Examination of microbial fuel cell start-up times with domestic wastewater and additional amendments

Optimizing electrochemically active microorganisms as a key player in the bioelectrochemical system: Identification methods and pathways to large-scale implementation

The rapid global economic growth driven by industrialization and population expansion has resulted in significant issues, including reliance on fossil fuels, energy scarcity, water crises, and environmental emissions. To address these issues, bioelectrochemical systems (BES) have emerged as a dual-purpose solution, harnessing electrochemical processes and the capabilities of electrochemically active microorganisms (EAM) to simultaneously recover energy and treat wastewater. This review examines critical performance factors in BES, including inoculum selection, pretreatment methods, electrodes, and operational conditions. Further, authors explore innovative approaches to suppress methanogens and simultaneously enhance the EAM in mixed cultures. Additionally, advanced techniques for detecting EAM are discussed. The rapid detection of EAM facilitates the selection of suitable inoculum sources and optimization of enrichment strategies in BESs. This optimization is essential for facilitating the successful scaling up of BES applications, contributing substantially to the realization of clean energy and sustainable wastewater treatment. This analysis introduces a novel viewpoint by amalgamating contemporary research on the selective enrichment of EAM in mixed cultures. It encompasses identification and detection techniques, along with methodologies tailored for the selective enrichment of EAM, geared explicitly toward upscaling applications in BES.

Examining the resistance and resilience of anode-respiring Shewanella oneidensis biohybrid using microsensors

Immobilizing electro-active microbes within polymer matrices (thereby forming biohybrids) is a promising approach to accelerate microbial attachment to electrodes and increase the biofilm robustness. However, little is known on the fine scale chemical environment that develops within the electro-active biohybrids. Herein, we develop a biohybrid by immobilizing a culture of Shewanella oneidensis MR1 in agar matrix on the surface of a graphite electrode poised at +0.25 V. The resulting bioanode (3-6 mm thick) was grown under anoxic conditions and produced a steady current of 40 μA. Oxygen and pH distribution within the biohybrid were characterized in-situ using microsensors. As Shewanella is a facultative aerobe, it will halt the current production in the presence of oxygen. Thus, in addition, we investigated the alteration of the microenvironment during and after aeration of the medium to evaluate the oxygen tolerance of the system. During aeration, oxygen was effectively consumed in the top layers of the biofilm, leaving a 400-900 μm thick anoxic zone on the anode surface, that sustained >60% of the initial current. Current production recovered to pre-oxic condition within 5 h after the aeration was stopped, showing that immobilization can promote both high resistance and resilience of the system. Despite the absence of strong buffering conditions, pH profiles indicated a maximum drop of 0.2 units across the biohybrid. Characterizing the chemical microenvironment helps to elucidate the mechanistic functioning of artificial biofilms and hold a great potential for the designing of future, more effective biohybrid electrodes.

Instant water toxicity detection based on magnetically-constructed electrochemically active biofilm

Water toxicity determination with electrochemically active bacteria (EAB) is promising in the early warning of water pollution. However, limited by tedious biofilm formation, natural EAB biofilms are uncapable of the instant detection of water toxicity, resulting in the failure for the emergency monitoring of water pollution. To solve this problem, a novel method for the rapid construction of EAB biofilms using magnetic adsorption was established, and the performance of instant water toxicity detection with magnetically-constructed EAB biofilm was investigated. The results demonstrate that EAB biofilms were magnetically constructed in less than 30 min, and magnetically-constructed EAB biofilm generated stable currents even under continuous flow conditions. Magnetically-constructed EAB biofilms realized instant water toxicity detection, and the sensitivity increased with the decrease of magnetic field intensity. Low magnetic field intensity resulted in a loose biofilm structure, which is conducive to toxic pollutant penetration. The detection limit for Cu2+, phenol, and Cd2+ achieved 0.07 mg/L with optimal magnetic field intensity, and the detection time was less than 30 min. This study broadens the application of water toxicity determination with EAB, and establishes a foundation for the instant and continuous detection of water toxicity with EAB.

Biotechnology to reduce logistics burden and promote environmental stewardship for Air Force civil engineering requirements

This review provides discussion of advances in biotechnology with specific application to civil engineering requirements for airfield and airbase operations. The broad objectives are soil stabilization, waste management, and environmental protection. The biotechnology focal areas address (1) treatment of soil and sand by biomineralization and biopolymer addition, (2) reduction of solid organic waste by anaerobic digestion, (3) application of microbes and higher plants for biological processing of contaminated wastewater, and (4) use of indigenous materials for airbase construction and repair. The consideration of these methods in military operating scenarios, including austere environments, involves comparison with conventional techniques. All four focal areas potentially reduce logistics burden, increase environmental sustainability, and may provide energy source, or energy-neutral practices that benefit military operations.

A three-dimensional phenolic-based carbon anode for microbial electrochemical system with customized macroscopic pore structure to promote interior bacteria colonization

Microbial electrochemical system (MES) is an emerging wastewater treatment technology that compensates the energy demands of containments removal by in situ converting the chemical energy of organic pollutants. As the structure for exoelectrogens and the reaction site of extracellular electron transfer (EET), the anode is essential for MES. The future commercial application of MES requires efficiency and large-scale fabrication available anode. In this study, a 3D anode with millimeter-scale pores (3D-MPA) was successfully constructed by sacrificial template method, with low-cost phenolic resin as carbon precursor and polymethyl methacrylate (PMMA) pellets as template. With customized and ordered pore of 1 mm, the 3D-MPAs allowed the microorganisms to colonize inside, improving anodic space utilization efficiency. Different carbonization temperature in tested range from 700 °C to 1000 °C regulated the micrometer-scale convex structures and surface roughness of 3D-MPAs, causing electrochemical performance changes. The 3D-MPA-900 obtained the largest electroactive surface area (102 ± 4.1 cm²) and smallest ohmic resistance (1.8 ± 0.09 Ω). Equipped with MES, 3D-MPA-900 reached the highest power density and current density (2590 ± 25 mW m^-2 and 5.20 ± 0.07 A m^-2). Among tested 3D-MPA, the excellent performance of 3D-MPA-900 might be attributed by its convex structures with suitable size and surface coverage. The surface roughness of 3D-MPA-900 enhanced the microorganism adherence, which then promoted EET on anode surface. Generally, phenolic-based 3D-MPA made of sacrificial-template method had controllable porous structure, large-scale fabrication availability, high chemical stability and excellent mechanical property, which could be promising for the commercial application of MES.

