Formation and speciation of haloacetamides and haloacetonitriles for chlorination, chloramination, and chlorination followed by chloramination

Comparative investigation of known and unknown disinfection by-product precursor removal and microbial community from biological biochar and activated carbon filters

Biological activated carbon filter (BAC) is one of the most effective technologies for removing disinfection by-product (DBP) precursors from water. Biochar is a lower-cost medium that has the potential to replace granular activated carbon in BAC applications, thus leading to the development of biological biochar filter (BCF). This study compared BCF with BAC for the removal of DBP precursors using column experiments. Both BCF and BAC achieved the removal of DBP precursors, resulting in concentrations of all DBP formation potential below the World Health Organization guideline values for drinking water. Bromodichloromethane and unknown DBP precursor removal by BCF was comparable to that by BAC. However, BAC removed more chloroform and dichloroacetontrile precursors than BCF. For microbial community analysis, cell numbers in a bottom layer (inlet) of BCF and BAC columns were higher than those in the top layer. The abundances of Nordella and a microbial genus from Burkholderiaceae at the bottom layer showed a strong correlation to the number of DBP precursors removed and were comparable in BCF and BAC. This finding likely contributes to the similarities between DBPs species removed and the removal performances of some known and unknown DBP precursors by BCF and BAC. Overall results from this study revealed that biochar can be served as a low-cost and sustainable replacement of activated carbon in water filter for DBP precursor removal.

Effect of UV/peroxymonosulfate pretreatment on disinfection byproduct (DBP) formation during post-chlorination of humic acid

UV/peroxymonosulfate (UV/PMS) is a promising advanced oxidation technology in water treatment. This study aimed to investigate the impact of UV/PMS on humic acid (HA) and the influence of PMS dosage, pretreatment time, pH pretreatment, nitrate, nitrite, ammonium, and bicarbonate influencing factors on disinfection byproduct (DBP) formation during post-chlorination. With increased PMS dosage or pretreatment time, the UV/PMS treatment significantly reduced ultraviolet absorbance and increased mineralization. It altered the fractional constituent as humic substances were gradually transformed into building blocks and low-molecular-weight acids. However, most DBP formation increased initially and then decreased after subsequent chlorination. Rising nitrate or nitrite concentrations markedly promoted halonitromethane (HNM) formation. The presence of ammonia had a more significant impact on dichloroacetonitrile (DCAN) formation. Bicarbonate in UV/PMS pretreatment increased carbonated disinfection byproduct (C-DBP) formation, whereas it had a negligible impact on nitrogenous disinfection byproduct (N-DBP) formation. The present study revealed the impact of a series of influencing factors on DBP formation in UV/PMS reaction systems, providing comprehensive insights on applying UV/PMS in actual practice.

Effects of alternative disinfection methods on the characteristics of effluent organic matter and the formation of disinfection byproducts

The characteristics of effluent organic matter (EfOM) and the type of disinfection methods are closely related to the formation of disinfection byproducts (DBPs) in reclaimed water. In this study, five disinfection methods, i.e., chlorination, ultraviolet (UV) followed by chlorination (UV + Cl), UV/chlorine (UV/Cl), chloramination, and chlorine dioxide (ClO2), were applied to investigate the changes in the properties of EfOM, the formation of DBPs, and the relationship between EfOM properties and DBP formation during the disinfection of four secondary biological effluents. The results showed that EfOM with medium molecular weight (MW) (0.5-6 kDa) was the dominant fraction for all WWTPs. From a fluorescence perspective, the EfOM of the AAO process was rich in humic matter, while the EfOM of the oxidation ditch (OD) process was rich in protein matter. Disinfectants tended to transfer EfOM with high molecular weight (MW) (>6 kDa) to those with low MW (<0.5 kDa). Chlorination, UV + Cl and UV/Cl were more reactive to humic matter, while chloramination and chlorine dioxide were more reactive to protein matter. The formation of known DBPs was mainly dependent on humic matter, while protein matter was more likely to generate unknown DBPs. N-DBPs only accounted for 5.7%-17.7% of the total DBPs, but contributed more than 70% of the calculated toxicity, among which bromochloroacetonitrile (BCAN), dichloroacetonitrile (DCAN), and monobromoacetamide (MBAcAm) were the most important contributors to the calculated cytotoxicity. Monobromoacetic acid (MBAA) and MBAcAm were the primary drivers of the calculated genotoxicity. Overall, UV + Cl was the suggested optimal disinfection method for WWTPs.

