Influence of ligand chemistry on silver nanoparticles for colorimetric detection of Cr3+ and Hg2+ ions

Recent advances and trends in innovative biosensor-based devices for heavy metal ion detection in food

Low-cost, reliable, and efficient biosensors are crucial in detecting residual heavy metal ions (HMIs) in food products. At present, based on distance-induced localized surface plasmon resonance of noble metal nanoparticles, enzyme-mimetic reaction of nanozymes, and chelation reaction of metal chelators, the constructed optical sensors have attracted wide attention in HMIs detection. Besides, based on the enrichment and signal amplification strategy of nanomaterials on HMIs and the construction of electrochemical aptamer sensing platforms, the developed electrochemical biosensors have overcome the plague of low sensitivity, poor selectivity, and the inability of multiplexed detection in the optical strategy. Moreover, along with an in-depth discussion of these different types of biosensors, a detailed overview of the design and application of innovative devices based on these sensing principles was provided, including microfluidic systems, hydrogel-based platforms, and test strip technologies. Finally, the challenges that hinder commercial application have also been mentioned. Overall, this review aims to establish a theoretical foundation for developing accurate and reliable sensing technologies and devices for HMIs, thereby promoting the widespread application of biosensors in the detection of HMIs in food.

Extraction of heavy metals from wastewater using amine-modified mesoporous silica

Presence of heavy metals in wastewater is a critical environmental issue, and efficient extraction of the metals remains a challenging task. In this study, the adsorption behavior of Ce(III), Hg(II), and Cu(II) metal ions using MCM-48 material modified with acid and base functional groups was examined. The modified materials were characterized using various techniques, including XRD, BET, FT-IR, NMR, and SEM, which revealed that the materials' properties remained unchanged after modification. The adsorption capacity of the modified materials for metal ions was then evaluated and was found that the amine-modified MCM-48 material exhibited the highest adsorption efficiency. Precisely, the amine-modified material achieved an adsorption capacity of 97% for Ce(III), 98% for Hg(II), and 90% for Cu(II) after 180 min of adsorption. These results highlight the effectiveness of amine functionalization in enhancing the adsorption capacity of silica material for heavy metals.

Synthesis of multicolor silver nanostructures for colorimetric sensing of metal ions (Cr3+, Hg2+ and K+) in industrial water and urine samples with different spectral characteristics

In this work, we have synthesized four different color (yellow, orange, green, and blue (multicolor)) silver nanostructures (AgNSs) by chemical reduction method where silver nitrate, sodium borohydride and hydrogen peroxide were used as reagents. The as-synthesized multicolor AgNSs were successfully functionalized with bovine serum albumin (BSA) and applied as a colorimetric sensor for the assaying of metal cations (Cr³⁺, Hg²⁺, and K⁺). The addition of metal ions (Cr³⁺, Hg²⁺, and K⁺) into BSA functionalized AgNSs (BSA-AgNSs) causes the aggregation of BSA-AgNSs, and are accompanied by visual color changes with red or blue shift in the surface plasmon resonance (SPR) band of BSA-AgNSs. The BSA-AgNSs show different SPR characteristic for each metal ions (Cr³⁺, Hg²⁺, and K⁺) with exhibiting different spectral shift and color change. The yellow color BSA-AgNSs (Y-BSA-AgNSs) act as a probe for sensing Cr³⁺, orange color BSA-AgNSs (O-BSA-AgNSs) act as probe for Hg²⁺ ion assay, green color BSA-AgNSs (G-BSA-AgNSs) act as a probe for the assaying of both K⁺ and Hg²⁺, and blue color BSA-AgNSs (B-BSA-AgNSs) act as a sensor for colorimetric detection of K⁺ ion. The detection limits were found to be 0.26 μM for Cr³⁺ (Y-BSA-AgNSs), 0.14 μM for Hg²⁺ (O-BSA-AgNSs), 0.05 μM for K⁺ (G-BSA-AgNSs), 0.17 μM for Hg²⁺ (G-BSA-AgNSs), and 0.08 μM for K⁺ (B-BSA-AgNSs), respectively. Furthermore, multicolor BSA-AgNSs were also applied for assaying of Cr³⁺, and Hg²⁺ in industrial water samples and K⁺ in urine sample.

