Comparison study on the ammonium adsorption of the biochars derived from different kinds of fruit peel

Physicochemical properties and performance of non-woody derived biochars for the sustainable removal of aquatic pollutants: A systematic review

Biochar is a carbon-rich material produced from the partial combustion of different biomass residues. It can be used as a promising material for adsorbing pollutants from soil and water and promoting environmental sustainability. Extensive research has been conducted on biochars prepared from different feedstocks used for pollutant removal. However, a comprehensive review of biochar derived from non-woody feedstocks (NWF) and its physiochemical attributes, adsorption capacities, and performance in removing heavy metals, antibiotics, and organic pollutants from water systems needs to be included. This review revealed that the biochars derived from NWF and their adsorption efficiency varied greatly according to pyrolysis temperatures. However, biochars (NWF) pyrolyzed at higher temperatures (400-800 °C) manifested excellent physiochemical and structural attributes as well as significant removal effectiveness against antibiotics, heavy metals, and organic compounds from contaminated water. This review further highlighted why biochars prepared from NWF are most valuable/beneficial for water treatment. What preparatory conditions (pyrolysis temperature, residence time, heating rate, and gas flow rate) are necessary to design a desirable biochar containing superior physiochemical and structural properties, and adsorption efficiency for aquatic pollutants? The findings of this review will provide new research directions in the field of water decontamination through the application of NWF-derived adsorbents.

Understanding the dependence of biochar properties on different types of biomass

Owing to the diversity of biomasses and many variables in pyrolysis process, the property of biochar from varied biomass feedstock or even same biomass could differ significantly. Since the property of biochar governs the further application of biochar, this review paid particular attention to the correlation between the nature of biomass feedstock and the specifications of biochar in terms of yield, elemental composition, pH, functionalities, heating value, pore structures, morphologies, etc. The property of the biochar from the pyrolysis of cellulose, hemicellulose, lignin, woody biomass (pine, mallee, poplar, acacia, oak, eucalyptus and beech), bark of woody biomass, leaves of woody biomass, straw, algae, fruit peels, tea waste was compared and summarized. In addition, the differences of the biochar of these varied origins were also analyzed. The remaining questions, about the correlation of biomass nature with biochar characteristics, to be further investigated are analyzed in detail. The deduced information about the relationship of the nature of biochar and biomass feedstock as well as key pyrolysis parameters is of importance for further development of the methods for tailoring or production of the biochar of desirable properties. The results from this study could be interesting technically and commercially for the technology developer using biochar as the source of carbon in different applications.

Simultaneous removal of ammonium, phosphate, and phenol via self-assembled biochar composites CBCZrOFe3O4 and its utilization as soil acidity amelioration

High concentrations of ammonium, phosphate, and phenol are recognized as water pollutants that contribute to the degradation of soil acidity. In contrast, small quantities of these nutrients are essential for soil nutrient cycling and plant growth. Here, we reported composite materials comprising biochar, chitosan, ZrO, and Fe3O4, which were employed to mitigate ammonium, phosphate, and phenol contamination in water and to lessen soil acidity. Batch adsorption experiments were conducted to assess the efficacy of the adsorbents. Initially, comparative studies on the simultaneous removal of NH4, PO4, and phenol using CB (biochar), CBC (biochar + chitosan), CBCZrO (biochar + chitosan + ZrO), and CBCZrOFe3O4 (biochar + chitosan + ZrO + Fe3O4) were conducted. The results discovered that CBCZrOFe3O4 exhibited the highest removal percentage among the adsorbents (P < 0.05). Adsorption data for CBCZrOFe3O4 were well fitted to the second-order kinetic and Freundlich isotherm models, with maximum adsorption capacities of 112.65 mg/g for NH4, 94.68 mg/g for PO4 and 112.63 mg/g for phenol. Subsequently, the effect of CBCZrOFe3O4-loaded NH4, PO4, and phenol (CBCZrOFe3O4-APP) on soil acidity was studied over a 60-day incubation period. The findings showed no significant changes (P < 0.05) in soil exchangeable acidity, H+, Mg, K, and Na. However, there was a substantial increase in the soil pH, EC, available P, CEC, N-NH4, and N-NO3. A significant reduction was also observed in the available soil exchangeable Al and Fe (P < 0.05). This technique demonstrated multi-functionality in remediating water pollutants and enhancing soil acidity.

Feasibility study of Aesculus turbinata fruit shell-derived biochar for ammonia removal in wastewater and its subsequent use as nitrogen fertilizer

In the face of increasing nitrogen demand for crop cultivation driven by population growth, this study presents a sustainable solution to address both the heightened demand and the energy-intensive process of nitrogen removal from wastewater. Our approach involves the removal of nitrogen from wastewater and its subsequent return to the soil as a fertilizer. Using biochar derived from Aesculus turbinata fruit shells (ATFS), a by-product of post-medical use, we investigated the effect of pyrolysis temperature on the NH4-N adsorption capacity of ATFS biochar (ATFS-BC). Notably, the ATFS-BC pyrolyzed at 300 °C (ATFS-BC300) exhibited the highest NH4-N adsorption capacity of 15.61 mg/g. The superior performance of ATFS-BC300 was attributed to its higher number of oxygen functional groups and more negatively charged surface, which contributed to the enhanced NH4-N adsorption. The removal of NH4-N by ATFS-BC300 involved both physical diffusion and chemisorption, with NH4-N forming a robust multilayer adsorption on the biochar. Alkaline conditions favored NH4-N adsorption by ATFS-BC300; however, the presence of trivalent and divalent ions hindered this process. Rice plants were cultivated to assess the potential of NH4-N adsorbed ATFS-BC300 (NH4-ATFS-BC300) as a nitrogen fertilizer. Remarkably, medium doses of NH4-ATFS-BC300 (594.5 kg/ha) exhibited key agronomic traits similar to those of the commercial nitrogen fertilizer in rice seedlings. Furthermore, high doses of NH4-ATFS-BC300 demonstrated superior agronomic traits compared to the commercial fertilizer. This study establishes the viability of utilizing ATFS-BC300 as a dual-purpose solution for wastewater treatment and nitrogen fertilizer supply, presenting a promising avenue for addressing environmental challenges.

Ammonium ion removal from aqueous solutions in the presence of organic compounds, using biochar from banana leaves. Competitive isotherm models

Industrial, e.g. food industrial and domestic wastewaters contain huge amount of compounds causing eutrophication, and should be removed with high cost during wastewater treatment. However, these compounds could be utilized as fertilizers too. Biochar can remove a wide range of pollutants from water, such as ammonium, which can be found in relatively high concentration in dairy wastewaters. However, adsorption performance may be affected by the presence of other wastewater pollutants. Thus, this study aims to determine the efficiency of biochar as an adsorbent of ammonium in aqueous solutions in the presence of some selected organic compounds of typical dairy wastewaters such as bovine serum albumin (BSA), lactose, and acetic acid. Methods: The biochar was produced from banana leaves at 300 °C, modified with NaOH, and characterized by Scanning Electron Microscope - Energy Dispersive X-Ray Spectroscopy (SEM-EDX), Fourier-transform infrared spectra (FTIR) analysis, and specific surface area measurements. Batch experiments were carried out to investigate the ammonium adsorption capacity and the ion competitive adsorption mechanism. Significant Findings: Results show that the surface structure of the biochar derived from banana leaves is different from other biochars previously studied; although the specific surface area is not very considerable and despite having nitrogen within the elemental composition, the biochar studied is capable of adsorbing 2.60 mg NH4+/m2, the highest ammonium removal in 2 h occurs at pH 9 and 500 mg biochar dose. Langmuir model in the monolayer phase analysis fits better for all scenarios and the maximum NH4+ adsorption capacity was 0.97 mg/g without organic compounds. In the multilayer adsorption phase, the isotherm model that best fits the data obtained is the Harkins-Jura model without organic compounds. The presence of organic compounds in the aqueous solution significantly impacts the adsorption of ammonium by biochar since it improves the adsorption capacity (1.132 mg/g BSA, 0.975 mg/g lactose, and 1.874 mg/g acetic acid). The Aranovich-Donohue isotherm model fitted the data obtained during ion competitive adsorption experiments well.

