Adsorption of heavy metal ions by sodium alginate based adsorbent-a review and new perspectives

Non-phytoremediation and phytoremediation technologies of integrated remediation for water and soil heavy metal pollution: A comprehensive review

Since the 1980s, there has been increasing concern over heavy metal pollution remediation. However, most research focused on the individual remediation technologies for heavy metal pollutants in either soil or water. Considering the potential migration of these pollutants, it is necessary to explore effective integrated remediation technologies for soil and water heavy metals. This review thoroughly examines non-phytoremediation technologies likes physical, chemical, and microbial remediation, as well as green remediation approaches involving terrestrial and aquatic phytoremediation. Non-phytoremediation technologies suffer from disadvantages like high costs, secondary pollution risks, and susceptibility to environmental factors. Conversely, phytoremediation technologies have gained significant attention due to their sustainable and environmentally friendly nature. Enhancements through chelating agents, biochar, microorganisms, and genetic engineering have demonstrated improved phytoremediation remediation efficiency. However, it is essential to address the environmental and ecological risks that may arise from the prolonged utilization of these materials and technologies. Lastly, this paper presents an overview of integrated remediation approaches for addressing heavy metal contamination in groundwater-soil-surface water systems and discusses the reasons for the research gaps and future directions. This paper offers valuable insights for comprehensive solutions to heavy metal pollution in water and soil, promoting integrated remediation and sustainable development.

Adsorption behavior and mechanism of Cu(II) by sodium alginate/carboxymethylcellulose/magnesium hydroxide (SC-MH) hydrogel

In the present work, an environmentally-friendly, reusable hydrogel ball characterized by its great adsorption capacity to Cu(II) was synthesized. The preparation of this hydrogel drew on sodium alginate (SA) and carboxymethyl cellulose (CMC) as primary composition elements. The endeavor brought novelty by ingeniously infusing it with slurry magnesium hydroxide (MH). The factors (pH, SC-MH amount, initial concentration, adsorption time) that are critical to adsorption were also investigated. FTIR, SEM-EDS and XPS were used to reveal the adsorption mechanism of Cu on SC-MH. The results show that the surface of SC-MH is rough, and there are a large number of gully-like structures conducive to adsorption, which are rich in hydroxyl and carboxyl groups. Under the optimum conditions, the maximum adsorption capacity reached 215.68 mg/g. Based on its high R2 value (0.999), the Langmuir model is determined to be the most appropriate for describing the adsorption behavior, indicating monolayer homogeneous adsorption. The kinetic data align well with the pseudo-second-order kinetic model. Furthermore, thermodynamic analysis reveals the adsorption process to be spontaneous and endothermic, as demonstrated by a negative ΔG and positive ΔH (38.8859 KJ/mol). The mechanism involves electrostatic attraction, chelation, Mg(OH)2 adsorption and ion exchange.

Effective removal of Cu(II) from water by three-dimensional composite microspheres based on chitosan/sodium alginate/silicon dioxide: Adsorption performance and mechanism

Chitosan (CS) is commonly used as an adsorbent for removing Cu(II) from water, but it has drawbacks such as solubility in dilute acid, difficulty in recycling in powder form, and short service life. This study utilized sodium alginate (SA) as a gel carrier to encapsulate CS, combined with silicon dioxide (SiO2) to improve mechanical stability. The preparation of CS/SA/SiO2 (SSC1.0) involved physical blending, CaCl2 cross-linking, and freeze-drying. Characterization methods such as SEM-EDS, FTIR, BET, and XRD were used to analyze the structural composition of SSC1.0. The material exhibited a folded surface, porous internal cross-section, nitrogen/oxygen-containing functional groups, and thermal stability in high temperatures and various aqueous environments. The adsorption performance of SSC1.0 on Cu(II) was evaluated under different conditions, showing a maximum adsorption capacity of 47.50 mg/g. The material maintained a removal rate above 70 % after 5 cycles. SSC1.0 also showed the highest removal rate of Cu(II) when applied to mine wastewater treatment. Adsorption modeling indicated that the process was driven by chemical reactions and was spontaneous and heat-absorbing.'

Bioinspired hierarchical and dual-morphology humic-acid/pectin/chitosan composite aerogels for efficient removal of pollutants from wastewater

How to solve the contradiction between the efficiency and adsorption rate of porous materials in adsorbing pollutants has always been one of the focus issues. In this study, the small landscape cypress trees structure like biomimetic of a hierarchical and dual morphology 3D porous HA-based aerogel was designed and synthesized to use humic acid (HA), pectin (PE) and chitosan (CTS) as raw materials, which it was formed by the disorderly overlapping of lamella composed of fiber networks in 3D space. Due to its special microstructure, it can be used like separation membrane, which allowing for rapid adsorption of pollutants in the water while the water flow passes through quick. In general, this work provides a new concept for owning fast adsorption rate and efficient adsorption of porous materials of preparation to use green method.

Novel eco-friendly and easily recoverable bismuth-based materials for capturing and removing polyphenols from water

Olive oil production is one of the most developed Europe's sectors, producing olive oil and undesirable by-products, such as olive mill wastewater (OMWW) and organic waste. OMWW, containing large amounts of compounds (mainly polyphenols, phenols, and tannins), represents a problem. In fact, polyphenols have dual nature: i) antioxidant beneficial properties, useful in many industrial fields, ii) biorefractory character making them harmful in high concentrations. If not properly treated, polyphenols can harm biodiversity, disrupt ecological balance, and degrade water quality, posing risks to both environment and human health. From a circular economy viewpoint, capturing large quantities of polyphenols to reuse and removing their residuals from water is an open challenge. This study proposes, for the first time, a new path beyond the state-of-the-art, combining adsorption and degradation technologies by novel, eco-friendly and easily recoverable bismuth-based materials to capture large amounts of two model polyphenols (gallic acid and 3,4,5-trimethoxybenzoic acid), which are difficult to remove by traditional processes, and photodegrade them under solar light. The coupled process gave rise to collect 98% polyphenols, and to rapidly and effectively photodegrade the remaining portion from water.

Exploring the cationic surfactant adsorption efficiency at concentrations relative to the critical micelle concentration by SA/SiO2 microspheres

Studying the adsorption behavior of cationic surfactants can help to develop more effective strategies to limit their dispersion in the environment. However, there have few studies on the adsorption of cationic surfactants from the perspective of critical micelle concentration (CMC). In this study, with cetyltrimethylammonium bromide (CTAB) and octadecyl trimethylammonium bromide (OTAB) serving as the model cationic surfactants, the effect of CMC on the adsorption behavior of cationic surfactant onto the surface of sodium alginate/silica (SA/SiO2) microspheres was systematically revealed. The adsorption mechanism relative to CMC was investigated under different conditions, including surfactant concentration, pH, temperature, and adsorption time. The results suggest that at identical concentrations, the smaller the CMC value of the cationic surfactants, the greater the adsorption amount (qt). qt for CTAB and OTAB were 583.2 and 678.0 mg/g respectively, with the concentration higher than their CMC value. When the concentration was lower than the CMC value of the cationic surfactants, qt for CTAB and OTAB were 123.2 and 138.7 mg/g, respectively. The CMC value of CTAB was lower than that of OTAB under identical conditions, suggesting that the adsorption of cationic surfactants is related to their CMC. These results are beneficial for the removal of cationic surfactants by adsorption methods.

Advances in Hydrogels Research for Ion Detection and Adsorption

The continuing development of heavy industry worldwide has led to an exponential increase in the amount of wastewater discharged from factories and entering the natural world in the form of rivers and air. As the top of the food chain in the natural world, toxic ions penetrate the human body through the skin, nose, and a few milligrams of toxic ions can often cause irreversible damage to the human body, so ion detection and adsorption is related to the health and safety of human beings. Hydrogel is a hydrophilic three-dimensional reticulated polymer material that first synthesized by Wichterle and Lim in 1960, which is rich in porous structure and has a variety of active adsorption sites as a new type of adsorbent and can be used to detect ions through the introduction of photonic crystals, DNA, fluorescent probe, and other materials. This review describes several synthetic and natural hydrogels for the adsorption and detection of ions and discusses the mechanism of ion adsorption by hydrogels, and provide a perspective for the future development.

Engineered Cyanobacteria-Based Living Materials for Bioremediation of Heavy Metals Both In Vitro and In Vivo

The pollution caused by heavy metals (HMs) represents a global concern due to their serious environmental threat. Photosynthetic cyanobacteria have a natural niche and the ability to remediate HMs such as cadmium. However, their practical application is hindered by a low tolerance to HMs and issues related to recycling. In response to these challenges, this study focuses on the development and evaluation of engineered cyanobacteria-based living materials for HMs bioremediation. Genes encoding phytochelatins (PCSs) and metallothioneins (MTs) were introduced into the model cyanobacterium Synechocystis sp. PCC 6803, creating PM/6803. The strain exhibited improved tolerance to multiple HMs and effectively removed a combination of Cd2+, Zn2+, and Cu2+. Using Cd2+ as a representative, PM/6803 achieved a bioremediation rate of approximately 21 μg of Cd2+/OD750 under the given test conditions. To facilitate its controllable application, PM/6803 was encapsulated using sodium alginate-based hydrogels (PM/6803@SA) to create "living materials" with different shapes. This system was feasible, biocompatible, and effective for removing Cd2+ under simulated conditions of zebrafish and mice models. Briefly, in vitro application of PM/6803@SA efficiently rescued zebrafish from polluted water containing Cd2+, while in vivo use of PM/6803@SA significantly decreased the Cd2+ content in mice bodies and restored their active behavior. The study offers feasible strategies for HMs bioremediation using the interesting biomaterials of engineered cyanobacteria both in vitro and in vivo.

