Photoelectrocatalytic technologies for environmental applications

Electrochemical filtration for drinking water purification: A review on membrane materials, mechanisms and roles

Electrochemical filtration can not only enrich low concentrations of pollutants but also produce reactive oxygen species to interact with toxic pollutants with the assistance of a power supply, making it an effective strategy for drinking water purification. In addition, the application of electrochemical filtration facilitates the reduction of pretreatment procedures and the use of chemicals, which has outstanding potential for maximizing process simplicity and reducing operating costs, enabling the production of safe drinking water in smaller installations. In recent years, the research on electrochemical filtration has gradually increased, but there has been a lack of attention on its application in the removal of low concentrations of pollutants from low conductivity water. In this review, membrane substrates and electrocatalysts used to improve the performance of electrochemical membranes are briefly summarized. Meanwhile, the application prospects of emerging single-atom catalysts in electrochemical filtration are also presented. Thereafter, several electrochemical advanced oxidation processes coupled with membrane filtration are described, and the related working mechanisms and their advantages and shortcomings used in drinking water purification are illustrated. Finally, the roles of electrochemical filtration in drinking water purification are presented, and the main problems and future perspectives of electrochemical filtration in the removal of low concentration pollutants are discussed.

Advances on electrochemical disinfection research: Mechanisms, influencing factors and applications

Disinfection, a vital barrier against pathogenic microorganisms, is crucial in halting the spread of waterborne diseases. Electrochemical methods have been extensively researched and implemented for the inactivation of pathogenic microorganisms from water and wastewater, primarily owing to their simplicity, efficiency, and eco-friendliness. This review succinctly outlined the core mechanisms of electrochemical disinfection (ED) and systematically examined the factors influencing its efficacy, including anode materials, system conditions, and target species. Additionally, the practical application of ED in water and wastewater treatment was comprehensively reviewed. Case studies involving various scenarios such as drinking water, hospital wastewater, black water, rainwater, and ballast water provided concrete instances of the expansive utility of ED. Finally, coupling ED with other technologies and the resulting synergies were introduced as pivotal foundations for subsequent engineering advancements.

Effluent toxicity study using biomarkers for ciprofloxacin photoelectrocatalytic degradation by bismuth-doped titanium dioxide nanotubes

Ciprofloxacin hydrochloride (CIP) is a broad-spectrum synthetic antibiotic often found in domestic sewage and industrial waste due to the inefficiency of conventional treatments. Given the potential risk of drug accumulation, this study presents coatings of titanium dioxide nanotubes (TiO2) doped with different bismuth (Bi) concentrations to degrade CIP through photocatalytic and photoelectrochemical processes. Characterization studies revealed that bismuth (Bi) doping affected the morphology of the materials, with concentrations of 0.01 and 0.05 mol L-1, resulting in collapsed materials with a smaller active surface area. Photocatalysis tests for all the materials exhibited a similar degree of efficiency to photolysis, approximately 33%. Ecotoxicity tests using the biomarkers Lactuca sativa L., Lemna minor, and Artemia salina indicated that, although they were similar to photolysis in terms of efficiency, the effluents generated when employing the doped catalysts showed lower levels of toxicity, with the best results achieved for the material doped with 0.005 mol L-1 of Bi, with a toxicity level approximately 40% lower. Photoelectrocatalysis proved to be the most efficient CIP degradation technique. The highest degradation rate was observed for materials doped with 0.005 mol L-1 of Bi, with an efficiency of 46%, which is 1.4 times more efficient than photolysis. These results demonstrate that materials doped with low amounts of Bi can be effectively used as photoanodes for drug degradation, as their performance is superior, and the final product generated exhibits low toxicity to living organisms.

Photo-electrochemical oxidation flow system for stormwater herbicides removal: Operational conditions and energy consumption analysis

Photoelectrochemical oxidation (PECO) is a promising advanced technology for treating micropollutants in stormwater. However, it is important to understand its operation prior to practical validation. In this study, we introduced a flow PECO system designed to evaluate its potential for full-scale applications in herbicides degradation, providing valuable insights for future large-scale implementations. The PECO flow reactor demonstrated the ability to treat a larger volume of stormwater (675 mL, approximately 10 times more than previous batch experiments) with effective removal rates of 92 % for diuron and 22 % for atrazine over 6 h of operation at 2 V. To address the large volume issue in stormwater treatment, a multiple module parallel application design is being considered to increase the treatment capacity of the PECO flow reactor. During the flow reactor operations, flow rate was found to have a notable impact on removal performance, particularly for diuron. At a flow rate of 610 mL min-1, approximately 90 % removal of diuron was achieved, while at 29 mL min-1, the removal efficiency decreased to 60 %. While light intensity had minimal effect on diuron degradation (all settings achieved over 90 % removal), it enhanced atrazine degradation from 9 % to 31 % with an increase in intensity from 63 mW cm-2 to 144 mW cm-2. Remarkably, the PECO flow system exhibited excellent removal performance (>90 % removal) for diuron even at extremely high initial pollutant concentrations (240 μg L-1), demonstrating its capacity to handle varying contaminant loads in stormwater. Energy consumption analysis revealed that flow rate as the primary factor influenced the specific energy consumption rate. Higher flow rate (e.g., 610 mL min-1) were preferable in flow reactor due to its well-balanced performance between removal and energy consumption. These findings confirm that the PECO flow system offers an efficient and promising approach for stormwater treatment applications.

