Development of a moving-bed electrochemical membrane bioreactor to enhance removal of low-concentration antibiotic from wastewater

Electro living membrane bioreactor for highly efficient wastewater treatment and fouling mitigation: Influence of current density on process performances

The next generation of the self-forming dynamic membrane, referred to in this study as the "Living Membrane (LM)", is a new patented technology based on an encapsulated biological layer that self-forms on a designed coarse-pore size support material during wastewater treatment and acts as a natural membrane filter. Integrating electrochemical processes with wastewater treatment using the LM approach has also been recently studied (the reactor is referred to as the Electro-Living Membrane Bioreactor or e-LMBR). This study investigated the effects of varying current densities, i.e., 0.3, 0.5, and 0.9 mA/cm2, on the performance of an e-LMBR. The results were also compared with those of the Living Membrane Bioreactor or LMBR (without applied current density). Higher pollutant removals were observed in the presence of the electric field. However, the effect of varying applied current densities on the COD (98-99 %), NH3-N (97-99 %), and PO43-P (100 %) removals was not statistically significant. The more prominent differences (p < 0.05) were observed in the decrease of NO3--N concentrations from mixed liquor to effluent, with increasing current density resulting in lower mean NO3--N effluent concentrations (0.3 mA/cm2: 6.13 mg/L; 0.5 mA/cm2: 4.38 mg/L; 0.9 mA/cm2: 3.70 mg/L). The reduction of NO3--N concentrations as wastewater permeated through the LM layer also confirmed its role in removing nitrogen-containing compounds. Higher current densities resulted in lower concentrations of fouling substances, particularly those of microbial extracellular polymeric substances (EPS) and transparent exopolymer particles (TEPs). The average values of the temporal variation of transmembrane pressure (d(TMP)/d(t)) in the e-LMBR were extremely low, in the range of 0.013-0.041 kPa/day, throughout the operation period. The highest (d(TMP)/d(t)) was observed for the highest current density. However, the TMP values remained below 2 kPa in all the e-LMBR runs even after the initial LM formation stage.

Insight into the mechanism of chlorinated nitroaromatic compounds anaerobic reduction with mackinawite (FeS) nanoparticles

Anaerobic biotechnology for wastewaters treatment can nowadays be considered as state of the art methods. Nonetheless, this technology exhibits certain inherent limitations when employed for industrial wastewater treatment, encompassing elevated substrate consumption, diminished electron transfer efficiency, and compromised system stability. To address the above issues, increasing interest is being given to the potential of using conductive non-biological materials, e,g., iron sulfide (FeS), as a readily accessible electron donor and electron shuttle in the biological decontamination process. In this study, Mackinawite nanoparticles (FeS NPs) were studied for their ability to serve as electron donors for p-chloronitrobenzene (p-CNB) anaerobic reduction within a coupled system. This coupled system achieved an impressive p-CNB removal efficiency of 78.3 ± 2.9% at a FeS NPs dosage of 1 mg/L, surpassing the efficiencies of 62.1 ± 1.5% of abiotic and 30.6 ± 1.6% of biotic control systems, respectively. Notably, the coupled system exhibited exclusive formation of aniline (AN), indicating the partial dechlorination of p-CNB. The improvements observed in the coupled system were attributed to the increased activity in the electron transport system (ETS), which enhanced the sludge conductivity and nitroaromatic reductases activity. The analysis of equivalent electron donors confirmed that the S2- ions dominated the anaerobic reduction of p-CNB in the coupled system. However, the anaerobic reduction of p-CNB would be adversely inhibited when the FeS NPs dosage exceeded 5 g/L. In a continuous operation, the p-CNB concentration and HRT were optimized as 125 mg/L and 40 h, respectively, resulting in an outstanding p-CNB removal efficiency exceeding 94.0% after 160 days. During the anaerobic reduction process, as contributed by the predominant bacterium of Thiobacillus with a 6.6% relative abundance, a mass of p-chloroaniline (p-CAN) and AN were generated. Additionally, Desulfomonile was emerged with abundances ranging from 0.3 to 0.7%, which was also beneficial for the reduction of p-CNB to AN. The long-term stable performance of the coupled system highlighted that anaerobic technology mediated by FeS NPs has a promising potential for the treatment of wastewater containing chlorinated nitroaromatic compounds, especially without the aid of organic co-substrates.

An overview of recent advances and future prospects of three-dimensional biofilm electrode reactors (3D-BERs)

Three-dimensional biofilm electrode reactors (3D-BERs) have attracted extensive attention in recent years due to their wide application range, high efficiency and energy saving. On the basis of traditional bio-electrochemical reactor, 3D-BERs are filled with particle electrodes, also known as the third electrodes, which can not only be used as a carrier for microbial growth, but also improve the electron transfer rate of the whole system. This paper reviews the constitution, advantages and basic principles of 3D-BERs as well as current research status and progress of 3D-BERs in recent years. The selection of electrode materials, including cathode, anode and particle electrode are listed and analyzed. Different constructions of reactors, like 3D-unipolar extended reactor and coupled 3D-BERs are introduced and discussed. Various contaminants degraded by 3D-BERs including nitrogen, azo dyes, antibiotics and the others are calculated and the corresponding degradation effects are described. The influencing factors and mechanisms are also introduced. At the same time, according to the research advances of 3D-BERs, the shortcomings and weakness of this technology in the current research process are analyzed, and the future research direction of this technology is prospected. This review aims to summarize recent studies of 3D-BERs in bio-electrochemical reaction and open a bright window to this booming research theme.