Amputation of Remazol brilliant blue dye on crosslinked chitosan hydrogel: Statistical treatment and experimental evaluation

The primary aim of this research is to comprehensively assess the applicability of chitosan biopolymer towards water treatment application and to enhance its adsorption capacity towards Remazol brilliant blue R-19 dye. This has been achieved through physical modification to obtain the material in hydrogel form and chemical modification by crosslinking it with barbituric acid. The characterization of the resulting Chitosan-barbituric acid hydrogel (CBH) was carried out using various analytical techniques such as SEM-EDX, FT-IR, TGA-DTA, XRD, and BET. CBH was employed as the adsorbent to eliminate R-19 dye from aqueous media. Utilizing response surface methodology (RSM), the parameters were fine-tuned, leading to the achievement of more than a 95% removal for R-19 dye. The adsorption behavior closely adhered to the Langmuir isotherm and pseudo-second-order kinetics. An interesting observation indicated that the rise in temperature leads to rise in adsorption capacity of CBH. The maximum adsorption capacities evaluated at 301.15 K, 313.15 K, 318.15 K, and 323.15 K were 566.6 mg g-1, 624.7 mg g-1, 671.3 mg g-1, and 713.5 mg g-1 respectively, in accordance with the Langmuir isotherm model. Examining the thermodynamics of the adsorption process revealed its spontaneous nature (ΔG = -21.14 to -27.09 kJ mol-1) across the entire temperature range. Furthermore, the assessment of the isosteric heat of adsorption (ΔHads) was conducted using the Clausius-Clapeyron equation, with results indicating an increase in ΔHads from 1.85 to 2.16 kJ mol-1 with temperature rise from 301.15 K to 323.15 K due to augmented surface loading. This suggested the existence of lateral interactions between the adsorbed dye molecules. The potential of adsorbent for regeneration was investigated, demonstrating the ability to reuse the material. Sustainability parameter calculated for synthesis process reflected a notably low E-factor value of 0.32 demonstrated the synthesis is environment friendly.

Recyclable chitosan adsorbent: Facile functionalization strategy, excellent removal capacity of dyes and adsorption mechanism

The development of chitosan-based adsorbents with facile preparation, high adsorption performance and reusability for the removal of contaminant dyes remains a persistent challenge. To overcome this challenge, herein, we have developed a novel and extremely facile one-step strategy by which a new high-performance chitosan/polyethyleneimine/polyethylene glycol diglycidyl ether adsorbent (named as CC/PEI/PGDE) has been successfully fabricated via direct functionalization of CC by PEI at ambient temperature followed by subsequent freeze-drying. The Box-Behnken Design was employed to optimize the concentrations of adsorbent components. Attractively, this adsorbent exhibit outstanding adsorption performances to congo red (RED), acid blue-25 (BLUE) and amino black-10B (BLACK) with 2901 mg g-1 (90.9 %), 3434 mg g-1 (90.9 %), and 1438 mg g-1 (90.1 %) of adsorption capacities (removal efficiencies), respectively, and maintains nearly the same adsorption behaviors to original adsorbent even after 6 cycles of adsorption-desorption processes. Meanwhile, three kinetic models, three isothermal models, and the Vant Hoff model are employed to further investigate the adsorption behaviors of RED, BLUE, and BLACK dyes by CC/PEI/PGDE. The results from SEM, EDS, BET, FT-IR, pHZPC and XPS confirm that hydrogen bond interactions and electrostatic attractions play crucial roles in facilitating dyes adsorption by CC/PEI/PGDE. It is expected that this work can bring forward a new perspective for the facile design of high-performance adsorbent for removing anionic dyes from wastewater.

Rapidly reducing cadmium from contaminated farmland soil by novel magnetic recyclable Fe3O4/mercapto-functionalized attapulgite beads

Reducing cadmium (Cd) content from contaminated farmland soils remains a major challenge due to the difficulty in separating commonly used adsorbents from soils. This study synthesized novel millimeter-sized magnetic Fe3O4/mercapto-functionalized attapulgite beads (MFBs) through a facile one-step gelation process incorporating alginate. The MFBs inherit the environmental stability of alginate and enhance its mechanical strength by hybridizing Fe3O4 and clay mineral components. MFBs can be easily separated from flooded soils by magnets. When applied to 12 Cd-polluted paddy soils and 14 Cd-polluted upland soils, MFBs achieved Cd(II) removal rates ranging from 16.9% to 62.2% and 9.8%-54.6%, respectively, within a 12-h period. The MFBs predominantly targeted the exchangeable and acid soluble, and reducible fractions of Cd, with significantly enhanced removal efficiencies in paddy soils compared to upland soils. Notably, MFBs exhibited superior adsorption performance in soils with lower pH and organic matter (OM) content, where the bioavailability and mobility of Cd are heightened. The reduction of Cd content by MFBs is a sustainable and safe method, as it permanently removes the bioavailable Cd from soil, rather than temporarily reducing its bioavailability. The functional groups such as -SH, -OH, present in attapulgite and alginate of MFBs, played a crucial role in Cd(II) adsorption. Additionally, attapulgite and zeolite provided a porous matrix structure that further enhanced Cd(II) adsorption. The results of X-ray photoelectron spectroscopy suggested that both chemical precipitation and surface complexation contributed to Cd(II) removal. The MFBs maintained 87.6% Cd removal efficiency after 5 regeneration cycles. The surface of the MFBs exposed new adsorption sites and increased the specific surface area during multiple cycles with Cd-contaminated soil. This suggests that MFBs treatment with magnetic retrieval is a potentially effective pathway for the rapid removal of Cd from contaminated farmland soils.

Unveiling the biointerfaces characteristics and removal pathways of Cr(Ⅵ) in Bacillus cereus FNXJ1-2-3 for the Cr(Ⅵ)-to-Cr(0) conversion

Although less toxic than hexavalent chromium, Cr (Ⅲ) species still pose a threat to human health. The Cr (Ⅵ) should be converted to Cr (0) instead of Cr (Ⅲ), which is still involved in biological detoxification filed. Herein, for the first time, it was found that Cr(Ⅵ) can be reduced into Cr(0) by Bacillus cereus FNXJ1-2-3, a way to completely harmless treatment of Cr(Ⅵ). The bacterial strain exhibited excellent performance in the reduction, sorption, and accumulation of Cr(Ⅵ) and Cr (Ⅲ). XPS etching characterization inferred that the transformation of Cr(Ⅵ) into Cr(0) followed a reduction pathway of Cr(Ⅵ)→Cr (Ⅲ)→metallic Cr(0), in which at least two secretory chromium reductases (ECrⅥ→Ⅲ and ECrⅢ→0) worked. Under the optimum condition, the yield ratio of Cr(0)/Cr (Ⅲ) reached 33.90%. In addition, the interfacial interactions, ion channels, chromium reductases, and external electron donors also contributed to the Cr(Ⅵ)/Cr(0) transformation. Findings of this study indicate that Bacillus cereus FNXJ1-2-3 is a promising bioremediation agent for Cr(Ⅵ) pollution control.

Zinc oxide nanoparticles encapsulated in alginate beads: a promising and recyclable adsorbent for simultaneous uptake of toxic metals

Heavy metal toxicity is a known problem and various methods are used for treatment. Adsorption has some advantages and it would be promising if environmentally friendly and cheap materials were utilized. Alginate and zinc oxide nanoparticles were selected and composite alginate beads were used for the removal of mixed metals from aqueous solutions. Batch and column experiments were conducted to determine some parameters' effects and the adsorbent's real application potential. According to the batch experiments, zinc oxide nanoparticles to alginate ratio of 0.5 g g-1, and pH levels nearby to the neutral range led to better metal removals. 0.5 ml min-1of flow rate supplied better metal removal efficiencies in columns, with the highest treatment as 86% of Pb2+. Acid treatment can be successfully applied for the regeneration of the adsorbent, at least three times only with a 4% reduction in the adsorption efficiency. Heavy metal uptake was compatible with the pseudo 2nd order model indicating chemisorption as a dominant mechanism. Also, the intraparticle diffusion model illustrated adsorption might govern more than one step. The Langmuir model had the best fit and suggested monolayer covering for Pb2+, 76.3 mg g-1. Alginate-based nanocomposite beads were useful for mixed metal removal and could be used.

