Human hair-derived high surface area porous carbon material for the adsorption isotherm and kinetics of tetracycline antibiotics

Occurrence and risks of pharmaceuticals, personal care products, and endocrine-disrupting compounds in Chinese surface waters

The continuous and rapid increase of chemical pollution in surface waters has become a pressing and widely recognized global concern. As emerging contaminants (ECs) in surface waters, pharmaceutical and personal care products (PPCPs), and endocrine-disrupting compounds (EDCs) have attracted considerable attention due to their wide occurrence and potential threat to human health. Therefore, a comprehensive understanding of the occurrence and risks of ECs in Chinese surface waters is urgently required. This study summarizes and assesses the environmental occurrence concentrations and ecological risks of 42 pharmaceuticals, 15 personal care products (PCPs), and 20 EDCs frequently detected in Chinese surface waters. The ECs were primarily detected in China's densely populated and highly industrialized regions. Most detected PPCPs and EDCs had concentrations between ng/L to µg/L, whereas norfloxacin, caffeine, and erythromycin had relatively high contamination levels, even exceeding 2000 ng/L. Risk evaluation based on the risk quotient method revealed that 34 PPCPs and EDCs in Chinese surface waters did not pose a significant risk, whereas 4-nonylphenol, 4-tert-octylphenol, 17α-ethinyl estradiol, 17β-estradiol, and triclocarban did. This review provides a comprehensive summary of the occurrence and associated hazards of typical PPCPs and EDCs in Chinese surface waters over the past decade, and will aid in the regulation and control of these ECs in Chinese surface waters.

Photoinduced charge generation of nanostructured carbon derived from human hair biowaste for performance enhancement in polyvinylidene fluoride based triboelectric nanogenerator

Carbon nanostructures derived from human hair biowaste are incorporated into polyvinylidene fluoride (PVDF) polymer to enhance the energy conversion performance of a triboelectric nanogenerator (TENG). The PVDF filled with activated carbon nanomaterial from human hair (AC-HH) exhibits improved surface charge density and photoinduced charge generation. These remarkable properties are attributed to the presence of graphene-like nanostructures in AC-HH, contributing to the augmented performance of PVDF@AC-HH TENG. The correlation of surface morphologies, surface charge potential, charge capacitance properties, and TENG electrical output of the PVDF composites at various AC-HH loading is studied and discussed. Applications of the PVDF@AC-HH TENG as a power source for micro/nanoelectronics and a movement sensor for detecting finger gestures are also demonstrated. The photoresponse property of the fabricated TENG is demonstrated and analyzed in-depth. The analysis indicates that the photoinduced charge carriers originate from the conductive reduced graphene oxide (rGO), contributing to the enhanced surface charge density of the PVDF composite film. This research introduces a novel approach to enhancing TENG performance through the utilization of carbon nanostructures derived from human biowaste. The findings of this work are crucial for the development of innovative energy-harvesting technology with multifunctionality, including power generation, motion detection, and photoresponse capabilities.

Magnetization and ZIF-67 modification of Aspergillus flavus biomass for tetracycline removal from aqueous solutions: A stable and efficient composite

In the present work, the biomass of Aspergillus flavus (AF) was modified using magnetic nanoparticles MnFe2O4 and metal-organic framework of ZIF-67, and its ability to remove tetracycline antibiotic (TCH) was investigated. With the help of physicochemical tests, AF biomass modification with ZIF-67 and MnFe2O4 magnetic nanoparticles was confirmed. Based on the BET value, AF-MnFe2O4-ZIF-67 (139.83 m2/g) has a higher surface value than AF (0.786 m2/g) and AF/MnFe2O4 (17.504 m2/g). Also, the magnetic saturation value revealed that the modified biomass can be isolated from the treated solution using a simple magnetic field. Maximum TCH elimination (99.04%) using AF-MnFe2O4-ZIF-67 was obtained at pH 7, adsorber mass of 1 g/L, adsorption time of 40 min, and TCH content of 10 mg/L. The thermodynamic study indicated that the TCH abatement using the desired composite is spontaneous and exothermic. The experimental results showed that the adsorption process is compatible with the pseudo-second-order kinetic and Freundlich model. The maximum adsorption capacity for AF, AF-MnFe2O4, and AF-MnFe2O4-ZIF-67 was quantified to be 9.75 mg/g, 25.59 mg/g, and 43.87 mg/g, respectively. The reusability of the desired adsorbers was examined in up to 8 steps. The outcomes showed that the adsorbers can be used several times in TCH elimination. The provided composite can remove TCH from hospital wastewater, so it can be suggested for use in water and wastewater treatment works.

Enhancing photocatalytic tetracycline degradation through the fabrication of high surface area CeO2 from a cerium-organic framework

Water pollution is a global environmental issue, and the presence of pharmaceutical compounds, such as tetracyclines (TCs), in aquatic ecosystems has raised growing concerns due to the potential risks to both the environment and human health. A high surface area CeO2 was prepared via atmospheric thermal treatment of a metal-organic framework of cerium and benzene-1,3,5-tricarboxylate. The effects of calcination temperature on the morphology, structure, light absorption properties and tetracycline removal efficiency were studied. The best activity of the photocatalysts could be achieved when the heat treatment temperature is 300 °C, which enhances the photocatalytic degradation performance towards tetracycline under visible light. The resulting CeO2 particles have high capacity for adsorbing TCs from aqueous solution: 90 mg g-1 for 60 mg L-1 TCs. As a result, 98% of the initial TC can be removed under simulated sunlight irradiation. The cooperation of moderate defect concentration and disordered structure showed tetracycline removal activity about 10 times higher than the initial Ce-MOF. An embryotoxicity assessment on zebrafish revealed that treatment with CeO2 particles significantly decreased the toxicity of TC solutions.

