Polycyclic aromatic hydrocarbons degradation and microbial community shifts during co-composting of creosote-treated wood

Effects of different organic substrate compositions on the decontamination of aged PAH-polluted soils through outdoor co-composting

The effects of different organic substrate compositions on the efficiency of outdoor co-composting as a bioremediation technology for decontaminating soil polluted by polycyclic aromatic hydrocarbons (PAHs) were investigated. Four different substrate mixtures and two different aged PAH-contaminated soils were used in a semi-pilot-scale experiment that lasted nearly 700 days. The two soils (A and B) differed concerning both the initial concentrations of the Ʃ16 US EPA PAHs (5926 vs. 369 mg kg-1, respectively) and the type of predominant PAH group by molecular weight. The experiments revealed that while the composition of the organic substrate had an impact on the rate of PAH degradation, it did not significantly influence the final extent of PAH degradation. Notably, the organic substrate consisting of green waste and wood chips (GW) was found to facilitate the most rapid rate of PAH degradation (first-order rate constant k = 0.033 ± 0.000 d-1 with soil A over the initial 42 days of the experiment and k = 0.036 ± 0.000 d-1 with soil B over the initial 56 days). Despite the differences in organic substrate compositions and types of soil being treated, PAH degradation levels exceeded at least 95% in all the treatments after more than 680 days of co-composting. Regardless of the composition, the removal of low- and medium- molecular-weight (2-4 rings) PAHs was nearly complete by the end of the experiment. Furthermore, high-molecular-weight PAHs (5 rings and more) were significantly degraded during co-composting, with reductions ranging from 54% to 79% in soil A and from 59% to 68% in soil B. All composts were dominated by Proteobacteria, Firmicutes, and Actinobacteria, with significant differences in abundance between soils. Genera with PAH degradation potentials were detected in all samples. The results of a battery of toxicity tests showed that there was almost no toxicity associated with the final composts.

Nano zerovalent Fe did not reduce metal(loid) leaching and ecotoxicity further than conventional Fe grit in contrasting smelter impacted soils: A 1-year field study

The majority of the studies on nanoscale zero-valent iron (nZVI) are conducted at a laboratory-scale, while field-scale evidence is scarce. The objective of this study was to compare the metal(loid) immobilization efficiency of selected Fe-based materials under field conditions for a period of one year. Two contrasting metal(loid) (As, Cd, Pb, Zn) enriched soils from a smelter-contaminated area were amended with sulfidized nZVI (S-nZVI) solely or combined with thermally stabilized sewage sludge and compared to amendment with microscale iron grit. In the soil with higher pH (7.5) and organic matter content (TOC = 12.7 %), the application of amendments resulted in a moderate increase in pH and reduced As, Cd, Pb, and Zn leaching after 1-year, with S-nZVI and sludge combined being the most efficient, followed by iron grit and S-nZVI alone. However, the amendments had adverse impacts on microbial biomass quantity, S-nZVI being the least damaging. In the soil with a lower pH (6.0) and organic matter content (TOC = 2.3 %), the results were mixed; 0.01 M CaCl2 extraction data showed only S-nZVI with sludge as remaining effective in reducing extractable concentrations of metals; on the other hand, Cd and Zn concentrations were increased in the extracted soil pore water solutions, in contrast to the two conventional amendments. Despite that, S-nZVI with sludge enhanced the quantity of microbial biomass in this soil. Additional earthworm avoidance data indicated that they generally avoided soil treated with all Fe-based materials, but the presence of sludge impacted their preferences somewhat. In summary, no significant differences between S-nZVI and iron grit were observed for metal(loid) immobilization, though sludge significantly improved the performance of S-nZVI in terms of soil health indicators. Therefore, this study indicates that S-nZVI amendment of soils alone should be avoided, though further field evidence from a broader range of soils is now required.

New insights into vermiremediation of sewage sludge: The effect of earthworms on micropollutants and vice versa

Vermicomposting represents an environmentally friendly method for the treatment of various types of biowastes, including sewage sludge (SS), as documented in numerous studies. However, there are few papers providing insights into the mechanisms and toxicity effects involved in SS vermicomposting to present a comprehensive overview of the process. In this work, the vermiremediation of SS containing various micropollutants, including pharmaceuticals, personal care products, endocrine disruptors, and per/polyfluoroalkyl substances, was studied. Two SSs originating from different wastewater treatment plants (WWTP1 and WWTP2) were mixed with a bulking agent, moistened straw, at ratios of 0, 25, 50, and 75% SS. Eisenia andrei earthworms were introduced into the mixtures, and after six weeks, the resulting materials were subjected to various types of chemical and toxicological analyses, including conventional assays (mortality, weight) as well as tissue- and cell-level assays, such as malondialdehyde production, cytotoxicity tests and gene expression assays. Through the vermiremediation process significant removal of diclofenac (90%), metoprolol (88%), telmisartan (62%), and triclosan (81%) was achieved. Although the concentrations of micropollutants were substantially different in the original SS samples, the micropollutants vermiaccumulated to a similar extent over the incubation period. The earthworms substantially eliminated the present bacterial populations, especially in the 75% SS treatments, in which the average declines were 90 and 79% for WWTP1 and WWTP2, respectively. To the best of our knowledge, this is the first study to investigate the vermiremediation of such a large group of micropollutants in real SS samples and provide a thorough evaluation of the effect of SS on earthworms at tissue and cellular level.

Composting post-anaerobic digestion for emerging contaminant biodegradation: Impacts of operating conditions

Sustainable manure management technologies are needed, and combining anaerobic digestion (AD) for energy generation and aerobic composting (AC) to stabilize digestate and remove emerging contaminants (ECs), including veterinary pharmaceuticals and steroid hormones, is promising. This study identified post-AD, AC operating conditions that maximized degradation of study ECs, expected to be present in cattle manure digested using treated municipal wastewater as the water source. Study ECs included sulfamethoxazole (SMX), chlortetracycline (CTC), oxytetracycline (OTC), estrone (E1), and naproxen (NPX). Composting conditions were simulated in bench-scale reactors, with microorganisms from digestate produced in an AD system (25L scale), by varying temperatures, pH, and carbon source compositions (representing food waste/manure co-digestion with different residence times). Results indicate maximum SMX biodegradation occurred at 35°C, pH 7, and with high levels of easily degradable carbon (≥99%, 99%, and 98%), and maximum E1 biodegradation occurred at 35°C, and with low levels of easily degradable carbon (≥97% and 99%). Abiotic degradation was responsible for the nearly complete removal of tetracyclines under all conditions and for partial degradation of NPX (between 20% and 48%). Microorganisms originating from the AD system putatively capable of SMX and E1 biodegradation, or of contributing to biodegradation during the AC phase, were identified, including phylotypes previously shown to biodegrade SMX (Brevundimonas and Alcaligenes).

