Adsorption of organic pollutants by nanomaterial-based adsorbents: An overview

Enhancing adsorption capacity of carbon nanotubes through sand filters for the removal of organic pollutants: a column investigation

Dissolved organic pollutants caused by paints, detergents, herbicides, and toxins cannot be removed by conventional water treatment processes such as filtration. Different figures of activated carbon such as carbon nanotubes (CNTs) are substances to obliterate these contaminants. Although these CNTs have higher ability to decompose organic contaminants, using the slurry form of CNTs is not suitable due to the removal requirement at the end of the treatment procedure. In this study, upgraded CNTs attached to particles of sand filters (CNTsand) were synthesised and applied to remove dissolved organic pollutants. The results revealed the high capacity of the CNTsand to extract organic contaminants. The column test with natural water compared to the distilled water had a more extended breakpoint, higher adsorption capacity, and consequently, further removal efficiency, such that for the surface area loading rate of 4.8 ml/min, the breakpoint increased from 739 minutes to 936 minutes as well as the volume of passed water grew from 3546 ml to 4493 ml; Therefore, the maximum adsorption capacity was enhanced from 67.3 mg/g to 89.5 mg/g. In conclusion, the adequacy and efficiency of the upgraded nanotube coating on sand grains to remove organic pollutants were confirmed.

Green synthesis of carbon nanotubes functionalized with iron nanoparticles and coffee husk biomass for efficient removal of losartan and diclofenac: Adsorption kinetics and ANN modeling studies

The presence of emerging contaminants in wastewater poses a global environmental challenge, requiring the development of innovative materials or methods for their treatment. This study focused on the production of green functionalized carbon nanotubes (CNTs) and using them in the adsorption of the pharmaceuticals Losartan (LOS) and Diclofenac (DIC). The efficiency of the methodology was verified by characterization techniques. Elemental composition analysis indicated a significant increase in the iron content after the green functionalization, proving the effectiveness of the method. Thermogravimetric analysis showed similar thermal degradation profiles for pristine CNTs and functionalized CNTs, indicating better post-functionalization thermal stability. BET analysis revealed mesoporous characteristics of CNTs, with increased surface area and pore volumes after functionalization. X-Ray diffraction confirmed the preservation of the lattice structure of the CNTs post-functionalization and post-adsorption, with changes in peak broadening suggesting surface modifications. LOS and DIC adsorption were evaluated via kinetic studies at four different concentrations (0.1-0.4 mmol/L) that were best represented by the pseudo-second order model, suggesting chemisorption mechanisms, with faster and higher uptakes for DIC (0.084-0.261 mmol/g; teq = 5 min) when compared to LOS (0.058-0.235 mmol/g; teq = 20 min). The curves were also studied via artificial neural networks (ANN) and revealed that the best ANN architecture for representing the experimental data is a network with [3 5 5 2] neurons trained using the Bayesian-Regularization algorithm and the Log-sigmoid (hidden layers) and Linear (output layer) transfer functions. The desorption study showed that CaCl2 had better performance in CNT regeneration, reaching its removal capacity above 50% up to 3 cycles, for both pharmaceuticals. These findings reveal the potential of the developed material as a promising adsorbent for targeted removal of pollutants, contributing to advances in the remediation of emerging contaminants and the application of artificial intelligence in adsorption research.

Biopolymer-based beads for the adsorptive removal of organic pollutants from wastewater: Current state and future perspectives

Among biopolymer-based adsorbents, composites in the form of beads have shown promising results in terms of high adsorption capacity and ease of separation from the effluents. This review addresses the potential of biopolymer-based beads to remediate wastewaters polluted with emerging organic contaminants, for instance dyes, active pharmaceutical ingredients, pesticides, phenols, oils, polyaromatic hydrocarbons, and polychlorinated biphenyls. High adsorption capacities up to 2541.76 mg g-1 for dyes, 392 mg g-1 for pesticides and phenols, 1890.3 mg g-1 for pharmaceuticals, and 537 g g-1 for oils and organic solvents have been reported. The review also attempted to convey to its readers the significance of wastewater treatment through adsorption by providing an overview on decontamination technologies of organic water contaminants. Various preparation methods of biopolymer-based gel beads and adsorption mechanisms involved in the process of decontamination have been summarized and analyzed. Therefore, we believe there is an urge to discuss the current state of the application of biopolymer-based gel beads for the adsorption of organic pollutants from wastewater and future perspectives in this regard since it is imperative to treat wastewater before releasing into freshwater bodies.

Effects of dissolved organic matter on the environmental behavior and toxicity of metal nanomaterials: A review

Metal nanomaterials (MNMs) have been released into the environment during their usage in various products, and their environmental behaviors directly impact their toxicity. Numerous environmental factors potentially affect the behaviors and toxicity of MNMs with dissolved organic matter (DOM) playing the most essential role. Abundant facts showing contradictory results about the effects of DOM on MNMs, herein the occurrence of DOM on the environmental process change of MNMs such as dissolution, dispersion, aggregation, and surface transformation were summarized. We also reviewed the effects of MNMs on organisms and their mechanisms in the environment such as acute toxicity, oxidative stress, oxidative damage, growth inhibition, photosynthesis, reproductive toxicity, and malformation. The presence of DOM had the potential to reduce or enhance the toxicity of MNMs by altering the reactive oxygen species (ROS) generation, dissolution, stability, and electrostatic repulsion of MNMs. Furthermore, we summarized the factors that affected different toxicity including specific organisms, DOM concentration, DOM types, light conditions, detection time, and production methods of MNMs. However, the more detailed mechanism of interaction between DOM and MNMs needs further investigation.

Recent Advances in Metal-Organic Framework (MOF)-Based Composites for Organic Effluent Remediation

Environmental pollution caused by organic effluents emitted by industry has become a worldwide issue and poses a serious threat to the public and the ecosystem. Metal-organic frameworks (MOFs), comprising metal-containing clusters and organic bridging ligands, are porous and crystalline materials, possessing fascinating shape and size-dependent properties such as high surface area, abundant active sites, well-defined crystal morphologies, and huge potential for surface functionalization. To date, numerous well designated MOFs have emerged as critical functional materials to solve the growing challenges associated with water environmental issues. Here we present the recent progress of MOF-based materials and their applications in the treatment of organic effluents. Firstly, several traditional and emerging synthesis strategies for MOF composites are introduced. Then, the structural and functional regulations of MOF composites are presented and analyzed. Finally, typical applications of MOF-based materials in treating organic effluents, including chemical, pharmaceutical, textile, and agricultural wastewaters are summarized. Overall, this review is anticipated to tailor design and regulation of MOF-based functional materials for boosting the performance of organic effluent remediation.