Efficacy of new generation biosorbents for the sustainable treatment of antibiotic residues and antibiotic resistance genes from polluted waste effluent

Antimicrobials are frequently used in both humans and animals for the treatment of bacterially-generated illnesses. Antibiotic usage has increased for more than 40% from last 15 years globally per day in both human populations and farm animals leading to the large-scale discharge of antibiotic residues into wastewater. Most antibiotics end up in sewer systems, either directly from industry or healthcare systems, or indirectly from humans and animals after being partially metabolized or broken down following consumption. To prevent additional antibiotic compound pollution, which eventually impacts on the spread of antibiotic resistance, it is crucial to remove antibiotic residues from wastewater. Antibiotic accumulation and antibiotic resistance genes cannot be effectively and efficiently eliminated by conventional sewage treatment plants. Because of their high energy requirements and operating costs, many of the available technologies are not feasible. However, the biosorption method, which uses low-cost biomass as the biosorbent, is an alternative technique to potentially address these problems. An extensive literature survey focusing on developments in the field was conducted using English language electronic databases, such as PubMed, Google Scholar, Pubag, Google books, and ResearchGate, to understand the relative value of the available antibiotic removal methods. The predominant techniques for eliminating antibiotic residues from wastewater were categorized and defined by example. The approaches were contrasted, and the benefits and drawbacks were highlighted. Additionally, we included a few antibiotics whose removal from aquatic environments has been the subject of extensive research. Lastly, a few representative publications were identified that provide specific information on the removal rates attained by each technique. This review provides evidence that biosorption of antibiotic residues from biological waste using natural biosorbent materials is an affordable and effective technique for eliminating antibiotic residues from wastewater.

More movement with manure: increased mobility of erythromycin through agricultural soil in the presence of manure

Antibiotic residues in the environment threaten soil and aquatic organisms and human and livestock health through the building of antimicrobial resistance. Manure spreading associated with animal agriculture is one source of environmental antibiotic residues. To better understand the risk of contamination, we studied the adsorption of erythromycin, a model macrolide antibiotic used across human and animal medicine. We conducted a series of equilibrium batch experiments to determine the kinetics and extent of adsorption and a continuous-flow column adsorption experiment to observe non-equilibrium adsorption patterns. We determined that the adsorption equilibration time to soil was approximately 72 h in our batch experiments. Erythromycin adsorbed to soil relatively strongly (K = 8.01 × 10-2 L/mg; qmax = 1.53 × 10-3 mg/mg), adsorbed to the soil in the presence of manure with less affinity (K = 1.99 × 10-4 L/mg) at a soil: manure ratio of 10:1 by mass, and did not adsorb to manure across the solid ratios tested. We observed multi-phased adsorption of erythromycin to the soil during the non-equilibrium column experiment, which was largely absent from the treatments with both soil and manure present. These results suggest that erythromycin is more mobile in the environment when introduced with manure, which is likely the largest source of agriculturally sourced environmental antibiotics.

A novel BC/g-C3N4 porous hydrogel carrier used in intimately coupled photocatalysis and biodegradation system for efficient removal of tetracycline hydrochloride in water

Intimately coupled photocatalysis and biodegradation (ICPB) is a promising technology to remove refractory contaminants from water. The key to successful ICPB is a carrier capable of accumulating biofilm and adhering photocatalyst firmly. Herein, BC/g-C₃N₄ was prepared into a three dimensional porous hydrogel and used as a carrier in ICPB system for the first time. Degradation experiments revealed that the removal rate of tetracycline hydrochloride (TCH) in water by the ICPB system was 96.0% after 10 h, which was significantly higher than that by the photocatalysis (PC, 76.3%), biodegradation (B, 32.5%), adsorption (AD, 17.2%), and photolysis (P, 5.0%) systems. Photo-electrochemical tests confirmed that ICPB system had superior electron transfer ability between photocatalysts and microorganisms. The removal efficiency of COD proved that microorganisms played an important role in the mineralization process of TCH by the ICPB system. After the ICPB degradation experiment, microorganisms maintained high activity and Pseudomonas, Burkholderiaceae and Flavobacterium which had TCH degradation or electron transport ability, were enriched. In conclusion, the novel ICPB carrier overcame shortcomings of the traditional ICPB carrier and the novel ICPB system had superior degradation performance for TCH. This study provided a possible method to promote the practical application of ICPB technology.

Carbonised Human Hair Incorporated in Agar/KGM Bioscaffold for Tissue Engineering Application: Fabrication and Characterisation

Carbon derived from biomass waste usage is rising in various fields of application due to its availability, cost-effectiveness, and sustainability, but it remains limited in tissue engineering applications. Carbon derived from human hair waste was selected to fabricate a carbon-based bioscaffold (CHAK) due to its ease of collection and inexpensive synthesis procedure. The CHAK was fabricated via gelation, rapid freezing, and ethanol immersion and characterised based on their morphology, porosity, Fourier transforms infrared (FTIR), tensile strength, swelling ability, degradability, electrical conductivity, and biocompatibility using Wharton’s jelly-derived mesenchymal stem cells (WJMSCs). The addition of carbon reduced the porosity of the bioscaffold. Via FTIR analysis, the combination of carbon, agar, and KGM was compatible. Among the CHAK, the 3HC bioscaffold displayed the highest tensile strength (62.35 ± 29.12 kPa). The CHAK also showed excellent swelling and water uptake capability. All bioscaffolds demonstrated a slow degradability rate (<50%) after 28 days of incubation, while the electrical conductivity analysis showed that the 3AHC bioscaffold had the highest conductivity compared to other CHAK bioscaffolds. Our findings also showed that the CHAK bioscaffolds were biocompatible with WJMSCs. These findings showed that the CHAK bioscaffolds have potential as bioscaffolds for tissue engineering applications.