Polycyclic aromatic hydrocarbon (PAH) remediation during vermicomposting and composting: Mechanistic insights through PAH-budgeting

Knowledge on the mechanism of earthworm-induced removal of polycyclic aromatic hydrocarbons (PAH) in vermicomposting systems and interaction with nutrient mineralization and microbial growth is scarce in literature. Moreover, the PAH accumulation capacity of Eudrilus eugeniae has not been studied. This research, therefore, investigates the apportionment dynamics of 13 PAH compounds in aerobic composting and vermicomposting (Eisenia fetida and E. eugeniae) systems using novel budget equations. The PAH removal efficiency of vermicomposting was significantly higher (2-threefold) than composting with concurrent microbial augmentation (p < 0.01). However, the 4-6 ring compounds reduced more significantly (30-50%) than the 3-ring PAHs (p < 0.01), and E. eugeniae was an equally competitive PAH-accumulator compared to E. fetida. The budget equations revealed that although the bioaccumulation capabilities of earthworms were retarded due to PAH exposure, earthworms facilitated PAH-immobilization in decomposed feedstock. A marked increase in bacterial, fungal, and actinomycetes proliferation in PAH-spiked vermibeds with parallel removal of the PAHs indicated that earthworm-induced microbial enrichment plays a vital role in PAH detoxification during vermicomposting. Correlation analyses strongly implied that earthworm-driven mineralization-humification balancing and microbial enrichment could be the critical mechanism of PAH remediation under vermicomposting.

Ex situ bioremediation of diesel fuel-contaminated soil in two different climates

The petroleum industry is often faced with accidental spills and discharges that pollute valuable natural resources such as soil. The purpose of this study was to assess bioremediation potential of an on-site landfarming unit (LU), a highly economical solution that complies with the zero-waste policy, for bioremediation of the contaminated soil after an actual diesel fuel leakage in a fuel depot. The first aim was to evaluate the effects of different climates on hydrocarbon bioremediation. For this reason, a part of the contaminated soil was moved from the initial location with a sub-Mediterranean climate to an LU at another location with a temperate continental climate. Our results demonstrated that remediation in sub-Mediterranean climate is less effective than the remediation in a temperate continental climate. The second aim of this study was to evaluate the effect of different plant species on the microbial population during bioremediation. For that purpose, 365-day monitoring of phospholipid fatty acids (PLFA) was performed. Our results support the hypothesis that plant-assisted bioremediation can diminish toxic effects of diesel-polluted soil and that the changes in plant species during bioremediation cause changes in the microbial population.

Bisphenol S degradation in soil and the dynamics of microbial community associated with degradation

Bisphenol S (BPS) has been widely applied as a replacement for BPA in industrial application, leading to the frequent detection in the environment. However, its impact on soil microbial communities has not been well reported. Here, effects of BPS exposure on soil microbial communities in the presence of polystyrene (PS) microplastics were revealed. Rapid degradation of BPS occurred with a degradation rate of up to 98.9 ± 0.001 % at 32 d. The presence of BPS reduced the diversity of soil microbial communities, and changed community structures. After BPS treatment, Proteobacteria, and its members Methylobacillus, Rhodobacteraceae and Mesorhizobium became dominant, and were considered as potential biomarkers indicating BPS contamination. Co-occurrence network analysis revealed the increased relationships of certain groups of microbes after BPS treatment. The resultant low stability and resilience towards environment disturbance of microbial community networks implied the biotoxicity of BPS towards soil ecosystems. The degradation and biotoxicity of BPS (p > 0.05) in soil was not affected by the presence of PS. Our findings showed that exposure to BPS could reshape soil microbial communities and impair the robustness of microbial co-occurrence networks.

Effects of combined pollution of organic pollutants and heavy metals on biodiversity and soil multifunctionality in e-waste contaminated soil

Electronic waste (e-waste) is increasing globally, but the impact of this source of combined pollution on soil biodiversity and multiple soil functions (i.e., ecosystem multifunctionality) remains unclear. Here, we evaluated the effects of combined pollution on the biodiversity and soil multifunctionality using samples collected from upland and paddy soils chronically contaminated with e-waste. Overall biodiversity, as well as the relative abundance and biodiversity of key ecological clusters, as combined pollution concentrations increased in upland soil, while the opposite was true in paddy soil. Soil multifunctionality followed the same trend. Organic pollutants had significant negative effects on soil multifunctionality and were the main influencing factors in upland soil. Heavy metals had significant positive effects on soil multifunctionality in paddy soil. Moreover, driving soil multifunctionality was overall biodiversity in upland soil but key biodiversity in paddy soil. Importantly, a strong positive association between key organism biodiversity and soil multifunctionality was found in soil with low contamination. However, the relationship between key organism biodiversity and soil multifunctionality weakened or disappeared in highly contaminated soil, whereas overall biodiversity was significantly and positively correlated with multifunctionality. Our results emphasized that severe e-waste contamination would reduce soil biodiversity and soil multifunctionality and warrants high attention.

Application of dry olive residue-based biochar in combination with arbuscular mycorrhizal fungi enhances the microbial status of metal contaminated soils

Biochar made-up of dry olive residue (DOR), a biomass resulting from the olive oil extraction industry, has been proposed to be used as a reclamation agent for the recovery of metal contaminated soils. The aim of the present study was to investigate whether the soil application of DOR-based biochar alone or in combination with arbuscular mycorrhizal fungi (AMF) leads to an enhancement in the functionality and abundance of microbial communities inhabiting metal contaminated soils. To study that, a greenhouse microcosm experiment was carried out, where the effect of the factors (i) soil application of DOR-based biochar, (ii) biochar pyrolysis temperature (considering the variants 350 and 500 °C), (iii) soil application dose of biochar (2 and 5%), (iv) soil contamination level (slightly, moderately and highly polluted), (v) soil treatment time (30, 60 and 90 days) and (vi) soil inoculation with Funneliformis mosseae (AM fungus) on β-glucosidase and dehydrogenase activities, FA (fatty acid)-based abundance of soil microbial communities, soil glomalin content and AMF root colonization rates of the wheat plants growing in each microcosm were evaluated. Biochar soil amendment did not stimulate enzyme activities but increased microbial abundances. Dehydrogenase activity and microbial abundances were found to be higher in less contaminated soils and at shorter treatment times. Biochar pyrolysis temperature and application dose differently affected enzyme activities, but while the first factor did not have a significant effect on glucosidase and dehydrogenase, a higher biochar dose resulted in boosted microbial abundances. Soil inoculation with F. mosseae favored the proliferation of soil AMF community and increased soil glomalin content as well as rates of AMF root colonization. This factor also interacted with many of the others evaluated to significantly affect soil enzyme activities, microbial abundances and AMF community. Our results indicate that the application of DOR-based biochar along with AMF fungi is an appropriate approach to improve the status of microbial communities in soils with a moderate metal contamination at short-term.