Mesostructured lead dioxide grown on titania nanotubes for diclofenac water removal through electrocatalytic and photoelectrocatalytic processes

Mesostructured PbO2/TiO2 materials were synthesized to perform electrocatalysis (as electrooxidation, EO) and photoelectrocatalysis for removing diclofenac (DCF), 15 ppm concentration in 0.1 M NaSO4 solutions, at different pH conditions (3.0, 6.0 and 9.0) by applying 30 mA cm-2. Titania nanotubes (TiO2NTs)-based materials were prepared to synthetize with a massive PbO2 deposit on this support to obtain TiO2NTs/PbO2 and a TiO2NTs:PbO2 material consisting in a dispersed PbO2 deposit on TiO2-NTs that allowed the formation of a heterostructured surface of combined composition (TiO2 and PbO2). Organics removal (DCF and byproducts) was monitored through UV-vis spectrophotometry and high-performance liquid chromatography (HPLC) during degradation tests. TiO2NTs/PbO2 electrode was tested in both processes, removing DCF at neutral and alkaline solution conditions in EO while an unimportant photoactivity was registered at this material. Conversely, TiO2NTs:PbO2 was used as electrocatalytic material in EO experiments, achieving more than 50% of DCF removal at pH 6.0 by applying 30 mA cm-2. Also, for first time, the synergic effect was investigated when it was exposed to UV irradiation in photoelectrocatalytic experiments, enhancing its efficacy (⁓more than 20%) to remove DCF from a solution with 15 ppm over performance removals achieved (56%) when EO was applied under similar conditions. Chemical Oxygen Demand (COD) analyses showed that significantly higher DCF degradation is reached under photoelectrocatalysis, since COD values decrease a 76% against a 42% decrease achieved with electrocatalysis. Scavenging experiments showed a significant participation on the pharmaceutical oxidation process through the generation of photoholes (h+), hydroxyl radicals and sulfate-based oxidants.

Norfloxacin mineralization under light exposure using Sb-SnO2 ceramic anodes coated with BiFeO3 photocatalyst

Advanced Oxidation Processes have been proven to be an efficient way to remove organic pollutants from wastewaters. In this work, a ceramic electrode of Sb-SnO₂ (BCE) with a layer of the photocatalytic material BiFeO₃ (BFO-BCE), has been characterized electrochemically and further tested for norfloxacin photo-electrooxidation in the presence and absence of light. The electrode photoactivity was highly enhanced thanks to the presence of BiFeO₃, as confirmed by Linear Sweep Voltammetry, chronoamperometry and potentiometry, and Electrochemical Impedance Spectroscopy. Additionally, working in galvanostatic mode, a high mineralization of norfloxacin was achieved after 240 min, reaching 62% at 25 mA cm^-2 under light conditions. This value is comparatively higher than the 40% achieved with the BCE. The oxidation byproducts were followed by ionic chromatography and HPLC analysis, which also allowed us to propose an oxidation pathway of the norfloxacin molecule. Finally, some indicators of the reactor performance such as the Mineralization Current Efficiency and the specific energy consumption were analyzed, revealing that lower current densities (8.3 mA cm^-2) led to higher current efficiencies, and that light improved both the current efficiency and energy consumption.

Photocatalytic degradation of triclocarban in aqueous solution using a modified zeolite/TiO2 composite: kinetic, mechanism study and toxicity assessment

The current work aimed to investigate the degradation of the triclocarban (TCC) in aqueous solution using a modified zeolite/TiO₂ composite (MZTC) synthesized by applying the electrochemical anodization (ECA). The synthesis process was conducted at different voltages (10, 40, and 60) V in 1 h and using electrophoresis deposition (EPD) in doping zeolite. The MZTC was covered with the array ordered, smooth and optimum elongated nanotubes with 5.1 μm of the length, 120.3 nm of the inner diameter 14.5 nm of the wall thickness with pure titanium and crystalline titania as determined by FESEM/EDS, and XRD. The kinetic study by following Langmuir-Hinshelwood(L-H) model and pseudo first order, the significant constant rate was obtained at pH 11 which was 0.079 ppm/min, 0.75 cm² of MZTC catalyst loading size achieved 0.076 ppm/min and 5 ppm of TCC initial concentration reached 0.162 ppm/min. The high-performance liquid chromatography (HPLC) analysis for mechanism study of TCC photocatalytic degradation revealed eleven intermediate products after the whole process of photocatalysis. In regard of toxicology assessment by the bacteria which is Photobacterium phosphoreum, the obtained concentration of TCC at minute 60 was less satisfied with remained 0.36 ppm of TCC was detected indicates that the concentration was above allowable level. Where the allowable level of TCC in stream is 0.1 ppm.

In situ recombination for durable photoelectrocatalytic degradation of organic dye in wastewater

Photoelectrocatalysis (PEC) can effectively degrade organic pollutants by using photoelectrodes without secondary pollution. However, significant mass transport resistance and decreased catalytic activity caused by the shedding of active components remain a barrier to achieving the photocatalytic system with a high degradation rate and long-term durability. Here, an in situ recombination concept is presented to overcome this challenge. The bionic coral-like electrode, obtained by in situ assembly of UIO-66 around TiO₂ nanoflowers (TNF) on Ti-foam substrate, is employed as the photoanode in PEC. Ex situ evaluation of photoelectrochemical activity demonstrates that the UIO-66@TNF/Ti-foam (U@T/T) design significantly improves the light-propagation, light-absorption and charge transfer. In Situ degradation evaluations also shows that the interesting design promotes rapid and stable degradation of organic dye (e.g. Rhodamine B (RhB)). At 2.0 V of bias potential and pH 7.0 in 5 mg L^-1 RhB, under the action of active species such as ·O₂^- and ·OH (proved by the degradation mechanism experiments), the removal rate of RhB can reach 96.1% at 120 min and almost complete removal at 200 min (99.1%).

Adsorption and transformation of tetracyclines on alpha alumina particles with surface modification by anionic surfactant

The adsorption and transformation of tetracyclines (TCs) antibiotics, including oxytetracycline (OTC), chlortetracycline (CTC), and tetracycline (TC), on the sodium dodecyl sulfate (SDS) surfactant-modified α-Al₂O₃ particles were comprehensively investigated in this study. The TCs adsorption was significantly enhanced by using the modified adsorbents compared with the use of the unmodified adsorbents. The experimental conditions were systematically optimized and found to be pH 4, NaCl 1 mM, the contact time of 180 min, and the adsorbent dosage of 25 mg. mL^-1. The high maximum adsorption capacities were approximately 320, 85, and 91 mg. g^-1 for TC, OTC, and CTC, respectively. Meanwhile, the great removal efficiencies of the three antibiotics TC, OTC, and CTC were correspondingly 91.85, 88.4, and 98.3%. The TCs adsorption isotherm and kinetics on the SDS-modified α-Al₂O₃ particles mainly governed by the electrostatic and hydrophobic interactions were clarified by a suitable two-step model, the Fourier transform infrared spectroscopy (FT-IR) and zeta potential measurements. Meanwhile, the TCs structural transformation determined by the liquid chromatography with tandem mass spectrometry (LC-MS/MS) measurement was promoted through the adsorption on the α-Al₂O₃ surface. The TCs transformation rates strongly affected by the TCs adsorption were in the order of CTC > TC > OTC. The found results are promised that the SDS-modified α-Al₂O₃ particles might behave as high-performance adsorbents to remove the TCs from aqueous solutions.