Insights into C-C Bond Cleavage Mechanisms in Dichloroacetonitrile Formation during Chlorination of Long-Chain Primary Amines, Amino Acids, and Dipeptides

Dichloroacetonitrile (DCAN) as one of the potentially prioritized regulated DBPs has drawn great attention; however, understanding its formation, especially the C-C bond cleavage mechanisms, is limited. In this study, DCAN formation mechanisms from long-chain primary amines, amino acids, and dipeptides during chlorination were investigated by a combined computational and experimental approach. The results indicate that nitriles initially generate for all of the above precursors, then they undergo β-C-hydroxylation or/and α-C-chlorination processes, and finally, DCAN is produced through the Cα-Cβ bond cleavage. For the first time, the underlying mechanism of the C-C bond cleavage was unraveled to be electron transfer from the O- anion into its attached C atom in the chlorinated nitriles, leading to the strongly polarized Cα-Cβ bond heterocleavage and DCAN- formation. Moreover, DCAN molar yields of precursors studied in the present work were found to be determined by their groups at the γ-site of the amino group, where the carbonyl group including -CO2-, -COR, and -CONHR, the aromatic group, and the -OH group can all dramatically facilitate DCAN formation by skipping over or promoting the time-consuming β-C-hydroxylation process and featuring relatively lower activation free energies in the C-C bond cleavage. Importantly, 4-amino-2-hydroxybutyric acid was revealed to possess the highest DCAN yield among all the known aliphatic long-chain precursors to date during chlorination. Additionally, enonitriles, (chloro-)isocyanates, and nitriles can be generated during DCAN formation and should be of concern due to their high toxicities.

Formation characteristics and acute toxicity assessment of THMs and HAcAms from DOM and its different fractions in source water during chlorination and chloramination

The formation characteristics of trihalomethanes (THMs) and haloacetamides (HAcAms) from dissolved organic matter and its fractions were investigated during chlorine-based disinfection processes. The relationships between water quality parameters, fluorescence parameters, and the formation levels of THMs and HAcAms were analyzed. The fractions contributing most to the acute toxicity were identified. The trichloromethane (TCM) generation level (72 h) generally followed the order of Cl₂ > NH₂Cl > NHCl₂ process. The NHCl₂ process was superior to the NH₂Cl process in controlling TCM formation. Hydrophobic acidic substance (HOA), hydrophobic neutral substance (HON), and hydrophilic substance (HIS) were identified as primary precursors of 2,2-dichloroacetamide and trichloroacetamide during chlorination and chloramination. The formation of TCM mainly resulted from HOA, HON and HIS fractions relatively uniformly, while HOA and HIS fractions contributed more to the formation of bromodichloromethane and dibromomonochloromethane. UV₂₅₄ could be used as an alternative indicator for the amount of ΣTHMs formed during chlorination and chloramination processes. Dissolved organic nitrogen was a potential precursor of 2,2-dichloroacetamide during chlorination process. The fractions with the highest potential acute toxicity after the chlorination were water-dependent.

The effect of metformin and drinking water quality variation on haloacetamide formation during chlor(am)ination of acetaminophen

Acetaminophen (Apap) is widely used and is known to form toxic haloacetamides (HAcAms) during chlorination. Metformin (Met) is a typical medication with usage much higher than that of Apap and its ubiquitous presence in the environment is known. The objective of this study was to investigate the effects of Met which contains multiple amino groups potentially joining reactions and different chlorination methods on HAcAm formation from Apap. In addition, a major drinking water treatment plant (DWTP) using the largest river in southern Taiwan was sampled to study the influence of Apap in a DWTP on the HAcAm formation. Results showed increasing dichloroacetamide (DCAcAm) molar yields of Apap at a Cl/Apap molar ratio of 5 during chlorination (0.15%) and two-step chlorination (0.03%). HAcAms were formed by the chlorine substitution of hydrogen on the methyl group in Apap followed by the cleavage of the bonding between nitrogen and aromatic. While a high Cl/Apap ratio during chlorination led to reactions between chlorine and HAcAms formed decreasing the HAcAm yields, the two-step chlorination further reduced the HAcAm formation during chlorination by a factor of 1.8-8.2. However, Met which limitedly formed HAcAms increased the DCAcAm yields of Apap by 228% at high chlorine dosages during chlorination and by 244% during two-step chlorination. In the DWTP, trichloroacetamide (TCAcAm) formation was important. The formation was positively correlated with NH₄⁺, dissolved organic carbon (DOC), and specific ultraviolet absorbance (SUVA). DCAcAm dominated in the presence of Apap. The DCAcAm molar yields were 0.17%-0.27% and 0.08%-0.21% in the wet and dry seasons, respectively. The HAcAm yields of Apap in the DWTP were limitedly changed between different locations and seasons. Apap could be one important cause for HAcAm formation in a DWTP, as the presence of other pharmaceuticals such as Met possibly worsens the situation in chlorine applications.