Development of piperazine conjoined 1,2,3-triazolyl-γ-propyltriethoxysilanes: Fluorometric detection of Cr3+ ions and computational study

Chromium is essential for some biochemical processes, and excess is a big concern that shows adverse effects on human health and the environment. Therefore, it is urgent to design new sensors to detect chromium ions rapidly. The present study discusses the synthesis of piperazine conjoined 1,2,3-triazolyl-γ-propyltriethoxysilanes (4a-4b) and development of 4a as fluorescence turn-on sensor for the detection of Cr³⁺ ions. The mechanistic insights reveal to the restricted CN rotation and inhibited intramolecular charge transfer (ICT) process. In addition, Job's plot and Benesi-Hildebrand plot justify the 1:1 binding affinity with a binding constant of 9.96 × 10⁵ M^-1 for [ligand 4a + Cr³⁺] complex and the limit of detection for Cr³⁺ ions is observed as 6.06 × 10^-8 M. The fluorescence spectral changes, ¹H NMR spectra and DFT studies provide evidences for ligand 4a and Cr³⁺ ions interactions. Further, the reversibility of the ligand 4a from [ligand 4a + Cr³⁺] complex on the addition of EDTA can be used in the construction of molecular logic gate where Cr³⁺ and EDTA are considered as inputs and the fluorescence intensity at 398 nm as output. Further, compounds 4a-4b were then evaluated for their antibacterial activity against bacterial strains (Escherichia coliand Staphylococcus aureus), revealing a modest activity. The binding mode of ligand 4a to Staphylococcus aureus (PDB ID - 3U2K) and Escherichia coli (PDB ID - 5Z4O) was investigated using an in-silico molecular docking technique, which revealed that the triazole ring and silanyl group are involved in hydrogen bonding with proteins and may be the cause of the ligand's antibacterial activity. The ligand 4a demonstrated a high affinity for binding within the active sites of proteins with binding energies of -7.97 kcal/mol (3U2K) and -8.68 kcal/mol (5Z4O).

Specifically functionalized MTT-Ag NP/SA film sensor for the ultrasensitive detection of Hg2+ in lettuce samples

In the present study, highly efficient 5-Methyl-1,3,4-thiadiazole-2-thiol-modified silver nanoparticles (MTT-Ag NPs) were successfully synthesized and could be used for convenient and sensitive detection of Hg2+. MTT acts as a protective agent by forming Ag-S bonds with Ag NPs, meantime, MTT can also be captured Hg2+ through NN bonds. Furthermore, to improve the sustainability and stability of MTT-Ag NPs, sodium alginate (SA) was used as a substrate material for the formation of SA-MTT-Ag NPs films. As expected, SA-MTT-Ag NPs could be stored for more than 180 days at room temperature. When used SA-MTT-Ag NPs thin films as colourimetric sensors for detection of Hg2+ in lettuce, the low detection limit could be down to 0.22 μM (44 ppb) with wide linear range (0-1 µM and 1-150 µM) and good recovery (96.25 % - 98.75 %). Therefore, the method enables highly selective and efficient monitoring of Hg2+ in food samples.

Detection of heavy metal ion in real samples with fiber based paper based on new rare earth cluster

Chromium (Cr) is an important material, but also one of the most toxic heavy metal pollutants, showing great threat to human health and ecological environment, thus, accurate and rapid detection of Cr³⁺ has far-reaching significance. In this work, based on the ligand of 2,3,4,5,6-pentafluorobenzoic acid (HPFBA) that does not contains oscillation effect group such as "CH, OH, and NH bond", three rare earth dinuclear cluster of Ln₂(PFBA)₆(phen)₂(H₂O)₂ (Ln = Tb³⁺1-Tb, Eu³⁺1-Eu, Gd³⁺1-Gd, phen = 1,10-phenanthroline) were obtained. 1-Tb shows excellent stability and luminescence properties. In depth investigation reveals that 1-Tb shows quick detection towards Cr³⁺ in water through luminescence "turn-off", with extremely short response time of 1.0 min, very low limit of detection (LOD) of 5.2 ppb and no interference from other ions. The LOD value is much lower than the total content of chromium for water in China (15 ppm, GB9078-1996). In the actual environment such as tap water, lake water, human, and serum, 1-Tb shows excellent detection and recovery rate for Cr³⁺. More interestingly, a fiber based paper of test paper that based on 1-Tb and ordinary filter paper was fabricated, which can probe Cr³⁺ by visible color changes to the naked eye under UV light.

Detection of heavy metal ions using laser-induced breakdown spectroscopy combined with filter paper modified with PtAg bimetallic nanoparticles

The rapid and sensitive detection of heavy metal ions is important for environment and human health. Hence, the rapid and sensitive detection of multiple heavy metals simultaneously has become a critical issue. Here, we propose a method based on laser-induced breakdown spectroscopy (LIBS) combined with filter paper modified with PtAg bimetallic nanoparticles (BNPs) (LIBS-FP-PtAgBNPs) for the ultrasensitive detection of Hg²⁺, Cr³⁺, and Pb²⁺. The PtAgBNPs-modified filter paper was used to efficiently and specifically adsorb Hg, Cr, and Pb, and LIBS was used to detect the Hg, Cr, and Pb simultaneously. The limits of detection for Hg, Cr, and Pb were 0.5 μg/L (2.5 nM), 8 μg/L (0.15 μM), and 2 μg/L (9 nM), respectively. Furthermore, this method was successfully applied to determine the concentrations of Hg, Cr, and Pb in real spiked water samples. Compared with other methods based on nanoparticle sensing, LIBS-FP-PtAgBNPs is simpler to use and can achieve highly efficient enrichment, rapid separation, and sensitive detection of heavy metal ions. The optimal detections of Hg, Cr, and Pb were achieved in the pH range of 1-6. The developed method provides a new avenue to realize the rapid and sensitive detection of trace heavy metals in the environment.