Advancements in application of modified biochar as a green and low-cost adsorbent for wastewater remediation from organic dyes

Synthetic organic dyes, which are resistant to biodegradation, pose a notable health risk, potentially leading to cancer and respiratory infections. Researchers have addressed this concern by exploring physicochemical methods to remove organic dyes from wastewater. A particularly promising solution involves modified biochar adsorbents, which demonstrate high efficiency in organic dye removal. Biochar, a charcoal-like material derived from biomass pyrolysis, offers advantages such as low cost, eco-friendliness, high efficiency and reusability. Beyond its role in sustainable soil remediation, biochar proves effective in removing organic dyes from wastewater after undergoing physical or chemical modification. Acid-base activation or metal-heteroatom impregnation enhances biochar's adsorption capacity. This comprehensive review examines the attributes of biochar, common methods for production and modification, and the impacts of raw materials, pyrolysis temperature, heating rate and residence time. It further elucidates the biochar adsorption mechanism in the removal of organic dyes, assessing factors influencing efficiency, including biochar feedstock, solution pH, adsorption temperature, particle size, initial dye concentration, biochar dosage and reaction time. It explores challenges, opportunities, reusability and regeneration methods of biochar in treating organic dye wastewater. It also discusses recent advances in organic dye removal using adsorption-based biochar. The review ultimately advocates for enhancing biochar's adsorption performance through post-modification.

Physicochemical assessment of ammonium adsorption using a palm shell-based adsorbent activated with acetic acid: experimental and theoretical studies

The adsorption of ammonium from water was studied on an activated carbon obtained using raw oil palm shell and activated with acetic acid. The performance of this adsorbent was tested at different operating conditions including the solution pH, adsorbent dosage, and initial ammonium concentration. Kinetic and equilibrium studies were carried out, and their results were analyzed with different models. For the adsorption kinetics, the pseudo-first order equation was the best model to correlate this system. Calculated adsorption rate constants ranged from 0.071 to 0.074 g/mg min. The ammonium removal was 70-80% at pH 6-8, and it was significantly affected by electrostatic interaction forces. Ammonium removal (%) increased with the adsorbent dosage, and neutral pH condition favored the adsorption of this pollutant. The best ammonium adsorption conditions were identified with a response surface methodology model where the maximum removal was 91.49% with 2.27 g/L of adsorbent at pH 8.11 for an initial ammonium concentration of 36.90 mg/L. The application of a physical monolayer model developed by statistical physics theory indicated that the removal mechanism of ammonium was multi-ionic and involved physical interactions with adsorption energy of 29 kJ/mol. This activated carbon treated with acetic acid is promising to depollute aqueous solutions containing ammonium.

Reducing nitrogen loss from farmland by layered double hydroxide-supported carbon dots-enhanced ammonium immobilization

It remains a significant challenge to develop a kind of cost-effective and eco-friendly adsorbent with strong immobilization capabilities for ammonium in farmland. In this work, we employed Ca/Al layered double hydroxide-supported carbon dots (CDs@Ca/Al-LDHs) as a novel and efficient adsorbent for ammonium immobilization both in aqueous and soil environments. Such a composite could exhibit a high adsorption capacity towards ammonium in solution, which was four times higher than zeolite and three times higher than biochar under the same conditions. The mechanism investigations revealed that electrostatic interactions between the negatively charged CDs and the positively charged ammonium played a key role in the adsorption. In 30-day leaching experiments, the fabricated composite cumulatively reduced ammonium and nitrate by 6.3% and 9.7%, respectively at a dosage of 0.1% (w/w). Incubation experiments further confirmed that the developed composite could effectively inhibit ammonia volatilization and nitrification by immobilizing the ammonium within soil matrices. Our results demonstrated that CDs@Ca/Al-LDHs represented a promising candidate for cost-effective and eco-friendly immobilization of excess ammonium from over-fertilized farmland.

Pristine and modified biochar applications as multifunctional component towards sustainable future: Recent advances and new insights

Employing biomass for environmental conservation is regarded as a successful and environmentally friendly technique since they are cost-effective, renewable, and abundant. Biochar (BC), a thermochemically converted biomass, has a considerably lower production cost than the other conventional activated carbons. This material's distinctive properties, including a high carbon content, good electrical conductivity (EC), high stability, and a large surface area, can be utilized in various research fields. BC is feasible as a renewable source for potential applications that may achieve a comprehensive economic niche. Despite being an inexpensive and environmentally sustainable product, research has indicated that pristine BC possesses restricted properties that prevent it from fulfilling the intended remediation objectives. Consequently, modifications must be made to BC to strengthen its physicochemical properties and, thereby, its efficacy in decontaminating the environment. Modified BC, an enhanced iteration of BC, has garnered considerable interest within academia. Many modification techniques have been suggested to augment BC's functionality, including its adsorption and immobilization reliability. Modified BC is overviewed in its production, functionality, applications, and regeneration. This work provides a holistic review of the recent advances in synthesizing modified BC through physical, chemical, or biological methods to achieve enhanced performance in a specific application, which has generated considerable research interest. Surface chemistry modifications require the initiation of surface functional groups, which can be accomplished through various techniques. Therefore, the fundamental objective of these modification techniques is to improve the efficacy of BC contaminant removal, typically through adjustments in its physical or chemical characteristics, including surface area or functionality. In addition, this article summarized and discussed the applications and related mechanisms of modified BC in environmental decontamination, focusing on applying it as an ideal adsorbent, soil amendment, catalyst, electrochemical device, and anaerobic digestion (AD) promoter. Current research trends, future directions, and academic demands were available in this study.

Efficient Adsorption of Nitrogen and Phosphorus in Wastewater by Biochar

Nitrogen and phosphorus play essential roles in ecosystems and organisms. However, with the development of industry and agriculture in recent years, excessive N and P have flowed into water bodies, leading to eutrophication, algal proliferation, and red tides, which are harmful to aquatic organisms. Biochar has a high specific surface area, abundant functional groups, and porous structure, which can effectively adsorb nitrogen and phosphorus in water, thus reducing environmental pollution, achieving the reusability of elements. This article provides an overview of the preparation of biochar, modification methods of biochar, advancements in the adsorption of nitrogen and phosphorus by biochar, factors influencing the adsorption of nitrogen and phosphorus in water by biochar, as well as reusability and adsorption mechanisms. Furthermore, the difficulties encountered and future research directions regarding the adsorption of nitrogen and phosphorus by biochar were proposed, providing references for the future application of biochar in nitrogen and phosphorus adsorption.