Enhanced uranium removal from aqueous solution by core-shell Fe0@Fe3O4: Insight into the synergistic effect of Fe0 and Fe3O4

In this study, Fe0@Fe3O4 was synthesized and used to remove U(VI) from groundwater. Different experimental conditions and cycling experiments were used to investigate the performance of Fe0@Fe3O4 in the U(VI) removal, and the XRD, TEM, XPS and XANES techniques were employed to characterize the Fe0@Fe3O4. The results showed that the U(VI) removal efficiency of Fe0@Fe3O4 was 48.5 mg/g that was higher than the sum of removal efficiency of Fe0 and Fe3O4. The uranium on the surface of Fe0@Fe3O4 mainly existed as U(IV), followed by U(VI) and U(V). The Fe0 content decreased after reaction, while the Fe3O4 content increased. Based on the results of experiments and characterization, the enhanced removal efficiency of Fe0@Fe3O4 was attributed to the synergistic effect of Fe0 and Fe3O4 in which Fe3O4 accelerated the Fe0 corrosion that promoted the progressively formation of Fe(II) that promoted the reduction of adsorbed U(VI) to U(IV) and incorporated U(VI) to U(V). The performance of Fe0@Fe3O4 at near-neutrality condition was better than at acidic and alkalic conditions. The chloride ions, sulfate ions and nitrate ions showed minor effect on the Fe0@Fe3O4 performance, while carbonate ions exhibited significant inhibition. The metal cations showed different effect on the Fe0@Fe3O4 performance. The removal efficiency of Fe0@Fe3O4 decreased with the number of cycling experiment. Ionizing radiation could regenerate the used Fe0@Fe3O4. This study provides insight into the U(VI) removal by Fe0@Fe3O4 in aqueous solution.

Lignin-Based Nanospheres as Environmental Remediation Platforms for Anionic Dye Contaminants

Modern manufacturing of textiles, pharmaceuticals, food, cosmetics, plastics, paper, etc. involves the utilization of anionic and cationic dyes that lead to significant water contamination. Recent research has explored the use of nanomaterials toward developing nanoadsorbents for water decontamination caused by industrial pollution. Here, we report on a novel platform for anionic dye remediation, consisting of a polyethylenimine-functionalized lignin nanosphere (PEI-LNS). The designed nanomaterial shows significant ability to adsorb an anionic dye selected as a proof-of-concept-Sulforhodamine B, from aqueous solutions. The PEI lignin nanoadsorbents (PEI-LNS) showed a better ability to adsorb Sulforhodamine B sodium salt (SBSS) when compared to the raw lignin nanosphere adsorbent (LNS), especially in acidic conditions. The nanomaterial was characterized through transmission electron microscopy, scanning electron microscopy, Brunauer-Emmett-Teller surface area analysis, elemental analysis, zeta potential, thermogravimetric analysis, Fourier transform infrared spectroscopy, and nuclear magnetic resonance. The impacts of ionic strength, contact time, pH, and adsorbent concentration have been evaluated. The ability of PEI-LNS to adsorb SBSS was found to be consistent with Langmuir isotherms and pseudo-second-order kinetic models. The PEI-LNS could be recycled three times, reaching a good (85%) adsorbing capacity even in the third cycle. The study demonstrates that PEI-LNS has a strong affinity as a novel adsorbent for anionic dyes and could be employed in environmental cleanups pertaining to such contaminations.

High-efficiency removal of pyrethroids using a redesigned odorant binding protein

Pyrethroids are ubiquitously present in environmental media and threaten both the ecosystem and human health. To explore effective ways to remove pyrethroids from the environment, an odorant binding protein (OBP) with affinity for various pyrethroids was investigated. Initially, the target OBP, Spodoptera littoralis pheromone binding protein 1 (SlitPBP1), underwent redesign to enhance its affinity for pyrethroids. The modified SlitPBP1E97ND106E demonstrated a substantially increased affinity for deltamethrin (DeltaM), with a dissociation constant of 0.77 ± 0.17 μM. The affinity of SlitPBP1E97ND106E for other pyrethroids also increased to varying extents. Consequently, SlitPBP1E97ND106E displayed a markedly enhanced capability to adsorb and remove pyrethroids. When exposed to free SlitPBP1E97ND106E in solution, the reduction in DeltaM surged from 16.78 ± 0.32% to 97.51 ± 0.56%. SlitPBP1E97ND106E was immobilized by coupling the protein to Ni2+-NTA agarose resin. Liquid chromatography results attested to the superior efficacy of immobilized SlitPBP1E97ND106E in removing pyrethroids, especially DeltaM. No significant differences in pyrethroid removal were detected across various water samples. Our findings introduce a potent tool for pyrethroid removal. A wider range of OBPs can similarly be optimized and applied to remove organic pollutants, including but not limited to pesticides.

Precursor-oriented design of nano-alumina for efficient removal of antibiotics

Rapid and efficient removal of environmental antibiotics is vital to curb bacterial resistance. Through rational precursors-oriented design, we attain the best Al2O3 absorbent by 500 °C calcination of ammonium aluminium carbonate hydroxide (AACH) precursor from NH4HCO3 route (AACH-NH4HCO3-500) for fast and efficient removal of tetracycline (TC) and other antibiotics from environmental waters including high-salinity wastewater. AACH-NH4HCO3-500 (0.25 g·L-1) can remove (69.92 ± 1.78)% of aqueous TC (0.025 g·L-1) within 5 min and (97.62 ± 2.75)% within 2 h, and the adsorption capacity is 444.4 mg·g-1, which is the highest qmax of TC for the 2 h-adsorptions among numerous adsorbents. AACH-NH4HCO3-500 has fine tolerance to the coexisting substances, and can be easily regenerated and reused, and has no harm even discarded. The relations among the synthetic methods, the structural features, and the adsorption functions of Al2O3 are disclosed through a systematic comparison of the commercial Al2O3 and different Al2O3 nanomaterials attained from three precursors produced by five different routes. The reasons behind the exceptional adsorption performance are discussed throughout. Our findings would facilitate the development of excellent adsorbents for removal of other pollutants.

Recent advances in metal organic frameworks-based magnetic nanomaterials for waste water treatment

Magnetic nanoparticle-incorporated metal organic frameworks (MOF) are potential composites for various applications such as catalysis, water treatment, drug delivery, gas storage, chemical sensing, and heavy metal ion removal. MOFs exhibits high porosity and flexibility enabling guest species like heavy metal ions to diffuse into bulk structure. Additionally, shape and size of the pores contribute to selectivity of the guest materials. Incorporation of magnetic materials allows easy collection of adsorbent materials from solution system making the process simple and cost-effective. In view of the above advantages in the present review article, we are discussing recent advances of different magnetic material-incorporated MOF (Mg-MOF) composite for application in photocatalytic degradation of dyes and toxic chemicals, adsorption of organic compounds, adsorption of heavy metal ions, and adsorption of dyes. The review initially discusses on properties of Mg-MOF, different synthesis techniques such as mechanochemical, sonochemical (ultrasound) synthesis, slow evaporation and diffusion methods, solvo(hydro)-thermal and iono-thermal method, microwave-assisted method, microemulsion method post-synthetic modification template strategies and followed by application in waste water treatment.