Impact of soil supplemented with pig manure on the abundance of antibiotic resistant bacteria and their associated genes

This study was conducted to evaluate the abundance of antibiotic resistant bacteria and their resistance genes from agriculture soil supplemented with pig manure. Uncultivable soil sample was supplemented with pig manure samples under microcosm experimental conditions and plated on Luria-Bertani (LB) agar incorporated with commercial antibiotics. The supplementation of soil with 15% pig manure resulted in the highest increase in the population of antibiotic resistant bacteria (ARB)/multiple antibiotic resistant bacteria (MARB). Seven genera that included Pseudomonas, Escherichia, Providencia, Salmonella, Bacillus, Alcaligenes and Paenalcaligenes were the cultivable ARB identified. A total of ten antibiotic resistant bacteria genes (ARGs) frequently used in clinical or veterinary settings and two mobile genetic elements (MGEs) (Class 1 and Class 2 integrons) were detected. Eight heavy metal, copper, cadmium, chromium, manganese, lead, zinc, iron, and cobalt were found in all of the manure samples at different concentrations. Tetracycline resistance genes were widely distributed with prevalence of 50%, while aminoglycoside and quinolone-resistance gene had 16% and 13%, respectively. Eighteen ARB isolates carried more than two ARGs in their genome. Class 1 integron was detected among all the 18 ARB with prevalence of 90-100%, while Class 2 integron was detected among 11 ARB. The two classes of integron were found among 10 ARB. Undoubtedly, pig manure collected from farms in Akure metropolis are rich in ARB and their abundance might play a vital role in the dissemination of resistance genes among clinically-relevant pathogens.

Research progress of electrically-enhanced membrane bioreactor (EMBR) in pollutants removal and membrane fouling alleviation

Membrane bioreactor (MBR), as a biological unit for wastewater treatment, has been proven to have the advantages of simple structure and high pollutant removal rate. However, membrane fouling limits its wide application, and it is crucial to adopt effective membrane fouling control methods. As a new type of membrane fouling control technology, electrically-enhanced MBR (EMBR) has attracted more interest recently. It uses the driving force of electric field to make pollutants flocculate or move away from the membrane surface to achieve the purpose of inhibiting membrane fouling. This paper expounds the configuration of EMBR in recent years, including the location of membrane components, the way of electric field application and the selection of electrode and membrane materials, and provides the latest development information in various aspects. The enhanced effect of electric field on the removal of comprehensive and refractory pollutants is outlined in detail. And from the perspective of sludge properties (EPS, SMP, sludge particle size, zeta potential and microbial activity), the influence of electric field on sludge characteristics and the relationship between the changes of sludge properties in EMBR and membrane fouling are discussed. Moreover, the electrochemical mechanisms of electric field alleviating membrane fouling are elucidated from electrophoresis, electrostatic repulsion, electroflocculation, electroosmosis, and electrochemical oxidation, and the regeneration and stability of EMBR are assessed. The existing challenges and future research directions are also proposed. This review could provide theoretical guidance and further studies for subsequent topic, and promoting the wide engineering applications of EMBR.

Recent perspective of antibiotics remediation: A review of the principles, mechanisms, and chemistry controlling remediation from aqueous media

Antibiotic pollution is an ever-growing concern that affects the growth of plants and the well-being of animals and humans. Research on antibiotics remediation from aqueous media has grown over the years and previous reviews have highlighted recent advances in antibiotics remediation technologies, perspectives on antibiotics ecotoxicity, and the development of antibiotic-resistant genes. Nevertheless, the relationship between antibiotics solution chemistry, remediation technology, and the interactions between antibiotics and adsorbents at the molecular level is still elusive. Thus, this review summarizes recent literature on antibiotics remediation from aqueous media and the adsorption perspective. The review discusses the principles, mechanisms, and solution chemistry of antibiotics and how they affect remediation and the type of adsorbents used for antibiotic adsorption processes. The literature analysis revealed that: (i) Although antibiotics extraction and detection techniques have evolved from single-substrate-oriented to multi-substrates-oriented detection technologies, antibiotics pollution remains a great danger to the environment due to its trace level; (ii) Some of the most effective antibiotic remediation technologies are still at the laboratory scale. Thus, upscaling these technologies to field level will require funding, which brings in more constraints and doubts patterning to whether the technology will achieve the same performance as in the laboratory; and (iii) Adsorption technologies remain the most affordable for antibiotic remediation. However, the recent trends show more focus on developing high-end adsorbents which are expensive and sometimes less efficient compared to existing adsorbents. Thus, more research needs to focus on developing cheaper and less complex adsorbents from readily available raw materials. This review will be beneficial to stakeholders, researchers, and public health professionals for the efficient management of antibiotics for a refined decision.

Efficient mitigation of emerging antibiotics residues from water matrix: Integrated approaches and sustainable technologies

The prevalence of antibiotic traces in the aquatic matrices is a concern due to the emanation of antibiotic resistance which requires a multifaceted approach. One of the potential sources is the wastewater treatment plants with a lack of advance infrastructure leading to the dissemination of contaminants. Continuous advancements in economic globalization have facilitated the application of several conventional, advanced, and hybrid techniques for the mitigation of rising antibiotic traces in the aquatic matrices that have been thoroughly scrutinized in the current paper. Although the implementation of existing mitigation techniques is associated with several limiting factors and barriers which require further research to enhance their removal efficiency. The review further summarizes the application of the microbial processes to combat antibiotic persistence in wastewater establishing a sustainable approach. However, hybrid technologies are considered as most efficient and environmental-benign due to their higher removal efficacy, energy-efficiency, and cost-effectiveness. A brief elucidation has been provided for the mechanism responsible for lowering antibiotic concentration in wastewater through biodegradation and biotransformation. Overall, the current review presents a comprehensive approach for antibiotic mitigation using existing methods however, policies and measures should be implemented for continuous monitoring and surveillance of antibiotic persistence in aquatic matrices to reduce their potential risk to humans and the environment.

A review on three-dimensional electrochemical technology for the antibiotic wastewater treatment

The potential genotoxicity and non-biodegradability of antibiotics in the natural water bodies threaten the survival of various living things and cause serious environmental pollution and destruction. Three-dimensional (3D) electrochemical technology is considered a powerful means for antibiotic wastewater treatment as it can degrade non-biodegradable organic substances into non-toxic or harmless substances and even completely mineralize them under the action of electric current. Therefore, antibiotic wastewater treatment using 3D electrochemical technology has now become a hot research topic. Thus, in this review, a detailed and comprehensive investigation was conducted on the antibiotic wastewater treatment using 3D electrochemical technology, including the structure of the reactor, electrode materials, the influence of operating parameters, reaction mechanism, and combination with other technologies. Many studies have shown that the materials of electrode, especially particle electrode, have a great effect on the antibiotic wastewater treatment efficiency. The influence of operating parameters such as cell voltage, solution pH, and electrolyte concentration was very significant. Combination with other technologies such as membrane and biological technologies has effectively increased antibiotic removal and mineralization efficiency. In conclusion, the 3D electrochemical technology is considered as a promising technology for the antibiotic wastewater treatment. Finally, the possible research directions of the 3D electrochemical technology for antibiotic wastewater treatment were proposed.