Colorimetric detection of heavy metal ions with various chromogenic materials: Strategies and applications

Detection of heavy metal ions has drawn significant attention in environmental and food area due to their threats to the human health and ecosystem. Colorimetry is one of the most frequently-used methods for the detection of heavy metal ions owing to its simplicity, easy operation and rapid on-site detection. The development of chromogenic materials and their sensing mechanisms are the key research direction in the area of colorimetric method. Since each chromogenic material has their unique optical and chemical properties, they have totally different colorimetric sensing mechanisms. This review focuses on the chromogenic materials and their sensing strategies for the colorimetric detection of heavy metal ions. We divide the chromogenic materials into three types, including organic materials, inorganic materials, and other materials. As for each type of chromogenic material, we discuss their detailed sensing strategies, sensing performance, and real sample applications. Moreover, current challenges and perspectives related to the colorimetry of heavy metal ions are also discussed in this review. The aim of this review is to help readers to better understand the principles of colorimetric methods for heavy metal ions and push the development of rapid detection of heavy metal ions.

Selective detection of tartaric acid using amino acid interlinked silver nanoparticles as a colorimetric probe

A variety of biomolecules with different functional groups play critical roles in almost all the processes occurring in living cells. Interaction of metallic nanoparticles (NPs) with various biomolecules generates a layer of molecules on their surface, and this biomolecular rich layer formed on the NP surface is described as a "biomolecular corona". The physicochemical properties of the NPs, including size, adsorption affinity, and charge on the particles' surfaces are the major factors influencing the characteristics of this corona. The formation of various biomolecular corona has been studied well, whereas the amino acid corona is relatively new by exploring their stability. In the present study, a novel formation of an amino acid corona with a fundamental interaction mechanism for a selective detection procedure using a colorimetric platform has been proposed. Herein, amino acid-coated silver NPs (AgNPs) have been used as a template with spectroscopic (steady state UV-Vis, FTIR) and imaging (HR-TEM, DLS) techniques. Our findings demonstrated that among different amino acid coronas, glutathione (GSH) stabilized AgNPs show a rapid reaction with tartaric acid. The extent and thermodynamics of the formed complex between the GSH/AgNPs and tartaric acid have also been studied and this suggested that the complex formed is spontaneous and energy releasing in nature.

Identification of heavy metal ions from aqueous environment through gold, Silver and Copper Nanoparticles: An excellent colorimetric approach

Heavy metal pollution has become a severe threat to human health and the environment for many years. Their extensive release can severely damage the environment and promote the generation of many harmful diseases of public health concerns. These toxic heavy metals can cause many health problems such as brain damage, kidney failure, immune system disorder, muscle weakness, paralysis of the limbs, cardio complaint, nervous system. For many years, researchers focus on developing specific reliable analytical methods for the determination of heavy metal ions and preventing their acute toxicity to a significant extent. The modern researchers intended to utilize efficient and discerning materials, e.g. nanomaterials, especially the metal nanoparticles to detect heavy metal ions from different real sources rapidly. The metal nanoparticles have been broadly utilized as a sensing material for the colorimetric detection of toxic metal ions. The metal nanoparticles such as Gold (Au), Silver (Ag), and Copper (Cu) exhibited localized plasmon surface resonance (LPSR) properties which adds an outstanding contribution to the colorimetric sensing field. Though, the stability of metal nanoparticles was major issue to be exploited colorimetric sensing of heavy emtal ions, but from last decade different capping and stabilizing agents such as amino acids, vitmains, acids and ploymers were used to functionalize the metal surface of metal nanoparticles. These capping agents prevent the agglomeration of nanoparticles and make them more active for prolong period of time. This review covers a comprehensive work carried out for colorimetric detection of heavy metals based on metal nanoparticles from the year 2014 to onwards.

Statistical optimization of silver nanoparticle synthesis by green tea extract and its efficacy on colorimetric detection of mercury from industrial waste water

