Development and physicochemical characterization of alginate composite film loaded with simvastatin as a potential wound dressing

Creating ultra-strong and recyclable green plastics from marine-sourced alginate-chitosan nanowhisker nanocomposites for controlled release urea fertilizer

In response to the pressing environmental challenge posed by petroleum-derived plastics, the development of green plastics derived from all-biomass nanocomposites offers promising solutions. However, conventional nanocomposites often prioritize enhanced stiffness at the expense of flexibility. We introduce sodium alginate (SA)/chitosan nanowhisker (CSW) nanocomposites, derived entirely from marine-sourced all-biomass, to create ultra-strong and flexible green plastics. Through the synergistic interaction between SA and CSW, these nanocomposites demonstrate simultaneous stiffening and toughening, overcoming the traditional trade-off. Two key mechanisms contribute: geometric reinforcement from the needle-like structure of CSW and electrostatic reinforcement at the interface between oppositely charged CSW and SA. Compared to control SA, the SA/CSW nanocomposites exhibit remarkable enhancements in tensile modulus, strength, and stretchability, by 49%, 85%, and 55%, respectively (7.6 GPa, 223.3 MPa, 14.7%). Cellulose nanocrystals, serving as a control, only stiffen the nanocomposites, adhering to the typical trade-off. Biodegradability in compost can be tailored based on the type of nanofillers. Due to the water resistance of CSW, SA/CSW nanocomposites are proven effective for the controlled release of urea fertilizer in agricultural applications. With recyclability and superior mechanical properties, these marine-sourced green plastics offer a sustainable alternative to conventional plastics, promising significant impact in the eco-plastic industry.

Comprehensive developmental investigation on simvastatin enriched bioactive film forming spray using the quality by design paradigm: a prospective strategy for improved wound healing

The use of topical antimicrobials in wound healing presents challenges like risk of drug resistance and toxicity to local tissue. Simvastatin (SIM), a lipid-lowering agent which reduces the risk of cardiovascular events, is repurposed for its pleiotropic effect in wound healing. A bioactive bioadhesive polymer-based film forming spray (FFS) formulation of SIM was designed using chitosan, collagen, hyaluronic acid and optimised by employing the DoE approach. Optimised formulation demonstrated moderate viscosity (12.5 ± 0.3 cP), rapid film formation (231 ± 5.6 s), flexibility, tensile strength and sustained drug release (T80 - time for 80% drug release - 9.05 ± 0.7 h). Scanning electron microscopy (SEM) verified uniformly dispersed drug within the composite polymer matrix. SIM FFS demonstrated antimicrobial activity against gram positive and gram negative bacteria. In vivo excision wound model studies in mice affirmed the beneficent role of bioactive polymers and the efficacy of SIM FFS in wound contraction and closure, tissue remodelling and re-epithelization in comparison to standard antimicrobial preparation. Cytokines TNF- alpha, IL-6 were downregulated and IL-10 was upregulated. Biochemical markers; hydroxyproline, hexosamine and histopathology were consistent with wound contraction observed. This is an exploratory effort in repurposing SIM for wound healing in a novel dosage form, underscoring its potential as an alternative to conventional topical antimicrobials.

Production and characterization of bacterial cellulose synthesized by Enterobacter chuandaensis strain AEC using Phoenix dactylifera and Musa acuminata

Bacterial cellulose (BC) is a biopolymer synthesized extracellularly by certain bacteria through the polymerization of glucose monomers. This study aimed to produce BC using Enterobacter chuandaensis with fruit extracts from Phoenix dactylifera (D) and Musa acuminata (M) as carbon sources. Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR) showed characteristic cellulose vibrations, while X-ray diffraction (XRD) identified distinct peaks at 15.34°, 19.98°, 22.58°, and 34.6°, confirming the cellulose structure. Whole-genome sequencing of E. chuandaensis identified key genes involved in BC production. The BC produced then exhibited a molecular weight of 1,857,804 g/mol, with yields of 2.8 g/L and 2.5 g/L for treatments D and M, respectively. The crystallinity index of the purified BC was 74.1, and 13C NMR analysis confirmed the dominant cellulose Iα crystalline form. The BC showed high biocompatibility in cytotoxicity assays, with cell viability between 92% and 100%, indicating its potential for use in biomedical applications. This investigation represents the first report of BC production by E. chuandaensis, which promises a new avenue for sustainable and efficient BC synthesis using fruit extracts as carbon sources.

Production and analysis of synthesized bacterial cellulose by Enterococcus faecalis strain AEF using Phoenix dactylifera and Musa acuminata fruit extracts

Bacterial cellulose (BC) is a highly versatile biopolymer renowned for its exceptional mechanical strength, water retention, and biocompatibility. These properties make it a valuable material for various industrial and biomedical applications. In this study, Enterococcus faecalis synthesized extracellular BC, utilizing Phoenix dactylifera and Musa acuminata fruit extracts as sustainable carbon sources. LC-MS analysis identified glucose as the primary carbohydrate in these extracts, providing a suitable substrate for BC production. Scanning Electron Microscopy (SEM) revealed a network of BC nanofibers on Congo red agar plates. ATR-FTIR spectroscopy confirmed the presence of characteristic cellulose functional groups, further supporting BC synthesis. X-ray diffraction (XRD) analysis indicated a high crystallinity index of 71%, consistent with the cellulose I structure, as evidenced by peaks at 16.22°, 21.46°, 22.52°, and 34.70°. Whole-genome sequencing of E. faecalis identified vital genes involved in BC biosynthesis, including bcsA, bcsB, diguanylate cyclase (DGC), and 6-phosphofructokinase (pfkA). Antibiotic susceptibility tests revealed resistance to cefotaxime, ceftazidime, and ceftriaxone, while susceptibility to imipenem was observed. Quantitative assessment demonstrated that higher concentrations of fruit extracts (5.0-20 mg/mL) significantly enhanced BC production. Cytotoxicity testing via the MTT assay confirmed excellent biocompatibility with NIH/3T3 fibroblast cells, showing high cell viability (97-105%). Unlike commonly studied Gram-negative bacteria like Acetobacter xylinum for BC production, this research focuses on Gram-positive Enterococcus faecalis and utilizes Phoenix dactylifera and Musa acuminata fruit extracts as carbon sources. This approach offers a sustainable and promising avenue for BC production.