Microbial diversity drives pyrene dissipation in soil

Soil microbial diversity is an essential driver of multiple ecosystem functions and services. However, the role and mechanisms of microbial diversity in the dissipation of persistent organic pollutants in soil are largely unexplored. Here, a gradient of soil microbial diversity was constructed artificially by a dilution-to-extinction approach to assess the role of soil microbial diversity in the dissipation of pyrene, a high molecular weight polycyclic aromatic hydrocarbon (PAH), in a 42-day microcosm experiment. The results showed that pyrene dissipation (98.1%) and the abundances of pyrene degradation genes (the pyrene dioxygenase gene nidA and the gram-positive PAH-ring hydroxylating dioxygenase gene PAH-RHDα GP) were highest in soils with high microbial diversity. Random-forest machine learning was combined with linear regression analysis to identify a range of keystone taxa (order level) associated with pyrene dissipation, including Sphingobacteriales, Vampirovibrionales, Blastocatellales, Myxococcales, Micrococcales and Rhodobacterales. The diversity of these keystone taxa was significantly and positively correlated with the abundance of pyrene degradation genes and the removal rate of pyrene. According to (partial) Mantel tests, keystone taxa diversity was the dominant factor determining pyrene dissipation compared with total microbial diversity. Moreover, co-occurrence network analysis revealed that diverse keystone taxa may drive pyrene dissipation via more positive interactions between keystone species and with other species in soil. Taken together, these findings provide new insights on the regulation of keystone taxa diversity to promote the dissipation of PAH in soil.

Processing Agroindustry By-Products for Obtaining Value-Added Products and Reducing Environmental Impact

Over four billion tons of foods are produced annually on the planet, and about a third is wasted. A minimal part of this waste is incinerated or sent to landfills for treatment, avoiding contamination and diseases; the rest is disposed of elsewhere. The current review was aimed at broadening the panorama on the potential of agroindustrial by-products in applications such as biofuels, biomaterials, biocompounds, pharmaceuticals, and food ingredients. It also exposes the main chemical, physical, and biochemical treatments for converting by-products into raw materials with added value through low environmental impact processes. The value of agroindustrial waste is limited due to the scarce information available. There is a need for further research in unexplored areas to find ways of adding value to these by-products and minimizing their contamination. Instead of throwing away or burning by-products, they can be transformed into useful materials such as polymers, fuels, antioxidants, phenols, and lipids, which will effectively reduce food waste and environmental impact.

Composting and its application in bioremediation of organic contaminants

This review investigates the findings of the most up-to-date literature on bioremediation via composting technology. Studies on bioremediation via composting began during the 1990s and have exponentially increased over the years. A total of 655 articles have been published since then, with 40% published in the last six years. The robustness, low cost, and easy operation of composting technology make it an attractive bioremediation strategy for organic contaminants prevalent in soils and sediment. Successful pilot-and large-scale bioremediation of organic contaminants, e.g., total petroleum hydrocarbons, plasticizers, and persistent organic pollutants (POPs) by composting, has been documented in the literature. For example, composting could remediate >90% diesel with concentrations as high as 26,315 mg kg^−a of initial composting material after 24 days. Composting has unique advantages over traditional single- and multi-strain bioaugmentation approaches, including a diverse microbial community, ease of operation, and the ability to handle higher concentrations. Bioremediation via composting depends on the diverse microbial community; thus, key parameters, including nutrients (C/N ratio = 25–30), moisture (55–65%), and oxygen content (O₂ > 10%) should be optimized for successful bioremediation. This review will provide bioremediation and composting researchers with the most recent finding in the field and stimulate new research ideas.

Construction of a novel microbial consortium valued for the effective degradation and detoxification of creosote-treated sawdust along with enhanced methane production

Lignocellulosic biomass represents an unlimited and ubiquitous energy source, which can effectively address current global challenges, including climate change, greenhouse gas emissions, and increased energy demand. However, lignocellulose recalcitrance hinders microbial degradation, especially in case of contaminated materials such as creosote (CRO)-treated wood, which necessitates appropriate processing in order to eliminate pollution. This study might be the first to explore a novel bacterial consortium SST-4, for decomposing birchwood sawdust, capable of concurrently degrading lignocellulose and CRO compounds. Afterwards, SST-4 which stands for molecularly identified bacterial strains Acinetobacter calcoaceticus BSW-11, Shewanella putrefaciens BSW-18, Bacillus cereus BSW-23, and Novosphingobium taihuense BSW-25 was evaluated in terms of biological sawdust pre-treatment, resulting in effective lignocellulose degradation and 100% removal of phenol and naphthalene. Subsequently, the maximum biogas production observed was 18.7 L/kg VS, while cumulative methane production was 162.8 L/kg VS, compared to 88.5 without microbial pre-treatment. The cumulative energy production from AD-I and AD-II through biomethanation was calculated as 3177.1 and 5843.6 KJ/kg, respectively. The pretreatment process exhibited a significant increase in the energy yield by 83.9%. Lastly, effective CRO detoxification was achieved with EC₅₀ values exceeding 90%, showing the potential for an integrated process of effective contaminated wood management and bioenergy production.

Difference and interplay of microbial communities, metabolic functions, trophic modes and influence factors between sludge and bulking agent in a composting matrix

The difference and interplay of microbial communities, metabolic functions and influence factors between sewage sludge and bulking agent were evaluated in 60 days composting. Results showed that fungal communities were mainly affected by pH (42.4%) and ORP (35.9%) of sludge but by VS (41.1%) and temperature (34.7%) of sawdust in a composting system. Bacterial communities were primarily affected by VS (43.5%) and C/N (34.8%) of sludge but by ORP (44.5%) and temperature (31.0%) of sawdust. Tepidimicrobium dominated in the sludge at thermophilic period, while Alcaligenes prevailed in the sawdust. Bacterial carbon metabolism was significantly higher in the sludge than that in the sawdust except carbohydrate metabolism. Saprophytic fungi were the main trophic mode both in the sludge and sawdust. Water transfer facilitated Aspergillus and Trichosporon moving from sludge to sawdust to decompose lignocellulose. Ammonia transfer promoted the migration of Alcaligenes and Pseudomonas from sludge to sawdust and facilitated ammonia assimilating.

Statistical Evaluation of Quantities Measured in the Detection of Soil Air Pollution of the Environmental Burden

The article highlights the investigation of the relationships between measured quantities during the atmospheric geochemical survey of contaminated soil and the environmental burden of the industrial establishment in eastern Slovakia. Statistical data processing was undertaken from the measured values of pollutants. The basic statistical characteristics of the monitored indicators were defined here. With the help of regressive and correlative analysis, dependency was confirmed between examined values, further expressed by a mathematical relationship. We analysed variability of the measured variables due to the influence of changed input quantities by the non-parametric Wilcox test. The statistical data processing helps us to identify the dependency between the measured values and improves valorization of the pollution of a given environmental burden. This was due to the handling of organic pollutants and the production of basic organic and inorganic chemicals stated for other industries. Chemical analysis of soil air helps us to determine the extent and amount of soil contamination by pollutants. Individual pollutants have their own characteristic properties and their negative effects on biota, the environment and humans are different.