Hydrophobic Modification of ZrO2-SiO2 Xerogel and Its Adsorption Properties to Rhodamine B

Zirconium nitrate pentahydrate (Zr(NO₃)₄·5H₂O) and tetraethyl orthosilicate (TEOS) are used as the zirconium source and silicon source, respectively, and methyltriethoxysilane (MTES) as the hydrophobic modifier; the hydrophilic and hydrophobic ZrO₂-SiO₂ xerogels were prepared successfully. The xerogels were characterized using Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ adsorption-desorption measurement. The adsorption mechanism of hydrophobic ZrO₂-SiO₂ xerogels to RhB was described by the kinetic and adsorption isotherms. The results showed that the introduction of Si-CH₃ groups can make the average pore size, BET surface area, and total pore volume of ZrO₂-SiO₂ xerogel increase. The hydrophobic ZrO₂-SiO₂ xerogel displays an adsorption capacity of 169.23 mg·g^-1 for RhB dye at 25 °C and pH = 3. The adsorption process of hydrophobic ZrO₂-SiO₂ xerogel to RhB followed a pseudo-second-order kinetic model. Fitting results from the D-R model of adsorption indicate that the adsorption of RhB onto the hydrophobic ZrO₂-SiO₂ xerogels is mainly physical, accompanied by a spontaneous heat absorption process. The regeneration and recycling properties of hydrophobic xerogels were investigated, and their recoverability and reusability were demonstrated.

Three‐dimensional nanoporous activated carbon electrode derived from acacia wood for high‐performance supercapacitor

Herein, the novel acacia wood based hierarchical porous activated carbons (AWCs) are easily prepared, low cost and have excellent characterization, such as special biomass nanopores via structural stability and large specific surface areas. Activating agents such as KOH, ZnCl2, and H3PO4 have been used to convert acacia wood carbon into active carbons such as AWC-K, AWC-Z, and AWC-P, respectively, which are named after the activating agent. As a supercapacitor electrode, the AWC-K sample has a high yield was 69.8%, significant specific surface area of 1563.43 m2g−1 and layer thickness of 4.6 mm. Besides that, it showed specific capacitance of 224.92 F g−1 at 0.5 A g−1 in 2 M KOH as electrolyte. In addition, the AWC-K//AWC-K symmetrical supercapacitor device displays high energy density of 23.98 Wh kg−1 at 450 W kg−1 power density with excellent cycling number stability was 93.2% long lifetime of 10,000 cycles using 0.5 M Na2SO4 as electrolyte. The high electrochemistry performance mainly contributed the special biomass pores structure. Therefore, the presented approach opens new avenues in supercapacitor applications to meet energy storage.

Porous activated carbons derived from bamboo pulp black liquor for effective adsorption removal of tetracycline hydrochloride and malachite green from water

As a kind of wastewater produced by papermaking industry, bamboo pulp black liquor (BPBL) discharged into water causes serious environmental problems. In this work, BPBL was successfully converted into porous carbon after activation with potassium hydroxide (KOH) through one-step carbonization, and adsorption properties of porous carbon derived from bamboo pulp black liquor (BLPC) for tetracycline hydrochloride (TCH) and malachite green (MG) were studied. The adsorption capacities of BLPC for TCH and MG are 1047 and 1277 mg/g, respectively, due to its large specific surface area of 1859.08 m²/g. Kinetics and isotherm data are well fitted to the pseudo-second-order rate model and Langmuir model, respectively. Adsorption experiments and characterizations reveal that the adsorption mechanism involved in TCH and MG adsorption on BLPC mainly depends on the synergistic effect of pore filling, H-bonding, π-π interactions and weak electrostatic interactions. In addition, BLPC shows excellent photothermal properties, and the adsorption capacity of TCH and MG on BLPC can reach 584 and 847 mg/g under the irradiation of near infrared lamp for 50 min, respectively. The synthesized BLPC with high adsorption efficiency, good recovery ability, improved adsorption under near-infrared irradiation can be a promising and effective adsorbent for TCH or MG or other pollutes.

Valorization of Human Hair and Its Derivatives in Tissue Engineering: A Review

Human hair is a potential biomaterial for biomedical applications. Improper disposal of human hair may pose various adverse effects on the environment and human health. Therefore, proper management of human hair waste is pivotal. Human hair fiber and its derivatives offer various advantages as biomaterials such as biocompatibility, biodegradability, low toxicity, radical scavenging, electroconductivity, and intrinsic biological activity. Therefore, the favorable characteristics of human hair have rendered its usage in tissue engineering (TE) applications including skin, cardiac, nerve, bone, ocular, and periodontal. Moreover, the strategies by utilizing human hair as a biomaterial for TE applications may reduce the accumulation of human hair. Thus, it also improves human hair waste management while promoting natural, environmental-friendly, and nontoxic materials. Furthermore, promoting sustainable materials production will benefit human health and well-being. Hence, this article reviews and discusses human hair characteristics as sustainable biomaterials and their recent application in TE applications. Impact Statement This review article highlights the sustainability aspects of human hair as raw biomaterials and various elements of human hair that could potentially be used in tissue engineering (TE) applications. Furthermore, this article discusses numerous benefits of human hair, highlighting its value as biomaterials in bioscaffold development for TE applications. Moreover, this article reviews the role and effect of human hair in various TE applications, including skin, cardiac, nerve, bone, ocular, and periodontal.

Sensitivity Analysis with the Monte Carlo Method and Prediction of Atenolol Removal Using Modified Multiwalled Carbon Nanotubes Based on the Response Surface Method: Isotherm and Kinetics Studies

Atenolol (ATN) is a β-blocker drug extensively used to treat arrhythmias and high blood pressure. Because the human body cannot metabolize it completely, this drug has been commonly found in many environmental matrices. In the present study, the response surface method (RSM) was used for adsorption prediction of ATN on modified multiwalled carbon nanotubes (M-MWCNTs) by NaOCl and ultrasonic. The sensitivity analysis was done by the Monte Carlo method. Sensitivity analysis was performed to determine the effective parameter by the Monte Carlo simulator. Statistical analysis of variance (ANOVA) was performed by using the nonlinear second-order model of RSM. The influential parameters including contact time (min), adsorbent dosage (g/L), pH, and the initial concentration (mg/L) of ATN were investigated, and optimal conditions were determined. Kinetic of ATN adsorption on M-MWCNTs was evaluated using pseudo-first, pseudo-second-order, and intraparticle diffusion models. Equilibrium isotherms for this system were analyzed by the ISOFIT software. As per our result, optimum conditions in the adsorption experiments were pH 7, 60 min of contact time, 0.5 mg/L ATN initial concentration, and 150 mg/L adsorbent dose. In terms of ATN removal efficiency, coefficients of R2 and adjusted R2 were 0.999 and 0.998, respectively. Sensitivity analysis also showed that contact time has the greatest effect on increasing the removal of ATN. Pseudo-first-order (R2 value of 0.99) was the best kinetic model for the adsorption of ATN, and for isotherm, BET (AICC value of 3.27) was the best model that fit the experimental data. According to the obtained results from sensitive analysis, time was the most important parameter, and after that, the adsorbent dose and pH affect positively on ATN removal efficiency. It can be concluded that the modified multiwalled carbon nanotubes can be applied as one of the best adsorbents to remove ATN from the aqueous solution.