For the optimization of silver nanoparticle production, a central composite design was used with three parameters: AgNO₃ concentration, green tea extract concentration, and temperature at three different levels. The size of the synthesized silver nanoparticle, its UV absorbance, zeta potential, and polydispersity index were set as the response parameters. Silver nanoparticles obtained in the optimization process were characterized and its efficacy on colorimetric detection of mercury was evaluated. The response variables were significant for the factors analyzed, and each variable had a significant model (P < 0.05). The ideal conditions were: 1 mM AgNO₃, 0.5% green tea extract, and 80 °C temperature. To analyze the produced AgNPs under certain ideal conditions, Fourier transform infrared spectroscopy (FTIR), dynamic light scattering (DLS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) were used. The UV-visible spectra of AgNPs revealed an absorption maxima at 424 nm. The XRD pattern reveals a significant diffraction peak at 38.25°, 44.26°, 64.43°, and 77.49°, which corresponds to the (111), (200), (220), and (311) planes of polycrystalline face-centered cubic (fcc) silver, respectively. The TEM and SEM analyses confirmed that the particles were spherical, and dynamic light scattering study determined the average diameter of AgNPs to be 77.4 nm. The AgNPs have a zeta potential of -62.6 mV, as determined by the zeta sizer analysis. The AgNPs detects mercury at a micromolar concentration. Furthermore, the environmentally friendly generated AgNPs were used to detect mercury in a colorimetric method that was effectively employed for analytical detection of Hg²⁺ ions in an aqueous environment for the purpose of practical application.

Simultaneous detection of aqueous aluminum(III) and chromium(III) using Persea americana reduced and capped silver nanoparticles

There is a significant interest to develop sensing devices that detect water toxins, especially heavy metal ions. Although there have already been numerical reports on detecting toxic heavy metal ions, the use of adaptable devices could enable a broader range of sensing applications. Here, we used fresh peel extract (PeA) and dried peel extract (DPeA) of Persea americana (Avocado) as a reducing and capping agent to synthesize and stabilize AgNPs. The dimensions of NPs were controlled by tuning pH, temperature, and volume of the reducing agent. The sensitivity and selectivity of the AgNPs toward various metal ions viz. Ni(II), Cd(II), Al(III), Hg(II), Cr(III), Ba(II), Pb(II), Zn(II), Co(II), Mn(II), Cu(II), Ca(II), Mg(II), and K(I) were studied. The detection probe was found to be selective and sensitive toward Al(III) and Cr(III) ions with the detection limit of 0.04 ppm and 0.05 ppm, respectively. High-resolution transmission electron microscope (HRTEM), ultraviolet-visible (UV-Vis) spectroscopy, and dynamic light scattering (DLS) analysis results confirm an agglomeration-based mechanism for sensing both metal ions. This method can be exploited for the colorimetric detection of toxic heavy metals in real water samples.

The synthesis of novel fluorescent bimetal nanoclusters for aqueous mercury detection based on aggregation-induced quenching

In this research, new bimetal nanoclusters (DAMP-AuAg BNCs) with 4,6-diamino-2-mercaptopyrimidine (DAMP) as a reducing agent and stabilizer ligand were exploited. The nanoclusters displayed excellent fluorescent properties, very small size, good stability, and water solubility. It was found that the as-prepared DAMP-AuAg BNCs exhibited strong fluorescent emission at 640 nm under an excitation wavelength of 473 nm with a large Stokes shift of 167 nm, and the red fluorescence could be readily quenched with aqueous Hg²⁺. The DAMP-AuAg BNCs showed good specificity and sensitivity toward Hg²⁺ in aqueous solution, and the fluorescence analysis of Hg²⁺ showed a wide linear range from 0.85 μM to 246 μM and a detection limit of 20 nM. It is demonstrated that strong Hg²⁺-Au⁺ interactions led to the aggregation of nanoclusters, which caused the quenching of the fluorescence, and the affinity of Hg²⁺ for nitrogen should also be considered. Due to the relevant good performance of DAMP-AuAg BNCs, they were applied to the fluorescence analysis of Hg²⁺ in real water samples and were found to be a potential fluorescent sensor for aqueous mercury ions.

Selective colorimetric and electrochemical detections of Cr(III) pollutant in water on 3-mercaptopropionic acid-functionalized gold plasmon nanoparticles

Gold plasmon nanoparticle (AuNP) was applied to the detection and the quantification of pollutant Cr(III) in water. It was synthesized by the chemical reduction of tetrachloroauric(III) acid with sodium citrate as a reducing and capping agent and was modified with 3-mercaptopropanoic acid (3-mpa) to improve the sensing recognition for the metal ion in the colorimetric detection. The 3-mpa-deposited AuNP selectively bound Cr(III) among the other 14 metal cations, resulting in the redshift of the gold plasmon band from 521 nm to 670 nm. The colorimetric quantification examination of the Cr(III) using the plasmon intensity approved the high sensitivity with the low limit of detection (0.34 ppb). Meanwhile, for the electrochemical detection, AuNP was electrochemically deposited on indium tin oxide glass substrate, modified with 3-mpa, attached Cr(III), and subsequently capped with 3-mpa-deposited AuNP. The cathodic current peak at -0.84 V versus the metal ion concentration revealed the linearity at a wide concertation range of 200-5000 ppb. As a result, the proposed colorimetric and electrochemical sensing techniques, which are the simple and facile detectors, can be complementarily employed with a high selectivity, sensitivity and wide analyte concentration range for the quantification of Cr(III) in aqueous solutions.