Developmental prospects of carrageenan-based wound dressing films: Unveiling techno-functional properties and freeze-drying technology for the development of absorbent films - A review

This review explores the intricate wound healing process, emphasizing the critical role of dressing material selection, particularly for chronic wounds with high exudate levels. The aim is to tailor biodegradable dressings for comprehensive healing, focusing on maximizing moisture retention, a vital element for adequate recovery. Researchers are designing advanced wound dressings that enhance techno-functional and bioactive properties, minimizing healing time and ensuring cost-effective care. The study delves into wound dressing materials, highlighting carrageenan biocomposites superior attributes and potential in advancing wound care. Carrageenan's versatility in various biomedical applications demonstrates its potential for tissue repair, bone regeneration, and drug delivery. Ongoing research explores synergistic effects by combining carrageenan with other novel materials, aiming for complete biocompatibility. As innovative solutions emerge, carrageenan-based wound-healing medical devices are poised for global accessibility, addressing challenges associated with the complex wound-healing process. The exceptional physico-mechanical properties of carrageenan make it well-suited for highly exudating wounds, offering a promising avenue to revolutionize wound care through freeze-drying techniques. This thorough approach to evaluating the wound healing effectiveness of carrageenan-based films, particularly emphasizing the development potential of lyophilized films, has the potential to significantly improve the quality of life for patients receiving wound healing treatments.

Preparation and characterization of a ciprofloxacin-loaded nanoparticles incorporated polymeric film dressing

In an effort to prepare a modern polysaccharide-based dressing for sustained/prolonged delivery of the antibacterial agent to prevent and control skin wound infection, ciprofloxacin (CP)-loaded sodium alginate (SA)-chitosan (CS) nanoparticles (NPs) were incorporated into novel arabinoxylan (AX)-pectin (PC) blended polymeric films by solvent casting. The CP-NPs were prepared by a two-step ionic interaction method with < 300 nm size, about 25 mV zeta potential, 74% CP-loading efficiency, and approximately round shape. The CP-NPs were incorporated in optimized AX-PC polymeric film prepared by using 2% AX and 2% PC with a plasticizer (2% glycerol) and then these films were characterized for suitability as a film dressing. The transparency, improved mechanical strength, thermal stability, water transmission, and exudate uptake characteristics indicated that CP-NPs incorporated AX-PC polymeric films were suitable for dressing applications. The CP-NPs incorporated AX-PC films exhibited sustained CP release (90% release in 36 h) and better antibacterial susceptibility as compared to free CP-containing AX-PC films. Thus, CP-NPs incorporated AX-PC films are promising dressing materials to prevent and control wound infection with prolonged antibiotic release.

Carboxymethyl cellulose/sodium alginate hydrogel with anti-inflammatory capabilities for accelerated wound healing; In vitro and in vivo study

Recently, managing the chronic skin wounds has become increasingly challenging for healthcare professionals due to the intricate orchestration of cellular and molecular processes involved that lead to the uncontrollable inflammatory reactions which hinder the healing process. Therefore, different types of wound dressings with immunomodulatory properties have been developed in recent years to effectively regulate the immune responses, enhance angiogenesis, promote re-epithelialization, and accelerate the wound healing process. This study aims to develop a new type of immunomodulatory wound dressing utilizing carboxymethyl cellulose (CMC)/sodium alginate (Alg)-simvastatin (SIM) to simultaneously enhance the inflammatory responses and the wound healing ratio. The CMC/Alg-SIM hydrogels exhibited appropriate swelling ratio, water vapor transmission rate, and desirable degradation rate, depending on the SIM content. The fabricated dressing showed sustained release of SIM (during 5 days) that improved the proliferation of skin cells. According to the in vitro findings, the CMC/Alg-SIM hydrogel exhibited controlled pro-inflammatory responses (decreased 2.5- and 1.6-times IL-6 and TNF-α, respectively) and improved secretion of anti-inflammatory cytokines (increased 1.5- and 1.3-times IL-10 and TGF-β, respectively) in comparison with CMC/Alg. Furthermore, the CMC/Alg-SIM hydrogel facilitated rapid wound healing in the rat model with a full-thickness skin defect. After 14 days post-surgery, the wound healing ratio in the CMC/Alg hydrogel group (∼93%) was significantly greater than the control group (∼58%). Therefore, the engineered CMC/Alg-SIM hydrogel with desired immunomodulatory properties possesses the potential to enhance and accelerate skin regeneration for the management of chronic wound healing.

An Immune-Regulating Polysaccharide Hybrid Hydrogel with Mild Photothermal Effect and Anti-Inflammatory for Accelerating Infected Wound Healing

Bacterial infections and excessive inflammation present substantial challenges for clinical wound healing. Hydrogels with mild photothermal (PTT) effects have emerged as promising agents owing to their dual actions: positive effects on cells and negative effects on bacteria. Here, an injectable self-healing hydrogel of oxidized konjac glucomannan/arginine-modified chitosan (OKGM/CS-Arg, OC) integrated with protocatechualdehyde-@Fe (PF) nanoparticles capable of effectively absorbing near-infrared radiation is synthesized successfully. The OC/PF hydrogels exhibit excellent mechanical properties, biocompatibility, and antioxidant activity. Moreover, in synergy with PTT, OC/PF demonstrates potent antibacterial effects while concurrently stimulating cell migration and new blood vessel formation. In methicillin-resistant Staphylococcus aureus-infected full-thickness mouse wounds, the OC/PF hydrogel displays remarkable antibacterial and anti-inflammatory activities, and accelerates wound healing by regulating the wound immune microenvironment and promoting M2 macrophage polarization. Consequently, the OC/PF hydrogel represents a novel therapeutic approach for treating multidrug-resistant bacterial infections and offers a technologically advanced solution for managing infectious wounds in clinical settings.

Optimizing ultrasound-assisted extraction of bioactive compounds from Canthium horridum blume leaves utilizing polyols: A study on skin-related activities

The focus on reducing organic solvent usage, owing to their negative environmental and health impacts, is driving a search for innovative green alternative solvents in academia and industry. Canthium horridum Blume (CH) exhibits many therapeutic activities, including antioxidant and anti-inflammatory efficacy. The objective of this study is to evaluate the optimal solvent concentration using a simplex-lattice design with an aqueous-polyols mixture and to optimize the parameters for extracting bioactive compounds and antioxidant activities from ultrasound-assisted extraction (UAE) of CH leaves through central composite design (CCD) in response surface methodology (RSM). This study examines the total phenolic content (TPC), antioxidant activities, comparison of different extraction conditions, identification of bioactive compounds, cell cytotoxicity, cellular antioxidant activity, and melanin content reduction efficacy of the extracts. According to the findings from the simplex-lattice model, the ideal solvent composition consisted of 32.57%w/w butylene glycol, 32.92%w/w glycerine, and 34.51%w/w water. Furthermore, based on the response model, optimal extraction conditions were identified as a 15-min extraction time and a solvent-to-sample ratio of 32.94:1. In comparison to alternative extraction methods, ultrasonic-assisted extraction using the aqueous-glycerine-butylene glycol (GB-UAE) extract resulted in notably elevated TPC and antioxidant responses (p < 0.05). Major antioxidant bioactive compounds included 4-(Butoxymethyl) phenol, 3-O-Caffeoyl-4-O-methylquinic acid, Quercetin 3-(2G-glucosylrutinoside), 2,4-Dihydroxybenzoic acid and other bioactive compounds. The GB-UAE extract revealed greater cell viability than UAE using ethanol (EtOH-UAE) extract in both cytotoxicity and cellular antioxidant assays at the same concentration. Additionally, it exhibited comparable melanin content reduction efficacy at a higher concentration compared to that of EtOH-UAE extract. The researcher anticipates that the current study will advance the utilization of an aqueous-polyols system for extracting bioactive compounds extending beyond CH leaves. Although the potential applications of CH leaves in cosmetics and pharmaceutical formulations have been identified, further comprehensive mechanistic and clinical studies are required to fully understand their effects.