Seaweed-derived hierarchically porous carbon for highly efficient removal of tetracycline

Herein we present a facile approach for the preparation of a novel hierarchically porous carbon, in which seaweeds serve as carbon source and KOH as activator. The fabricated KOH-activated seaweed carbon (K-SC) displays strong affinity towards tetracycline with maximum uptake quantity of 853.3 mg/g, significantly higher than other tetracycline adsorbents. The superior adsorption capacity ascribes to large specific surface area (2614 m2/g) and hierarchically porous structure of K-SC, along with strong π- π interactions between tetracycline and K-SC. In addition, the as-prepared K-SC exhibits fast adsorption kinetics, capable of removing 99% of tetracycline in 30 min. Meanwhile, the exhausted K-SC can be regenerated for four cycling adsorption without an obvious degradation in capacities. More importantly, pH and ionic strengths barely affect the adsorption performance of K-SC, implying electrostatic interactions hardly play any role in tetracycline adsorption process. Furthermore, the K-SC packed fixed-bed column (0.1 g of adsorbents) can continually treat 2780 mL solution spiked with 5.0 mg/g tetracycline before reaching the breakthrough point. All in all, the fabricated K-SC equips with high adsorption capacity, fast adsorption rate, glorious anti-interference capability and good reusability, which make it hold great feasibilities for treating tetracycline contamination in real applications.

Excellent Electrocatalytic Hydrogen Evolution Reaction Performances of Partially Graphitized Activated-Carbon Nanobundles Derived from Biomass Human Hair Wastes

Carbonaceous materials play a vital role as an appropriate catalyst for electrocatalytic hydrogen production. Aiming at realizing the highly efficient hydrogen evolution reaction (HER), the partially graphitized activated-carbon nanobundles were synthesized as a high-performance HER electrocatalyst by using biomass human hair ashes through the high-temperature KOH activation at two different temperatures of 600 and 700 °C. Due to the partial graphitization, the 700 °C KOH-activated partially graphitized activated-carbon nanobundles exhibited higher electrical conductivity as well as higher textural porosity than those of the amorphous activated-carbon nanobundles that had been prepared by the KOH activation at 600 °C. As a consequence, the 700 °C-activated partially graphitized activated-carbon nanobundles showed the extraordinarily high HER activity with the very low overpotential (≈16 mV at 10 mA/cm² in 0.5 M H₂SO₄) and the small Tafel slope (≈51 mV/dec). These results suggest that the human hair-derived partially graphitized activated-carbon nanobundles can be effectively utilized as a high-performance HER electrocatalyst in future hydrogen-energy technology.

Obtaining high-value nitrogen-containing carbon nanosheets with ultrahigh surface area from waste sludge for energy storage and wastewater treatment

Recovering high value-added resources from waste activated sludge (WAS) is a potential way for the sustainable wastewater treatment. In this study, hydrothermal treatment at 180 °C was used to simultaneously improve sludge dewaterability and recover sludge organic matters (SOMs). The recovered SOMs were subsequently employed as precursors to prepare nitrogen-doped porous carbon nanosheets via a facile stepwise synthesis method. The as-prepared optimal carbon (AP-SOM₈₀₀) was characterized with an ultrahigh specific surface area (3473 m²/g), appropriate porosity (1.77 cm³/g), and abundant heteroatoms (1.47% N and 7.44% O). AP-SOM₈₀₀ exhibited a high specific capacitance (409 F/g at 0.25 A/g), low resistance (0.52 Ω), and superior cyclic stability (only 9.09% loss after 10,000 cycles) in 6 M KOH aqueous electrolyte. Furthermore, AP-SOM₈₀₀ demonstrated an extraordinary adsorption capacity (1528 mg/g for methyl orange (MO) and 1265 mg/g for tetracycline (TC)) that can be maintained (˃ 1200 mg/g) over a wide range of pH conditions. Specifically, 80.97% of MO and 66.67% of TC were rapidly absorbed through AP-SOM₈₀₀ within 10 min, and 90.27% of MO and 81.24% of TC were eventually removed from wastewater after 60 min. The adsorption processes fit closely with the pseudo-second-order kinetic (R² > 0.999) and Langmuir models (R² > 0.914), revealing that the adsorption processes were dominated by a monolayer chemical adsorption reaction. This study suggests that high value-added materials can be obtained from the WAS through improving and extending the traditional sludge treatment processes, which will enrich the technical options available for future sustainable sludge treatment and disposal.

Adsorption Characteristics and Molecular Simulation of Malachite Green onto Modified Distillers’ Grains

Adsorbent material was prepared using distillers’ grains (DG), which is a waste product of distilleries. The DG was pre-treated with NaOH and esterification-modified with CS2, which is a commonly used anionic modifier. The structure and morphology of the adsorbent was characterized by FTIR, XRD, EDS, SEM, BET, and zeta potential. The related mechanism of adsorption of malachite green (MG) onto modified distiller’s grains (MDG) was studied by adsorption experiments and molecular simulation techniques. The experimental results showed that CS2 successfully modified the DG fiber, and simultaneously yielded the MDG with a uniform pore distribution. MDG had a considerable adsorption capacity of 367.39 mg/g and a maximum removal rate of 96.51%. After eight adsorption–desorption cycle experiments, the adsorption removal rate of MDG to MG dye remained at 82.6%. The adsorption process could be fitted well by a pseudo-second-order kinetic model (the correlation coefficient R2 > 0.998) and Freundlich isotherm adsorption equation (the correlation coefficient R2 > 0.972). Moreover, the adsorption of MG dye by MDG is a spontaneous, endothermic, and increased entropy process. The results of molecular simulation showed that the mechanism of MG molecules onto MDG was mainly chemical adsorption. The adsorption performance of MG onto MDG was better and more stable than DG. Molecular simulation also provided a theoretical guidance of MDG adsorption–desorption for the research on recycling of DG resources.

