Enabling simultaneous redox transformation of toxic chromium(VI) and arsenic(III) in aqueous media-A review

Is Pyrolysis Treatment a Viable Solution to Detoxify Metal(loid)s in Sewage Sludge toward Land Application? Case Studies of Chromium and Zinc

Metal(loid)s in sewage sludge (SS) are effectively immobilized after pyrolysis. However, the bioavailability and fate of the immobilized metal(loid)s in SS-derived biochar (SSB) following land application remain largely unknown. Here, the speciation and bioavailability evolution of SSB-borne Cr and Zn in soil were systematically investigated by combining pot and field trials and X-ray absorption spectroscopy. Results showed that approximately 58% of Cr existing as Cr(III)-humic complex in SS were transformed into Fe (hydr)oxide-bound Cr(III), while nano-ZnS in SS was transformed into stable ZnS and ferrihydrite-bound species (accounting for over 90% of Zn in SSB) during pyrolysis. All immobilized metal(loid)s, including Cr and Zn, in SSB tended to be slowly remobilized during aging in soil. This study highlighted that SSB acted as a dual role of source and sink of metal(loid)s in soil and posed potential risks by serving a greater role of a metal(loid) source than a sink when applied to uncontaminated soils. Nevertheless, SSB could impede the translocation of metal(loid)s from soil to crop compared to SS, where coexisting elements, including Fe, P, and Zn, played critical roles. These findings provide new insights for understanding the fate of SSB-borne metal(loid)s in soil and assessing the viability of pyrolyzing SS for land application.

Influence of tartaric acid on the electron transfer between oxyanions and lepidocrocite

Iron oxide minerals control the environmental behavior of trace elements. However, the potential effects of electron transfer directions by iron oxides between organic acids and trace elements remain unclear. This study investigates the redox capacity of tartaric acid (TA) with chromate (Cr(Ⅵ)) or arsenate (As(V)) on lepidocrocite (Lep) from the perspective of electron transfer. The results demonstrated the configurations of TA (bidentate binuclear (BB)), As(V) (BB), and Cr(Ⅵ) (BB and protonated monodentate binuclear (HMB)) on Lep. Frontier molecular orbital calculations and X-ray photoelectron spectroscopy (XPS) binding energy shifts further indicated different electron transfer directions between TA and the oxyanions on Lep. The iron of Lep might act as electron acceptors when TA is adsorbed, whereas the iron and oxygen of Lep act as electron donors when As(V) is adsorbed. The iron of Lep might accept electrons from its oxygen and subsequently transfer these electrons to Cr(Ⅵ). Macroscopic validation experiments showed the reduction of Cr(VI), whereas no reduction of As(V). The XPS analysis showed a peak shift, with the possible formation of As-Fe-TA ternary complexes and electron transfer on Lep. These findings indicate that mineral interfacial electron transfer considerably influences the transport and transformation of oxyanions.

A comprehensive study about functionalization and de-functionalization of MOF-808 as a defect-engineered Zr-MOFs for selective catalytic oxidation

In metal-organic frameworks (MOFs), confined space as a chemical nanoreactor is as essential as coordinatively unsaturated metal site catalysis. The properties of MOFs can be adjusted through the incorporation of functional groups and open metal sites in frameworks that can modify the catalytic performance. In this regard, a set of defect-engineered MOFs, Ex-MOF-808(NH2, NO2, H) and Mix-MOF-808(NH2, NO2, H), were synthesized by ultrasonic-assisted linker exchange approach (Ex-MOFs) and solvothermal mixing ligand method (Mix-MOFs), respectively. Further, the relationship between the preparation method, structural properties, and catalytic efficiency of the prepared materials in the selective oxidation of methyl phenyl sulfide (MPS) has been investigated. By analyzing zeta potential, it was found that in the exchange method, the amount of defect and functional groups on the surface of MOFs are more than in the mixing method, which also affects the catalytic activity. In our contribution, mix-MOF-808(NO2) carrying nitro groups at their organic linkers, which has a well-dispersion of nitro groups at the framework exhibits selective conversion of MPS to sulfone (91 %). Furthermore, the performance of stable heterogeneous catalysts was investigated for three cycles, which demonstrated their great potential for advanced catalytic oxidation.