Colorimetric detection of Cr3+ in dietary supplements using a smartphone based on EDTA and tannic acid-modified silver nanoparticles

A simplistic, portable and low-cost method for the rapid detection of Cr³⁺ was developed based on a smartphone readout and a co-functionalized silver nanoparticles (AgNPs) system for use as an on-site device in resource-poor areas. The presence of Cr³⁺ induced aggregation of AgNPs through coordinated complex formation between Cr³⁺ and stabilizing agents on the NPs surface, resulted in a bright yellow of an AgNPs solution turned to wine red along with a SPR band was red-shifted from 429 nm to 625 nm. A smartphone with an available free application, called "PhotoMetrix" was used to measure the RGB (red, green, blue) values of the color intensities in the AgNPs system and convert into Cr³⁺ concentration by using univariate calibration curves in less than 60s. This smartphone-based detection system showed a high selectivity of AgNPs with Cr³⁺ and gave a positive coefficient correlation (R² = 0.9878) between the intensity of channel R and the Cr³⁺ concentration, with a linear range of 2.0-5.0 mg L^-1, and a detection limit of 1.52 mg L^-1. Furthermore, the proposed method has been successfully applied for quantification of Cr³⁺ in dietary supplement samples. The results obtained were in close agreement with those obtained in FAAS (Flame Atomic Absorption Spectrometry). The developed colorimetric system based on a smartphone readout device exhibits feasibility and reliability for on-site Cr³⁺ detection in the real samples.

Colorimetric detection of Cr6+ ions based on surface plasma resonance using the catalytic etching of gold nano-double cone @ silver nanorods

Hexavalent chromium ion (Cr⁶⁺) is highly toxic to human health and environment. Herein, high-performance detection of Cr⁶⁺ is of great import. In this study, a rapid and sensitive multicolor colorimetric method for detection of Cr⁶⁺ in aqueous solution was established on the basis of Cr⁶⁺ etching of gold nano-double cone@silver nanorods (Au NDC@Ag NRs). Au NDC@Ag NRs was synthesized by a modified seed-mediated growth method. The catalytic etching induced by Cr⁶⁺ changed the morphology of Au NDC@Ag NRs, leading to the attenuation of surface plasma resonance (SPR) and the redshift of absorption spectra. Meanwhile, Au NDC@Ag NRs exhibits obvious color changes from orange to pink, to purple, and finally becomes colorless with the increasing concentrations of Cr⁶⁺. With such a design, naked-eye detection of Cr⁶⁺ was realized with high sensitivity. The proposed multicolor sensing method showed a good linearity between the redshift change of absorption peak (△λ) and the concentrations of Cr⁶⁺ in the range from 2.5 to 40 μM. The limit of detection (LOD) was calculated as 1.69 μM in aqueous solution. In addition, successful detection of Cr⁶⁺ in tap water and Yangtze River water, indicating the real applications of Au NDC@Ag NRs probe in monitoring Cr⁶⁺ in environment.

Highly selective and sensitive tool for the detection of Hg(II) using 3-(Trimethoxysilyl) propyl methacrylate functionalized Ag-Ce nanocomposite from real water sample

Mercury and its derivates cause distinct toxicity and it is detrimental to the ecosystem where the excessive concentration contributes towards the environmental pollutants. The current study reported a colorimetric method for the detection of Hg(II) ion with high specificity and selectivity using Ag-Ce nanocomposite (NC) functionalized by 3-(Trimethoxysilyl) propyl methacrylate. The synthesized Ag-Ce NC was characterized by using double beam UV-visible spectrophotometer, zeta sizer, EDS, TEM, FT-IR, XRD and particle size analyzer. The synthesized particle possessed an average particle size of 27 ± 1 nm and zeta potential of -39.32 ± 3 mV. The brownish yellow colored Ag-Ce NC changed to colorless in presence of Hg(II) where the colorimetric detection was extremely specific and superior towards Hg(II) ion on comparing the tests with other metal ions. An excellent linear correlation was observed between absorbance (395 nm) and Hg(II) concentrations (1 nM-10 μM) (R² = 0.988) with LOD of 0.03 nM. A cotton swab based probe was prepared for selective, elegant and low cost colorimetric method to detect Hg(II). The parametric study was performed for optimizing the suitable condition. The colorimetric probe developed by this study for Hg(II) detection using Ag-Ce NC shows excellent practical applicability.

