Adsorption removal of ibuprofen and naproxen from aqueous solution with Cu-doped Mil-101(Fe)

Management of ibuprofen in wastewater using electrospun nanofibers developed from PET and PS wastes

Electrospinning is a promising technique for the beneficial use and recycling of plastic waste polymers using simple methodologies. In this study, plastic bottles and Styrofoam wastes have been used to develop polyethylene terephthalate (PET) and polystyrene (PS) nanofibers using electrospinning technique separately without any further purification. The effect of the concentration onto the nanofiber's morphology was studied. The fabricated nanofibers were characterized using Field Emission Scanning Electron Microscope (FE-SEM), Fourier Transformed Infrared Spectroscopy (ATR-FTIR), N2 adsorption/desorption analysis, and water contact angle (WCA). Furthermore, the prepared nanofibers were applied for the adsorption of ibuprofen (IBU) from wastewater. Some parameters that can influence the adsorption efficiency of nanofibers such as solution pH, wt.% of prepared nanofibers, drug initial concentration, and contact time were studied and optimized. The results show that the equilibrium adsorption capacity was achieved after only 10 min for 12 wt% PET nanofibers which is equivalent to 364.83 mg/g. For 12 wt% PS nanofibers, an equilibrium adsorption capacity of 328.42 mg/g was achieved in 30 min. The experimental data was fitted to five isotherm and four kinetics models to understand the complicated interaction between the nanofibers and the drug. Langmuir-Freundlich isotherm model showed the best fit for experimental data for both PET and PS nanofibers. The adsorption process was characterized by predominantly physical reaction rather than chemical adsorption for both materials. The reusability study revealed that the synthesized nanofibers maintain their ability to adsorb/desorb IBU for up to five cycles. The results obtained demonstrated that fabricated nanofibers from plastic wastes could perform promising adsorbents for the management of IBU in wastewater. However, further research is needed for the scaling-up the fabrication which is required for real-world applications.

Pharmaceutically active compounds removal from aqueous solutions by MIL-101(Cr)-NH2: A molecular dynamics study

Discharging pharmaceutically active drugs into water and wastewater has become a significant environmental threat. Traditional methods are unable to effectively remove these compounds from wastewater, so it is necessary to search for more effective methods. This study investigates the potential of MIL-101(Cr)-NH2 as a preferable and more effective adsorbent for the adsorption and removal of pharmaceutically active compounds from aqueous solutions. By utilizing its large porosity, high specific surface area, and high stability, the structural and transport properties of three pharmaceutically active compounds naproxen (NAP), diclofenac (DIC) and sulfamethoxazole (SMX)) studied using molecular dynamics simulation. The results indicate that the MIL-101(Cr)-NH2 adsorbent is suitable for removing drug molecules from aqueous solutions, with maximum adsorption capacities of 697.75 mg/g for naproxen, 704.99 mg/g for diclofenac, and 725.51 mg/g for sulfamethoxazole.

Innovations in metal-organic frameworks (MOFs): Pioneering adsorption approaches for persistent organic pollutant (POP) removal

Adsorption is a promising way to remove persistent organic pollutants (POPs), a major environmental issue. With their high porosity and vast surface areas, MOFs are suited for POP removal due to their excellent adsorption capabilities. This review addresses the intricate principles of MOF-mediated adsorption and helps to future attempts to mitigate organic water pollution. This review examines the complicated concepts of MOF-mediated adsorption, including MOF synthesis methodologies, adsorption mechanisms, and material tunability and adaptability. MOFs' ability to adsorb POPs via electrostatic forces, acid-base interactions, hydrogen bonds, and pi-pi interactions is elaborated. This review demonstrates its versatility in eliminating many types of contaminants. Functionalizing, adding metal nanoparticles, or changing MOFs after they are created can improve their performance and remove contaminants. This paper also discusses MOF-based pollutant removal issues and future prospects, including adsorption capacity, selectivity, scale-up for practical application, stability, and recovery. These obstacles can be overcome by rationally designing MOFs, developing composite materials, and improving material production and characterization. Overall, MOF technology research and innovation hold considerable promise for environmental pollution solutions and sustainable remediation. Desorption and regeneration in MOFs are also included in the review, along with methods for improving pollutant removal efficiency and sustainability. Case studies of effective MOF regeneration and scaling up for practical deployment are discussed, along with future ideas for addressing these hurdles.