Effects of organic matter addition on chronically hydrocarbon-contaminated soil

Soil is the recipient of organic pollutants as a consequence of anthropogenic activities. Hydrocarbons are contaminants that pose a risk to human and environmental health. Bioremediation of aging contaminated soils is a challenge due to the low biodegradability of contaminants as a result of their interaction with the soil matrix. The aim of this work was to evaluate the effect of both composting and the addition of mature compost on a soil chronically contaminated with hydrocarbons, focusing mainly on the recovery of soil functions and transformations of the soil matrix as well as microbial community shifts. The initial pollution level was 214 ppm of polycyclic aromatic hydrocarbons (PAHs) and 2500 ppm of aliphatic hydrocarbons (AHs). Composting and compost addition produced changes on soil matrix that promoted the release of PAHs (5.7 and 15 % respectively) but not the net PAH elimination. Interestingly, composting stimulated AHs elimination (about 24 %). The lack of PAHs elimination could be attributed to the insufficient PAHs content to stimulate the microbial degrading capacity, and the preferential consumption of easily absorbed C sources by the bacterial community. Despite the low PAH catabolic potential of the aging soil, metabolic shift was driven by the addition of organic matter, which could be monitored by the ratio of Proteobacteria to Actinobacteria combined with E₄/E₆ ratio. Regarding the quality of the soil, the nutrients provided by the exogenous organic matter contributed to the recovery of the global functions and species diversity of the soil along with the reduction of phytotoxicity.

Diversity and structure of phenanthrene degrading bacterial communities associated with fungal bioremediation in petroleum contaminated soil

Fungal bioremediation is a promising technique for the cleanup of sites contaminated with polycyclic aromatic hydrocarbons (PAHs). However, due to limited understanding of the composition and dynamics of the native PAH-degrading microorganisms in contaminated sites, its application has been difficult. In the present study, DNA stable-isotope probing was performed to identify indigenous phenanthrene (PHE)-degrading bacteria and determine their diversity during the fungal bioremediation process. The results showed a total of 14 operational taxonomic units (OTUs) enriched in the heavy DNA fractions, which were related to seven genera (Sphingomonas, Sphingobacterium, Acidovorax, Massilia, Flavobacterium, Cupriavidus, Aeromicrobium, and unclassified Chitinophagaceae). Along with enhanced efficiency of PHE removal, the number and diversity of indigenous PHE-degrading bacteria in soil bioaugmented with fungi were significantly increased. Furthermore, based on the results of linear model analysis, we found that PHE degraders affiliated with the genus Sphingomonas were significantly enriched during fungal bioremediation. Moreover, fungal bioaugmentation promoted indigenous functional Proteobacteria involved in PAH degradation through co-metabolism, suggesting that PAH biodegradation was attributable to cooperative metabolism by fungi and indigenous bacteria. Our findings provide new insights into the diversity of PHE-degrading communities and support a more comprehensive view of the fungal bioremediation process.

Effect of pyrolysis temperature on removal of organic pollutants present in anaerobically stabilized sewage sludge

Sewage sludge was excluded from the list of component materials for the production of EU fertilizing products and it was banned as feedstock to produce pyrolysis & gasification materials in European Commission's technical proposals for selected new fertilizing materials under the Regulation 2019/1009 (STRUBIAS report). This exclusion of pyrolysis as a viable way to treat sewage sludge was mainly due to the lack of data on the fate of organic pollutants at pyrolysis conditions. In this work, we are addressing this knowledge gap. We studied slow pyrolysis as a potential process to efficiently treat organic pollutants present in stabilized sewage sludge. Sewage sludge was pyrolyzed in a quartz fixed bed reactor at temperatures of 400-800 °C for 2 h and the sludge and resulting sludge-chars were analyzed for the presence of four groups of organic pollutants, namely (i) polychlorinated biphenyls (PCBs), (ii) polycyclic aromatic hydrocarbons (PAHs), (iii) pharmaceuticals, and (iv) endocrine-disrupting and hormonal compounds. Pyrolysis at ≥ 400 °C effectively removed pharmaceuticals (group iii) to below detection limits, whereas pyrolysis at temperatures higher than 600 °C was required to remove more than 99.8% of the compounds from groups i, ii and iv. Based on these findings, we propose, that high temperature (>600 °C) slow pyrolysis can satisfactory remove organic pollutants from the resulting sludge-char, which could be safely applied as soil improver.

Degradation and effect of 6:2 fluorotelomer alcohol in aerobic composting of sludge

Perfluoroalkyl carboxylates (PFCAs) is toxic to the environment and human health. However, the degradation characteristics of fluorotelomer alcohols (FTOHs), precursors of PFACAs biodegradation, in the sludge during aerobic composting remain unclear. In this study, the degradation characteristics of 6:2 FTOH in sewage sludge by composting were researched and the influences of 6:2 FTOH on the composting process and microbial communities of the sludge were evaluated. After 52 days of composting, 6:2 FTOH retained only 0.73% of its original concentration, and its half-life was less than 1 d; 6:2 FTOH was degraded finally to perfluorohex unsaturated acid, perfluoropentanoic acid, 5:3 polyfluorinated acid (FTCA), 4:3 FTCA, and perfluorobutanoic acid through two pathways; and 6:2 FTCA and 6:2 fluorotel unsaturated acid were the intermediate products. Notably, dosing with 6:2 FTOH affected the composting process of sewage sludge. Additionally, 50 mg/kg 6:2 FTOH resulted in a decrease in the microbial richness and diversity of sludge compost. When compared with the compost without 6:2 FTOH, the proportion of Proteobacteria had increased, and the proportion of Firmicutes had decreased as the concentration of 6:2 FTOH increased. The negative effect of a dosage of 50 mg/kg 6:2 FTOH was more obvious than the effect of other treatments. This study expanded our understanding of the risk of sludge contaminated by 6:2 FTOH being used as a fertilizer after composting.