A review of metallurgical slags as catalysts in advanced oxidation processes for removal of refractory organic pollutants in wastewater

With the rapid growth of the metallurgical industry, there is a significant increase in the production of metallurgical slags. The waste slags pose significant challenges for their disposal because of complex compositions, low utilization rates, and environmental toxicity. One promising approach is to utilize metallurgical slags as catalysts for treatment of refractory organic pollutants in wastewater through advanced oxidation processes (AOPs), achieving the objective of "treating waste with waste". This work provides a literature review of the source, production, and chemical composition of metallurgical slags, including steel slag, copper slag, electrolytic manganese residue, and red mud. It emphasizes the modification methods of metallurgical slags as catalysts and the application in AOPs for degradation of refractory organic pollutants. The reaction conditions, catalytic performance, and degradation mechanisms of organic pollutants using metallurgical slags are summarized. Studies have proved the feasibility of using metallurgical slags as catalysts for removing various pollutants by AOPs. The catalytic performance was significantly influenced by slags-derived catalysts, catalyst modification, and process factors. Future research should focus on addressing the safety and stability of catalysts, developing green and efficient modification methods, enhancing degradation efficiency, and implementing large-scale treatment of real wastewater. This work offers insights into the resource utilization of metallurgical slags and pollutant degradation in wastewater.

Comparing the mechanisms of syntrophic volatile fatty acids oxidation and methanogenesis recovery from ammonia stress in regular and biochar-assisted anaerobic digestion: Different roads lead to the same goal

Biochar has been recognized as a promising additive to mitigate ammonia inhibition during syntrophic methanogenesis, while the key function of biochar in this process is still in debates. This study clarified the distinct mechanisms of syntrophic volatile fatty acids -oxidizing and methanogenesis recovery from ammonia inhibition in regular and biochar-assisted anaerobic digestion. Under 5 g/L ammonia stress, adding biochar shortened the methanogenic lag time by 10.9% and dramatically accelerated the maximum methane production rate from 60.3 to 94.7 mLCH4/gVSsludge/d. A photometric analysis with a nano-WO3 probe revealed that biochar enhanced the extracellular electron transfer (EET) capacity of suspended microbes (Pearson's r = -0.98), confirming that biochar facilitated methanogenesis by boosting EET between syntrophic butyrate oxidizer and methanogens. Same linear relationship between EET capacity and methanogenic rate was not observed in the control group. Microbial community integrating functional genes prediction analysis uncovered that biochar re-shaped syntrophic partners by enriching Constridium_sensu_stricto/Syntrophomonas and Methanosarcina. The functional genes encoding Co-enzyme F420 hydrogenase and formylmethanofuran dehydrogenase were upregulated by 1.4-2.3 times, consequently enhanced the CO2-reduction methanogenesis pathway. Meanwhile, the abundances of gene encoding methylene-tetrahydrofolate transformation, a series of intermediate processes involved in acetate oxidation, in the biochar-assisted group were 28.2-63.7% higher than these in control group. Comparatively, Methanosaeta played a pivotal role driving aceticlastic methanogenesis in the control group because the abundance of gene encoding acetyl-CoA decarbonylase/synthase complex increased by 1.9 times, suggesting an aceticlastic combining H2-based syntrophic methanogenesis pathway was established in control group to resist ammonia stress. A 2nd period experiment elucidated that although depending on distinct mechanisms, the volatile fatty acid oxidizers and methanogens in both groups developed sustained and stable strategies to resist ammonia stress. These findings provided new insights to understand the distinct methanogenic recovery strategy to resist toxic stress under varied environmental conditions.

Enhanced simultaneous removal of phosphate and ammonium from swine wastewater using magnetic magnesium-loaded Chinese herbal medicine residues: Performance, mechanism, and resource utilization

Magnetic magnesium (Mg)-loaded Chinese herbal medicine residues (MM-TCMRs) were fabricated to simultaneously remove and recover phosphate and ammonium from wastewater. The MM-TCMRs exhibited larger specific surfaces and rougher structures with massive spherical particles than those of original residues. They could be separated by adjusting the magnetic field. The phosphate and ammonium adsorption by MM-TCMRs were matched with the pseudo-second-order model, while the Langmuir model yielded the maximum adsorption capacities of 635.35 and 615.57 mg g-1, respectively. Struvite precipitation on the MM-TCMRs surface was the primary removal mechanism with electrostatic attraction, ligand exchange, intra-particle diffusion, and ion exchange also involved. The recyclability of MM-TCMRs confirmed their good structural stability. More importantly, the nutrient-loaded MM-TCMRs enhanced alfalfa growth and improved soil fertility in planting experiments. Collectively, the MM-TCMRs are promising candidates for nutrient removal and recovery from wastewater.

An overview of characteristic factors of biochar as a soil improvement tool in rice growth- A review

Biochar is a growing tool for bioremediation and soil improvement applications. Researchers are focusing on biochar due to its efficacy, eco-friendly composition, and cost-effective solutions to a variety of environmental issues. In recent times biochar has been used in enhancing the soil, increasing nutrient content, and sequestering carbon in paddy cultivation soils. India and Southeast Asian countries consume paddy as a major source of food in large quantities. Therefore, improving the growth condition of paddy fields using an easily available and safe technique will help increase the production rate. This will fulfill the needs of the growing population. Biochar is developed by the thermal decomposition of organic materials in low or no oxygen through pyrolysis, gasification, and co-pyrolysis methods. It improves paddy soil fertility due to its special physicochemical properties such as porosity, high surface area, efficient slow release, nutrient holding capacity, and maintenance of soil microbiota. Considering the importance of biochar in paddy soil fertility, the present work reviews the sources of biochar, functionalization of biochar, mechanism, and beneficial role of biochar.

Biomass based biochar production approaches and its applications in wastewater treatment, machine learning and microbial sensors

Biochar is a stable carbonaceous material derived from various biomass and can be utilized as adsorbents, catalysts and precursors in various environmental applications. This review discusses various feedstock materials and methods of biochar production via traditional as well as modern approaches. Additionally, the biochar characteristics, HTC process, and its modification by employing steam and gas purging, acidic, basic / alkaline and organo-solvent, electro- and magnetic fields have been discussed. The recent biochar applications for real water, wastewater and industrial wastewater for the abstraction of environmental contaminants also reviewed. Moreover, applications in machine learning and microbial sensors were discussed. In the meantime, analyses on commercial and environmental profit, current ecological concerns and the future directions of biochar application have been well presented.

Development of a novel three-dimensional biofilm-electrode system (3D-BES) loaded with Fe-modified biochars for enhanced pollutants removal in landfill leachate

Different mass ratio iron (Fe)-loaded biochars (FeBCs) were prepared from food waste and used in the three-dimensional biofilm-electrode systems (3D-BES) as particular electrodes for landfill leachate treatment. Compared to the unmodified biochar (BC), specific surface area of Fe-loaded biochars (FeBC-3 with a Fe: biochar of 0.2:1) increased from 63.01 m2/g to 184.14 m2/g, and pore capacity increased from 0.038 cm3/g to 0.111 cm3/g. FeBCs provided more oxygen-containing functional groups and exhibited excellent redox properties. Installed with FeBC-3 as particular electrode, both NH4+-N and chemical oxygen demand COD removals in 3D-BESs were well fitted with the pseudo-first-order model, with the maximum removal efficiencies of 98.6 % and 95.5 %, respectively. The batch adsorption kinetics experiments confirmed that the maximum NH4+-N (7.5 mg/g) and COD (21.8 mg/g) adsorption capacities were associated closely with the FeBC-3 biochar. In contrast to the 3D-BES with the unmodified biochar, Fe-loaded biochars significantly increased the abundance of microorganisms being capable of removing organics and ammonia. Meanwhile, the increased content of dehydrogenase (DHA) and electron transport system activity (ETSA) evidenced that FeBCs could enhance microbial internal activities and regulate electron transfer process among functional microorganisms. Consequently, it is concluded that Fe-loaded biochar to 3D-BES is effective in enhancing pollutant removals in landfill leachate and provided a reliable and effective strategy for refractory wastewater treatment.