Recent advances and potential applications for metal-organic framework (MOFs) and MOFs-derived materials: Characterizations and antimicrobial activities

Microbial infections, particularly those caused by antibiotic-resistant pathogens, pose a critical global health threat. Metal-Organic Frameworks (MOFs), porous crystalline structures built from metal ions and organic linkers, initially developed for gas adsorption, have emerged as promising alternatives to traditional antibiotics. This review, covering research up to 2023, explores the potential of MOFs and MOF-based materials as broad-spectrum antimicrobial agents against bacteria, viruses, fungi, and even parasites. It delves into the historical context of antimicrobial agents, recent advancements in MOF research, and the diverse synthesis techniques employed for their production. Furthermore, the review comprehensively analyzes the mechanisms of action by which MOFs combat various microbial threats. By highlighting the vast potential of MOFs, their diverse synthesis methods, and their effectiveness against various pathogens, this study underscores their potential as a novel solution to the growing challenge of antibiotic resistance.

Wood-converted porous carbon decorated with MIL-101(Fe) derivatives for promoting photo-Fenton degradation of ciprofloxacin

In response to the escalating concerns over antibiotics in aquatic environments, the photo-Fenton reaction has been spotlighted as a promising approach to address this issue. Herein, a novel heterogeneous photo-Fenton catalyst (Fe3O4/WPC) with magnetic recyclability was synthesized through a facile two-step process that included in situ growth and subsequent carbonization treatment. This catalyst was utilized to expedite the photocatalytic decomposition of ciprofloxacin (CIP) assisted by H2O2. Characterization results indicated the successful anchoring of MIL-101(Fe)-derived spindle-like Fe3O4 particles in the multi-channeled wood-converted porous carbon (WPC) scaffold. The as-synthesized hybrid photocatalysts, boasting a substantial specific surface area of 414.90 m2·g-1 and an excellent photocurrent density of 0.79 μA·cm-2, demonstrated superior photo-Fenton activity, accomplishing approximately 100% degradation of CIP within 120 min of ultraviolet-light exposure. This can be attributed to the existence of a heterojunction between Fe3O4 and WPC substrate that promotes the migration and enhances the efficient separation of photogenerated electron-hole pairs. Meanwhile, the Fe(III)/Fe(II) redox circulation and mesoporous wood carbon in the catalyst synergistically enhance the utilization of H2O and accelerate the formation of •OH radicals, leading to heightened degradation efficiency of CIP. Experiments utilizing chemical trapping techniques have demonstrated that •OH radicals are instrumental in the CIP degradation process. Furthermore, the study on reusability indicated that the efficiency in removing CIP remained at 89.5% even through five successive cycles, indicating the structural stability and excellent recyclability of Fe3O4/WPC. This research presented a novel pathway for designing magnetically reusable MOFs/wood-derived composites as photo-Fenton catalysts for actual wastewater treatment.

Degradation of Orange G Using PMS Triggered by NH2-MIL-101(Fe): An Amino-Functionalized Metal-Organic Framework

As an azo dye, OG has toxic and harmful effects on ecosystems. Therefore, there is an urgent need to develop a green, environmentally friendly, and efficient catalyst to activate peroxymonosulfate (PMS) for the degradation of OG. In this study, the catalysts MIL-101(Fe) and NH2-MIL-101(Fe) were prepared using a solvothermal method to carry out degradation experiments. They were characterized by means of XRD, SEM, XPS, and FT-IR, and the results showed that the catalysts were successfully prepared. Then, a catalyst/PMS system was constructed, and the effects of different reaction systems, initial pH, temperature, catalyst dosing, PMS concentration, and the anion effect on the degradation of OG were investigated. Under specific conditions (100 mL OG solution with a concentration of 50 mg/L, pH = 7.3, temperature = 25 °C, 1 mL PMS solution with a concentration of 100 mmol/L, and a catalyst dosage of 0.02 g), the degradation of OG with MIL-101(Fe) was only 36.6% within 60 min; as a comparison, NH2-MIL-101(Fe) could reach up to 97.9%, with a reaction constant k value of 0.07245 min-1. The NH2-MIL-101 (Fe)/PMS reaction system was able to achieve efficient degradation of OG at different pH values (pH = 3~9). The degradation mechanism was analyzed using free-radical quenching tests. The free-radical quenching tests showed that SO4•-, •OH, and 1O2 were the main active species during the degradation of OG.