Effective removal and adsorption mechanism of fluoride from water by biochar-based Ce(III)-La(III)-crosslinked sodium alginate hybrid hydrogel

An eco-friendly macroparticle biochar (BC)-based Ce(III)-La(III) crosslinked sodium alginate (SA) hybrid hydrogel (BC/Ce-SA-La) was synthesized by droplet polymerization and characterized by SEM-EDS, XRD, FTIR, UV-Vis and XPS. The effects of dosage, pH, contact time, temperature and coexisting ions on the F- ions removal by hybrid hydrogel, and the adsorption performance, interaction mechanism and reusability were investigated. The results demonstrate that the composite has a fancy wrinkle structure with a particle size of about 1.8 mm and abundant porosity on the surface. The removal rate of F- ions by BC/Ce-SA-La reached 90.2 % under the conditions of pH 2.0, 200 min of contact time and 298 K. The adsorption behavior was perfectly explained by Langmuir model, and the maximum adsorption capacity reached 129 mg/g. The adsorption process was an endothermic spontaneous reaction and followed Pseudo-second-order rate model. The strong adsorption was attributed to multi-interactions including complexation, hydrogen bonding and electrostatic adsorption between the composite and F- ions. Coexisting ions hardly interfered with the adsorption of F- ions by BC/Ce-SA-La except for a slight effect of phosphate. The composite after F- ion adsorption was easily separated and could be reused at least three times. BC/Ce-SA-La is a cost-effective and promising granular biosorbent.

High levels of cadmium altered soil archaeal activity, assembly, and co-occurrence network in volcanic areas

Soil microbial communities are essential to biogeochemical cycles. However, the responses of microorganisms in volcanic soil with high heavy metal levels remain poorly understood. Here, two areas with high levels of cadmium (Cd) from the same volcano were investigated to determine their archaeal composition and assembly. In this study, the Cd concentrations (0.32-0.38 mg/ kg) in the volcanic soils exceeded the standard risk screening values (GB15618-2018) and correlated with archaeal communities strongly (P < 0.05). Moreover, the area with elevated levels of Cd (periphery) exhibited a greater diversity of archaeal species, albeit with reduced archaeal activity, compared to the area with lower levels of Cd (center). Besides, stochastic processes mainly governed the archaeal communities. Furthermore, the co-occurrence network was simplest in the periphery. The proportion of positive links between taxa increased positively with Cd concentration. Moreover, four keystone taxa (all from the family Nitrososphaeraceae) were identified from the archaeal networks. In its entirety, this study has expanded our comprehension of the variations of soil archaeal communities in volcanic areas with elevated cadmium levels and serves as a point of reference for the agricultural development of volcanic soils in China.

Waste treats waste: Facile fabrication of porous adsorbents from recycled PET and sodium alginate for efficient dye removal

Dye-contaminated water and waste plastic both pose enormous threats to human health and the ecological environment, and simultaneously solving these two issues in a sustainable and resource-saving way is highly important. In this work, a sodium alginate-polyethylene terephthalate-sodium alginate (SA@PET) composite adsorbent for efficient dye removal is fabricated using wasted PET bottle and marine plant-based SA via simple and energy-efficient nonsolvent-induced phase separation (NIPS) method. Benefiting from its porous structure and the abundant binding sites, SA@PET shows an excellent methylene blue (MB) adsorption capacity of 1081 mg g-1. The Redlich-Peterson model more accurately describes the adsorption behavior, suggesting multiple adsorption mechanisms. In addition to the electrostatic attractions of SA to MB, polar interactions between the PET matrix and MB are also identified as adsorption mechanisms. It is worth mentioning that SA@PET could be recycled 7 times without a serious decrease in performance, and the trifluoroacetic acid-dichloromethane solvent involved in the NIPS process has the possibility of reuse and stepwise recovery. Finally, the discarded adsorbent could be completely degraded under mild conditions. This work provides not only a composite adsorbent with excellent cationic dye removal performance for wastewater treatment, but also an upcycling strategy for waste PET.

On the performance of Sargassum-derived calcium alginate ion exchange resins for Pb2+ adsorption: batch and packed bed applications

Driven by climate change and human activity, Sargassum blooming rates have intensified, producing copious amount of the invasive, pelagic seaweed across the Caribbean and Latin America. Battery recycling and lead-smelter wastes have heavily polluted the environment and resulted in acute lead poisoning in children through widespread heavy metal contamination particular in East Trinidad. Our study details a comprehensive investigation into the use of Sargassum (S. natans), as a potential resource-circular feedstock for the synthesis of calcium alginate beads utilized in heavy metal adsorption, both in batch and column experiments. Here, ionic cross-linking of extracted sodium alginate with calcium chloride was utilized to create functional ion-exchange beads. Given the low quality of alginates extracted from Sargassum which produce poor morphological beads, composite beads in conjunction with graphene oxide and acrylamide were used to improve fabrication. Stand-alone calcium alginate beads exhibited superior Pb2+ adsorption, with a capacity of 213 mg g-1 at 20 °C and pH 3.5, surpassing composite and commercial resins. Additives like acrylamide and graphene oxide in composite alginate resins led to a 21-40% decrease in Pb2+ adsorption due to reduced active sites. Column operations confirmed Alginate systems' practicality, with 20-24% longer operating times, 15 times lower adsorbent mass on scale-up and 206% smaller column diameters compared to commercial counterparts. Ultimately, this study advocates for Sargassum-based Alginate ion-exchange beads as a bio-based alternative in Trinidad and developing nations for dealing with heavy metal ion waste, offering superior heavy metal adsorption performance and supporting resource circularity.

Enhanced dye sequestration with natural polysaccharides-based hydrogels: A review

Due to the expansion of industrial activities, the concentration of dyes in water has been increasing. The dire need to remove these pollutants from water has been heavily discussed. This study focuses on the reproducible and sustainable solution for wastewater treatment and dye annihilation challenges. Adsorption has been rated the most practical way of the several decolorization procedures due to its minimal initial investment, convenient utility, and high-performance caliber. Hydrogels, which are three-dimensional polymer networks, are notable because of their potential to regenerate, biodegrade, absorb bulky amounts of water, respond to stimuli, and have unique morphologies. Natural polysaccharide hydrogels are chosen over synthetic ones because they are robust, bioresorbable, non-toxic, and cheaply accessible. This study has covered six biopolymers, including chitosan, cellulose, pectin, sodium alginate, guar gum, and starch, consisting of their chemical architecture, origins, characteristics, and uses. The next part describes these polysaccharide-based hydrogels, including their manufacturing techniques, chemical alterations, and adsorption effectiveness. It is deeply evaluated how size and shape affect the adsorption rate, which has not been addressed in any prior research. To assist the readers in identifying areas for further research in this subject, limitations of these hydrogels and future views are provided in the conclusion.

Kinetic and adsorption isotherm studies of Malachite Green dye onto surfactant-tailored alginate hydrogel beads: An influence of surfactant hydrophobicity

This study details the synthesis and characterization of surfactant-modified sodium alginate hydrogel beads crosslinked with Ba2+ ions through ionotropic gelation. Cationic surfactants such as, dodecyltrimethylammonium bromide (DTAB), didodecyldimethylammonium bromide (DDAB), and butanediyl-α,ω-bis-(dimethyldodecylammonium bromide) (GEM), were employed in the modification process. The surfactant-modified ALG-DTAB, ALG-DDAB, and ALG-GEM beads were investigated for the removal of cationic dye Malachite Green (MG) to elucidate the impact of hydrophobicity of amphiphiles on the adsorption process. The characterizations were carried out using Rheometry, Field Emission Scanning Electron Microscopy (FESEM), Infrared Spectroscopy (IR), and Energy Dispersive X-ray Spectroscopy (EDX). Under optimized conditions, ALG-GEM and ALG-DDAB demonstrated highest maximum adsorption capacity (Qmax > 700 mgg-1). The adsorption data fitted well to pseudo-second order kinetic and Langmuir adsorption models, suggesting the involvement of chemisorption phenomena with notable contributions from pore diffusion. The effects of pH, initial dye concentration, adsorbent dose, temperature, and competing ions on the removal of MG were investigated. Interestingly, ALG-GEM beads exhibited an increase in adsorption capacity with rising pH and a subsequent decrease with increasing temperature, showcasing optimal adsorption at pH 7.0 and 25 °C. The study proposes that ALG beads modified with cationic surfactants with higher hydrophobicity could offer a promising avenue in wastewater treatment processes.