A novel real-time TMAO detection method based on microbial electrochemical technology

Trimethylamine N-oxide (TMAO) is considered to be a novel biomarker of cardiovascular diseases. However, the traditional TMAO detection method has failed to meet the requirements of real-time and point-of-care tests. Herein, a novel TMAO detection method based on microbial electrochemical technology is established, which realizes the direct conversion of TMAO concentration into electrical signals. Attached Shewanella loihica PV-4 was first proven to be capable of simultaneous inward extracellular electron transfer and TMAO reduction. The TMAO detection method showed a wide linear range of 0 to 250 μM, a high sensitivity of 23.92 μA/mM, and a low limit of detection of 5.96 μM. In addition, the TMAO detection process was accomplished within 600 s, with an acceptable accuracy of 90% in the real serum, showing high feasibility in clinical applications.

Degradation of diclofenac via sequential reduction-oxidation by Ru/Fe modified biocathode dual-chamber bioelectrochemical system: Performance, pathways and degradation mechanisms

A sequential reduction-oxidation for DCF degradation was proposed by alternating anaerobic/aerobic conditions at Ru/Fe-biocathode in a dual-chamber bioelectrochemical system (BES). Results showed that Ru/Fe-electrode was successfully fabricated by in-situ electro-deposition, which was rough and uniformly distributed with Ru⁰ and Fe⁰ particles. The morphologic changing and biocompatibility were favorable to increase the surface area and enhance microbial adhesion on Ru/Fe-electrode. At an applied voltage of 0.6 V, the potential and impedance of Ru/Fe-biocathode were -0.80 V and 26 Ω, respectively, lower than that of carbon-felt-biocathode. It led to a higher DCF degradation efficiency of 93.2% under anaerobic conditions, which was superior to that of 88.0% under aerobic conditions. Using NaHCO₃ as carbon source, DCF removal efficiency increased with increasing applied voltage, but decreased with increasing initial DCF concentration. Thirteen intermediates were measured, and two degradation pathways were proposed, among which sequential reduction-oxidation of DCF was the main pathway, dechlorination intermediates were first generated by [H] attacked under anaerobic conditions, further oxidized by microbes and OH attacked under aerobic conditions, achieving 69.6% of mineralization. After 4 d of reaction, microcystis aeruginosa growth inhibition rate decreased from 22.9 to 8.0%, signifying a significant reduction in biotoxicity. Bacteria (e.g. Nitrobacter, Nitrosomonas, Pseudofulvimonas, Aquamicrobium, Sulfurvermis, Lentimicrobiaceae, Anaerobineaceae, Bacteroidales, Hydrogenedensaceae, Dethiosulfatibacter and Azoarcus) for DCF degradation were enriched in Ru/Fe-biocathode. Microbes in Ru/Fe-biocathode had established defense mechanisms to acclimate to the unfriendly environment, while Ru/Fe-biocathode possessed higher nitrification and denitrification activities than carbon-felt-biocathode, and Ru/Fe-biocathode might be of aerobic and anaerobic biodegradation activities. DCF could be mineralized by the synergistic reaction between Ru/Fe and bacteria under sequential anaerobic/aerobic conditions.

Bio-energy generation and treatment of tannery effluent using microbial fuel cell

In this study, Graphite Particle (GP) and Carbon Cloth (CC) are employed as anode electrodes to study both bio-energy generation, and decrease of Chemical Oxygen Demand (COD) simultaneously using tannery effluent. The influence of electrodes distance (10 cm and 20 cm) on electricity production was evaluated. COD removal level of GP (75%) and CC (60%), maximum power outputs for 10 cm distance (600 ± 5 mW m^-2) & (500 ± 10 mW m^-2) and for 20 cm distance (520 ± 5 mW m^-2) and also (430 ± 20 mW m^-2) GP and CC were noted correspondingly. The outcomes of different parameters of MFC namely pH, conductivity, COD concentration, membrane thickness and size of bio-energy generation from tannery effluent in the MFC were investigated. The experimental results reveal that electrode provides highest power output with 10 cm distance between anode and cathode chamber. As a result, GP electrode is gradually viable, biocompatible, effective and adaptable for field application in MFC. The GP electrode has high potential for more power output, when compared to the CC electrode. The MFC system performance was improved with increasing effluent COD concentration (2340-4720 ppm), anolyte conductivity (1.6-8.1 mS cm^-1) and membrane area (9-20 cm²). The system working with conductivity of 8.1 mS cm^-1 and its effluent COD concentration of 4720 ppm generated the maximum peak power density of 44.69 mW m^-2 with respective current density of 109 mA m^-2. The findings thus show that considerable power production and effluent treatment can be achieved by MFC.

Single-Chamber Microbial Fuel Cell with Multiple Plates of Bamboo Charcoal Anode: Performance Evaluation

In this study, three single-chamber microbial fuel cells (MFCs), each having Pt-coated carbon cloth as a cathode and four bamboo charcoal (BC) plates as an anode, were run in a fed-batch mode, individually and in series. Simulated potato-processing wastewater was used as a substrate for supporting the growth of a mixed bacterial culture. The maximum power output increased from 0.386 mW with one MFC to 1.047 mW with three MFCs connected in series. The maximum power density, however, decreased from 576 mW/m2 (normalized to the cathode area) with one MFC to 520 mW/m2 with three MFCs in series. The experimental results showed that power can be increased by connecting the MFCs in series; however, choosing low resistance BC is crucial for increasing power density.