Performance of wild plants-derived biochar in the remediation of water contaminated with lead: sorption optimization, kinetics, equilibrium, thermodynamics and reusability studies

This study aims to investigate the sorptive performance of Pb(II) from water of a novel biochar (WPC) produced by fast pyrolysis under anoxic conditions of wild plants (WP). The maximum Pb(II) sorption capacity of WPC is 50.25 mg/g under determined optimum conditions, which are solution pH 5.0, WPC dose 50 mg, contact time 180 min and solution temperature 50 °C. The sorption kinetics and isotherm data were observed to fit well with the Ho-McKay and Langmuir models, respectively. The thermodynamic parameters (ΔG^o, ΔH^o and ΔS^o) calculated for the WPC-Pb(II) sorption system showed that the process was spontaneous and endothermic. The Pb(II) desorption and regeneration studies of WPC with different desorbent agents was also performed. The findings in this study showed that WP can be used as an abundant precursor in the production of very low cost and eco-friendly biochar, and also that its biochar can be used as an environmentally-friendly sorbent in wastewater treatment. Novelty statementWith increasing population and developing industry in the world, agriculture and industrial wastes are increasing. These wastes create environmental and water pollution and adversely affect the health of living things. Efforts to eliminate these negativities have a negative impact on the world economy. For this purpose, various improvement methods are applied. However, the adsorption method is widely used due to its ease of application, efficiency and economic. In order to make this method more economical, many researchers have carried out researches on the preparation of low-cost adsorbents, especially from vegetable wastes.The novelty of this study is the first reporting to use wild plants as a sustainable precursor to produce a low-cost biochar using the traditional pyrolysis method and to examine its adsorption performance for Pb(II) ion removal from water. I believe that if this study is published, it will create a paradigm in environmental improvement studies on wild plants evaluation.

Effectively removing tetracycline from water by nanoarchitectured carbons derived from CO2: Structure and surface chemistry influence

Understanding of the correlation between physico-chemical property of adsorbent and the adsorption performance of contaminant is very significant for developing high-efficient materials to remove antibiotic contamination from water. In this work, a novel kind of carbon adsorbent (EC) derived from CO₂ and activated ECs with modified structure via a facile chemical method using H₂ and KOH were prepared. The synthetic carbon materials (EC, EC-H₂, and EC-KOH) were then applied to remove tetracycline (TC). The kinetics of adsorption for these three carbon materials all well fitted the pseudo-second-order kinetic model. The experimental data of adsorption isotherm had good compatibility with Langmuir and Freundlich models (R² > 0.90), but the Temkin model was the most applicable for all adsorbents (R² > 0.98). A super-high adsorption capacity of EC-KOH obtained from Langmuir fitting was 933.56 mg g^-1, which was much higher than that of EC-H₂ (538.91 mg g^-1) and EC (423.30 mg g^-1), possibly due to its larger specific surface area (S_BET), pore volume, and specific surface chemical structure. Moreover, it was found that surface functional groups and large aperture of adsorbents had a positive effect on adsorption rate. More adsorption sites and surface functional groups of adsorbents were beneficial to enhance the adsorption affinity. These results are of great benefit to the directional control of carbon structure to increase the adsorption performance in rate, capacity, and affinity of antibiotics.

Influence of hydraulic loading rate on antibiotics removal and antibiotic resistance expression in soil layer of constructed wetlands

Behavior of veterinary antibiotics, the corresponding resistant genes in soil layer of constructed wetlands (red soil), and their response to different hydraulic loading rates (HLR) (2, 5, and 10 cm/d) were investigated. Results indicated that the soil layer had perfect performance for oxytetracycline and ciprofloxacin, yet sulfamethazine removal was unsatisfactory. Detection rates of oxytetracycline, ciprofloxacin and sulfamethazine in the effluent of simulation systems of soil layer were 8.33-36.36%, 8.33-47.83% and 100%, respectively. The model analysis of adsorption and hydrolysis indicated that physical adsorption, which was controlled by exchange reaction process based on diffusion, was the primary adsorption mechanism of target antibiotics in red soil, and the hydrolysis half-life values of antibiotics in the water of soil layer were shorter than them in wastewater. The removal response of oxytetracycline and ciprofloxacin to change of HLR was insignificant, yet the respective effluent concentrations of sulfamethazine at HLR of 2-10 cm/d were 41.90, 61.35 and 73.54 μg/L during treating synthetic livestock wastewater, which revealed significant positive correlation (P < 0.05). The relative abundances of each target resistance genes in soil showed significant increase after treating wastewater (10^-5-10^-6 to 10^-4-10^-1), and the total level of those at different HLRs (2, 5, and 10 cm/d) were 3.02 × 10^-2, 7.54 × 10^-2 and 8.65 × 10^-1, respectively. In summary, HLR could affect the removal efficiency of partial antibiotic in soil layer of constructed wetlands, and the expression of antibiotic resistance in the soil gradually increased with increase in the HLR.

Purification of malachite green as a model biocidal agent from aqueous system by using a natural widespread coastal biowaste (Zostera marina)

The present paper aimed to perform an environmentally friendly and effective study on the purification of biocidal material using bioremediation technique, and in this context, a natural widespread coastal biowaste (Zostera marina) was applied to remove a model biocide from aqueous system. Herein, malachite green was selected as a common agent to evaluate the biosorption efficiency of waste biomaterial. The bioremediation properties of biosorbent were studied in a controlled batch experiment system by the optimization practice of operating parameters like biosorbent quantity, medium pH, time, pollutant concentration and temperature, and kinetic, thermodynamic, equilibrium, and characterization operations. The optimum operating conditions were considered as 10 mg, 4, 6 h, 15 mg L^-1, and 25 °C, respectively. Elovich and Langmuir were found to be the best-fitted models, describing the experimental biosorption data. Thermodynamic study revealed a favorable nature of the cleanup process. The characterization analysis indicated the presence of various functional groups on the layered biosorbent surface involved on the pollutant treatment. The untreated biosorbent showed a good biocide purification performance with a value of 97.584 mg g^-1, and it could thus be employed as an eco-friendly and cost-effective cleaning agent in environmental bioremediation studies.