A novel approach to wound healing: Green synthetic nano-zinc oxide embedded with sodium alginate and polyvinyl alcohol hydrogels for dressings

Wound healing constitutes a formidable challenge within the healthcare system, attributable to infection risks and protracted recovery periods. The pressing need for innovative wound healing methods has spurred the urgency to develop novel approaches. This study sought to advance wound healing by introducing a novel approach employing a composite sponge dressing. The composite sponge dressing, derived from LFL-ZnO (synthesized through the green methodology utilizing Lactobacillus plantarum ZDY2013 fermentation liquid), polyvinyl alcohol (PVA), and sodium alginate (SA) via a freeze-thaw cycle and freeze-drying molding process, demonstrated notable properties. The findings elucidate the commendable swelling, moisturizing, and mechanical attributes of the SA/LFL-ZnO/PVA composite sponge dressing, characterized by a porous structure. Remarkably, the dressing incorporating LFL-ZnO exhibited substantial inhibition against both methicillin-resistant Staphylococcus aureus (MRSA) and Staphylococcus aureus (S. aureus). Hemolysis and cytotoxicity tests corroborated the excellent biocompatibility of the sponge dressing. In vivo evaluation of the therapeutic efficacy of the 1 mg/mL LFL-ZnO composite dressing on scald wounds and S. aureus-infected wounds revealed its capacity to accelerate wound healing and exert pronounced antibacterial effects. Consequently, the composite sponge dressings synthesized in this study hold significant potential for application in wound treatment.

Integration of polysaccharide electrospun nanofibers with microneedle arrays promotes wound regeneration: A review

Utilizing electrospun nanofibers and microneedle arrays in wound regeneration has been practiced for several years. Researchers have recently asserted that using multiple methods concurrently might enhance efficiency, despite the inherent strengths and weaknesses of each individual approach. The combination of microneedle arrays with electrospun nanofibers has the potential to create a drug delivery system and wound healing method that offer improved efficiency and accuracy in targeting. The use of microneedles with nanofibers allows for precise administration of pharmaceuticals due to the microneedles' capacity to pierce the skin and the nanofibers' role as a drug reservoir, resulting in a progressive release of drugs over a certain period of time. Electrospun nanofibers have the ability to imitate the extracellular matrix and provide a framework for cellular growth and tissue rejuvenation, while microneedle arrays show potential for enhancing tissue regeneration and enhancing the efficacy of wound healing. The integration of electrospun nanofibers with microneedle arrays may be customized to effectively tackle particular obstacles in the fields of wound healing and drug delivery. However, some issues must be addressed before this paradigm may be fully integrated into clinical settings, including but not limited to ensuring the safety and sterilization of these products for transdermal use, optimizing manufacturing methods and characterization of developed products, larger-scale production, optimizing storage conditions, and evaluating the inclusion of multiple therapeutic and antimicrobial agents to increase the synergistic effects in the wound healing process. This research examines the combination of microneedle arrays with electrospun nanofibers to enhance the delivery of drugs and promote wound healing. It explores various kinds of microneedle arrays, the materials and processes used, and current developments in their integration with electrospun nanofibers.

3D printed polylactic acid-based nanocomposite scaffold stuffed with microporous simvastatin-loaded polyelectrolyte for craniofacial reconstruction

Critical sized craniofacial defects are among the most challenging bone defects to repair, due to the anatomical complexity and aesthetic importance. In this study, a polylactic acid/hardystonite-graphene oxide (PLA/HTGO) scaffold was fabricated through 3D printing. In order to upgrade the 3D printed scaffold to a highly porous scaffold, its channels were filled with pectin-quaternized chitosan (Pec-QCs) polyelectrolyte solution containing 0 or 20 mg/mL of simvastatin (Sim) and then freeze-dried. These scaffolds were named FD and FD-Sim, respectively. Also, similar PLA/HTGO scaffolds were prepared and dip coated with Pec-QCs solution containing 0 or 20 mg/mL of Sim and were named DC and DC-Sim, respectively. The formation of macro/microporous structure was confirmed by morphological investigations. The release of Sim from DC-Sim and FD-Sim scaffolds after 28 days was measured as 77.40 ± 5.25 and 86.02 ± 3.63 %, respectively. Cytocompatibility assessments showed that MG-63 cells had the highest proliferation, attachment and spread on the Sim containing scaffolds, especially FD-Sim. In vivo studies on a rat calvarial defect model revealed that an almost complete recovery occurred in the group treated with FD-Sim scaffold after 8 weeks and the defect was filled with newly formed bone. The results of this study acknowledge that the FD-Sim scaffold can be a perfect candidate for calvarial defect repair.

Aloe vera-based biomaterial ink for 3D bioprinting of wound dressing constructs

This study emphasizes the development of a multifunctional biomaterial ink for wound healing constructs. The biomaterial ink benefits from Aloe vera's intrinsic biocompatible, biodegradable, antioxidant, antimicrobial, anti-inflammatory, and immunomodulatory attributes, thus alleviating the need for supplementary substances employed to combat infections and stimulate tissue regeneration. Moreover, this biomaterial ink seeks to address the scarcity of standardized printable materials possessing adequate biocompatibility and physicochemical properties, which hinder its widespread clinical adoption. The biomaterial ink was synthesized via ionic crosslinking to enhance its rheological and mechanical characteristics. The findings revealed that Aloe vera substantially boosted the hydrogel's viscoelastic behavior, enabling superior compressive modulus and the extrusion of fine filaments. The bioprinted constructs exhibited desirable resolution and mechanical strength while displaying a porous microstructure analogous to the native extracellular matrix. Biological response demonstrated no detrimental impact on stem cell viability upon exposure to the biomaterial ink, as confirmed by live/dead assays. These outcomes validate the potential of the developed biomaterial ink as a resource for the bioprinting of wound dressings that effectively foster cellular proliferation, thereby promoting enhanced wound healing by leveraging Aloe vera's inherent properties.