Role of bio-electrochemical technology for enzyme activity stimulation in high-consumption pharmaceuticals biodegradation

Active pharmaceutical ingredients (APIs) and their intermediate residues have recently been considered a serious concern. Among technologies, bio-electrochemical technologies (BETs) have stimulated the production of bio-electrical energy. This review aims to examine the benefit and mechanism of BETs on the degradation of high-consumption pharmaceutical compounds, including antibiotic, anti-inflammatory, and analgesic drugs, and the stimulation of enzymes induced in a bioreactor. Moreover, intermediates and the proposed pathways of pharmaceutical compound biodegradation in BETs are to be explained in this review. According to studies performed exclusively, the benefit of BETs is using bio-electroactive microbes to mineralize recalcitrant pharmaceutical contaminants by promoting enzyme activity and energy. Since BETs use the electron transfer chain between bio-anode/-cathode and pharmaceuticals, the enzyme activity is essential in the oxidation and reduction of phenolic rings of drugs and the ineffective detoxification of effluent from the treatment plant. This study is suggested a vital and influential role of BETs in mineralizing and enzyme induction in bioreactors. Eventually, a content of future developments or outlooks of BETs are propounded to improve the pharmaceutical industries' wastewater problems.

Toward emerging contaminants removal using acclimated activated sludge in the gravity-driven membrane filtration system

The occurrence of emerging contaminants is attracting widespread attention due to its potential threat to aquatic organisms and public health. Gravity-driven membrane (GDM) filtration can effectively eliminate water contamination with pathogenic microorganisms in rural areas while being challenged by various micro-pollutants (MPs). This study investigated the removal and transformation of sulfamethoxazole (SMX) in GDM for the first time, and pre-adding acclimated activated sludge was proposed to improve the removal of MPs. More rapid and higher SMX degradation was observed with pre-adding domestication sludge, and the system had better tolerance to SMX shocks. Besides, in the presence of domesticated sludge, more SMX metabolic pathways and better mineralization rates were obtained, which was related to more SMX-resistant bacteria and easier biodegradable carbon sources in the system. Pre-adding sludge also increased the richness and diversity of bacterial community, which provided higher removal efficiencies of conventional pollutants. Thus, the removal rates of DOC (14.7%), NH₄⁺-N (5.6%) and fluorescent substances were obviously improved compared with the control group. In this study, the crisis of MPs was tackled and the removal of conventional pollutants was enhanced by pre-adding domesticated sludge in GDM, which ensured the water quality in rural areas.

Efficiency of various biofilm carriers and microbial interactions with substrate in moving bed-biofilm reactor for environmental wastewater treatment

In a moving bed-biofilm reactor (MBBR), the fluidization efficiency, immobilization of microbial cells, and treatment efficiency are directly influenced by the shape and pores of biofilm carriers. Moreover, the efficacy of bioremediation mainly depends on their interaction interface with microbes and substrate. This review aims to comprehend the role of different carrier properties such as material shapes, pores, and surface area on bioremediation productivity. A porous biofilm carrier with surface ridges containing spherical pores sizes > 1 mm can be ideal for maximum efficacy. It provides diverse environments for cell cultures, develops uneven biofilms, and retains various cell sizes and biomass. Moreover, the thickness of biofilm and controlled scaling shows a significant impact on MBBR performance. Therefore, the effect of these parameters in MBBR is discussed detailed in this review, through which existing literature and technical strategies that focus on the surface area as the primary factor can be critically assessed.

A critical review on classifications, characteristics, and applications of electrically conductive membranes for toxic pollutant removal from water: Comparison between composite and inorganic electrically conductive membranes

Research efforts have recently been directed at developing electrically conductive membranes (EMs) for pressure-driven membrane separation processes to remove effectively the highly toxic pollutants from water. EMs serve as both the filter and the electrode during filtration. With the assistance of a power supply, EMs can considerably improve the toxic pollutant removal efficiency and even realize chemical degradation to reduce their toxicity. Organic-inorganic composite EMs and inorganic EMs show remarkable differences in characteristics, removal mechanisms, and application situations. Understanding their differences is highly important to guide the future design of EMs for specific pollutant removal from water. However, reviews concerning the differences between composite and inorganic EMs are still lacking. In this review, we summarize the classifications, fabrication techniques, and characteristics of composite and inorganic EMs. We also elaborate on the removal mechanisms and performances of EMs toward recalcitrant organic pollutants and toxic inorganic ions in water. The comparison between composite and inorganic EMs is emphasized particularly in terms of the membrane characteristics (pore size, permeability, and electrical conductivity), application situations, and underlying removal mechanisms. Finally, the energy consumption and durability of EMs are evaluated, and future perspectives are presented.

Anaerobic electrochemical membrane bioreactor effectively mitigates antibiotic resistance genes proliferation under high antibiotic selection pressure

The spread of antibiotics and antibiotic resistance genes (ARGs) in environments has posed potential threats to public health. Unfortunately, conventional biological wastewater treatment technologies generally show insufficient removal of antibiotics and ARGs. Bioelectrochemical systems, which can effectively degrade refractory organic pollutants via enhancing microbial metabolisms through electrochemical redox reaction, may provide an alternative for the control of antibiotics and ARGs. Herein, an anaerobic electrochemical membrane bioreactor (AnEMBR) was conducted by combining bioelectrochemical system and anaerobic membrane bioreactor to treat antibiotic-containing wastewater. The AnEMBR at open circuit showed stable CH4 production and high removal of COD and chlortetracycline (CTC) in treating 2.5-15 mg/L CTC. However, increasing CTC to 45 mg/L completely inhibited the methanogenesis of AnEMBR at open circuit. After applying external voltage in AnEMBR, the performances of AnEMBR were significantly improved (e.g., increased CH4 production and CTC removal). Moreover, CTC exposure significantly increased the relative abundances of ARGs in sludge, supernatant, and effluent in AnEMBR at open circuit. Applying voltage greatly attenuated the total relative abundances of ARGs in the supernatant and effluent of AnEMBR compared to those at open circuit. This could be attributed to the enrichment of tetracycline degradation gene tetX, which greatly enhanced the removal of CTC by the AnEMBR and thus reduced the selective pressure of CTC on the microorganisms in supernatant and effluent for ARGs proliferation. These results would provide an effective wastewater treatment technology for treating high-level antibiotic-containing wastewater to mitigate the potential risk of ARGs and antibiotics spread in receiving water body.