Preparation of porous biochar based on pharmaceutical sludge activated by NaOH and its application in the adsorption of tetracycline

In this study, two different kinds of pharmaceutical sludge activated by NaOH were used to prepare biochar. The characteristics of biochar prepared by impregnation method and dry mixing method were analyzed, including N₂ adsorption-desorption isotherms, surface functional group analysis and micromorphological observation. The results showed that the biochar prepared by impregnation method had more micropores, while that prepared by dry mixing activation method had more mesopores. The adsorption reaction of tetracycline on the two different kind of biochar was investigated. Several important factors such as solution initial pH, tetracycline concentration and reaction time on adsorption reaction were investigated. The results show that both kinds of biochar have high tetracycline adsorption efficiency and excellent pH adaptability. The biochar manufactured by dry mixing activation method had better adsorption performance (379.78 mg/g, 25 °C). Regeneration experiments showed that the adsorbent had stable performance in absorbing tetracycline. Direct dry mixing activation method is a simple and effective method used to prepare porous biochar, which can be used for the resourceful utilization of pharmaceutical sludge. This work provides extensive information on the use of biochar derived from pharmaceutical sludge for the removal of TC from hospital and pharmaceutical production wastewater.

A batch study on the adsorption/desorption behavior of vancomycin on bentonite nanoparticles in aqueous solutions

In this study, adsorption/desorption of vancomycin (VAN) on bentonite nanoparticles was investigated in a batch system. Adsorption experiments were carried out as a function of several influential parameters such as adsorbent dosage, pH, contact time and ionic strength. Bentonite nanoparticles were characterized by field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer-Emmett-Teller, and Fourier transform infrared (FTIR) analyses and the mesoporous structure was revealed. Langmuir, Freundlich, and Temkin isotherm models were applied for the examination of equilibrium data, and Langmuir was found to be the best fit. With the increase in pH and ionic strength, the adsorption capacity decreases, which suggests the adsorption process may be dominated by the cation exchange mechanism. Moreover, VAN desorption from bentonite nanoparticles in two initial VAN loadings was investigated under different concentrations of metallic cations of various valences (Na⁺, Ca²⁺, Al³⁺), and pHs 3-10. Desorption was strongly pH-dependent and the amount of VAN desorbed increased with increasing cations concentrations. The FTIR analysis before and after VAN desorption suggests that the formation of Al-VAN and Ca-VAN complexes on the solid surface and then their detachment from the solid surface may contribute to the higher VAN desorption by Al³⁺ and Ca²⁺.

Simple and Eco-Friendly Route from Agro-Food Waste to Water Pollutants Removal

The current study reflects the demand to mitigate the environmental issues caused by the waste from the agriculture and food industry. The crops that do not meet the supply chain requirements and waste from their processing are overfilling landfills. The mentioned wastes contain cellulose, which is the most abundant carbon precursor. Therefore, one of the possibilities of returning such waste into the life cycle could be preparing the activated carbon through an eco-friendly and simple route. Herein, the carrot pulp from the waste was used. Techniques such as thermogravimetric analysis (TGA), elemental analysis (EA), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, and x-ray diffraction (XRD) were used to investigate the thermal treatment effect during the carbon material preparation. The development of microstructure, phase formation, and chemical composition of prepared material was evaluated. The obtained carbon material was finally tested for water cleaning from a synthetic pollutant such as rhodamine B and phloxine B. An adsorption mechanism was proposed on the base of positron annihilation lifetime spectroscopy (PALS) results and attributed to the responsible interactions. It was shown that a significant carbon sorbent from the organic waste for water purification was obtained.

Adsorption isotherm models: Classification, physical meaning, application and solving method

Adsorption is widely applied separation process, especially in environmental remediation, due to its low cost and high efficiency. Adsorption isotherm models can provide mechanism information of the adsorption process, which is important for the design of adsorption system. However, the classification, physical meaning, application and solving method of the isotherms have not been systematical analyzed and summarized. In this paper, the adsorption isotherms were classified into adsorption empirical isotherms, isotherms based on Polanyi's theory, chemical adsorption isotherms, physical adsorption isotherms, and the ion exchange model. The derivation and physical meaning of the isotherm models were discussed in detail. In addition, the application of the isotherm models were analyzed and summarized based on over 200 adsorption equilibrium data in literature. The statistical parameters for evaluating the fitness of the models were also discussed. Finally, a user interface (UI) was developed based on Excel software for solving the isotherm models, which was provided in supplemental material and can be easily used to model the adsorption equilibrium data. This paper will provide theoretical basis and guiding methodology for the selection and use of the adsorption isotherms.

Methanol-modified ultra-fine magnetic orange peel powder biochar as an effective adsorbent for removal of ibuprofen and sulfamethoxazole from water

The efficient capture of drug metabolites from aquatic environments has been recognized as an essential task for environmental protection. A methanol-modified ultra-fine magnetic biochar (CH3OH-OP-char/Fe3O4) was prepared from orange peel powder using ball milling, and its adsorption behaviors for ibuprofen and sulfamethoxazole were evaluated. The obtained materials were characterized by laser particle size analyzer, EA, ICP-OES, VSM, BET, TG-DTG, and FTIR. Furthermore, the experiments were conducted to study the vital operating parameters such as solution pH (2.0–11.0), contact time (0.5–240 min), initial drug concentration (0.5–100 mg/L), and temperatures (15–40°C) on the removal process. The results showed that the adsorption of IBP and sulfamethoxazole on CH3OH-OP-char/Fe3O4 was highly pH-dependent. Kinetic studies indicated that physisorption was the dominant adsorption mechanism, and film diffusion played a vital role in adsorption onto CH3OH-OP-char/Fe3O4. Equilibrium data were fitted well with the Langmuir isotherm model, implying monolayer adsorption. The adsorption process was spontaneous and endothermic due to the thermodynamic calculation, and high temperatures were favorable to the adsorption process.