Efficiency and microbial diversity of aeration solid-phase denitrification process bioaugmented with HN-AD bacteria for the treatment of low C/N wastewater

To evaluate the simultaneous nitrification and denitrification (SND) performance of the aeration solid-phase denitrification (SPD) process and improve the operating efficiency, aeration SPD process using polybutanediol succinate as carbon source was optimized and the process was bioaugmented with heterotrophic nitrification-aerobic denitrification bacteria for the treatment of real wastewater. The results showed that after bioaugmentation, the total nitrogen removal efficiency of the aeration SPD process increased by 50.46 % under condition of dissolved oxygen (DO) 3 mg/L. According to Illumina MiSeq sequencing and correlation analyses, the microbial community can perform SND under the conditions of DO 5 mg and HRT 6 h, but is susceptible to DO. Bioaugmentation mainly affected the carbon source metabolic network with heterotrophic bacteria Methyloversatilis, Thiothrix, and norank_Lentimicrobiaceae as nodes to change the community structure, thereby improving the performance of the functional microbial community. Kyoto Encyclopedia of Genes and Genomes analysis suggested that narB, narG, narH, nirK and narI were the key genes involved in the response to bioaugmentation. This work provides new insights for the application of the SPD process in wastewater treatment.

A review of the operating parameters on the microbial fuel cell for wastewater treatment and electricity generation

Environmental and economic considerations suggest a more efficient and comprehensive use of biomass for bioenergy production. One of the most attractive technologies is the microbial fuel cell using the catabolic activity of microorganisms to generate electricity from organic matter. The microbial fuel cell (MFC) has operational benefits and higher performance than current technologies for producing energy from organic materials because it converts electricity from the substrate directly (at ambient temperature). However, MFCs are still not suitable for high energy demand due to practical limitations. The overall performance of an MFC depends on the electrode material, the reactor design, the operating parameters, substrates, and microorganisms. Furthermore, the optimization of the parameters will lead to the commercial development of this technology in the near future. The simultaneous effect of the parameters on each other (intensifier or attenuator) has also been investigated. The investigated parameters in this study include temperature, pH, flow rate and hydraulic retention time, mode, external resistance, and initial concentration.

Microbial electrolysis cells for return flow: Simultaneous nitrogen and carbon removal

The concentration of solids in secondary sludge before anaerobic digestion in a wastewater treatment plant, bring about the production of a return flow, which contains high concentrations of all the common pollutant parameters. This return flow could unfavourably affect the performance of the processes and effluent quality of the waterline. Here, we report the utilisation of three similar microbial electrolysis cells reactors that performs simultaneous carbon and nitrogen removal to reduce the impact of the return flow in the plant. The result of the batch-fed (72 h) experiment showed COD and total nitrogen removal efficiencies that reached 90% and 80%, respectively, supporting the premise that return flows are suitable substrates for a bioelectrochemical treatment. The three reactors followed similar trends, showing good replicability and confirming the potential of MECs as a feasible technology for return flow treatment. Furthermore, when cathodic conversion efficiency was higher than 80%, the pure hydrogen production allows to recover the electric energy consumption, indicating that the system could be theoretically energy neutral.

Artificial electrochemically active biofilm for improved sensing performance and quickly devising of water quality early warning biosensors

A major challenge for devising an electrochemically active biofilm (EAB)-based biosensor for real-time water quality early-warning is the formation of EAB that requires several days to weeks. Besides the onerous and time-consuming preparation process, the naturally formed EABs are intensively concerned as they can hardly deliver repeatable electrical signals even at identical experimental conditions. To address these concerns, this study employed sodium alginate as immobilization agent to encapsulate Shewanella oneidensis MR-1 and prepared EAB for devising a biosensor in a short period of less than 1 h. The artificial EAB were found capable of delivering highly consistent electrical signals with each other when fed with the same samples. Morphology and bioelectrochemical properties of the artificial EAB were investigated to provide interpretations for these findings. Different concentrations of bacteria and alginate in forming the EAB were investigated for their effects on the biosensor's sensitivity. Results suggested that lower concentration of bacteria would be beneficial until it increased to 0.06 (OD₆₆₀). Concentration of sodium alginate affected the sensitivity as well and 1% was found an optimum amount to serve in the formation of EAB. A long-term operation of the biosensor with artificial EAB for 110 h was performed. Clear warning signals for incoming toxicants were observed over random signal fluctuations. All results suggested that the artificial EAB electrode would support a rapid devised and highly sensitivity biosensor.

Substrate salinity: A critical factor regulating the performance of microbial fuel cells, a review

Substrate salinity is a critical factor influencing microbial fuel cells (MFCs) performance and various studies have suggested that increasing substrate salinity first improves MFC performance. However, a further increase in salinity that exceeds the salinity tolerance of exoelectrogens shows negative effects because of inhibited bacterial activity and increased activation losses. In this review, electricity generation and contaminant removal from saline substrates using MFCs are summarized, and results show different optimal salinities for obtaining maximum performance. Then, electroactive bacteria capable of tolerating saline environments and strategies for improving salinity tolerance are discussed. In addition to ohmic resistance and bacterial activity, membrane resistance and catalyst performance will also be affected by substrate salinity, all of which jointly contribute the final overall MFC performance. Therefore, the combined effect of salinity is analyzed to illustrate how the MFC performance changes with increasing salinity. Finally, the challenges and perspectives of MFCs operated in saline environments are discussed.