Aerobic composting remediation of petroleum hydrocarbon-contaminated soil. Current and future perspectives

This article provides a comprehensive review on aerobic composting remediation of soil contaminated with total petroleum hydrocarbons (TPHs). The studies reviewed have demonstrated that composting technology can be applied to treat TPH contamination (as high as 380,000 mg kg^-1) in clay, silt, and sandy soils successfully. Most of these studies reported more than 70% removal efficiency, with a maximum of 99%. During the composting process, the bacteria use TPHs as carbon and energy sources, whereas the fungi produce enzymes that can catalyze oxidation reactions of TPHs. The mutualistic and competitive interactions between the bacteria and fungi are believed to sustain a robust biodegradation system. The highest biodegradation rate is observed during the thermophilic phase. However, the presence of a diverse and dynamic microbial community ensures that TPH degradation occurs in the entire composting process. Initial concentration, soil type, soil/compost ratio, aeration rate, moisture content, C/N ratio, pH, and temperature affect the composting process and should be monitored and controlled to ensure successful degradation. Nevertheless, there is insufficient research on optimizing these operational parameters, especially for large-scale composting. Also, toxic and odorous gas emissions during degradation of TPHs, usually unaddressed, can be potential air pollution sources and need further insightful characterization and mitigation/control research.

Primary Sources of Polycyclic Aromatic Hydrocarbons to Streambed Sediment in Great Lakes Tributaries Using Multiple Lines of Evidence

Polycyclic aromatic hydrocarbons (PAHs) are among the most widespread and potentially toxic contaminants in Great Lakes (USA/Canada) tributaries. The sources of PAHs are numerous and diverse, and identifying the primary source(s) can be difficult. The present study used multiple lines of evidence to determine the likely sources of PAHs to surficial streambed sediments at 71 locations across 26 Great Lakes Basin watersheds. Profile correlations, principal component analysis, positive matrix factorization source-receptor modeling, and mass fractions analysis were used to identify potential PAH sources, and land-use analysis was used to relate streambed sediment PAH concentrations to different land uses. Based on the common conclusion of these analyses, coal-tar-sealed pavement was the most likely source of PAHs to the majority of the locations sampled. The potential PAH-related toxicity of streambed sediments to aquatic organisms was assessed by comparison of concentrations with sediment quality guidelines. The sum concentration of 16 US Environmental Protection Agency priority pollutant PAHs was 7.4-196 000 µg/kg, and the median was 2600 µg/kg. The threshold effect concentration was exceeded at 62% of sampling locations, and the probable effect concentration or the equilibrium partitioning sediment benchmark was exceeded at 41% of sampling locations. These results have important implications for watershed managers tasked with protecting and remediating aquatic habitats in the Great Lakes Basin. Environ Toxicol Chem 2020;39:1392-1408. © 2020 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Adding value to home compost: Biopesticide properties through Bacillus thuringiensis inoculation

Home and community composting are considered potential tools for the self-management of organic waste. The production of added value products from biowaste is an encouraging step further to valorise this waste stream. To increase the profits of homemade compost, this paper presents a strategy to produce enriched home compost with biopesticide properties through a simple and low-cost process. Bacillus thuringiensis (Bt) was inoculated in a home composter bin through a solid inoculum previously prepared using the same waste as substrate. The process was monitored and compared with a home composting control process without inoculation. Final composts were analysed and compared in terms of physicochemical and microbiological properties, respiration and germination indices, indicating the suitability of both to be used as organic amendments. Also, a standardized toxicity test proved that Bt-enriched compost can be safely applied to the soil. Microbiological analysis revealed highly diverse communities in both cases, with limited differences at phylum taxonomic level, but dissimilar relative abundances of species within phylum. Bacteroidetes and Proteobacteria were dominant, with the presence of species able to transform organic matter from vegetal origin, but not usually related to compost. Bt-cristal toxin was clearly present in Bt-enriched compost, indicating the coexistence of Bt with the different microbial populations till the end of the composting process. Although Bt has been widely investigated due to its biopesticide properties, the incorporation of this microorganism to home composting level has not been previously reported.

Dissipation of polycyclic aromatic hydrocarbons (PAHs) in soil amended with sewage sludge and sludge compost

In this study, greenhouse experiments were conducted under the condition of different amendment ratios and planting tall fescue (Festuca arundinacea). The amendment ratios of sewage sludge or sludge compost to soil were of 0, 10, 25, and 50% (w/w). The removal rates of PAH, catalase, and dehydrogenase activities of amended soil and accumulation of PAHs by vegetation were detected to investigate the differences of PAH dissipation in sludge-amended and compost-amended soils. The initial PAH concentrations in three amended soils increased with the more addition of sludge or compost. After 126-day experiment, maximum PAH removal rates were observed in sludge-amended and compost-amended soils with PAH concentration of about 200 μg kg^-1. And the removal of PAHs showed better efficiencies in compost soil rather than in sludge soil. The more catalase activity and dehydrogenase activity of soil were obtained, respectively, in sludge soil and compost soil. The results indicated that the mechanism of PAH dissipation in two types of amended soils were different. The abundant amount of microorganism dominated PAH dissipation in sludge soils, and PAHs dissipated mainly caused of intense activity of microorganism in compost soils. In addition, PAH accumulation in tall fescue suggested that the transference approach of PAHs was from soil to the roots, and then accumulated in the shoots of tall fescue. It was prone to store up more PAHs in vegetation in the condition of high molar weight of PAHs, more biomass of vegetation, and heavy PAH concentration in soil.

Implications of mycoremediated dry olive residue application and arbuscular mycorrhizal fungi inoculation on the microbial community composition and functionality in a metal-polluted soil

Metal-polluted soils represent hostile environments affecting the composition and functions of soil microbial communities. This study evaluated the implication of combining the mycoremediated dry olive residue (MDOR) amendment application with the inoculation of the arbuscular mycorrhizal fungi (AMF) Funneliformis mosseae in restoring the quality, composition, and functionality of soil microbial communities. To achieve this aim, a mesocosms experiment was set up that included three variations: i) with and without application of Penicillium chrysogenum-10-transformed MDOR (MDOR_Pc), and Chondrosterum purpureum-transformed MDOR (MDOR_Cp) amendments; ii) with and without F. mosseae inoculation; and iii) 30-day and 60-day soil treatment time. As a result of this combined treatment, changes in the soil labile organic C and N fractions were observed throughout the experiment. Increases in the abundance of phospholipid fatty acids (PLFAs) for bacteria, actinobacteria, and Gram- and Gram+ bacteria were also recorded at the end of the experiment. The addition of MDOR amendments boosted fungal and AM fungi communities. AM fungi root and soil colonization was also enhanced as the result of improvement nutrient turnover and spatial conditions caused by adding MDOR in combination with an inoculation of F. mosseae. The composition and functionality of microbial communities seemed to be an important ecological attribute indicating an apparently fully functional restoration of this metal-polluted soil and therefore suggesting the suitability of the combined MDOR and AM fungus treatment as a reclamation practice.