One-step synthesis of magnetic fly ash composites for methylene blue removal: batch and column study

This study focuses on the synthesis of magnetic fly ash composites and its application for the removal of methylene blue (MB) from wastewater. By-product of oil power plants, oil fly ash, was treated with magnetic nanoparticles after chemical surface modification and dubbed modified fly ash (MFA). MFA was characterized by X-ray fluorescence, diffractogram analysis, scanning electron microscopy, energy-dispersive X-ray (EDX), and Fourier transform infrared (FT-IR) and N2 physisorption. MB (methylene blue) was removed from an aqueous solution using the response surface modelling (RSM) technique, which was used for optimization reasons. All four independent factors were investigated to see how they affected the removal process: adsorbent dosage; contact time; pH; and beginning dye concentration. The rate of MB removal was strongly influenced by the pH of the solution. The Langmuir and Freundlich models were used to examine equilibrium data A for MB adsorption onto the MFA in linear and nonlinear forms. Langmuir gave a better fit. The adsorption kinetics shown by increased kinetic statistics were better characterized by a pseudo-second-order MFA model. As far as thermodynamic characteristics go, adsorption is endothermic and occurs spontaneously. It has been proven that MFA may be used as an adsorbent to remove MB dye with high efficiency, and the quadratic model has been proved to be statistically significant.

Olive stone as an eco-friendly bio-adsorbent for elimination of methylene blue dye from industrial wastewater

Adsorbents synthesized by activation and nanoparticle surface modifications are expensive and might pose health and ecological risks. Therefore, the interest in raw waste biomass materials as adsorbents is growing. In batch studies, an inexpensive and effective adsorbent is developed from raw olive stone (OS) to remove methylene blue (MB) from an aqueous solution. The OS adsorbent is characterized using scanning electron microscopy (SEM), Fourier Transform Infra-Red (FTIR), and Brunauer-Emmett-Teller (BET) surface area. Four isotherms are used to fit equilibrium adsorption data, and four kinetic models are used to simulate kinetic adsorption behavior. The obtained BET surface area is 0.9 m2 g-1, and the SEM analysis reveals significant pores in the OS sample that might facilitate the uptake of heavy compounds. The Langmuir and Temkin isotherm models best represent the adsorbtion of MB on the OS, with a maximum monolayer adsorption capacity of 44.5 mg g-1. The best dye color removal efficiency by the OS is 93.65% from an aqueous solution of 20 ppm at the OS doses of 0.2 g for 90 min contact time. The OS adsorbent serves in five successive adsorption cycles after a simple filtration-washing-drying process, maintaining MB removal efficiency of 91, 85, 80, and 78% in cycles 2, 3, 4, and 5, respectively. The pseudo second-order model is the best model to represent the adsorption process dynamics. Indeed, the pseudo second-order and the Elovich models are the most appropriate kinetic models, according to the correlation coefficient (R2) values (1.0 and 0.935, respectively) derived from the four kinetic models. The parameters of the surface adsorption are also predicted based on the mass transfer models of intra-particle diffusion and Bangham and Burt. According to the thermodynamic analysis, dye adsorption by the OS is endothermic and spontaneous. As a result, the OS material offers an efficient adsorbent for MB removal from wastewater that is less expensive, more ecologically friendly, and economically viable.

Impact of carbonization conditions and adsorbate nature on the performance of activated carbon in water treatment

The physical and chemical structure of activated carbon (AC) varies with the carbonization temperature, activation process and time. The texture and toughness of the starting raw material also determine the morphology of AC produced. The Brunauer-Emmet-Teller surface area (SBET) is small for AC produced at low temperatures but increases from 500 to 700 °C, and generally drops in activated carbons synthesized > 700 °C. Mild chemical activators and low activator concentrations tend to generate AC with high SBET compared to strong and concentrated oxidizing chemicals, acids and bases. Activated carbon from soft starting materials such as cereals and mushrooms have larger SBET approximately twice that of tough materials such as stem berks, shells and bones. The residual functional groups observed in AC vary widely with the starting material and tend to reduce under extreme carbonization temperatures and the use of highly concentrated chemical activators. Further, the adsorption capacity of AC shows dependency on the size of the adsorbate where large organic molecules such as methylene blue are highly adsorbed compared to relatively small adsorbates such as phenol and metal ions. Adsorption also varies with adsorbate concentration, temperature and other matrix parameters.

Carbon-based nanomaterials mediated adsorption and photodegradation of typical organic contaminants in aqueous fulvic acid solution

In this work, the formation of carbon-based nanomaterials-fulvic acid (CNMs-FA) composites and their capacities for the adsorption and photodegradation of typical organic contaminants in aqueous solutions were investigated. The results suggested that the formation of CNMs-FA composites was dominated by adsorbing FA on CNMs via the physisorption process, which fit the pseudo-first-order kinetic model and the Langmuir isotherm model. The formed CNMs-FA composites were characterized by using the Brunauer-Emmett-Teller, scanning electron microscopy, and infrared spectroscopy techniques and further applied for examining their effects on the adsorption and photodegradation of selected organic contaminants in aqueous solutions. The adsorption of organic contaminants on CNMs-FA composites is mainly involved in hydrogen bonding and electrostatic interactions between organic contaminants and FA species adhering to CNMs. In addition, the CNMs-FA composites are able to promote the photosensitive degradation of organic contaminants due to the photogenerated reactive species including ROS and CNMs-3FA* under sunlight irradiation. This study provided a deeper and more comprehensive understanding of the environmental behavior of CNMs in real natural surface water and clarified the underlying mechanisms.

A Two-Mediator System Based on a Nanocomposite of Redox-Active Polymer Poly(thionine) and SWCNT as an Effective Electron Carrier for Eukaryotic Microorganisms in Biosensor Analyzers

Electropolymerized thionine was used as a redox-active polymer to create a two-mediated microbial biosensor for determining biochemical oxygen demand (BOD). The electrochemical characteristics of the conducting system were studied by cyclic voltammetry and electrochemical impedance spectroscopy. It has been shown that the most promising in terms of the rate of interaction with the yeast B. adeninivorans is the system based on poly(thionine), single-walled carbon nanotubes (SWCNT), and neutral red (kint = 0.071 dm3/(g·s)). The biosensor based on this system is characterized by high sensitivity (the lower limit of determined BOD concentrations is 0.4 mgO2/dm3). Sample analysis by means of the developed analytical system showed that the results of the standard dilution method and those using the biosensor differed insignificantly. Thus, for the first time, the fundamental possibility of effectively using nanocomposite materials based on SWCNT and the redox-active polymer poly(thionine) as one of the components of two-mediator systems for electron transfer from yeast microorganisms to the electrode has been shown. It opens up prospects for creating stable and highly sensitive electrochemical systems based on eukaryotes.