Degradation of Methylparaben Using Optimal WO3 Nanostructures: Influence of the Annealing Conditions and Complexing Agent

In this work, WO₃ nanostructures were synthesized with different complexing agents (0.05 M H₂O₂ and 0.1 M citric acid) and annealing conditions (400 °C, 500 °C and 600 °C) to obtain optimal WO₃ nanostructures to use them as a photoanode in the photoelectrochemical (PEC) degradation of an endocrine disruptor chemical. These nanostructures were studied morphologically by a field emission scanning electron microscope. X-ray photoelectron spectroscopy was performed to provide information of the electronic states of the nanostructures. The crystallinity of the samples was observed by a confocal Raman laser microscope and X-ray diffraction. Furthermore, photoelectrochemical measurements (photostability, photoelectrochemical impedance spectroscopy, Mott-Schottky and water-splitting test) were also performed using a solar simulator with AM 1.5 conditions at 100 mW·cm^-2. Once the optimal nanostructure was obtained (citric acid 0.01 M at an annealing temperature of 600 °C), the PEC degradation of methylparaben (C_O 10 ppm) was carried out. It was followed by ultra-high-performance liquid chromatography and mass spectrometry, which allowed to obtain the concentration of the contaminant during degradation and the identification of degradation intermediates. The optimized nanostructure was proved to be an efficient photocatalyst since the degradation of methylparaben was performed in less than 4 h and the kinetic coefficient of degradation was 0.02 min^-1.

V-Porphyrins Encapsulated or Supported on Siliceous Materials: Synthesis, Characterization, and Photoelectrochemical Properties

Metalloporphyrin-containing mesoporous materials, named VTPP@SBA, were prepared via a simple anchoring of vanadyl porphyrin (5,10,15,20-Tetraphenyl-21H,23H-porphine vanadium(IV) oxide) through a SBA-15-type mesoporous material. For comparison, vanadyl porphyrin was also impregnated on SiO₂ (VTPP/SiO₂). The characterization results of catalysts by XRD, FTIR, DR-UV-vis, and EPR confirm the incorporation of vanadyl porphyrin within the mesoporous SBA-15. These catalysts have also been studied using electrochemical and photoelectrochemical methods. Impedance measurements confirmed that supporting the porphyrin in silica improved the electrical conductivity of samples. In fact, when using mesoporous silica, current densities associated with oxidation/reduction processes appreciably increased, implying an enhancement in charge transfer processes and, therefore, in electrochemical performance. All samples presented n-type semiconductivity and provided an interesting photoelectrocatalytic response upon illumination, especially silica-supported porphyrins. This is the first time that V-porphyrin-derived materials have been tested for photoelectrochemical applications, showing good potential for this use.

Peroxymonosulfate enhanced photoelectrocatalytic oxidation of organic contaminants and simultaneously cathodic recycling of silver

Degradation of organic contaminants with simultaneous recycling of Ag⁺ from silver-containing organic wastewater such as photographic effluents is desired. Although photoelectrocatalysis (PEC) technology is a good candidate for this type of wastewater, its reaction kinetics still needs to be improved. Herein, peroxymonosulfate (PMS) was employed to enhance the PEC kinetics for oxidation of phenol (PhOH) at the anode and reduction of Ag⁺ at the cathode. The degradation efficiency of phenol (PhOH, 0.1 mmol/L) was increased from 42.8% to 96.9% by adding 5 mmol/L PMS at a potential of 0.25 V. Meanwhile, the Ag (by wt%) deposited on the cathode was 28.1% (Ag₂O) in PEC process, while that of Ag (by wt%) was 69.7% (Ag⁰) by adding PMS. According to the electrochemistry analysis, PMS, as photoelectrons acceptor, enhances the separation efficiency of charges and the direct h⁺ oxidation of PhOH at the photoanode. Meantime, the increasing cathode potential avoided H₂ evolution and strongly alkaline at the surface of cathode, thus enabling the deposition of Ag⁺ in the form of metallic silver with the help of PMS. In addition, PMS combined with PEC process was effective in treating photographic effluents.

Photo-electrochemical oxidation herbicides removal in stormwater: Degradation mechanism and pathway investigation

Although advanced oxidation processes (AOPs) such as photoelectrochemical oxidation (PECO), electrochemical oxidation (ECO) and photocatalytic oxidation (PCO), have shown potential for wastewater treatment, their application in urban stormwater has rarely been studied. This paper explored their major degradation mechanisms and possible degradation pathways of herbicides for stormwater applications (with treatment difficulty compared with wastewater). PECO and ECO showed excellent removal performance for diuron (100 %) and moderate for atrazine (around 35 %) under a relatively low potential (2 V). Superoxide radical (·O₂^-) has been found to be the dominant reactive species. Besides, there is evidence to indicate that hydroxyl radical (·OH) and free chlorine (·Cl) also support the degradation reactions. Up to 11 possible intermediate products have been identified during both diuron and atrazine degradation processes under PECO operation. Based on the proposed possible degradation pathways, the intermediates presented during PECO are species with further oxidation. As evidenced by the undetected species of more oxidized intermediates for ECO and PCO, some further degradation steps are missing, which demonstrate their lower oxidation capacity leading to incomplete decomposition of stormwater herbicides. Thus, PECO has a great potential to be developed into a passive stormwater degradation system due to its strong oxidation potential.