A novel comparative study of modified carriers in moving bed biofilm reactor for the treatment of wastewater: Process optimization and kinetic study

In this work, modified plastic carriers; polypropylene (PP), low-density polyethylene- polypropylene (LDPE-PP), and polyurethane foam-polypropylene (PUF-PP) were developed and used in moving bed bioreactor (MBBR) for the wastewater treatment containing naphthalene. To optimized the process parameters using response surface methodology (RSM), two numerical variables; pH (5.0-9.0) and hydraulic retention time (HRT) (1.0-5.0 day) along with the type of carriers (PP, LDPE-PP, and PUF-PP) were selected as a categorical factor. At 7.0 pH and 5 days HRT, maximum removal efficiencies were observed to be 72.4, 84.4, and 90.2% for MBBR packed with PP, LDPE-PP, and PUF-PP carriers, respectively. Gas chromatography-mass spectrometry (GC-MS) analysis reveals catechol and 2-naphthol were observed as intermediate metabolites for naphthalene degradation. Modified Stover-Kincannon model was applied for biodegradation kinetic and constants were observed as U_max: 0.476, 0.666, and 0.769 g/L.day and K_B: 0.565, 0.755, and 0.874 g/L.day for PP, LDPE-PP, PUF-PP, respectively.

Thermophilic composting of hydrocarbon residue with sewage sludge and fish sludge as cosubstrates: Microbial changes and TPH reduction

The hydrocarbon residue in petroleum product storage tanks is waste generated in large quantities that must be properly managed to reduce its risk to the environment. By comparing the effect of two organic cosubstrates, the aim of our research is to determine the feasibility of composting as a bioremediation method for the treatment of the solid phase of the hydrocarbon residue. For this purpose, four treatments of the pollutant waste were established in triplicate: waste only; waste with bulking agent (1:2); waste with fish sludge and bulking agent (1:2:6); and waste with municipal sewage sludge and bulking agent (1:2:6). The composting system consisted of 12 reactors with a capacity of 30 L, each equipped with aeration and temperature control. Both at the beginning and the end of the experiment (20 days), we evaluated the physicochemical parameters, the structure of the microbial community through phospholipid fatty acid analysis, and the total petroleum hydrocarbon content (TPH). Treatments with cosubstrates maintained thermophilic temperatures, during 14 and 8 days in fish and municipal sludge respectively, while in the controls mesophilic conditions were maintained. The incorporation of fish sludge decreased TPH present in the initial mixture by 39.5%. The municipal sludge treatment resulted in a lower of temperatures and a TPH decrease close to 23.9%. In the control treatments, there was a slight TPH decrease, mainly due to the forced ventilation. Although, both composting treatments with cosubstrates proved adequate for the bioremediation of residue from hydrocarbon storage tanks, fish sludge presented best bioremediation conditions. Municipal sewage sludge provided a bioaugmentation effect due to its rich diversity and microbial biomass. Fish sludge could have biostimulant and surfactant effect producing an aliphatic mixture of pollutant waste with the nutritional requirements to promote the development of fungal communities.

Effects of benzo [a] pyrene (BaP) on the composting and microbial community of sewage sludge

Benzo [a] pyrene (BaP), the most ubiquitous polycyclic aromatic hydrocarbons (PAHs) found in sludge, can impact the composting processes of sewage sludge as well as the quality of compost produced. In the present study, we investigated the effects of BaP at various concentrations on physicochemical characteristics, heavy metal passivation, and microbial community during the composting processes. The removal efficiency of BaP at 5 and 20 mg kg^-1 after composting was 51.1% and 74.2%, respectively. In comparison with the control, the content of residual Cu, Pb, Cr and Ni in 5 mg kg^-1 BaP contained system declined dramatically on the second day of composting, while such content in 20 mg kg^-1 BaP system significantly decreased on the 8th day. Regardless of the presence of BaP in the sludge, composting process had a positive passivation effect on Cu, Pb, Cr and Ni. A stronger inhibitory effect of BaP at higher concentration was observed on microorganism, which reduced microbial abundance and species in the composting, and influenced microbial diversity. Besides, microbial communities in BaP-containing composting would improve the transformation of silicates and minerals, increase the concentration of humus and extend the passivation time of heavy metals. As these results verified, composting process could remove BaP from the sludge effectively, and BaP had a significant impact on heavy metal passivation and abundance and composition of microbial community during the composting process.

Aerobic co-composting degradation of highly PCDD/F-contaminated field soil. A study of bacterial community

This study investigated bacterial communities during aerobic food waste co-composting degradation of highly PCDD/F-contaminated field soil. The total initial toxic equivalent quantity (TEQ) of the soil was 16,004 ng-TEQ kg^-1 dry weight. After 42-day composting and bioactivity-enhanced monitored natural attenuation (MNA), the final compost product's TEQ reduced to 1916 ng-TEQ kg^-1 dry weight (approximately 75% degradation) with a degradation rate of 136.33 ng-TEQ kg^-1 day^-1. Variations in bacterial communities and PCDD/F degraders were identified by next-generation sequencing (NGS). Thermophilic conditions of the co-composting process resulted in fewer observed bacteria and PCDD/F concentrations. Numerous organic compound degraders were identified by NGS, supporting the conclusion that PCDD/Fs were degraded during food waste co-composting. Bacterial communities of the composting process were defined by four phyla (Proteobacteria, Actinobacteria, Bacteroidetes and Firmicutes). At the genus level, Bacillus (Firmicutes) emerged as the most dominant phylotype. Further studies on specific roles of these bacterial strains are needed, especially for the thermophiles which contributed to the high degradation rate of the co-co-composting treatment's first 14 days.

Performance and microbial protein expression during anaerobic treatment of alkali-decrement wastewater using a strengthened circulation anaerobic reactor

Herein, a strengthened circulation anaerobic (SCA) reactor was employed for the treatment of actual alkali-decrement wastewater. The degradation mechanism of polyester oligomers and the relationship between the treatment performance and microbial community structure were systematically investigated using various advanced techniques. Results suggest that the accumulation of volatile fatty acids has an inhibitory effect on methanogenic activity. Molecular weight distributions suggest that only incomplete degradation of oligomers was achieved, due to acetogenic inhibition in the lower part of the SCA reactor. Meta-proteomic approach analysis revealed that the methanogens containing heterodisulfide reductase were the primary species involved in methane metabolism. Based on these findings, a possible degradation mechanism for alkali-decrement wastewater in the SCA reactor is proposed. This high-performance anaerobic reactor could be further scaled-up and optimized to serve as a promising and effective unit for the treatment of other refractory industrial wastewaters.

A microbial community snapshot of windrows from a commercial composting facility

The effect of depth on compost microbial communities is unclear but could be relevant to the management of windrows at commercial facilities. DNA extracted from 64 compost samples from seven windrows at a commercial facility were analyzed via deep 16S rRNA gene sequencing. The relative abundance of eight to nine genera was affected by depth during the transition from cooling to maturation phases between 4 and 6 months, whereas very few genera (0-1) showed a depth dependence in young, actively managed windrows or in mature windrows older than 10 months. Seven novel bacterial operational taxonomic units (OTUs) were detected in compost DNA and also in publicly available compost metagenomes. A compost metagenome was used to construct a metagenome-assembled genome for most of the abundant uncharacterized OTU in our samples and suggests its involvement in carbon cycling.