New insights on manganese dioxide nanoparticles loaded on cellulose-based biochar of cassava peel for the adsorption of three cationic dyes from wastewater

Herein, a cost-effective nanomaterial with excellent adsorption capacity, simply prepared, using manganese dioxide (MnO₂) nanoparticles (NP) loaded on cellulose-based biochar of an agricultural waste, which is cassava peel carbon (CPC) and denoted as MnO₂-NP-CPC. MnO₂-NP-CPC is an environmental-friendly, and efficient adsorbent analyzed using different technics such as x-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and energy dispersive x-ray spectroscopy (EDX). MnO₂-NP-CPC was used to remove three different toxic dyes; methylene blue (MB), malachite green (MG), and rhodamine b (RB) from a single (MB), (MG), (RB), binary (MB + MG), (MG + RB), (MB + RB) and ternary (MB + MG + RB) wastewater systems, the impact of pH, adsorbent dose (2-8), initial dye concentrations (10-30 mg/L), temperature (15-35 °C) were fully studied. Furthermore, all the sorption experiments were done including adsorption isotherms, kinetics, and thermodynamics to explore all the mechanisms involved in the sorption of the three ionic dyes in single, binary, and ternary systems. The equilibrium experiments data fitted well the monolayer Langmuir isotherm for the single dye system with correlation coefficients close to 1 (0.98 for MB, 0.99 for MG, and 0.86 for RB), while the extended Langmuir and extended Freundlich isotherms were investigated to study the interaction of the three dyes in their binary systems, the obtained results indicate clearly that the sorption fellows the extended Langmuir model. Besides, the kinetic study showed the applicability of the pseudo-second model for the three dyes. Finally, the thermodynamic adsorption was controlled by physisorption, endothermic, and spontaneous in nature.

Recent advances in TiO2/ZnS-based binary and ternary photocatalysts for the degradation of organic pollutants

Semiconductor-mediated photocatalysis plays a pivotal role in the elimination of organic pollutants from water systems. Titanium dioxide (TiO₂) and zinc sulphide (ZnS) semiconductors are commonly utilized as photocatalysts in water purification due to their physical and chemical stability and also large band gap. The drawbacks of both semiconductors, nevertheless, prevent them from being used in real and large-scale treatments. Therefore, binary and ternary-based TiO₂/ZnS nanostructured materials may be a promising solution to improve the quantum efficiency, structural, and electrical features of pure TiO₂ and ZnS semiconductors for improved photoefficiency. This review aims to unravel the development of binary TiO₂/ZnS and the modification of ternary photocatalysts (TiO₂/ZnS-X, X = metal, non-metal, and dye sensitization) by various approaches. The engineered TiO₂/ZnS-based ternary nanostructured materials have exhibited exceptional performance to accelerate the degradation of organic pollutants in wastewater. These materials were fabricated by modifying TiO₂/ZnS binary composite and embedding co-catalysts like carbonaceous material, polymeric material, transition metal, metal oxide, and metal. The relationship between the properties of the resulting nanomaterials and their photocatalytic performances has been examined. This review has also placed a special focus on the synthetic routes applied to derive the binary and ternary TiO₂/ZnS composites. Another aim of this review is to scrutinize the factors that influence the performance of binary and ternary-based TiO₂/ZnS composites on the degradation of organic pollutants. Opportunities for further investigation have been also outlined, along with limitations and impediments based on the current findings.

Metal organic framework-derived recyclable magnetic coral Co@Co3O4/C for adsorptive removal of antibiotics from wastewater

The menace posed by antibiotic contamination to humanity has increased due to the absence of efficient antibiotic removal processes in the conventional waste water treatment methods from the hospitals, households, animal husbandry, and pharma industry. Importantly, only a few commercially available adsorbents are magnetic, porous, and have the ability to selectively bind and separate various classes of antibiotics from the slurries. Herein, we report the synthesis of a coral-like Co@Co3O4/C nanohybrid for the remediation of three different classes of antibiotics - quinolone, tetracycline, and sulphonamide. The coral like Co@Co3O4/C materials are synthesized via a facile room temperature wet chemical method followed by annealing in a controlled atmosphere. The materials demonstrate an attractive porous structure with an excellent surface-to-mass ratio of 554.8 m2 g-1 alongside superior magnetic responses. A time-varying adsorption study of aqueous nalidixic acid solution on Co@Co3O4/C nanohybrids indicates that these coral-like Co@Co3O4/C nanohybrids could achieve a high removal efficiency of 99.98% at pH 6 in 120 min. The adsorption kinetics data of Co@Co3O4/C nanohybrids follow a pseudo-second-order reaction kinetics suggesting a chemisorption effect. The adsorbent has also shown its merit in reusability for four adsorption-desorption cycles without showing significant change in the removal efficiency. More in-depth studies validate that the excellent adsorption capability of Co@Co3O4/C adsorbent attributing to the electrostatic and π-π interaction between adsorbent and various antibiotics. Concisely, the adsorbent manifests the potential for the removal of a wide range of antibiotics from the water alongside showing their utility in the hassle-free magnetic separation.

Functionalized agarose hydrogel with in situ Ag nanoparticles as highly recyclable heterogeneous catalyst for aromatic organic pollutants

In the present research work, a highly recyclable catalyst of Ag-based agarose (HRC-Ag/Agar) hydrogel was successfully fabricated through a simple and efficient in situ reduction method without the aid of additional surface active agent. The interaction between the rich hydroxyl functional (-OH) groups in agarose and Ag can effectively control the growth and dispersion of Ag nanoparticles (NPs) in the HRC-Ag/Agar hydrogel and keep Ag NPs free from chemical contamination, which also guarantees the reusability of HRC-Ag/Agar hydrogel as catalysts. HRC-Ag/Agar hydrogel without freeze drying and calcination was investigated for their potential applications as highly active/recyclable catalysts in reducing aromatic organic pollutants (p-nitrophenol (4-NP), methylene blue (MB) and rhodamine B (RhB)) by KBH₄. The optimal HRC-Ag/Agar-1.9 hydrogel can complete the catalytic reduction of 4-NP within 11 min. Moreover, HRC-Ag/Agar-1.9 hydrogel achieves the high conversion rate (> 99%) through ten catalytic runs. Similarly, HRC-Ag/Agar-1.9 hydrogel was able to achieve a reduction efficiency of RhB at 98% within 17 min and that of MB at 95% within 40 min. The advantages of simple synthetic procedure, no secondary pollution, strong stability and easily separated make the HRC-Ag/Agar hydrogel have great potential prospect for environmental applications.