Biofouling suppresses effluent toxicity in an electrochemical filtration system for remediation of sulfanilic acid-contaminated water

Electrochemical filtration system (EFS) has received broad interest due to its high efficiency for organic contaminants removal. However, the porous nature of electrodes and flow-through operation mode make it susceptible to potential fouling. In this work, we systematically investigated the impacts of biofouling on sulfanilic acid (SA) removal and effluent toxicity in an EFS. Results showed that the degradation efficiency of SA slightly deteriorated from 92.3% to 81.1% at 4.0 V due to the electrode fouling. Surprisingly, after the occurrence of fouling, the toxicity (in terms of luminescent bacteria inhibition) of the EFS effluent decreased from 72.3% to 40.2%, and cytotoxicity assay exhibited similar tendency. Scanning electron microscopy and confocal laser scanning microscopy analyses revealed that biofouling occurred on the porous cathode, and live microorganisms were the dominant contributors, which are expected to play an important role in toxicity suppression. The relative abundance of Flavobacterium genus, related to the degradation of p-nitrophenol (an aromatic intermediate product of SA), increased on the membrane cathode after fouling. The analysis of degradation pathway confirmed the synergetic effects of electrochemical oxidation and biodegradation in removal of SA and its intermediate products in a bio-fouled EFS, accounting for the decrease of the effluent toxicity. Results of our study, for the first time, highlight the critical role of biofouling in detoxication using EFS for the treatment of contaminated water.

An efficient simultaneous degradation of sulfamethoxazole and trimethoprim by photoelectro-Fenton process under non-modified pH using a natural citric acid source: study of biodegradability, ecotoxicity, and antibacterial activity

In this work, the use of natural organic wastes (orange and lemon peels) as sources of citric acid was evaluated along with the application of the photoelectro-Fenton (PEF) system under non-modified pH as a novel alternative to degrade a complex mixture of pharmaceuticals: sulfamethoxazole (SMX-7.90 × 10^-5 mol/L) and trimethoprim (TMP-6.89 × 10^-5 mol/L). The system was equipped with a carbon felt air diffusion cathode (GDE) and a Ti/IrO₂ anode doped with SnO₂ (DSA). A 3.6 × 10^-5 mol/L solution of commercial citric acid was used as a reference. The pharmaceuticals' evolution in the mixture was followed by high-performance liquid chromatography (HPLC). The addition of natural products showed an efficient simultaneous degradation of the antibiotics (100% of SMX and TMP at 45 min and 90 min, respectively) similar to the performance produced by adding the commercial citric acid to the PEF system. Moreover, the addition of natural products allowed for an increment of biodegradability (100% removal of TOC by a modified Zahn Wellens test) and a decrease in ecotoxicity (0% in the bioassay with D. Magna) of the treated solutions. The antibacterial activity was eliminated after only 45 min of treatment, suggesting that the degradation by-products do not represent a significant risk to human health or the environment in general. Results suggest that, because of the efficient formation of Fe-citrate complexes, the PEF could be enhanced by the addition of natural organic wastes as a sustainable alternative ecological system for water contaminated pharmaceuticals. Additionally, the potential of reusing natural organic wastes has been exposed, contributing to an improved low-cost PEF by decreasing the environmental contamination produced by this type of waste.

Recent advances in electrocatalytic membrane for the removal of micropollutants from water and wastewater

The increasing occurrence of micropollutants in water and wastewater threatens human health and ecological security. Electrocatalytic membrane (EM), a new hybrid water treatment platform that integrates membrane separation with electrochemical technologies, has attracted extensive attention in the removal of micropollutants from water and wastewater in the past decade. Here, we systematically review the recent advances of EM for micropollutant removal from water and wastewater. The mechanisms of the EM for micropollutant removal are first introduced. Afterwards, the related membrane materials and operating conditions of the EM are summarized and analyzed. Lastly, the challenges and future prospects of the EM in research and applications are also discussed, aiming at a more efficient removal of micropollutants from water and wastewater.

HKUST-1 derived carbon adsorbents for tetracycline removal with excellent adsorption performance

As the abuse of antibiotics has led to increasingly serious environmental pollution problems, studies have found that the adsorption method can be used to efficiently and quickly remove residual antibiotics in water with low cost and high efficiency. Metal-organic frameworks and their derived porous carbons have received widespread attention as a new type of adsorption material. In this study, HKUST-1 was synthesized by a hydrothermal method and carbonized to HDC-350 at 350 °C under an oxygen-free atmosphere. Through adsorption experiments, HDC-350 is found to show a superior adsorption effect for tetracycline (TC), with an adsorption capacity that reaches 136.88 mg g^-1. The TC adsorption mechanism was studied through characterization and analysis of HDC-350. The adsorption of TC by HDC-350 mainly relies on electrostatic attraction, hydrogen bonding, metal-organic complexation, and intermolecular interactions. This study shows that HKUST-1-derived porous carbon can be used to improve the water stability of HKUST-1, and, at the same time, can effectively adsorb TC in solution, which provides good conditions for practical research applications in the future.

Performance and recovery of nitrifying biofilm after exposure to prolonged starvation

