Development of a novel dry powder inhalation formulation for the delivery of rivastigmine hydrogen tartrate

Chitosan/bovine serum albumin layer-by-layer assembled particles for non-invasive inhaled drug delivery to the lungs

Layer-by-Layer (LbL) assembly of polyelectrolytes on a solid core particle is a well-established technique used to deliver drugs, proteins, regenerative medicines, combinatorial therapy, etc. It is a multifunctional delivery system which can be engineered using various core template particles and coating polymers. This study reports the development and in-vitro evaluation of LbL assembled particles for non-invasive inhaled delivery to the lungs. The LbL assembled particles were prepared by successively coating polyelectrolyte macromolecules, glycol chitosan and bovine serum albumin on 0.5- and 4.5-μm polystyrene particles. The LbL assembly of polyelectrolytes was confirmed by reversible change in zeta potential and sequential increase in the particle size after accumulation of the layer. The prepared LbL particles were further assessed for aerodynamic properties using two distinct nebulizers, and toxicity assessment in normal lung cells. The in-vitro aerosolization study performed using next generation impactor coupled with Pari LC Plus and Aeroeclipse nebulizer showed that both the LbL assembled 0.5 and 4.5-μm particles had MMAD <5 μm confirming suitable aerodynamic properties for non-invasive lung delivery. The in-vitro cytotoxicity, and TEER integrity following treatment with the LbL assembled particles in normal lung epithelial and fibroblasts showed no significant cytotoxicity rendering the LbL assembled particles safe. This study extends the efficiency of LbL assembled particles for novel applications towards delivery of small and large molecules into the lungs.

Dual engine-driven bionic microneedles for early intervention and prolonged treatment of Alzheimer's disease

The microneedle (MN) delivery system presents an attractive administration route for patients with Alzheimer's disease (AD). However, the passive drug delivery mode and low drug loading of MNs often result in unsatisfactory therapeutic efficiency. To address these dilemmas, we developed dual engine-drive bionic MNs for robust AD treatment. Specifically, free rivastigmine (RVT) and RVT particles were co-loaded within the MNs to construct the valve and chambers of the guava, respectively, which can serve as an active engine to promote drug permeation by generating capillary force. K2CO3 and citric acid were introduced as a pneumatic engine into the MNs to promote the permeation of free RVT into deeper skin layers for early intervention in AD. Further, the RVT particles served as a drug depot to provide continuous drug release for prolonged AD treatment. Compared with free RVT-loaded MNs, the dual engine-driven bionic MNs showed an increase in drug loading, cumulative transdermal permeability, and normalized bioavailability of approximately 40%, 22%, and 49%, respectively. Pharmacodynamic studies further confirmed that the dual engine-driven bionic MNs were most effective in restoring memory and recognition functions in mice with short-term memory dysfunction. Therefore, the dual engine-driven bionic MNs hold great promise for highly efficient AD treatment.

Intramuscularly Administered PLGA Microparticles for Sustained Release of Rivastigmine: In Vitro, In Vivo and Histological Evaluation

Rivastigmine is an acetylcholinesterase (AchE) and butyrylcholinesterase (BchE) inhibitor drug approved by the US Food and Drug Administration (FDA) for the treatment of mild to moderate dementia of Alzheimer's type. However, its first-pass metabolism and gastrointestinal side effects negatively affect the tolerability and efficacy of oral therapy. These adverse effects could be avoided with the use of a sustained -release formulation as an intramuscular (IM) administration system. The objective of this work was to develop polylactic co-glycolic acid (PLGA) microparticles for the sustained release of rivastigmine and to evaluate its stability during storage, tissue tolerance, in vitro release, and in vivo pharmacokinetics after its IM administration. The microparticles were made by the solvent evaporation emulsion method. A series of formulation parameters (the type of polymer used, the amount of polymer used, the initial amount of rivastigmine, and the volume of PVA 0.1% w/v) were studied to achieve an encapsulation efficiency (EE) and a rivastigmine load of 54.8 ± 0.9% and 3.3 ± 0.1%, respectively. The microparticles, whose size was 56.1 ± 2.8 μm, had a spherical shape and a smooth surface. FT-IR analysis showed that there is no chemical interaction between rivastigmine and the polymer. PLGA microparticles maintain rivastigmine retained and stable under normal (5 ± 3 °C) and accelerated storage (25 ± 2 °C and 60 ± 5 % RH) conditions for at least 6 months. The microparticles behaved as a sustained release system both in vitro and in vivo compared to non-encapsulated rivastigmine. The IM administration of the formulation in rats did not produce significant tissue damage. However, it is necessary to reproduce the experiments with multiple doses to rule out a negative effect in terms of tolerability in chronic treatment. To the best of our knowledge, this study is the only one that has obtained the sustained release of rivastigmine from PLGA microparticles after IM administration in an in vivo model.

Development of Large Hollow Particles for Pulmonary Delivery of Cyclosporine A

The purpose of this study was to prepare large hollow particles (LHPs) by spray drying for pulmonary delivery of cyclosporine A (CsA), using L-Leucine (LEU) and hydroxypropyl methylcellulose (HPMC) as excipients and ammonium bicarbonate (AB) as a porogen. The prepared LHPs were spherical particles composed of both CsA and LEU on the surface and HPMC on the inner layer. The formulation of CsA-LEU-0.8HPMC-AB as typical LHPs showed excellent in vitro aerodynamic performance with a minimum mass median aerodynamic diameter (MMAD) of 1.15 μm. The solubility of CsA-LEU-0.8HPMC-AB was about 5.5-fold higher than that of raw CsA, and the dissolution of CsA-LEU-0.8HPMC-AB suggested that the drug was released within 1 h. The cell viability of the A549 cell line showed that CsA-LEU-0.8HPMC-AB was safe for delivering CsA to the lungs. In addition, inhalation administration of CsA-LEU-0.8HPMC-AB with the Cmax and AUC0-∞ increasing by about 2-fold and 2.8-fold compared with the oral administration of Neoral® could achieve therapeutic drug concentrations with lower systemic exposure and significantly improve the in vivo bioavailability of CsA. From these findings, the LHPs, with the advantage of avoiding alveolar macrophage clearance, could be a viable choice for delivering CsA by inhalation administration relative to oral administration.