MIL-53(Al)@HC nanohybrid for bicomponent adsorption of ibuprofen and metsulfuron-methyl: Application of macro- and microscopic models and competition between contaminants

In this work, a hybrid was synthesized by hydrothermal treatment, metal-organic framework functionalized with hydrochar (MIL-53(Al)@HC) for the adsorption of two organic molecules Ibuprofen sodium salt and Metsulfuron-methyl, in binary system. The hybrid is composed of 71 wt% biomass and 29 wt% MOF. TGA, BET, FTIR, XRD and XPS characterization techniques were used to verify the hybridization of MIL-53(Al)@HC. The MIL-53(Al)@HC hybrid showed in situ MIL-53(Al) crystal growth capability. Batch adsorption experiments were carried out to study the effect of pH, adsorbent dosage, adsorbate concentration, contact time and temperature effect. The results obtained under extreme conditions demonstrate that MIL-53(Al)@HC is an adsorbent capable of removing >98% of IBU and MTM in mixture at a concentration of 0.3 mM (68 ppm IBU and 115 ppm MTM). The pseudo-second order model adequately described the adsorption kinetics and equilibrium using the Sips and Freundlich models. The physico-statistical microscopic model (2-layer) corroborated the hypothesis of a multilayer adsorption proposed by the macroscopic Freundlich model. In the competition study between IBU and MTM, both antagonistic and synergistic effects were observed. In the thermodynamic study, positive values of (ΔH°) indicate that adsorption is endothermic in nature and that the dominant mechanism is physisorption. A mechanism of adsorption by hydrogen bridging and non-covalent π*-π adsorbate-adsorbate and adsorbate-adsorbate-adsorbate interactions was proposed. The desorption study shows that in 5 washing cycles MIL-53(Al)@HC is a recoverable material.

Non-steroidal anti-inflammatory drugs (NSAIDs) in the environment: Recent updates on the occurrence, fate, hazards and removal technologies

Non-steroidal Anti-inflammatory Drugs (NSAIDs) are extensively utilized pharmaceuticals worldwide. However, owing to the improper discharge and disposal practices, they have emerged as significant contaminants that are widely distributed in water, soils, and sewage sediments. This ubiquity poses a substantial threat to the ecosystem and human health. Consequently, it is imperative to develop rapid, cost-effective, efficient and reliable approaches for containing these substance in order to mitigate the deleterious impact of NSAIDs. This research provides a comprehensive review of the occurrence, fate, and hazards associated with NSAIDs in the general environment. Additionally, various removal technologies, including advanced oxidation processes, biodegradation, and adsorption, were systematically summarized. The study also presents a comparative analysis of the benefits and drawbacks of different removal technologies while interpreting challenges related to NSAIDs' removal and proposing strategies for future development.

Preparation of metal-organic framework @molecularly imprinted polymers for extracting N-nitrosamines in salted vegetables