Achieving consistent ammonia removal in post-lagoon processes faces two major challenges impacting nitrifiers due to the unique seasonal variation of lagoon-based systems: summer to winter temperature drop and summer to fall ammonia starvation period while lagoon is removing ammonia. The objective of this study was to follow microbial diversity and define conditions that could overcome these challenges in a post-lagoon moving bed biofilm reactor (MBBR) operated at an initial surface area loading rate (SALR) of 0.3 g-NH4-N m^-2d^-1 from mesophilic (20 °C) to psychrophilic (4 °C). Initially the temperature was maintained at 20 °C and decreased to 10 °C until steady state was achieved. During starvation conditions (i.e., continuous, intermittent and no aeration without inflow; decanted media; and intermittent and continuous ammonia supplement) the temperature was decreased by 2 °C per week until 4 °C. The results indicated that operational procedures, such as intermittent ammonia supplement with SALR of 0.15 g-NH₄-N m^-2d^-1 could improve performance with 80% ammonia removal achieved immediately after starvation period. Intermittent ammonia supplement had produced the greatest biofilm preservation comparable to the initial load with the highest specific and surface area removal rates. In the recovery phase (initial load restoration) 10 days were required to reestablish performance above 95% ammonia removal. When temperature was decreased from mesophilic to psychrophilic, the microbial diversity was found higher when starving biofilm compared to the control operated at the initial load while it converged to a similar population over recovery. The main actors associated to nitrification enriched at psychrophilic conditions were Proteobacteria and Bacteriodotes at phyla level. Ammonia oxidation to nitrite was mainly driven by the order Burkholderiales and nitrite oxidation to nitrate by Pseudomonadales. This procedure should be considered in the implementation of full-scale post-lagoon MBBR technologies to ensure reliable, robust, and consistent performance despite the inherent seasonal variability of lagoon-based processes.

Three-dimensional biofilm electrode reactors (3D-BERs) for wastewater treatment

Three-dimensional biofilm electrode reactors (3D-BERs) are highly efficient in refractory wastewater treatment. In comparison to conventional bio-electrochemical systems, the filled particle electrodes act as both electrodes and microbial carriers in 3D-BERs. This article reviews the conception and basic mechanisms of 3D-BERs, as well as their current development. The advantages of 3D-BERs are illustrated with an emphasis on the synergy of electricity and microorganisms. Electrode materials utilized in 3D-BERs are systematically summarized, especially the critical particle electrodes. The configurations of 3D-BERs and their integration with wastewater treatment reactors are introduced. Operational parameters and the adaptation of 3D-BERs to varieties of wastewater are discussed. The prospects and challenges of 3D-BERs for wastewater treatment are then presented, and the future research directions are proposed. We believe that this timely review will help to attract more attentions on 3D-BERs investigation, thus promoting the potential application of 3D-BERs in wastewater treatment.

Recent advances in membrane biofilm reactor for micropollutants removal: Fundamentals, performance and microbial communities

The occurrence of micropollutants (MPs) in water and wastewater imposes potential risks on ecological security and human health. Membrane biofilm reactor (MBfR), as an emerging technology, has attracted much attention for MPs removal from water and wastewater. The review aims to consolidate the recent advances in membrane biofilm reactor for MPs removal from the standpoint of fundamentals, removal performance and microbial communities. First, the configuration and working principles of MBfRs are reviewed prior to the discussion of the current status of the system. Thereafter, a comprehensive review of the MBfR performance for MPs elimination based on literature database is presented. Key information on the microbial communities that are of great significance for the removal performance is then synthesized. Perspectives on the future research needs are also provided in this review to ensure the development of MBfRs for more cost-effective elimination of MPs from water and wastewater.

Bifunctional two-dimensional copper-aluminum modified filter paper composite for efficient tetracycline removal: Synergy of adsorption and reusability by degradation

Herein, bifunctional two-dimensional copper-aluminum modified filter paper composite (2D-Cu/Al-C) was successfully prepared by simple calcination and showed ultrahigh adsorption performance and degradation potential. The adsorption removal of TC on 2D-Cu/Al-C all exceeded 92.2% under solution conditions of 10-200 mg/L TC, 100 mg/L 2D-Cu/Al-C, pH 8 and 298 K. The pseudo-second-order kinetic and Langmuir models better fitted the kinetic and isotherm data via spontaneous and exothermic process, and the maximum capacity of the 2D-Cu/Al-C was 2391.78 mg/g. Additionally, 2D-Cu/Al-C showed desired specific adsorption for TC (TC: 98.7%, norfloxacin: 5.8%, sulfamethoxazole: 2.1%, and ciprofloxacin: 1.8%) and it could effectively adsorbed TC even in the binary system (various coexisting ions or natural organic matter). After TC adsorbed on adsorbent was mineralized into CO₂ and H₂O by adding peroxydisulfate to generate high electrode potential radical in another limited systems, the 2D-Cu/Al-C still had ∼89.12% on TC removal (initial concentration of 50 mg/L) after five experimental cycles. Zeta potential, FT-IR and XPS results indicated that the multi-adsorption mechanism, including electrostatic interactions, complexation, and H-bonds, played a vital role in the fast and efficient adsorption process. Thus, the way of combining adsorption and regeneration via degradation are green, non-polluting strategy which are expected to be applied for water purification in future environmental remediation.

Efficacy of a novel electrochemical membrane-aerated biofilm reactor for removal of antibiotics from micro-polluted surface water and suppression of antibiotic resistance genes

An electrochemical membrane-aerated biofilm reactor (EMABR) was developed for removing sulfamethoxazole (SMX) and trimethoprim (TMP) from contaminated water. The exertion of electric field greatly enhanced the degradation of SMX and TMP in the EMABR (~60%) compared to membrane-aerated biofilm reactor (MABR, < 10%), due to the synergistic effects of the electro-oxidation (the generation of reactive oxygen species) and biological degradation. Microbial community analyses demonstrated that the EMABR enriched the genus of Xanthobacter, which was potentially capable of degrading aromatic intermediates. Moreover, the EMABR had a lower relative abundance of antibiotic resistance genes (ARGs) (0.23) compared to the MABR (0.56), suggesting the suppression of ARGs in the EMABR. Further, the SMX and TMP degradation pathways were proposed based on the detection of key intermediate products. This study demonstrated the potential of EMABR as an effective technology for removing antibiotics from micro-polluted surface water and suppressing the development of ARGs.

Efficient degradation of tetracycline by RGO@black titanium dioxide nanofluid via enhanced catalysis and photothermal conversion

The applications of photocatalytic pollutant degradation have remained limited due to the low efficiency of solar energy utilization. In this study, a photothermal catalyst consisting of reduced graphene oxide @ black TiO₂ (RGO@BT) nanofluid with effective full-spectrum (from ultraviolet to infrared light) absorption was synthesized by a typical two-step method of high temperature calcination and hydrothermal method. Moreover, the photothermal catalytic performance of the RGO@BT nanofluid on tetracycline was verified. Compared with individual processes (i.e, photocatalysis and thermocatalysis), the photothermal catalytic process significantly enhanced tetracycline degradation under simulated global standard spectrum sunlight (AM 1.5G, 1000 W m^-2). The maximum photothermal conversion efficiency reached 91.8%, which resulted in 94.7% tetracycline degradation (40 mg L^-1) after 120 min of treatment with 200 mg L^-1 RGO@BT nanofluid. Holes, OH, and O₂^- were found to be the main active species during the photothermal catalytic process. Moreover, heat was spontaneously converted from light energy without the use of any external energy source. The elevated system temperature facilitated the tetracycline degradation based on the Arrhenius behavior. These findings provide insights into the improvement of photocatalytic efficiency in organic contaminant degradation via solar energy-efficient photothermal conversion materials.