Spray Dried Progesterone Formulations for Carrier Free Dry Powder Inhalation

Low oral absorption and extensive first pass metabolism of progesterone is reported for many oral formulations which warrants investigation into other routes of administration. It is the aim of this study to investigate the generation of inhaled formulations of progesterone though a spray drying approach with a focus on how spray drying impacts the physicochemical properties of progesterone. Formulations of progesterone with L-leucine and hydroxypropyl methylcellulose acetate succinate (HPMCAS) are reported to this aim. X-ray diffraction, spectroscopy and thermal analysis were used to characterise these formulations and confirmed that progesterone crystallises as the Form II polymorph during spray drying regardless of the solvent used. The resultant formulations showed higher aqueous solubility than progesterone Form I starting material and the addition of HPMCAS was shown to temporarily enable a supersaturated state. Thermal analysis was used to show that the Form II polymorph was sensitive to transformation to Form I during heating. The addition of L-leucine to the formulations reduced the temperature for the polymorphic transformation by ∼10 °C. However, when HPMCAS was added to the formulation, the Form II polymorph was prevented from transforming to the Form I polymorph. Cascade impaction was used to determine the aerosol performance of the spray dried powders and showed promising lung deposition profiles (mass median aerodynamic diameter 5 µm) with significant variation depending on the organic solvent used and the ratio of organic to aqueous phase in the feedstock. However, further optimisation of formulations was required to direct more progesterone into the alveolar regions. The addition of HPMCAS was seen to increase the alveolar deposition and therefore formed a formulation with a lower fine particle fraction and mass median aerodynamic diameter. The most suitable formulation for inhalation was formed from a 50:50 acetone:water destockck and showed an ED, FPF and FPD of 81.7%, 44.5% and 7.3 mg respectively. Therefore, HPMCAS is suggested as a suitable excipient to increase solubility, prevent polymorphic transformation and improve inhalation properties of spray dried progesterone formulations. This study highlights the use of spray drying to form inhalable progesterone powders with higher solubility which may broaden the application of this medicine.

Corrugated surface microparticles with chitosan and levofloxacin for improved aerodynamic performance

Corrugated surface microparticles comprising levofloxacin (LEV), chitosan and organic acid were prepared using the 3-combo spray drying method. The amount and the boiling point of the organic acid affected the degree of roughness. In this study, we tried to improve the aerodynamic performance and increase aerosolization by corrugated surface microparticle for lung drug delivery efficiency as dry powder inhaler. HMP175 L20 prepared with 175 mmol propionic acid solution was corrugated more than HMF175 L20 prepared with 175 mmol formic acid solution. The ACI and PIV results showed a significant increase in aerodynamic performance of corrugated microparticles. The FPF value of HMP175 L20 was 41.3% ± 3.9% compared with 25.6% ± 7.7% of HMF175 L20. Corrugated microparticles also showed better aerosolization, decreased x-axial velocity, and variable angle. Rapid dissolution of drug formulations was observed in vivo. Low doses administered to the lungs achieved higher LEV concentrations in the lung fluid than high doses administered orally. Surface modification in the polymer-based formulation was achieved by controlling the evaporation rate and improving the inhalation efficiency of DPIs.

Drug Delivery Systems as a Strategy to Improve the Efficacy of FDA-Approved Alzheimer's Drugs

Alzheimer's disease (AD) is the most common form of dementia, with a high impact worldwide, accounting for more than 46 million cases. The continuous increase of AD demands the fast development of preventive and curative therapeutic strategies that are truly effective. The drugs approved for AD treatment are classified into acetylcholinesterase inhibitors and N-methyl-D-aspartate receptor antagonists. The therapeutic effectiveness of those drugs is hindered by their restricted access to the brain due to the blood-brain barrier, low bioavailability, and poor pharmacokinetic properties. In addition, the drugs are reported to have undesirable side effects. Several drug delivery systems (DDSs) have been widely exploited to address these issues. DDSs serve as drug carriers, combining the ability to deliver drugs locally and in a targeted manner with the ability to release them in a controlled and sustained manner. As a result, the pharmacological therapeutic effectiveness is raised, while the unwanted side effects induced by the unspecific distribution decrease. This article reviews the recently developed DDSs to increase the efficacy of Food and Drug Administration-approved AD drugs.

Manipulation of Spray-Drying Conditions to Develop an Inhalable Ivermectin Dry Powder

SARS-CoV-2, the causative agent of COVID-19, predominantly affects the respiratory tract. As a consequence, it seems intuitive to develop antiviral agents capable of targeting the virus right on its main anatomical site of replication. Ivermectin, a U.S. FDA-approved anti-parasitic drug, was originally shown to inhibit SARS-CoV-2 replication in vitro, albeit at relatively high concentrations, which is difficult to achieve in the lung. In this study, we tested the spray-drying conditions to develop an inhalable dry powder formulation that could ensure sufficient antiviral drug concentrations, which are difficult to achieve in the lungs based on the oral dosage used in clinical trials. Here, by using ivermectin as a proof-of-concept, we evaluated spray-drying conditions that could lead to the development of antivirals in an inhalable dry powder formulation, which could then be used to ensure sufficient drug concentrations in the lung. Thus, we used ivermectin in proof-of-principle experiments to evaluate our system, including physical characterization and in vitro aerosolization of prepared dry powder. The ivermectin dry powder was prepared with a mini spray-dryer (Buchi B-290), using a 23 factorial design and manipulating spray-drying conditions such as feed concentration (0.2% w/v and 0.8% w/v), inlet temperature (80 °C and 100 °C) and presence/absence of L-leucine (0% and 10%). The prepared dry powder was in the size range of 1−5 μm and amorphous in nature with wrinkle morphology. We observed a higher fine particle fraction (82.5 ± 1.4%) in high feed concentration (0.8% w/v), high inlet temperature (100 °C) and the presence of L-leucine (10% w/w). The stability study conducted for 28 days confirmed that the spray-dried powder was stable at 25 ± 2 °C/<15% RH and 25 ± 2 °C/ 53% RH. Interestingly, the ivermectin dry powder formulation inhibited SARS-CoV-2 replication in vitro with a potency similar to ivermectin solution (EC50 values of 15.8 µM and 14.1 µM, respectively), with a comparable cell toxicity profile in Calu-3 cells. In summary, we were able to manipulate the spray-drying conditions to develop an effective ivermectin inhalable dry powder. Ongoing studies based on this system will allow the development of novel formulations based on single or combinations of drugs that could be used to inhibit SARS-CoV-2 replication in the respiratory tract.