Microwave promoted graft copolymerization of poly(ethylacrylate) onto k-carrageenan for removal of Cd and Ni from aqueous solution

Microwave promoted graft copolymerization of poly (ethyl acrylate) onto kappa-carrageenan in presence of a redox pair (ascorbic acid and potassium persulfate) led to the formation of a novel copolymer hydrogel, kappa-carrageenan-graft-poly (ethylacrylate). By varying the reaction conditions such as the microwave power, reaction time, concentration of kappa-carrageenan, ascorbic acid and persulfate, copolymers of highest percentage grafting was obtained and characterized by FT-IR, SEM, TGA and XRD. The copolymer was evaluated as an adsorbent for the adsorption of Ni(II) and Cd(II). Various adsorption parameters such as contact time, pH, initial metal ion concentration, temperature, electrolyte strength and adsorbent dosage were varied to obtain the optimum conditions for the adsorption. The adsorption data for Cd(II), fitted better for Langmuir and Ni(II), fitted much better for Freundlich adsorption isotherm model. Maximum adsorption obtained for cadmium ions and nickel ions was 308.6 mg/g-1 and 305.8 mg/g-1 respectively. The adsorption of both metal ions followed pseudo second order kinetic model. The positive ΔH values endorsed the adsorption process to be endothermic in nature. The negative values of ΔG indicate the spontaneity of the adsorption process while the positive ΔS values showed that the adsorption of metal ions proceeded with increased randomness at the surface of the copolymer. High recovery percentage of the metal ions from the adsorbent indicates that the copolymer can be used for more adsorption cycles.

A novel chitosan-alginate@Fe/Mn mixed oxide nanocomposite for highly efficient removal of Cr (VI) from wastewater: Experiment and adsorption mechanism

In this study, the synthesis and experimental theoretical evaluation of a new chitosan/alginate/hydrozyapatite nanocomposite doped with Mn2 and Fe2O3 for Cr removal was reported. The physicochemical properties of the obtained materials were analyzed using the following methods: SEM-EDX, XRD, FTIR, XPS, pH drift measurements, and thermal analysis. The adsorption properties were estimated based on equilibrium and adsorption kinetics measurements. The Langmuir, Freundlich and Temkin isotherms were applied to analyze the equilibrium data. The thermodynamic analysis of adsorption isotherms was performed. A number of equations and kinetic models were used to describe the adsorption rate data, including pseudo-first (PFOE) and pseudo-second (PSOE) order kinetic equations. The obtained test results show that the synthesized biomaterial, compared to pure chitosan, is characterized by greater resistance to high temperatures. Moreover, this biomaterial had excellent adsorption properties. For the adsorption of Cr (VI), the equilibrium state was reached after 120 min, and the sorption capacity was 455.9 mg/g. In addition, DFT calculations and NCI analyses were performed to get more light on the adsorption mechanism of Cr (VI) on the prepared biocomposite.

Sodium alginate/sodium lignosulfonate hydrogel based on inert Ca2+ activation for water conservation and growth promotion

Soil degradation has become a major global problem owing to the rapid development of agriculture. The problems of soil drought and decreased soil fertility caused by soil degradation severely affect the development of the agricultural and forestry industries. In this study, we designed sodium alginate (SA)/sodium lignosulfonate (SLS) hydrogel based on the activation and crosslinking of inert Ca2+. CaCO3 and SA were mixed, and then, inert Ca2+ was activated to prepare a gel with a stable structure and a uniform interior and exterior. The crosslinking activated by inert Ca2+ enhanced the stability of the hydrogel, and the optimal swelling rate of the hydrogel reached 28.91 g/g, thereby effectively improving the water-holding capacity of the soil (77.6-108.83 g/kg). SLS was degraded into humic acid (HA) and gradually released, demonstrating a positive growth-promoting effect in plant growth experiments. The SA/SLS hydrogel can be used for soil water retention and mitigation to significantly decrease the water loss rate of soil. This study will assist in addressing soil drought and fertility loss.

Removal of heavy metals from wastewater by aerogel derived from date palm waste

Cellulose that has been sourced from date palm leaves as a primary component was utilised. This cellulose served as the foundational material for the development of an aerogel composite. During this process, MXene (Ti3C2Tx) played a pivotal role in enhancing the overall composition of the aerogel. To ensure the stability and durability of the resulting aerogel structure, calcium ions were introduced to the mix. These ions facilitated the cross-linking process of sodium alginate molecules, ultimately leading to the formation of calcium alginate. This cross-linking step is crucial for the enhanced mechanical and chemical stability of the aerogel. Incorporating alginate and Ti3C2Tx into the cellulose aerogel enhanced its structural integrity in aqueous conditions and increased its adsorption capacity. When evaluated with synthetic wastewater, this composite exhibited remarkable adsorption capacities of 72.9, 114.4, 92.9, and 123.9 mg/g for As, Cd, Ni, and Zn ions, respectively. A systematic study was carried out to see the effect of various parameters, including contact time, MXene concentration, pH, and temperature on the adsorption of these elements. Peak adsorption was achieved at 60 min, favoring a pH range between 6 and 8 and exhibited optimal sorption efficiency at lower temperatures. The adsorption kinetics adhered closely to a pseudo-second-order, while the Freundlich model adeptly described the adsorption isotherms. An interesting result of this research was the aerogel's regenerative potential. After undergoing a basic acid treatment, the MXene/cellulose/alginate aerogel composite could be restored and reused for up to three cycles, all while maintaining its core performance capabilities even after the rigorous cross-linking processes. In three consecutive cycles, the removal percentages for As, Cd, Ni, and Zn were 48.15%, 80.38%, 56.51%, and 86.12% in cycle 1; 37.35%, 65.63%, 45.97%, and 78.42% in cycle 2; and 28.60%, 56.22%, 34.70%, and 65.83% in cycle 3, respectively. The composite was tested in conditions resembling seawater salinity. Impressively, the aerogel continued to demonstrate a significant ability to adsorb metals, reinforcing its potential utility in real-world aquatic scenarios. These findings suggest that the composite aerogel, integrating MXene, cellulose, and alginate, is an effective medium for the targeted removal of heavy metals from aquatic environments.

Enhanced Cr(VI) stabilization by terrestrial-derived soil protein: Photoelectrochemical properties and reduction mechanisms

Glomalin-related soil protein (GRSP) is a stable iron-organic carbon mixture that can enhance heavy metal sequestration in soils. However, the roles of GRSP in the transformation and fate of Cr(VI) have been rarely reported. Herein, we investigated the electrochemical and photocatalytic properties of GRSP and its mechanisms in Cr(VI) adsorption and reduction. Results showed that GRSP had a stronger ability for Cr(VI) adsorption and reduction than other biomaterials, with the highest adsorption amount of up to 0.126 mmol/g. The removal efficiency of Cr(VI) by GRSP was enhanced (4-7%) by ultraviolet irradiation due to the hydrated electrons produced by GRSP. Fe(II) ions, persistent free radicals, and oxygen-containing functional groups on the GRSP surface as electron donors participated in the reduction of Cr(VI) under dark condition. Moreover, Cr(III) was mainly adsorbed on the -COOH groups of GRSP via electrostatic interactions. Based on 2D correlation spectroscopy, the preferential adsorption occurred on the GRSP surface for Cr(VI) in the sequential order of CO → COO- → O-H → C-O. This work provides new insights into the Cr(VI) adsorption and reduction mechanism by GRSP. Overall, GRSP can serve as a natural iron-organic carbon for the photo-reduction of Cr(VI) pollution in environments.

Alginate-encapsulated biochar as an effective soil ameliorant for reducing Pb phytoavailability to lettuce (Lactuca sativa L.)

The alginate-biochar formulation for metal removal from aquatic environments has been widely tried but its use for lowering phytoavailability of metals in the soil-crop continuum is limited. Biochar has been increasingly used as a soil amendment due to its potential for soil carbon sequestration and sorption capacity. Handling of powdery biochar as a soil top-dressing material is, however, cumbersome and vulnerable to loss by water and wind. In this experiment, biochar powder, which was pyrolyzed from oak trees, was encapsulated into beads with alginate, which is a naturally occurring polysaccharide found in brown algae. Both batch and pot experiments were conducted to examine the effects of the alginate-encapsulated biochar beads (BB), as compared to its original biochar powdery form (BP), on the Pb adsorption capacity and phytoavailability of soil Pb to lettuce (Lactuca sativa L.). The BB treatment improved reactivity about six times due to a higher surface area (287 m2 g-1) and five times due to a higher cation exchange capacity (50 cmolc kg-1) as compared to the BP treatment. The maximum sorption capacity of Pb was increased to 152 from 81 mg g-1 because of surface chemosorption. Adsorption of Pb onto BB followed multiple first-order kinetics and comprised fast and slow steps. More than 60% of the Pb was adsorbed in the fast step, i.e., within 3 h. Also, the BB treatment, up to the 5% level (w/w), increased soil pH from 5.4 to 6.5 and lowered the phytoavailable fraction of Pb in soil from 5.7 to 0.3 mg kg-1. The Pb concentrations in lettuce cultivated at 5% for the BP and BB treatments were similar but 63 and 66% lower, respectively, than those of the control soil. The results showed that the encapsulation of biochar with alginate enhanced adsorption by the biochar.

