Poly(lactic acid)-Mass production, processing, industrial applications, and end of life

Research progress in fully biorenewable tough blends of polylactide and green plasticizers

Plasticized PLA plastic films are being increasingly used in, among others, packaging and agriculture sectors in an attempt to address the rapid growth of municipal waste. The present paper aims to review the recent progress and the state-of-the-art in the field of fully bio-renewable tough blends of PLA with green plasticizers aimed at developing flexible packaging films. The different classes of green substances, derived from completely bio-renewable resources, used as potential plasticizers for PLA resins are reviewed. The effectiveness of these additives for PLA plasticization is discussed by describing their effects on different properties of PLA. The performance of these blends is primarily determined by the solvent power, compatibility, efficiency, and permanence of plasticizer present in the PLA matrix of resulting films. The various chemical modification strategies employed to tailor the phase interactions, dispersion level and morphology, plasticization efficiency, and permanence, including functionalization, oligomerization, polymerization and self-crosslinking, grafting and copolymerization, and dynamic vulcanization are demonstrated. Sometimes a third component has also been added to the plasticized binary blends as compatibilizer to further promote dispersion and interfacial adhesion. The impact of chemical structure, size and molecular weight, chemical functionalities, polarity, concentration, topology as well as molecular architectures of the plasticizers on the plasticizer performance and the overall characteristics of resulting plasticized PLA materials is discussed. The morphological features and toughening mechanisms for PLA/plasticizer blends are also presented. The different green liquids employed show varying degree of plasticization. Some are more useful for semi-rigid applications, while some others can be used for very flexible products. There is an optimum level of plasticizer in PLA matrices above which the tensile ductility deteriorates. Esters-derivatives of bio-based plasticizers have been shown to be very promising additives for PLA modification. Some plasticizers impart additional functions such as antioxidation and antibacterial activity to the resulting PLA materials, or compatibilization in PLA-based blends. While the primary objective of plasticization is to boost the processability, flexibility, and toughness over wider practical conditions, the bio-degradability, permeability and long-term stability of microstructure (and thereby properties) of the plasticized films against light, weathering, thermal aging, and oxidation deserve further investigations.

Ring-opening polymerization of lactide catalyzed using metal-coordinated enzyme-like amino acid assemblies

Polylactide (PLA), a biocompatible and biodegradable polymer, is widely used in diverse biomedical applications. However, the industry standard for converting lactide into PLA involves toxic tin (Sn)-based catalysts. To mitigate the use of these harmful catalysts, other environmentally benign metal-containing agents for efficient lactide polymerization have been studied, but these alternatives are hindered by complex synthesis processes, reactivity issues, and selectivity limitations. To overcome these shortcomings, we explored the catalytic activity of Cu-(Phe)2 and Zn-(Phe)2 metal-amino acid co-assemblies as potential catalysts of the ring-opening polymerization (ROP) of lactide into PLA. Catalytic activity of the assemblies was monitored at different temperatures and solvents using 1H-NMR spectroscopy to determine the catalytic parameters. Notably, Zn-(Phe)2 achieved >99% conversion of lactide to PLA within 12 h in toluene under reflux conditions and was found to have first-order kinetics, whereas Cu-(Phe)2 exhibited significantly lower catalytic activity. Following Zn-(Phe)2-mediated catalysis, the resulting PLA had an average molecular weight of 128 kDa and a dispersity index of 1.25 as determined by gel permeation chromatography. Taken together, our minimalistic approach expands the realm of metal-amino acid-based supramolecular catalytic nanomaterials useful in the ROP of lactide. This advancement shows promise for the future design of simplified biocatalysts in both industrial and biomedical applications.

Combating micro/nano plastic pollution with bioplastic: Sustainable food packaging, challenges, and future perspectives

The widespread use of plastic in food packaging provides significant challenges due to its non-biodegradability and the risk of hazardous chemicals seeping into food and the environment. This highlights the pressing need to come up with alternatives to traditional plastic that prioritize environmental sustainability, food quality, and safety. The current study presents an up-to-date examination of micro/nano plastic (MP/NP) consumption and their associated toxicity to human health, while also considering bioplastic as safer and eco-friendly alternative materials for packaging. The study contributes to a deeper comprehension of the primary materials utilized for bioplastic manufacturing and their potential for large-scale use. The key findings underscore the distinctive features of bioplastics, such as starch, polyhydroxyalkanoates, polylactic acid, and polybutylene succinate, as well as their blends with active agents, rendering them suitable for innovative food packaging applications. Moreover, the study includes a discussion of insights from various scientific literature, agency reports (governmental and non-governmental), and industry trends in bioplastic production and their potential to combat MP/NP pollution. In essence, the review highlights future research directions for the safe integration of bioplastics in food packaging, addresses outstanding questions, and proposes potential solutions to challenges linked with plastic usage.

Electrospun high hydrophilicity antimicrobial poly (lactic acid)/silk fibroin nanofiber membrane for wound dressings

Antimicrobial wound dressings can aid wound healing by preventing bacterial infection. This is particularly true of electrospun ones, which have a porous structure and can be easily loaded with antimicrobial drugs. Here, Poly lactic acid (PLA), Silk Fibroin (SF) and antimicrobial agents of Silver nanoparticles (Ag NPs) and Silver oxide (Ag2O) to prepare the PLA/SF composites antimicrobial nanofiber membrane by electrospinning. The PLA with 30 % SF nanofiber membrane show the water vapor permeability (WVP) and the liquid absorption of 36 g·mm/(m2·d·kPa) and 1721 %. With the increasing of SF contents, the degradation rate and surface hydrophilicity of the nanofiber membrane increase significantly. The nanofiber membrane exhibited excellent antimicrobial activity against Pseudomonas aeruginosa (P. aeruginosa) with the inhibition circle reach at 18.2 mm. The resultant nanofiber membrane showed high cytosolic activity, good cytocompatibility and strong antimicrobial ability, which laid a theoretical foundation for the construction of a new PLA/SF composites antimicrobial fiber membrane.

Challenges and opportunities in managing biodegradable plastic waste: A review

Biodegradable plastics have certain challenges in a waste management perspective. The existing literature reviews fail to provide a consolidated overview of different process steps of biodegradable plastic waste management and to discuss the support provided by the existing legislation for the same. The present review provides a holistic overview of these process steps and a comprehensive relative summary of 13 existing European Union (EU) laws related to waste management and circular economy, and national legislations plus source separation guidelines of 13 countries, to ensure the optimal use of resources in the future. Following were the major findings: (i) numerous types and low volumes of biodegradable plastics pose a challenge to developing cost-effective waste management infrastructure; (ii) biodegradable plastics are promoted as food-waste collection aids, but consumers are often confused about their proper disposal and are prone to greenwashing from manufacturers; (iii) industry-level studies demonstrating mechanical recycling on a full scale are unavailable; (iv) the existing EU legislation dealt with general topics related to biodegradable plastics; however, only the new proposal on plastic packaging waste and the EU policy framework for bioplastics clearly mentioned their disposal and (v) clear disparities were observed between disposal methods suggested by national legislation and available source separation guidelines. Thus, to appropriately manage biodegradable plastic waste, it is necessary to develop waste processing and material utilization infrastructure as well as create consumer awareness. In the end, recommendations were provided for improved biodegradable plastic waste management from the perspective of systemic challenges identified from the literature review.

Opacification Kinetics of PLA during Liquid Water Sorption

When in contact with water, poly(lactic acid), PLA, undergoes several physical changes. A very evident one is opacification, namely the change from the typical transparent appearance to a white opaque color. This phenomenon is particularly significant for many applications, including packaging, since opacity hinders the possibility of a clear look of the packed goods and also worsens the consumers' perceptions. In this work, we report an analysis of the time evolution of the phenomenon in different conditions of temperature and water concentration. The results allow us to define a time-scale of the phenomenon and to put it in relationship with the temperature and water content inside the material. In particular, opacification proceeds from the outer surface of the specimens toward the center. Both craze formation due to hydrolysis and crystallization contribute to the opacification phenomenon. Opacification becomes faster as temperature increases, whereas the increase in the solution density has the opposite effect. A model for describing the evolution of opacification was proposed and found to be consistent with the experimental data.