Dry Powder Formulation of Simvastatin Nanoparticles for Potential Application in Pulmonary Arterial Hypertension

It has been hypothesized that simvastatin could be used to treat pulmonary arterial hypertension (PAH). This study is intended to formulate a simvastatin nanoparticle dry powder inhalation (DPI) formulation. Simvastatin nanoparticles were prepared via an emulsification and homogenization-extrusion method, followed by spray drying of the colloidal suspension of simvastatin nanoparticles containing mannitol to get it into a respirable size. Particle size distribution, morphology, and crystallinity of the fabricated nanoparticles of the obtained microparticles for DPI formulation were assessed by dynamic light scattering (DLS), scanning electron microscopy (SEM), and X-ray diffraction pattern (XRPD), respectively. Aerosolization performance of the DPI formulation was assessed by the Next Generation Impactor (NGI) equipped with an Aerolizer^®. Simvastatin nanoparticles were around 100 nm with a very narrow size distribution (PDI = 0.105). The X-ray diffraction pattern revealed that the crystallinity of simvastatin was decreased by the spray drying procedure. Microscopic images displayed that gathered nanoparticles were in the suitable inhalable range and had the appropriate shape and surface properties for pulmonary delivery. Aerosolization assessment by the NGI indicated a suitable inhalation performance (fine particle fraction of 20%). In conclusion, the results confirmed that the spray drying technique for simvastatin can be optimized to obtain simvastatin aggregated nanoparticles without any coarse carrier to be used in DPI formulation for better deposition of the drug in the lungs for local treatment of PAH.

Inhalable cryptotanshinone spray-dried swellable microparticles for pulmonary fibrosis therapy by regulating TGF-β1/Smad3, STAT3 and SIRT3 pathways

Cryptotanshinone (CTS) is a promising therapeutic option for pulmonary fibrosis (PF). However, clinical applications of CTS are limited owing to high photosensitivity and poor oral bioavailability. Pulmonary drug delivery, especially sustained pulmonary drug delivery, is promising for local treatment of chronic lung diseases. In this study, CTS was encapsulated in an optimized chitosan/L-leucine-based swellable microparticles (SMs) system, which exhibited an appropriate aerosolization performance, sustained release and storage stability. SMs enhanced the in vitro anti-fibrosis efficacy of CTS as shown by the improved cellular uptake. The effect of PF status on in vivo fate of the pulmonary delivered drug was also assessed. Pharmacokinetics and tissue distribution of oral and pulmonary delivery CTS in bleomycin-induced PF rats were compared. Pulmonary delivery exhibited high drug concentrations in pulmonary lesion areas, with reduced exposure to blood and non-targeted tissues after administration at a significantly lower dose compared with oral delivery. Moreover, PF pathological status enhanced activity of SMs, implying that pulmonary delivery was highly effective for PF treatment. Compared to oral delivery, Inhaled SMs showed comparable or even better efficacies at approximately 60-fold low dose compared with oral delivery. A sustained efficacy was observed under a prolonged administration interval (corresponding to half the total dose). Inhalation safety of SMs was established, and important mechanism-related signaling pathways against PF were investigated in vitro and in vivo. In summary, the findings showed that the developed CTS-loaded sustained pulmonary delivery system is a safe and effective strategy for chronic PF treatment.

Polysorbate-coated mesoporous silica nanoparticles as an efficient carrier for improved rivastigmine brain delivery

Targeted delivery of neurological therapeutic to the brain has been attracting more and more attention to the treatment of central nervous system (CNS) diseases. Nonetheless, the main obstacle in this road map is the existence of a blood-brain barrier (BBB) which limits the penetration efficiency of most CNS drugs into the brain parenchyma. This present investigation describes a facile synthetic strategy to prepare a highly biocompatible calcium-doped mesoporous silica nanoparticles (MSNs) functionalized by polysorbate-80 (PS) as targeting ligand to deliver rivastigmine (RV) into the brain via crossing the BBB. The developed nanosystem was characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), Zeta potential, and N₂-adsorption-desorption analysis. In vitro hemolysis studies were carried out to confirm the biocompatibility of the nanocarriers. Our in vivo studies in an animal model of rats showed that the RV-loaded nanosystem was able to enhance the brain-to-plasma concentration ratio, brain uptake clearance, and plasma elimination half-life of the drug compared to the free one drug following intravenous (IV) administration. The results revealed that functionalization of MSNs by PS is crucial to deliver RV into the brain, suggesting PS-functionalized MSNs could be an effective carrier to deliver RV to the brain while overcoming BBB.

A Design of Experiment Approach to Optimize Spray-Dried Powders Containing Pseudomonas aeruginosaPodoviridae and Myoviridae Bacteriophages

In the present study, we evaluated the effect of spray-drying formulations and operating parameters of a laboratory-scale spray-dryer on the characteristics of spray-dried powders containing two Pseudomonas aeruginosa bacteriophages exhibiting different morphotypes: a podovirus (LUZ19) and a myovirus (14-1). We optimized the production process for bacteriophage-loaded powders, with an emphasis on long-term storage under ICH (international conference on harmonization) conditions. D-trehalose-/L-isoleucine-containing bacteriophage mixtures were spray-dried from aqueous solutions using a Büchi Mini Spray-dryer B-290 (Flawil, Switzerland). A response surface methodology was used for the optimization of the spray-drying process, with the following as-evaluated parameters: Inlet temperature, spray gas flow rate, and the D-trehalose/L-isoleucine ratio. The dried powders were characterized in terms of yield, residual moisture content, and bacteriophage lytic activity. L-isoleucine has demonstrated a positive impact on the activity of LUZ19, but a negative impact on 14-1. We observed a negligible impact of the inlet temperature and a positive correlation of the spray gas flow rate with bacteriophage activity. After optimization, we were able to obtain dry powder preparations of both bacteriophages, which were stable for a minimum of one year under different ICH storage conditions (up to and including 40 °C and 75% relative humidity).

Engineering of levodopa inhalable microparticles in combination with leucine and dipalmitoylphosphatidylcholine by spray drying technique

The aim of this work was to study the effect of concomitant use of leucine and dipalmitoylphosphatidylcholine, in different ratios, on aerosolization performance of levodopa. Three-component formulations were selected based on a central composite design using percentages of leucine and dipalmitoylphosphatidylcholine as the independent variables. Particle size, surface roughness index, surface phosphorus and fine particle fraction were considered as dependent variables in the model. The spray dried samples were also characterized to determine their particle shape and solid state nature. levodopa was spray dried with 10-40% w/w of the excipients to prepare two- or three-component formulations. A crystalline nature was determined for levodopa in all samples spray dried from water:ethanol (30:70 v/v). Roughness in surface of the processed particles increased with increasing total concentration of the excipients, specially above 25% w/w. Analysis of phosphorus on the surface demonstrated that three-component formulations prepared with combination of 12.5% w/w leucine had the highest amount of dipalmitoylphosphatidylcholine in the surface, regardless of its percentage used in the initial feed. A combination of 12.43% w/w of leucine and 9.80% w/w of dipalmitoylphosphatidylcholine used in formulation exhibited the highest fine particle fraction (72.63%). It can be concluded that spray drying of levodopa with a suitable combination of both excipients leads to production of a three-component formulation of crystalline levodopa, with an aerosolization performance which is significantly higher than two-component formulations composed of the drug with either leucine or dipalmitoylphosphatidylcholine.