3D-Printed Alginate/Pectin-Based Patches Loaded with Olive Leaf Extracts for Wound Healing Applications: Development, Characterization and In Vitro Evaluation of Biological Properties

Traditional wound dressings may lack suitability for diverse wound types and individual patient requirements. In this context, this study aimed to innovate wound care by developing a 3D-printed patch using alginate and pectin and incorporating Olive Leaf Extract (OLE) as an active ingredient. Different polymer-to-plasticizer ratios were systematically examined to formulate a printable ink with optimal viscosity. The resultant film, enriched with OLE, exhibited a substantial polyphenolic content of 13.15 ± 0.41 mg CAE/g, showcasing significant antioxidant and anti-inflammatory properties. Notably, the film demonstrated potent scavenging abilities against DPPH, ABTS, and NO radicals, with IC50 values of 0.66 ± 0.07, 0.47 ± 0.04, and 2.02 ± 0.14 mg/mL, respectively. In vitro release and diffusion studies were carried out and the release profiles revealed an almost complete release of polyphenols from the patch within 48 h. Additionally, the fabricated film exhibited the capacity to enhance cell motility and accelerate wound healing, evidenced by increased collagen I expression in BJ fibroblast cells. Structural assessments affirmed the ability of the patch to absorb exudates and maintain the optimal moisture balance, while biocompatibility studies underscored its suitability for biomedical applications. These compelling findings endorse the potential application of the developed film in advanced wound care, with the prospect of tailoring patches to individual patient needs.

Development of a Novel Covalently Bonded Conjugate of Caprylic Acid Tripeptide (Isoleucine-Leucine-Aspartic Acid) for Wound-Compatible and Injectable Hydrogel to Accelerate Healing

Third-degree burn injuries pose a significant health threat. Safer, easier-to-use, and more effective techniques are urgently needed for their treatment. We hypothesized that covalently bonded conjugates of fatty acids and tripeptides can form wound-compatible hydrogels that can accelerate healing. We first designed conjugated structures as fatty acid-aminoacid1-amonoacid2-aspartate amphiphiles (Cn acid-AA1-AA2-D), which were potentially capable of self-assembling into hydrogels according to the structure and properties of each moiety. We then generated 14 novel conjugates based on this design by using two Fmoc/tBu solid-phase peptide synthesis techniques; we verified their structures and purities through liquid chromatography with tandem mass spectrometry and nuclear magnetic resonance spectroscopy. Of them, 13 conjugates formed hydrogels at low concentrations (≥0.25% w/v), but C8 acid-ILD-NH2 showed the best hydrogelation and was investigated further. Scanning electron microscopy revealed that C8 acid-ILD-NH2 formed fibrous network structures and rapidly formed hydrogels that were stable in phosphate-buffered saline (pH 2-8, 37 °C), a typical pathophysiological condition. Injection and rheological studies revealed that the hydrogels manifested important wound treatment properties, including injectability, shear thinning, rapid re-gelation, and wound-compatible mechanics (e.g., moduli G″ and G', ~0.5-15 kPa). The C8 acid-ILD-NH2(2) hydrogel markedly accelerated the healing of third-degree burn wounds on C57BL/6J mice. Taken together, our findings demonstrated the potential of the Cn fatty acid-AA1-AA2-D molecular template to form hydrogels capable of promoting the wound healing of third-degree burns.

Development and In Vitro Evaluation of Aceclofenac Buccal Film

AIM

This study aimed to formulate and characterize aceclofenac buccal film formulations made of different polymers and evaluate the effects of polymer type on buccal film properties.

MATERIALS AND METHODS

Five polymer types, namely hydroxypropyl methylcellulose (HPMC), sodium carboxymethylcellulose (SCMC), polyvinyl alcohol (PVA), Eudragit S100, and Eudragit SR100, were used to prepare aceclofenac buccal film formulation either separately or combined by solvent-casting method. These formulations were evaluated in terms of physical appearance, folding test, film weight and thickness, drug content, percentage of elongation, moisture uptake, water vapor permeability, and in vitro drug release.

RESULTS

The addition of Eudragit polymer in most of the produced buccal films was unacceptable with low folding endurance. However, the dissolution profile of buccal films made from PVA and Eudragit SR100 provided a controlled drug release profile.

CONCLUSION

Buccal films can be formulated using different polymers either individually or in combination to obtain the drug release profile required to achieve a desired treatment goal. Furthermore, the property of the buccal films depends on the type and concentration of the polymer used.

TiB2-Derived Nanosheets Enhance the Tensile Strength and Controlled Drug Release of Biopolymeric Films Used in Wound Healing

Wound healing using an alginate-based biopolymeric film is one of the most preferred treatments. However, these films lack mechanical strength (elasticity and tensile strength), show higher initial burst release, and exhibit high vapor permeability. The present study reports the development of nanosheets derived from titanium diboride (10 nm) (NTB)-incorporated biopolymeric films (0.025, 0.05, and 0.1% w/v) using sodium alginate (SA) and carboxymethyl cellulose (CMC) to overcome the shortfalls. The surface properties of the film, nanosheet distribution within the film, and possible interactions with the film are explored by using scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), Fourier transform infrared (FTIR), and X-ray diffraction (XRD). These analyses confirm that nanosheets are uniformly distributed in the film and introduce unevenness on the film's surface. The tensile strength of the nanosheet-incorporated film (0.1% NTB film) using UTM is found to be 24.30 MPa (six times higher compared to the blank film), equivalent to human skin. The water vapor transmission rate of the film is also found to be in the desired range (i.e., 2000-2500 g/m2 day). The biocompatibility of the NTB film is confirmed by the MTT assay test using NIH/3T3 cells and HEK 293 cells. Furthermore, the scratch assay shows that the developed films promote cell migration and proliferation. The antibacterial activity of the film is also demonstrated using a model drug, tetracycline hydrochloride (TCl). Besides, the film exhibits the sustained release of TCl and follows the Korsmeyer-Peppas model for drug release. Overall, the 0.1% w/v NTB film is easy to fabricate, biocompatible and shows superior mechanical properties.

Characterization and Bio-Evaluation of the Synergistic Effect of Simvastatin and Folic Acid as Wound Dressings on the Healing Process

Wound healing is a significant healthcare problem that decreases the patient's quality of life. Hence, several agents and approaches have been widely used to help accelerate wound healing. The challenge is to search for a topical delivery system that could supply long-acting effects, accurate doses, and rapid healing activity. Topical forms of simvastatin (SMV) are beneficial in wound care. This study aimed to develop a novel topical chitosan-based platform of SMV with folic acid (FA) for wound healing. Moreover, the synergistic effect of combinations was determined in an excisional wound model in rats. The prepared SMV-FA-loaded films (SMV-FAPFs) were examined for their physicochemical characterizations and morphology. Box-Behnken Design and response surface methodology were used to evaluate the tensile strength and release characteristics of the prepared SMV-FAPFs. Additionally, Fourier transform infrared (FT-IR), differential scanning calorimetry (DSC), X-ray diffraction pattern (XRD), and animal studies were also investigated. The developed SMV-FAPFs showed a contraction of up to 80% decrease in the wound size after ten days. The results of the quantitative real-time polymerase chain reaction (RT-PCR) analysis demonstrated a significant upregulation of dermal collagen type I (CoTI) expression and downregulation of the inflammatory JAK3 expression in wounds treated with SMV-FAPFs when compared to control samples and individual drug treatments. In summary, it can be concluded that the utilization of SMV-FAPFs holds great potential for facilitating efficient and expeditious wound healing, hence presenting a feasible substitute for conventional topical administration methods.