Wastewater treatment and fouling control in an electro algae-activated sludge membrane bioreactor

The effect of addition of algae to activated sludge as active biomass in membrane bioreactors (MBRs) and electro-MBRs (e-MBRs) for wastewater remediation was examined in this study. The performances of Algae-Activated Sludge Membrane Bioreactor (AAS-MBR) and electro Algae-Activated Sludge Membrane Bioreactor (e-AAS-MBR) were compared to those observed in conventional MBR and e-MBR, which were previously reported and utilized activated sludge as biomass. The effect of application of electric field was also examined by the comparison of performances of e-AAS-MBR and AAS-MBR. Similar chemical oxygen demand (COD) reduction efficiencies of AAS-MBR, e-AAS-MBR, MBR, and e-MBR (98.35 ± 0.35%, 99.12 ± 0.08%, 97.70 ± 1.10%, and 98.10 ± 1.70%, respectively) were observed. The effect of the algae-activated sludge system was significantly higher in the nutrient removals. Ammoniacal nitrogen (NH₃-N) removal efficiencies of AAS-MBR and e-AAS-MBR were higher by 43.89% and 26.61% than in the conventional MBR and e-MBR, respectively. Phosphate phosphorous (PO₄^3--P) removals were also higher in AAS-MBR and e-AAS-MBR by 6.43% and 2.66% than those in conventional MBR and e-MBR. Membrane fouling rates in AAS-MBR and e-AAS-MBR were lower by 57.30% and 61.95% than in MBR and e-MBR, respectively. Lower concentrations of fouling substances were also observed in the reactors containing algae-activated sludge biomass. Results revealed that addition of algae improved nutrient removal and membrane fouling mitigation. The study also highlighted that the application of electric field in the e-AAS-MBR enhanced organic contaminants and nutrients removal, and fouling rate reduction.

Effects of coarse and fine bubble aeration on performances of membrane filtration and denitrification in moving bed membrane bioreactors

In this study, two lab-scale Moving Bed Membrane Bioreactors (MBMBR) were setup and operated in parallel to study the effect of coarse and fine bubble aeration on the performances of membrane filtration and denitrification treating domestic wastewater. The bacterial populations in the two MBMBRs were further analyzed to investigate the mechanisms involved in the different denitrification performances. The results showed that coarse bubble aeration could effectively mitigate membrane fouling by decreasing the formation of cake layer, although smaller sizes of bio-flocs were induced. In addition, coarse bubble aeration could also maintain dissolved oxygen (DO) at a relatively lower level without compromising the moving of bio-carriers, which achieved 10% higher total nitrogen removal rate due to anoxic zone created at inner layers of biofilms on bio-carriers. Accumulation of denitrifier (Thiobacillus denitrificans) on the bio-carriers was found under the coarse bubble aeration system, which can explain its superior denitrification performance.

Efficacy of electrochemical membrane bioreactor for virus removal from wastewater: Performance and mechanisms

Wastewater treatment facilities play pivotal roles in preventing the transmission of water-borne viruses and protecting human health. In this study, a new electrochemical membrane bioreactor (EMBR) was proposed to achieve a long-lasting and efficient removal of virus from wastewater. Results showed that applying a low electric field (2.0 V) in EMBR system could achieve ~100% removal efficiency at both batch tests and continuous flow experiments. In contrast, the control MBR, without the exertion of electric field, exhibited a very low removal efficiency (19.8% on average). Moreover, the fouling in EMBR was significantly mitigated, which enabled its operation duration almost 3 times longer than that of the control. Further explorations suggested that the reactive oxidants generated on electrodes in the EMBR system were mainly responsible for MS2 removal. This study demonstrated the potential of utilizing the EMBR process to achieve an enhanced virus disinfection efficiency during the wastewater treatment process.

Self-propagating synthesis of Zn-loaded biochar for tetracycline elimination

Herein, a novel Zn-loaded biochar (Zn-LBC) originating from Fraxinus pennsylvanica Marsh leaves was successfully prepared through a simple and rapid self-propagating combustion reaction (SHS) and could serve as an efficient adsorbent for tetracycline (TC) elimination from water. The adsorption performance was analyzed via a series of characterizations and batch adsorption experiments. The results showed that the novel adsorbent Zn-LBC exhibited an excellent TC adsorption capacity (159.64 mg/g), which was 2.63 times higher than that of the original biochar (60.78 mg/g). The pseudo-second-order kinetic model and Freundlich isothermal model fit the adsorption data well. It is noteworthy that Zn-LBC had little effect on the adsorption capacity of TC in the 0-10 mg/L various coexisting ion range and presence of humic acid (HA). In addition, the adsorption test of TC using hospital wastewater as the water sample also achieved satisfactory results (raw influent: 52.65 mg/g, final effluent: 85.64 mg/g). FT-IR and XPS investigations showed that the TC adsorption mechanism included surface complexation, π-π interactions, and hydrogen bonds. The results provide new ideas for exploring low-cost and highly efficient modified biochar adsorbent for TC elimination.