Recent advances in new generation nanocomposite materials for adsorption of pharmaceuticals from aqueous environment

With rapid increase in the human population, a large amount of wastewater is generated every year. The availability of fresh water is decreasing at an alarming rate due to rapid industrialization and agricultural development. Pharmaceutical drugs which are credited for improving standards of life worldwide have emerged as major water contaminants, raising global concern about their potential risk to human health and environment. The presence of pharmaceutical compounds is detected in surface water (sea, river, lakes, etc.), groundwater, effluents from municipal, hospitals, and wastewater treatment plants, and even in drinking water. Efficient removal of pharmaceutical pollutants still remains a challenging task. Many techniques, including photodegradation, photocatalysis, oxidation, reverse osmosis, biodegradation, nanofiltration, adsorption, etc., have been used for the remediation of wastewater. Adsorption of pharmaceutical compounds on nanoadsorbents, as a low-cost and feasible technology, has gained immense popularity for wastewater treatment over the last decade. Adsorption techniques can be integrated with wastewater treatment plants to achieve efficient removal on an industrial level. Herein, we review the literature on the remediation techniques used for the pharmaceutical waste treatment using carbon nanotubes, metal oxides, nanoclay, and new-generation MXenes via adsorption. These materials show excellent adsorptive properties owing to their high surface area, low cost, high porosity, easy functionalization, and high surface reactivity. The adsorption mechanism of the nanoadsorbents and their reusability as a factor of sustainability have also been included in the review. The factors affecting the adsorption, including pH, the concentration of adsorbate, ionic strength, and adsorbate dose, have also been discussed.

Efficient Removal of Basic Fuchsin from Synthetic Medical Wastewater and Competitive Adsorption in the Mixture

The Ziehl-Neelsen stain is a mixture of Basic Fuchsin (BF), phenol (Ph), and methylene blue. It is used to stain the cell walls of Mycobacterium species. In this study, Basic Fuchsin was efficiently removed from synthetic wastewater using natural clay of Gankawa (GC) from Sulaimanyah city, and the effect of the presence of high concentrations of phenol in the adsorption mixture is demonstrated. In addition, X-ray diffraction (XRD), X-ray fluorescence (XRF), N2 gas adsorption analyzer, and field-emission scanning electron microscopy (FESEM) were used to characterize the natural clay. The clay was found to be mostly calcite, with a minor percentage of smectite, and contaminated with low percentages of illite. The adsorption kinetics show a relatively fast equilibration time (60-70 minutes). A second-order pseudokinetic model better fits the experimental kinetic data. The effect of the initial pH of the solution mixture was negligible at the experimental concentration range of the study. Freundlich and Langmuir’s adsorption isotherm models were applied to the equilibrium experimental data using nonlinear regression curve fitting. Both kinetics and isotherm studies point to a chemical adsorption mechanism for the process. For adsorption in the mixture, phenol molecules were found to compete with BF molecules for the active adsorption sites, while a synergetic effect of BF exists on phenol adsorption. As a naturally abundant cheap material, GC shows a superior adsorption capacity toward BF (287.0 mg g-1) over all natural materials and most of the synthetic or modified materials found in the literature.

Effective Removal of Metal ion and Organic Compounds by Non-Functionalized rGO

Effective removal of heavy metals from water is critical for environmental safety and public health. This work presents a reduced graphene oxide (rGO) obtained simply by using gallic acid and sodium ascorbate, without any high thermal process or complex functionalization, for effective removal of heavy metals. FTIR and Raman analysis show the effective conversion of graphene oxide (GO) into rGO and a large presence of defects in rGO. Nitrogen adsorption isotherms show a specific surface area of 83.5 m2/g. We also measure the zeta-potential of the material showing a value of -52 mV, which is lower compared to the -32 mV of GO. We use our rGO to test adsorption of several ion metals (Ag (I), Cu (II), Fe (II), Mn (II), and Pb(II)), and two organic contaminants, methylene blue and hydroquinone. In general, our rGO shows strong adsorption capacity of metals and methylene blue, with adsorption capacity of qmax = 243.9 mg/g for Pb(II), which is higher than several previous reports on non-functionalized rGO. Our adsorption capacity is still lower compared to functionalized graphene oxide compounds, such as chitosan, but at the expense of more complex synthesis. To prove the effectiveness of our rGO, we show cleaning of waste water from a paper photography processing operation that contains large residual amounts of hydroquinone, sulfites, and AgBr. We achieve 100% contaminants removal for 20% contaminant concentration and 63% removal for 60% contaminant concentration. Our work shows that our simple synthesis of rGO can be a simple and low-cost route to clean residual waters, especially in disadvantaged communities with low economical resources and limited manufacturing infrastructure.

Biochar-mediated removal of pharmaceutical compounds from aqueous matrices via adsorption

Pharmaceutical is one of the noteworthy classes of emerging contaminants. These biologically active compounds pose a range of deleterious impacts on human health and the environment. This is attributed to their refractory behavior, poor biodegradability, and pseudopersistent nature. Their large-scale production by pharmaceutical industries and subsequent widespread utilization in hospitals, community health centers, and veterinary facilities, among others, have significantly increased the occurrence of pharmaceutical residues in various environmental compartments. Several technologies are currently being evaluated to eliminate pharmaceutical compounds (PCs) from aqueous environments. Among them, adsorption appears as the most viable treatment option because of its operational simplicity and low cost. Intensive research and development efforts are, therefore, currently underway to develop inexpensive adsorbents for the effective abatement of PCs. Although numerous adsorbents have been investigated for the removal of PCs in recent years, biochar-based adsorbents have garnered tremendous scientific attention to eliminate PCs from aqueous matrices because of their decent specific surface area, tunable surface chemistry, scalable production, and environmentally benign nature. This review, therefore, attempts to provide an overview of the latest progress in the application of biochar for the removal of PCs from wastewater. Additionally, the fundamental knowledge gaps in the domain knowledge are identified and novel strategic research guidelines are laid out to make further advances in this promising approach towards sustainable development.

A review on activated carbon modifications for the treatment of wastewater containing anionic dyes

Polluted water resources, particularly those polluted with industrial effluents' dyes, are carcinogenic and hence pose a severe threat to sustainable and longstanding worldwide development. Meanwhile, adsorption is a promising process for polluted/wastewater treatment. In particular, activated carbon (AC) is popular among various wastewater treatment adsorbents, especially in the organic contaminants' remediation in wastewater. Hence, the AC's synthesis from degradable and non-degradable resources, the carbon activation involved in the AC synthesis, and the AC's modification to cutting-edge and effective materials have been modern-research targets in recent years. Likewise, the main research focuses worldwide have been the salient AC characteristics, such as its surface chemistry, porosity, and enhanced surface area. Notably, various modified-AC synthesis methods have been employed to enhance the AC's potential for improved contaminants-removal. Hence, we critically analyze the different modified ACs (with enhanced (surface) functional groups and textural properties) of their capacity to remove different-natured anionic dyes in wastewater. We also discuss the corresponding AC modification techniques, the factors affecting the AC properties, and the modifying agents' influence on the AC's morphological/adsorptive properties. Finally, the AC research of future interest has been proposed by identifying the current AC research gaps, especially related to the AC's application in wastewater treatment.