Interaction of Micro- and Nanoplastics with Enzymes: The Case of Carbonic Anhydrase

Microplastics (MPs) and nanoplastics (NPs) have emerged as significant environmental pollutants with potential detrimental effects on ecosystems and human health. Several studies indicate their interaction with enzymes; this topic represents a multifaceted research field encompassing several areas of interest from the toxicological and ecotoxicological impact of MPs and NPs on humans and wildlife to the biodegradation of plastics by microbial enzymes. This review aims to provide a critical analysis of the state-of-the-art knowledge of the interaction of MPs and NPs on the enzyme carbonic anhydrase (CA), providing recent insights, analyzing the knowledge gaps in the field, and drawing future perspectives of the research and its application. CA is a widespread and crucial enzyme in various organisms; it is critical for various physiological processes in animals, plants, and bacteria. It catalyzes the reversible hydration of CO2, which is essential for respiration, acid-base balance, pH homeostasis, ion transport, calcification, and photosynthesis. Studies demonstrate that MPs and NPs can inhibit CA activity with mechanisms including adsorption to the enzyme surface and subsequent conformational changes. In vitro and in silico studies highlight the role of electrostatic and hydrophobic interactions in these processes. In vivo studies present mixed results, which are influenced by factors like particle type, size, concentration, and organism type. Moreover, the potentiality of the esterase activity of CA for plastic degradation is discussed. The complexity of the interaction between CA and MPs/NPs underscores the need for further research to fully understand the ecological and health impacts of MPs and NPs on CA activity and expression and glimpses of the potentiality and perspectives in this field.

Aluminium complexes of phenoxy-azo ligands in the catalysis of rac-lactide polymerisation

Fourteen new phenoxy-azo aluminium complexes comprising two series, namely, dimethyl{phenoxy-azo}aluminium complexes 1a-7a and monomethyl{phenoxy-azo}aluminium complexes 1b-7b, were successfully synthesised and characterised. The molecular structure of complex 4a, determined using X-ray diffraction analysis, displayed a distorted tetrahedral geometry. The 1H NMR spectrum of complex 5b revealed fluxional behaviour caused by isomeric transformation that occurs in the solution at room temperature. The activation parameters determined by lineshape analysis of variable-temperature 1H NMR spectra in toluene-d8 are as follows: ΔH‡ = 70.05 ± 1.19 kJ mol-1, ΔS‡ = 21.78 ± 3.58 J mol-1 K-1 and ΔG‡ (298 K) = 63.56 ± 0.11 kJ mol-1. All aluminium complexes are active initiators for the ring-opening polymerisation of rac-lactide, and the polymerisations proceeded in a controlled manner and were living. In comparison, the catalytic activity of the dimethyl{phenoxy-azo}aluminium complexes was insignificantly different from that of the corresponding monomethyl{phenoxy-azo}aluminium complexes. The steric factor of the ortho-phenoxy substituent was observed to exert a decelerating effect on the catalytic rate. Kinetic investigations revealed first-order dependency on both monomer and initiator concentrations. Comparative catalytic investigations conducted on phenoxy-azo aluminium and phenoxy-imine aluminium complexes revealed that the former complexes exhibited lower catalytic activity.

Effect of Surface Contamination on Near-Infrared Spectra of Biodegradable Plastics

Proper waste sorting is crucial for biodegradable plastics (BDPs) recycling, whose global production is increasing dynamically. BDPs can be sorted using near-infrared (NIR) sorting, but little research is available about the effect of surface contamination on their NIR spectrum, which affects their sortability. As BDPs are often heavily contaminated with food waste, understanding the effect of surface contamination is necessary. This paper reports on a study on the influence of artificially induced surface contamination using food waste and contamination from packaging waste, biowaste, and residual waste on the BDP spectra. In artificially contaminated samples, the absorption bands (ADs) changed due to the presence of moisture (1352-1424 nm) and fatty acids (1223 nm). In real-world contaminated samples, biowaste samples were most affected by contamination followed by residual waste, both having altered ADs at 1352-1424 nm (moisture). The packaging waste-contaminated sample spectra closely followed those of clean and washed samples, with a change in the intensity of ADs. Accordingly, two approaches could be followed in sorting: (i) affected wavelength ranges could be omitted, or (ii) contaminated samples could be used for optimizing the NIR database. Thus, surface contamination affected the spectra, and knowing the wavelength ranges containing this effect could be used to optimize the NIR database and improve BDP sorting.

Synergistic effect of TiO2 nanoparticles and poly (ethylene-co-vinyl acetate) on the morphology and crystallization behavior of polylactic acid

The impact of adding ethylene vinyl acetate copolymer (EVA 80) and 1 wt% TiO2 nanoparticles on the morphology and crystallization behavior of poly(lactic acid) blends was investigated using DSC, SEM, and POM. Thermal analysis revealed the enhancement of crystallinity of PLA in the presence of TiO2 and higher EVA 80 content in the blend. The PLA and EVA 80 components showed compatibility, as evidenced by the shift of the glass transition temperatures of the PLA phase in the blend to lower values compared to neat PLA. The lower temperature shift of the cold crystallization of the PLA and the formation of the small spherulites of the PLA in the blends indicated that the EVA 80 and TiO2 act as a nucleating agent for crystallization. The non-isothermal crystallization parameters of the composites were evaluated using Avrami's modified model, the MO approach, and Friedman's isoconversional method. The Avrami's modified rate constant (K) and the effective activation energy values significantly increased with the incorporation of EVA 80 and TiO2 nanoparticles. Furthermore, the thermogravimetric analysis (TGA) showed improved thermal stability of PLA by adding EVA 80 and TiO2.

Superhydrophobic stereocomplex-type polylactide/ultra-fine glass fibers aerogel for passive daytime radiative cooling

Passive daytime radiative cooling (PDRC) technology offers a green and sustainable strategy for cooling, eliminating the need for external energy sources through its exceptional efficiency in heat radiation and sunlight reflection. Despite its benefits, the widespread usage of non-biodegradable PDRC materials has unfortunately caused environmental pollution and resource wastage. Furthermore, the effectiveness of outdoor PDRC materials can be significantly diminished by rainfall. In this work, a superhydrophobic composite aerogel composed of stereocomplex-type polylactide and ultra-fine glass fiber has been successfully developed through simple physical blending and freeze-drying, which exhibits low thermal conductivity (36.26 mW m-1 K-1) and superhydrophobicity (water contact angle up to 150°). Additionally, its high solar reflectance (91.68 %) and strong infrared emissivity (93.95 %) enable it to effectively lower surface temperatures during daytime, resulting in a cooling effect of approximately 3.8 °C below the ambient temperature during the midday heat of summer, with a cooling power of 68 W/m2. This aerogel offers an environmentally friendly and sustainable approach for the utilization of radiative refrigeration materials, paving the way for environmental protection and sustainable development.

Chemically Programmed Hydrogels for Spatiotemporal Modulation of the Cardiac Pathological Microenvironment

After myocardial infarction (MI), sustained ischemic events induce pathological microenvironments characterized by ischemia-hypoxia, oxidative stress, inflammatory responses, matrix remodeling, and fibrous scarring. Conventional clinical therapies lack spatially targeted and temporally responsive modulation of the infarct microenvironment, leading to limited myocardial repair. Engineered hydrogels have a chemically programmed toolbox for minimally invasive localization of the pathological microenvironment and personalized responsive modulation over different pathological periods. Chemically programmed strategies for crosslinking interactions, interfacial binding, and topological microstructures in hydrogels enable minimally invasive implantation and in situ integration tailored to the myocardium. This enhances substance exchange and signal interactions within the infarcted microenvironment. Programmed responsive polymer networks, intelligent micro/nanoplatforms, and biological therapeutic cues contribute to the formation of microenvironment-modulated hydrogels with precise targeting, spatiotemporal control, and on-demand feedback. Therefore, this review summarizes the features of the MI microenvironment and chemically programmed schemes for hydrogels to conform, integrate, and modulate the cardiac pathological microenvironment. Chemically programmed strategies for oxygen-generating, antioxidant, anti-inflammatory, provascular, and electrointegrated hydrogels to stimulate iterative and translational cardiac tissue engineering are discussed.