Adsorption of Metal Ions from Single and Binary Aqueous Systems on Bio-Nanocomposite, Alginate-Clay

The aim of this work is to characterize and evaluate the retention of Cu2+ and Ni2+ from single and binary systems by alginate-Moroccan clay bio-composite with the utilization of calcium chloride as a cross-linking agent, using the ionotropic gelation method. The bio-nanocomposite was characterized by using a variety of techniques (SEM, EDX, XRD, and pHPZC). The efficiency of the adsorbent was investigated under different experimental conditions by varying parameters such as pH, initial concentration, and contact time. To demonstrate the adsorption kinetics, various kinetic models were tried and assessed, including pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich models. The research results show that the adsorption process of Cu2+ and Ni2+ metal ions follows a pseudo-second-order kinetic model, and the corresponding rate constants were identified. To evaluate the parameters related to the adsorption process in both single and binary systems, different mathematical models of isotherms, such as Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich, were investigated. The correlation coefficients obtained showed that the most suitable isotherm for describing this adsorption process is the Langmuir model. The process is considered to be physical and endothermic, as suggested by the positive values of ΔH° and ΔS°, indicating increased randomness at the solid/liquid interface during Cu2+ and Ni2+ adsorption. Furthermore, the spontaneity of the process is confirmed by the negative values of ∆G°. The bio-nanocomposite beads demonstrated a maximum adsorption capacity of 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ in the single system. In the binary system, the maximum adsorption capacities were observed to be 357.14 mg/g for Ni2+ and 370.37 mg/g for Cu2+. There is significant evidence for the use of alginate-Moroccan clay bio-nanocomposite as a cost-effective alternative adsorbent for the efficient removal of metal ions in single and binary systems.

Development of a Near-Zero-Waste Valorization Concept for Waste NdFeB Magnets: Production of Antimicrobial Fe Alginate Beads via Adsorption and Recovery of High-Purity Rare-Earth Elements

Nowadays, with the evolution of technology, rare earths are raw materials for a multitude of products, especially in high technological applications. A high amount of REEs is used in the production of permanent magnets, particularly NdFeB. The demand for some of the REEs, including neodymium, praseodymium, and dysprosium, is expected to increase in the coming years. REEs are defined as critical materials due to their high supply risk and economic importance. Recycling secondary raw materials for supplying REEs in the future is one promising option, and one of the best candidates is NdFeB magnets. NdFeB magnets include approximately 30% REEs and 66% of iron. For the near-zero-waste concept, the recovered iron from NdFeB must be evaluated in other applications. In this study, the near-zero-waste valorization concept for EoL-NdFeB magnets is developed, and high-purity REEs are achieved with a two-step process, including leaching and adsorption using alginate beads. Moreover, antimicrobial Fe alginate beads are produced in the leach liquor via adsorption. The antimicrobial activity of the produced Fe alginate beads is evaluated with disc diffusion and broth dilution methods against Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli. The most effective antibacterial Fe alginate beads are against E. coli and S. aureus with inhibitions of 87.21 and 56.25%, respectively.

Mechanism of heavy metal ion biosorption by microalgal cells: A mathematic approach

Microalgal biomasses have been established as promising biosorbents for biosorption to remove heavy metal ions (HMIs) from wastewaters and contaminated natural waterbodies. Understanding the mechanism is important for the development of cost-effective processes for large scale applications. In this paper, a simple mathematical model was proposed for the predication of biosorption capacity of HMI by microalgal cells based on single cell mass, cell size, and HMI radius. One fundamental assumption based on which this model was developed, i.e., the biosorption of HMI by microalgal cells is predominantly monolayer bio-adsorption, was established based on kinetic, isothermal, FTIR, and Pb(II) distribution data generated in this study and in literature. The model was validated using a combination of experimental and literature data as well, demonstrating its capability to provide reasonable estimations although with discrepancies. The biosorption capacities of HMIs (mmol/g) by Chlorella vulgaris were experimentally determined to be in the following order: Pb(II)(0.360)> Zn(II)(0.325)> Cu(II)(0.254)> Ni(II)(0.249)> Cd(II)(0.235)> Co(II)(0.182). We systematically investigated the deviations of the predicted biosorption capacities in term of the effects of a few important parameters that were unaccounted for in the model, including the nanostructures on cell surface, HMI electronegativity, and biosorption buffer pH. Results suggest that the nanostructures on cell wall, likely the hairlike fibers, might be the primary locations where the binding sites for HMI were housed. Furthermore, isothermal data, which is suported by the predictions of this model, indicate the each effective binding site on C. vulgaris cell surface could bind to more than one Co(II) in biosorption while each of the other five HMIs tested in this study required more than one binding sites.

Recent Developments in Functional Polymers via the Kabachnik-Fields Reaction: The State of the Art

Recently, multicomponent reactions (MCRs) have attracted much attention in polymer synthesis. As one of the most well-known MCRs, the Kabachnik-Fields (KF) reaction has been widely used in the development of new functional polymers. The KF reaction can efficiently introduce functional groups into polymer structures; thus, polymers prepared via the KF reaction have unique α-aminophosphonates and show important bioactivity, metal chelating abilities, and flame-retardant properties. In this mini-review, we mainly summarize the latest advances in the KF reaction to synthesize functional polymers for the preparation of heavy metal adsorbents, multifunctional hydrogels, flame retardants, and bioimaging probes. We also discuss some emerging applications of functional polymers prepared by means of the KF reaction. Finally, we put forward our perspectives on the further development of the KF reaction in polymer chemistry.

Multichannel Multijunction Droplet Microfluidic Device to Synthesize Hydrogel Microcapsules with Different Core-Shell Structures and Adjustable Core Positions

Core-shell hydrogel microcapsules have sparked great interest due to their unique characteristics and prospective applications in the medical, pharmaceutical, and cosmetic fields. However, complex synthetic procedures and expensive costs have limited their practical application. Herein, we designed and prepared several multichannel and multijunctional droplet microfluidic devices based on soft lithography for the effective synthesis of core-shell hydrogel microcapsules for different purposes. Additionally, two different cross-linking processes (ultraviolet (UV) exposure and interfacial polymerization) were used to synthesize different types of core-shell structured hydrogel microcapsules. Hydrogel microcapsules with gelatin methacryloyl (GelMA) as the core and polyacrylamide (PAM) as the thin shell were synthesized using UV cross-linking. Using an interfacial polymerization process, another core-shell structured microcapsule with GelMA as the core and Ca2+ cross-linked alginate with polyethylenimine (PEI) as the shell was constructed, and the core diameter and total droplet diameter were flexibly controlled by carving. Noteworthy, these hydrogel microcapsules exhibit stimuli-responsiveness and controlled release ability. Overall, a novel technique was developed to successfully synthesize various hydrogel microcapsules with core-shell microstructures. The hydrogel microcapsules possess a multilayered structure that facilitates the coassembly of cells and drugs, as well as the layered assembly of multiple drugs, to develop synergistic therapeutic regimens. These adaptable and controllable hydrogel microdroplets shall held great promise for multicell or multidrug administration as well as for high-throughput drug screening.

A novel approach to modify Stenotrophomonas sp. D6 by regulating the salt composition in the growth medium: Enhanced removal performance of Cr(VI)

In this study, a novel and effective modified microbial reducing agent was developed to detoxify Cr(VI) from aqueous solutions. This was achieved by carefully controlling specific salt components in the growth medium. Based on the single-salt modification, several effective modified salts were selected and added to the medium for synergistic modification. The results showed that the synergistic modification with NH4Cl and KH2PO4 had the best detoxification effect on Cr(VI), reaching 98.5% at 100 mg/L Cr(VI), which was much higher than the 43.7% of the control (original Luria-Bertani medium). This enhancement was ascribed to the ability of NH4Cl and KH2PO4 to stimulate the growth of Stenotrophomonas sp. D6 promoted chromate reductase secretion. The protein content of the modified medium supernatant was significantly increased by 10.76% compared to that before modification. Based on the micro-characterization, the main process for the elimination of Cr(VI) is microbial reduction rather than biosorption. Most of the reduced Cr was found in the extracellular suspension, thereby suggesting that the primary reduction occurred outside the cells, whereas only a small fraction was detected intracellularly. Overall, this study provides a simple and effective method for microbial treatment of heavy metals in aqueous solutions.

Enzyme-triggered approach to reduce water bodies' contamination using peroxidase-immobilized ZnO/SnO2/alginate nanocomposite

Enzyme immobilization on solid support offers advantages over free enzymes by overcoming characteristic limitations. To synthesize new stable and hyperactive nano-biocatalysts (co-precipitation method), ginger peroxidase (GP) was surface immobilized (adsorption) on ZnO/SnO2 and ZnO/SnO2/SA nanocomposite with immobilization efficacy of 94 % and 99 %, respectively. Thereafter, catalytic and biochemical characteristics of free and immobilized GP were investigated by deploying various techniques, i.e., FTIR, PXRD, SEM, and PL. Diffraction peaks emerged at 2θ values of 26°, 33°, 37°, 51°, 31°, 34°, 36°, 56°, indicating the formation of SnO2 and ZnO. The OH stretching of the H2O molecules was attributed to broad peaks between 3200 and 3500 cm-1, whereas ZnO/SnO2 spikes occurred in the 1626-1637 cm-1 range. SnO stretching mode and ZnO terminal vibrational patterns have been verified at corresponding wavelengths of 625 cm-1 and 560 cm-1. Enzyme entrapment onto substrate was verified via interactions between GP and ZnO/SnO2/SA as corroborated by signals beneath 1100 cm-1. GP-immobilized fractions were optimally active at pH 5, 50 °C, and retained maximum activity after storage of 4 weeks at -4 °C. Kinetic parameters were determined by using a Lineweaver-Burk plot and Vmax for free GP, ZnO/SnO2/GP and ZnO/SnO2/SA/GP with guaiacol as a substrate, were found to be 322.58, 49.01 and 11.45 (μM/min) respectively. A decrease in values of Vmax and KM indicates strong adsorption of peroxidase on support and maximum affinity between nano support and enzyme, respectively. For environmental remediation, free ginger peroxidase (GP), ZnO/SnO2/GP and ZnO/SnO2/SA/GP fractions effectively eradicated highly intricate dye. Multiple scavengers had a significant impact on the depletion of the dye. In conclusion, ZnO/SnO2 and ZnO/SnO2/SA nanostructures comprise an ecologically acceptable and intriguing carrier for enzyme immobilization.