Effect of Post-Washing on Textural Characteristics of Carbon Materials Derived from Pineapple Peel Biomass

Porous carbon materials have been widely used to remove pollutants from the liquid-phase streams. However, their limited pore properties could be a major problem. In this work, the effects of post-washing methods (i.e., water washing and acid washing) on the textural characteristics of the resulting biochar and activated carbon products from pineapple peel biomass were investigated in the carbonization and CO2 activation processes. The experiments were set at an elevated temperature (i.e., 800 °C) holding for 30 min. It was found that the enhancement in pore property reached about a 50% increase rate, increasing from 569.56 m2/g for the crude activated carbon to the maximal BET surface area of 843.09 m2/g for the resulting activated carbon by water washing. The resulting activated carbon materials featured the microporous structures but also were characteristic of the mesoporous solids. By contrast, the enhancement in the increase rate by about 150% was found in the resulting biochar products. However, there seemed to be no significant variations in pore property with post-washing methods. Using the energy dispersive X-ray spectroscopy (EDS) and the Fourier Transform infrared spectroscopy (FTIR) analyses, it showed some oxygen-containing functional groups or complexes, potentially posing the hydrophilic characters on the surface of the resulting carbon materials.

Banana Peel Derived Chitosan-Grafted Biocomposite for Recovery of NH4+ and PO43

Biomass-derived adsorbents afford accessible and inexpensive harvesting of nitrogen and phosphorus from wastewater sources. Human urine is widely accepted as a rich source of nitrogen and phosphorus. However, direct use of urine in agriculture is untenable because of its unpleasant smell, pathogen contamination, and pharmaceutical residues. In this work, we have grafted chitosan onto dried and crushed banana peel (DCBP) to generate the biocomposite DCBP/Ch. A combination of FTIR, TGA, XRD, FESEM, EDX, and NMR analyses were used to characterize DCBP/Ch and reveal condensation-aided covalent conjugation between O-H functionalities of DCBP and chitosan. The adsorption performance of DCBP/Ch toward NH4+ and PO43- is in sync with its attractive surface porosity, elevated crystallinity, and thermostability. The maximum adsorption capacity of DCBP/Ch toward NH4+/PO43- was estimated as 42.16/15.91 mg g-1 at an operating pH of 7/4, respectively, and ranks highly when compared to previously reported bioadsorbents. DCBP/Ch performs admirably when tested on artificial urine. While nitrogen and phosphorus harvesting from human urine using single techniques has been reported previously, this is the first report of a single adsorbent for recovery of NH4+ and PO43-. The environmental compatibility, ease of preparation, and economic viability of DCBP/Ch present it as an attractive candidate for deployment in waste channels.

Synthesis, Characterization, and Biosorption of Cu2+ and Pb2+ Ions from an Aqueous Solution Using Biochar Derived from Orange Peels

In this study, orange peel (OP) biochar was used as a bio-sorbent for the removal of copper and lead from wastewater in single and binary systems. The equilibrium and kinetic studies were conducted at a pH value of 5, which was the maximum adsorption pH value for both metal ions. The equilibrium studies were investigated at a varying initial concentration (10-200 mg/L) with a constant dosage of 0.1 g, while the kinetic studies were conducted at a fixed initial concentration of 200 mg/L with a constant dosage of 1 g/L for both single and binary systems. The maximum adsorption capacity of the orange peel biochar was 28.06 mg/g, 26.83 mg/g, 30.12 mg/g and 27.71 mg/g for single Cu2+, binary Cu2+, single Pb2+ and binary Pb2+ systems, respectively. The Langmuir isotherm model fitted the experimental data, suggesting that adsorption occurred on a monolayer, while the pseudo-second-order model performed well with the kinetic data. The point of zero charge (pHpzc) of the orange peel biochar was found to be 10.03, which revealed that the surface of the bio-sorbent contains basic groups. A Fourier infrared transform (FTIR) spectroscope and scanning electron microscope, coupled with energy dispersive x-ray (SEM-EDX) and x-ray diffraction analyses, were used to determine the functional groups, surface morphology, and inorganic elements present on the surface of the bio-sorbent, respectively. The results obtained have shown that orange peel biochar is efficient for the removal of Cu2+ and Pb2+ ions from an aqueous solution.

Biogenic nanoparticles from waste fruit peels: Synthesis, applications, challenges and future perspectives

Nanotechnology is a continually growing field with a wide range of applications from food science to biotechnology and nanobiotechnology. As the current world is grappling with non-biodegradable waste, considered more challenging and expensive to dispose of than biodegradable waste, new technologies are needed today more than ever. Modern technologies, especially nanotechnology, can transform biodegradable waste into products for human use. Researchers are exploring sustainable pathways for nanotechnology by utilizing biodegradable waste as a source for preparing nanomaterials. Over the past ten years, the biogenic production of metallic nanoparticles (NPs) has become a promising alternative technique to traditional NPs synthesis due to its simplicity, eco-friendliness, and biocompatibility in nature. Fruit and vegetable waste (after industrial processing) contain various bioactives (such as flavonoids, phenols, tannins, steroids, triterpenoids, glycosides, anthocyanins, carotenoids, ellagitannins, vitamin C, and essential oils) serving as reducing and capping agents for NP synthesis and they possess antibacterial, antioxidant, and anti-inflammatory properties. This review addresses various sources of biogenic NPs including their synthesis using fruit/vegetable waste, types of biogenic NPs, extraction processes and extracted biomaterials, the pharmacological functionality of NPs, industrial aspects, and future perspectives. In this manner, this review will cover the most recent research on the biogenic synthesis of NPs from fruit/vegetable peels to transform them into therapeutic nanomedicines.

Evaluation of nutritional profile, phytochemical potential, functional properties and anti-nutritional studies of Citrus limetta peels

The aim of this work was to determine the proximate, mineral, amino acid composition, antioxidant activity, anti-nutritional factors, total dietary fiber, total phenolic content and technological properties of C. limetta peels. Moreover, analytical techniques including FT-IR and SEM were also conducted to study the morphological and structural properties of C. limetta peels. Considering the proximate, mineral, and amino acid composition, C. limetta peels was found to be a good source of ash (3.06 ± 0.20%), crude fiber (10.13 ± 0.30%), carbohydrate (64.08 ± 0.55%), protein (7.56 ± 0.25%), potassium (125.9671 mg/100 g), calcium (112.5861 mg/100 g), magnesium (16.43 mg/100 g), asparagine (2111.06 nmol/mg), glutamic acid (1331.96 nmol/g), and aspartic acid (1162.19 nmol/mg). Furthermore, they contain an appreciable amount of total dietary fiber (48.73 ± 0.45%), total phenolic content (14.30 ± 0.03 mg GAE/g), and antioxidant activity (52.65 ± 0.10%). Moreover, the antinutritional factors present in C. limetta peels were observed to be within the threshold limit. The results of technological properties of peels suggested that they can be potentially utilized as good emulsifying, gelling, foaming, and bulking agents in food industries. Therefore, C. limetta peels can be successfully re-utilized as natural food additive with numerous nutritive and bioactive properties in food sector, thereby achieving zero waste generation.

Modified biochar prepared from Retinervus luffae fructus for dyes adsorption and aerobic sludge granulation

Retinervus luffae fructus biochar (RLFB) and ZnCl2 pretreated Retinervus luffae fructus biochar (ZRLFB) were prepared by pyrolysis. The as-prepared biochar was investigated for its applicability as a dye adsorber using sunset yellow (SY) and basic red 46 (BR46) dyes. Additionally, ZRLFB was used for the experimental cultivation of granular sludge. The results indicated that the adsorption effect of ZRLFB on the two dyes was higher than RLFB. The adsorption of RLFB to SY was related to the Langmuir and Freundlich models, whereas the adsorption of RLFB-BR46, ZRLFB-SY, and ZRLFB-BR46 was more in line with the Langmuir model. The adsorption process of dyes on two kinds of biochars can be described using pseudo-second-order mechanisms. The maximum adsorption capacity obtained was 1.9586 (RLFB-SY), 6.1286 (RLFB-BR46), 49.2611 (ZRLFB-SY), and 181.4882 mg g^-1 (RLFB-BR46). The result of the SBR operation showed that ZRLFB can potentially be applied as the core of aerobic granular sludge.