Photocatalytic removal of pharmaceutical water pollutants by TiO2 - Carbon dots nanocomposites: A review

Pharmaceuticals are becoming increasingly more relevant water contaminants, with photocatalysts (such as TiO₂) being a promising approach to remove these compounds from water. However, TiO₂ has poor sunlight-harvesting capacity, low photonic efficiency, and poor adsorption towards organic pollutants. One of the emerging strategies to enhance the photocatalytic performance of TiO₂ is by conjugating it with fluorescent carbon dots. Herein, we performed a critical review of the development of TiO₂ - carbon dots nanocomposites for the photocatalytic removal of pharmaceuticals. We found that carbon dots can improve the photocatalytic efficiency of the resulting nanocomposites, mostly due to increasing the adsorption of organic pollutants and enhancing the absorption in the visible range. However, while this approach shows significant promise, we also identified and discussed several aspects that need to be addressed before this strategy could be more widely used. We hope that this review can guide future studies aiming to the development of enhanced photocatalytic TiO₂ - carbon dots nanocomposites.

Decolorization and Degradation of Methyl Orange Azo Dye in Aqueous Solution by the Electro Fenton Process: Application of Optimization

In a batch reactor, the EF advanced oxidation decolorization of aqueous solutions of methyl orange MO, a commercial azo reactive textile dye, was investigated in the presence of two different electrodes. The evaluation included various operational variables such as the IC current intensity (60 mA, 80 mA, and 100 mA), initial concentration of pollutant MO (20 mg/L, 40 mg/L, and 60 mg/L), initial pH of solution (3, 5, and 7), temperature of solution (20 °C, 30 °C, and 50 °C), and initial concentration of catalyst [Fe2+] (0.1 mM, 0.2 mM, and 0.3 mM) on the discoloration rate. A Box-Behnken Design of Experiment (BBD) was used to optimize the parameters that directly affect the Electro-Fenton (EF) process. Under the optimal experimental conditions such as [Fe2+] = 0.232 mM, pH = 3, IC = 80 mA, [MO] = 60 mg/L, and T = 30 ± 0.1 °C, the maximum discoloration rate achieved was 94.9%. The discoloration of the aqueous MO solution during the treatment time was confirmed by analysis of the UV-visible spectrum. After a review of the literature on organic pollutant degradation, the EF system provided here is shown to be one of the best in terms of discoloration rate when compared to other AOPs.

Wastewater Treatment in Mineral Processing of Non-Ferrous Metal Resources: A Review

Water used by mining enterprises needs to be comprehensively recovered and utilized to achieve clean production. This requires the effective treatment of mineral processing wastewater. Wastewater produced during non-ferrous metal mineral processing contains a complex mixture of pollutants at high concentrations, making comprehensive treatment difficult. Here, the sources of and hazards posed by wastewater produced during non-ferrous metal mineral processing are introduced and the techniques for removing heavy metal ions and organic chemicals are reviewed. Chemical precipitation and adsorption methods are often used to remove heavy metal ions. Chemical precipitation methods can be divided into hydroxide and sulfide precipitation methods. Organic chemicals are mainly removed using oxidation methods, including electrochemical oxidation, photocatalytic oxidation, and ultrasonic synergistic oxidation. External and internal cyclic utilization methods for treating wastewater produced by mineral processing plants are introduced, and a feasibility analysis is performed.

Efficient photoelectrocatalytic degradation of azo-dyes over polypyrrole/titanium oxide/reduced graphene oxide electrodes under visible light: Performance evaluation and mechanism insights

Herein, polypyrrole/titanium oxide/reduced graphene oxide (PTi/r-GO) electrodes were prepared and successfully applied for the photoelectrocatalytic (PEC) degradation of methyl orange (MO) under visible light. Polypyrrole-TiO₂ composites rich in p-n heterojunctions were first prepared, then modified with r-GO to improve the electrical conductivity and facilitate charge separation under visible light irradiation. The obtained PTi/r-GO composites were then deposited onto a titanium mesh, which served as the working electrode in PEC experiments. A MO removal efficiency of 93% was achieved in 50 min using PTi/r-GO electrode under PEC conditions (Xe lamp, λ > 420 nm, bias of 0.6 V, 0.1 M Na₂SO₄ electrolyte), which was far higher than MO removal efficiencies under electrocatalytic oxidation (22%) or photocatalytic oxidation (47%) conditions. This confirmed that excellent activity of the PTi/r-GO electrode under PEC conditions was due to a combination of electrochemical and photocatalytic oxidation processes (involving •OH and •O₂^- generation). Further, PTi/r-GO was very stable under the applied PEC conditions, with the MO removal efficiency remaining >90% after five cycles. PEC degradation pathways for MO on PTi/r-GO were explored, with a number of key intermediates in the MO mineralization process identified. Results demonstrate that PEC electrodes combining p-type polypyrrole, n-type TiO₂ and rGO are very effective in the treatment of hazardous organic compounds in wastewater.

Test study and molecular dynamics simulation of Fe3+ modified TiO2 absorbing automobile exhaust

With the growth of the economy, the number of automobiles on the road is fast growing, resulting in substantial environmental pollution from exhaust gas emissions. In the automobile factory, some improvements have been achieved by constructing devices to degrade automobile exhaust. However, although most of the vehicle exhaust emissions have met the national standards, the exhaust gas is superimposed at the same time period due to the increasing traffic volume, making the exhaust emissions seriously reduce the air quality. Therefore, the scholars in the road field began to study new road materials to degrade vehicle exhaust, which has gradually become one of the effective ways to reduce automobile exhaust. Photocatalyst materials have been widely concerned because of their ability to oxidize harmful gases by solar photocatalysis. Yet, the effect has been not satisfactory because of the small light response range of photocatalyst material, which restricts the catalytic effect. In this study, this paper attempts to use Fe3+ to modify the TiO2, which is one of the main photocatalytic materials, to expand the range of light reaction band and to improve the degradation effect of automobile exhaust. The degradation effects of ordinary TiO2 and modified TiO2 on automobile exhaust were compared by test system in the laboratory. The results show that the modified TiO2 can effectively improve the performance of vehicle exhaust degradation. Moreover, the molecular dynamics method was used to establish the channel model of TiO2, and the dynamic process of automobile exhaust diffusion and absorption was simulated. The diffusion law and adsorption process of different types of automobile exhaust gas such as NO, CO, and CO2 in the TiO2 channel were analyzed from the molecular scale through the radial concentration distribution and adsorption energy.