Sodium alginate hydrogel-encapsulated trans-anethole based polymer: Synthesis and applications as an eradicator of metals and dyes from wastewater

Clean and safe water resources are essential for environmental safety and human health. Hydrogels and biomass polymers have attracted considerable attention in recent years, considering their nontoxicity, controllable performance, and high adsorption capacity. The interpenetrating network described here is a combination of a biomass polymer and a hydrogel adsorbent was established, the biomass polymer microspheres were first prepared with the combination of biomass monomer trans-anethole and maleic anhydride copolymer. A simple, environmentally friendly, and facile method of incorporating biomass polymer into sodium alginate biopolymer was developed by introducing the cross-linking agents calcium chloride and glutaraldehyde into the biomass polymer. Furthermore, the biomass polymer sodium alginate hydrogel (BP@SA/H) was characterized by FTIR, XPS, SEM, and XRD. In order to test materials' performance, the removal of pollutants and the adsorption study were also investigated after and before adsorption toward metals and dyes in water. We examined the factors influencing the materials, adsorption capability, such as initial concentration, time, absorbent amount, and pH. Moreover, the maximum adsorption values for Pb+2 and Cd+2 were 734.9 and 722 mg/g. While the adsorption toward RhB dye are 745 mg/g. In addition, the adsorption results were investigated using kinetic and isothermal models, demonstrating that biomass polymer hydrogel adsorption is chemisorption. Therefore, the as-developed biomass polymer sodium alginate hydrogel (BP@SA/H) is an exceptional multifunctional material that can be used to remove hazardous pollutants from wastewater.

Facile synthesis and ultrastrong adsorption of a novel polyacrylamide-modified diatomite/cerium alginate hybrid aerogel for anionic dyes from aqueous environment

An eco-friendly cationic polyacrylamide (CPAM)-modified diatomite/Ce(III)-crosslinked sodium alginate hybrid aerogel (CPAM-Dia/Ce-SA) was synthesized successfully and characterized by SEM-EDS, XRD, FTIR, UV-Vis and XPS. Adsorption performance, interaction mechanism and reusability of CPAM-Dia/Ce-SA used for the removal of acid blue 113 (AB 113), acid blue 80 (AB 80), acid yellow 117 (AY 117), Congo red (CR) and Direct Green 6 (DG 6) anionic dyes from aqueous media were investigated in detail. The results demonstrate that CPAM-Dia/Ce-SA aerogel is macroscopic polymer hybrid spheres with a particle size of around 1.3 mm, unique undulating mountain-like surface and porous mesostructure, and exhibits outstanding adsorption capacity for anionic dyes and good reusability. The maximum adsorption amounts of AB 113, AB 80, AY 117, CR and DG 6 by CPAM-Dia/Ce-SA were 3008, 1208, 914, 1832 and 1232 mg/g at pH 2.0, 60 min contact time and 25 °C, and corresponding removal efficiency reached individually 97.5, 96.6, 99.7, 99.9 and 98.5 % respectively and were less affected by increasing pH up to 10.0. Dye adsorption behaviour and adsorption processes with spontaneous and exothermic nature were perfectly interpreted by the Langmuir and Pseudo-second-order rate models respectively. Physicochemical and multisite-H-bonding synergies promoted the ultrastrong biosorption of anionic dyes by CPAM-Dia/Ce-SA.

Effect of the magnetic core in alginate/gum composite on adsorption of divalent copper, cadmium, and lead ions in the aqueous system

The change of composition of an adsorbent material has been widely used as a method to increase its adsorption capacity, particularly concerning adsorbents made of polysaccharides. Introducing magnetic adsorbents into contaminated water treatment systems is a highly promising strategy, as it promotes the metal ions removal from water. Considering this, gum Arabic (GA) was associated with alginate (Alg), when magnetite nanoparticles were present or absent, to produce beads that were utilised to take up Cu(II), Cd(II), and Pb(II) from aqueous solution. After a complete characterisation (for which Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and swelling were used), the adsorption properties were established using batch and column tests. The magnetic beads (MAlg/GA) demonstrated improved adsorption in comparison with the beads made without magnetite (Alg/GA) under the same conditions. In normal adsorption conditions (pH 6.0, 25 °C, 2.5 g L-1 of adsorbent dosage), the highest uptake capacities recorded for the MAlg/GA beads were: for Cu(II), 1.33 mmol g-1; Cd(II), 1.59 mmol g-1; and for Pb(II), 1.43 mmol g-1. The pseudo-second-order kinetics and Langmuir isotherm models provided good fits for the adsorption of these metals. Overall, ion exchange and physical forces led to the uptake of these metals by both Alg/GA and MAlg/GA; moreover, the functional groups on the beads played crucial roles as binding sites. Additionally, it was observed that flow rates of >2 mL min-1 did not produce noticeable changes in uptake levels over the same flow period. It was found that the efficient eluting agent was HNO3 (0.2 M). In some cases, the metals were not removed fully from the used beads during the first five cycles of regeneration and reuse. The results of this investigation show that these beads are efficient adsorbents for the removal of metal ions from spiked well water samples.

Effect of biocomposite production factors on the development of an eco-friendly chitosan/alginate-based adsorbent with enhanced copper removal efficiency

Nowadays, wastewater treatment is a critical concern, particularly regarding the removal of heavy metals through adsorption methods. Extensive research has been conducted on obtaining high-yield and environmentally friendly adsorbents. Natural polymer adsorbents especially have shown promise in ion and organic molecule adsorption. To enhance the practical applicability of adsorbents, the combination of biopolymers to form biocomposites is a promising alternative. In this study, adsorbents based on a 1:1 wt./wt. of chitosan (CS) and alginate (SA) were prepared. The influence of the regeneration route and drying conditions on the copper adsorption capacity was investigated, along with reaction parameters such as contact time, adsorbent particle size, and pH. The highest adsorption capacity was observed in the composite material obtained through a one-pot regeneration process and freeze-dried. The CSAR3L sample exhibited a remarkable adsorption capacity of 288 mg Cu(II)/g after 360 min at 25 °C. The synergistic effect between the CS and SA precursors was confirmed by analyzing the individual precursors and their mechanical mixture. The initial adsorption rates at pH 6 followed the order: CSAR3-L > Bk-CSR3L > Bk-SAR3L + Bk-CSR3L > Bk-SAR3L. The physicochemical and morphological properties of the materials were studied by FTIR, XRD, DLS, XPS, optical microscopy, EDS-SEM, elemental chemical analysis, and TGA-DTG. The utilization of different drying methods resulted in the formation of calcium carbonate crystalline phases in the as-prepared materials, thus creating substantial adsorption active sites. After the adsorption process, hydroxylated copper sulfate phases and a significant decrease in calcium concentration were observed, indicating that an ion exchange adsorption mechanism occurred. The analysis of adsorption kinetics and the shape of the adsorption isotherms, in agreement with the characterization results, suggested the presence of multiple active sites and the formation of a chemisorption monolayer.

Study on adsorption of salicylic acid and sulfosalicylic acid by MOF-sodium alginate gel beads obtained in a green way

A composite (ZS-UiO-66-NH2) zirconium crosslinked sodium alginate gel beads (ZS)-metal-organic skeleton (UiO-66-NH2) were prepared in this study through in-situ growth under simple, green and mild conditions for removal of the salicylic acid (SA) and sulfosalicylic acid (SSA) from water. The physicochemical properties of ZS-UiO-66-NH2 were characterized using various analytical methods. The influencing factors in the adsorption process including pH of solution, amount of adsorbent, coexisting ions, adsorption time, reaction temperature and equilibrium concentration of SA/SSA were performed in batch adsorption. The experimental results indicated that ZS-UiO-66-NH2 had high stability and could achieve efficient adsorption of SA/SSA in broad pH range (2-9) and salinity (0-0.2 mol·L-1). SA and SSA adsorbed on the composite at 293 K reached high values of 193 and 167 mg·g-1 from Langmuir model, respectively. Kinetic and isotherm studies demonstrated that the adsorption processes were mainly multilayer heterogeneous chemisorption. Thermodynamic data manifested that the two processes were exothermic and spontaneous with increasing entropy. ZS-UiO-66-NH2 can effectively remove SA/SSA from simulated wastewater under different pH and can be reused after elution with a NaHCO3 solution (5 mmol·L-1). The ZS-UiO-66-NH2 composite has great potential for removing SA/SSA from actual water bodies.