Thermal, Morphological, Mechanical, and Biodegradation Properties of Poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide)/High-Density Polyethylene Blends

Polymer blends of poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) (PLLA-PEG-PLLA) and high-density polyethylene (HDPE) with different blend ratios were prepared by a melt blending method. The thermal, morphological, mechanical, opacity, and biodegradation properties of the PLLA-PEG-PLLA/HDPE blends were investigated and compared to the PLLA/HDPE blends. The blending of HDPE improved the crystallization ability and thermal stability of the PLLA-PEG-PLLA; however, these properties were not improved for the PLLA. The morphology of the blended films showed that the PLLA-PEG-PLLA/HDPE blends had smaller dispersed phases compared to the PLLA/HDPE blends. The PLLA-PEG-PLLA/HDPE blends exhibited higher flexibility, lower opacity, and faster biodegradation and bioerosion in soil than the PLLA/HDPE blends. Therefore, these PLLA-PEG-PLLA/HDPE blends have a good potential for use as flexible and partially biodegradable materials.

Melt Compounding of Poly(lactic acid)-Based Composites: Blending Strategies, Process Conditions, and Mechanical Properties

Polylactic acid (PLA), derived from renewable resources, has the advantages of rigidity, thermoplasticity, biocompatibility, and biodegradability, and is widely used in many fields such as packaging, agriculture, and biomedicine. The excellent processability properties allow for melt processing treatments such as extrusion, injection molding, blow molding, and thermoforming in the preparation of PLA-based materials. However, the low toughness and poor thermal stability of PLA limit its practical applications. Compared with pure PLA, conditions such as processing technology, filler, and crystallinity affect the mechanical properties of PLA-based materials, including tensile strength, Young's modulus, and elongation at break. This review systematically summarizes various technical parameters for melt processing of PLA-based materials and further discusses the mechanical properties of PLA homopolymers, filler-reinforced PLA-based composites, PLA-based multiphase composites, and reactive composite strategies for PLA-based composites.

Deterioration of bio-based polylactic acid plastic teabags under environmental conditions and their associated effects on earthworms

In response to the plastic waste crisis, teabag producers have substituted the petrochemical-plastic content of their products with bio-based, biodegradable polymers such as polylactic acid (PLA). Despite widespread use, the degradation rate of PLA/PLA-blended materials in natural soil and their effects on soil biota are poorly understood. This study examined the percentage mass deterioration of teabags with differing cellulose:PLA compositions following burial (-10 cm depth) in an arable field margin for 7-months, using a suite of analytical techniques, such as size exclusion chromatography, 1H nuclear magnetic resonance, dynamic scanning calorimetry, and scanning electron microscopy. The effect of 28-d exposure to teabag discs at environmentally relevant concentrations (0.02 %, 0.04 % and 0.07 % w/w) on the survival, growth and reproduction (OECD TG 222 protocol) of the key soil detritivore Eisenia fetida was assessed in laboratory trials. After 7-month burial, Tbag-A (2.4:1 blend) and Tbag-B (3.5:1 cellulose:PLA blend) lost 66 ± 5 % and 78 ± 4 % of their total mass, primarily attributed to degradation of cellulose as identified by FTIR spectroscopy and a reduction in the cellulose:PLA mass ratio, while Tbag-C (PLA) remained unchanged. There were clear treatment and dose-specific effects on the growth and reproductive output of E. fetida. At 0.07 % w/w of Tbag-A adult mortality marginally increased (15 %) and both the quantity of egg cocoons and the average mass of juveniles also increased, while at concentrations ≥0.04 % w/w of Tbag-C, the quantity of cocoons was suppressed. Adverse effects are comparable to those reported for non-biodegradable petrochemical-based plastic, demonstrating that bio-based PLA does not offer a more 'environmentally friendly' alternative. Our study emphasises the necessity to better understand the environmental fate and ecotoxicity of PLA/PLA-blends to ensure interventions developed through the UN Plastic Pollution Treaty to use alternatives and substitutes to conventional plastics do not result in unintended negative consequences.

Biodegradable biopolymers: Real impact to environment pollution

Biobased biodegradable polymers (BBP) derived from different renewable resources are commonly considered as attractive alternative to petroleum-based polymers, such as polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), etc. It is because they can address the issues of serious environmental problems resulted from accumulation of plastic wastes. In the review current methods of obtaining of most abundant BBP, polylactic acid (PLA) and polyhydroxybutyrate (PHB), have been studied with an emphasis on the toxicity of compounds used for their production and additives improving consumer characteristics of PLA and PHB based market products. Substantial part of additives was the same used for traditional polymers. Analysis of the data on the response of different organisms and plants on exposure to these materials and their degradation products confirmed the doubts about real safety of BBP. Studies of safer additives are scarce and are of vital importance. Meanwhile, technologies of recycling of traditional petroleum-based polymers were shown to be well-developed, which cannot be said about PLA or PHB based polymers, and their blends with petroleum-based polymers. Therefore, development of more environmentally friendly components and sustainable technologies of production are necessary before following market expansion of biobased biodegradable products.

An engineered enzyme embedded into PLA to make self-biodegradable plastic

Plastic production reached 400 million tons in 2022 (ref. 1), with packaging and single-use plastics accounting for a substantial amount of this2. The resulting waste ends up in landfills, incineration or the environment, contributing to environmental pollution3. Shifting to biodegradable and compostable plastics is increasingly being considered as an efficient waste-management alternative4. Although polylactide (PLA) is the most widely used biosourced polymer5, its biodegradation rate under home-compost and soil conditions remains low6-8. Here we present a PLA-based plastic in which an optimized enzyme is embedded to ensure rapid biodegradation and compostability at room temperature, using a scalable industrial process. First, an 80-fold activity enhancement was achieved through structure-based rational engineering of a new hyperthermostable PLA hydrolase. Second, the enzyme was uniformly dispersed within the PLA matrix by means of a masterbatch-based melt extrusion process. The liquid enzyme formulation was incorporated in polycaprolactone, a low-melting-temperature polymer, through melt extrusion at 70 °C, forming an 'enzymated' polycaprolactone masterbatch. Masterbatch pellets were integrated into PLA by melt extrusion at 160 °C, producing an enzymated PLA film (0.02% w/w enzyme) that fully disintegrated under home-compost conditions within 20-24 weeks, meeting home-composting standards. The mechanical and degradation properties of the enzymated film were compatible with industrial packaging applications, and they remained intact during long-term storage. This innovative material not only opens new avenues for composters and biomethane production but also provides a feasible industrial solution for PLA degradation.

Optimization of Laminated Bio-Polymer Fabrication for Food Packaging Application: A Sustainable Plasma-Activated Approach

The current level of packaging consumption imposes a need to fabricate single-use food packaging with renewable and compostable materials, such as bio-polyesters (e.g., polylactic acid, PLA and polybutylene succinate, PBS) or cellulose, but their use is still problematic. Fabrication of bio-compostable composites can specifically address impeding challenges, and adhesive lamination, achieved with compostable glue, is becoming more and more popular with respect to the less versatile hot lamination. In this context, plasma activation, a chemical-free oxidation technique of a material's surface, is used to increase the affinity of three different biomaterials (cellulose, PLA and PBS) toward a compostable polyurethane adhesive to decrease its amount by gluing bio-polyesters to cellulose. Optical Microscopy reveals activation conditions that do not affect the integrity of the materials, while Water Contact Analyses confirm the activation of the surfaces, with contact angles decreased to roughly 50 deg in all cases. Unexpectedly, ζ-potential analyses and subtractive infrared spectroscopy highlight how the activation performed superficially etches cellulose, while for both PLA and PBS, a general decrease in surface potential and an increase in superficial hydroxyl group populations confirm the achievement of the desired oxidation. Thus, we rationalize continuous activation conditions to treat PLA and PBS and to glue them to neat cellulose. While no beneficial effect is observed with activated PLA, bi-laminate composites fabricated with activated PBS fulfill the benchmark for adhesion strength using less than before, while oxygen permeation analyses exclude plasma-induced etching even at a nanoscale.