Removal of antibiotic from the water environment by the adsorption technologies: a review

Antibiotics are known as emergent pollutants because of their toxicological properties. Due to continuous discharge and persistence in the aquatic environment, antibiotics are detected almost in every environmental matrix. Therefore antibiotics that are polluting the aquatic environment have gained significant research interest for their removal. Several techniques have been used to remove pollutants, but appropriate technology is still to be found. This review addresses the use of modified and cheap materials for antibiotic removal from the environment.

An Effectual Biosorbent Substance for Removal of Manganese Ions from Aquatic Environment: A Promising Environmental Remediation Study with Activated Coastal Waste of Zostera marina Plant

In the present research paper, a biosorptive remediation practice for an aqueous medium sample polluted with manganese ions was implemented using the activated coastal waste of the Zostera marina plant. This is the first report in the literature on the utilization of current modified biological waste as a biosorbent substance for the removal of manganese ions from the water environment. The analyses of biosorbent characterization, environmental condition, kinetic, equilibrium, and comparison were performed to introduce the ability of prepared biosorbent for the removal of manganese from the aquatic medium. The biosorbent matter has a rough surface with numerous cavities and cracks and various functional groups for the biosorption of manganese. The environmental conditions significantly affected the manganese purification process, and the optimum working conditions were determined to be biosorbent quantity of 10 mg, pH of 6, manganese concentration of 30 mg L^-1, and time of 60 min. The pseudo-second-order model best explained the kinetic data of biosorption operation. The biosorption equilibrium data were best described by the Freundlich isotherm. According to the Langmuir equilibrium model, the maximum purification potency was estimated to be 120.6 mg g^-1. The comparison work revealed that the activated coastal waste of the Z. marina plant could be utilized as an effectual and promising biosorbent substance for the remediation of an aquatic environment contaminated with manganese ions.

Sustainable environmental remediation approach for biocide removal from water medium: a model biosorption study using activated biological waste

Within the scope of sustainable environmental remediation approach, a biosorbent prepared from the waste of Zostera marina coastal plant with chemical activation was used to effectively remove malachite green as a common biocidal agent from water environment in this work. The biocide treatment ability of activated biosorbent was interpreted through the characterization, optimization, equilibrium, thermodynamic, and kinetic studies. The characterization research showed that the biosorbent has an uneven surface and various active groups for the retention of biocide molecules. Langmuir isotherm was found to be the most appropriate model for the experimental equilibrium data. The maximum monolayer biosorption capacity was obtained as 103.834 mg g^-1 under the optimum conditions (time of 6 h, pH of 4, temperature of 25 °C, biosorbent amount of 10 mg, and biocide concentration of 15 mg L^-1). The biosorption system was determined to be spontaneous and exothermic in thermodynamic aspect. The experimental kinetic data were best described by the pseudo-second-order model. All these results indicated that the activated biological residue could be used as an environmentally friendly and effective biosorbent for the biocide removal from water environment in a sustainable way.

Using of magnetized and non-magnetized tomato industrial processing solid waste in remediation of Reactive Blue 19 dye aqueous solution

In this study, the removal performance of the Reactive Blue 19 (RB19) dye of the magnetized and non-magnetized industrial tomato solid waste (TW) from the aqueous medium was investigated. The properties of the prepared TW and magnetically modified TW (MTW) bio-sorbents were illuminated using XRD, BET, SEM, VSM, FT-IR and Boehm titration analysis techniques. The optimal conditions for sorption of RB19 by both sorbents were identified. The kinetics and equilibrium data of RB19 sorption by both sorbents were found to match the pseudo-second-order kinetic and Langmuir isotherm models, respectively, with high correlation coefficients. The maximum RB19 sorption capacity under the optimum conditions determined by TW and MTW was determined as 38.76 and 58.14 mg/g, respectively. Thermodynamic parameters calculated for RB19 sorption by both sorbents showed that the processes were spontaneous and exothermic.

Distribution and potential risk assessment of antibiotic pollution in the main drinking water sources of Nanjing, China

The distribution character of 41 antibiotics belonging to 6 groups, sulfonamides (SAs), quinolones (QUs), tetracyclines (TCs), macrolides (MLs), penicillins (PLs), and chloramphenicol (CHL), was investigated in drinking water sources of Nanjing during 2017-2019. MLs (42.98%) were the most abundant category, followed by SAs (25.94%) and QUs (22.52%). The dominant antibiotic was ofloxacin (OFX) in Dec. 2017 (average concentration, 3.14 ng/L; range, ND-35.20 ng/L) and Nov. 2018 (2.16 ng/L, ND-12.26 ng/L), and sulfadiazine (SDZ) in Mar. 2019 (16.37 ng/L, ND-25.90 ng/L). For Dec. 2017, the total concentrations in Zhongshan Waterworks (S15) and Jinniushan Reservoir (S16) were significantly higher than the other sampling sites, which may be attributed to point source pollution. The ecological and human risk of the main antibiotics was assessed by risk quotients (RQs) and target hazard quotient (THQ), respectively. Most of the RQ values were below 0.1, except enrofloxacin (ERX, 0.11) and enoxacin (ENX, 0.62) in Dec. 2017, lomefloxacin (LOM, 0.14) in Nov. 2018, and LOM (0.28) and ERX (0.10) in Mar. 2019. This indicated that the risk of the target antibiotics to aquatic organisms in the 3 years was moderate or low level. Meanwhile, results of the THQ values showed that antibiotic exposure caused no risk to human health. This research provides scientific information for antibiotic pollution control and enriches environmental monitoring data in the drinking water sources.