Stability and In Vitro Aerodynamic Studies of Inhalation Powders Containing Ciprofloxacin Hydrochloride Applying Different DPI Capsule Types

In the case of capsule-based dry powder inhalation systems (DPIs), the selection of the appropriate capsule is important. The use of gelatin, gelatin-PEG, and HPMC capsules has become widespread in marketed capsule-based DPIs. We aimed to perform a stability test according to the ICH guideline in the above-mentioned three capsule types. The results of the novel combined formulated microcomposite were more favorable than those of the carrier-free formulation for all capsule types. The use of HPMC capsules results in the greatest stability and thus the best in vitro aerodynamic results for both DPI powders after six months. This can be explained by the fact that the residual solvent content (RSC) of the capsules differs. Under the applied conditions the RSC of the HPMC capsule decreased the least and remained within the optimal range, thus becoming less fragmented, which was reflected in the RSC, structure and morphology of the particles, as well as in the in vitro aerodynamic results (there was a difference of approximately 10% in the lung deposition results). During pharmaceutical dosage form developments, emphasis should be placed in the case of DPIs on determining which capsule type will be used for specific formulations.

The effect of ethanol on the habit and in vitro aerodynamic results of dry powder inhalation formulations containing ciprofloxacin hydrochloride

In the case of dry powder inhalation systems (DPIs), the development of carrier-free formulations has gained increased attention. Thereby, spray-drying is a promising technology and is widely used to produce carrier-free DPIs. Numerous works have been published about the co-spray-drying of active ingredients with various solid excipients and their effect on the physicochemical characteristics and aerodynamic properties of the formulations. However, only a few studies have been reported about the role of the solvents used in the stock solutions of spray-dried formulations. In the present work, DPI microcomposites containing ciprofloxacin hydrochloride were prepared by spray-drying in the presence of different ethanol concentrations. The work expresses the roughness, depth and width of the dimples for particle size as a novel calculation possibility, and as a correlation between the MMAD/D_0.5 ratio and correlating it with cohesion work, these new terms and correlations have not been published – to the best of our knowledge – which has resulted in gap-filling findings. As a result, different proportions of solvent mixtures could be interpreted and placed in a new perspective, in which the influence of different concentrations of ethanol on the habit of the DPI formulations, and thus on in vitro aerodynamic results. Based on these, it became clear why we obtained the best in vitro aerodynamic results for DPI formulation containing 30% ethanol in the stock solution.

Leucine as an excipient in spray dried powder for inhalation

Leucine is a promising excipient with several applications in the development of inhalable spray-dried powder of high- and low-dose drugs. The addition of leucine has exhibited significant enhancing effects on the aerosolization and physical stability of the produced particles. Here, we focus not only on the applications of leucine in inhalable spray-drying powders, but also on the underlying mechanisms by which the formulation and processing parameters dictate the behavior of leucine during the drying process and, therefore, its functionalities within the dried powder. Additionally, we highlight the current regulatory status of leucine. Such insights are important for more efficient utilization of leucine in the future, both for dry powder inhaler formulations and other pharmaceutical applications.

A quantitative approach to predicting lung deposition profiles of pharmaceutical powder aerosols

Dry powder inhalers (DPI) are widely used systems for pulmonary delivery of therapeutics. The inhalation performance of DPIs is influenced by formulation features, inhaler device and inhalation pattern. The current review presents the affecting factors with great focus on powder characteristics which include particle size, shape, surface, density, hygroscopicity and crystallinity. The properties of a formulation are greatly influenced by a number of physicochemical factors of drug and added excipients. Since available particle engineering techniques result in particles with a set of modifications, it is difficult to distinguish the effect of an individual feature on powder deposition behavior. This necessitates developing a predictive model capable of describing all influential factors on dry powder inhaler delivery. Therefore, in the current study, a model was constructed to correlate the inhaler device properties, inhalation flow rate, particle characteristics and drug/excipient physicochemical properties with the resultant fine particle fraction. The r² value of established correlation was 0.74 indicating 86% variability in FPF values is explained by the model with the mean absolute errors of 0.22 for the predicted values. The authors believe that this model is capable of predicting the lung deposition pattern of a formulation with an acceptable precision when the type of inhaler device, inhalation flow rate, physicochemical behavior of active and inactive ingredients and the particle characteristics of DPI formulations are considered.

Formulation and optimization of sildenafil citrate-loaded PLGA large porous microparticles using spray freeze-drying technique: A factorial design and in-vivo pharmacokinetic study

The oral administration of sildenafil citrate (SC) for the treatment of pulmonary arterial hypertension is associated with several drawbacks. The study aimed to design and formulate SC-loaded inhalable poly (lactic-co-glycolic acid) [PLGA] large porous microparticles (LPMs) for pulmonary delivery. A factorial design was used to study the effect of the composition of LPMs on physicochemical properties. The study also evaluated the effect of glucose and L-leucine concentration on the formulation. The developed LPMs demonstrated an acceptable yield% (≤48%), large geometric particle size (>5µm) with a spherical and porous surface, and sustained drug release (up to 48 h). Increasing the concentration of poly(ethyleneimine) from 0.5% to 1% in SC-loaded LPMs led to an increase in entrapment efficiency from ~3.02% to ~94.48%. The optimum LPMs showed adequate aerodynamic properties with a 97.68 ± 1.07% recovery, 25.33 ± 3.32% fine particle fraction, and low cytotoxicity. Intratracheal administration of LPMs demonstrated significantly higher lung deposition, systemic bioavailability, and longer retention time (p < 0.05) compared to orally administered Viagra® tablets. The study concluded that SC-loaded LPMs could provide better therapeutic efficacy, reduced dosing frequency, and enhanced patient compliance.

Pulmonary Targeting of Inhalable Moxifloxacin Microspheres for Effective Management of Tuberculosis

In the present study, the objective was to attain a localized lung delivery of an anti-tubercular fluoroquinolone, moxifloxacin (MXF), targeting the alveolar macrophages through a non-invasive pulmonary route using inhalable microspheres as a dry powder inhaler approach. MXF-loaded poly (lactic-co-glycolic acid) (PLGA) microspheres (MXF-PLGA-MSs) were fabricated by solvent evaporation technique and optimized by using a central composite statistical design. The morphology and particle size, as well as the flowability of the optimized microspheres, were characterized. In addition, the aerosolization performance of the optimized formula was inspected using an Andersen cascade impactor. Furthermore, in vivo fate following intrapulmonary administration of the optimized formula was evaluated. The optimized MXF-PLGA-MSs were spherical in shape with a particle size of 3.16 µm, drug loading of 21.98% and entrapment efficiency of 78.0%. The optimized formula showed a mass median aerodynamic diameter (MMAD) of 2.85 ± 1.04 µm with a favorable fine particle fraction of 72.77 ± 1.73%, suggesting that the powders were suitable for inhalation. Most importantly, in vivo studies revealed that optimized MXF-PLGA-MSs preferentially accumulated in lung tissue as manifested by a two-fold increase in the area under the curve AUC_0–24h, compared to plain drug. In addition, optimized MXF-PLGA-MS sustained drug residence in the lung for up to 24 h following inhalation, compared to plain drug. In conclusion, inhalable microspheres of MXF could be a promising therapeutic approach that might aid in the effective eradiation of tuberculosis along with improving patient adherence to the treatment.