A robust and biodegradable hydroxyapatite/poly(lactide-co-ε-caprolactone) electrospun membrane for dura repair

Typically occurring after trauma or neurosurgery treatments, dura mater defect and the ensuing cerebrospinal fluid (CSF) leakage could lead to a number of serious complications and even patient's death. Although numerous natural and synthetic dura mater substitutes have been reported, none of them have been able to fulfill the essential properties, such as anti-adhesion, leakage blockage, and pro-dura rebuilding. In this study, we devised and prepared a series of robust and biodegradable hydroxyapatite/poly(lactide-co-ε-caprolactone) (nHA/PLCL) membranes for dura repair via an electrospinning technique. In particular, PLLA/PCL (80/20) was selected for electrospinning due to its mechanical properties that most closely resembled natural dural tissue. Studies by SEM, XRD, water contact angle and in vitro degradation showed that the introduction of nHA would destroy PLCL's crystalline structure, which would further affect the mechanical properties of the nHA/PLCL membranes. When the amount of nHA added increased, so did the wettability and in vitro degradation rate, which accelerated the release of nHA. In addition, the high biocompatibility of nHA/PLCL membranes was demonstrated by in vitro cytotoxicity data. The in vivo rabbit dura repair model results showed that nHA/PLCL membranes provided a strong physical barrier to stop tissue adhesion at dura defects. Meanwhile, the nHA/PLCL and commercial group's CSF had a significantly lower number of inflammatory cells than the control groups, validating the nHA/PLCL's ability to effectively lower the risk of intracranial infection. Findings from H&E and Masson-trichrome staining verified that the nHA/PLCL electrospun membrane was more favorable for fostering dural defect repair and skull regeneration. Moreover, the relative molecular weight of PLCL declined dramatically after 3 months of implantation, according to the results of the in vivo degradation test, but it retained the fiber network structure and promoted tissue growth, demonstrating the good stability of the nHA/PLCL membranes. Collectively, the nHA/PLCL electrospun membrane presents itself as a viable option for dura repair.

Preparation of Poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide)/Zinc Oxide Nanocomposite Bioplastics for Potential Use as Flexible and Antibacterial Food Packaging

High-molecular-weight poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) (PLLA-PEG-PLLA) is a flexible and biodegradable bioplastic that has promising potential in flexible food packaging but it has no antibacterial ability. Thus, in this work, the effect of zinc oxide nanoparticles (nano-ZnOs) which have antimicrobial activity on various properties of PLLA-PEG-PLLA was determined. The addition of nano-ZnOs enhanced the crystallization, tensile, UV-barrier, and antibacterial properties of PLLA-PEG-PLLA. However, the crystallization and tensile properties of nanocomposite films decreased again as the nano-ZnO increased beyond 2 wt%. The nano-ZnO was well distributed in the PLLA-PEG-PLLA matrix when the nano-ZnO content did not exceed 2 wt% and exhibited some nano-ZnO agglomerates when the nano-ZnO content was higher than 2 wt%. The thermal stability and moisture uptake of the PLLA-PEG-PLLA matrix decreased and the film's opacity increased as the nano-ZnO content increased. The PLLA-PEG-PLLA/ZnO nanocomposite films showed good antibacterial activity against bacteria such as Escherichia coli and Staphylococcus aureus. It can be concluded that nano-ZnOs can be used as a multi-functional filler of the flexible PLLA-PEG-PLLA. As a result, the addition of nano-ZnOs as a nucleating, reinforcing, UV-screening, and antibacterial agent in the flexible PLLA-PEG-PLLA matrix may provide protection for both the food and the packaging during transportation and storage.

A Comparison of Laboratory and Industrial Processes Reveals the Effect of Dwell Time and UV Pre-Exposure on the Behavior of Two Polymers in a Disintegration Trial

Biodegradable biopolymers such as polylactic acid and polybutylene succinate are sustainable alternatives to traditional petroleum-based plastics. However, the factors affecting their degradation must be characterized in detail to enable successful utilization. Here we compared the extruder dwell time at three different melt-spinning scales and its influence on the degradation of both polymers. The melt temperature was the same for all three processes, but the shear stress and dwell time were key differences, with the latter being the easiest to measure. Accelerated degradation tests, including quick weathering and disintegration, were used to evaluate the influence of dwell time on the structural, mechanical, and thermal properties of the resulting fibers. We found that longer dwell times accelerated degradation. Quick weathering by UV pre-exposure before the disintegration trial, however, had a more significant effect than dwell time, indicating that degradation studies with virgin material in a laboratory-scale setting only show the theoretical behavior of a product in the laboratory. A weathered fiber from an industrial-scale spinning line more accurately predicts the behavior of a product placed on the market before ending up in the environment. This highlights the importance of optimizing process parameters such as the dwell time to adapt the degradability of biopolymers for specific applications and environmental requirements. By gaining a deeper insight into the relationship between manufacturing processes and fiber degradability, products can be adapted to meet suitable performance criteria for different applications.

Poly(butylene oxalate-co-terephthalate): A PBAT-like but rapid hydrolytic degradation plastic

Concerns over worldwide plastic pollution have led to the development of biodegradable polyester materials with excellent physical and chemical properties through the copolymerization of poly(butylene oxalate) (PBOx). As a result, poly(butylene oxalate-co-terephthalate)s (PBOTs) with varying compositions, were prepared by incorporating aromatic units. Studies have indicated that PBOT-47 (with a 47% molar terephthalate), exhibits exceptional mechanical properties. With an elongation at break of 1160% and a tensile strength that remains above 30 MPa, similar to or even better than those of the commercial biodegradable plastic poly(butylene adipate-co-terephthalate) PBAT-47 (47% molar terephthalate). Moreover, the permeability coefficients of PBAT-47 for H2O, CO2 and O2 were 5.8, 50.6 and 5.6 times higher than that of PBOT-47, revealing the superior barrier properties of PBOT. Through experimental research and theoretical simulation, the mechanism of the copolymer hydrolysis was elucidated. The readily hydrolytic nature of the oxalate unit endows it with the capacity for rapid degradation, possessing the potential to be a short-term degradable material with physical properties similar to PBAT.

Long-Term Thermal Stabilization of Poly(Lactic Acid)

To use polylactic acid in demanding technical applications, sufficient long-term thermal stability is required. In this work, the thermal aging of polylactic acid (PLA) in the solid phase at 100 °C and 150 °C is investigated. PLA has only limited aging stability without the addition of stabilizers. Therefore, the degradation mechanism in thermal aging was subsequently investigated in more detail to identify a suitable stabilization strategy. Investigations using nuclear magnetic resonance spectroscopy showed that, contrary to expectations, even under thermal aging conditions, hydrolytic degradation rather than oxidative degradation is the primary degradation mechanism. This was further confirmed by the investigation of suitable stabilizers. While the addition of phenols, phosphites and thioethers as antioxidants leads only to a limited improvement in aging stability, the addition of an additive composition to provide hydrolytic stabilization results in extended durability. Efficient compositions consist of an aziridine-based hydrolysis inhibitor and a hydrotalcite co-stabilizer. At an aging temperature of 100 °C, the time until significant polymer chain degradation occurs is extended from approx. 500 h for unstabilized polylactic acid to over 2000 h for stabilized polylactic acid.

Green processing via surface diffuse atmospheric plasma to enhance the dyeing performance on polylactic acid fabric

Poor dyeing performance has been a major defect of polylactic acid (PLA) fibers, which is caused by the lack of active chemical groups in PLA, and hinders the widespread use of this biodegradable material. Most of the existing chemical modification methods are not environmentally friendly and produce effluents. Herein, we report a green, efficient and continuous method to process PLA fibers via surface diffuse atmospheric plasma for the improvement of its hydrophilicity and dyeing performance. PLA fibers were processed via atmospheric plasma for grafting oxygen-containing functional groups, such as carboxyl, to achieve hydrophilicity and, meanwhile, strengthen the binding interactions with various dye molecules via covalent bonds, ionic bonds, or hydrogen bonds. In addition, different mechanisms of improving the dyeing performance on plasma-modified PLA fibers with different kinds of dyes have been discussed. This approach of material modification involves no chemical additives and has high processing efficiency, showing the potential applicability of green treatment to products in various fields.