Molecule-gated surface chemistry of Pt nanoparticles for constructing activity-controllable nanozymes and a three-in-one sensor

Herein, a simple strategy for constructing activity-controllable nanozymes is proposed based on the glutathione (GSH)-gated surface chemistry of citrate-capped Pt nanoparticles (PtNPs). PtNPs have been shown to have oxidase-like activity that can effectively catalyze the oxidation of 3,3',5,5'-tertamethylbenzidine (TMB) by O2, resulting in a typical color reaction from colorless to blue. We found that GSH can inhibit the oxidase-like activity of PtNPs as a molecule-gated surface chemistry element, resulting in a dramatic decrease of the oxidation of TMB. The addition of copper ions (Cu2+) could oxidize GSH into glutathione disulfide (GSSG), resulting in the distinct suppression of GSH-modulated PtNP surface chemistry and oxidase-like activity inhibition, which further results in a significant acceleration of TMB oxidation and the obvious recovery of intense blue color. Furthermore, the color-based detection signal associated with the redox of TMB indicator here was found to show good fluorescence and a photothermal effect and exhibit sensitive and selective response toward the proposed molecule-gated surface chemistry and Cu2+ target. On the basis of this phenomenon, we successfully constructed a three-in-one sensor for Cu2+ with a triple signal readout, colorimetric, photothermal (temperature), and fluorescence, depending on the proposed in situ modulation method for PtNP catalysis. The applicability of the three-in-one sensor was also demonstrated by measuring Cu2+ in human serum with a standard addition method, and the results are of satisfactory accuracy as confirmed by ICP-MS measurements.

Dual Colorimetric Sensor for Hg2+/Pb2+ and an Efficient Catalyst Based on Silver Nanoparticles Mediating by the Root Extract of Bistorta amplexicaulis

Environmental pollution derivated from toxic metals and organic toxins is becoming a serious issue worldwide because of their harmful effects on the ecosystem and human health. Here we are reporting an extremely selective and cost-effective colorimetric sensor for simultaneous recognition of Hg2+ and Pb2+ by using green synthesized silver nanoparticles (AgNPs) mediated from the environmental friendly roots extract of Bistorta amplexicaulis. Biogenic synthesized AgNPs were well-characterized by various spectroscopic techniques e.g., UV-vis, FT-IR, XRD, AFM, and Zetasizer. The photophysical potential of synthesized AgNPs toward common metal cations was explored via absorption spectroscopy and colorimetric assay. The hypsochromic shift in the SPR band of AgNPs can easily be detected through naked eyes vision from dark brown to light yellow in the case of Hg2+. A substantial reduction in the absorbance of AgNPs was recorded upon mixing with Pb2+. AgNPs based colorimetric sensor is highly sensitive toward Hg2+ and Pb2+ with a limit of detection (LOD) of 8.0 × 10-7 M and 2.0 × 10-7 M for Hg2+ and Pb2+, respectively. Furthermore, AgNPs showed promising catalytic activity for the degradation of methyl orange dye. These results demonstrate that Bistorta amplexicaulis stabilized silver nanoparticles have potential applications as a colorimetric sensor and an effective catalyst for the degradation of methyl orange.

Case study on the use of image analysis for the simple and inexpensive colorimetric detection of Fe(iii) in water

In the present work, we have reported a simple and cost effective colorimetric method for the detection of Fe(iii) in water. The method is based on the color change through the formation of an Fe(iii)-glycine complex at room temperature. This type of complex formation produces an intense color due to the ligand to metal charge transfer (LMCT). The rate of this type of complex formation depends appreciably on the Fe(iii) concentrations. An important aspect of the present work is that here the image analysis technique has been used successfully for the discrimination of the color obtained by the variation of the Fe(iii) concentration. The fundamental spectro-photochemical studies on the colorimetric detection of Fe(iii) by forming a metal ligand complex and thereafter the discrimination of the complex through image analysis can provide effective insight into the development of cost effective devices for the detection of liquid phase analytes.

Simultaneous measurement of Cr(III) and Cu(II) based on indicator-displacement assay using a colorimetric nanoprobe

High-performance analysis of heavy metal ions is great importance in both environment and food safety. In this work, a facile and reliable colorimetric sensor was presented for simultaneous detection of Cu²⁺ and Cr³⁺ based on indicator-displacement assay (IDA). As a typical silicate nanomaterials, ZnSiO₃ hollow nanosphere (ZSHS) exhibited an outstanding ion exchange capacity. Zincon was incorporated with the ZSHS to form a zincon/ZSHS hybrid ionophore with a blue color. Upon the addition of Cr³⁺, IDA reaction and selective ion exchange occurred with the color change of zincon/ZSHS ionophore from blue to yellow. With such a design, colorimetric measurement of Cr³⁺ was realized. The linear concentration for Cr³⁺ detection ranged from 0.5 μM to 75 μM with the LOD of 83.2 nM. Furthermore, we also screened different kinds of complexing agents that may respond with zincon/ZSHS ionophore and various metal ions. It was found that tartaric acid (TA) showed the chelation capability of Zn²⁺-TA is stronger than that of Zn²⁺-zincon. Thus zincon/ZSHS/TA presented a yellow color due to the chelation reaction of Zn²⁺-TA, releasing the zincon as a free state. After addition of Cu²⁺, a stronger chelation reaction of Cu²⁺-zincon occurred. This process involved in the color change from yellow to blue and realized colorimetric measurement of Cu²⁺. The detection limit of Cu²⁺ was calculated to be 43.7 nM with linear range from 0.1 to 20 μM. In addition, the zincon/ZSHS nanoprobe was successfully applied for simultaneous measurement of Cu²⁺ and Cr³⁺ in sorghum and river water, indicating that the zincon/ZSHS nanoprobe provided a promising sensing platform in environment and food safety.