Exploring the Biosorption of Methylene Blue Dye onto Agricultural Products: A Critical Review

Due to their higher specific area and, in most cases, higher adsorption capacity, nanomaterials are noteworthy and attractive adsorbents. Agricultural products that are locally available are the best option for removing methylene blue (MB) dye from aqueous solutions. Because it is self-anionic, FT-IR and SEM investigations of biosorption have confirmed the role of the functional group and its contribution to the formation of pores that bind cationic dye. It is endothermic if the adsorption of MB by an adsorbent is high as the temperature increases; on the other hand, exothermic if it is high as the temperature decreases. A basic medium facilitates adsorption with respect to pH; adsorption is proportional to the initial concentration at a certain level before equilibrium; after equilibrium, adsorption decreases. A pseudo-second-order model applies for certain agricultural products. As per plotted graph for the solid-phase concentration against the liquid-phase concentration, the Langmuir adsorption isotherm model is favored; this model describes a situation in which a number of molecules are adsorbed by an equal number of available surface sites, and there is no interaction between adsorbate molecules once all sites are occupied. In contrast, the Freundlich model depicts non-ideal multi-layer sorption onto heterogeneous surfaces via numerical analysis; with a value of n = 1, the result is a linear isotherm. If the value of n < 1 or n > 1, then it is chemical or physical adsorption, respectively. Based on an EDX analysis, relevant elements are confirmed. BET analysis confirms the surface area. Nanoproducts categorized as agricultural products exhibit the aforementioned tendency. Even though nanoparticles show positive outcomes in terms of higher adsorption, a high specific area for the targeted pollutant is needed in real-world applications. In the relevant sections herein, the behavior of thermodynamic parameters, such as enthalpy, entropy, and Gibbs free energy, are examined. There is some question as to which form of agricultural waste is the most effective adsorption medium. There is no direct answer because every form of agricultural waste has its own distinct chemical and physical characteristics, such as porosity, surface area, and strength.

Preparation of lignin modified hyper-cross-linked nanoporous resins and their efficient adsorption for p-nitrophenol in aqueous solution and CO2 capture

A series of lignin modified hyper-cross-linked nanoporous resins (LMHCRs) had been synthesized from lignin, 4-vinylbenzyl chloride, and divinylbenzene by free radical polymerization reaction and following Friedel-Crafts reaction. The results indicated that Brunauer-Emmett-Teller surface area (S_BET) of LMHCRs decreased with different degrees compared with polymeric microspheres (HCRs) without adding lignin. With increasing the feeding amount of lignin, the S_BET of LMHCRs first increased and then decreased, and LMHCR-2 had larger S_BET (968.52 m²/g) and average pore size (D_A: 2.51 nm). Meanwhile, their contact angle continuously decreased from 92.1⁰ to 71.3⁰, indicating the enhanced polarity. Interestingly, the adsorption capacity of p-nitrophenol (PNP) on all LMHCRs were obviously higher than rhodamine B, and LMHCR-2 had the largest capacity ratio (3.780) of PNP to rhodamine B or other organic dyes at 298 K. Specifically, the Q_m of PNP on LMHCR-2 reached the largest value (492.1 mg/g) due to its suitable porosity and favorable surface polarity. LMHCR-2 also displayed excellent CO₂ capture (86.5 mg/g) at 273 K and 1 bar and good reusability. This study provided an efficient route to modify hyper-cross-linked resin by using the residual lignin, and showed the enhanced adsorption performance.

Adsorption of methyl violet dye onto a prepared bio-adsorbent from date seeds: isotherm, kinetics, and thermodynamic studies

Raw date seeds, as prospective natural, broadly obtainable and low-price agricultural waste for adsorbing cationic dyes from aqueous solutions, have been studied. In this work, Iraqi date seeds were prepared and characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Brunauer–Emmett–Teller (BET) surface area analysis before being used as an efficient bio-adsorbent for methyl violet (MV) dye removal. Adsorption tests were conducted with three investigated parameters, namely, time of contact, first adsorbate concentration and adsorbent dose. Compared with the pseudo first-order model (coefficient of determination = 0.9001), the pseudo second-order model was determined to be the best-fitting model with a coefficient of determination (R²) of 0.9917. The equilibrium isotherms for MV were obtained, and their ultimate capacity of adsorption was (59.5 mg g¹). Two isotherm models, Langmuir and Freundlich, were studied to fit the equilibrium data. Compared with the Freundlich isotherm model (R² = 0.8154), the Langmuir model functioned better as an adsorption isotherm with R² of 0.9837. In addition, the adsorption process was endothermic and spontaneous. The date seeds acted as active adsorbents to remove MV from the aqueous solutions in the model experiments.

Environmentally azithromycin pharmaceutical wastewater management and synergetic biocompatible approaches of loaded azithromycin@hematite nanoparticles

Pharmaceutical wastewater contamination via azithromycin antibiotic and the continuous emergence of some strains of bacteria, cancer, and the Covid-19 virus. Azithromycin wastewater treatment using the biosynthesized Hematite nanoparticles (α-HNPs) and the biocompatible activities of the resulted nanosystem were reported. Biofabrication of α-HNPs using Echinacea purpurea liquid extract as a previously reported approach was implemented. An evaluation of the adsorption technique via the biofabricated α-HNPs for the removal of the Azr drug contaminant from the pharmaceutical wastewater was conducted. Adsorption isotherm, kinetics, and thermodynamic parameters of the Azr on the α-HNPs surface have been investigated as a batch mode of equilibrium experiments. Antibacterial, anticancer, and antiviral activities were conducted as Azr@α-HNPs. The optimum conditions for the adsorption study were conducted as solution pH = 10, 150 mg dose of α-HNPs, and Azr concentration 400 mg/L at 293 K. The most fitted isothermal model was described according to the Langmuir model at adsorption capacity 114.05 mg/g in a pseudo-second-order kinetic mechanistic at R² 0.9999. Thermodynamic study manifested that the adsorption behavior is a spontaneous endothermic chemisorption process. Subsequently, studying the biocompatible applications of the Azr@α-HNPs. Azr@α-HNPs antibacterial activity revealed a synergistic effect in the case of Gram-positive more than Gram-negative bacteria. IC₅₀ of Azr@α-HNPs cytotoxicity against MCF7, HepG2, and HCT116 cell lines was investigated and it was found to be 78.1, 81.7, and 93.4 µg/mL respectively. As the first investigation of the antiviral use of Azr@α-HNPs against SARS-CoV-2, it was achieved a safety therapeutic index equal to 25.4 revealing a promising antiviral activity. An admirable impact of the use of the biosynthesized α-HNPs and its removal nanosystem product Azr@α-HNPs was manifested and it may be used soon as a platform of the drug delivery nanosystem for the biomedical applications.