Unravelling the removal mechanisms of trivalent arsenic by sulfidated nanoscale zero-valent iron: The crucial role of reactive oxygen species and the multiple effects of citric acid

The remediation of arsenic-contaminated groundwater by sulfidated nanoscale zero-valent iron (S-nZVI) has raised considerable attention. However, the role of trivalent arsenic (As(III)) oxidation by S-nZVI in oxic conditions (S-nZVI/O2) remains controversial, and the comprehensive effect of citric acid (CA) prevalent in groundwater on As(III) removal by S-nZVI remains unclear. Herein, the mechanisms of reactive oxygen species (ROS) generation and multiple effects of CA on As(III) removal by S-nZVI/O2 were systematically explored. Results indicated that the removal efficiency of As(III) by S-nZVI/O2 (97.81 %) was prominently higher than that by S-nZVI (66.71 %), resulting from the significant production of ROS (mainly H2O2 and OH) under oxic conditions, which played a crucial role in promoting the As(III) oxidation. Additionally, CA had multiple effects on As(III) removal by S-nZVI/O2 system: (i) CA impeded the diffusion of As(III) towards S-nZVI and increased the secondary risk of immobilized As(III) re-releasing into the environment due to the Fe dissolution from S-nZVI; (ii) CA could significantly enhance the yields of OH from 25.29 to 133.00 μM via accelerating the redox cycle of Fe(II)/Fe(III) and increasing the oriented conversion rate of H2O2 to OH; (iii) CA could also enrich the types of ROS (such as O2- and 1O2) in favor of further As(III) oxidation. This study contributed novel findings regarding the control of As(III) contaminated groundwater using S-nZVI technologies.

Enhanced Cr(VI) stabilization by terrestrial-derived soil protein: Photoelectrochemical properties and reduction mechanisms

Glomalin-related soil protein (GRSP) is a stable iron-organic carbon mixture that can enhance heavy metal sequestration in soils. However, the roles of GRSP in the transformation and fate of Cr(VI) have been rarely reported. Herein, we investigated the electrochemical and photocatalytic properties of GRSP and its mechanisms in Cr(VI) adsorption and reduction. Results showed that GRSP had a stronger ability for Cr(VI) adsorption and reduction than other biomaterials, with the highest adsorption amount of up to 0.126 mmol/g. The removal efficiency of Cr(VI) by GRSP was enhanced (4-7%) by ultraviolet irradiation due to the hydrated electrons produced by GRSP. Fe(II) ions, persistent free radicals, and oxygen-containing functional groups on the GRSP surface as electron donors participated in the reduction of Cr(VI) under dark condition. Moreover, Cr(III) was mainly adsorbed on the -COOH groups of GRSP via electrostatic interactions. Based on 2D correlation spectroscopy, the preferential adsorption occurred on the GRSP surface for Cr(VI) in the sequential order of CO → COO- → O-H → C-O. This work provides new insights into the Cr(VI) adsorption and reduction mechanism by GRSP. Overall, GRSP can serve as a natural iron-organic carbon for the photo-reduction of Cr(VI) pollution in environments.

Ball-milled zero-valent iron with formic acid for effectively removing Cu(II)-EDTA accomplished by EDTA ligands oxidative degradation and Cu(II) removal

Heavy metal complexes in industrial wastewater are challenging to be removed by conventional methods arising from their stable chelating structure. In this study, zero-valent iron (ZVI) was ball-milled with tiny formic acid (FA), and the as-prepared sample (FA-ZVIbm) was attempted to eliminate a model heavy metal complex of Cu(II)-ethylenediaminetetraacetic acid (Cu(II)-EDTA). The addition of FA to ball-milling could dramatically enhance the performance of ball-milled ZVI (ZVIbm) towards Cu(II)-EDTA removal and increase the removal rate constant by 80 times. This conspicuous improvement of Cu(II)-EDTA elimination was attributed to the ferrous formate (Fe(HCOO)2) shell formed on the surface of FA-ZVIbm. Results revealed that the Fe(HCOO)2 shell facilitated the activation of O2 to reactive oxygen species (ROS) and the leaching of Fe3+. Cu(II)-EDTA was decomplexed through both oxidative destruction and Fe3+ replacement, and the released Cu2+ was reduced by FA-ZVIbm and immobilized synchronously. Meanwhile, the ligands underwent oxidative degradation by ROS, thus avoiding the re-chelation ecological risk. Impressively, FA-ZVIbm could achieve cyclic treatment of actual copper complex wastewater and possessed promising advantage in treatment cost. This study would offer a promising approach for eliminating Cu(II)-EDTA through EDTA ligands degradation and synchronous Cu(II) removal, moreover to shed light on the decomplexation mechanism.