Development of Rice Straw-derived Biochar-Bentonite Composite and its Application for in situ Sequestration of Ammonium and Phosphate Ions in the Degraded Mine Soil

Nutrient pollution has a diverse impact on the environment and human health. The presence of nutrients, such as ammonium and phosphate, is ubiquitous in the environment due to their extensive use in agricultural land and leaching through non-point sources. In this context, biochar-based composites could play an essential role in improving the soil's nutrient retention capacity. The present study aims to develop bentonite-biochar composites (BNT@BC 400 and 600) and utilize them as an ameliorating material in the coal mine degraded soil to reduce the leaching of ammonium and phosphate ions. The bentonite-biochar composite (BNT@BC 400 and 600) was synthesized using the pristine rice straw-derived biochar using the solvothermal method. The biochar was produced at two different pyrolytic temperatures, 400 °C and 600 °C, and denoted as BC 400 and 600, respectively. Hence, the bentonite-biochar composite was denoted as BNT@BC 400 and 600. The BNT@BC 400 and 600 were characterized using the elemental, proximate, SEM, XRD, and FTIR analysis. Subsequently, the BNT@BC composites were evaluated for the adsorptive removal of NH₄⁺ and PO₄^3- ions using batch adsorption and column leaching studies. In the soil columns, the BNT@BC 400 and 600 were mixed with the soil at two different application rates, viz. 1 and 2.5% (w/w). The leaching characteristics data were fitted using three different fixed-bed models to predict the maximum adsorption capacity of the amended soil columns and the dominant mechanism of adsorption. Results indicated that the BNT@BC 600 showed the maximum adsorption capacity of 33.77 and 64.23 mg g^-1 for the adsorption of NH₄⁺ and PO₄^3- ions, respectively. The dominant adsorption mechanisms in the aqueous solution were the electrostatic attraction, complexation, ion exchange, and precipitation processes. In the soil columns, the sorption of NH₄⁺ and PO₄^3- ions was governed by diffusive mass transfer and electrostatic interaction. Findings of the study indicated that incorporating the BNT@BC composite in the soil can significantly reduce the leaching of the NH₄⁺ and PO₄^3- ions and increase the overall soil fertility.

Type-wide biochars loaded with Mg/Al layered double hydroxide as adsorbent for phosphate and mixed heavy metal ions in water

This study discussed the adsorption of mixed heavy metal ions (Cu²⁺, Co²⁺, Pb²⁺) and phosphate ions by ten pristine biochars and those with precipitated Mg/Al layered double hydroxide (LDH). The pristine biochars have adsorption capacities of 6.9-13.4 mg/g for Cu²⁺, 1.1-9.7 mg/g for Co²⁺, 7.8-20.7 mg/g for Pb²⁺, and 0.8-4.9 mg/g for PO₄^3-. The LDH-biochars have markedly increased adsorption capacities of 20.4-25.8 mg/g for Cu²⁺, 8.6-15.0 mg/g for Co²⁺, 26.5-40.4 mg/g for Pb²⁺ with mixed metal ions, and 13.0-21.8 mg/g for PO₄^3-. Part of the Mg ions but Al ions are released from the LDH-biochars during adsorption, counting less than 7.2% of the adsorbed ions. The pristine biochars have specific adsorption sites for Cu²⁺ and Co²⁺, separate Pb²⁺ sites related to ether groups on biochar, and areal-dependent sites for PO₄^3-. There is no universal adsorption mechanism corresponding to mixed metal ion adsorption for individual pristine biochar involving different contributions of C-O-C, C-O-H, and CO groups and graphitic-N, pyrrolic-N, and pyridine-N groups. The LDH complexes with hydroxyl and carbonyl groups of biochar, and the LDH interacts with biochar's ether groups, which contributes to metal adsorption, against the conception that the biochar is merely a carrier of LDH as adsorbents.

Synthesis of NaA zeolite from foundry dust and its adsorption capacity of ammonia

Eutrophication of water bodies due to excess ammonia nitrogen (NH₄⁺-N) is harmful to aquatic organisms and human health. In this study, foundry dust (FD) from foundry industry was used to synthesize NaA zeolite to use as an adsorbent to remove NH₄⁺-N from wastewater. Results demonstrate that FD could be successfully synthesized to form a foundry dust-based NaA zeolite (FZA) through adjustment of the silica-alumina ratio of n (SiO₂)/n (Al₂O₃) at 2 at 95 °C. Specific surface area, total pore volume, and cation exchange capacity (CEC), and maximum adsorption NH₄⁺-N of FZA was respectively 43.185 cm²/g, 0.0364 cm³/g, 212.35 mmol/100 g and 37.81 mg/g, which was 4.74, 1.54, 1.52 and 1.62 times as much as the NaA zeolite (SZA). FZA with higher adsorption NH₄⁺-N capacity was related to higher specific surface area and CEC. The NH₄⁺-N adsorption amount of 28.57 mg/g by FZA was obtained after the fourth regeneration, which was notably higher than that of SZA (23.27 mg/g). The desorption rate of NH₄⁺-N from FZA was 87% by the fourth regeneration. FZA effectively removed NH₄⁺-N from swine wastewater containing 153.32 mg/L NH₄⁺-N. Results suggest that FZA could be used as absorbent to removal NH₄⁺-N from wastewater.

Nitrogen removal mechanisms in biochar-amended sand filters treating onsite wastewater

The performance of biochar-amended sand filters treating septic tank effluent (STE) was investigated in bench-scale columns. Softwood biochar showed higher NH₄ ⁺ -N adsorption capacity (1.3 mg N g^-1 ), and its water holding capacity (0.57 g ml^-1 ) was significantly higher than sand (0.26 g ml^-1 ). Two biochar amendment ratios (10% and 30%) were selected for STE treatment in short-term (20 days) and long-term (8 months) studies. During the short-term experiment, the overall total nitrogen removal efficiency was greater in biochar-amended sand columns (94.7%-95.6%) than in 100% sand columns (71.2%) due to the additional NH₄ ⁺ -N adsorption by biochar. Greater nitrification performance was also observed in biochar-amended columns (87.1%-96.3%) than in 100% sand columns (61.4%) during long-term operation when alkalinity was insufficient. The nitrification performance in biochar-amended columns resumed more quickly (<7 days) after sufficient alkalinity was amended. The density of total biomass and nitrifying bacteria in biochar-amended columns (30%) were significantly higher at all experimental stages, suggesting biochar served as a growth media for enhanced biomass growth. The alkalinity changes and STE composition fluctuation had little impact on the nitrification performance of the 30% biochar-amended sand columns. In addition, biochar surface functional groups and zeta potential changed little after long-term STE filtration. Collectively, the results demonstrated proper biochar amendment ratio (30%) could enhance the nitrification performance of sand filters treating STE by increasing the system hydraulic retention time, providing additional alkalinity for nitrification, and serving as a growth media for enhanced biomass growth.