Permanganate preoxidation affects the formation of disinfection byproducts from algal organic matter

During harmful algal blooms (HABs), permanganate may be used as a preoxidant to improve drinking water quality by removing algal cells and degrading algal toxins. However, permanganate also lyses algal cells, releasing intracellular algal organic matter (AOM). AOM further reacts with permanganate to alter the abundance of disinfection byproduct (DBP) precursors, which in turn affects DBP formation during disinfection. In this study, we evaluated the impacts of preoxidation by permanganate applied at commonly used doses (i.e., 1-5 mg/L) on DBP generation during chlorination and chloramination of AOM. We found that permanganate preoxidation increased trichloronitromethane (TCNM) formation by up to 3-fold and decreased dichloroacetonitrile (DCAN) formation by up to 40% during chlorination, indicating that permanganate oxidized organic amines in AOM to organic nitro compounds rather than organic nitrile compounds. To test this proposed mechanism, we demonstrated that permanganate oxidized organic amines in known DBP precursors (i.e., tyrosine, tryptophan) to favor the production of TCNM over DCAN during chlorination. Compared to the decreased formation of DCAN during chlorination, permanganate increased DCAN formation by 30-50% during chloramination of AOM. This difference likely arose from monochloramine's ability to react with non-nitrogenous precursors (e.g., organic aldehydes) that formed during permanganate preoxidation of AOM to generate nitrogen-containing intermediates that go on to form DCAN. Our results also showed that permanganate preoxidation favored the formation of dichlorobromomethane (DCBM) over trichloromethane (TCM) during chlorination and chloramination. The increased formation of DBPs, especially nitrogenous DBPs that are more toxic than carbonaceous DBPs, may increase the overall toxicity in finished drinking water when permanganate preoxidation is implemented.

NRF2-ARE signaling is responsive to haloacetonitrile-induced oxidative stress in human keratinocytes

Humans are exposed to disinfection by-products through oral, inhalation, and dermal routes, during bathing and swimming, potentially causing skin lesions, asthma, and bladder cancer. Nuclear factor E2-related factor 2 (NRF2) is a master regulator of the adaptive antioxidant response via the antioxidant reaction elements (ARE) orchestrating the transcription of a large group of antioxidant and detoxification genes. Here we used an immortalized human keratinocyte model HaCaT cells to investigate NRF2-ARE as a responder and protector in the acute cytotoxicity of seven haloacetonitriles (HANs), including chloroacetonitrile (CAN), bromoacetonitrile (BAN), iodoacetonitrile (IAN), bromochloroacetonitrile (BCAN), dichloroacetonitrile (DCAN), dibromoacetonitrile (DBAN), and trichloroacetonitrile (TCAN) found in drinking water and swimming pools. The rank order of cytotoxicity among the HANs tested was IAN ≈ BAN ˃ DBAN ˃ BCAN ˃ CAN ˃ TCAN ˃ DCAN based on their LC₅₀. The HANs induced intracellular reactive oxygen species accumulation and activated cellular antioxidant responses in concentration- and time-dependent fashions, showing elevated NRF2 protein levels and ARE activity, induction of antioxidant genes, and increased glutathione levels. Additionally, knockdown of NRF2 by lentiviral shRNAs sensitized the HaCaT cells to HANs-induced cytotoxicity, emphasizing a protective role of NRF2 against the cytotoxicity of HANs. These results indicate that HANs cause oxidative stress and activate NRF2-ARE-mediated antioxidant response, which in turn protects the cells from HANs-induced cytotoxicity, highlighting that NRF2-ARE activity could be a sensitive indicator to identify and characterize the oxidative stress induced by HANs and other environmental pollutants.