Anode Surface Bioaugmentation Enhances Deterministic Biofilm Assembly in Microbial Fuel Cells

Microbial fuel cells (MFCs) generate energy while aiding the biodegradation of waste through the activity of an electroactive mixed biofilm. Metabolic cooperation is essential for MFCs' efficiency, especially during early colonization. Thus, examining specific ecological processes that drive the assembly of anode biofilms is highly important for shortening startup times and improving MFC performance, making this technology cost-effective and sustainable. Here, we use metagenomics to show that bioaugmentation of the anode surface with a taxonomically defined electroactive consortium, dominated by Desulfuromonas, resulted in an extremely rapid current density generation. Conversely, the untreated anode surface resulted in a highly stochastic and slower biofilm assembly. Remarkably, an efficient anode colonization process was obtained only if wastewater was added, leading to a nearly complete replacement of the bioaugmented community by Geobacter lovleyi Although different approaches to improve MFC startup have been investigated, we propose that only the combination of anode bioaugmentation with wastewater inoculation can reduce stochasticity. Such an approach provides the conditions that support the growth of specific newly arriving species that positively support the fast establishment of a highly functional anode biofilm.IMPORTANCE Mixed microbial communities play important roles in treating wastewater, in producing renewable energy, and in the bioremediation of pollutants in contaminated environments. While these processes are well known, especially the community structure and biodiversity, how to efficiently and robustly manage microbial community assembly remains unknown. Moreover, it has been shown that a high degree of temporal variation in microbial community composition and structure often occurs even under identical environmental conditions. This heterogeneity is directly related to stochastic processes involved in microbial community organization, similarly during the initial stages of biofilm formation on surfaces. In this study, we show that anode surface pretreatment alone is not sufficient for a substantial improvement in startup times in microbial fuel cells (MFCs), as previously thought. Rather, we have discovered that the combination of applying a well-known consortium directly on the anode surface together with wastewater (including the bacteria that they contain) is the optimized management scheme. This allowed a selected colonization process by the wastewater species, which improved the functionality relative to that of untreated systems.

Ferric iron stimulation in marine SMFCs: Impact on the microbial structure evolution in contaminated sediments with low and high molecular weight PAHs

The impact of ferric iron stimulation on the evolution of microbial structure in marine sediment microbial fuel cells (SMFCs), operated for the bioremediation of a complex mixture of low and high molecular weight PAHs (naphthalene, fluorene, pyrene and benzo(a)pyrene), was assessed. Microbial evolution profiles showed high relative abundances of exoelectrogenic iron-reducing bacteria throughout the biodegradation, namely Geoalkalibacter, under ferric iron stimulation and anode reducing conditions, irrespective of sulfate reducing bacteria (SRB) inhibition. Highest PAHs removal was measured in the absence of anode reduction, under Fe stimulation and SRB inhibition, reaching 40.85% for benzo(a)pyrene, the most persistent PAH used in this study. Results suggest that amendment of contaminated sediment with ferric iron could constitute a better bioremediation strategy than using SMFCs. This becomes significant when considering the well-established and dominant indigenous SRB population in marine sediments that usually limits the performance of the anode as a terminal electron acceptor in marine SMFCs.

Hibernations of electroactive bacteria provide insights into the flexible and robust BOD detection using microbial fuel cell-based biosensors

Microbial fuel cell (MFC) biosensors have been suggested as an alternative detection method for biochemical oxygen demand (BOD). However, it is absolutely essential to develop maintenance procedures for MFC biosensors` because in practice the lay-up period cannot be avoided. In this work, setting electroactive bacteria (EAB) under hibernation condition was demonstrated to be a feasible maintenance method, which provided important insights into the flexible and robust BOD detection using MFC biosensors. Standard BOD solution containing 500, 200, and 20 mg/L BOD were used to evaluate the detection performance after EAB hibernations. Results demonstrated quick recovery of voltage output and high-accuracy BOD detection after hibernations up to 30 days in MFC biosensors detecting 500 mg/L and 200 mg/L BOD. Identical anode potentials after the EAB hibernations suggested intact bacterial ability of current generation. Non-turnover cyclic voltammetry immediately collected after the hibernations suggested multiple redox couples and the presence of cytochromes that played key roles in EAB metabolism and functioned as temporary electron sinks during the hibernations, leading to the increased detected BOD concentration in the restarting cycles. Generally, setting EAB under hibernation condition is a simple and convenient maintenance method for MFC-based BOD biosensors, which not only provides insights into flexible and robust BOD detection, but also be helpful for other MFC biosensing instruments.

The effect of additional salinity on performance of a phosphate buffer saline buffered three-electrode bioelectrochemical system inoculated with wastewater

In bioelectrochemical system (BES), phosphate buffer saline (PBS) is usually used to achieve a suitable pH condition, which also increases electrolyte salinity. A series of factors that change with salinity will affect BES performance. To simplify the scenario, a three-electrode BES is used to investigate how additional salinity affects the performance of a 50 mM PBS-buffered BES. Results demonstrated that current production decreased with increasing salinity and the dominant exoelectrogens were not inhibited with the addition of 200 mM NaCl. The distribution of system resistance was analyzed by electrochemical impedance spectroscopy. Compared to the decreased solution and biofilm resistance, the increased interfacial resistance that accounted for up to 97.8% of total resistance was the dominant reason for the decreased current production with the increasing additional salinity. The effects of additional salinity on acetate degradation and columbic efficiency were also analyzed.