Prosopis juliflora Seed Waste as Biochar for the Removal of Blue Methylene: A Thermodynamic and Kinetic Study

In this work, we studied the methylene blue (MB) dye adsorption capacity on biochar derived from residues of Prosopis juliflora seed waste, a species found in the region of the tropical dry forest of Piojó in the Department of Atlántico, Colombia. The materials were obtained by pyrolysis at temperatures of 300, 500, and 700 °C. Biochar was characterized using Fourier transform infrared (FTIR), scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDX), TGA, and Brunauer-Emmett-Teller (BET) techniques. The three biochar samples presented a macroporous, rough structure with pore size between 6 and 28 μm. The largest pore surface area observed was 1.28 m²/g for pyrolyzed biochar produced at 500 °C, larger than that of biochar produced at 700 °C, which was 0.83 m²/g. The adsorption results show that the maximum percentage of MB removal was 69%. According to SEM results, the material's pore sizes varied on average from 6 to 28 μm. We modeled MB adsorption on biomass through three different isotherm models. The Freundlich model was the best-fitting model for the removal of MB (K _F = 1.447; 1/n = 0.352). The kinetic results showed that the pseudo-second-order model was the best-fitting model for the sorption process (q _e = 2.94 mg/g; k ₂ = 0.087 g/(mg/min^-1)). Furthermore, the recycling test showed that the biochar did not change its adsorption capacity significantly. Finally, under the experimental conditions, the thermodynamic parameters indicated that the removal of MB using biochar was an endothermic and spontaneous process; all ΔG° values ranged from -2.14 to -0.95 kJ/mol; ΔH° was 23.54 kJ/mol and ΔS° was 79.5 J/mol.

Efficient adsorption of heavy metals from wastewater on nanocomposite beads prepared by chitosan and paper sludge

Chitosan was commonly used with inorganic salt and organic compounds to prepare adsorption material for water treatment. Different materials were mixed for the preparation, leading to a high cost for water treatment. Sludge from papermaking has abundant fiber and inorganic salt, which can reduce the addition of raw materials in preparing the adsorption material and thus lower the cost. This work used recycled industrial paper sludge to prepare adsorption material to remove heavy metals from wastewater. The adsorption properties of the prepared sludge-chitosan material for Cu²⁺ and Cr³⁺ in wastewater were investigated. The impacts of adsorption time, pH, and initial concentrations of Cu²⁺ and Cr³⁺ on adsorption amount were studied and optimized. The saturated adsorption capacity of sludge-chitosan material for Cu²⁺ and Cr³⁺ can reach 114.6 and 110.3 mg/g. The adsorption kinetics satisfied the pseudo-second-order model, indicating two modes, physical diffusion, and chem-sorption, in the heavy metal adsorption by the sludge-chitosan materials. Physical distribution has little Effect on chemical adsorption. The materials can be applied to treating Cu²⁺ and Cr³⁺ containing wastewater with the proposed cheap and readily available sludge-chitosan material. The results confirmed that sludge-chitosan material possessed good regeneration performance and was an ideal adsorbent.

From waste to fertilizer: Nutrient recovery from wastewater by pristine and engineered biochars

Biochar application for the recovery of nutrients from wastewater is a sustainable method based on a circular economy. Wastewater, food wastewater, and stormwater are valuable sources of nutrients (i.e., PO₄^3-, NO₃^-, and NH₄⁺). The unique properties of biochar, such as its large specific surface area, pH buffering capacity, and ion-exchange ability, make it a cost-effective and environmentally friendly adsorbent. Biochar engineering improves biochar properties and provide targeted adsorbents. The biochar-based fertilizers can be a sustainable alternative to traditional fertilization. The aim of the study was to compare the potential of pristine and engineered biochars to recover nutrients from wastewater and to determine the factors which may affect this process. Engineered biochar can be used as a selective adsorbent from multicomponent solutions. Adsorption on engineered biochar can be also regulated by additional mechanisms: surface precipitation and ligand/ion exchange. Metal modification (e.g. Mg, Fe) enhances PO₄^3- and NO₃^- adsorption capacity, and thus may provide the extra plant macro-/micronutrients. The desorption mechanism, which is the basis for nutrient release are strongly pH depended. The use of biochar-based fertilizer can have economic and agricultural benefits when using waste materials and reducing pyrolysis energy costs.

Pyrolysis of citrus wastes for the simultaneous production of adsorbents for Cu(II), H2, and d-limonene

A route based on pyrolysis and physical activation with H₂O and CO₂ was proposed to reuse citrus waste traditionally discarded. The citrus wastes were orange peel (OP), mandarine peel (MP), rangpur lime peel (RLP), and sweet lime peel (SLP). The main aim was to use the solid products of this new route as adsorbents for Cu(II) ions. Copper ions are among the most important water pollutants due to their non-degradability, toxicity, and bioaccumulation, facilitating their inclusion and long persistence in the food chain. Besides the solid products, the liquid and gaseous fractions were evaluated for possible applications. Results showed that the citrus waste composition favored the thermochemical treatment. In addition, the following yields were obtained from the pyrolysis process: approximately 30 % wt. of biochar, 40 % wt. of non-condensable gases, and 30 % wt. of bio-oil. The biochars did not present a high specific surface area. Nevertheless, activated carbons with CO₂ and H₂O presented specific surface areas of 212.4 m²/g and 399.4 m²/g, respectively, and reached Cu(II) adsorption capacities of 28.2 mg g^-1 and 27.8 mg g^-1. The adsorption kinetic study revealed that the equilibrium was attained at 60 min and the pseudo-second-order model presented a better fit to the experimental data. The main generated gases were CO₂, which could be employed as an activating agent for activated carbon production. d-limonene, used for food and medicinal purposes, was the main constituent of the bio-oil.

Nitrous oxide emission mitigation from biological wastewater treatment - A review

Nitrous oxide (N₂O) emitted from wastewater treatment processes has emerged as a focal point for academic and practical research amidst pressing environmental issues. This review presents an updated view on the biological pathways for N₂O production and consumption in addition to the critical process factors affecting N₂O emission. The current research trends including the strain and reactor aspects were then outlined with discussions. Last but not least, the research needs were proposed. The holistic life cycle assessment needs to be performed to evaluate the technical and economic feasibility of the proposed mitigation strategies or recovery options. This review also provides the background information for the proposed future research prospects on N₂O mitigation and recovery technologies. As pointed out, dilution effects of the produced N₂O gas product would hinder its use as renewable energy; instead, its use as an effective oxidizing agent is proposed as a promising recovery option.

A re-analysis of NH4+ sorption on biochar: Have expectations been too high?

Sorption of nutrients such as NH₄⁺ is often quoted as a critical property of biochar, explaining its value as a soil amendment and a filter material. However, published values for NH₄⁺ sorption to biochar vary by more than 3 orders of magnitude, without consensus as to the source of this variability. This lack of understanding greatly limits our ability to use quantitative sorption measurements towards product design. Here, our objective was to conduct a quantitative analysis of the sources of variability, and infer which biochar traits are more favourable to high sorption capacity. To do so, we conducted a standardized remodelling exercise of published batch sorption studies using Langmuir sorption isotherm. We excluded studies presenting datasets that either could not be reconciled with the standard Langmuir sorption isotherm or generated clear outliers. Our analysis indicates that the magnitude of sorption capacity of unmodified biochar for NH₄⁺ is lower than previously reported, with a median of 4.2 mg NH₄⁺ g^-1 and a maximum reported sorption capacity of 22.8 mg NH₄⁺ g^-1. Activation resulted in a significant relative improvement in sorption capacity, but absolute improvements remain modest, with a maximum reported sorption of 27.56 mg NH₄⁺ g^-1 for an activated biochar. Methodology appeared to substantially impact sorption estimates, especially practices such as pH control of batch sorption solution and ash removal. Our results highlight some significant challenges in the quantification of NH₄⁺ sorption by biochar and our curated data set provides a potentially valuable scale against which future estimates can be assessed.