Formation of regulated and unregulated disinfection byproducts during chlorination and chloramination: Roles of dissolved organic matter type, bromide, and iodide

Algal blooms and wastewater effluents can introduce algal organic matter (AOM) and effluent organic matter (EfOM) into surface waters, respectively. In this study, the impact of bromide and iodide on the formation of halogenated disinfection byproducts (DBPs) during chlorination and chloramination from various types of dissolved organic matter (DOM, e.g., natural organic matter (NOM), AOM, and EfOM) were investigated based on the data collected from literature. In general, higher formation of trihalomethanes (THMs) and haloacetic acids (HAAs) was observed in NOM than AOM and EfOM, indicating high reactivities of phenolic moieties with both chlorine and monochloramine. The formation of haloacetaldehydes (HALs), haloacetonitriles (HANs) and haloacetamides (HAMs) was much lower than THMs and HAAs. Increasing initial bromide concentrations increased the formation of THMs, HAAs, HANs, and HAMs, but not HALs. Bromine substitution factor (BSF) values of DBPs formed in chlorination decreased as specific ultraviolet absorbance (SUVA) increased. AOM favored the formation of iodinated THMs (I-THMs) during chloramination using preformed chloramines and chlorination-chloramination processes. Increasing prechlorination time can reduce the I-THM concentrations because of the conversion of iodide to iodate, but this increased the formation of chlorinated and brominated DBPs. In an analogous way, iodine substitution factor (ISF) values of I-THMs formed in chloramination decreased as SUVA values of DOM increased. Compared to chlorination, the formation of noniodinated DBPs is low in chloramination.

Characterization of dissolved organic carbon and disinfection by-products in biochar filter leachate using orbitrap mass spectrometry

Biochar is a low-cost adsorbent with considerable potential for utilization as a water filtration medium; however, organic matter leaching from biochar can lead to the formation of disinfection by-products (DBPs). This study investigated the leaching of dissolved organic carbon (DOC) from eucalyptus-derived biochar and the formation of DBPs generated by chlorination and chloramination. Column experiments with empty bed contact times (EBCTs) of 10 and 30 min were conducted for 200 bed volumes (BVs). The highest DOC concentration (3.5 µg-C/g-biochar) was detected with an EBCT of 30 min. Chloroform (49 µg/L) and dichloroacetonitrile (7 µg/L) because of chlorination were found during the first five BVs, but were reduced thereafter. During the first 10 BVs, unknown chlorinated DBPs generated (CHOCl) by chlorination and chloramination (193 and 152 formulae, respectively) were tentatively identified via an unknown screening analysis. The release of DBP precursors from biochar tentatively identified in this study will impact water filtration applications.

Effect of silver nanoparticles and chlorine reaction time on the regulated and emerging disinfection by-products formation

Silver nanoparticles (AgNPs) are used in many industries for multiple applications that inevitably release AgNPs into surface water sources. The formation kinetics of disinfection by-products (DBPs) in the presence of AgNPs was investigated during chlorination. Experiments were carried out with raw water from a canal in Songkhla, Thailand, which analyzed the formation potential (FP) of trihalomethanes FP (THMFP), iodo-trihalomethanes FP (I-THMFP), haloacetonitriles FP (HANFP), and trichloronitromethane FP. Increased AgNP concentrations by 10-20 mg/L led to a higher specific formation rate of chloroform which is described by zero- and first-order kinetics. The increase in the specific formation of chloroform as increasing chlorine contact time could enhance both the THMFP rates and the maximum THMFP concentrations in all tested AgNPs. The AgNP content did not have a significant influence on I-THMFP and HANFP concentrations or speciation. The I-THMFP and HANFP increased in a short-chlorination time as mostly complete formation <12 h, and then the rate decreased as the reaction proceeded. The levels of THMs and many emerging DBPs are related to the presence of AgNPs in chlorinated water and chlorine reaction time. THMFP had a higher impact on integrated toxic risk value (ITRV) than I-THMFP and HANFP because of the chlorination of water with AgNPs. The chlorine reaction time was more effective for increasing the ITRV of THMFP than the level of AgNPs. Water treatment plants should control the DBPs that cause possible health risks from water consumption by optimizing water distribution time.

Disinfection by-product (DBP) research in China: Are we on the track?

Disinfection by-products (DBPs) formed during water disinfection has drawn significant public concern due to its toxicity. Since the first discovery of the trihalomethanes in 1974, continued effort has been devoted on DBPs worldwide to investigate the formation mechanism, levels, toxicity and control measures in drinking water. This review summarizes the main achievements on DBP research in China, which included: (1) the investigation of known DBP occurrence in drinking water of China; (2) the enhanced removal of DBP precursor by water treatment process; (3) the disinfection optimization to minimize DBP formation; and (4) the identification of unknown DBPs in drinking water. Although the research of DBPs in China cover the whole formation process of DBPs, there is still a challenge in effectively controlling the drinking water quality risk induced by DBPs, an integrated research framework including chemistry, toxicology, engineering, and epidemiology is especially crucial.