In Vivo Polymerization ("Hard-Wiring") of Bioanodes Enables Rapid Start-Up and Order-of-Magnitude Higher Power Density in a Microbial Battery

For microbial electrochemical technologies to be successful in the decentralized treatment of wastewater, steady-state power density must be improved and cost must be decreased. Here, we demonstrate in vivo polymerization ("hard-wiring") of a microbial community to a growing layer of conductive polypyrrole on a sponge bioanode of a microbial battery, showing rapid biocatalytic current development (∼10 times higher than a sponge control after 4 h). Moreover, bioanodes with the polymerized inoculant maintain higher steady-state power density (∼2 times greater than the control after 28 days). We then evaluate the same hard-wired bioanodes in both a two-chamber microbial fuel cell and microbial battery with a solid-state NaFe^IIFe^III(CN)₆ (Prussian Blue) cathode, showing approximately an order-of-magnitude greater volumetric power density with the microbial battery. The result is a rapid start-up, low-cost (no membrane or platinum catalyst), and high volumetric power density system (independent of atmospheric oxygen) for harvesting energy and carbon from dilute organics in wastewater.

Response of sediment microbial communities to crude oil contamination in marine sediment microbial fuel cells under ferric iron stimulation

In this study, response of the microbial communities associated with the bioremediation of crude oil contaminated marine sediments was addressed using sediment microbial fuel cells (SMFCs). Crude oil was spiked into marine sediments at 1 g/kg of dry sediment to simulate a heavily contaminated marine environment. Conventional SMFCs were used with carbon fiber brushes as the electrode components and were enhanced with ferric iron to stimulate electrochemically active bacteria. Controls were operated under open circuit with and without ferric iron stimulation, with the latter condition simulating natural attenuation. Crude oil removal in the Fe enhanced SMFCs reached 22.0 ± 5.5% and was comparable to the measured removal in the control treatments (19.2 ± 7.4% in natural attenuation SMFCs and 15.2 ± 2.7% in Fe stimulated open circuit SMFCs), indicating no major enhancement to biodegradation under the applied experimental conditions. The low removal efficiency could be due to limitations in the mass transfer of the electron donor to the microbes and the anodes. The microbial community structure showed similarity between the iron stimulated SMFCs operated under the open and closed circuit. Natural attenuation SMFCs showed a unique profile. All SMFCs showed high relative abundances of hydrocarbon degrading bacteria rather than anode reducers, such as Marinobacter and Arthrobacter in the case of the natural attenuation SMFCs, and Gordonia in the case of iron stimulated SMFCs. This indicated that the microbial structure during the bioremediation process was mainly determined by the presence of petroleum contamination and to a lesser extent the presence of the ferric iron, with no major involvement of the anode as a terminal electron acceptor. Under the adopted experimental conditions, the absence of electrochemically active microbes throughout the biodegradation process indicates that the use of SMFCs in crude oil bioremediation is not a successful approach. Further studies are required to optimize SMFCs systems for this aim.

Molecular density regulating electron transfer efficiency of S. oneidensis MR-1 mediated roxarsone biotransformation

Efficient extracellular electron transport is a key for sufficient bioremediation of organoarsenic pollutants such as 4-hydroxy-3-nitrobenzenearsonic acid (roxarsone). The related apparent kinetics characteristics are essential for engineering practice of bioremediation activities and for full understanding the environmental fate of roxarsone, yet remains poorly understood. We report, to our knowledge, the first study of the electron transfer characteristics between roxarsone and participating S. oneidensis MR-1. The electron transfer rate during roxarsone biotransformation was estimated up to 3.1 × 10⁶ electrons/cell/s, with its value being clearly associated with the apparent roxarsone concentration. Lowing roxarsone concentration extended the average separation distance between cells and neighboring roxarsone molecules and thereby augmented electric resistance as well as extended cell movement for foraging, thus reduced electron transfer rate. In addition, the presence of roxarsone significantly stimulated population growth of S. oneidensis MR-1 with nearly doubled maximum specific growth rate, albeit with clearly increased lag time, as compared with that of none-roxarsone scenario. These findings provide, at the first time, basic biostoichiometry of S. oneidensis MR-1 induced roxarsone biotransformation, which may shed lights for full understanding of roxarsone transformation process in waste treatment systems that are necessary for engineering practice and/or environmental risks assessment.

Energy capture from thermolytic solutions and simulated sunlight coupled with hydrogen peroxide production and wastewater remediation

A novel solar salinity energy nexus was developed by combining a photocatalytic fuel cell (PFC) and a reverse electrodialysis (RED). The hybrid cell (called a PRC) can effectively transfer the solar energy and salinity gradient energy (which is regenerated by low grade industrial waste heat) to electrical energy coupled with enhanced pollutant (Rhodamine B, RhB) degradation and H₂O₂ production. Energy-Environment win-win will be realized. The open circuit voltage of the PRC was the sum of those of the PFC and the RED, and the RED stack made the larger contribution to the electricity production of PRC. The bias voltage generated from the RED stack accelerated the separation of photo-induced holes and electrons on the three-dimensional TiO₂ array photoanode, which enhanced RhB degradation and H₂O₂ production. The flow rate and concentration of the working fluids (ammonium bicarbonate) and the reaction conditions in the electrode chambers had substantial effects on the PRC performance. Under the optimal condition, the peak power density and energy efficiency of PRC reached 1500 mW m^-2 and 4.21% respectively. The performance of PRC on electricity production is better than photocatalytic electrolytic cell driven by desalination(PFCD), but not good as microbial reverse electrodialysis electrolysis cell (MREC).

Performance and inorganic fouling of a submergible 255 L prototype microbial fuel cell module during continuous long-term operation with real municipal wastewater under practical conditions

A submergible 255 L prototype MFC module was operated under practical conditions with municipal wastewater having a large share in industrial discharges for 98 days to investigate the performance of two of the largest, ever investigated multi-panel stainless steel/activated carbon air cathodes (85 × 85 cm). At a flow rate of 144 L/d, power density of 78 mW/m²_Cat (317 mW/m³) and COD, TSS and TN removal of 41 ± 16 %, 36 ± 16 % and 18 ± 14 %, respectively, were reached. Observed Coulombic efficiency and substrate-specific energy recovery were 29.5 ± 14 % and 0.184 ± 0.125 kWh_el/kg_COD,deg, respectively. High salt content of wastewater (TDS = 2.8 g/L) led to severe inorganic fouling causing a drastic decline in power output and energy recovery of more than 90 % in the course of experiments. Mechanical cleaning of the cathodes restored only 22 % (17 mW/m²_Cat) of the power output and did not improve nutrient removal or energy recovery.