Tannic acid-assisted fabrication of antibacterial sodium alginate-based gel beads for the multifunctional adsorption of heavy metal ions and dyes

The existence of heavy metals and dyes seriously affects the ecological environment and human safety. Antibacterial adsorption materials with the broad-spectrum removal of multiple pollutants are urgently required for water remediation. Herein, a sustainable and antibacterial sodium alginate (SA) gel bead adsorbent with honeycomb cellular architecture is developed by the biomimetic deposition polyphenolic tannic acid (TA) induced grafting diethylenetriamine (DETA) under mild conditions for efficient removal of Cr(VI) and dyes. Taking advantage of the catechol surface chemistry, TA occurring rapid polymerization with DETA monomers not only enhances the water resistance and thermal stability of the gel bead, but also introduces abundant polyphenolic functional groups and active adsorption sites. The multifunctional gel bead showed outstanding antibacterial activity against S. aureus (sterilization rates: 83.8 %) and E. coli (sterilization rates: 99.5 %). The maximum adsorption capacity of gel bead for Cr(VI) was 163.9 mg/g. Moreover, the removal efficiency of the gel bead for dyes of Safranine T and Rhodamine B was 89.5 % (maximum adsorption capacity: 537 mg/g) and 76.7 % (maximum adsorption capacity: 460.2 mg/g), respectively, indicating its excellent broad-spectrum adsorption performance for multiple pollutants. Therefore, TA-assisted fabrication of SA-based gel bead with excellent antibacterial property is a promising multifunctional adsorption material for practical water remediation.

An optimized 3D-printed capsule scaffold utilizing artificial neural network for the targeted delivery of chlorogenic acid to the colon

Chlorogenic acid (CGA) is an important bioactive polyphenol with extensive biological properties. This study aimed to fabricate an optimized three-dimensional (3D)-printed capsule scaffold and CGA capsules for targeted delivery of hydrophobic CGA to the colon. The optimized printing parameters identified using the neural network model were a temperature of 170 °C, a printing speed of 20 mm/s, and a nozzle diameter of 0.3 mm. The capsules exhibited slow releasing properties of CGA, and the releasing rates of Eudragit®FS 30D-sealed capsules (due to more cracks and voids) were faster than those of Eudragit®S100-sealed capsules. The Ritger-peppas model was the best fitting model to describe the releasing process of CGA from 8 CGA capsules (R2 ≥ 0.98). All CGA capsules exhibited shear-thinning properties with stable sol-gel viscosity at low shear rates. FTIR spectra confirmed the formation of non-covalent bonds between CGA and the sol. Overall, the obtained 3D-printed capsules provided a promising carrier for the targeted delivery of CGA in the development of personalized dietary supplements.

Batch Experimental Studies and Statistical Modeling for the Effective Removal of Tetracycline from Wastewater Using Bimetallic Zn-Cu-Metal-Organic Framework@Hydrogel Composite Beads

Antimicrobial resistance (AMR) is on an upsurge as more and more broad-spectrum antibiotics are being used haphazardly, resulting in imbalances in the ecosystem and disrupting common/systematic clinical protocols. To combat this issue, metal-organic framework embedded zinc-copper-benzenedicarboxylate@calcium alginate composite beads (Zn-Cu-BDC@CA CBs) were synthesized and utilized for the adsorption of tetracycline (TC) from water. The surface morphology, presence of functional groups, surface area, and thermal stability of Zn-Cu-BDC@CA CBs were evaluated by field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), and thermal gravimetric analysis (TGA), respectively. Batch adsorption experiments were also carried out to optimize the adsorption performance of Zn-Cu-BDC@CA CBs for TC by adjusting the key parameters, including pH of the solution, contact time, adsorbent dosage, temperature, and initial concentration of TC. From the RSM model, 96.8% removal of TC takes place under the optimum conditions (pH = 7.3, mass = 17.2 mg, concentration = 21.3 ppm, time = 3.4 h, and temperature = 31.8 °C), which aligns closely with the experimental batch study, where the addition of 20 mg of adsorbent to a 20 mL TC solution (20 mg/L) at a pH of 7 and a temperature of 27 °C yielded an impressive TC removal efficiency of 96.55% within 180 min. Zn-Cu-BDC@CA CBs possess homogeneous adsorption surfaces, and TC is adsorbed via monolayer chemisorption, according to the results derived from the Langmuir isotherm model and pseudo-second-order kinetic model. The thermodynamic analysis indicated that the adsorption process is both endothermic and spontaneous. In their entirety, the synthesized Zn-Cu-BDC@CA CBs exhibit certain operational advantages, such as simple separation, satisfactory adsorption performance, and decent recyclability, indicating their viability for industrial application of elimination of TC residues from aquatic environments.

Magnetic Hydrogel Beads as a Reusable Adsorbent for Highly Efficient and Rapid Removal of Aluminum: Characterization, Response Surface Methodology Optimization, and Evaluation of Isotherms, Kinetics, and Thermodynamic Studies

Biopolymers such as alginate and gelatin have attracted much attention because of their exceptional adsorption properties and biocompatibility. The magnetic hydrogel beads produced and used in this study had a core structure composed of magnetite nanoparticles and gelatin and a shell structure composed of alginate. The combination of the metal-ion binding ability of alginate and the mechanical strength of gelatin in magnetic hydrogel beads presents a new approach for the removal of metal from water sources. The beads were designed for aluminum removal and fully characterized using various methods, including Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy-energy-dispersive X-ray spectroscopy, vibrating sample magnetometry, microcomputed tomography, and dynamic mechanical analysis. Statistical experimental designs were employed to optimize the parameters of the adsorption and recovery processes. Plackett-Burman Design, Box-Behnken Design, and Central Composite Design were used for identifying the significant factors and optimizing the parameters of the adsorption and recovery processes, respectively. The optimum parameters determined for adsorption are as follows: pH: 4, contact time: 30 min, adsorbent amount: 600 mg; recovery time: reagent 1 M HNO3; and contact time: 40 min. The adsorption process was described by using the Langmuir isotherm model. It reveals a homogeneous bead surface and monolayer adsorption with an adsorption capacity of 5.25 mg g-1. Limit of detection and limit of quantification values were calculated as 4.3 and 14 μg L-1, respectively. The adsorption process was described by a pseudo-second-order kinetic model, which assumes that chemisorption is the rate-controlling mechanism. Thermodynamic studies indicate that adsorption is spontaneous and endothermic. The adsorbent was reusable for 10 successive adsorption-desorption cycles with a quantitative adsorption of 98.2% ± 0.3% and a recovery of 99.4% ± 2.6%. The minimum adsorbent dose was determined as 30 g L-1 to achieve quantitative adsorption of aluminum. The effects of the inorganic ions were also investigated. The proposed method was applied to tap water and carboy water samples, and the results indicate that magnetic hydrogel beads can be an effective and reusable bioadsorbent for the detection and removal of aluminum in water samples. The recovery values obtained by using the developed method were quantitative and consistent with the results obtained from the inductively coupled plasma optical emission spectrometer.

The self-regulating on cohesion properties of calcium phosphate/ calcium sulfate bone cement improved by citric acid/sodium alginate

Calcium phosphate cement (CPC) has attracted extensive interest from surgeons and materials scientists. However, the collapsibility of calcium phosphate cement limits its clinical application. In this work, a gel network of SA-CA formed by the reaction of citric acid (CA) and sodium alginate (SA) was introduced into the α-TCP/α-CSH composite. Furthermore, a high proportion of α-CSH provided more calcium sources for the system to combine with SA forming a gel network to improve the cohesion property of the composite, which also played a regulating role in the conversion of materials to HA. The morphology, physicochemical properties, and cell compatibility of the composites were studied with SA-CA as curing solution. The results show that SA-CA plays an important role in the compressive strength and collapse resistance of bone cement, and its properties can be regulated by changing the content of CA. When CA is 10 wt%, the mechanical strength is the highest, reaching 12.49 ± 2.03 MPa, which is 265.80% higher than water as the solidifying liquid. In addition, the cell experiments showed that the samples were not toxic to MC3T3 cells. The results of ALP showed that when SA-CA were used as curing solution, the activity of ALP was higher than that of blank sample, indicating that the composite bone cement could be conducive to the differentiation of osteoblasts. In this work, the α-CSH/α-TCP based composite regulated by gel network of SA-CA can provide a promising strategy to improve the cohesion of bone cement.