Development of solid lipid microparticles by melt-emulsification/spray-drying processes as carriers for pulmonary drug delivery

The aim of this study was to optimize the parameters of the complex melt-emulsification process coupled with the spray-drying, in order to maintain the balance between solid lipid microparticles (SLMs) powders aerodynamic performance and salbutamol sulfate release rate. Quality target product profile was identified and risk management and principal component analysis were used to guide formulation development. Obtained dry powders for inhalation (DPIs) were evaluated in terms of SLMs size distribution, morphology, true density, drug content, solid state characterization studies, in vitro aerosol performance and in vitro drug release. SLMs micrographs indicated spherical, porous particles. Selected powders showed satisfactory aerosol performance with a mean mass aerodynamic diameter of around 3 μm and acceptable fine particle fraction (FPF). Addition of trehalose positively affected SLMs aerodynamic properties. The results of in vitro dissolution testing indicated that salbutamol sulfate release from the tested SLMs formulations was modified, in comparison to the raw drug release. In conclusion, SLMs in a form of DPIs were successfully developed and numerous factors that affects SLMs properties were identified in this study. Further research is required for full understanding of each factor's influence on SLMs properties and optimization of DPIs with maximized FPFs.

Celecoxib Loaded In-Situ Provesicular Powder and Its In-Vitro Cytotoxic Effect for Cancer Therapy: Fabrication, Characterization, Optimization and Pharmacokinetic Evaluation

INTRODUCTION

Several recent studies have shown that the role of cyclooxygenase 2 (COX-2) in carcinogenesis has become more evident. It affects angiogenesis, apoptosis, and invasion, and plays a key role in the production of carcinogens. It has also been reported that COX-2 inhibitors such as celecoxib (CLX) might play an effective role in preventing cancer formation and progression. Formulation of CLX into nanovesicles is a promising technique to improve its bioavailability and anticancer efficacy.

AIM

The aim of this study is to optimize and evaluate the anticancer efficacy of CLX-loaded in-situ provesicular powder composed of surfactants and fatty alcohol-based novel nanovesicles in-vitro and determine its pharmacokinetic parameters in-vivo.

METHODS

The novel provesicular powders were prepared by the slurry method and optimized by 3² full factorial design using the desirability function.

RESULTS

Small mean particle size was achieved by the formed vesicles with value of 351.7 ± 1.76 nm and high entrapment efficacy of CLX in the formed vesicles of 97.53 ± 0.84%. Solid state characterization of the optimized formulation showed that the powder was free flowing, showed no incompatibilities between drug and excipients and showed smooth texture. The cytotoxic study of the optimized formula on HCT-116, HepG-2, A-549, PC-3 and MCF-7 cell lines showed significant increase in activity of CLX compared to its free form. The pharmacokinetic study on albino rabbits after oral administration showed significant increase in the area under the curve (AUC)_{0-24 h} and significantly higher oral relative bioavailability of the optimized formulation compared to Celebrex^® 100 mg market product (p < 0.05).

CONCLUSION

All findings of this study suggest the potential improvement of efficacy and bioavailability of CLX when formulated in the form of in-situ provesicular powder composed of surfactants and fatty alcohol-based novel nanovesicles for its repositioned use as an anticancer agent.

The Use of a Three-Fluid Atomising Nozzle in the Production of Spray-Dried Theophylline/Salbutamol Sulphate Powders Intended for Pulmonary Delivery

The aim of this study was to investigate the use of a three-fluid atomising nozzle in a lab-scale spray dryer for the production of dry powders intended for pulmonary delivery. Powders were composed of salbutamol sulphate and theophylline in different weight ratios. The three-fluid nozzle technology enabled powders containing a high theophylline content to be obtained, overcoming the problems associated with its relatively low solubility, by pumping two separate feed solutions (containing the two different active pharmaceutical ingredients (APIs)) into the spray dryer via two separate nozzle channels at different feed rates. The final spray-dried products were characterized in terms of morphology, solid-state properties and aerosolization performance, and were compared with an equivalent formulation prepared using a standard two-fluid atomising nozzle. Results confirmed that most of the powders made using the three-fluid atomising nozzle met the required standards for a dry powder inhaler formulation in terms of physical characteristics; however, aerosolization characteristics require improvement if the powders are to be considered suitable for pulmonary delivery.

Effects of a novel roflumilast and formoterol fumarate dry powder inhaler formulation in experimental allergic asthma

In this study we aimed to develop a roflumilast (R) and formoterol fumarate (F) dry powder inhaler formulation (DPI) incorporating HPβCD by spray drying and evaluated if it attenuates the inflammatory process and improves lung function in a murine model of ovalbumin induced allergic asthma. The DPI was characterized by powder X-ray diffraction, thermal analysis, scanning electron microscopy, particle size, density, specific surface area and dynamic vapor sorption analyses. In vitro deposition studies were performed using a NGI, while transepithelial permeability and in vivo effects on lung mechanics and inflammation in a model of allergic asthma were also assessed. The R:F formulation was amorphous with high glass transition temperatures, comprised of wrinkled particles, had low bulk and tapped densities, high surface area, suitable particle size for pulmonary delivery and exhibited no recrystallization even at high relative humidities. MMAD were statistically similar of 4.22 ± 0.19 and 4.32 ± 0.13 µm for F and R, respectively. Fine particle fractions (<5 µm) were of more than 50% of the emitted dose. The R:F formulation led to reduced eosinophil infiltration and airway collagen fiber content, yielding decreased airway hyperresponsiveness. In the current asthma model, the R:F formulation combination decreased inflammation and remodeling, thus improving lung mechanics.