Simple hydrothermal approach for synthesis of fluorescent molybdenum disulfide quantum dots: Sensing of Cr3+ ion and cellular imaging

Nowadays, fluorescent molybdenum disulfide quantum dots (MoS₂ QDs) have proven to be potential candidates in the sensing and bioimaging areas owing to their exceptional intrinsic characteristics. Here, a simple hydrothermal strategy was explored for the preparation of MoS₂ QDs using ammonium heptamolybdate and 6-mercaptopurine (6-MP) as precursors. The emission peak of MoS₂ QDs was significantly quenched in the presence Cr³⁺ ion due to the selective surface chemistry on the surfaces of MoS₂ QDs. The designed fluorescent MoS₂ QDs showed a linear fluorescence quenching response with increasing concentration of Cr³⁺ ion (0.1-10 μM), allowing to detect Cr³⁺ ion even at 0.08 μM. This fluorescent MoS₂ QDs were utilized for the quantification of Cr³⁺ ion in real samples (water and biological samples). Interestingly, the synthesized MoS₂ QDs exhibited negligible cytotoxicity on NRK cells and acted as good candidates for imaging of Trichoderma viride fungal cells.

Rapid colorimetric detection of mercury using silver nanoparticles in the presence of methionine

Development of potential sensors is inevitable for the detection of environmental pollutants including toxins, organic pollutants and heavy metal which cause hazardous effect to human and other living organisms. The present study is to develop silver nanoparticle (Ag NPs) based sensor for the accurate, sensitive and selective colorimetric detection of Hg²⁺ ions from aqueous samples at nano molar level. The nanoparticles were synthesized chemically and it was stabilized by polyvinylpyrrolidone (PVP). The prepared particles were characterized by UV-visible spectroscopy, scanning electron microscopy (SEM), particle analysiser and Zetasizer. The UV-visible spectra of Ag NPs showed absorbance maximum at 392 nm. The average diameter of Ag NPs was determined to be 6 ± 0.9 nm by using particle analyzer. The zeta sizer analysis showed that the PVP stabilized Ag NPs possessed a zeta potential of -35.56 ± 3 mV. The Ag NPs-methionine conjugate showed the colour change from the brownish yellow colour to colourless when it was reacted with mercury. The Ag NPs conjugated methionine is sensitive to mercury and detects the mercury at nano molar level. The influence of other metal ion did not interfere with the detection and quantification of Hg²⁺. The detection of Hg²⁺ was also performed with paper strip and agarose gel method. The Ag NPs conjugate with methionine can applied for the detection of Hg²⁺ from various aqueous samples.

Gum acacia-based silver nanoparticles as a highly selective and sensitive dual nanosensor for Hg(ii) and fluorescence turn-off sensor for S2− and malachite green detection

A facile and green method was adopted to synthesize highly selective gum acacia-mediated silver nanoparticles as dual sensor (fluorescence turn-on and colorimetric) for Hg(ii) and fluorescence turn-off sensor for S²⁻ and malachite green. The mechanism proposed for a dual response towards Hg(ii) is the redox reaction between Ag(0) and Hg(ii), resulting in the formation of Ag(i) and Hg(0) and electron transfer from gum acacia to Ag(i), which further leads to the formation of an Ag@Hg nanoalloy. The enhanced fluorescence signal was quenched selectively by S²⁻ owing to the formation of Ag₂S and HgS. The reported nanosensor was found to be useful for sensing malachite green via the inner filter effect. The linear ranges were 3 nmol L⁻¹ to 13 μmol L⁻¹ for Hg(ii), 3–170 μmol L⁻¹ for S²⁻ and 7–80 μmol L⁻¹ for malachite green, and the corresponding detection limits were 2.1 nmol L⁻¹ for Hg(ii), 1.3 μmol L⁻¹ for S²⁻ and 1.6 μmol L⁻¹ for malachite green.

Gum acacia-stabilized silver nanoparticles for the detection of Hg(ii), S²⁻ and malachite green.