ZIF-mediated N-doped hollow porous carbon as a high performance adsorbent for tetracycline removal from water with wide pH range

The N-doped porous carbon (NPC) and N-doped hollow porous carbons (NHPC-1 and NHPC-2) were fabricated using ZIF-8 and its composites (resorcinol and formaldehyde coated ZIF-8, ZIF-8@RF and tannic acid coated ZIF-8, ZIF-8@TA) as precursors via high-temperature pyrolysis and their applications for removing tetracycline (TC) from water were investigated. The various technologies, including SEM, TEM, FT-IR, Raman, N₂ adsorption-desorption, XRD and XPS were used to characterize the morphology, textual property, phase and microstructure of three porous carbon materials. The adsorption isotherms and kinetics of TC on three porous carbon materials were fitted well with Langmuir model and pseudo-2nd order model, respectively. In terms of the Langmuir model, the maximum TC adsorption capacities on the NPC, NHPC-1 and NHPC-2 were 180.2, 284.9 and 518.1 mg g^-1 at 25 °C, respectively. The excellent performance of NHPC-2 for TC removal is mainly attributed to the suitable pore size distribution and pore volume, high nitrogen contents and large amounts of defects. High TC adsorption was achieved in 3-10 pH range and hardly affected by humic acid. TC adsorption on NHPC-2 is spontaneous and endothermic process. The NHPC-2 kept excellent TC adsorption capacity even after eight cycles, showing its good repeatability. Our result indicates that the MOF-mediated N-doped hollow porous carbon is promising for the TC removal from aqueous media.

Adsorption of Tetracycline by Shrimp Shell Waste from Aqueous Solutions: Adsorption Isotherm, Kinetics Modeling, and Mechanism

The highly efficient removal of tetracycline (TC) from an aqueous solution was accomplished by using the raw shrimp shell waste (SSW) as an environmentally friendly adsorbent. The SSW without any treatment removed TC more efficiently than the SSW after being treated with HCl and NaOH solutions. The SSW was characterized using nitrogen adsorption-desorption isotherms, scanning electron microscopy alongside energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, a thermogravimetric-derivative thermogravimetry analyzer, and a ζ-potential analyzer. The maximum adsorption capacity of 400 mg/L SSW was 229.98 mg/g for 36 h at 55 °C. Both the Langmuir isotherm model and the pseudo-second-order kinetic model well described the experimental data. According to the values of the Gibbs free energy and enthalpy changes, the TC adsorption by SSW proved to be spontaneous and endothermic. The TC adsorption process was controlled by intraparticle diffusion and liquid film diffusion.

An Efficient Photocatalyst Based on Black TiO2 Nanoparticles and Porous Carbon with High Surface Area: Degradation of Antibiotics and Organic Pollutants in Water

Porous carbon (PC) materials with high surface area can separate electron-hole pairs and adsorb organic pollutants more effectively. A series of nanocomposites were prepared by anchoring black TiO₂ nanoparticles (BTN) onto PC through a calcination process. Chemical and structural features of samples were examined by X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, powder X-ray diffraction (P-XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses. The resulting adsorption-photocatalysis synergistic effect led to a dramatically improved photocurrent for BTN@PCs, thus indicating the high photocatalytic performance toward water-soluble organic species. For instance, the degradation of tetracycline under visible light reached 90 %, which is higher than that for activated carbon doped onto BTN (57 %) without any additional agents. Moreover, the degradation of other antibiotics (such as oxytetracycline and ciprofloxacin) and methylene blue were also studied, thus showing that this system has the potential to be used for water treatment.

Removal of Pharmaceutical Contaminants in Wastewater Using Nanomaterials: A Comprehensive Review

BACKGROUND

The limitless presence of pharmaceutical contaminants in discharged wastewater has emerged as a threat to aquatic species and humans. Their presence in drinking water has although raised substantial concerns, very little is known about the fate and ecological impacts of these pollutants. As a result, these pollutants are inevitably introduced to our food chain at trace concentrations. Unfortunately, the conventional wastewater treatment techniques are unable to treat pharmaceuticals completely with practical limitations. The focus has now been shifted towards nanotechnology for the successful remediation of these persistent pollutants. Thus, the current review specifically focuses on providing readers brief yet sharp insights into applications of various nanomaterials for the removal of pharmaceutical contaminants.

METHODS

An exhaustive collection of bibliographic database was done with articles having high impact and citations in relevant research domains. An in-depth analysis of screened papers was done through standard tools. Studies were categorized according to the use of nanoscale materials as nano-adsorbents (graphene, carbon nanotubes), nanophotocatalysts (metal, metal oxide), nano-filtration, and ozonation for promising alternative technologies for the efficient removal of recalcitrant contaminants.

RESULTS

A total of 365 research articles were selected. The contemporary advancements in the field of nanomaterials for drinking and wastewater treatment have been thoroughly analyzed along with their future perspectives.

CONCLUSION

The recommendations provided in this article will be useful to adopt novel strategies for on-site removal of the emerging contaminants in pharmaceutical effluents and related industries.

Ultra-high adsorption of tetracycline antibiotics on garlic skin-derived porous biomass carbon with high surface area

A porous carbon material with ultra-high specific surface area was prepared from waste garlic skin, and exhibited excellent adsorption properties to TCs in a water environment.

Structural design of magnetic biosorbents for the removal of ciprofloxacin from water

Magnetic biosorbents with specific morphological and molecular structure (PMCCs) were designed for the removal of ciprofloxacin (CIP) from water. Radical polymerization method was applied to immobilize the designed polymer brushes onto core-shell shaped magnetic microspheres to fabricate PMCCs. PMCCs exhibited a maximum adsorption capacity of 527.93 mg·g^-1, which is much higher than reported adsorbents, owing to the complete stretch of polymer brushes and increased active sites as well as enhanced interaction. The investigation on the adsorption behavior of PMCCs for CIP manifested that CIP adsorption well fitted the Langmuir isotherm model and pseudo-second-order kinetic model. The calculated thermodynamic parameters suggested that CIP adsorption onto PMCCs was spontaneous and exothermic. Further recycling experiments showed a loss of less than 20% in the CIP adsorption capacity after five times, demonstrating the reusability of the as-designed biosorbents.