The Influence of Environmental Factors on the Degradation of PLA/Diatomaceous Earth Composites

In the present study, tests were carried out on composite samples on a polylactide matrix containing 25% by weight of mineral filler in the form of diatomaceous earth, base, and silanized with GPTMOS (3-glycidoxypropyltrimethoxysilane), OTES (n-octyltriethoxysilane), and MTMOS (methyltrimethoxysilane) silanes. The addition of two types of waxes, synthetic polyamide wax and natural beeswax, were used as a factor to increase the rheological properties of the composites. The obtained samples were characterized in terms of the effect of filler silanization on the degradation rate of the composites. The tests were conducted under different conditioning conditions, i.e., after exposure to strong UV radiation for 250 and 500 h, and under natural sunlight for 21 days. The conditioning carried out under natural conditions showed that the modified samples exhibit up to twice the degradation rate of pure polylactide. The addition of synthetic wax to the composites increases the tendency to agglomerate diatomaceous earth, while natural wax has a positive effect on filler dispersion. For composites modified with GPTMOS and OTES silanes, it was noted that the addition of natural wax inhibited the degree of surface degradation, compared to the addition of synthetic wax, while the addition of MTMOS silane caused the opposite effect and samples with natural wax degraded more strongly. It was shown that, despite the high degree of surface degradation, the process does not occur significantly deep into the composite and stops at a certain depth.

Synthesis of Novel Polymers with Biodegradability by Main-Chain Editing of Chiral Polyketones

Although the use of biodegradable plastics is suitable for unrecoverable, single-use plastic, their high production cost and much lower variety compared to commodity plastics limit their application. In this study, we developed a new polymer with potential biodegradability, poly(ketone/ester), synthesized from propylene and carbon monoxide. Propylene and carbon monoxide are easily available at low costs from fossil resources, and they can also be derived from biomass. Using an atom insertion reaction to the main chain of the polymer, the main-chain editing of the polymer molecule proceeded with up to 89% selectivity for atom insertion over main-chain cleavage.

Synthetic Degradable Polyvinyl Alcohol Polymer and Its Blends with Starch and Cellulose-A Comprehensive Overview

Approximately 50% of global plastic wastes are produced from plastic packaging, a substantial amount of which is disposed of within a few minutes of its use. Although many plastic types are designed for single use, they are not always disposable. It is now widely acknowledged that the production and disposal of plastics have led to a plethora of negative consequences, including the contamination of both groundwater and soil resources and the deterioration of human health. The undeniable impact of excessive plastic manufacturing and waste generation on the global plastic pollution crisis has been well documented. Therefore, degradable polymers are a crucial solution to the problem of the non-degradation of plastic wastes. The disadvantage of degradable polymers is their high cost, so blending them with natural polymers will reduce the cost of final products and maximize their degradation rate, making degradable polymers competitive with industrial polymers that are currently in use daily. In this work, we will delineate various degradable polymers, including polycaprolactone, starch, and cellulose. Furthermore, we will elucidate several aspects of polyvinyl alcohol (PVA) and its blends with natural polymers to show the effects of adding natural polymers on PVA properties. This paper will study cost-effective and ecologically acceptable polymers by combining inexpensive natural polymers with readily accessible biodegradable polymers such as polyvinyl alcohol (PVA).

Recent advances in extruded polylactic acid-based composites for food packaging: A review

This review article provides a comprehensive overview of recent progress in polylactic acid (PLA) extrusion, emphasizing its applications in food packaging. PLA has witnessed a significant rise in demand, particularly within the food packaging sector. A notable increase in research publications has been observed in recent years, exploring the extrusion of PLA and PLA-based composite films. In comparison to conventional techniques such as solvent casting, extrusion offers advantages in scalability and environmental sustainability, especially for industrial-scale production. The benefits of this method include faster drying times, enhanced flexibility, consistent film thickness, and less structural defects. Extensive research has focused on the effect of various PLA blends on film properties, including flexibility, elongation, and barrier properties against water vapour and gases. Furthermore, the incorporation of compounds such as antioxidants, antimicrobials, and natural pigments has enabled the development of active and intelligent PLA-based packaging. This article summarizes the types of additives employed to enhance the physicochemical properties of extruded PLA and film performance. Additionally, this article explores the diverse applications of extruded PLA in active and intelligent packaging for various food products.

Modification of poly(lactate) via polymer blending with microbially produced poly[(R)-lactate-co-(R)-3-hydroxybutyrate] copolymers

This study investigated the effect of polymer blending of microbially produced poly[(R)-lactate-co-(R)-3-hydroxybutyrate] copolymers (LAHB) with poly(lactate) (PLA) on their mechanical, thermal, and biodegradable properties. Blending of high lactate (LA) content and high molecular weight LAHB significantly improved the tensile elongation of PLA up to more than 250 % at optimal LAHB composition of 20-30 wt%. Temperature-modulated differential scanning calorimetry and dynamic mechanical analysis revealed that PLA and LAHB were immiscible but interacted with each other, as indicated by the mutual plasticization effect. Detailed morphological characterization using scanning probe microscopy, small-angle X-ray scattering, and solid-state NMR confirmed that PLA and LAHB formed a two-phase structure with a characteristic length scale as small as 20 nm. Because of mixing in this order, the polymer blends were optically transparent. The biological oxygen demand test of the polymer blends in seawater indicated an enhancement of PLA biodegradation during biodegradation of the polymer blends.

Recyclable and (Bio)degradable Polyesters in a Circular Plastics Economy

Polyesters carrying polar main-chain ester linkages exhibit distinct material properties for diverse applications and thus play an important role in today's plastics economy. It is anticipated that they will play an even greater role in tomorrow's circular plastics economy that focuses on sustainability, thanks to the abundant availability of their biosourced building blocks and the presence of the main-chain ester bonds that can be chemically or biologically cleaved on demand by multiple methods and thus bring about more desired end-of-life plastic waste management options. Because of this potential and promise, there have been intense research activities directed at addressing recycling, upcycling or biodegradation of existing legacy polyesters, designing their biorenewable alternatives, and redesigning future polyesters with intrinsic chemical recyclability and tailored performance that can rival today's commodity plastics that are either petroleum based and/or hard to recycle. This review captures these exciting recent developments and outlines future challenges and opportunities. Case studies on the legacy polyesters, poly(lactic acid), poly(3-hydroxyalkanoate)s, poly(ethylene terephthalate), poly(butylene succinate), and poly(butylene-adipate terephthalate), are presented, and emerging chemically recyclable polyesters are comprehensively reviewed.

Potential safety concerns of volatile constituents released from coffee-ground-blended single-use biodegradable drinking straws: A chemical space perspective

Incorporating spent coffee grounds into single-use drinking straws for enhanced biodegradability also raises safety concerns due to increased chemical complexity. Here, volatile organic compounds (VOCs) present in coffee ground straws (CGS), polylactic acid straws (PLAS), and polypropylene straws (PPS) were characterized using headspace - solid-phase microextraction and migration assays, by which 430 and 153 VOCs of 10 chemical categories were identified by gas chromatography - mass spectrometry, respectively. Further, the VOCs were assessed for potential genetic toxicity by quantitative structure-activity relationship profiling and estimated daily intake (EDI) calculation, revealing that the VOCs identified in the CGS generally triggered the most structural alerts of genetic toxicity, and the EDIs of 37.9% of which exceeded the threshold of 0.15 μg person-1 d-1, also outnumbering that of the PLAS and PPS. Finally, 14 VOCs were prioritized due to their definite hazards, and generally higher EDIs or detection frequencies in the CGS. Meanwhile, the probability of producing safer CGS was also illustrated. Moreover, it was uncovered by chemical space that the VOCs with higher risk potentials tended to gather in the region defined by the molecular descriptor related to electronegativity or octanol/water partition coefficient. Our results provided valuable references to improve the chemical safety of the CGS, to promote consumer health, and to advance the sustainable development of food contact materials.

Effect of Plasticization/Annealing on Thermal, Dynamic Mechanical, and Rheological Properties of Poly(Lactic Acid)

This study investigates the use of low molecular weight poly(ethylene glycol) (PEG) as a plasticizer for poly(lactic acid) (PLA). PLA/PEG blend films were prepared using the solvent casting method with varying mixing ratios. The films were analyzed using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and dynamic rheological analysis. The results indicate that the addition of PEG as a plasticizer affects the thermal and mechanical properties of the PLA/PEG blend films. The study found that the glass transition and cold crystallization temperatures decreased with increasing PEG content up to 20 wt%, while the crystallinity and crystallization rate increased. The blends with up to 20 wt% PEG were miscible, but phase separation occurred when the plasticizer content was increased to 30 wt%. Subsequently, amorphous samples of neat PLA and PLA plasticized with 10 wt% of PEG underwent annealing at various temperatures (Ta = 80-120 °C) for durations ta of 1 and 24 h. The samples were then analyzed using DSC and DMA. The addition of PEG to PLA altered the content of α' and α crystalline forms compared to neat PLA at a given (Ta; ta) and favored the formation of a mixture of α' and α crystals. The crystallinity achieved upon annealing increased with increasing Ta or ta and with the incorporation of PEG.