Noble Metal Nanoparticles-Based Colorimetric Biosensor for Visual Quantification: A Mini Review

Nobel metal can be used to form a category of nanoparticles, termed noble metal nanoparticles (NMNPs), which are inert (resistant to oxidation/corrosion) and have unique physical and optical properties. NMNPs, particularly gold and silver nanoparticles (AuNPs and AgNPs), are highly accurate and sensitive visual biosensors for the analytical detection of a wide range of inorganic and organic compounds. The interaction between noble metal nanoparticles (NMNPs) and inorganic/organic molecules produces colorimetric shifts that enable the accurate and sensitive detection of toxins, heavy metal ions, nucleic acids, lipids, proteins, antibodies, and other molecules. Hydrogen bonding, electrostatic interactions, and steric effects of inorganic/organic molecules with NMNPs surface can react or displacing capping agents, inducing crosslinking and non-crosslinking, broadening, or shifting local surface plasmon resonance absorption. NMNPs-based biosensors have been widely applied to a series of simple, rapid, and low-cost diagnostic products using colorimetric readout or simple visual assessment. In this mini review, we introduce the concepts and properties of NMNPs with chemical reduction synthesis, tunable optical property, and surface modification technique that benefit the development of NMNPs-based colorimetric biosensors, especially for the visual quantification. The “aggregation strategy” based detection principle of NMNPs colorimetric biosensors with the mechanism of crosslinking and non-crosslinking have been discussed, particularly, the critical coagulation concentration-based salt titration methodology have been exhibited by derived equations to explain non-crosslinking strategy be applied to NMNPs based visual quantification. Among the broad categories of NMNPs based biosensor detection analyses, we typically focused on four types of molecules (melamine, single/double strand DNA, mercury ions, and proteins) with discussion from the standpoint of the interaction between NMNPs surface with molecules, and DNA engineered NMNPs-based biosensor applications. Taken together, NMNPs-based colorimetric biosensors have the potential to serve as a simple yet reliable technique to enable visual quantification.

Colorimetric and naked eye detection of trace Hg2+ ions in the environmental water samples based on plasmonic response of sodium alginate impregnated by silver nanoparticles

Water pollution with mercury is a global concern. Therefore, establishing a rapid and accurate detection method is urgently required. Nanosensors can be a perfect alternative to instrument detection. In order to overcome low sustainability of sensors, a new composite nanosensor of sodium alginate- silver nanoparticles (SA-AgNPs) was synthesized by solvent casting method and used in colorimetric and naked eye detection of trace Hg²⁺ ions in water samples. The structural features of the produced nanosensor were characterized by instrumental techniques. The obtained results confirmed the formation of AgNPs with an average size of 13.34 nm. The colorimetric sensing of Hg²⁺ was carried out under specific conditions (pH = 6 and reaction time of 7 min) with a linear correlation obtained between the absorbance at 402 nm and different Hg²⁺ ion concentrations within the range of 0.025 μM-60 μM. The synthesized composite nanosensor of SA-AgNPs detected Hg²⁺ ions with a detection limit (LOD) of 5.29 nM. In addition, this sensor was successfully applied to detect Hg²⁺ ions in the environmental water samples with recoveries within the range of 81.58% to 114.73%. The produced nanosensor exhibited good selectivity toward Hg²⁺ ions in the presence of several competing ions.

Synthesis of Calixarene-Capped Silver Nanoparticles for Colorimetric and Amperometric Detection of Mercury (HgII, Hg0)

Calixarene-functionalized water dispersible silver nanoparticles have been synthesized and characterized on the basis of UV-vis, IR, X-ray diffraction, and high-resolution transmission electron microscopy analysis, and their sensing properties toward metal ions have been investigated. They selectively detect Hg2+ and Hg0 in solution and vapor phases, respectively, with distinct color change. Interference study with mixture of metal ions revealed no interference from any other metal ions used in this study. Their mechanism of detection involved Hg2+-aided displacement of calixarene moiety from the surface of the functionalized nanoparticles, followed by the formation of Ag-Hg amalgam due to interaction of Hg2+ with Ag0 and also the formation of assembly of Ag0 nanoparticles by dipole-dipole interaction of the bare-surfaced nanoparticles. Electrochemical study revealed that with the aid of functionalized nanoparticles, Hg2+ can be detected amperometrically with high sensitivity. The detection limits obtained for Hg2+ by UV-vis study and amperometry are 0.5 nM (0.1 ppb) and 10 nM (2 ppb), respectively. The new material has been used to detect Hg2+ in aqueous real sample and Hg0 in soil sample.

A novel and ultrasensitive yellow to taupe brown colorimetric sensing and removal method for Hg(ii) based on the thermosensitive poly(N-isopropyl acrylamide) stabilized silver nanoparticles

AgNP/PNIPAm was developed as a dual-functional colorimetric probe and removal system for Hg²⁺.

Plasmonic nanoprobes based on the shape transition of Au/Ag core–shell nanorods to dumbbells for sensitive Hg-ion detection

Sensitive plasmonic nanoprobes for the sensitive detection of mercury ions based on a “rod-like to dumbbell or not” morphology transition of the Au/Ag core–shell hybrid nanorods.

Independent spectral characteristics of functionalized silver nanoparticles for colorimetric assay of arginine and spermine in biofluids

A colorimetric assay for selective and sensitive detection of arginine and spermine using 6-ATT-AgNPs as a probe.