Ti/TiO2 nanotubes sensitized PbS quantum dots as photoelectrodes applied for decomposition of anticancer drugs under simulated solar energy

One of the challenges in research into photoelectrocatalytic (PEC) degradation of pollutants is finding the appropriate photoanode material, which has a significant impact on the process efficiency. Among all others, photoelectrodes based on an ordered TiO₂ nanotube arrays are a promising material due to well-developed surface area and efficient charge separation. To increase the PEC activity of this material, the SILAR method was used to decorate Ti/TiO₂ nanotubes by PbS quantum dots (QD). The ifosfamide (IF) degradation rate constants was twice as higher for PbS-Ti/TiO₂ (0.0148 min^-1) than for Ti/TiO₂ (0.0072 min^-1). Our research showed the highest efficiency of PEC degradation of drugs using IIIPbS-Ti/TiO₂ made with 3 SILAR cycles (PbS QD size mainly 2-4 nm). The 4 and 6 of SILAR cycles resulted in the aggregation of PbS nanoparticles on the Ti/TiO₂ surface and decreased IF PEC degradation rate to 0.0043 and 0.0033 min^-1, respectively. Research on PEC mechanism has shown that the drugs are degraded mainly by the activity of photogenerated holes and hydroxyl radicals. In addition, the identified drug intermediates made possible to propose a degradation pathways of anticancer drugs and the ecotoxicity test show no inhibition of Lemna minor growth of treated solutions.

The application of photoelectrocatalysis in the degradation of rhodamine B in aqueous solutions: a review

The pollution of the water environment by industrial effluents is an ongoing challenge due to the rate of industrialisation and globalisation. Photoelectrocatalysis (PEC), an electrochemical advanced oxidation process, has proven to be an effective method for removing organics from wastewater. Photoelectrocatalysis is environmentally benign, cost-effective and easy to operate. In this present review, we examine the recent progress in the removal of rhodamine B dye, a common constituent of textile effluent released into the environment, through photoelectrocatalytic degradation. We present a detailed discussion on the use of different kinds of unmodified and modified photoanodes that have been explored for the photoelectrocatalytic removal of this dye. More importantly, discussions are presented on the mechanisms and kinetics of the degradation of rhodamine B dye using these photoanodes. Hence, this review will be beneficial for researchers in developing future projects in the area of wastewater treatments through photoelectrocatalysis.

The pollution of the water environment by industrial effluents is an ongoing challenge due to the rate of industrialisation and globalisation.

Photoelectrocatalysis on TiO2 meshes: different applications in the integrated urban water management

Recently, among AOPs, photoelectrocatalysis (PEC) on TiO2 is gaining interest. In this study, five different real waters sampled in four different points of the integrated urban water management (IUWM) system were tested with PEC and UV alone, for comparison. This work aims to verify the effect of the PEC suggesting the optimal position in IUWM system where the PEC should be located to obtain the best performance. In groundwaters (GWs), PEC effectively removed atrazine-based compounds (> 99%), trichloroethylene, and perchloroethylene (96%), after 15 min of reaction time. However, given the low concentrations of emerging compounds, the synergistic effect of UV radiation with the catalyst and with the polarization of the mesh was not visible, with very few differences compared with the results obtained with UV alone. Pharmaceutical industrial wastewater (IWW) showed a significant increase in biodegradability after 2 h, both if subjected to PEC or UV (200%), despite the absence of COD removal. The PEC applied on IWW from a sewage sludge treatment plant allowed to effectively remove the COD (39.6%) and increase the biodegradability (300%). Good results in terms of COD removal (33.9%) and biodegradability increase (+900%) were also achieved testing PEC on wastewater treatment plant effluent. Except for GWs, PEC allowed significant EEO savings respect to UV alone (76.2-99.1%).

Fundamentals and applications of photoelectrocatalysis as an efficient process to remove pollutants from water: A review

Water pollution is an environmental problem in constant raising because of population growing, industrial development, agricultural frontier expansion, and principally because of the lack of wastewater treatment technology to remove organic recalcitrant and toxic pollutants from industrial and domestic wastewater. Recalcitrant compounds are a serious environmental and health problem mainly due to their toxicity and potential hazardous effects on living organisms, including human beings. Conventional wastewater treatments have not been able to remove efficiently pollutants from water; however, electrochemical advanced oxidation processes (EAOPs) are able to solve this environmental concern. One of the most recent EAOPs technology is photoelectrocatalysis (PEC), it consists in applying an external bias potential to a semiconductor film placed over a conductive substrate to avoid the recombination of photogenerated electron-hole (e^-/h⁺) pairs, increasing h⁺ availability and hydroxyl radicals' formation, responsible for promoting the degradation/mineralization of organic pollutants in aqueous medium. This review summarizes the recent advances in PEC as a promising technology for wastewater treatment. It addresses the fundamentals and kinetic aspects of PEC. An analysis of photoanode materials and of the configuration of photoelectrochemical reactors is also presented, including an analysis of the influence of the main operational parameters on the treatment of contaminated water. Finally, the most recent applications of PEC are reviewed, and the challenges and perspectives of PEC in wastewater treatment are discussed.

Application of polyoxometalates in photocatalytic degradation of organic pollutants

Organic pollutants are highly toxic, accumulative, and difficult to degrade or eliminate. As a low-cost, high-efficiency and energy-saving environmental purification technology, photocatalytic technology has shown great advantages in solving increasingly serious environmental pollution problems. The development of efficient and durable photocatalysts for the degradation of organic pollutants is the key to the extensive application of photocatalysis technology. Polyoxometalates (POMs) are a kind of discrete metal-oxide clusters with unique photo/electric properties which have shown promising applications in photocatalytic degradation. This review summarizes the recent advances in the design and synthesis of POM-based photocatalysts, as well as their application in the degradation of organic dyes, pesticides and other pollutants. In-depth perspective views are also proposed in this review.