Enhanced formation of dichloroacetamide and dichloroacetonitrile during chloramination of drinking water and model organic matters in the presence of copper corrosion products

The formation of nitrogenous disinfection byproducts (N-DBPs) occurs in chloraminated water in drinking water distribution systems and may be affected by metal pipe materials and their corrosion products. The effect of copper corrosion products, including Cu²⁺, CuO, and Cu₂O, on the formation of dichloroacetonitrile (DCAN) and dichloroacetamide (DCAcAm) was investigated during chloramination of natural organic matter (NOM), model precursors (carboxylic acids and amino acids), and real water samples. Copper corrosion products enhanced DCAN and DCAcAm formation during chloramination of NOM by 33%-72% and 11%-80%, respectively. Addition of ¹⁵N-labeled monochloramine showed that the copper corrosion products primarily enhanced the formation of DCAN using organic nitrogen and monochloramine as nitrogen sources, and the formation of DCAcAm using monochloramine as the nitrogen source, but had a limited impact on the formation of DCAcAm using organic nitrogen as the nitrogen source. A distinct N-DBP formation pathway in the presence of Cu²⁺ and CuO was observed using tyrosine as a model compound, which included the formation of 1,4-benzoquinone as a dominant intermediate. On reaction with monochloramine, the 1,4-benzoquinone greatly contributed to enhancement of DCAN and DCAcAm formation using monochloramine as the nitrogen source. During chloramination of real water samples, Cu²⁺ and CuO enhanced DCAN formation by 9-40% and DCAcAm formation by 16-33%. This study increases our knowledge of copper catalyzed DCAN and DCAcAm formation in copper pipes, which will be meaningful for water safety in distribution systems using chloramine disinfection.

DBP formation and toxicity alteration during UV/chlorine treatment of wastewater and the effects of ammonia and bromide

The UV/chlorine process is efficient for the abatement of micropollutants; yet, the formation of disinfection by-products (DBPs) and the toxicity can be altered during the treatment. This study investigated effluent organic matter characterization, DBP formation and toxicity alteration after the UV/chlorine treatment of wastewater; particularly, typical water matrix components in wastewater, namely, ammonia and bromide, were studied. The raw wastewater contained low levels of ammonia (3 µM) and bromide (0.5 µM). The UV/chlorine treatment efficiently eliminated 90 - 94% of fluorescent components. Compared with chlorination alone, a 20 min UV/chlorine treatment increased the formation of trihalomethanes (THMs), haloacetic acids (HAAs), chloral hydrate (CH), haloacetonitriles (HANs), trichloronitromethane (TCNM) and haloacetamides (HAcAms) by 90 - 508%. In post-chlorination after the UV/chlorine treatment, the formation of CH, HANs, TCNM and HAcAms increased by 77 - 274%, whereas the formation of both THMs and HAAs increased slightly by 11%. Meanwhile, the calculated cytotoxicity and genotoxicity of DBPs increased considerably after the UV/chlorine treatment and in post-chlorination, primarily due to the increased formation of HAAs and nitrogenous DBPs (N-DBPs). However, the acute toxicity of the wastewater to Vibrio fischeri and genotoxicity determined by the umu test decreased by 19% and 76%, respectively, after the 20 min UV/chlorine treatment. An additional 200 µM ammonia decreased the formation of all detected DBPs during the UV/chlorine treatment and 24 h post-chlorination, except that TCNM formation increased by 11% during post-chlorination. The acute toxicity of wastewater spiked with 200 µM ammonia was 32% lower than that of raw wastewater after the UV/chlorine treatment, but the genotoxicity was 58% higher. The addition of 1 mg/L bromide to the UV/chlorine process dramatically increased the formation of brominated DBPs and the overall calculated cytotoxicity and genotoxicity of DBPs. However, the acute toxicity and genotoxicity of the wastewater decreased by 7% and 100%, respectively, when bromide was added to the UV/chlorine treatment. This study illuminated that UV/chlorine treatment can decrease acute and geno- toxicities of wastewater efficiently.