Water Quality Carbon Nanotube-Based Sensors Technological Barriers and Late Research Trends: A Bibliometric Analysis

Water is the key element that defines and individualizes our planet. Relative to body weight, water represents 70% or more for the majority of all species on Earth. Taking care of water as a whole is equivalent with taking care of the entire biodiversity or the whole of humanity itself. Water quality is becoming an increasingly important component of terrestrial life, hence intensive work is being conducted to develop sensors for detecting contaminants and assessing water quality and characteristics. Our bibliometric analysis is focused on water quality sensors based on carbon nanotubes and highlights the most important objectives and achievements of researchers in recent years. Due to important measurement characteristics such as sensitivity and selectivity, or low detection limit and linearity, up to the ability to measure water properties, including detection of heavy metal content or the presence of persistent organic compounds, carbon nanotube (CNT) sensors, taking advantage of available nanotechnologies, are becoming increasingly attractive. The conducted bibliometric analysis creates a visual, more efficient keystones mapping. CNT sensors can be integrated into an inexpensive real-time monitoring data acquisition system as an alternative for classical expensive and time-consuming offline water quality monitoring. The conducted bibliometric analysis reveals all connections and maps all the results in this water quality CNT sensors research field and gives a perspective on the approached methods on this specific type of sensor. Finally, challenges related to integration of other trends that have been used and proven to be valuable in the field of other sensor types and capable to contribute to the development (and outlook) for future new configurations that will undoubtedly emerge are presented.

High-performance and selective adsorption of ZIF-8/MIL-100 hybrids towards organic pollutants

Environmental contamination by organic pollutants has become a pressing concern. In this study, metal-organic framework composites with a core-shell structure of MIL-100 wrapped around ZIF-8 (ZIF-MIL hybrids) were synthesized and characterized for their effectiveness to remove organic pollutants. First, a sequence of routine characterizations will examine the ZIF-MIL series samples' physicochemical properties and morphological characteristics. Then, the adsorption capacities of ZIF-MIL towards organic pollutants, including cationic dyes (methylene blue (MB), and rhodamine B (RHB)), anionic dyes (methyl orange (MO)), neutral pollutants (Sudan III (SD-III), tetracycline (TC) and amoxicillin (AMX)), were investigated. Among the ZIF-MIL series, ZIF-MIL-4 has an excellent specific surface area with high uptake of TC (1288 mg g^-1) and RHB (1181 mg g^-1). Based on the adsorption data from kinetic and dynamic studies, the adsorption process was closest to the pseudo-second-order kinetic model and Freundlich isotherm. In terms of thermodynamic parameter values, the adsorption of TC is an endothermic and spontaneous process, while the adsorption of RHB is an exothermic and spontaneous process. Furthermore, the reusability and selectivity studies of ZIF-MIL-4 towards TC and RHB exhibited significant regeneration ability and high selectivity. The effects of ionic strength and pH on pollutant removal efficiency were also tested. The experimental results showed that the main interactions between ZIF-MIL-4 and RHB or TC were weak coordination, electrostatic, hydrogen bonding, and π-π stacking interactions. Thus, the proposed MOF hybrid, by forming mixtures with other MOFs, can be a potential purifier with improved adsorption capacity and selectivity for organic pollutants as well as self-reusability.

A Comprehensive Insight on Adsorption of Polyaromatic Hydrocarbons, Chemical Oxygen Demand, Pharmaceuticals, and Chemical Dyes in Wastewaters Using Biowaste Carbonaceous Adsorbents

Recent trends in adsorption of hazardous organic pollutants including Polyaromatic Hydrocarbons (PAHs), Chemical Oxygen Demand (COD), Pharmaceuticals, and Chemical Dyes in wastewater using carbonaceous materials such as activated carbon (AC) and biochar (BC) have been discussed in this paper. Utilization of biomass waste in the preparation of AC and BC has gained a lot of attention recently. This review outlines the techniques used for preparation, modification, characterization, and application of the above-mentioned materials in batch studies. The approaches towards understanding the adsorption mechanisms have also been discussed. It is observed that in the majority of the studies, high removal efficiencies were reported using biowaste adsorbents. Regarding the full potential of adsorption, varying values were obtained that are strongly influenced by the adsorbent preparation technique and adsorption method. In addition, most of the studies were concentrated on the kinetic, isotherm equilibrium, and thermodynamic aspects of adsorption, suggesting the dominant isotherm and kinetic models as Langmuir or Freundlich and pseudo-second-order models. Due to development in biosorbents, adsorption has been found to be increasingly economical. However, application of these adsorbents at commercial scale has not been adequately investigated and needs to be studied. Most of the studies have been conducted on synthetic solutions that do not completely represent the discharged effluents. This also needs attention in future studies.

In situ synthesis of a porous ZrO2 coated fiber membrane for efficient static and dynamic removal of Se(iv)

High-performance static and dynamic removal of Se(iv) from environmental water was achieved by using a porous ZrO2 coated fiber membrane.

Modern Carbon-Based Materials for Adsorptive Removal of Organic and Inorganic Pollutants from Water and Wastewater

Currently, a serious threat for living organisms and human life in particular, is water contamination with persistent organic and inorganic pollutants. To date, several techniques have been adopted to remove/treat organics and toxic contaminants. Adsorption is one of the most effective and economical methods for this purpose. Generally, porous materials are considered as appropriate adsorbents for water purification. Conventional adsorbents such as activated carbons have a limited possibility of surface modification (texture and functionality), and their adsorption capacity is difficult to control. Therefore, despite the significant progress achieved in the development of the systems for water remediation, there is still a need for novel adsorptive materials with tunable functional characteristics. This review addresses the new trends in the development of new adsorbent materials. Herein, modern carbon-based materials, such as graphene, oxidized carbon, carbon nanotubes, biomass-derived carbonaceous matrices-biochars as well as their composites with metal-organic frameworks (MOFs) and MOF-derived highly-ordered carbons are considered as advanced adsorbents for removal of hazardous organics from drinking water, process water, and leachate. The review is focused on the preparation and modification of these next-generation carbon-based adsorbents and analysis of their adsorption performance including possible adsorption mechanisms. Simultaneously, some weak points of modern carbon-based adsorbents are analyzed as well as the routes to conquer them. For instance, for removal of large quantities of pollutants, the combination of adsorption and other methods, like sedimentation may be recommended. A number of efficient strategies for further enhancing the adsorption performance of the carbon-based adsorbents, in particular, integrating approaches and further rational functionalization, including composing these adsorbents (of two or even three types) can be recommended. The cost reduction and efficient regeneration must also be in the focus of future research endeavors. The targeted optimization of the discussed carbon-based adsorbents associated with detailed studies of the adsorption process, especially, for multicomponent adsorbate solution, will pave a bright avenue for efficient water remediation.