Development of an Innovative, Carrier-Based Dry Powder Inhalation Formulation Containing Spray-Dried Meloxicam Potassium to Improve the In Vitro and In Silico Aerodynamic Properties

Most of the marketed dry powder inhalation (DPI) products are traditional, carrier-based formulations with low drug concentrations deposited in the lung. However, due to their advantageous properties, their development has become justified. In our present work, we developed an innovative, carrier-based DPI system, which is an interactive physical blend of a surface-modified carrier and a spray-dried drug with suitable shape and size for pulmonary application. Meloxicam potassium, a nonsteroidal anti-inflammatory drug (NSAID), was used as an active ingredient due to its local anti-inflammatory effect and ability to decrease the progression of cystic fibrosis (CF) and chronic obstructive pulmonary disease (COPD). The results of the in vitro and in silico investigations showed high lung deposition in the case of this new formulation, confirming that the interparticle interactions were changed favorably.

Development of Sustained Release Oseltamivir Phosphate Dry Powder Inhaler: In-Vitro Characterization and In-Vivo Toxicological Studies

BACKGROUND

Oseltamivir Phosphate (OP) is an ethyl ester prodrug prescribed for the treatment of influenza virus infection. Current marketed formulations of OP have been observed to be supplemented with an adverse effect during post-marketing surveillance. These prerequisites are sufficed by developing a sustained release Dry Powder for Inhalation (DPI).

OBJECTIVE

The objective of the present study was to develop OP-DPI by an innovative formulation approach comprising of Immediate (IR) and Sustained (SR) Release portions.

METHODS

DPI formulation comprising IR and SR portions were prepared by spray drying technique using Hydroxy Propyl Methyl Cellulose (HPMC) as the rate-controlling polymer for SR portion. The spray-dried product was further characterized for various pharmaco-technical, in-vitro and in-vivo parameters.

RESULTS

OP-DPI showed a burst release of 49% within 15 min further sustaining the drug release up to 9 hrs. The in-vitro aerodynamic performance of OP-DPI showed maximum deposition at stage 3 and Fine Particle Dose (FPD) of 1.08 mg indicating deposition in the upper respiratory tract. Solid-state characterization by DSC and XRD indicated the partial amorphization of OP due to spray drying. In-vivo toxicological examination revealed no sign of inflammation, indicating the safety of the developed formulation. Accelerated stability study as per ICH guidelines displayed no significant change in the solid-state characterization and drug-related performance of OP-DPI.

CONCLUSION

Prepared novel and scalable OP-DPI may have the potential to overcome the problems associated with existing marketed dosage forms of OP. Further, localized drug delivery of the antiviral drug through the pulmonary route might be clinically beneficial in controlling the viral proliferation.

Naringenin-Loaded Dipalmitoylphosphatidylcholine Phytosome Dry Powders for Inhaled Treatment of Acute Lung Injury

Background: Acute lung injury is a severe respiratory disorder characterized by overwhelming lung inflammation. Dipalmitoylphosphatidylcholine (DPPC) is the major lipid component of pulmonary surfactant, which here acts as a carrier delivery system for drugs, while also preserving surface tension in the lung. The clinical development of naringenin (NG) is limited by its low solubility and bioavailability. Methods: Novel NG-loaded DPPC phytosomes for dry powder inhalation (NPDPIs) were prepared by solvent evaporation and a freeze-drying method. The particle size, electric potential, in vitro release, and lung deposition were characterized. A rat model of acute lung injury was established and used for pharmacodynamic evaluations. Results: A mixture of NG/DPPC 1:2 (w/w) formed stable phytosomes with the addition of appropriate ethanol. The phytosomes had high complexation efficiency (92.1% ± 1.87%) with NG, a small mean size (150.8 ± 6.9 nm), and a high zeta potential (20.97 ± 0.55 mV). NPDPIs composed of mannitol/DPPC/NG (4:2:1, w/w/w) presented a satisfactory appearance, good fluidity, quick reconstitution to naringenin phytosomes (NGPs), and small (167.2 nm) reconstituted NGPs. The aerodynamic diameter (12.48 μm) and fine particle fraction (23.90%) were suitable for pulmonary delivery by inhalation. The in vivo NPDPIs demonstrated efficacy in a rat model of acute lung injury. NPDPIs significantly inhibited the phosphorylation of P38 in the mitogen-activated protein kinase pathway and suppressed oxidative stress. Surprisingly, the DPPC vehicle exhibited potential effects against acute lung injury by protecting respiratory function. Conclusions: NPDPIs were developed for sustained drug release, promoting pulmonary bioavailability of drug and protecting against acid-induced acute lung injury in rats by pulmonary delivery. NPDPIs are a promising dry powder inhaler for clinical application in acute lung injury.

Influence of Composition and Spray-Drying Process Parameters on Carrier-Free DPI Properties and Behaviors in the Lung: A review

Although dry powder inhalers (DPIs) have attracted great interest compared to nebulizers and metered-dose inhalers (MDIs), drug deposition in the deep lung is still insufficient to enhance therapeutic activity. Indeed, it is estimated that only 10–15% of the drug reaches the deep lung while 20% of the drug is lost in the oropharyngeal sphere and 65% is not released from the carrier. The potentiality of the powders to disperse in the air during the patient’s inhalation, the aerosolization, should be optimized. To do so, new strategies, in addition to classical lactose-carrier, have emerged. The lung deposition of carrier-free particles, mainly produced by spray drying, is higher due to non-interparticulate forces between the carrier and drug, as well as better powder uniformity and aerosolization. Moreover, the association of two or three active ingredients within the same powder seems easier. This review is focused on a new type of carrier-free particles which are characterized by a sugar-based core encompassed by a corrugated shell layer produced by spray drying. All excipients used to produce such particles are dissected and their physico-chemical properties (Péclet number, glass transition temperature) are put in relation with the lung deposition ability of powders. The importance of spray-drying parameters on powders’ properties and behaviors is also evaluated. Special attention is given to the relation between the morphology (characterized by a corrugated surface) and lung deposition performance. The understanding of the closed relation between particle material composition and spray-drying process parameters, impacting the final powder properties, could help in the development of promising DPI systems suitable for local or systemic drug delivery.

Physical stability of dry powder inhaler formulations

Introduction: Dry powder inhalers (DPIs) are popular for pulmonary drug delivery. Various techniques have been employed to produce inhalation drug particles and improve the delivery efficiency of DPI formulations. Physical stability of these DPI formulations is critical to ensure the delivery of a reproducible dose to the airways over the shelf-life.Areas covered: This review focuses on the impact of solid-state stability on aerosolization performance of DPI drug particles manufactured by powder production approaches and particle-engineering techniques. It also highlights the different analytical tools that can be used to characterize the physical instability originating from production and storage.Expert opinion: A majority of the DPI literature focuses on the effects of physico-chemical properties such as size, morphology, and density on aerosolization. While little has been reported on the physical stability, particularly the stability of engineered drug particles for use in DPIs. Literature data have shown that different particle-engineering methods and storage conditions may cause physical instability of dry powders for inhalation and can significantly change the aerosol performance. A systematic examination of physical instability mechanisms in DPI formulations is necessary during formulation development in order to select the optimum formulation with satisfactory stability. In addition, the use of appropriate characterization tools is critical to detect and understand physical instability during the development of DPI formulations.