ClO2 pre-oxidation impacts the formation and nitrogen origins of dichloroacetonitrile and dichloroacetamide during subsequent chloramination

Chlorine dioxide (ClO₂) can be used as a pre-oxidant when chloramination is performed in water treatment plants. However, the effects of ClO₂ pre-oxidation on the formation of nitrogenous disinfection by-products, such as dichloroacetonitrile (DCAN) and dichloroacetamide (DCAcAm), during chloramination are not well understood. In this study, the effects of ClO₂ pre-oxidation on the formation of DCAN and DCAcAm during chloramination of 28 model compounds and seven real water samples were investigated. The sources of nitrogen for DCAN and DCAcAm formation were investigated using ¹⁵N-labeled monochloramine. ClO₂ pre-oxidation affected DCAN and DCAcAm formation during chloramination of model compounds in different ways. ClO₂ pre-oxidation increased unlabeled and ¹⁵N-labeled DCAN and DCAcAm formation during chloramination of six amino acids and peptides and five indoles and tertiary amines. ClO₂ pre-oxidation decreased DCAN formation but increased DCAcAm formation during chloramination of three hydroxybenzamide compounds, but had the opposite effects for four tetracyclines. ClO₂ pre-oxidation generally decreased DCAN and DCAcAm formation during chloramination of the phenolic compounds that are precursors not containing nitrogen. 2-Aminoacetophenone, formamid-trans-muconic acid, and unsaturated ketones were found to be transformation products of ClO₂ oxidation of 3-methylindole, salicylamide, and resorcinol, respectively. Possible DCAN and DCAcAm formation pathways during chloramination after ClO₂ oxidation were identified. For most of the water samples, ClO₂ pre-oxidation decreased the amounts of DCAN and DCAcAm formed during chloramination by 36%-70% and 11%-59%, respectively. This may have been caused by ClO₂ oxidation destroying phenolic precursors and macromolecular proteins rather than amino acids in the water samples.

The formation of disinfection by-products from the chlorination and chloramination of amides

This study examined the potential of six aliphatic and aromatic amides, commonly found in natural waters or used as chemical aids in water treatment, to act as organic precursors for nine haloacetamides (HAcAms), five haloacetonitriles (HANs), regulated trihalomethanes (THMs) and haloacetic acids (HAAs) upon chlorination and chloramination. The impact of key experimental conditions, representative of drinking water, including pH (7 & 8), retention time (4 & 24 h) and bromide levels (0 & 100 μg/L), on the generation of the target DBPs was investigated. The highest aggregate DBP yields upon chlor(am)ination were reported for the aromatic and hydrophobic hydroxybenzamide; 2.7% ± 0.1% M/M (chlorination) and 1.7% M/M (chloramination). Increased reactivity was observed in aliphatic and hydrophilic compounds, acrylamide (2.5 ± 0.2% M/M) and acetamide (1.3 ± 0.2% M/M), in chlorination and chloramination, respectively. The addition of bromide increased average DBP yields by 50-70%. Relative to chlorination, the application of chloramines reduced DBP formation by 66.5% (without Br^-) and by 46.4% (with Br^-). However, bromine incorporation in HAAs and HAcAms was enhanced following chloramination, of concern due to the higher toxicological potency of brominated compounds.

Effects of Sunlight on the Formation Potential of Dichloroacetonitrile and Bromochloroacetonitrile from Wastewater Effluents

Sunlight plays an important role in transforming effluent organic matter as wastewater effluents travel downstream, but the corresponding effects on the formation of haloacetonitriles (HANs), a group of toxic disinfection byproducts, in wastewater-impacted surface water have not been thoroughly investigated. In this study, we observed that sunlight preferentially attenuated the formation potential of bromochloroacetonitrile (BCAN-FP) over that of dichloroacetonitrile (DCAN-FP) in chlorine- and UV-disinfected secondary effluents. For four effluent samples from different plants, 36 h of irradiation by simulated sunlight removed 28-33% of DCAN-FP and 41-48% of BCAN-FP. Across a larger set of effluent samples (n = 18), 8 h of irradiation (equivalent to 2-3 d of natural sunlight) decreased the calculated cytotoxicity contributed by dihaloacetonitrile-FP in most samples. Similar behavior was observed for a mixture of wastewater and surface water (volume ratio 1:1). For UV-disinfected effluents, the higher the UV dose, the more likely was there a reduction in DCAN-FP and BCAN-FP in the subsequent sunlight irradiation. Experiments with model compounds showed that fulvic acid and UV photoproducts of tryptophan yield excited triplet-state organic matters during sunlight irradiation and play an important role in promoting the attenuation of HAN precursors.