TiO2@Cu2O n-n Type Heterostructures for Photochemistry

A TiO2@Cu2O semiconductor heterostructure with better photochemical response compared to TiO2 was obtained using an electrochemical deposition method of Cu2O on the surface of TiO2 nanotubes. The choice of 1D nanotubes was motivated by the possibility of achieving fast charge transfer, which is considered best suited for photochemical applications. The morphology and structural properties of the obtained heterojunction were determined using standard methods -SEM and Raman spectroscopy. Analysis of photoelectrochemical properties showed that TiO2@Cu2O heterostructures exhibit better properties resulting from an interaction with sunlight than TiO2. A close relationship between the morphology of the heterostructures and their photoproperties was also demonstrated. Investigations representing a combination of photoelectrochemical cells for hydrogen production and photocatalysis-photoelectrocatalysis-were also carried out and confirmed the observations on the photoproperties of heterostructures. Analysis of the Mott-Schottky plots as well as photoelectrochemical measurements (Iph-V, Iph-t) showed that TiO2 as well as, unusually, Cu2O exhibit n-type conductivity. On this basis, a new energy diagram of the TiO2@Cu2O system was proposed. It was found that TiO2@Cu2O n-n type heterostructure prevents the processes of photocorrosion of copper(I) oxide contained in a TiO2-based heterostructure.

Simultaneous removal of organic pollutants and heavy metals in wastewater by photoelectrocatalysis: A review

As a powerful technique by combining photocatalysis with electrochemistry, photoelectrocatalysis has been extensively explored to simultaneously remove mixed pollutants of organic and heavy metal in wastewater in the past decade. In the photoelectrocatalytic system, the bias potential can remarkably promote the oxidation of organic pollutants on the photoanode by suppressing the recombination of photogenerated electron-hole pairs and extending the lifetime of photogenerated holes. Meanwhile, some photogenerated electrons are driven by the bias potential to the cathode to reduce heavy metals. In this review, we summarize the research advances in photoelectrocatalytic treatment of organic-heavy metal mixed pollution systems under UV light, visible light and sunlight. We demonstrate the main operation variables affecting the photoelectrocatalytic removal processes of organic pollutants and heavy metals. The problems for utilization of solar energy in photoelectrocatalysis are discussed. Finally, this review proposes the perspectives for future development of photoelectrocatalysis to industrial applications.

Promotion of TiO2 Nanotube-Confined Pt Nanoparticles via Surface Modification with Fe2O3 for Ethylene Oxidation at Low Temperature

A modified confined catalyst with Pt nanoparticles on the interior and Fe₂O₃ on the exterior surface of TiO₂ nanotubes (Pt-in/Fe₂O₃-TNTs) was prepared and investigated for catalyzing the oxidation of ethylene. Compared with the Pt-in/TNTs without Fe₂O₃ modification, the Pt-in/Fe₂O₃-TNTs exhibited a significantly enhanced activity, and the complete conversion temperature of ethylene decreased from 170 to 95 °C. X-ray photoelectron spectroscopy analysis indicated that the Pt nanoparticles were stabilized at higher oxidation states in the Pt-in/Fe₂O₃-TNT catalyst. It was proposed that the modification of Fe₂O₃ on the outer surface can tune the electronic state of the encapsulated Pt particles and accelerate the electrons transferred from Pt to Fe species via TiO₂ nanotubes, thus improving the catalytic oxidation performance of the confined catalyst.

Perovskite Oxide-Based Materials for Photocatalytic and Photoelectrocatalytic Treatment of Water

Meeting the global challenge of water availability necessitates diversification from traditional water treatment methods to other complementary methods, such as photocatalysis and photoelectrocatalysis (PEC), for a more robust solution. Materials play very important roles in the development of these newer methods. Thus, the quest and applications of a myriad of materials are ongoing areas of water research. Perovskite and perovskite-related materials, which have been largely explored in the energy sectors, are potential materials in water treatment technologies. In this review, attention is paid to the recent progress in the application of perovskite materials in photocatalytic and photoelectrocatalytic degradation of organic pollutants in water. Water treatment applications of lanthanum, ferrite, titanate, and tantalum (and others)-based perovskites are discussed. The chemical nature and different synthetic routes of perovskites or perovskite composites are presented as fundamental to applications.

Photoelectrocatalytic degradation of p-chloronitrobenzene by g-C3N4/TiO2 nanotube arrays photoelectrodes under visible light irradiation

As a typical refractory pollutant, p-chloronitrobenzene (p-CNB) from industrial wastewater poses a serious threat to the aquatic environment safety and human health. The photoelectrocatalytic (PEC) technology is regarded as a promising and cleaner approach for p-CNB removal. Therefore, the graphitic carbon nitride (g-C₃N₄) modified TiO₂ nanotube arrays (g-C₃N₄/TNAs) were prepared as the photoelectrodes for p-CNB degradation. The PEC degradation efficiency for p-CNB by g-C₃N₄/TNAs (0.00484 min^-1) was much higher than that by bare TNAs (0.00135 min^-1) under visible light. The g-C₃N₄/TNAs photoelectrodes exhibited excellent visible-light response, efficient charges separation and high redox potentials of electron/hole, which was favorable for p-CNB degradation. The radical scavenging experiments indicated that both reductive electrons and oxidized species (holes and ·OH) played crucial roles simultaneously during the dechlorination process, whereas the mineralization of p-CNB mainly depended on the photo-generated holes and ·OH. The degradation pathways of p-CNB were proposed through GC/MS spectra. The acute toxicity, bioaccumulation factor and mutagenicity of identified intermediates were reduced after PEC degradation by g-C₃N₄/TNAs photoelectrodes. The Z-scheme g-C₃N₄/TNAs provided an efficient approach for simultaneous dechlorination and mineralization of refractory pollutants.