Current application and modification strategy of marine polysaccharides in tissue regeneration: A review

Marine polysaccharides (MPs) are exceptional bioactive materials that possess unique biochemical mechanisms and pharmacological stability, making them ideal for various tissue engineering applications. Certain MPs, including agarose, alginate, carrageenan, chitosan, and glucan have been successfully employed as biological scaffolds in animal studies. As carriers of signaling molecules, scaffolds can enhance the adhesion, growth, and differentiation of somatic cells, thereby significantly improving the tissue regeneration process. However, the biological benefits of pure MPs composite scaffold are limited. Therefore, physical, chemical, enzyme modification and other methods are employed to expand its efficacy. Chemically, the structural properties of MPs scaffolds can be altered through modifications to functional groups or molecular weight reduction, thereby enhancing their biological activities. Physically, MPs hydrogels and sponges emulate the natural extracellular matrix, creating a more conducive environment for tissue repair. The porosity and high permeability of MPs membranes and nanomaterials expedite wound healing. This review explores the distinctive properties and applications of select MPs in tissue regeneration, highlighting their structural versatility and biological applicability. Additionally, we provide a brief overview of common modification strategies employed for MP scaffolds. In conclusion, MPs have significant potential and are expected to be a novel regenerative material for tissue engineering.

Modified alginate materials for wastewater treatment: Application prospects

Sodium alginate is a natural macromolecule widely used because of its abundance, low cost of acquisition, and rich hydroxyl and carboxyl groups in the matrix. The physical modification of sodium alginate can be made by blending it with polymer materials. The so-yielded alginate complex is commonly unstable in an aqueous environment due to alginate backbones' high hydrophilicity. The chemical modification can remove its hydrophilic groups and introduce special functional groups or polymers onto the alginate backbones to provide excess reaction sites for specific reactions and effective complexation sites for accommodating antibiotics, dyes, heavy metal ions, and radioactive elements. Sodium alginate has been used in water treatment engineering under revised modification protocols. This article also reviews the latest modification protocols for sodium alginate and outlines the novel application of the modified materials. The limitations of modified sodium alginate materials are described, and research prospects are put forward.

Fabrication of sodium alginate-doped carbon dot composite hydrogel and its application for La (III) adsorption and enhanced the removal of phosphorus

Adsorption is an effective method for the removal of hazardous substances from wastewater. In this work, a low-cost and environmental-friendly composite hydrogel material of sodium alginate doped with nitrogen doped carbon dots (SA@NCDs) was fabricated by impregnation for lanthanide and enhanced phosphorus adsorption in wastewater. The effects of NCDs doping amount, dosage, pH, initial solution concentration, adsorption time and temperature on the process of La (III) adsorption by SA@NCDs were investigated. The adsorption isotherms fitted to Langmuir isotherm model (R2 = 0.9970-0.9989) and the adsorption kinetics followed pseudo-second-order kinetic model (R2 = 0.9992). The maximum adsorption capacity of the adsorbent for La (III) was 217.39 mg/g according to the Langmuir model at 298.15 K. After five cycles, the removal efficiency of La (III) adsorbed by SA@NCDs was still 85.1%. Moreover, the loaded La (III) enhanced the adsorption of phosphorus. The La (III)-SA@NCDs-5 hydrogel adsorbent greatly improved the adsorption capacity for phosphorus compared with the La (III)-free adsorbent, and the adsorption amount can reach 9.64 mg-P/g. The SA@NCDs complex hydrogels for rare earth adsorption were prepared by introducing NCDs rich in amino group into SA hydrogels. The introduction of NCDs increases the adsorption sites of hydrogels, and also overcomes the problem that NCDs itself is difficult to recover in wastewater treatment applications. The lanthanide adsorbed material has a stable structure and can be used to remove phosphorus to deal with waste using the waste. It indicates the SA@NCDs hydrogel composite adsorbent have good potential for wastewater treatment.

Enhancing the efficiency of Ni(II), Cd(II), and Cu(II) adsorption from aqueous solution using schist/alginate composite: batch and continuous studies

The main aim of this research is focused on the synthesis of schist/alginate composite (SC/AL) adsorbent and its utilization for the removal of Ni(II), Cu(II), and Cd(II) from waste streams using batch and column processes. The characterization of developed adsorbent was performed by X-ray fluorescence, X-ray diffraction, FTIR, and BET analyses. The most influential operating parameters (pH, contact time, temperature and initial adsorbate concentration) on the adsorption capacity of pollutants were examined to evaluate the performance of developed adsorbent. The kinetic and equilibrium adsorption results at pH 5.0 indicated that SC/AL composite had good adsorption capacity (qmax) for Ni(II), Cu(II), and Cd(II) estimated at 124.79 mg/g, 111.78 mg/g, and 119.78 mg/g, respectively. From the kinetic viewpoint, the good fit of pseudo-first-order kinetic model to the kinetic adsorption data indicated that dominant interaction of heavy metals with SC/AL composite was physisorption. The results of thermodynamic studies indicated that the adsorption of heavy metals onto SC/AL composite was endothermic and spontaneous in nature. The adsorption capacity of developed adsorbent could still reach relatively 85% of the original one after completing fifth cycle. Therefore, the reusability results of SC/AL composite were quite satisfied, making the developed adsorbent a commercially attractive and green method. Finally, in column studies, the effect of initial concentration of pollutants at pH 5.0 on the removal of heavy metal ions was investigated. The Thomas and Yoon-Nelson models provided a satisfactory explanation for the results of column data.

A review on chitosan and alginate-based microcapsules: Mechanism and applications in drug delivery systems

Natural polymers, like chitosan and alginate have potential of appearance, as well as the changes and handling necessary to make it acceptable vehicle for the controlled release of medicines and biomolecules. Microcapsules are characterized as micrometer-sized particulate that can be employed to store chemicals within them. In the present review, we have discussed various advantages, components of microcapsules, release mechanisms, preparation methods, and their applications in drug delivery systems. The preparation methods exhibited strong encapsulation effectiveness and may be used in a wide range of pharmaceutical and biomedical applications. The major advantages of using the microencapsulation technique are, sustained and controlled delivery of drugs, drug targeting, improvement of shelf life, stabilization, immobilization of enzymes and microorganisms. As new biomaterials are developed for the body, they are better suited to the development of pharmaceutical systems than traditional pharmaceuticals because they are more reliable, biocompatible, biodegradable, and nontoxic. Furthermore, the designed microcapsules had been capable of shielding the essential components from hostile environments. More advanced techniques could be developed in the future to facilitate the formulation and applications of microcapsules and working with the pharmaceutical and medical industries.

Effect of sodium alginate-gelatin-polyvinyl pyrrolidone microspheres on cucumber plants, soil, and microbial communities under lead stress

Lead is highly persistent and toxic in soil, hindering plant growth. Microspheres are a novel, functional, and slow-release preparation commonly used for controlled release of agricultural chemicals. However, their application in the remediation of Pb-contaminated soil has not been studied; furthermore, the remediation mechanism involved has not been systematically assessed. Herein, we evaluated the Pb stress mitigation ability of sodium alginate-gelatin-polyvinyl pyrrolidone composite microspheres. Microspheres effectively attenuated the Pb toxic effect on cucumber seedlings. Furthermore, they boosted cucumber growth, increased peroxidase activity, and chlorophyll content, while reducing malondialdehyde content in leaves. Microspheres promoted Pb enrichment in cucumber, especially in roots (about 4.5 times). They also improved soil physicochemical properties, promoted enzyme activity, and increased soil available Pb concentration in the short term. In addition, microspheres selectively enriched functional (heavy metal-tolerating and plant growth promoting) bacteria to adapt to and resist Pb stress by improving soil properties and nutrients. These results indicated that even a small amount (0.025-0.3 %) of microspheres can significantly reduce the adverse effects of Pb on plants, soil, and bacterial communities. Composite microspheres have shown great value in Pb remediation, and their application potential in phytoremediation is also worth evaluating to expand the application.

Adsorptive removal of heavy metals and organic dyes by sodium alginate/coffee waste composite hydrogel

Heavy metals and dyes used in technological applications have a detrimental influence on human health and the environment. The most used methods for removing pollutants depend on high-cost materials. Therefore, this research was conducted on cost-effective alternatives derived from natural resources and food waste. Herein, we designed a composite hydrogel based on sodium alginate/coffee waste (Alg/coffee) as adsorbent for the removal of organic and inorganic pollutants from aquatic solutions. The selectivity study displayed that Alg/coffee is more effective in adsorbing Pb(II) and acridine orange dye (AO). Adsorption of Pb(II) and AO was studied at concentration range of 0-170 mgL-1 and 0-40 mgL-1. Adsorption data of Pb(II) and AO reveals their fitting to Langmuir-isotherm and pseudo-second-order-kinetic models. The findings demonstrated that Alg/coffee hydrogel are more effective than coffee powder itself with an adsorption (%) approaching 98.44 % of Pb(II) and 80.53 % of AO. Real sample analysis reveals the efficiency of Alg/coffee hydrogel beads in Pb(II) adsorption. The adsorption cycle was examined four times providing high efficiency toward Pb(II) and AO. Desorption of Pb(II) and AO was easily performed using HCl eluent. Thus, Alg/coffee hydrogel beads could be promising adsorbent for the removal of organic and inorganic pollutants.