Two-step ball milling-assisted synthesis of N-doped biochar loaded with ferrous sulfide for enhanced adsorptive removal of Cr(Ⅵ) and tetracycline from water

Nitrogen-doped biochar loaded with FeS (FeS@NBC_BM) was synthesized by two-step ball milling processes. Characterization results revealed that N-doping process successfully introduced pyridinic, pyrrolic, and graphitic N structures, and FeS was subsequently embedded in N-doped biochar (NBC_BM). The resultant FeS@NBC_BM presented predominant adsorption capacity for Cr(VI) (194.69 mg/g) and tetracycline (TC, 371.29 mg/g) compared with BC (27.28 and 37.89 mg/g) and NBC_BM (71.26 and 81.26 mg/g). In addition, the Cr(VI)/TC elimination process by FeS@NBC_BM was basically stable with multiple co-existing ions with slight decrease on adsorption performance after three desorption-regeneration cycles. Most importantly, FeS@NBC_BM was found to achieve Cr(VI) elimination not only by electrostatic attraction, ion exchange and complexation, but also by electrons-triggered reduction provided by different species of N, Fe²⁺ as well as S(Ⅱ). Meantime, pore filling, hydrogen bonding, and π-π stacking interactions were demonstrated to contribute to TC adsorption. These results suggested the co-modification of N-doping and FeS loading by ball milling as an innovative decorating method for biochar to adsorptive purification of Cr(VI) and TC-contaminated water.

Preparation and Characterization of Porous Materials from Pineapple Peel at Elevated Pyrolysis Temperatures

In this work, pineapple peel (PP) was reused as a precursor in biochar (BC) production at elevated temperatures (i.e., 500−900 °C) for residence times of 0−60 min. The findings showed that pyrolysis temperature and residence time played a vital role in pore development. As pyrolysis temperature increased from 800 to 900 °C for residence times of 20 and 60 min, the data on the Brunauer−Emmett−Teller (BET) surface area of the resulting biochar products significantly jumped from 11.98−32.34 to 119.43−133.40 m2/g. In addition, there was a significant increase in the BET surface area from 1.02 to 133.40 m2/g with the residence time of 0 to 20 min at 900 °C. From the data of the nitrogen adsorption−desorption isotherms and the pore size distribution, both micropores (pore diameters of <2.0 nm) and mesopores (pore diameters of 2.0−50.0 nm) are present in the PP-based biochar products. Due to its good fittings in the pseudo-second-order model and its hydrophilic nature, as seen in the Fourier transform infrared spectroscopy (FTIR), the resulting biochar could be a porous material to be used for the effective removal of cationic compounds (i.e., methylene blue (MB)) from liquid phases.

Recent advances in waste-derived functional materials for wastewater remediation

Water pollution is a major concern for public health and a sustainable future. It is urgent to purify wastewater with effective methods to ensure a clean water supply. Most wastewater remediation techniques rely heavily on functional materials, and cost-effective materials are thus highly favorable. Of great environmental and economic significance, developing waste-derived materials for wastewater remediation has undergone explosive growth recently. Herein, the applications of waste (e.g., biowastes, electronic wastes, and industrial wastes)-derived materials for wastewater purification are comprehensively reviewed. Sophisticated strategies for turning wastes into functional materials are firstly summarized, including pyrolysis and combustion, hydrothermal synthesis, sol-gel method, co-precipitation, and ball milling. Moreover, critical experimental parameters within different design strategies are discussed. Afterward, recent applications of waste-derived functional materials in adsorption, photocatalytic degradation, electrochemical treatment, and advanced oxidation processes (AOPs) are analyzed. We mainly focus on the development of efficient functional materials via regulating the internal and external characteristics of waste-derived materials, and the material's property-performance correlation is also emphasized. Finally, the key future perspectives in the field of waste-derived materials-driven water remediation are highlighted.

Application of biowaste generated by the production chain of pitaya fruit (Hylocereus undatus) as an efficient adsorbent for removal of naproxen in water

Pharmaceutical compounds are a serious problem in the environment. They cause damage to the aquatic, animal, and human organisms and soon became considered emerging pollutants where their removal is extremely urgent. Among the techniques used, adsorption has been used with success, where several adsorbent materials, including those from residual biomass, have been used to remove these pollutants. In this study, the skins of the pitaya fruit (Hylocereus undatus) productive chain were carbonized with ZnCl₂ to obtain activated carbon and later used in the adsorption of the drug naproxen (NPX) in a batch system. The Freundlich model demonstrated a better adjustment for the equilibrium isotherms. A high adsorption capacity for NPX (158.81 mg g^-1) was obtained at 328 K, which can be attributed to the remarkable textural properties of the adsorbent, besides certain functional groups present on its surface. Thermodynamic studies confirmed the endothermic nature of the adsorption process (∆H⁰ = 0.2898 kJ mol^-1). The linear driving force model (LDF) presented a good statistical adjustment to the experimental kinetic data. The application of the material in the treatment of simulated wastewater composed of various pharmaceutical drugs and salts was very promising, reaching 75.7% removal. Therefore, it can be inferred that the application of activated carbon derived from pitaya bark is highly promising in removing the NPX drug and treating synthetic mixtures containing other pharmaceutical substances.

Effects of competitive adsorption with Ni(II) and Cu(II) on the adsorption of Cd(II) by modified biochar co-aged with acidic soil

To investigate the effects of competitive adsorption with Ni(II) and Cu(II) on the adsorption of Cd(II) by modified biochar co-aged with acidic soil, four biochars were employed in this study, namely original biochar, KMnO₄-modified biochar and two aged biochars which co-aged with an acidic soil using above biochars under freeze-thaw cycling and dry-wet cycling for 54 days simulating 6 years of natural aging. The results showed that biochar adsorption capacities of three heavy metal ions were in the order of Cd(II) > Cu(II) > Ni(II) in the single system while Cu(II) > Cd(II) > Ni(II) in binary and ternary systems. Modification improved biochar adsorption capacity of Cd(II), but competitive adsorption with Ni(II) and Cu(II) weakened the improvement of modification on adsorption performance of modified biochar in binary and ternary systems. The Q_MBC/Q_BC of Cd(II) (Q_MBC and Q_BC are the adsorption capacities of heavy metals by modified and original biochars) decreased from 231.57% (single system) to 216.67%∼219.41% (binary system) and further decreased to 207.74% (ternary system). Co-aging with soil weakened the adsorption capacities of biochars for Cd(II), even worse, competition aggravated this negative effect of co-aging. The Q_AMBC/Q_MBC of Cd(II) (Q_AMBC is the adsorption capacities of heavy metals by aged modified biochar) decreased from 65.41% (single system) to 14.43%∼19.46% (binary and ternary systems). Therefore, the impact of competition should be fully considered when evaluating Cd long-term remediation effects of modified biochar in Cd polluted soils accompanied with other heavy metals.

Enhancement of urea removal from reclaimed water using thermally modified spent coffee ground biochar activated by adding peroxymonosulfate for ultrapure water production

To enhance the degradation of urea in reclaimed water for producing ultrapure water (UPW), thermally modified biochar (TBC) was prepared by secondary pyrolysis using spent coffee biochar with the function as an activator of peroxymonosulfate (PMS). Results showed that 94.4% of urea can be degraded effectively by the TBC-PMS system at the dosage of 0.4 g/L TBC and 2 g/L PMS under neutral and weak acid conditions. Moreover, urea removal mainly depended on the free radical pathway (SO₄^{• -} and OH^•), especially OH^•. The inorganic anions of TBC increased via secondary pyrolysis, especially carbonate and phosphate, resulting in higher electrical conductance (EC) value than the original biochar. It was conducive to activating PMS. As well, C-O, -OH worked as an active site in the TBC-PMS system, providing electrons and activating PMS. This work provides a novel strategy for UPW production using TBC-PMS system.