Influence of ruthenium doping on UV- and visible-light photoelectrocatalytic color removal from dye solutions using a TiO2 nanotube array photoanode

The photocatalytic activity of TiO₂ anodes was enhanced by synthesizing Ru-doped Ti|TiO₂ nanotube arrays. Such photoanodes were fabricated via Ti anodization followed by Ru impregnation and annealing. The X-ray diffractograms revealed that anatase was the main TiO₂ phase, while rutile was slightly present in all samples. Scanning electron microscopy evidenced a uniform morphology in all samples, with nanotube diameter ranging from 60 to 120 nm. The bias potential for the photoelectrochemical (PEC) treatment was selected from the electrochemical characterization of each electrode, made via linear sweep voltammetry. All the Ru-doped TiO₂ nanotube array photoanodes showed a peak photocurrent (PP) and a saturation photocurrent (SP) upon their illumination with UV or visible light. In contrast, the undoped TiO₂ nanotubes only showed the SP, which was higher than that reached with the Ru-doped photoanodes using UV light. An exception was the Ru(0.15 wt%)-doped TiO₂, whose SP was comparable under visible light. Using that anode, the activity enhancement during the PEC treatment of a Terasil Blue dye solution at E_bias(PP) was much higher than that attained at E_bias(SP). The percentage of color removal at 120 min with the Ru(0.15 wt%)-doped TiO₂ was 98% and 55% in PEC with UV and visible light, respectively, being much greater than 82% and 28% achieved in photocatalysis. The moderate visible-light photoactivity of the Ru-doped TiO₂ nanotube arrays suggests their convenience to work under solar PEC conditions, aiming at using a large portion of the solar spectrum.

Disinfection of Wastewater by UV-Based Treatment for Reuse in a Circular Economy Perspective. Where Are We at?

Among the critical issues that prevent the reuse of wastewater treatment plants (WWTPs) effluents in a circular economy perspective, the microbiological component plays a key role causing infections and diseases. To date, the use of conventional chemical oxidants (e.g., chlorine) represent the main applied process for wastewater (WW) disinfection following a series of operational advantages. However, toxicity linked to the production of highly dangerous disinfection by-products (DBPs) has been widely demonstrated. Therefore, in recent years, there is an increasing attention to implement sustainable processes, which can simultaneously guarantee the microbiological quality of the WWs treated and the protection of both humans and the environment. This review focuses on treatments based on ultraviolet radiation (UV) alone or in combination with other processes (sonophotolysis, photocatalysis and photoelectrocatalysis with both natural and artificial light) without the dosage of chemical oxidants. The strengths of these technologies and the most significant critical issues are reported. To date, the use of synthetic waters in laboratory tests despite real waters, the capital and operative costs and the limited, or absent, experience of full-scale plant management (especially for UV-based combined processes) represent the main limits to their application on a larger scale. Although further in-depth studies are required to ensure full applicability of UV-based combined processes in WWTPs for reuse of their purified effluents, excellent prospects are presented thanks to an absent environmental impact in terms of DBPs formation and excellent disinfection yields of microorganisms (in most cases higher than 3-log reduction).

Occurrence, statutory guideline values and removal of contaminants of emerging concern by Electrochemical Advanced Oxidation Processes: A review

A wide variety of chemical compounds are used in human activities; however, part of these compounds reach surface water, groundwater and even water considered for potable uses. Due to the limited efficiency of water treatment by the Water and Wastewater Treatment Plants, the presence of these compounds in natural and human consumption waters can be very harmful due to their high persistence and adverse effects; these characteristics define the contaminants of emerging concern (CECs). Water treatment by Electrochemical Advanced Oxidation Processes (EAOPs) has been evaluated as a promising process for the removal of persistent and recalcitrant organic contaminants. With this background, the present review aims to gather studies and information published between 2015 and 2020 regarding the occurrence of CECs in surface, potable and groundwater, its treatment by EAOPs, the main operating conditions and by-product generation of EAOPs, contaminant toxicity assessments and international statutory guideline values concerning CEC standards and allowable concentrations in the environment and treated drinking water. Therefore, in this review it was found that the compounds bisphenol A (BPA), diethyltoluamide (DEET), 17α-ethinyl estradiol (EE2), perfluorobutanoic acid (PFBA), carbamazepine, caffeine and atrazine were the most frequently detected in water sources, with concentrations ranging from 35.54-4800, 1.21-98, 0.005-38.5, 5-742.904, 0.0071-586, 0.89-1040, and 100-323 (ng L-1), respectively. Among the operational conditions of EAOPs, current density, pH and oxidant concentration are the main operational parameters that have an influence on these treatment technologies, besides the by-products generated, which might be removed by the integration of EAOPs with biological digestion treatments. Regarding the values of water quality standards, many CECs do not have established standard allowable concentration values, which represents a concern toward the possible toxic effects of these compounds on non-target organisms.

Technologies Employed in the Treatment of Water Contaminated with Glyphosate: A Review

Glyphosate [N-(phosphonomethyl)-glycine] is a herbicide with several commercial formulations that are used generally in agriculture for the control of various weeds. It is the most used pesticide in the world and comprises multiple constituents (coadjutants, salts, and others) that help to effectively reach the action's mechanism in plants. Due to its extensive and inadequate use, this herbicide has been frequently detected in water, principally in surface and groundwater nearest to agricultural areas. Its presence in the aquatic environment poses chronic and remote hazards to human health and the environment. Therefore, it becomes necessary to develop treatment processes to remediate aquatic environments polluted with glyphosate, its metabolites, and/or coadjutants. This review is focused on conventional and non-conventional water treatment processes developed for water polluted with glyphosate herbicide; it describes the fundamental mechanism of water treatment processes and their applications are summarized. It addressed biological processes (bacterial and fungi degradation), physicochemical processes (adsorption, membrane filtration), advanced oxidation processes-AOPs (photocatalysis, electrochemical oxidation, photo-electrocatalysis, among others) and combined water treatment processes. Finally, the main operating parameters and the effectiveness of treatment processes are analyzed, ending with an analysis of the challenges in this field of research.