Improvement in Crystallization, Thermal, and Mechanical Properties of Flexible Poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) Bioplastic with Zinc Phenylphosphate

Poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) (PLLA-PEG-PLLA) shows promise for use in bioplastic applications due to its greater flexibility over PLLA. However, further research is needed to improve PLLA-PEG-PLLA's properties with appropriate fillers. This study employed zinc phenylphosphate (PPZn) as a multi-functional filler for PLLA-PEG-PLLA. The effects of PPZn addition on PLLA-PEG-PLLA characteristics, such as crystallization and thermal and mechanical properties, were investigated. There was good phase compatibility between the PPZn and PLLA-PEG-PLLA. The addition of PPZn improved PLLA-PEG-PLLA's crystallization properties, as evidenced by the disappearance of the cold crystallization temperature, an increase in the crystallinity, an increase in the crystallization temperature, and a decrease in the crystallization half-time. The PLLA-PEG-PLLA's thermal stability and heat resistance were enhanced by the addition of PPZn. The PPZn addition also enhanced the mechanical properties of the PLLA-PEG-PLLA, as demonstrated by the rise in ultimate tensile stress and Young's modulus. We can conclude that the PPZn has potential for use as a multi-functional filler for the PLLA-PEG-PLLA composite due to its nucleating-enhancing, thermal-stabilizing, and reinforcing ability.

Fabrication of multifunctional ethyl cellulose/gelatin-based composite nanofilm for the pork preservation and freshness monitoring

In this study, an active and intelligent nanofilm for monitoring and maintaining the freshness of pork was developed using ethyl cellulose/gelatin matrix through electrospinning, with the addition of natural purple sweet potato anthocyanin. The nanofilm exhibited discernible color variations in response to pH changes, and it demonstrated a higher sensitivity towards volatile ammonia compared with casting film. Notably, the experimental findings regarding the wettability and pH response performance indicated that the water contact angle between 70° and 85° was more favorable for the smart response of pH sensitivity. Furthermore, the film exhibited desirable antioxidant activities, water vapor barrier properties and also good antimicrobial activities with the incorporation of ε-polylysine, suggesting the potential as a food packaging film. Furthermore, the application preservation outcomes revealed that the pork packed with the nanofilm can prolong shelf life to 6 days, more importantly, a distinct color change aligned closely with the points indicating the deterioration of the pork was observed, changing from light pink (indicating freshness) to light brown (indicating secondary freshness) and then to brownish green (indicating spoilage). Hence, the application of this multifunctional film in intelligent packaging holds great potential for both real-time indication and efficient preservation of the freshness of animal-derived food items.

Structure and properties of chlorogenic acid-loaded polylactide fiber prepared by melt spinning

Polylactide/chlorogenic acid (PLA/CGA) blends with different weight ratios were prepared by melt mixing, and corresponding PLA/CGA fibers were produced via a two-step melt spinning process. For PLA/CGA blends, CGA was distributed uniformly in the PLA matrix. The intermolecular interactions between CGA and PLA existed. The viscosity of PLA/CGA blends was much lower than that of neat PLA. With the increase of CGA content, the viscosity of PLA/CGA blends decreased. As the CGA content increased, the crystallinity of both PLA/CGA blends and fibers decreased. In addition, the tensile strength of PLA/CGA fibers was slightly lower than that of neat PLA fiber. For PLA/CGA fibers, the 6-fold drawn PLA/CGA fiber with 3 % CGA owned the highest tensile strength of 420 MPa. The ultraviolet (UV) resistance of PLA/CGA fibers were enhanced significantly by the introduction of CGA. When the CGA content was not <3 %, the UV transmittance of PLA/CGA fibers was <8 %. Moreover, PLA/CGA fibers exhibited good antioxidant properties. PLA/CGA fibers with 10 % CGA owned the highest antioxidant rate of >90 %. In addition, the 6-fold drawn PLA/CGA fiber with 10 % CGA presented excellent release performance with a 7-day cumulative CGA release rate of 19 %.

Are bioplastics safe? Hazardous effects of polylactic acid (PLA) nanoplastics in Drosophila

The expanded uses of bioplastics require understanding the potential health risks associated with their exposure. To address this issue, Drosophila melanogaster as a versatile terrestrial in vivo model was employed, and polylactic acid nanoplastics (PLA-NPLs), as a proxy for bioplastics, were tested as a material model. Effects were determined in larvae exposed for 4 days to different concentrations (25, 100, and 400 μg/mL) of 463.9 ± 129.4 nm PLA-NPLs. Transmission electron microscopy (TEM) and scanning electron microscope (SEM) approaches permitted the detection of PLA-NPLs in the midgut lumen of Drosophila larvae, interacting with symbiotic bacteria. Enzymatic vacuoles were observed as carriers, collecting PLA-NPLs and enabling the crossing of the peritrophic membrane, finally internalizing into enterocytes. Although no toxic effects were observed in egg-to-adult survival, cell uptake of PLA-NPLs causes cytological disturbances and the formation of large vacuoles. The translocation across the intestinal barrier was demonstrated by their presence in the hemolymph. PLA-NPL exposure triggered intestinal damage, oxidative stress, DNA damage, and inflammation responses, as evaluated via a wide set of marker genes. Collectively, these structural and molecular interferences caused by PLA-NPLs generated high levels of oxidative stress and DNA damage in the hemocytes of Drosophila larvae. The observed effects point out the need for further studies aiming to deepen the health risks of bioplastics before adopting their uses as a safe plastic alternative.

Visible Light-Regulated Ring-Opening Polymerization of Lactones by Employing Indigo as a Photoacid Catalyst

The development of visible light-regulated polymerizations for precision synthesis of polymers has drawn considerable attention in the past years. In this study, an ancient dye, indigo, is successfully identified as a new and efficient photoacid catalyst, which can readily promote the ring-opening polymerization of lactones under visible light irradiation in a well-controlled manner, affording the desired polyester products with predictable molecular weights and narrow dispersity. The enhanced acidity of indigos by excitation is crucial to the H-bonding activation of the lactone monomers. Chain extension and block copolymer synthesis are also demonstrated with this method.

Poly(Propylene Carbonate)-Based Biodegradable and Environment-Friendly Materials for Biomedical Applications

Poly(propylene carbonate) (PPC) is an emerging "carbon fixation" polymer that holds the potential to become a "biomaterial of choice" in healthcare owing to its good biocompatibility, tunable biodegradability and safe degradation products. However, the commercialization and wide application of PPC as a biomedical material are still hindered by its narrow processing temperature range, poor mechanical properties and hydrophobic nature. Over recent decades, several physical, chemical and biological modifications of PPC have been achieved by introducing biocompatible polymers, inorganic ions or small molecules, which can endow PPC with better cytocompatibility and desirable biodegradability, and thus enable various applications. Indeed, a variety of PPC-based degradable materials have been used in medical applications including medical masks, surgical gowns, drug carriers, wound dressings, implants and scaffolds. In this review, the molecular structure, catalysts for synthesis, properties and modifications of PPC are discussed. Recent biomedical applications of PPC-based biomaterials are highlighted and summarized.

Evaluation of bioplastics biodegradation under simulated landfill conditions

Bioplastics that are generated from renewable sources have been regarded as an alternative to conventional plastics. Polylactic acid (PLA) is one of the mostly produced bioplastics because of its long shelf life for various applications. Even though bioplastics have drawn attention recently, their ultimate fate in landfills is still unknown. In this study, a standardized laboratory-scale lysimeter experiment was performed for the simulation of landfill conditions in order to evaluate the biodegradability of PLA during municipal solid waste stabilization. The reactors were loaded with municipal solid waste (MSW) taken from an operating landfill, certified PLA cups, and seed sludge. Various phases of landfill stabilization were simulated; hence, the reactors were operated under aerobic, semi-aerobic, and anaerobic conditions, respectively. Throughout the operation, both leachate and biogas generation in the reactors were regularly monitored. At the end of each phase, bioplastic cups were removed from the reactors, gently cleaned, weighed, and examined under a scanning electron microscope (SEM). The experimental results indicated that bioplastics did not undergo significant biodegradation during the first two stabilization phases (aerobic and semi-aerobic). On the other hand, it was observed that the cups were much softer and whiter at the end of the anaerobic phase. The weight of cups decreased by 12.8% on average, and their surfaces were prominently damaged after the completion of the last phase indicating the potential signs of biodegradation.