Optimization and Characterization of a Novel Antioxidant Naringenin-Loaded Hydrogel for Encouraging Re-Epithelization in Chronic Diabetic Wounds: A Preclinical Study

Nonhealed wounds are one of the most dangerous side effects of type-2 diabetes, which is linked to a high frequency of bacterial infections around the globe that eventually results in amputation of limbs. The present investigation aimed to explore the drug-loaded (naringenin) hydrogel system for chronic wound healing. The hydrogel membranes comprising Na-alginate with F-127 and poly(vinyl alcohol) were developed to treat chronic wounds using the quality-by-design (QbD) approach. The optimized formulation was tested for various parameters, such as swelling, gel fraction, water vapor transition rate (WVTR), etc. In vitro evaluation indicated that a drug-loaded hydrogel displayed better tissue adhesiveness and can release drugs for a prolonged duration of 12 h. Scratch assay performed on L929 cell lines demonstrated good cell migration. The diabetic wound healing potential of the hydrogel membrane was assessed in streptozotocin-induced male Wistar rats (50 mg/kg). Higher rates of wound closure, re-epithelialization, and accumulation of collagen were seen in in vivo experiments. Histopathologic investigation correspondingly implied that the drug-loaded hydrogel could enhance dermal wound repair. The improved antimicrobial and antioxidant properties with expedited healing indicated that the drug-loaded hydrogel is a perfect dressing for chronic wounds.

Optimization of the Green Extraction of Red Araçá (Psidium catteyanum Sabine) and Application in Alginate Membranes for Use as Dressings

In this research, the aim was to introduce innovation to the pharmaceutical field through the exploration of an underutilized plant matrix, the red araçá, along with the utilization of sodium alginate for the development of membranes designed for active topical dressings. Within this context, optimal extraction conditions were investigated using the central composite rotational statistical design (CCRD) to obtain a red araçá epicarp extract (RAEE) rich in bioactive compounds utilizing the maceration technique. The extract acquired under the optimized conditions (temperature of 66 °C and a hydroalcoholic solvent concentration of 32%) was incorporated into a sodium alginate matrix for the production of active membranes using a casting method. Characterization of the membranes revealed that the addition of the extract did not significantly alter its morphology. Furthermore, satisfactory results were observed regarding mechanical and barrier properties, as well as the controlled release of phenolic compounds in an environment simulating wound exudate. Based on these findings, the material produced from renewable matrices demonstrates the promising potential for application as a topical dressing within the pharmaceutical industry.

Exploration of curcumin-incorporated dual anionic alginate-quince seed gum films for transdermal drug delivery

The idea of combining bioextracted polymers for wound healing applications has emerged in hopes of developing highly flexible and mechanically stable hydrogel films with controlled drug delivery, biocompatibility, and high collagen deposition. In the present research, polysaccharide films composed of Alginate and Quince Seed Gum (QSG) were fabricated by ionic crosslinking, and their potential for curcumin delivery and wound healing were examined. In this regard, microstructure, mechanical properties, thermal stability, physiochemical properties, and biocompatibility of films with three different QSG amounts (25 %, 50 %, and 75 %) were studied. Because of the optimum properties of 25 % QSG films like better transparency (Opacity = 6.1 %), higher flexibility (Elongation = 28.9 %), less water solubility (Water solubility = 66.6 %), proper absorbance (Swelling degree = >600 %), and suitable biocompatibility (Cell viability = >85 %), they were used for drug delivery examination. Curcumin administration through films with and without stearic acid modification was investigated. Stearic Acid (SA) modified samples demonstrated superior compatibility between hydrophobic drug and hydrophilic film. Stearic acid-modified film could prolong the curcumin release up to 48 h and showed increased collagen synthesis and TGF-β expression, making it an excellent candidate for transdermal drug delivery and wound healing applications.

Progress in the application of 3D-printed sodium alginate-based hydrogel scaffolds in bone tissue repair

In recent years, hydrogels have been widely used in the biomedical field as materials with excellent bionic structures and biological properties. Among them, the excellent comprehensive properties of natural polymer hydrogels represented by sodium alginate have attracted the great attention of researchers. At the same time, by physically blending sodium alginate with other materials, the problems of poor cell adhesion and mechanical properties of sodium alginate hydrogels were directly improved without chemical modification of sodium alginate. The composite blending of multiple materials can also improve the functionality of sodium alginate hydrogels, and the prepared composite hydrogel also has a larger application field. In addition, based on the adjustable viscosity of sodium alginate-based hydrogels, sodium alginate-based hydrogels can be loaded with cells to prepare biological ink, and the scaffold can be printed out by 3D printing technology for the repair of bone defects. This paper first summarizes the improvement of the properties of sodium alginate and other materials after physical blending. Then, it summarizes the application progress of sodium alginate-based hydrogel scaffolds for bone tissue repair based on 3D printing technology in recent years. Moreover, we provide relevant opinions and comments to provide a theoretical basis for follow-up research.

Natural TEMPO oxidized cellulose nano fiber/alginate/dSECM hybrid aerogel with improved wound healing and hemostatic ability

Natural biopolymers have attracted considerable attention in a variety of biomedical applications. Herein, tempo-oxidized-cellulose nanofibers (T) were incorporated into sodium alginate/chitosan (A/C) to reinforce the physicochemical properties and further modified with decellularized skin extracellular matrix (E). A unique ACTE aerogel was successfully prepared, and its nontoxic behavior was validated using mouse fibroblast L929 cells. In vitro hemolysis results revealed excellent platelet adhesion and fibrin network formation abilities of the obtained aerogel. A high speed of homeostasis was attained based on the quick clotting in <60 s. Skin regeneration in vivo experiments were conducted using the ACT1E0 and ACT1E10 groups. In comparison to ACT1E0 samples, ACT1E10 samples demonstrated enhanced skin wound healing with increased neo-epithelialization, increased collagen deposition, and extracellular matrix remodeling. ACT1E10 was found to be a promising aerogel for skin defect regeneration due to its improved wound-healing ability.