Liquid-Phase Exfoliated GeSe Nanoflakes for Photoelectrochemical-Type Photodetectors and Photoelectrochemical Water Splitting

Photoelectrochemical (PEC) systems represent powerful tools to convert electromagnetic radiation into chemical fuels and electricity. In this context, two-dimensional (2D) materials are attracting enormous interest as potential advanced photo(electro)catalysts and, recently, 2D group-IVA metal monochalcogenides have been theoretically predicted to be water splitting photocatalysts. In this work, we use density functional theory calculations to theoretically investigate the photocatalytic activity of single-/few-layer GeSe nanoflakes for both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) in pH conditions ranging from 0 to 14. Our simulations show that GeSe nanoflakes with different thickness can be mixed in the form of nanoporous films to act as nanoscale tandem systems, in which the flakes, depending on their thickness, can operate as HER- and/or OER photocatalysts. On the basis of theoretical predictions, we report the first experimental characterization of the photo(electro)catalytic activity of single-/few-layer GeSe flakes in different aqueous media, ranging from acidic to alkaline solutions: 0.5 M H2SO4 (pH 0.3), 1 M KCl (pH 6.5), and 1 M KOH (pH 14). The films of the GeSe nanoflakes are fabricated by spray coating GeSe nanoflakes dispersion in 2-propanol obtained through liquid-phase exfoliation of synthesized orthorhombic (Pnma) GeSe bulk crystals. The PEC properties of the GeSe nanoflakes are used to design PEC-type photodetectors, reaching a responsivity of up to 0.32 AW-1 (external quantum efficiency of 86.3%) under 455 nm excitation wavelength in acidic electrolyte. The obtained performances are superior to those of several self-powered and low-voltage solution-processed photodetectors, approaching that of self-powered commercial UV-Vis photodetectors. The obtained results inspire the use of 2D GeSe in proof-of-concept water photoelectrolysis cells.

Design of Experiment for the Optimization of Pesticide Removal from Wastewater by Photo-Electrochemical Oxidation with TiO2 Nanotubes

The Design of Experiment (DoE) technique has been used to investigate the photo-electrochemical removal of diuron (DRN) from wastewater. The process is carried out in a photo-electrochemical flow reactor, in which titania nanotubular electrode is irradiated with a simulated solar light. Different operative conditions have been investigated, in a planned 23 full factorial design in which imposed current density, flow rate and initial concentration have been varied at two levels. The removal process of DRN was investigated in terms of specific removal rate (K) and cell voltage (E), which were assumed as objective functions: the results show that the applied current has a paramount effect on both of the objective functions. From the analyses of the intermediates, it appears that the investigated parameters may exert different effects on the distribution of the reaction products: the initial concentration of diuron and the electrode potential seem to play a more important role, in this case.

Photoelectrocatalyzed degradation of organophosphorus pesticide fenamiphos using WO3 nanorods as photoanode

In this study, WO₃ nanostructures were synthesized by the electrochemical anodization technique to use them on the degradation of persistent organic compounds such as the pesticide fenamiphos. The acids electrolyte used during the anodization were two different: 1.5 M H₂SO₄ - 0.05 M H₂O₂ and 1.5 M CH₄O₃S - 0.05 M H₂O₂. Once the samples have been manufactured, they have been subjected to different tests to analyze the properties of the nanostructures. With Field Emission Scanning Electron Microscopy (FE-SEM) the samples have been examined morphologically, their composition and crystallinity has been studied through Raman Spectroscopy and their photoelectrochemical behaviour by Photoelectrochemical Impedance Spectroscopy (PEIS). Finally, degradation tests have been carried out using the technique known as photoelectrocatalysis (PEC). The conditions that were applied in this technique were a potential of 1 V_Ag/AgCl and simulated solar illumination. The degradation process was monitored by UV-Visible and High-Performance liquid Chromatography (HPLC) to control the course of the experiment. The nanostructures obtained with 1.5 M CH₄O₃S - 0.05 M H₂O₂ electrolyte showed a better photoelectrochemical behaviour than nanostructures synthesized with 1.5 M H₂SO₄ - 0.05 M H₂O₂. The fenamiphos degradation was achieved at 2 h of experiment and the intermediate formation was noticed at 1 h of PEC experiment.

Semiconductor Electrode Materials Applied in Photoelectrocatalytic Wastewater Treatment—an Overview

Industrial sources of environmental pollution generate huge amounts of industrial wastewater containing various recalcitrant organic and inorganic pollutants that are hazardous to the environment. On the other hand, industrial wastewater can be regarded as a prospective source of fresh water, energy, and valuable raw materials. Conventional sewage treatment systems are often not efficient enough for the complete degradation of pollutants and they are characterized by high energy consumption. Moreover, the chemical energy that is stored in the wastewater is wasted. A solution to these problems is an application of photoelectrocatalytic treatment methods, especially when they are coupled with energy generation. The paper presents a general overview of the semiconductor materials applied as photoelectrodes in the treatment of various pollutants. The fundamentals of photoelectrocatalytic reactions and the mechanism of pollutants treatment as well as parameters affecting the treatment process are presented. Examples of different semiconductor photoelectrodes that are applied in treatment processes are described in order to present the strengths and weaknesses of the photoelectrocatalytic treatment of industrial wastewater. This overview is an addition to the existing knowledge with a particular focus on the main experimental conditions employed in the photoelectrocatalytic degradation of various pollutants with the application of semiconductor photoelectrodes.

Structural-Phase Catalytic Redox Reactions in Energy and Environmental Applications

The structure-property engineering of phase-based materials for redox-reactive energy conversion and environmental decontamination nanosystems, which are crucial for achieving feasible and sustainable energy and environment treatment technology, is discussed. An exhaustive overview of redox reaction processes, including electrocatalysis, photocatalysis, and photoelectrocatalysis, is given. Through examples of applications of these redox reactions, how structural phase engineering (SPE) strategies can influence the catalytic activity, selectivity, and stability is constructively reviewed and discussed. As observed, to date, much progress has been made in SPE to improve catalytic redox reactions. However, a number of highly intriguing, unresolved issues remain to be discussed, including solar photon-to-exciton conversion efficiency, exciton dissociation into active reductive/oxidative electrons/holes, dual- and multiphase junctions, selective adsorption/desorption, performance stability, sustainability, etc. To conclude, key challenges and prospects with SPE-assisted redox reaction systems are highlighted, where further development for the advanced engineering of phase-based materials will accelerate the sustainable (active, reliable, and scalable) production of valuable chemicals and energy, as well as facilitate environmental treatment.