The potential impact on the biodegradation of organic pollutants from composting technology for soil remediation

Large numbers of organic pollutants (OPs), such as polycyclic aromatic hydrocarbons, pesticides and petroleum, are discharged into soil, posing a huge threat to natural environment. Traditional chemical and physical remediation technologies are either incompetent or expensive, and may cause secondary pollution. The technology of soil composting or use of compost as soil amendment can utilize quantities of active microbes to degrade OPs with the help of available nutrients in the compost matrix. It is highly cost-effective for soil remediation. On the one hand, compost incorporated into contaminated soil is capable of increasing the organic matter content, which improves the soil environment and stimulates the metabolically activity of microbial community. On the other hand, the organic matter in composts would increase the adsorption of OPs and affect their bioavailability, leading to decreased fraction available for microorganism-mediated degradation. Some advanced instrumental analytical approaches developed in recent years may be adopted to expound this process. Therefore, the study on bioavailability of OPs in soil is extremely important for the application of composting technology. This work will discuss the changes of physical and chemical properties of contaminated soils and the bioavailability of OPs by the adsorption of composting matrix. The characteristics of OPs, types and compositions of compost amendments, soil/compost ratio and compost distribution influence the bioavailability of OPs. In addition, the impact of composting factors (composting temperature, co-substrates and exogenous microorganisms) on the removal and bioavailability of OPs is also studied.

Relationship between maturity and microbial communities during pig manure composting by phospholipid fatty acid (PLFA) and correlation analysis

The dynamic of microbial community plays vital role during composting. We therefore conducted a combined study on the maturity of compost (by pig manure composting with covering matured compost) and the successions of microbial communities (via phospholipid fatty acid (PLFA)). Our results showed that pH, electrical conductivity (EC), NH₄-N, and germination index (GI) were suitable indicators for compost maturity evalument. In addition, there was a closer correlation between maturity indexes (NH₄-N and GI) and the microbial compositions (as evaluated by microbial PLFA). The regression predicting model for NH₄-N used bacteria PLFA 15:0 and fungi PLFA 18:1ω9t (R² = 0.98, P < 0.01) and for GI used fungi PLFA 18:1ω9t and 18:1ω9, 12 (R² = 0.94, P < 0.01) as the evidences of good predictive ability. It also indicated that PLFA 18:1ω9t has a good relationship with the changes of NH₄-N and GI during the composting. Our results revealed the potential of using microbial PLFA for evaluating the maturity during pig manure composting.

New insights into biodrying mechanism associated with tryptophan and tyrosine degradations during sewage sludge biodrying

Sewage sludge biodrying is a treatment that uses bio-heat generated from organic degradation to remove water from sewage sludge. Dewatering is still limited during biodrying, due to the presence of extracellular polymeric substances (EPS) in sludge. To study the biodrying mechanism associated with EPS compositions tryptophan and tyrosine degradations, this study investigated the microbial function in sludge biodrying material. This study conducted a taxonomic analysis of biodrying material; determined the most abundant genetic functions; analyzed the functional microorganisms involved in the degradations of tryptophan and tyrosine; and summarized the metabolic pathways. The results indicated efficient degradations of tryptophan and tyrosine were observed during the initial thermophilic phase; functional microorganisms were mainly from the phyla Firmicutes, Actinobacteria, and Proteobacteria, enriched with genes involved in amino acid transport and metabolism. These findings highlight the potentially important microorganisms and typical pathways that may help improve dewaterability during biodegradation.

Impacts of vegetation and temperature on the treatment of domestic sewage in constructed wetlands incorporated with Ferric-Carbon micro-electrolysis material

Ferric-Carbon Micro-Electrolysis (Fe/C-M/E) material had been widely used for the pretreatment of wastewater. Therefore, we hypothesized that Fe/C-M/E material could enhance the treatment of domestic sewage when it was integrated into constructed wetlands (CWs). In this study, CWs integrated with Fe/C-M/E material were developed. Druing the experiment of effect of vegetation on the performance of CWs, percentages of NH₄⁺-N, NO₃^--N, total nitrogen (TN), and Chemical Oxygen Demand (COD) removed in polyculture (W1) were up to 91.8%, 97.0%, 92.3%, and 85.4%, respectively, which were much higher than those in Lythrum salicaria monoculture (W2) and Canna indica monoculture (W3). In the experiment of temperature influences on the removal efficiency of CWs, temperature substantially influenced the performance of CWs. For example, NO₃^--N removal percentages of W1, W2, and W3 at high temperature (25.5°C and 19.8°C) were relatively stable and greater than 85.4%. At 8.9°C, however, a sharp decline of NO₃^--N removal percentage was observed in all CWs. Temperature also influenced the Chemical Oxygen Demand (COD) removal and soil microbial activity and biomass. Overall, the polyculture (Lythrum salicaria +Canna indica) showed the best performance during most of the operating time, at an average temperature ≥ 19.8°C, due to the functional complementarity between vegetation. All the CWs consistently achieved high removal efficiency (above 96%) for TP in all experiments, irrespective of vegetation types, phosphorous loadings, and temperatures. In conclusion, polyculture was an attractive solution for the treatment of domestic sewage during most of the operating time (average temperature ≥ 19.8°C). Furthermore, CWs with Fe/C-M/E material were ideally suitable for domestic sewage treatment, especially for TP removal.

Benefits to decomposition rates when using digestate as compost co-feedstock: Part II - Focus on microbial community dynamics

Linkage between composting reactor performance and microbial community dynamics was investigated during co-composting of digestate and fresh feedstock (organic fraction of municipal solid waste) using 25L reactors. Previously, the relationship between composting performance and various physicochemical parameters were reported in Part I of the study (Arab and McCartney, 2017). Three digestate to fresh feedstock ratios (0, 40, and 100%; wet weight basis) were selected for analysis of microbial community dynamics. The 40% ratio was selected because it was found to perform the best (Arab and McCartney, 2017). Illumina sequencing results revealed that the reactor with a greater composting performance (higher organic matter degradation and higher heat generation; 40% ratio) was associated with higher microbial diversity. Two specific bacterial orders that might result in higher performance were Thermoactinomycetaceae and Actinomycetales with a higher sequence abundance during thermophilic composting phase and during the maturing composting phase, respectively. Galactomyces, Pichia, Chaetomium, and Acremonium were the four fungal genera that are probably also involved in higher organic matter degradation in the reactor with better performance. The redundancy analysis (RDA) biplot indicated that among the studied environmental variables, temperature, total ammonia nitrogen and nitrate concentration accounted for much of the major shifts in microbial sequence abundance during the co-composting process.

Real-time PCR quantification of arbuscular mycorrhizal fungi: does the use of nuclear or mitochondrial markers make a difference?