In-vitro and in-vivo respiratory deposition of a developed metered dose inhaler formulation of an anti-migraine drug

Enhancement of zolmitriptan bioavailability through development of micronized zolmitriptan pressurized metered dose inhaler (MDI) as an alternative to its traditional drug delivery systems. A reversed phase HPLC method for zolmitriptan determination was developed and evaluated. Micronized zolmitriptan MDI formulations were prepared using two different propellants. The prepared formulations were evaluated for mean shot weight, drug content, and leakage rate in addition to in-vitro deposition using next generation impactor where mass median aerodynamic diameter (MMAD), geometric standard deviation (GSD), fine particle dose, fine particle fraction (FPF), emitted dose (ED), and dispersibility were determined. The selected formulation was evaluated for in-vivo bronchial absorption in rats. The physicochemical characters of the prepared formulations were found to be dependent mainly on the vapor pressure of the used propellant. MDI formulation prepared with HFA 134a propellant was found to have the lowest MMAD (3.47 ± 0.65) with GSD of 2.3 ± 0.4. It also had the highest FPF (41.9), ED (89.26 ± 2.35) with dispersibility of 46.9%. This formulation, when applied to rats, resulted in faster Tmax (27 ± 5 min) with higher Cmax (1236 ± 116 ng/mL) and AUC(0-12) (3375 ± 482 ng/mL·h) over the oral tablet. Its relative bioavailability was 72.7% which was 1.25 times higher than the oral tablet relative bioavailability. Zolmitriptan MDI formulation was developed using micronized zolmitriptan powder without further modification or particle engineering. The developed formulation using HFA 134a propellant could be favorable alternative, with enhanced bioavailability, to zolmitriptan oral tablet for acute migraine treatment.

The use of hydrophobic amino acids in protecting spray dried trehalose formulations against moisture-induced changes

Trehalose is commonly used as a protein stabilizer in spray dried protein formulations delivered via the pulmonary route. Spray dried trehalose formulations are highly hygroscopic, which makes them prone to deliquescence and recrystallization when exposed to moisture, leading to impairment in aerosolization performance. The main aim of this study was to investigate and compare the effect of hydrophobic amino acids (i.e. L-leucine and L-isoleucine) in enhancing aerosolization performance and in mitigating moisture-induced changes in spray dried trehalose formulations. Trehalose was spray dried with 20-60% w/w of amino acid (i.e. L-leucine or L-isoleucine). The spray dried formulations were stored at 25 °C/50% RH for 28 days. Solid state characterization and in vitro aerosolization performance studies were performed on the spray dried formulations before and after storage. The addition of 20-60% w/w of amino acid (i.e. L-leucine or L-isoleucine) improved the emitted fractions of spray dried trehalose formulations from a dry powder inhaler. However, ≥ 40% w/w of L-leucine/L-isoleucine was needed to prevent recrystallization of trehalose in the formulations when exposed to 25 °C/50% RH for 28 days. X-ray photoelectron spectroscopy (XPS) demonstrated that samples with 40-60% w/w L-isoleucine had more amino acid on the surfaces of the particles compared to their L-leucine counterparts. This may explain the greater ability of the L-isoleucine (40-60% w/w) samples to cope with elevated humidity compared to L-leucine samples of the same concentrations, as observed in the dynamic vapour sorption (DVS) studies. In conclusion, this study demonstrated that both L-leucine and L-isoleucine were effective in enhancing aerosolization performance and mitigating moisture-induced reduction in aerosolization performance in spray dried trehalose formulations. L-isoleucine proved to be superior to L-leucine in terms of its moisture protectant effect when incorporated at the same concentration in the formulations.

Development and Characterization of a Dry Powder Formulation for Anti-Tuberculosis Drug Spectinamide 1599

PURPOSE

Human tuberculosis (TB) is a global health problem that causes nearly 2 million deaths per year. Anti-TB therapy exists, but it needs to be administered as a cocktail of antibiotics for six months. This lengthy therapy results in low patient compliance and is the main reason attributable to the emergence of multidrug-resistant (MDR) and extensively drug-resistant (XDR) strains of Mycobacterium tuberculosis.

METHODS

One alternative approach is to combine anti-TB multidrug therapy with inhalational TB therapy. The aim of this work was to develop and characterize dry powder formulations of spectinamide 1599 and ensure in vitro and in vivo delivered dose reproducibility using custom dosators.

RESULTS

Amorphous dry powders of spectinamide 1599 were successfully spray dried with mass median aerodynamic diameter (MMAD) = 2.32 ± 0.05 μm. The addition of L-leucine resulted in minor changes to the MMAD (1.69 ± 0.35 μm) but significantly improved the inhalable portion of spectinamide 1599 while maintaining amorphous qualities. Additionally, we were able to demonstrate reproducibility of dry powder administration in vitro and in vivo in mice.

CONCLUSIONS

The corresponding systemic drug exposure data indicates dose-dependent exposure in vivo in mice after dry powder intrapulmonary aerosol delivery in the dose range 15.4 - 32.8 mg/kg.

Stability test of novel combined formulated dry powder inhalation system containing antibiotic: physical characterization and in vitro-in silico lung deposition results

Objective: The aim was to study the stability of dry powder inhaler (DPI) formulations containing antibiotic with different preparation ways - carrier-based, carrier-free, and novel combined formulation - and thereby to compare their physicochemical and in vitro-in silico aerodynamical properties before and after storage. Presenting a novel combined technology in the field of DPI formulation including the carrier-based and carrier-free methods, it is the most important reason to introduce this stable formulation for the further development of DPIs. Methods: The structure, the residual solvent content, the interparticle interactions, the particle size distribution and the morphology of the samples were studied. The aerodynamic values were determined based on the cascade impactor in vitro lung model. We tested the in silico behavior of the novel combined formulated samples before and during storage. Results: The physical measurements showed that the novel combined formulated sample was the most favorable. It was found that thanks to the formulation technique and the use of magnesium stearate (MgSt) has a beneficial effect on the stability compared with the carrier-based formulation without MgSt and carrier-free formulations. The results of in vitro and in silico lung models were consistent with the physical results, so the highest deposition was found for the novel combined formulated sample during the storage. Conclusions: It can be established that after the storage a novel combined formulated DPI contained amorphous drug to have around 2.5 μm mass median aerodynamic diameter and nearly 50% fine particle fraction predicted high lung deposition in silico also.