Vegetal Polyphenol Extracts as Antioxidants for the Stabilization of PLA: Toward Fully Biobased Polymer Formulation

The use of natural antioxidants as substitutes for traditional synthetic stabilizers has been investigated for the stabilization of biobased and biodegradable polymers, with the aim of designing fully biobased plastic formulations. This study focused on the thermo- and photostabilization of poly(lactic acid) (PLA) using vegetal polyphenol extracts as biosourced antioxidants. The polyphenols were extracted by microwave-assisted extraction from the valorization of vegetal waste, and their potential as antioxidant additives was evaluated (e.g., polyphenol content, composition, and antioxidant activity). PLA was then formulated with 2 wt % of the extracts exhibiting the highest antioxidant activities: green tea residues, pomegranate peels, grape marc, bramble leaves, and yellow onion peel extracts. The efficiency of the natural additives as thermal stabilizers was evaluated and compared with a synthetic antioxidant using rheological and thermal analyses. The results demonstrated the capacity of grape marc extract and pomegranate peel extract to significantly improve PLA thermal stability during processing and thermo-oxidation. Finally, photorheology was conducted to evaluate the influence of the bioadditives on the biopolyester photodegradation. The different polyphenol extracts seemed to significantly hinder the photo-oxidation of PLA and constitute very promising natural UV stabilizers, combining UV absorbers and antioxidant functions.

Biobased Films Based on Chitosan and Microcrystalline Cellulose for Sustainable Packaging Applications

The transition to a more sustainable lifestyle requires a move away from petroleum-based sources and the investigation and funding of renewable and waste feedstocks to provide biobased sustainable materials. The formulation of films based on chitosan and microcrystalline cellulose with potential applications in the packaging sector has been demonstrated. Glycerol is also used as a plasticizer in the formulation of flexible films, while mucic acid is used as a valid alternative to acetic acid in such films. The film based on chitosan, microcrystalline cellulose, glycerol, and mucic acid shows properties and a performance similar to those of the film formulated with acetic acid, and, in addition, it seems that the photo-oxidation resistance of the film based on mucic acid is better than that of the material containing acetic acid. The films were characterized using spectroscopy (FTIR and UV-vis), tensile testing, water contact angle measurements, surface observations, and photo-oxidation resistance measurements. The presence of microcrystalline cellulose enhances the mechanical behavior, UV barrier properties, and surface hydrophobicity of the film. The feasibility of formulating chitosan-based films, with or without microcrystalline cellulose, which exhibit good properties and performances is demonstrated. Mucic acid instead of acetic acid is used in the formulation of these film.

Exclusive D-lactate-isomer production during a reactor-microbiome conversion of lactose-rich waste by controlling pH and temperature

Lactate is among the top-ten-biobased products. It occurs naturally as D- or L-isomer and as a racemic mixture (DL-lactate). Generally, lactate with a high optical purity is more valuable. In searching for suitable renewable feedstocks for lactate production, unutilized organic waste streams are increasingly coming into focus. Here, we investigated acid whey, which is a lactose-rich byproduct of yogurt production, that represents a considerable environmental footprint for the dairy industry. We investigated the steering of the lactate-isomer composition in a continuous and open culture system (HRT = 0.6 d) at different pH values (pH 5.0 vs. pH 6.5) and process temperatures (38°C to 50°C). The process startup was achieved by autoinoculation. At a pH of 5.0 and a temperature of 47°C-50°C, exclusive D-lactate production occurred because of the dominance of Lactobacillus spp. (> 95% of relative abundance). The highest volumetric D-lactate production rate of 722 ± 94.6 mmol C L-1 d-1 (0.90 ± 0.12 g L-1 h-1), yielding 0.93 ± 0.15 mmol C mmol C-1, was achieved at a pH of 5.0 and a temperature of 44°C (n = 18). At a pH of 6.5 and a temperature of 44°C, we found a mixture of DL-lactate (average D-to-L-lactate production rate ratio of 1.69 ± 0.90), which correlated with a high abundance of Streptococcus spp. and Enterococcus spp. However, exclusive L-lactate production could not be achieved. Our results show that for the continuous conversion of lactose-rich dairy waste streams, the pH was a critical process parameter to control the yield of lactate isomers by influencing the composition of the microbiota. In contrast, temperature adjustments allowed the improvement of bioprocess kinetics.

Enhancing the Hydrolytic Stability of Poly(lactic acid) Using Novel Stabilizer Combinations

Commercially available poly(lactic acid) exhibits poor hydrolytic stability, which makes it impossible for use in durable applications. Therefore, a novel hydrolysis inhibitor based on an aziridine derivative as well as a novel stabilizer composition, containing an aziridine derivative and an acid scavenger, were investigated to improve the hydrolytic stability. To evaluate the stabilizing effect, the melt volume rate (MVR) and molecular weight were monitored during an accelerated hydrolytic aging in water at elevated temperatures. Temperatures were selected according to the glass transition temperature (~60 °C) of PLA. It was shown that the novel hydrolysis inhibitor as well as the novel stabilizer composition exhibited excellent performance during hydrolytic aging, exceeding commercially available alternatives, e.g., polymeric carbodiimides. A molecular weight analysis resulted in a molecular weight decrease of only 10% during approximately 850 h and up to 20% after 1200 h of hydrolytic aging, whereas poly(lactic acid) stabilized with a commercial polycarbodiimide revealed comparable molecular weight reductions after only 300 h. Furthermore, the stabilization mechanism of the aziridine derivative alone, as well as in the synergistic combination with the acid scavenger (calcium hydrotalcite), was investigated using nuclear magnetic resonance (NMR) spectroscopy. In addition to an improved hydrolytic stability, the thermal properties were also enhanced compared to polymeric carbodiimides.

Photodegradation of biodegradable plastics in aquatic environments: Current understanding and challenges

Direct and indirect photolysis are important abiotic processes in aquatic environments through which plastics can be transformed physically and chemically. Transport of biodegradable plastics in water is influenced by vertical mixing and turbulent flow, which make biodegradable plastics remain susceptible to sunlight and photolysis despite their high density. In general, biodegradable plastics are composed of ester containing polymers (e.g., poly(butylene succinate), polyhydroxyalkanoate, and polylactic acid), whereas non-biodegradable plastics are composed of long chains of saturated aliphatic hydrocarbons in their backbones (e.g., polyethylene, polypropylene, and polystyrene). Based on the reviewed knowledge and discussion, we may hypothesize that 1) direct photolysis is more pronounced for non-biodegradation than for biodegradable plastics, 2) smaller plastics such as micro/nano-plastics are more prone to photodegradation and photo-transformation by direct and indirect photolysis, 3) the production rate of reactive oxygen species (ROS) on the surface of biodegradable plastics is higher than that of non-biodegradable plastics, 4) the photodegradation of biodegradable plastics may be promoted by ROS produced from biodegradable plastics themselves, and 5) the subsequent reactions of ROS are more active on biodegradable plastics than non-biodegradable plastics. Moreover, micro/nanoplastics derived from biodegradable plastics serve as more effective carriers of organic pollutants than those from non-biodegradable plastics and thus biodegradable plastics may not necessarily be more ecofriendly than non-biodegradable plastics. However, biodegradable plastics have been largely unexplored from the viewpoint of direct or indirect photolysis. Roles of reactive oxygen species originating from biodegradable plastics should be further explored for comprehensively understanding the photodegradation of biodegradable plastics.