A review on water treatment technologies for the management of oxoanions: prospects and challenges

Oxoanions are a class of contaminants that are easily released into the aquatic systems either through natural or anthropogenic activities. Depending on their oxidation states, they are highly mobile, resulting in the contamination of underground water. Above the permissible level in groundwater, they pose as threats to mammals when the contaminated water is consumed. Some of the health challenges caused are cancer, neurological, cardiac, gastrointestinal, and skin disorders. Several treatment technologies have been adopted over the years for the management of these oxoanions present in the aquatic systems. However interesting these treatment technologies might be, they also have their limitations such as cost-effectiveness, the complexity of the process, and generation of secondary pollutants. This work focused on some of the water treatment technologies applied for the removal of oxoanions. Some of the advantages and disadvantages of these treatment technologies are also highlighted. Amongst all the treatment technologies, adsorption is the most applied method for the removal of oxoanions. However, photocatalysis has a higher prospect since it is non-selective and secondary pollutants are not generated after the treatment process. Also, photocatalysis can simultaneously reduce and oxidise oxoanions as well as organic pollutants respectively.

CuO-ZnO-CdWO4: a sustainable and environmentally benign photocatalytic system for water cleansing

Currently, there is a major problem of water contaminations, especially of dyes, all over the world. A new technique is being developed daily for the treatment of contaminated water. In many ways, a photocatalytic degradation of a dye by a mixed metal oxide photocatalyst is counted as the best technique for water treatment. This paper also addresses the preparation and photocatalytic application of newly developed mixed metal oxide nanocomposite, CuO-ZnO-CdWO₄. A novel mixed metal oxide CuO-ZnO-CdWO₄ nanocomposite has been synthesized by a green route using Brassica Rapa leaves extract. The application of CuO-ZnO-CdWO₄ as a photocatalyst in wastewater treatment has been thoroughly discussed. Several spectroscopic and microscopic techniques were used to characterize the prepared nanocomposite. The photocatalytic activity of CuO-ZnO-CdWO₄ nanocomposite with a band gap of 3.13 eV was observed under the artificial visible light and sunlight for the degradation of Congo red dye. The results under sunlight show the 1.45 times greater removal efficiency than under the artificial visible light. Pseudo-first-order, diffusion, and Singh kinetics models were used to describe the kinetics of dye degradation. Pseudo-first-order model was found to be best fitted model for present study. The performance of CuO-ZnO-CdWO₄ was estimated by significant parameters such as quantum yield, figure of merit, turnover number, and mean turnover frequency. The value these parameters were calculated as 1.70 × 10^-8 molecules photon^-1, 1.77 × 10^-4, 2.98 × 10⁸ s^-1, and 3.31 × 10^-4 s^-1, respectively. These parameters revealed high potential of CuO-ZnO-CdWO₄ for Congo red dye degradation.

Adsorption of phenanthrene onto magnetic multi-walled carbon nanotubes (MMWCNTs) influenced by various fractions of humic acid from a single soil

In the present study, two magnetic multi-walled carbon nanotubes (MMWCNTs) with different ratios of Fe²⁺/Fe³⁺ were prepared, and the effects of different fractions of dissolved humic acid (DHA) on the adsorption of phenanthrene by multi-walled carbon nanotubes (MWCNTs) and MMWCNTs from the aqueous solution were investigated. The adsorption kinetics of DHA₁ and DHA₄ were best fitted with pseudo-second order model. The adsorption of DHAs on MMWCNTs was weaker than that on MWCNTs, and DHA₁ was easier to adsorb to MWCNTs and MMWCNTs than DHA₄. The phenanthrene adsorption capacities by 1:2:1MMWCNTs and 4:2:1MMWCNTs with higher polar groups and magnetic gradient were less than that of MWCNTs. The pH value had no obvious effect on the adsorption of phenanthrene to MWCNTs loaded with different iron. Additionally, the DHAs could form soluble complexes of DHAs-Fe (II) in solution to reduce the phenanthrene adsorption on MMWCNTs, DHA₁ inhibit more obviously phenanthrene adsorbed onto MWCNTs and MMWCNTs than DHA₄. As for MMWCNTs, the main mechanisms of phenanthrene adsorbed onto it included new adsorption sites formed by π-π interaction and magnetic gradient. In this study, MMWCNTs after adsorbed DHAs had a weaker inhibitory effect on phenanthrene adsorption than MWCNTs, implying that when phenanthrene is adsorbed by DHAs-coated MMWCNTs, the bioavailability and mobility of phenanthrene will be reduced, and it is easy to be removed by the magnet for further processing.

Silver nanoparticles protect against arsenic induced genotoxicity via attenuating arsenic bioaccumulation and elevating antioxidation in mammalian cells

Arsenic (As) and its compounds have been classified as Group I carcinogenic agents by the International Agency for Research on Cancer (IARC); however, there is few specific and efficient antidotes used for As detoxification. The present study aimed to investigate the protective effects of silver nanoparticles (AgNPs) at non-toxic concentrations on As(Ⅲ) induced genotoxicity and the underlying mechanism. Our data showed that AgNPs pretreatment significantly inhibited the generation of phosphorylated histone H2AX (γ-H2AX, marker of nuclear DNA double strand breaks) and the mutation frequencies induced by As(Ⅲ) exposure. Atomic fluorescence spectrometer (AFS) and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) analysis revealed that the intracellular accumulation of As(Ⅲ) in human-hamster hybrid A_L cells was declined by AgNPs via suppressing the expression of specific As(Ⅲ)-binding protein (Gal-1). Moreover, the activities of antioxidant enzymes were greatly up-regulated by AgNPs, which eventually inhibited the generation of reactive oxygen species (ROS) induced by As(Ⅲ) and the downstream stress-activated protein kinases/c-Jun amino-terminal kinases (SAPK/JNK) signaling pathway. These results provided clear evidence that AgNPs dramatically suppressed the genotoxic response of As(Ⅲ) in mammalian cells via decreasing As(Ⅲ) bioaccumulation and elevating intracellular antioxidation, which might provide a new clue for AgNPs applications in As(Ⅲ) detoxification.

Applications of Green Synthesized Nanomaterials in Water Remediation

Water is the most important component on the earth for living organisms. With industrial development, population increase and climate change, water pollution becomes a critical issue around the world. Its contamination with different types of pollutants created naturally or due to anthropogenic activities has become the most concerned global environmental issue. These contaminations destroy the quality of water and become harmful to living organisms. A number of physical, chemical and biological techniques have been used for the purification of water, but they suffer in one or the other respect. The development of nanomaterials and nanotechnology has provided a better path for the purification of water. Compared to conventional methods using activated carbon, nanomaterials offer a better and economical approach for water remediation. Different types of nanomaterials acting as nanocatalysts, nanosorbents, nanostructured catalytic membranes, bioactive nanoparticles, nanomembranes and nanoparticles provide an alternative and efficient methodology in solving water pollution problems. However, the major issue with nanomaterials synthesized in a conventional way is their toxicity. In recent days, a considerable amount of research is being carried out on the synthesis of nanomaterials using green routes. Nanomaterials synthesized by using the green method are now being used in different technologies, including water remediation. The remediation of water by using nanomaterials synthesized by the green method has been reviewed and discussed in this paper.