In situ synthesis of polypyrrole on graphite felt as bio-anode to enhance the start-up performance of microbial fuel cells

This study introduces an effective method to deposit polypyrrole (PPy) on graphite felt (GF) as anode to improve the start-up performance of microbial fuel cells (MFCs). The results of scanning electron microscope (SEM) and electrochemical testing reveal that polypyrrole is able to improve the electrical conductivity and surface roughness, which is beneficial to the microorganism attachment and growth. It shows that microorganisms grow faster on polypyrrole-modified anode than on unmodified anode. It takes ca. 5 days for polypyrrole-modified anode to reach a reproducible voltage platform, while it takes 11 days for unmodified anode. Moreover, the maximum power density of microbial fuel cells with polypyrrole-modified anode was 919 mW m^-2, which were 2.3 times of that with unmodified anode. This research revealed that polypyrrole modification can improve the start-up performance of microbial fuel cells. It is considered as a feasible, economical and sustainable anode.

Development of microbial community within the cathodic biofilm of single-chamber air-cathode microbial fuel cell

The aim of this study was to investigate the development of microbial community within the cathodic biofilm of single-chamber air-cathode microbial fuel cell (MFC). To analyze microbial community structures within cathodic biofilm, cathodic biofilm samples were stratified into three layers, i.e., the cathode-side layer (0-40 μm), the middle layer (40-80 μm), and the anolyte-side layer (80-120 μm). After four starting cycles (0-188 h), the maximum power densities of the MFC fed with 1 g/L acetate decreased from 1056 ± 110 to 410 ± 50 mW/m² within 15 cycles (~30 d) of operation. The relative abundance of Pseudomonas gradually increased from 18.9% in the 1st cycle to 50.2% in the 4th cycle. After 15 cycles, the relative abundance of Pseudomonas became 53.8%, 16.4%, and 8.90% in the middle, anolyte-side, and cathode-side layers, respectively. The aerobic bacteria within the cathodic biofilm increased from 24% in the anodyte-side layer to 43% in the cathode-side layer. The relative abundance of Methanobrevibacter was 42.1% and 37.2% after 3 and 15 cycles, respectively. The bacterial community structures were similar among cycles 2, 3, and 4, but significantly different in the 15th cycle. The results from this study should be useful to understand the mechanism of the cathodic biofilm formation and to develop strategies to enhance performance of the MFC.

Storing of exoelectrogenic anolyte for efficient microbial fuel cell recovery

Starting up a microbial fuel cell (MFC) requires often a long-term culture enrichment period, which is a challenge after process upsets. The purpose of this study was to develop low-cost storage for MFC enrichment culture to enable prompt process recovery after upsets. Anolyte of an operating xylose-fed MFC was stored at different temperatures and for different time periods. Storing the anolyte for 1 week or 1 month at +4°C did not significantly affect power production, but the lag time for power production was increased from 2 days to 3 or 5 days, respectively. One month storing at -20°C increased the lag time to 7 days. The average power density in these MFCs varied between 1.2 and 1.7 W/m³. The share of dead cells (measured by live/dead staining) increased with storing time. After 6-month storage, the power production was insignificant. However, xylose removal remained similar in all cultures (99-100%) while volatile fatty acids production varied. The results indicate that fermentative organisms tolerated the long storage better than the exoelectrogens. As storing at +4°C is less energy intensive compared to freezing, anolyte storage at +4°C for a maximum of 1 month is recommended as start-up seed for MFC after process failure to enable efficient process recovery.

Behavior of two-chamber microbial electrochemical systems started-up with different ion-exchange membrane separators

In this study, microbial fuel cells (MFCs) - operated with novel cation- and anion-exchange membranes, in particular AN-VPA 60 (CEM) and PSEBS DABCO (AEM) - were assessed comparatively with Nafion proton exchange membrane (PEM). The process characterization involved versatile electrochemical (polarization, electrochemical impedance spectroscopy - EIS, cyclic voltammetry - CV) and biological (microbial structure analysis) methods in order to reveal the influence of membrane-type during start-up. In fact, the use of AEM led to 2-5 times higher energy yields than CEM and PEM and the lowest MFC internal resistance (148 ± 17 Ω) by the end of start-up. Regardless of the membrane-type, Geobacter was dominantly enriched on all anodes. Besides, CV and EIS measurements implied higher anode surface coverage of redox compounds for MFCs and lower membrane resistance with AEM, respectively. As a result, AEM based on PSEBS DABCO could be found as a promising material to substitute Nafion.

Monitoring microbial communities' dynamics during the start-up of microbial fuel cells by high-throughput screening techniques

Microbial Electrochemical Technologies are based on the use of electrochemically active microorganisms that can carry out extracellular electron transfer to an electrode while they are oxidizing the organic compounds. The dynamics and changes of the bacterial community in the anode biofilm and planktonic broth of an acetate fed batch single chamber air cathode MFC have been studied by combing flow-cytometry and Illumina sequencing techniques. At the beginning of the test, from 0 h to 70 h, microbial planktonic communities changed from four groups to two groups, as revealed by DNA content, and from three groups to one group based on the cell membrane polarization revealed by a DiOC₆(3) probe. Between 4^th day and 13^th day, microbial communities changed from one group to a maximum of three groups, monitoring DNA content, and from one group to two based on the cell membrane polarization. The 16S rDNA gene profiling confirmed the shift in microbial communities, with Acinetobacter (39.34%), Azospirillum (27.66%), Arcobacter (4.17%) and Comamonas (2.62%) being the most abundant genera at the beginning of MFC activation. After 70 h the main genera detected were Azospirillum (46.42%), Acinetobacter (34.66%), Enterococcus (2.32%), Dysgonomonas (2.14%). Data obtained have shown that flow cytometry and illumina sequencing are useful tools to monitor "online" the changes in microbial communities during the MFCs start-up and the increase of Azospirillum and Acinetobacter genera is in good agreement with the MFC voltage generation. Moreover, monitoring planktonic populations, instead of the less accessible anode biofilm, was in good agreement with the evolution of MFC voltage.