Sorption, separation and recycling of ammonium in agricultural soils: A viable application for magnetic biochar?

Recent research on the magnetisation of biochar, a carbon-based material that can be used as a sorbent, has opened novel opportunities in the field of environmental remediation, as incorporating magnetic particles into biochar can simplify subsequent separation. This could offer a sustainable circular economy-based solution in two areas of waste management; firstly, pyrolysis of agricultural waste for magnetic biochar synthesis could reduce greenhouse gas emissions derived from traditional agricultural waste processing, such as landfill and incineration, while secondly, application of magnetic biochar to remove excess nitrogen from soils (made possible through magnetic separation) could provide opportunities for this pollutant to be used as a recycled fertiliser. While sorption of pollutants by magnetic biochar has been researched in wastewater, few studies have investigated magnetic biochar use in polluted soils. Nitrogen pollution (e.g. NH₄⁺), stemming from agricultural fertiliser management, is a major environmental and economic issue that could be significantly reduced before losses from soils occur. This review demonstrates that the use of magnetic biochar tailored to NH₄⁺ adsorption has potential to remove (and recycle for reuse) excess nitrogen from soils. Analysis of research into recovery of NH₄⁺ by sorption/desorption, biochar magnetisation and biochar-soil interactions, suggests that this is a promising application, but a more cohesive, interdisciplinary approach is called for to elucidate its feasibility. Furthermore, research shows variable impacts of biochar upon soil chemistry and biology, such as pH and microbial diversity. Considering wide concerns surrounding global biodiversity depletion, a more comprehensive understanding of biochar-soil dynamics is required to protect and support soil ecosystems. Finally, addressing research gaps, such as optimisation and scaling-up of magnetic biochar synthesis, would benefit from systems thinking approaches, ensuring the many complex considerations across science, industry, policy and economics are connected by circular-economy principles.

Using raw and thermally modified fibrous clay minerals as low concentration NH4+-N adsorbents

Raw and modified fibrous clay minerals palygorskite (Pal) and sepiolite (Sep) were tested for their ability to remove ammonium from ammonium polluted water. Palygorskite and sepiolite underwent thermal treatment at 400°C (T-Pal and T-Sep respectively). Raw and thermally treated samples were characterized using XRD, SEM, BET, FTIR, TGA, zeta potential, and XRF. The techniques verified the effect of thermal treatment on sample structures and the enhancement of negative charge. Both raw and thermally activated materials were applied in batch kinetic experiments, and found to be efficient adsorbents in their raw forms, since Pal and Sep achieved 60 and 80% NH₄⁺-N removal respectively within 20 min of contact for initial NH₄⁺-N concentration of 4 mg/L. Similar removal rates were gained for other concentrations representative of contaminated aquifers that were examined, ranging from 1 to 8 mg/L. Results for the modified T-Pal and T-Sep minerals showed up to 20% higher removal rate. Saturation tests indicated the positive effect of thermal treatment on the minerals since T-Pal and T-Sep removal efficiency reached 85% and remained stable for 24 h. However, competitive ions in real water samples can influence the NH₄⁺-N removal efficiency of the examined samples. At almost all the examined samples, the nonlinear Freundlich isotherm and linear pseudo-second kinetic models showed better fitted all examined samples thus indicating heterogeneous chemisorption.

Recent advancements on biochars enrichment with ammonium and nitrates from wastewaters: A critical review on benefits for environment and agriculture

During the last decade, biochars have been considered as attractive and eco-friendly materials with various applications including wastewater treatment, energy production and soil amendments. However, the important nitrogen losses during biochars production using the pyrolysis process have limited their potential use in agriculture as biofertilizer. Therefore, it seems necessary to enrich these biochars with nitrogen sources before their use in agricultural soils. This paper is the first comprehensive review on the assessment of biomass type and the biochars' properties effects on N recovery efficiency from aqueous solutions as well as its release and availability for plants when applying the N-enriched chars in soils. In particular, the N recovery efficiency by raw biochars versus the type of the raw feedstock is summarized. Then, correlations between the adsorption performance and the main physico-chemical properties are established. The main mechanisms involved during ammonium (NH₄-N) and nitrates (NO₃-N) recovery process are thoroughly discussed. A special attention is given to the assessment of the biochars physico-chemical modification impact on their N recovery capacities improvement. After that, the application of these N-enriched biochars in agriculture and their impacts on plants growth as well as methane and nitrous oxide greenhouse gas emissions reduction are also discussed. Finally, the main future development and challenges of biochars enrichment with N from wastewaters and their valorization as biofertilizers for plants growth and greenhouse gas (GHG) emissions reduction are provided. This systematic review is intended to promote the real application of biochars for nutrients recovery from wastewaters and their reuse as eco-friendly fertilizers.

A new spent coffee grounds based biochar - Persulfate catalytic system for enhancement of urea removal in reclaimed water for ultrapure water production

The demand for ultrapure water (UPW) in the semiconductor industry has increased in recent years, while the idea to use reclaimed water instead of tap water for UPW production has also attracted more attention. However, since urea concentration in reclaimed water is higher than that in tap water, UPW production has not been efficient. To resolve this problem, this study aims to develop a new spent coffee grounds based biochar (SCG-BC)/persulfate catalytic system as a pretreatment unit. The objective is to enhance urea removal from reclaimed water so that UPW production is more effective. In this study, the biochar used was prepared from spent coffee grounds with detailed characterization. Results strongly suggested that the urea removed by SCG-BC/persulfate catalytic system was very encouraging (up to 73%). The best possible dosages for SCG-BC and persulfate for urea removal were 0.2 and 2.0 g L^-1, respectively. Furthermore, this system could remove urea effectively in a wide range of pH (3-10). Moreover, the characterizations of SCG-BC (graphite C, defective edges and functional groups, i.e. -OH, CO, carboxyl C-O) helped to activate persulfate in the catalytic process. OH^• and SO₄^• - were all involved in this process, while the SO₄^• - was the main radical for urea degradation.

Magnetic-watermelon rinds biochar for uranium-contaminated water treatment using an electromagnetic semi-batch column with removal mechanistic investigations

Biosorption using modified biochar has been increasingly adopted for the sustainable removal of uranium-contaminated from an aqueous solution. In this research study, the facile preparation and surface characteristics of magnetized biochar derived from waste watermelon rind to treat U(VI) contaminated water were investigated. The porosity, specific surface area, adsorption capacity, reusability, and stability were effectively improved after the magnetization of biochar. The kinetics and isotherm studies found that the U(VI) adsorption was rate-limiting monolayer sorption on the homogeneous surface of magnetized watermelon rind biochar (MWBC). The maximum adsorption capacity was found to be 323.56 mg of U(VI) per g of MWBC at pH 4.0 and 293 K that was higher than that of watermelon rind biochar (WBC) (135.86 mg g^-1) and other sourced biochars. The surface interaction mechanism, environmental feasibility, applicability for real-filed water treatment studied in the electromagnetic semi-batch column, and reusability of MWBC were also explored. Furthermore, salient raised the ion exchange and complexation action capacity of MWBC due to the presence of Fe oxide. The overall results indicated that MWBC was not only inexpensive and had a high removal capacity for U(VI), but it also easily enabled phase separation from an aqueous solution, with more than three times reusability at a minimum removal capacity of 99%.