Kinetics of the formation and degradation of carbonaceous and nitrogenous disinfection by-products in Bangkok and Songkhla source waters

The kinetics of the formation and degradation of disinfection by-products (DBPs) in the treated water from the Bangkhen and Hatyai water treatment plants in Thailand were investigated. The DBPs studied included trichloromethane (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), trichloroacetonitrile (TCAN), dichloroacetonitrile (DCAN), bromochloroacetonitrile (BCAN), and trichloronitromethane (TCNM). When the chlorination time was increased, the levels of TCM, BDCM, DBCM, and TCNM increased, while the levels of TCAN, DCAN, and BCAN decreased. The kinetic rates of DBPs' formation were assessed based on the formation and degradation rates, which were best described by first-order kinetics. TCM had the highest formation rate with a range of rate constants from 5.5 × 10^-3 to 7.3 × 10^-3 h^-1. TCAN had the lowest degradation rate with a range of rate constants from 0.6 × 10^-3 to 2.9 × 10^-3 h^-1. Good correlations were observed between chlorination time and DBPs' formation normalized by LC₅₀, lowest cytotoxicity, and lowest genotoxicity. A high formation rate of TCM and a low degradation rate of TCAN normalized by their toxicity were observed. The optimal retention time providing low DBPs' formation together with high DBPs' degradation was determined. The retention time of three days decreased the sum of the DBPs/LC₅₀, DBPs/lowest cytotoxicity, and DBPs/lowest genotoxicity from a retention time of one day by 40-60%, 45-65%, and 25-36%, respectively.

Using UV/H2O2 pre-oxidation combined with an optimised disinfection scenario to control CX3R-type disinfection by-product formation

The effects of UV/H₂O₂ pre-oxidation or disinfection methods on the formation of partial disinfection by-products (DBPs) have been studied previously. This study assessed the effect of UV/H₂O₂ pre-oxidation combined with optimisation of the disinfection method on the formation of six classes of CX₃R-type DBPs, including trihalomethanes (THMs), haloacetic acids (HAAs), haloacetaldehydes (HALs), haloacetonitriles (HANs), halonitromethanes (HNMs), and haloacetamides (HAMs). Experimental results showed that a simulated distribution system (SDS) in-situ chloramination or pre-chlorination followed by chloramination effectively decreased total CX₃R-type DBP formation by 51.1-63.5% compared to SDS chlorination, but little reduction in DBP-associated toxicity was observed. The dominant contributors to the calculated toxicity were HANs and HALs. UV/H₂O₂ pre-oxidation was able to destroy the aromatic and dissolved organic nitrogen components of natural organic matter. As a consequence, THM, HAA, and HAL formations increased by 49.5-55.0%, 47.8-61.9%, and 42.0-67.1%, respectively, whereas HAN, HNM, and HAM formations significantly decreased by 52.1-83.6%, 42.9-87.3%, and 74.1-100.0%. UV/H₂O₂ pre-oxidation increased total CX₃R-type DBP formation, during SDS chlorination, whereas SDS in-situ chloramination or pre-chlorination followed by chloramination of UV/H₂O₂-treated water produced lower total CX₃R-type DBPs than water without UV/H₂O₂ pre-oxidation. Nevertheless, the DBP-associated toxicity of water with UV/H₂O₂ pre-oxidation was substantially lower than the toxicity for water without UV/H₂O₂ pre-oxidation, decreased by 24.1-82.7%. HALs followed by HANs contribute to major toxic potencies in UV/H₂O₂ treated water. The best DBP concentration and DBP-associated toxicity abatement results were achieved for water treated by UV/H₂O₂ coupled with in-situ chloramination treatment.

Research progress of disinfection and disinfection by-products in China

Disinfection is an indispensable water treatment process for killing harmful pathogens and protecting human health. However, the disinfection has caused significant public concern due to the formation of toxic disinfection by-products (DBPs). Lots of studies on disinfection and DBPs have been performed in the world since 1974. Although related studies in China started in 1980s, a great progress has been achieved during the last three decades. Therefore, this review summarized the main achievements on disinfection and DPBs studies in China, which included: (1) the occurrence of DBPs in water of China, (2) the identification and detection methods of DBPs, (3) the formation mechanisms of DBPs during disinfection process, (4) the toxicological effects and epidemiological surveys of DBPs, (5) the control and management countermeasures of DBPs in water disinfection, and (6) the challenges and chances of DBPs studies in future. It is expected that this review would provide useful information and reference for optimizing disinfection process, reducing DBPs formation and protecting human health.