Rectifying disorder of extracellular matrix to suppress urethral stricture by protein nanofilm-controlled drug delivery from urinary catheter

Urethral stricture secondary to urethral injury, afflicting both patients and urologists, is initiated by excessive deposition of extracellular matrix in the submucosal and periurethral tissues. Although various anti-fibrotic drugs have been applied to urethral stricture by irrigation or submucosal injection, their clinical feasibility and effectiveness are limited. Here, to target the pathological state of the extracellular matrix, we design a protein-based nanofilm-controlled drug delivery system and assemble it on the catheter. This approach, which integrates excellent anti-biofilm properties with stable and controlled drug delivery for tens of days in one step, ensures optimal efficacy and negligible side effects while preventing biofilm-related infections. In a rabbit model of urethral injury, the anti-fibrotic catheter maintains extracellular matrix homeostasis by reducing fibroblast-derived collagen production and enhancing metalloproteinase 1-induced collagen degradation, resulting in a greater improvement in lumen stenosis than other topical therapies for urethral stricture prevention. Such facilely fabricated biocompatible coating with antibacterial contamination and sustained-drug-release functionality could not only benefit populations at high risk of urethral stricture but also serve as an advanced paradigm for a range of biomedical applications.

Fabrication and Assessment of Orodispersible Tablets Loaded with Cubosomes for the Improved Anticancer Activity of Simvastatin against the MDA-MB-231 Breast Cancer Cell Line

Various factors limit the use of simvastatin as an anticancer drug. Therefore, this study aimed to analyse simvastatin (SIM)-loaded cubosome efficacy against breast cancer. SIM-loaded cubosomes were prepared using the emulsification method using different glyceryl monooleate, Pluronic F127 (PF-127), and polyvinyl alcohol (PVA) ratios. The best cubosomal formula was subjected to an in vitro cytotoxicity analysis using the human breast cancer cell line, MDA-MB-231 (MDA) (ATCC, HTB-26), and formulated as oral disintegrating tablets through direct compression. PF-127 and PVA positively affected drug loading, and the entrapment efficiency percentage of different SIM-cubosomal formulations ranged from 33.52% to 80.80%. Vesicle size ranged from 181.9 ± 0.50 to 316.6 ± 1.25 nm. PF-127 enhanced in vitro SIM release from cubosome formulations due to its solubilising action on SIM. The in vitro dissolution analysis indicated that SIM exhibited an initial dissolution of 10.4 ± 0.25% within the first 5 min, and 63.5 ± 0.29% of the loaded drug was released after 1 h. Moreover, cubosome formula F3 at 25 and 50 µg/mL doses significantly decreased MDA cell viability compared to the 12.5 µg/mL dose. The untreated SIM suspension and drug-free cubosomes at all doses had no significant influence on MDA cell viability compared to the control.

Dissolvable sodium alginate-based antibacterial wound dressing patches: Design, characterization, and in vitro biological studies

The treatment of infected wounds in patients with highly sensitive skin is challenging. Some of the available wound dressings cause further skin tear and bleeding upon removal thereby hindering the healing process. In this study, dissolvable antibacterial wound dressing patches loaded with cephalexin monohydrate were prepared from different amounts of sodium alginate (SA) and carboxymethyl cellulose (CMC) by the solvent casting evaporation technique. The patches displayed good tensile strength (3.83-13.83 MPa), appropriate thickness (0.09 to 0.31 mm) and good flexibility (74-98 %) suitable for the skin. The patches displayed good biodegradability and low moisture uptake suitable to prevent microbial invasion on the wound dressings upon storage. The release profile of the drug from the patches was sustained in the range of 47-80 % for 48 h, revealing their capability to inhibit bacterial infection. The biological assay showed that the patches did not induce cytotoxic effects on HaCaT cells, revealing good biocompatibility. The antimicrobial effect of the patches on the different strains of bacteria used in the study was significant. The cell migration (66.7-74.3 %) to the scratched gap was promising revealing the patches' capability to promote wound closure. The results obtained show that the wound dressings are potential materials for the treatment of infected wounds.

A Novel Hyaluronic Acid Matrix Ingredient with Regenerative, Anti-Aging and Antioxidant Capacity

Hyaluronic acid (HA) and proteoglycans (such as dermatan sulphate (DS) and chondroitin sulphate (CS)) are the main components of the extracellular matrix of the skin, along with collagen and elastin. These components decrease with age, which implies a loss of skin moisture causing wrinkles, sagging and aging. Currently, the external and internal administration of effective ingredients that can reach the epidermis and dermis is the main alternative for combating skin aging. The objective of this work was to extract, characterise and evaluate the potential of an HA matrix ingredient to support anti-aging. The HA matrix was isolated and purified from rooster comb and characterised physicochemically and molecularly. In addition, its regenerative, anti-aging and antioxidant potential and intestinal absorption were evaluated. The results show that the HA matrix is composed of 67% HA, with an average molecular weight of 1.3 MDa; 12% sulphated glycosaminoglycans, including DS and CS; 17% protein, including collagen (10.4%); and water. The in vitro evaluation of the HA matrix's biological activity showed regenerative properties in both fibroblasts and keratinocytes, as well as moisturising, anti-aging and antioxidant effects. Furthermore, the results suggest that the HA matrix could be absorbed in the intestine, implying a potential oral as well as topical use for skin care, either as an ingredient in a nutraceutical or a cosmetic product.

Butylene Glycol Used as a Sustainable Solvent for Extracting Bioactive Compounds from Camellia sinensis Flowers with Ultrasound-Assisted Extraction

The research aims to assess the yield of bioactive compounds and their antioxidant activities obtained from tea flowers using an ultrasound-assisted extraction method with butylene glycol (BG-UAE) through Box-Behnken design. It investigates the bioactive compounds including the total phenolic content (TPC), total flavonoid content (TFC), and total tannin content (TTC) and analyzes their antioxidant activities, bioactive compound composition by liquid chromatography triple quadrupole tandem mass spectrometry, and their cellular activities via UAE and maceration using BG or ethanol as the solvent. Under optimal conditions, the values of the TPC, TFC, TTC, 1,1-diphenyl-2-picrylhydrazil radical scavenging assay, 2,2'-azino-bis-3-ethylbenzothiazoline-6-sulphonic acid radical scavenging assay, and ferric reducing antioxidant power assay (FRAP) of the BG-UAE extract were 54.00 ± 1.19 mg GAE/g sample, 291.47 ± 3.34 mg QE/g sample, 65.37 ± 1.78 mg TAE/g sample, 106.45 ± 1.21 mg TEAC/g sample, 163.58 ± 2.76 mg TEAC/g sample, and 121.31 ± 4.75 mg FeSO₄/g sample, respectively. Except for FRAP, BG-UAE exhibited the highest values in all parameters compared to the other extraction methods. Catechins and caffeine were predominantly detected in tea flower extracts through UAE with BG and ethanol (EtOH-UAE). BG-UAE exhibited greater cell viability and cellular antioxidant activity than EtOH-UAE. The researcher expects that this research will contribute to the emergence of a green extraction technique that will offer larger functional components with economic and environmental benefits and minimal chemicals and energy use.