Recyclable Fully Biobased Chitosan Adsorbents Spray-Dried in One Pot to Microscopic Size and Enhanced Adsorption Capacity

A facile one-pot spray-drying process was developed for fabrication and in situ crosslinking of chitosan microspheres to improve the adsorption capacity by microscopic design. A fully biobased nature was achieved by utilizing genipin (GP) as a crosslinking agent and chitosan-derived nanographene oxide (nGO) as a property tuner. The produced chitosan microspheres were further proven as powerful adsorbents for common wastewater contaminants such as anionic dyes and pharmaceutical contaminants, here modeled by methyl orange (MO) and diclofenac sodium (DCF). By regulating the amount of GP and nGO, as well as by controlling the process parameters including the spray-drying inlet temperature and postheat treatment, the surface morphology, size, zeta potential, and adsorption efficiency of the microspheres could be tuned accordingly. The adsorption efficiency for MO and DCF reached 98.9 and 100%, respectively. The microspheres retained high DCF adsorption efficiency after six adsorption and desorption cycles, and the recyclability was improved by the incorporated nGO. The fabricated microspheres, thus, have great potential as reusable and eco-friendly adsorbents.

A Design of Experiment (DoE) approach to optimise spray drying process conditions for the production of trehalose/leucine formulations with application in pulmonary delivery

The present study evaluates the effect of L-leucine concentration and operating parameters of a laboratory spray dryer on characteristics of trehalose dry powders, with the goal of optimizing production of these powders for inhaled drug delivery. Trehalose/L-leucine mixtures were spray dried from aqueous solution using a laboratory spray dryer. A factorial design of experiment (DoE) was undertaken and process parameters adjusted were: inlet temperature, gas flow rate, feed solution flow rate (pump setting), aspiration setting and L-leucine concentration. Resulting powders were characterised in terms of particle size, yield, residual moisture content, and glass transition temperature. Particle size was mainly influenced by gas flow rate, whereas product yield and residual moisture content were found to be primarily affected by inlet temperature and spray solution feed rate respectively. Interactions between a number of different process parameters were elucidated, as were relationships between different responses. The leucine mass ratio influenced the physical stability of powders against environmental humidity, and a high leucine concentration (30% w/w) protected amorphous trehalose from moisture induced crystallization. High weight ratio of leucine in the formulation, however, negatively impacted the aerosol performance. Thus, in terms of L-leucine inclusion in a formulation designed for pulmonary delivery, a balance needs to be found between physical stability and deposition characteristics.

A review on recent technologies for the manufacture of pulmonary drugs

This review discusses recent developments in the manufacture of inhalable dry powder formulations. Pulmonary drugs have distinct advantages compared with other drug administration routes. However, requirements of drugs properties complicate the manufacture. Control over crystallization to make particles with the desired properties in a single step is often infeasible, which calls for micronization techniques. Although spray drying produces particles in the desired size range, a stable solid state may not be attainable. Supercritical fluids may be used as a solvent or antisolvent, which significantly reduces solvent waste. Future directions include application areas such as biopharmaceuticals for dry powder inhalers and new processing strategies to improve the control over particle formation such as continuous manufacturing with in-line process analytical technologies.

Inhalation treatment of primary lung cancer using liposomal curcumin dry powder inhalers

Lung cancer is the leading cause of cancer-related deaths. Traditional chemotherapy causes serious toxicity due to the wide bodily distribution of these drugs. Curcumin is a potential anticancer agent but its low water solubility, poor bioavailability and rapid metabolism significantly limits clinical applications. Here we developed a liposomal curcumin dry powder inhaler (LCD) for inhalation treatment of primary lung cancer. LCDs were obtained from curcumin liposomes after freeze-drying. The LCDs had a mass mean aerodynamic diameter of 5.81 μm and a fine particle fraction of 46.71%, suitable for pulmonary delivery. The uptake of curcumin liposomes by human lung cancer A549 cells was markedly greater and faster than that of free curcumin. The high cytotoxicity on A549 cells and the low cytotoxicity of curcumin liposomes on normal human bronchial BEAS-2B epithelial cells yielded a high selection index partly due to increased cell apoptosis. Curcumin powders, LCDs and gemcitabine were directly sprayed into the lungs of rats with lung cancer through the trachea. LCDs showed higher anticancer effects than the other two medications with regard to pathology and the expression of many cancer-related markers including VEGF, malondialdehyde, TNF-α, caspase-3 and BCL-2. LCDs are a promising medication for inhalation treatment of lung cancer with high therapeutic efficiency.

Development of a Discriminative In Vitro Release Test for Rivastigmine Transdermal Patches Using Pharmacopeial Apparatuses: USP 5 and USP 6

The aim of this study was to develop and validate a discriminating in vitro release test to evaluate rivastigmine transdermal patches. The Exelon® Patch was chosen as a model transdermal product. The studies of in vitro release were designed to determine the impact of the official apparatus chosen (USP apparatus 5 and USP apparatus 6), the rotation speed, and the dissolution medium characteristics on the rivastigmine release profile from transdermal patches. Patches with different drug release profiles were tested in order to evaluate the discriminating power of the in vitro release test developed and validated. Variables such as the apparatus type, the dissolution medium, and the rotation speed have a significant influence on the drug release characteristics from a transdermal patch. The in vitro release methodologies using the USP apparatus 5 at 50 rpm and USP apparatus 6 at 25 rpm using the medium phosphate-buffered saline pH 7.4 were considered discriminative and adequate to characterize the rivastigmine (RV) release from a commercial transdermal patch, Exelon® Patch.

Dry powder aerosols to co-deliver antibiotics and nutrient dispersion compounds for enhanced bacterial biofilm eradication

The purpose of this study was to formulate a dry powder for inhalation containing a combination treatment for eradication of Pseudomonas aeruginosa bacterial biofilms. Dry powders containing an antibiotic (ciprofloxacin hydrochloride, CH) and nutrient dispersion compound (glutamic acid, GA) at a ratio determined to eliminate the biofilms were generated by spray drying. Leucine was added to the spray dried formulation to aid powder flowability. A central composite design of experiments was performed to determine the effects of solution and processing parameters on powder yield and aerodynamic properties. Combinations of CH and GA eradicated bacterial biofilms at lower antibiotic concentrations compared to CH alone. Spray dried powders were produced with yields up to 43% and mass mean aerodynamic diameters (MMAD) in the respirable range. Powder yield was primarily affected by variables that determine cyclone efficiency, i.e. atomizer and solution flow rates and solution concentration; while MMAD was mainly determined by solution concentration. Fine particle fractions (FPF)<4.46μm and <2.82μm of the powders ranged from 56 to 70% and 35 to 46%, respectively. This study demonstrates that dry powder aerosols containing high concentrations of a combination treatment effective against P. aeruginosa biofilms could be developed with high yield, aerodynamic properties appropriate for inhalation, and no loss of potency.