An electrochemical membrane biofilm reactor for removing sulfonamides from wastewater and suppressing antibiotic resistance development: Performance and mechanisms

Sulfonamides, such as sulfadiazine (SDZ), are frequently detected in water and wastewater with their toxic and persistent nature arousing much concern. In this work, a novel electrochemical membrane biofilm reactor (EMBfR) was constructed for the removal of SDZ whilst suppressing the development of antibiotic resistance genes (ARGs). Results showed that the EMBfR achieved 94.9% removal of SDZ, significantly higher than that of a control membrane biofilm reactor (MBfR) without electric field applied (44.3%) or an electrolytic reactor without biofilm (77.3%). Moreover, the relative abundance of ARGs in the EMBfR was only 32.0% of that in MBfR, suggesting that the production of ARGs was significantly suppressed in the EMBfR. The underlying mechanisms relate to (i) the change of the microbial community structure in the presence of the electric field, leading to the enrichment of potential aromatic-degrading microorganisms (e.g., Rhodococcus accounting for 51.0% of the total in the EMBfR compared to 10.0% in the MBfR) and (ii) the unique degradation pathway of SDZ in the EMBfR attributed to the synergistic effect between the electrochemical and biological processes. Our study highlights the benefits of EMBfR in removing pharmaceuticals from contaminated waters and suppressing the development (and transfer) of ARGs in the environment.

Electrochemical biofilm control by reconstructing microbial community in agricultural water distribution systems

Biofilm causes considerable technical challenges in agricultural water distribution systems. Electrochemical treatment (ECT) is a potential technique for controlling biofilm in the systems. Given the limited information on how ECT performance changes of irrigation systems and microbial biofilm community shifts. In this study, the effect of anti-biofilm was assessed. Illumina Miseq high-throughput sequencing, combined with molecular ecological network analysis, were applied to detect the effects of ECT on attached biofilm microbial communities. We found that ECT effectively mitigated biofilm formation with the fixed-biofilm biomass reduced by 37.5 %-79.9 %. ECT significantly shifted the bacterial community structures in the biofilm, reduced the communities' diversity, and changed the dominant species. Molecular ecological network analysis showed that the complexity and size of bacterial networks were destabilized under ECT and decreased the interactions among bacterial species. The reconstruction in bacterial community and networks were responsible for the decline in extracellular polymer substances and biofilm biomass. However, chlorine-resistant bacteria were found increased after ECT, and higher relative abundance and low biofilm removal was identified in continuous ECT as compared with intermittent ECT. These results aimed to highlight the opportunity for biofouling mitigation by ECT for irrigation systems, and reveal the potential anti-biofilm microbial mechanisms of ECT.

Self-Enhanced Decomplexation of Cu-Organic Complexes and Cu Recovery from Wastewaters Using an Electrochemical Membrane Filtration System

Heavy metals in industrial wastewaters are typically present as stable metal-organic complexes with their cost-effective treatment remaining a significant challenge. Herein, a self-enhanced decomplexation scenario is developed using an electrochemical membrane filtration (EMF) system for efficient decomplexation and Cu recovery. Using Cu-EDTA as a model pollutant, the EMF system achieved 81.5% decomplexation of the Cu-EDTA complex and 72.4% recovery of Cu at a cell voltage of 3 V. The ^•OH produced at the anode first attacked Cu-EDTA to produce intermediate Cu-organic complexes that reacted catalytically with the H₂O₂ generated from the reduction of dissolved oxygen at the cathode to initiate chainlike self-enhanced decomplexation in the EMF system. The decomplexed Cu products were further reduced or precipitated at the cathodic membrane surface thereby achieving efficient Cu recovery. By scavenging H₂O₂ (excluding self-enhanced decomplexation), the rate of decomplexation decreased from 8.8 × 10^-1 to 4.1 × 10^-1 h^-1, confirming the important role of self-enhanced decomplexation in this system. The energy efficiency of this system is 93.5 g kWh^-1 for Cu-EDTA decomplexation and 15.0 g kWh^-1 for Cu recovery, which is much higher than that reported in the previous literature (i.e., 7.5 g kWh^-1 for decomplexation and 1.2 g kWh^-1 for recovery). Our results highlight the potential of using EMF for the cost-effective treatment of industrial wastewaters containing heavy metals.

Membrane Separation Coupled with Electrochemical Advanced Oxidation Processes for Organic Wastewater Treatment: A Short Review

Research on the coupling of membrane separation (MS) and electrochemical advanced oxidation processes (EAOPs) has been a hot area in water pollution control for decades. This coupling aims to greatly improve water quality and focuses on the challenges in practical application to provide a promising solution to water shortage problems. This article provides a summary of the coupling configurations of MS and EAOPs, including two-stage and one-pot processes. The two-stage process is a combination of MS and EAOPs where one process acts as a pretreatment for the other. Membrane fouling is reduced when setting EAOPs before MS, while mass transfer is promoted when placing EAOPs after MS. A one-pot process is a kind of integration of two technologies. The anode or cathode of the EAOPs is fabricated from porous materials to function as a membrane electrode; thus, pollutants are concurrently separated and degraded. The advantages of enhanced mass transfer and the enlarged electroactive area suggest that this process has excellent performance at a low current input, leading to much lower energy consumption. The reported conclusions illustrate that the coupling of MS and EAOPs is highly applicable and may be widely employed in wastewater treatment in the future.

Electrochemical membrane bioreactors: State-of-the-art and future prospects

Integration of an electrochemical process with membrane bioreactor (MBR) has attracted considerable attention in the last decade for simultaneous improvement in pollutant removal and hydraulic performance of MBR. Electrochemical MBR (eMBR) with sacrificial anodes has been observed to achieve enhanced phosphorus (up to 40%) and micropollutant removal (5-60%). This is because direct anodic oxidation, indirect oxidation by reactive oxygen species and electrocoagulation can supplement the biological process. The application of an electric field can substantially reduce membrane fouling by 10% to 95% in the eMBR as compared to the conventional MBR. Sacrificial electrodes (e.g., iron or aluminium) have been reported to be more suitable for fouling mitigation than non-sacrificial electrodes (e.g., titanium). However, during prolonged operation, metal ions released from sacrificial electrodes can adversely affect microbial activity and could accumulate in activated sludge. Depending on the current density and electrode material (sacrificial or non- sacrificial), anodic oxidation, electrocoagulation, electrophoresis and/or electroosmosis mechanisms are responsible for suppressing membrane fouling propensity. This paper critically reviews the current status of the electrochemical MBR technology and presents a concise summary of eMBR configurations and electrode materials. Comparative removal of bulk organics, nutrients and micropollutants in the eMBR and conventional MBR is discussed, and performance governing factors are elucidated. Impacts of operating conditions such as current density on mixed liquor properties (e.g., floc size and zeta potential) and microbial activity are elucidated. The extent of membrane fouling mitigation along with associated mechanisms as well as energy consumption is explained and critically analysed. Future research directions are suggested to fast track the scalability of eMBR, which include but are not limited to electrode lifetime, development of self-cleaning conductive membranes, optimisation of operating parameters, removal of emerging micropollutants, accumulation of toxic metals in activated sludge, and degradation by-products and ecotoxicity.