Production of extracellular superoxide radical in microorganisms and its environmental implications: A review

Extracellular superoxide radical (O2•-) is ubiquitous in microbial environments and has significant implications for pollutant transformation. Microbial extracellular O2•- can be produced through multiple pathways, including electron leakage from the respiratory electron transport chain (ETC), NADPH oxidation by the transmembrane NADPH oxidase (NOX), and extracellular reactions. Extracellular O2•- significantly influences the geochemical processes of various substances, including toxic metals and refractory organic pollutants. On one hand, extracellular O2•- can react with variable-valence metals and detoxify certain highly toxic metals, such as As(III), Cr(VI), and Hg(II). On the other hand, extracellular O2•- can directly or indirectly (via Bio-Fenton) degrade many organic pollutants, including a variety of emerging contaminants. In this work, we summarize the production mechanisms of microbial extracellular O2•-, review its roles in the transformation of environmental pollutants, and discuss the potential applications, limiting factors, and future research directions in this field.

Enhanced immobilization of Arsenic(III) and Auto-oxidation to Arsenic(V) by titanium oxide (TiO2), due to Single-Atom vacancies and oxyanion formation

Pollution control of As(III), a naturally occurring carcinogen, has recently gained a global attention, while due to the dominance of neutral H3AsO3 over a wide pH range, As(III) immobilization by most minerals is not efficient as As(V) immobilization. TiO2 shows promise for controlling As(III) pollution, and herein, a comprehensive study about As(III) adsorption by TiO2 and oxyanion formation is conducted by means of DFT + D3 methods. Both anatase and rutile are effective for As(III) adsorption, while As(III) adsorption affinities differ significantly and are -1.48 and -3.79 eV for pristine surfaces, ascend to -3.85 and -5.08 eV for O vacancies, and further to -5.37 and -5.26 eV for Ti vacancies, respectively. The bidentate binuclear complexes dominate for pristine surfaces, and O vacancies prefer OAs insertion into TiO2 lattice, while for Ti vacancies, all As(III) centers are auto-oxidized to As(V). Ti-3d, O-2p or/and As-4p rather than other orbitals contribute significantly to As adsorption, and O and Ti vacancies promote adsorption through stronger orbital hybridization. The superior adsorption for Ti vacancies originates from As(V) formation instead of bonding interactions. The formation of As oxyanions, which may occur spontaneously at pristine surfaces and is greatly promoted by O and Ti vacancies, enhances As(III) adsorption pronouncedly and becomes a viable strategy for As(III) immobilization. H2AsO3- and HAsO32- dominate for pristine surfaces and O vacancies, and for Ti vacancies, H2AsO4- and HAsO42- dominate over anatase whereas AsO43- also makes an important contribution over rutile. Results rationalize experimental observations available, and provide significantly new insights about the migration, bioavailability and fate of As(III) over TiO2 surfaces that facilitate the exploration of scavengers for As and other pollutants.

Electrically Controlled Adsorptive Membranes with Tunable Affinity for Selective Chromium (VI) Separation from Water

Ionic contaminants such as Cr(VI) pose a challenge for water purification using membrane-based processes. However, existing membranes have low permeability and selectivity for Cr(VI). Therefore, in this study, we prepared an electrically controlled adsorptive membrane (ECAM-L) by coating a loose Cl--doped polypyrrole layer on a carbon nanotube substrate, and we evaluated the performance of ECAM-L for Cr(VI) separation from water. We also used electrochemical quartz crystal microbalance measurements and molecular dynamics and density functional theory calculations to investigate the separation mechanisms. The adsorption and desorption of Cr(VI) could be modulated by varying the electrostatic interactions between ECAM-L and Cr(VI) via potential control, enabling the cyclic use of the ECAM-L without additional additives. Consequently, the oxidized ECAM-L showed high Cr(VI) removal performance (<50 μg/L) and treatment capacity (>3500 L/m2) at a high water flux (283 L/m2/h), as well as reusability after the application of a potential. Our study demonstrates an efficient membrane design for water decontamination that can selectively separate Cr(VI) through a short electric stimulus.