Microwave-Treated Physically Cross-Linked Sodium Alginate and Sodium Carboxymethyl Cellulose Blend Polymer Film for Open Incision Wound Healing in Diabetic Animals-A Novel Perspective for Skin Tissue Regeneration Application

This study aimed at developing the microwave-treated, physically cross-linked polymer blend film, optimizing the microwave treatment time, and testing for physicochemical attributes and wound healing potential in diabetic animals. Microwave-treated and untreated films were prepared by the solution casting method and characterized for various attributes required by a wound healing platform. The optimized formulation was tested for skin regeneration potential in the diabetes-induced open-incision animal model. The results indicated that the optimized polymer film formulation (MB-3) has significantly enhanced physicochemical properties such as high moisture adsorption (154.6 ± 4.23%), decreased the water vapor transmission rate (WVTR) value of (53.0 ± 2.8 g/m²/h) and water vapor permeability (WVP) value (1.74 ± 0.08 g mm/h/m²), delayed erosion (18.69 ± 4.74%), high water uptake, smooth and homogenous surface morphology, higher tensile strength (56.84 ± 1.19 MPa), and increased glass transition temperature and enthalpy (through polymer hydrophilic functional groups depicting efficient cross-linking). The in vivo data on day 16 of post-wounding indicated that the wound healing occurred faster with significantly increased percent re-epithelialization and enhanced collagen deposition with optimized MB-3 film application compared with the untreated group. The study concluded that the microwave-treated polymer blend films have sufficiently enhanced physical properties, making them an effective candidate for ameliorating the diabetic wound healing process and hastening skin tissue regeneration.

Synthesis and characterization of a novel hydrogel based on carboxymethyl chitosan/sodium alginate with the ability to release simvastatin for chronic wound healing

Since wound dressing has been considered a promising strategy to improve wound healing, recent attention has been focused on the development of modern wound dressings based on synthetic and bioactive polymers. In this study, we prepared a multifunctional wound dressing based on carboxymethyl chitosan (CMC)/sodium alginate (Alg) hydrogel containing a nanostructured lipid carrier (NLC) in which simvastatin (SIM) has been encapsulated. This dressing aimed to act as a barrier against pathogens, eliminate excess exudates, and accelerate wound healing. Among various fabricated composites of dressing, the hydrogel composite with a CMC/sodium Alg ratio of 1:2 had an average pore size of about 98.44 ± 26.9 μm and showed 707 ± 31.9% swelling and a 2116 ± 79.2 g m-2per day water vapor transfer rate (WVTR), demonstrating appropriate properties for absorbing exudates and maintaining wound moisture. The NLC with optimum composition and properties had a spherical shape and uniform particle size distribution (74.46 ± 7.9 nm). The prepared nanocomposite hydrogel displayed excellent antibacterial activity againstEscherichia coliandStaphylococcus aureusas well as high biocompatibility on L929 mouse fibroblast cells. It can release the loaded SIM drug slowly and over a prolonged period of time. The highest drug release occurred (80%) within 14 d. The results showed that this novel nanocomposite could be a promising candidate as a wound dressing for treating various chronic wounds in skin tissues.

Construction of Smart Biomaterials for Promoting Diabetic Wound Healing

Diabetes mellitus is a complicated metabolic disease that has become one of the fastest-growing health crises in modern society. Diabetic patients may suffer from various complications, and diabetic foot is one of them. It can lead to increased rates of lower-extremity amputation and mortality, even seriously threatening the life and health of patients. Because its healing process is affected by various factors, its management and treatment are very challenging. To address these problems, smart biomaterials have been developed to expedite diabetic wound closure and improve treatment outcomes. This review begins with a discussion of the basic mechanisms of wound recovery and the limitations of current dressings used for diabetic wound healing. Then, the categories and characteristics of the smart biomaterial scaffolds, which can be utilized as a delivery system for drugs with anti-inflammatory activity, bioactive agency, and antibacterial nanoparticles for diabetic wound treatment were described. In addition, it can act as a responsive system to the stimulus of the pH, reactive oxygen species, and glucose concentration from the wound microenvironment. These results show that smart biomaterials have an enormous perspective for the treatment of diabetic wounds in all stages of healing. Finally, the advantages of the construction of smart biomaterials are summarized, and possible new strategies for the clinical management of diabetic wounds are proposed.

Basella alba stem extract integrated poly (vinyl alcohol)/chitosan composite films: A promising bio-material for wound healing

Natural extract-based bio-composite material for wound healing is gaining much attention due to risk of infection and high cost of commercial wound dressing film causes serious problem on the human well-being. Herein, the study outlines the preparation of Poly (vinyl alcohol)/Chitosan/Basella alba stem extract (BAE) based bio-composite film through solvent casting technique and well characterized for wound healing application. Incorporation of BAE into Poly (vinyl alcohol)/Chitosan matrix has shown existence of secondary interactions confirmed by FT-IR analysis. Good morphology, thermal stability and significant improvement in flexibility (∼63.38 %) of the films were confirmed by SEM, TGA and Mechanical test results, respectively. Hydrophilic property (∼9.04 %), water vapor transmission rate (∼70.07 %), swelling ability (∼14.7 %) and degradation rate (∼14.04 %) were enhanced with increase in BAE content. In-vitro studies have shown good antibacterial activity against foremost infectious bacterial strains S. aureus and E. coli. Additionally, BAE integrated Poly (vinyl alcohol)/Chitosan film has amplified anti-inflammatory (∼79.38 %) property, hemocompatibility and excellent biocompatibility (94.9 %) was displayed by cytotoxicity results. Moreover, in-vitro scratch assay and cell adhesion test results illustrated prominent wound healing (96.5 %) and adhesion. Overall results of the present work proclaim that developed bio-composite film could be utilized as a biomaterial in wound care applications.

Alginates Combined with Natural Polymers as Valuable Drug Delivery Platforms

Alginates (ALG) have been used in biomedical and pharmaceutical technologies for decades. ALG are natural polymers occurring in brown algae and feature multiple advantages, including biocompatibility, low toxicity and mucoadhesiveness. Moreover, ALG demonstrate biological activities per se, including anti-hyperlipidemic, antimicrobial, anti-reflux, immunomodulatory or anti-inflammatory activities. ALG are characterized by gelling ability, one of the most frequently utilized properties in the drug form design. ALG have numerous applications in pharmaceutical technology that include micro- and nanoparticles, tablets, mucoadhesive dosage forms, wound dressings and films. However, there are some shortcomings, which impede the development of modified-release dosage forms or formulations with adequate mechanical strength based on pure ALG. Other natural polymers combined with ALG create great potential as drug carriers, improving limitations of ALG matrices. Therefore, in this paper, ALG blends with pectins, chitosan, gelatin, and carrageenans were critically reviewed.