Meta-proteomic analysis of protein expression distinctive to electricity-generating biofilm communities in air-cathode microbial fuel cells

BACKGROUND

Bioelectrochemical systems (BESs) harness electrons from microbial respiration to generate power or chemical products from a variety of organic feedstocks, including lignocellulosic biomass, fermentation byproducts, and wastewater sludge. In some BESs, such as microbial fuel cells (MFCs), bacteria living in a biofilm use the anode as an electron acceptor for electrons harvested from organic materials such as lignocellulosic biomass or waste byproducts, generating energy that may be used by humans. Many BES applications use bacterial biofilm communities, but no studies have investigated protein expression by the anode biofilm community as a whole.

RESULTS

To discover functional protein expression during current generation that may be useful for MFC optimization, a label-free meta-proteomics approach was used to compare protein expression in acetate-fed anode biofilms before and after the onset of robust electricity generation. Meta-proteomic comparisons were integrated with 16S rRNA gene-based community analysis at four developmental stages. The community composition shifted from dominance by aerobic Gammaproteobacteria (90.9 ± 3.3%) during initial biofilm formation to dominance by Deltaproteobacteria, particularly Geobacter (68.7 ± 3.6%) in mature, electricity-generating anodes. Community diversity in the intermediate stage, just after robust current generation began, was double that at the early stage and nearly double that of mature anode communities. Maximum current densities at the intermediate stage, however, were relatively similar (~ 83%) to those achieved by mature-stage biofilms. Meta-proteomic analysis, correlated with population changes, revealed significant enrichment of categories specific to membrane and transport functions among proteins from electricity-producing biofilms. Proteins detected only in electricity-producing biofilms were associated with gluconeogenesis, the glyoxylate cycle, and fatty acid β-oxidation, as well as with denitrification and competitive inhibition.

CONCLUSIONS

The results demonstrate that it is possible for an MFC microbial community to generate robust current densities while exhibiting high taxonomic diversity. Moreover, these data provide evidence to suggest that startup growth of air-cathode MFCs under conditions that promote the establishment of aerobic-anaerobic syntrophy may decrease startup times. This study represents the first investigation into protein expression of a complex BES anode biofilm community as a whole. The findings contribute to understanding of the molecular mechanisms at work during BES startup and suggest options for improvement of BES generation of bioelectricity from renewable biomass.

Improving biocathode community multifunctionality by polarity inversion for simultaneous bioelectroreduction processes in domestic wastewater

Bioelectrochemical systems (BESs) have been tentatively applied for wastewater treatment processes, but the complex composition of wastewater could lead to difficulties in establishing functional biofilm or result in performance instability. Few studies have investigated the enrichment of biocathode with domestic wastewater (DW) and the function. A biocathode with multi-pollutant removal capabilities was enriched based on polarity inverted bioanode, which was established with DW. The biocathode function was examined using model pollutants (nitrate, nitrobenzene and Acid Orange 7) supplemented as sole or mixed electron acceptors. When compared to the anaerobic control treatment, the biofilm demonstrated significantly enhanced reduction abilities in the open circuit. For the closed circuit, their removal efficiencies were further enhanced for both the sole and mixed substrates conditions. The bioanodes community structure and diversity markedly changed after operating for 50 d as biocathodes. The biocathode multifunctionality and stability could be related to the maintenance of organic matters fermentative bacteria (mainly belonging to Bacteroidetes, Firmicutes and Synergistetes) and the enrichment of versatile pollutant-reducing bacteria (e.g. Pseudomonas, Thauera and Comamonas from Proteobacteria). Other pollutants, such as perchlorate, sulfate, heavy metals, and halogenated organics, may also work as potential electron acceptors. This study provides a new strategy to improve the biocathode community multifunctionality for simultaneous bioelectroreduction, which can be combined with other wastewater treatment processes in actual application.

Simulation and resolution of voltage reversal in microbial fuel cell stack

To understand the biotic and non-biotic contributions of voltage reversals in microbial fuel cell stacks (MFC) they were simulated with an electronic MFC-Stack mimic. The simulation was then compared with results from a real 3L triple MFC-Stack with shared anolyte. It showed that voltage reversals originate from the variability of biofilms, but also the external load plays a role. When similar biofilm properties were created on all anodes the likelihood of voltage reversals was largely reduced. Homogenous biofilms on all anodes were created by electrical circuit alternation and electrostimulation. Conversely, anolyte recirculation, or increased nutriment supply, postponed reversals and unfavourable voltage asymmetries on anodes persisted. In conclusion, voltage reversals are often a negative event but occur also in close to best MFC-Stack performance. They were manageable and this with a simplified MFC architecture in which multiple anodes share the same anolyte.

Aerobic granular sludge inoculated microbial fuel cells for enhanced epoxy reactive diluent wastewater treatment

Microbial consortiums aggregated on the anode surface of microbial fuel cells (MFCs) are critical factors for electricity generation as well as biodegradation efficiencies of organic compounds. Here in this study, aerobic granular sludge (AGS) was assembled on the surface of the MFC anode to form an AGS-MFC system with superior performance on epoxy reactive diluent (ERD) wastewater treatment. AGS-MFCs successfully shortened the startup time from 13d to 7d compared to the ones inoculated with domestic wastewater. Enhanced toxicity tolerance as well as higher COD removal (77.8% vs. 63.6%) were achieved. The higher ERD wastewater treatment efficiency of AGS-MFC is possibly attributed to the diverse microbial population on MFC biofilm, as well as the synergic degradation of contaminants by both the MFC anode biofilm and AGS granules.