Enhanced removal of pharmaceuticals and personal care products from real municipal wastewater using an electrochemical membrane bioreactor

A novel electrochemical membrane bioreactor (EMBR) was developed for enhancing PPCPs removal from real municipal wastewater. Compared to the control MBR (CMBR) without applying electric field, EMBR exhibited higher removal efficiencies for 14 PPCPs among all investigated PPCPs, including 3 fluoroquinolones, 2 macrolides, 6 sulfonamides and 3 anti-inflammatory drugs, while no significant difference was observed for the rest 8 PPCPs. The enhanced removal of 14 PPCPs was mainly attributed to electrooxidation by the direct anodic oxidation and reactive oxygen species-mediated indirect oxidation. Moreover, membrane fouling rates of EMBR (0.55 ± 0.10 kPa/d) were significantly reduced compared with CMBR (0.99 ± 0.09 kPa/d). Microbial activities and community analyses demonstrated that the applied electric field had no noticeable adverse impact on microbial viabilities, richness and diversity. These findings demonstrated that this EMBR enhanced pollutant removal and mitigated membrane fouling simultaneously, highlighting the potential of the novel technology to be used for removing PPCPs from wastewater.

Development of an Electrochemical Ceramic Membrane Bioreactor for the Removal of PPCPs from Wastewater

The removal of pharmaceutical and personal care products (PPCPs) from water and wastewater is of great significance for eco-system safety. In this study, an electrochemical ceramic membrane bioreactor (ECMBR) was developed for removing seven groups (24 kinds in total) of PPCPs from real wastewater. In the presence of an electric field (2 V/cm), the ECMBR could enhance the removal efficiencies for most targeted PPCPs without having adverse impacts on conventional pollutant removal and membrane filtration. The ECMBR achieved higher removal efficiencies for fluoroquinolones (82.8%), β-blockers (24.6%), and sulfonamides (41.0%) compared to the control (CMBR) (52.9%, 4.6%, and 36.4%). For trimethoprim, ECMBR also significantly increased the removal to 66.5% compared to 15.6% in CMBR. Furthermore, the exertion of an electric field did not cause significant changes in microbial communities, suggesting that the enhanced removal of PPCPs should be attributed to the electrochemical oxidation of the built-in electrodes in the ECMBR.

Degradation of sulfamethoxazole in low-C/N ratio wastewater by a novel membrane bioelectrochemical reactor

Sulfamethoxazole (SMX) pollution in wastewater threatens public health. A novel membrane bioelectrochemical reactor (MBER) with loop operation was developed for SMX degradation in low-C/N ratio wastewater. A gas-permeable silicone membrane module was used to precisely control the dissolved oxygen in the catholyte and save energy. Compared with a traditional membrane bioreactor (i.e., open-circuit reactor), the removal of SMX was increased from 49.91% to 71.10% in the proposed MBER (i.e., closed-circuit reactor). Sequencing analyses revealed that SMX was removed via cometabolism with NH4+-N and COD removal in both the anode and cathode chambers. Six intermediates were detected as degradation products in the cathodic effluent; these intermediates pose a similar potential threat to the environment as SMX. Two possible degradation pathways, deduced from the sequencing analyses and degradation products, were proposed. These results provide a new technology for improving SMX removal through the integration/coupling of bioelectrochemical technology into a membrane bioreactor.

Granular activated carbon assisted nitrate-dependent anaerobic methane oxidation-membrane bioreactor: Strengthening effect and mechanisms

Eutrophication and global warming are two main urgent environmental problems around the world. Nitrate-dependent Anaerobic Methane Oxidation (NdAMO) is a bioprocess coupling nitrate reduction with anaerobic methane oxidation, which could mitigate of these two environmental issues simultaneously. In this study, a newly granular active carbon-NdAMO-membrane bioreactor (GAC-NdAMO-MBR) system was established to evaluate its nitrogen removal efficiency, membrane fouling property and the probable strengthening mechanism was also uncovered. Results indicated that the nitrate removal rate in GAC-NdAMO-MBR reached 31.85 ± 3.19 mgN·L^-1·d^-1 while it was only 10.35 ± 2.02 mgN·L^-1·d^-1 in NdAMO-MBR system (lack of GAC), which was multiplied three-fold. The membrane flux decay rate of GAC- NdAMO -MBR was 0.15 L/m²·h·d while it was 0.49 L/m²·h·d without GAC, and the addition of GAC could extend membrane fouling time for 2.5 times. Notablely, the relative abundance of NdAMO bacteria sharply increased from 27.15% to 56.91% after GAC addition while the NdAMO archaea showed similar variation trend. The physicochemical property of GAC mainly contributed the strengthening effect. The porous structure of GAC absorbed methane and adhered by microorganism, which enhance microorganism amount and metabolic activity. The mechanical strength of GAC scoured membrane surface to mitigate external fouling and pores absorbed EPS to reduce internal fouling. The combined effects could improve NdAMO microorganism growth and metabolism activity and finally improved nitrogen removal performance and controlled membrane fouling. These findings could deep the knowledge of NdAMO process and help extend its application potential in environment science and engineering.

Towards a simultaneous combination of ozonation and biodegradation for enhancing tetracycline decomposition and toxicity elimination

In this study, a new intimately coupling technology of advanced oxidation and biodegradation was proposed, called simultaneous combination of ozonation and biodegradation (SCOB), which uses ozonation in place of traditional photocatalysis. SCOB was evaluated for its ability to degrade and detoxify tetracycline hydrochloride (TCH). Biodegradation alone only resulted in negligible TCH removal, while ozone alone caused less effective performance, with TCH degradation rate constants of 29-171% lower than those of SCOB. The optimal ozone dose was 2.0 mg-O₃/(L·h), and it contributed to remove 97% of the TCH within 2 h under SCOB operation. The SCOB effluent was not toxic to S. aureus after 8 h of exposure. During six SCOB operation cycles, the biomass in the biofilm remained stable, and cell structure was relatively intact. SCOB significantly improved TCH degradation and reduced toxicity of the effluent.