Super-tough poly(lactic acid)/silicone rubber thermoplastic vulcanizates: The organic and inorganic synergistic interfacial compatibilization

Polymer modification using silicone rubber represents a promising avenue for enhancing physico-mechanical properties. However, achieving optimal performance through direct blending is hindered by the poor interface compatibility between silicone rubber and the matrix. In this study, we prepared super-tough thermoplastic vulcanizates (TPVs) of polylactic acid/silicone rubber through dynamic vulcanization with PLA, methyl vinyl silicone rubber (MVQ), glycidyl methacrylate grafted MVQ (MVQ-g-GMA), and fumed silica nanoparticles (SiO2). The impact of the SiO2 addition in MVQ on the morphology, mechanical properties, crystallization, and thermal properties of the TPVs was investigated. The results showed that MVQ-g-GMA and SiO2 exhibited a synergistic compatibilization effect significantly improving the interfacial adhesion between PLA and MVQ. Therefore, the impact and tensile strength of the TPVs increased from 8.0 kJ/m2 and 22.2 MPa to 62.6 kJ/m2 and 36.7 MPa, respectively. Moreover, the TPVs also presented good low-temperature toughness with a maximum impact strength of 40.4 kJ/m2 at -20 °C. Additionally, improvements in thermal stability and crystallization rate were also observed. Overall, combining organic and inorganic synergistic compatibilization is a feasible and effective method to fabricate outstanding low-temperature toughness to PLA.

Influence of bio-coupling agent on interfacial interlocking compatibility and toughness of ultrafine bamboo charcoal/polylactic acid composite film

Applications for polylactic acid (PLA) are significantly impacted by its poor mechanical properties and lack of thermal stability. The goal of this work is to bridge the gap of poor compatibility among the components and enhance their interface interlocking capability to improve the toughness and thermal stability. Ultrafine bamboo charcoal (UFBC) was treated through deep eutectic solvent (DES) method to deposit sodium lignosulfonate (LS) on its surface. LS was used with PLA as a bio-coupling agent to create an eco-friendly PLA composite film with a wide range of characteristics. Benefiting from the penetration of PLA to the internal pores in UFBC, the resultant L-UFBC/PLA film has a good mechanical interlocking structure. Ls can increase the compatibility and strengthen the interface interlocking capability through DES method, which greatly improves the mechanical properties of the system. In comparison to pure PLA one, the elongation at break was 136.24 % greater, and the crystallinity (Xc) increased from 1.09 % to 3.33 %. Furthermore, the thermal stability of the system was also improved, and the residual at 600 °C rose by 4.83 %. These characteristics offer the prepared L-UFBC/PLA film a wide range of potential applications in the packaging, medical, agricultural, and other sectors.

Observation of Ferroelectric Lithography on Biodegradable PLA Films

Ferroelectric lithography, which can purposefully control and pattern ferroelectric domains in the micro-/nanometer scale, has extensive applications in data memories, field-effect transistors, race-track memory, tunneling barriers, and integrated biochemical sensors. In pursuit of mechanical flexibility and light weight, organic ferroelectric polymers such as poly(vinylidene fluoride) are developed; however, they still suffer from complicated stretching processes of film fabrication and poor degradability. These poor features severely hinder their applications. Here, the ferroelectric lithography on the biocompatible and biodegradable poly(lactic acid) (PLA) thin films at room temperature is demonstrated. The semicrystalline PLA thin film can be easily fabricated through the melt-casting method, and the desired domain structures can be precisely written according to the predefined patterns. Most importantly, the coercive voltage (Vc ) of PLA thin film is relatively low (lower than 30 V) and can be further reduced with the decrease of the film thickness. These intriguing behaviors combined with satisfying biodegradability make PLA thin film a desirable candidate for ferroelectric lithography and enable its future application in the field of bioelectronics and biomedicine. This work sheds light on further exploration of ferroelectric lithography on other polymer ferroelectrics as well as their application as nanostructured devices.

Exploitation of microbial activities at low pH to enhance planetary health

Awareness is growing that human health cannot be considered in isolation but is inextricably woven with the health of the environment in which we live. It is, however, under-recognized that the sustainability of human activities strongly relies on preserving the equilibrium of the microbial communities living in/on/around us. Microbial metabolic activities are instrumental for production, functionalization, processing, and preservation of food. For circular economy, microbial metabolism would be exploited to produce building blocks for the chemical industry, to achieve effective crop protection, agri-food waste revalorization, or biofuel production, as well as in bioremediation and bioaugmentation of contaminated areas. Low pH is undoubtedly a key physical-chemical parameter that needs to be considered for exploiting the powerful microbial metabolic arsenal. Deviation from optimal pH conditions has profound effects on shaping the microbial communities responsible for carrying out essential processes. Furthermore, novel strategies to combat contaminations and infections by pathogens rely on microbial-derived acidic molecules that suppress/inhibit their growth. Herein, we present the state-of-the-art of the knowledge on the impact of acidic pH in many applied areas and how this knowledge can guide us to use the immense arsenal of microbial metabolic activities for their more impactful exploitation in a Planetary Health perspective.

Integrated microbiota and multi-omics analysis reveal the differential responses of earthworm to conventional and biodegradable microplastics in soil under biogas slurry irrigation

As one of the promising alternatives of conventional plastic mulching film (C-PMF), biodegradable plastic mulching films (B-PMF) were employed in agronomy production to alleviate the environmental burden of C-PMF. However, information regarding the potential toxicity effects of biodegradable microplastics (MPs) in soil still in scarcity, and the available findings were found to be controversial. Additionally, little is known about the molecular toxicity effects of conventional and biodegradable MPs on terrestrial organisms. Thus, 5 % (w/w) biodegradable (polylactic acid, PLA) and conventional (polyvinylchloride, PVC; low-density polyvinylchloride, LDPE) MPs were employed to assess the toxicity effects on Eisenia fetida in agricultural soil with biogas slurry irrigation. In the present study, transcriptomic, metabolomic profiles and individual indexes were selected to reveal the toxicity mechanisms from molecular level to the individual response. Furthermore, dysbiosis of bacterial community in gut was also investigated for obtaining comprehensive knowledge on the MPs toxicity. At the end of the exposure, the number of survival earthworms after MPs exposure was significantly reduced. Compared with the initial body weight, PLA and LDPE increased the biomass of earthworms after MPs exposure, while no significant influence on the biomass was observed in PVC treatment. Microbacterium, Klebsiella and Chryseobacterium were significantly enriched in earthworm gut after PLA, PVC and LDPE exposure, respectively (p < 0.05). Transcriptomic and metabolomic analysis revealed that PLA exposure induced neurotransmission disorder and high energetic expenditure in earthworms. However, PVC and LDPE inhibited the nutrient absorption efficiency and activated the innate immunity responses of earthworms. The PLS-SEM results showed that the effects of MPs were dominated by the polymer types, and hence, significantly and directly influence the gut bacterial community of earthworms. This study provides a better understanding of the similarities and discrepancies in toxicity effects of biodegradable and conventional MPs from the perspectives of individual, gut bacterial community, transcriptome and metabolome.

Selective Transesterification to Control Copolymer Microstructure in the Ring-Opening Copolymerization of Lactide and ε-Caprolactone by Lanthanum Complexes

A series of novel lanthanum amido complexes, supported by ligands designed around the salan framework (salan = N,N'-bis(o-hydroxy, m-di-tert-butylbenzyl)-1,2-diaminoethane) were synthesized and fully characterized in the solid and solution states. The ligands incorporate benzyl or 2-pyridyl substituents at each tertiary amine center. The complexes were investigated as catalysts in the ring-opening homopolymerization of lactide (LA) and ε-caprolactone (ε-CL) and copolymerization of equimolar amounts of LA and ε-CL at ambient temperature. Solvent (THF or toluene) and the number of 2-pyridyl groups in the complex were found to influence the reactivity of the catalysts in copolymerization reactions. In all cases, complete conversion of LA to PLA was observed. The use of THF, a coordinating solvent, suppressed ε-CL polymerization, while the presence of one or more 2-pyridyl groups promoted ε-CL polymerization. Each copolymer gave a monomodal trace in gel permeation chromatography-size-exclusion chromatography (GPC-SEC) experiments, indicative of copolymer formation over homopolymerization. Copolymer microstructure was found to be dependent on catalyst structure and reaction solvent, ranging from blocky to close to alternating. Experiments revealed rapid conversion of LA in the initial stages of the reaction, followed by incorporation of ε-CL into the copolymer by either transesterification or propagation reactions. Significantly, the mode of transesterification (TI or TII) that occurs is determined by the structure of the metal complex and the reaction solvent, leading to the possibility of controlling copolymer microstructure through catalyst design.