H2 production in membraneless bioelectrochemical cells with optimized architecture: The effect of cathode surface area and electrode distance

In this work we report on the hydrogen production capacity of single-chamber microbial electrohydrogenesis cell (MEC) with optimized design characteristics, in particular cathode surface area and anode-cathode spacing using acetate as substrate. The results showed that the maximal H₂ production rates and best energetic performances could be obtained using the smallest, 71 cm² stainless steel cathode and 4 cm electrode distances, employing a 60 cm² bioanode. Cyclic voltammetric analysis was employed to investigate the dominant electron transfer mechanism of the architecturally optimized system.

Nitrogen Removal and N2O Accumulation during Hydrogenotrophic Denitrification: Influence of Environmental Factors and Microbial Community Characteristics

Hydrogenotrophic denitrification is regarded as an efficient alternative technology of removing nitrogen from nitrate-polluted water that has insufficient organics material. However, the biochemical process underlying this method has not been completely characterized, particularly with regard to the generation and reduction of nitrous oxide (N₂O). In this study, the effects of key environmental factors on hydrogenotrophic denitrification and N₂O accumulation were investigated in a series of batch tests. The results show that nitrogen removal was efficient with a specific denitrification rate of 0.66 kg N/(kg MLSS·d), and almost no N₂O accumulation was observed when the dissolved hydrogen (DH) concentration was approximately 0.40 mg/L, the temperature was 30 °C, and the pH was 7.0. The reduction of nitrate was significantly affected by the pH, temperature, inorganic carbon (IC) content, and DH concentration. A considerable accumulation of N₂O was only observed when the pH decreased to 6.0 and the temperature decreased to 15 °C, where little N₂O accumulated under various IC and DH concentrations. To determine the microbial community structure, the hydrogenotrophic denitrifying enrichment culture was analyzed by Illumina high-throughput sequencing, and the dominant species were found to belong to the genera Paracoccus (26.1%), Azoarcus (24.8%), Acetoanaerobium (11.4%), Labrenzia (7.4%), and Dysgonomonas (6.0%).

Evaluation of the performance of zero-electrolyte-discharge microbial fuel cell based on the type of substrate

Acetic acid was found to be the most suitable candidate for zero-electrolyte-discharge MFC as it provides stable electrolyte environment and least cathodic biofilm growth.

Community structure dynamics during startup in microbial fuel cells - The effect of phosphate concentrations

For microbial fuel cells (MFCs) to become a cost-effective wastewater treatment technology, they must produce a stable electro-active microbial community quickly and operate under realistic wastewater nutrient conditions. The composition of the anodic-biofilm and planktonic-cells communities was followed temporally for MFCs operated under typical laboratory phosphate concentrations (134mgL(-1)P) versus wastewater phosphate concentrations (16mgL(-1)P). A stable peak voltage was attained two-fold faster in MFCs operating under lower phosphate concentration. All anodic-biofilms were composed of well-known exoelectrogenic bacterial families; however, MFCs showing faster startup and a stable voltage had a Desulfuromonadaceae-dominated-biofilm, while biofilms co-dominated by Desulfuromonadaceae and Geobacteraceae characterized slower or less stable MFCs. Interestingly,planktonic-cell concentrations of these bacteria followed a similar trend as the anodic-biofilm and could therefore serve as a biomarker for its formation. These results demonstrate that wastewater-phosphate concentrations do not compromise MFCs efficiency, and considerably speed up startup times.

Surface-to-surface biofilm transfer: a quick and reliable startup strategy for mixed culture microbial fuel cells

The startup of microbial fuel cells (MFCs) is known to be prone to failure or result in erratic performance impeding the research. The aim of this study was to advise a quick launch strategy for laboratory-scale MFCs that ensures steady operation performance in a short period of time. Different startup strategies were investigated and compared with membraneless single chamber MFCs. A direct surface-to-surface biofilm transfer (BFT) in an operating MFC proved to be the most efficient method. It provided steady power densities of 163 ± 13 mWm(-2) 4 days after inoculation compared to 58 ± 15 mWm(-2) after 30 days following a conventional inoculation approach. The in situ BFT eliminates the need for microbial acclimation during startup and reduces performance fluctuations caused by shifts in microbial biodiversity. Anaerobic pretreatment of the substrate and addition of suspended enzymes from an operating MFC into the new MFC proved to have a beneficial effect on startup and subsequent operation. Polarization methods were applied to characterize the startup phase and the steady state operation in terms of power densities, internal resistance and power overshoot during biofilm maturation. Applying this method a well-working MFC can be multiplied into an array of identically performing MFCs.

A comparative evaluation of different types of microbial electrolysis desalination cells for malic acid production

The aim of this study was to investigate different microbial electrolysis desalination cells for malic acid production. The systems included microbial electrolysis desalination and chemical-production cell (MEDCC), microbial electrolysis desalination cell (MEDC) with bipolar membrane and anion exchange membrane (BP-A MEDC), MEDC with bipolar membrane and cation exchange membrane (BP-C MEDC), and modified microbial desalination cell (M-MDC). The microbial electrolysis desalination cells performed differently in terms of malic acid production and energy consumption. The MEDCC performed best with the highest malic acid production rate (18.4 ± 0.6 mmol/Lh) and the lowest energy consumption (0.35 ± 0.14 kWh/kg). The best performance of MEDCC was attributable to the neutral pH condition in the anode chamber, the lowest internal resistance, and the highest Geobacter percentage of the anode biofilm population among all the reactors.