Effective assessment of biopolymer-based multifunctional sorbents for the remediation of environmentally hazardous contaminants from aqueous solutions

Persistent contaminants in wastewater effluent pose a significant threat to aquatic life and are one of the most significant environmental concerns of our time. Although there are a variety of traditional methods available in wastewater treatment, including adsorption, coagulation, flocculation, ion exchange, membrane filtration, co-precipitation and solvent extraction, none of these have been found to be significantly cost-effective in removing toxic pollutants from the water environment. The upfront costs of these treatment methods are extremely high, and they require the use of harmful synthetic chemicals. For this reason, the development of new technologies for the treatment and recycling of wastewater is an absolute necessity. Our way of life can be made more sustainable by the synthesis of adsorbents based on biomass, making the process less harmful to the environment. Biopolymers offer a sustainable alternative to synthetic polymers, which are manufactured by joining monomer units through covalent bonding. This review presents a detailed classification of biopolymers such as pectin, alginate, chitosan, lignin, cellulose, chitin, carrageen, certain proteins, and other microbial biomass compounds and composites, with a focus on their sources, methods of synthesis, and prospective applications in wastewater treatment. A concise summary of the extensive body of knowledge on the fate of biopolymers after adsorption is also provided. Finally, consideration is given to open questions about future developments leading to environmentally friendly and economically beneficial applications of biopolymers.

Investigation of TiO2 Deposit on SiO2 Films: Synthesis, Characterization, and Efficiency for the Photocatalytic Discoloration of Methylene Blue in Aqueous Solution

TiO₂-SiO₂ thin films were created on Corning glass substrates using a simple method. Nine layers of SiO₂ were deposited; later, several layers of TiO₂ were deposited, and their influence was studied. Raman spectroscopy, high resolution transmission electron spectroscopy (HRTEM), an X-ray diffractometer (XRD), ultraviolet-visible spectroscopy (UV-Vis), a scanning electron microscope (SEM), and atomic force microscopy (AFM) were used to describe the sample's shape, size, composition, and optical characteristics. Photocatalysis was realized through an experiment involving the deterioration of methylene blue (MB) solution exposed to UV-Vis radiation. With the increase of TiO₂ layers, the photocatalytic activity (PA) of the thin films showed an increasing trend, and the maximum degradation efficiency of MB by TiO₂-SiO₂ was 98%, which was significantly higher than that obtained by SiO₂ thin films. It was found that an anatase structure was formed at a calcination temperature of 550 °C; phases of brookite or rutile were not observed. Each nanoparticle's size was 13-18 nm. Due to photo-excitation occurring in both the SiO₂ and the TiO₂, deep UV light (λ = 232 nm) had to be used as a light source to increase photocatalytic activity.

Roles of humic substances redox activity on environmental remediation

Humic substances (HS) as representative natural organic matters and the most common organic compounds existing in the environment, has been applied to the treatment and remediation of environmental pollution. This review systematically introduces and summarizes the redox activity of HS for the remediation of environmental pollutants. For inorganic pollutants (such as silver, chromium, mercury, and arsenic), the redox reaction of HS can reduce their toxicity and mobilization, thereby reducing the harm of these pollutants to the environment. The concentration and chemical composition of HS, environmental pH, ionic strength, and competing components affect the degree and rate of redox reactions between inorganic pollutants and HS significantly. With regards to organic pollutants, HS has photocatalytic activity and produces a large number of reactive oxygen species (ROS) under the light which reacts with organic pollutants to accelerate the degradation of organic pollutants. Under the affection of HS, the redox of Fe(III) and Fe(II) can enhance the efficiency of Fenton-like reaction to degrade organic pollutants. Finally, the research direction of HS redox remediation of environmental pollution is prospected.