Root colonization by arbuscular mycorrhizal fungi (AMF) can be quantified by different approaches. We compared two approaches that enable discrimination of specific AMF taxa and are therefore emerging as alternative to most commonly performed microscopic quantification of AMF in roots: quantitative real-time PCR (qPCR) using markers in nuclear ribosomal DNA (nrDNA) and mitochondrial ribosomal DNA (mtDNA). In a greenhouse experiment, Medicago truncatula was inoculated with four isolates belonging to different AMF species (Rhizophagus irregularis, Claroideoglomus claroideum, Gigaspora margarita and Funneliformis mosseae). The AMF were quantified in the root samples by qPCR targeted to both markers, microscopy and contents of AMF-specific phospholipid fatty acids (PLFA). Copy numbers of nrDNA and mtDNA were closely related within all isolates; however, the slopes and intercepts of the linear relationships significantly differed among the isolates. Across all isolates, a large proportion of variance in nrDNA copy numbers was explained by root colonization intensity or contents of AMF-specific PLFA, while variance in mtDNA copy numbers was mainly explained by differences among AMF isolates. We propose that the encountered inter-isolate differences in the ratios of mtDNA and nrDNA copy numbers reflect different physiological states of the isolates. Our results suggest that nrDNA is a more suitable marker region than mtDNA for the quantification of multiple AMF taxa as its copy numbers are better related to fungal biomass across taxa than are copy numbers of mtDNA.

Microbial community structure and diversity in a municipal solid waste landfill

Municipal solid waste (MSW) landfills are the most prevalent waste disposal method and constitute one of the largest sources of anthropogenic methane emissions in the world. Microbial activities in disposed waste play a crucial role in greenhouse gas emissions; however, only a few studies have examined metagenomic microbial profiles in landfills. Here, the MiSeq high-throughput sequencing method was applied for the first time to examine microbial diversity of the cover soil and stored waste located at different depths (0-150cm) in a typical MSW landfill in Yangzhou City, East China. The abundance of microorganisms in the cover soil (0-30cm) was the lowest among all samples, whereas that in stored waste decreased from the top to the middle layer (30-90cm) and then increased from the middle to the bottom layer (90-150cm). In total, 14 phyla and 18 genera were found in the landfill. A microbial diversity analysis showed that Firmicutes, Proteobacteria, and Bacteroidetes were the dominant phyla, whereas Halanaerobium, Methylohalobius, Syntrophomonas, Fastidiosipila, and Spirochaeta were the dominant genera. Methylohalobius (methanotrophs) was more abundant in the cover layers of soil than in stored waste, whereas Syntrophomonas and Fastidiosipila, which affect methane production, were more abundant in the middle to bottom layers (90-150cm) in stored waste. A canonical correlation analysis showed that microbial diversity in the landfill was most strongly correlated with the conductivity, organic matter, and moisture content of the stored waste.

Primary sources and toxicity of PAHs in Milwaukee-area streambed sediment

High concentrations of polycyclic aromatic hydrocarbons (PAHs) in streams can be a significant stressor to aquatic organisms. To understand the likely sources and toxicity of PAHs in Milwaukee-area streams, streambed sediment samples from 40 sites and parking lot dust samples from 6 sites were analyzed for 38 parent PAHs and 25 alkylated PAHs. Diagnostic ratios, profile correlations, principal components analysis, source-receptor modeling, and mass fractions analysis were used to identify potential PAH sources to streambed sediment samples, and land-use analysis was used to relate streambed sediment PAH concentrations to different urban-related land uses. On the basis of this multiple lines-of-evidence approach, coal-tar pavement sealant was indicated as the primary source of PAHs in a majority of streambed sediment samples, contributing an estimated 77% of total PAHs to samples, on average. Comparison with the probable effect concentrations and (or) the equilibrium partitioning sediment benchmark indicates that 78% of stream sediment samples are likely to cause adverse effects to benthic organisms. Laboratory toxicity tests on a 16-sample subset of the streambed sites using the amphipod Hyalella azteca (28-d) and the midge Chironomus dilutus (10-d) measured significant reductions in 1 or more biological endpoints, including survival, in 75% of samples, with H. azteca more responsive than C. dilutus. Environ Toxicol Chem 2017;36:1622-1635. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC.

Bioremediation of long-term PCB-contaminated soil by white-rot fungi

The objective of this work was to test the PCB-degrading abilities of two white-rot fungi, namely Pleurotus ostreatus and Irpex lacteus, in real contaminated soils with different chemical properties and autochthonous microflora. In addition to the efficiency in PCB removal, attention was given to other important parameters, such as changes in the toxicity and formation of PCB transformation products. Moreover, structural shifts and dynamics of both bacterial and fungal communities were monitored using next-generation sequencing and phospholipid fatty acid analysis. The best results were obtained with P. ostreatus, which resulted in PCB removals of 18.5, 41.3 and 50.5% from the bulk, top (surface) and rhizosphere, respectively, of dumpsite soils after 12 weeks of treatment. Numerous transformation products were detected (hydoxylated and methoxylated PCBs, chlorobenzoates and chlorobenzyl alcohols), which indicates that both fungi were able to oxidize and decompose the aromatic moiety of PCBs in the soils. Microbial community analysis revealed that P. ostreatus efficiently colonized the soil samples and suppressed other fungal genera. However, the same fungus substantially stimulated bacterial taxa that encompass putative PCB degraders. The results of this study finally demonstrated the feasibility of using this fungus for possible scaled-up bioremediation applications.

Exploring the potential of fungi isolated from PAH-polluted soil as a source of xenobiotics-degrading fungi

The aim of this study was to find polycyclic aromatic hydrocarbon (PAH)-degrading fungi adapted to polluted environments for further application in bioremediation processes. In this study, a total of 23 fungal species were isolated from a historically pyrogenic PAH-polluted soil in Spain and taxonomically identified. The dominant groups in these samples were the ones associated with fungi belonging to the Ascomycota phylum and two isolates belonging to the Mucoromycotina subphylum and Basiodiomycota phylum. We tested their ability to convert the three-ring PAH anthracene in a 42-day time course and analysed their ability to secrete extracellular oxidoreductase enzymes. Among the 23 fungal species screened, 12 were able to oxidize anthracene, leading to the formation of 9,10-anthraquinone as the main metabolite, a less toxic one than the parent compound. The complete removal of anthracene was achieved by three fungal species. In the case of Scopulariopsis brevicaulis, extracellular enzyme independent degradation of the initial 100 μM anthracene occurred, whilst in the case of the ligninolytic fungus Fomes (Basidiomycota), the same result was obtained with extracellular enzyme-dependent transformation. The yield of accumulated 9,10-anthraquinone was 80 and 91 %, respectively, and Fomes sp. could slowly deplete it from the growth medium when offered alone. These results are indicative for the effectiveness of these fungi for pollutant removal. Graphical abstract ᅟ.