Biomaterials for Tissue Engineering Applications and Current Updates in the Field: A Comprehensive Review

Tissue engineering has emerged as an interesting field nowadays; it focuses on accelerating the auto-healing mechanism of tissues rather than organ transplantation. It involves implanting an In Vitro cultured initiative tissue or a scaffold loaded with tissue regenerating ingredients at the damaged area. Both techniques are based on the use of biodegradable, biocompatible polymers as scaffolding materials which are either derived from natural (e.g. alginates, celluloses, and zein) or synthetic sources (e.g. PLGA, PCL, and PLA). This review discusses in detail the recent applications of different biomaterials in tissue engineering highlighting the targeted tissues besides the in vitro and in vivo key findings. As well, smart biomaterials (e.g. chitosan) are fascinating candidates in the field as they are capable of elucidating a chemical or physical transformation as response to external stimuli (e.g. temperature, pH, magnetic or electric fields). Recent trends in tissue engineering are summarized in this review highlighting the use of stem cells, 3D printing techniques, and the most recent 4D printing approach which relies on the use of smart biomaterials to produce a dynamic scaffold resembling the natural tissue. Furthermore, the application of advanced tissue engineering techniques provides hope for the researchers to recognize COVID-19/host interaction, also, it presents a promising solution to rejuvenate the destroyed lung tissues.

Recent advances on biomedical applications of pectin-containing biomaterials

There is a growing demand for biomaterials developing with novel properties for biomedical applications hence, hydrogels with 3D crosslinked polymeric structures obtained from natural polymers have been deeply inspected in this field. Pectin a unique biopolymer found in the cell walls of fruits and vegetables is extensively used in the pharmaceutical, food, and textile industries due to its ability to form a thick gel-like solution. Considering biocompatibility, biodegradability, easy gelling capability, and facile manipulation of pectin-based biomaterials; they have been thoroughly investigated for various potential biomedical applications including drug delivery, wound healing, tissue engineering, creation of implantable devices, and skin-care products.

Investigation of Hydrogel Sheets Based on Highly Esterified Pectin

The report describes the features of physical and mechanical properties and absorption capacity of hydrogels based on highly esterified pectin. Experimental data showed the correlation between these values. Also, an attempt is made to explain the obtained dependencies via the hydrogel morphology and the mechanism of its formation.

Bioactive and multifunctional keratin-pullulan based hydrogel membranes facilitate re-epithelization in diabetic model

Hydrogel membrane dressings with multifunctional tunable properties encompassing biocompatibility, anti-bacterial, oxygen permeability, and adequate mechanical strength are highly preferred for wound healing. The present study aimed to develop biopolymer-based hydrogel membranes for the controlled release of therapeutic agent at the wound site. Toward this end we developed Cefotaxime sodium (CTX) loaded keratin (KR)-pullulan (PL) based hydrogel membrane dressings. All membranes show optimized vapor transmission rate (≥1000 g/ m²/day), oxygen permeability >8.2 mg/mL, MTT confirmed good biocompatibility and sufficient tensile strength (17.53 ± 1.9) for being used as a wound dressing. Nonetheless, KR-PL-PVA membranes show controlled CTX release due to enriched hydrophilic moieties which protect the wound from getting infected. In vivo results depict that CTX-KR-PL-PVA membrane group shows a rapid wound closure rate (p < 0.05) with appreciable angiogenesis, accelerated re-epithelization, and excessive collagen deposition at the wound site. These results endorsed that CTX-KR-PL-PVA hydrogel membranes are potential candidates for being used as dressing material in the diabetic wound.

Tailoring of Geranium Oil-Based Nanoemulsion Loaded with Pravastatin as a Nanoplatform for Wound Healing

The healing of a burn wound is a complex process that includes the re-formation of injured tissues and the control of infection to minimize discomfort, scarring, and inconvenience. The current investigation’s objective was to develop and optimize a geranium oil–based self-nanoemulsifying drug delivery system loaded with pravastatin (Gr-PV-NE). The geranium oil and pravastatin were both used due to their valuable anti-inflammatory and antibacterial activities. The Box–Behnken design was chosen for the development and optimization of the Gr-PV-NE. The fabricated formulations were assessed for their droplet size and their effects on the burn wound diameter in experimental animals. Further, the optimal formulation was examined for its wound healing properties, antimicrobial activities, and ex-vivo permeation characteristics. The produced nanoemulsion had a droplet size of 61 to 138 nm. The experimental design affirmed the important synergistic influence of the geranium oil and pravastatin for the healing of burn wounds; it showed enhanced wound closure and improved anti-inflammatory and antimicrobial actions. The optimal formulation led to a 4-fold decrease in the mean burn wound diameter, a 3.81-fold lowering of the interleukin-6 serum level compared to negative control, a 4-fold increase in the inhibition zone against Staphylococcus aureus compared to NE with Gr oil, and a 7.6-fold increase in the skin permeation of pravastatin compared to PV dispersion. Therefore, the devised nanoemulsions containing the combination of geranium oil and pravastatin could be considered a fruitful paradigm for the treatment of severe burn wounds.

Arabinoxylan-Carboxymethylcellulose Composite Films for Antibiotic Delivery to Infected Wounds

Modern dressings should provide for local delivery of antibiotics and protect the wound from bacterial infection, dehydration and environmental factors to achieve optimal healing. The local delivery of antibiotics can reduce adverse effects and resistance challenges. In this study, we fabricated film dressings composed of arabinoxylan (AX) from Plantago ovata seed husks and carboxymethylcellulose (CMC) by a solvent cast method for the delivery of the antibiotic amikacin (AMK). To determine the suitability of the prepared AX-CMC composite films as wound dressings and drug delivery materials, their physical, chemical, mechanical, morphological, thermal, pharmaceutical, antimicrobial, cytocompatible, and drug delivery properties were investigated. The results demonstrated that the dressings were suitable for delivering the drug at the wound site in a sustained manner and keeping the environment moist for rapid healing. The AMK-loaded AX-CMC films exhibited controlled release of AMK, excellent antibacterial activity, and cytocompatibility. Thus, the AX-CMC composite films appear to be promising bioactive dressing materials for the prevention of wound infections.

Development and Characterization of Gentamicin-Loaded Arabinoxylan-Sodium Alginate Films as Antibacterial Wound Dressing

Biopolymer-based antibacterial films are attractive materials for wound dressing application because they possess chemical, mechanical, exudate absorption, drug delivery, antibacterial, and biocompatible properties required to support wound healing. Herein, we fabricated and characterized films composed of arabinoxylan (AX) and sodium alginate (SA) loaded with gentamicin sulfate (GS) for application as a wound dressing. The FTIR, XRD, and thermal analyses show that AX, SA, and GS interacted through hydrogen bonding and were thermally stable. The AXSA film displays desirable wound dressing characteristics: transparency, uniform thickness, smooth surface morphology, tensile strength similar to human skin, mild water/exudate uptake capacity, water transmission rate suitable for wound dressing, and excellent cytocompatibility. In Franz diffusion release studies, >80% GS was released from AXSA films in two phases in 24 h following the Fickian diffusion mechanism. In disk diffusion assay, the AXSA films demonstrated excellent antibacterial effect against E.coli, S. aureus, and P. aeruginosa. Overall, the findings suggest that GS-loaded AXSA films hold potential for further development as antibacterial wound dressing material.