Reductive Removal and Recovery of As(V) and As(III) from Strongly Acidic Wastewater by a UV/Formic Acid Process

The removal of arsenic (As(V) and As(III)) from strongly acidic wastewater using traditional neutralization or sulfuration precipitation methods produces a large amount of arsenic-containing hazardous wastes, which poses a potential threat to the environment. In this study, an ultraviolet/formic acid (UV/HCOOH) process was proposed to reductively remove and recover arsenic from strongly acidic wastewater in the form of valuable elemental arsenic (As(0)) products to avoid the generation of hazardous wastes. We found that more than 99% of As(V) and As(III) in wastewater was reduced to highly pure solid As(0) (>99.5 wt %) by HCOOH under UV irradiation. As(V) can be efficiently reduced to As(IV) (H₂AsO₃ or H₄AsO₄) by hydrogen radicals (H^•) generated from the photolysis of HCOOH through dehydroxylation or hydrogenation. Then, As(IV) is reduced to As(III) by H^• or through its disproportionation. The reduction of As(V) to H₄AsO₄ by H^• and the disproportionation of H₄AsO₄ are the main reaction processes. Subsequently, As(III) is reduced to As(0) not only by H^• through stepwise dehydroxylation but also through the disproportionation of intermediate arsenic species As(II) and As(I). With additional density functional theory calculations, this study provides a theoretical foundation for the reductive removal of arsenic from acidic wastewater.

Arsenate and arsenite differential toxicity in Tetrahymena thermophila

A comparative analysis of toxicities of both arsenic forms (arsenite and arsenate) in the model eukaryotic microorganism Tetrahymena thermophila (ciliate protozoa) has shown the presence of various detoxification mechanisms and cellular effects comparable to those of animal cells under arsenic stress. In the wild type strain SB1969 arsenate is almost 2.5 times more toxic than arsenite. According to the concentration addition model used in binary metallic mixtures their toxicities show an additive effect. Using fluorescent assays and flow cytometry, it has been detected that As(V) generates elevated levels of ROS/RNS compared to As(III). Both produce the same levels of superoxide anion, but As(V) also causes greater increases in hydrogen peroxide and peroxynitrite. The mitochondrial membrane potential is affected by both As(V) and As(III), and electron microscopy has also revealed that mitochondria are the main target of both arsenic ionic forms. Fusion/fission and swelling mitochondrial and mitophagy, together with macroautophagy, vacuolization and mucocyst extruction are mainly associated to As(V) toxicity, while As(III) induces an extensive lipid metabolism dysfunction (adipotropic effect). Quantitative RT-PCR analysis of some genes encoding antioxidant proteins or enzymes has shown that glutathione and thioredoxin metabolisms are involved in the response to arsenic stress. Likewise, the function of metallothioneins seems to be crucial in arsenic detoxification processes, after using both metallothionein knockout and knockdown strains and cells overexpressing metallothionein genes from this ciliate. The analysis of the differential toxicity of As(III) and As(V) shown in this study provides cytological and molecular tools to be used as biomarkers for each of the two arsenic ionic forms.

Enhanced degradation of sulfamethoxazole by a modified nano zero-valent iron with a β-cyclodextrin polymer: Mechanism and toxicity evaluation

Rising concern about emerging and already persisting pollutants in water has urged the scientific community to develop novel remedial techniques. A new group of remediation methods is based on the modification of nanoscale zero-valent iron particles (nZVI), which are well known for treating volatile organic compounds and heavy metals. The properties of nZVI may be further enhanced by modifying their structure or surface using "green" polymers. Herein, nZVI was modified by a β-cyclodextrin polymer (β-CDP), which is considered an environmentally safe and inexpensive adsorbent of contaminants. This composite was used for the first time for the degradation of sulfamethoxazole (SMX). Coating by β-CDP not only enhanced the degradation of SMX (>95%, under 10 min) by the nanoparticles in a wide pH range (3-9) and enabled their efficient reusability (for three cycles) but also made the coated nZVI less toxic to the model bioindicator microalga Raphidocelis subcapitata. Moreover, degradation products of SMX were found to be less toxic to Escherichia coli bacteria and R. subcapitata microalga, contrary to the SMX antibiotic itself, indicating a simple and eco-friendly cleaning process. This research aims to further stimulate and develop novel remedial techniques based on nZVI, and provides a potential application in the degradation of antibiotics in a wide pH range. Moreover, the wealth of available cyclodextrin materials used for surface modification may open a way to discover more efficient and attractive composites for environmental applications.

