fluorescence detection, and visualized by fluorescence imaging and atomic force microscopy. Positive liposomes demonstrated the highest adsorption on all four types of materials likely due to their attractive surface charge. They also retained well (minimum 40% after 60 min) on both conventional resin composite and GIC even when exposed to simulated salivary flow. Although an intermediate initial level of adsorption was found for the pectin coated liposomes, at least 70% high methoxylated-pectin coated liposomes still remained on the conventional resin composite after 60 min flow exposure. This indicates significant contribution of hydrophobic interactions in the prolonged binding of liposomes to resin composites. Based on these results, the present paper suggests two new possible applications of liposomes in the preservation of dental restorations.

Collagen/elastin hydrogels cross-linked by squaric acid

Hydrogels based on collagen and elastin are very valuable materials for medicine and tissue engineering. They are biocompatible; however their mechanical properties and resistance for enzymatic degradation need to be improved by cross-linking. Up to this point many reagents have been tested but more secure reactants are still sought. Squaric acid (SqAc), 3,4-dihydroxy 3-cyclobutene 1,2-dione, is a strong, cyclic acid, which reacts easily with amine groups. The properties of hydrogels based on collagen/elastin mixtures (95/5, 90/10) containing 5%, 10% and 20% of SqAc and neutralized via dialysis against deionized water were tested. Cross-linked, 3-D, transparent hydrogels were created. The cross-linked materials are stiffer and more resistant to enzymatic degradation than those that are unmodified. The pore size, swelling ability and surface polarity are reduced due to 5% and 10% of SqAc addition. At the same time, the cellular response is not significantly affected by the cross-linking. Therefore, squaric acid would be regarded as a safe, effective cross-linking agent.

Shaping Nanoparticles with Hydrophilic Compositions and Hydrophobic Properties as Nanocarriers for Antibiotic Delivery

Inspired by the lotus effect in nature, surface roughness engineering has led to novel materials and applications in many fields. Despite the rapid progress in superhydrophobic and superoleophobic materials, this concept of Mother Nature's choice is yet to be applied in the design of advanced nanocarriers for drug delivery. Pioneering work has emerged in the development of nanoparticles with rough surfaces for gene delivery; however, the preparation of nanoparticles with hydrophilic compositions but with enhanced hydrophobic property at the nanoscale level employing surface topology engineering remains a challenge. Herein we report for the first time the unique properties of mesoporous hollow silica (MHS) nanospheres with controlled surface roughness. Compared to MHS with a smooth surface, rough mesoporous hollow silica (RMHS) nanoparticles with the same hydrophilic composition show unusual hydrophobicity, leading to higher adsorption of a range of hydrophobic molecules and controlled release of hydrophilic molecules. RMHS loaded with vancomycin exhibits an enhanced antibacterial effect. Our strategy provides a new pathway in the design of novel nanocarriers for diverse bioapplications.

Cytocompatibility of Si-incorporated TiO2 nanopores films

Si-incorporated TiO2 nanopores films were prepared by anodization and silicon plasma immersion ion implantation. The microstructure and phase composition of the films were investigated by scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. The hydrophilicity of the films was evaluated using water contact angle measurement and MG63 cells were cultured on the films to investigate the cytocompatibility. The results showed that the concentration and depth of silicon on the Si-incorporated TiO2 nanopores films increased with the duration time of implantation. Both the as-annealed and Si-incorporated nanopores films exhibited good hydrophilicity and cytocompatibility, while the TiO2 nanopores films implanted silicon for 1.0h showed higher proliferation rate and vitality of MG63 cells than others, indicating a great potential application for titanium implants.

Surface properties of nanocrystalline TiO2 coatings in relation to the in vitro plasma protein adsorption

This study reports on the selective adsorption of whole plasma proteins on hydrothermally (HT) grown TiO2-anatase coatings and its dependence on the three main surface properties: surface charge, wettability and roughness. The influence of the photo-activation of TiO2 by UV irradiation was also evaluated. Even though the protein adhesion onto Ti-based substrates was only moderate, better adsorption of any protein (at pH = 7.4) occurred for the most negatively charged and hydrophobic substrate (Ti non-treated) and for the most nanorough and hydrophilic surface (HT Ti3), indicating that the mutual action of the surface characteristics is responsible for the attraction and adhesion of the proteins. The HT coatings showed a higher adsorption of certain proteins (albumin 'passivation' layer, apolipoproteins, vitamin D-binding protein, ceruloplasmin, α-2-HS-glycoprotein) and higher ratios of albumin to fibrinogen and albumin to immunoglobulin γ-chains. The UV pre-irradiation affected the surface properties and strongly reduced the adsorption of the proteins. These results provide in-depth knowledge about the characterization of nanocrystalline TiO2 coatings for body implants and provide a basis for future studies on the hemocompatibility and biocompatibility of such surfaces.