Formation and speciation of chlorinated, brominated, and iodinated haloacetamides in chloraminated iodide-containing waters

Haloacetamides (HAMs), an emerging class of disinfection by-products, have received increasing attention due to their elevated cyto- and genotoxicity. However, only limited information is available regarding the iodinated analogues. This study investigated the formation and speciation of iodinated haloacetamides (I-HAMs) and their chlorinated/brominated analogues during the chloramination of bromide and/or iodide-containing waters and a model compound solution over various time periods. The rapid formation of diiodoacetamide (DIAM) was observed during chloramination of three simulated samples, whereas brominated (Br-HAMs) and chlorinated haloacetamides (Cl-HAMs) increased slowly with increasing reaction time. To further understand the differences in the formation of HAMs containing different halogens, experiments with the model compound asparagine in the presence/absence of iodide were conducted. Moreover, iodine utilisation factors and iodine incorporation factors were observed to increase significantly faster and were substantially higher than those of bromine. This implied that, compared with bromide, iodide has substantially greater potential to be transformed to the corresponding HAMs during chloramination, similar to that of other classes of DBPs. That is, I-HAMs formed faster than the other species investigated, including Cl-HAMs and Br-HAMs, in the early reaction stages (0-3 h). The effect of the bromide/iodide ratio (i.e., constant iodide, increasing bromide) on I-HAM formation was also examined. With increasing bromide/iodide ratio, the formation of Br-HAMs increased and dichloroacetamide decreased, but the formation of DIAM was largely unchanged. This was consistent with the constant level of iodide in spite of the increasing bromide. Chlorine and ammonia are applied separately during chloramination in water treatment, so the effect of pre-chlorination (before adding ammonia) on the formation and speciation of I-HAMs during in situ chloramination was also evaluated. Effective mitigation of DIAM formation with in situ chloramination was achieved, and the efficiency improved with increasing pre-chlorination time, where iodide was oxidised to iodate. The HAM-associated cytotoxicity was calculated to determine the change in toxicity at different reaction times, bromide/iodide ratios, and pre-chlorination times. A similar trend as the formation of I-HAMs was observed, which increased rapidly in the first 3 h, but decreased somewhat subsequently. When the bromide/iodide ratio and pre-chlorination time was increased, the calculated toxicity of the HAMs increased (due to more formation of Br-HAMs and less Cl-HAMs) and decreased (due to less DIAM formation), respectively.

Occurrence of nitrogenous and carbonaceous disinfection byproducts in drinking water distributed in Shenzhen, China

A 12-month sampling program was conducted throughout a drinking water distribution system in Shenzhen and the data from 251 samples provide a comprehensive picture of the spatial and seasonal variability of 17 species disinfection by-products (DBPs) in a city with subtropical monsoon climate. The carbonaceous disinfection by-product (C-DBPs) included four trihalomethanes (THMs), three trihaloacetaldehydes (THAs) and two haloketones (HKs). Their median concentrations over the entire period were 19.9 μg/L, 3.4 μg/L and 1.4 μg/L, respectively. The nitrogenous DBPs (N-DBPs) monitored were four haloacetonitriles (HANs) and four haloacetamides (HAcAms). Their median levels were 2.0 μg/L and 1.5 μg/L, respectively. Low levels of brominated DBP species (bromine substitution factors ≤ 0.5) were observed. The BSF of each DBP class followed the trend: THMs ≈ DHAcAms > DHANs > THAs. All the DBP concentrations showed clear seasonal variations with the highest average concentrations in spring. Correlation analyses showed that the THMs and CH levels in Shenzhen drinking water could be used as statistical indicators of the levels of unregulated N-DBPs (0.4 < r < 0.7, p < 0.5). The results supplement the database of DBP occurrence in drinking water in China, and provide an important reference data set for DBP occurrence in cities with a subtropical monsoon climate around the world.

Transformation of DON in reclaimed water under solar light irradiation leads to decreased haloacetamide formation potential during chloramination

Reclaimed water is usually stored in rivers or lakes before subsequent use. In storage ecosystems, the natural process of solar light irradiation plays a key role in water quality, altering disinfection byproduct formation potential in later use. This study investigated changes in haloacetamide formation potential (HAcAm FP) during subsequent chloramination when reclaimed water was exposed to solar light irradiation. Significant decreases in HAcAm FP were observed for the solar light irradiated reclaimed water, with reductions of 27%-69% for different haloacetamides. Moreover, transformation of dissolved organic nitrogen (DON) to inorganic nitrogen occurred during irradiation. The application of ¹⁵N- labeled monochloramine indicated that the nitrogen source of the decreased HAcAms mainly originated from DON, rather than chloramine. Chloramination of the model compound l-asparagine after irradiation demonstrated that the decreased HAcAms could be attributed to the decrease in DON. After solar light irradiation, the brominated HAcAm FP in the presence of bromide was also reduced, while the bromine incorporation factor remained steady. Overall, this study revealed the contribution of natural processes in controlling HAcAm FP during subsequent chloramination, suggesting solar light irradiation is important to water purification during reclaimed water storage.