Adsorption and photocatalysis removal of arsenite, arsenate, and hexavalent chromium in water by the carbonized composite of manganese-crosslinked sodium alginate

The preparation of easily synthesized and cheap composite materials for the efficient removal of toxic oxoanions still remains challenging in sewage treatment. Herein, a new carbonized manganese-crosslinked sodium alginate (Mn/SA-C) was fabricated for the removal of arsenite (As(III)), arsenate (As(V)) and hexavalent chromium (Cr(VI)) in water. The results indicated that the Mn/SA-C pretreated with MnSO₄ solution (Mn/SA-C-S) exhibited a rapid adsorption toward As(III) and As(V) with the removal efficiency of >98% within 10 min, and had a high adsorption capacity toward As(III), As(V), and Cr(VI) with the maximum value of 189.29, 193.29, and 104.50 mg/g based on the Langmuir model, respectively. The removal efficiency of As(III), As(V), and Cr(VI) could be further significantly enhanced by coupling a photocatalytic process. For example, the time in which >98% of Cr(VI) (10 mg/L) was removed dramatically shortened from 360 min (adsorption) to 45 min (adsorption-photocatalysis), and the removal efficiency of As(III) increased by ∼10% within initial 5 min. This was primarily attributed to the Mn-catalyzed production of the photocatalytic excitons for Cr(VI) reduction, and the superoxide (•O₂^-) and hydroxyl (•OH) radicals for As(III) oxidation. The adsorption removal of arsenic (As) was primarily ascribed to surface complexation with MnO and precipitation by MnS₂, and oxidative adsorption because of Mn valence cycle. The removal mechanisms of Cr(VI) mainly contained reduction by MnO and MnS₂, complexation with MnO and carboxyl/hydroxyl groups as well as Cr(OH)₃ precipitation. Our research provides a promising Mn/SA-C-S material for rapid and efficient removal of As(III), As(V), and Cr(VI) in contaminated water through an adsorption-photocatalysis synergistic strategy.

Fabrication of a novel heteroepitaxial structure from an MOF-on-MOF architecture as a photocatalyst for highly efficient Cr(vi) reduction

Ce-on-Zr-MOF-808, a novel MOF-on-MOF hybrid used for efficient chromium reduction under visible-light irradiation.

Pseudocitrobacter anthropi reduces heavy metal uptake and improves phytohormones and antioxidant system in Glycine max L

Heavy metal contamination due to anthropogenic activities is a great threat to modern humanity. A novel and natural technique of bioremediation using microbes for detoxification of heavy metals while improving plants' growth is the call of the day. In this study, exposing soybean plants to different concentrations (i.e., 10 and 50 ppm) of chromium and arsenic showed a severe reduction in agronomic attributes, higher reactive oxygen species production, and disruption in the antioxidant system. Contrarily, rhizobacterial isolate C18 inoculation not only rescued host growth, but also improved the production of nonenzymatic antioxidants (i.e., flavonoids, phenolic, and proline contents) and enzymatic antioxidants i.e., catalases, ascorbic acid oxidase, peroxidase activity, and 1,1-diphenyl-2-picrylhydrazyl, lower reactive oxygen species accumulation in leaves. Thereby, lowering secondary oxidative stress and subsequent damage. The strain was identified using 16 S rDNA sequencing and was identified as Pseudocitrobacter anthropi. Additionally, the strain can endure metals up to 1200 ppm and efficient in detoxifying the effect of chromium and arsenic by regulating phytohormones (IAA 59.02 µg/mL and GA 101.88 nM/mL) and solubilizing inorganic phosphates, making them excellent phytostimulant, biofertilizers, and heavy metal bio-remediating agent.