In this paper, the novel metal-organic framework @molecularly imprinted polymers were prepared and applied in extracting N-nitrosamines from salted vegetables. The imprinted polymers were coated on the surface of MIL-101 using multi-dummy template molecules (5-nonanol, benzhydrol and N-formylpyrrolidine). The characterization and adsorbing experiments showed that the hybrid imprinted polymers presented spherical particles with typically core-shell structure, and exhibited high adsorption capacity (maximum capacity: 46.85 mg/g) and fast equilibrium rate (only 5 min) for N-nitrosamines. Various parameters (sample loading solvent, pH, washing solvent, elution solvent and elution volume) affecting solid-phase extraction were optimized. Under the optimum conditions, the solid-phase extraction process based on the hybrid polymers combined with high performance liquid chromatography-ultraviolet detection method was established and applied to analyze N-nitrosamines in different salted vegetables. The results showed that the developed method produced the linear relationship between the peak areas versus the N-nitrosamines concentrations of 0.2-10 µg/g with limit of detections from 20.6 to 76.1 ng/g. The spiked recovery of N-nitrosamines in the salted vegetable samples was in the range of 66-100.5 % with relative standard deviation from 0.1 to 3.4 %. Those results demonstrated that the established method was sensitive and efficient for directly enriching and analyzing trace N-nitrosamines in salted vegetables.

Occurrence, toxicity, impact and removal of selected non-steroidal anti-inflammatory drugs (NSAIDs): A review

Non-steroidal anti-inflammatory drugs (NSAIDs) are among the most frequently used pharmaceuticals for human therapy, pet therapeutics, and veterinary feeds, enabling them to enter into water sources such as wastewater, soil and sediment, and seawater. The control of NSAIDs has led to the advent of the novel materials for treatment techniques. Herein, we review the occurrence, impact and toxicity of NSAIDs against aquatic microorganisms, plants and humans. Typical NSAIDs, e.g., ibuprofen, ketoprofen, diclofenac, naproxen and aspirin were detected at high concentrations in wastewater up to 2,747,000 ng L-1. NSAIDs in water could cause genotoxicity, endocrine disruption, locomotive disorders, body deformations, organs damage, and photosynthetic corruption. Considering treatment methods, among adsorbents for removal of NSAIDs from water, metal-organic frameworks (10.7-638 mg g-1) and advanced porous carbons (7.4-400 mg g-1) were the most robust. Therefore, these carbon-based adsorbents showed promise in efficiency for the treatment of NSAIDs.

Metal-organic frameworks modified melamine foam in pipette-tip for rapid solid-phase extraction of organophosphorus pesticides in fruits and vegetables

In this work, metal-organic frameworks (MOFs) including Fe-MIL-101 and Ti-MIL-125 were prepared and fixed on the melamine foam (MF) by polyvinylidene fluoride (PVDF) to prepare MF/PVDF/MOFs, which was used as adsorbents in pipette-tip solid-phase extraction (PT-SPE) for rapid extraction of organophosphorus pesticides (OPPs). Then, a gas chromatograph-flame thermionic detector (GC-FTD) was used for simultaneous analysis of Dimethoate (DMT), Iprobenfos (IBF), Parathion-methyl (PAM), and Chlorpyrifos (CPF). The morphology, crystal structure, and functional groups of MF/PVDF/MOFs were characterized, indicating that Ti-MIL-125 and Fe-MIL-101 were successfully synthesized and distributed on MF. The Fe-MIL-101 and Ti-MIL-125 showed good extraction ability for OPPs, which was mainly due to the π-π interaction and the multiple porous structures. Under the optimal conditions, the limit of detection (LODs) of four OPPs was 0.03-0.14 μg L-1 and the RSDs were less than 9.9%. The developed PT-SPE method showed a short extraction time (<3 min). The recoveries in fruits and vegetables (Celery, cabbages, and oranges) ranged from 75.3%-118.8% (RSDs<9.6%). The prepared MF/PVDF/MOFs demonstrated the efficient extraction performance of OPPs, contributing to the rapid pretreatment of OPPs from food and the environment.

Characterization of an Iron-Copper Bimetallic Metal-Organic Framework for Adsorption of Methyl Orange in Aqueous Solution

Iron-based organic frame material MIL-53 (Fe) was synthesized by the hydrothermal method with Cu2+ incorporated to obtain bimetallic composite MIL-53 (Fe, Cu). The structure and morphology of the material were characterized by SEM, XRD, BET, FTIR, XPS, and zeta potential. The adsorption performance of MIL-53 (Fe, Cu) on methyl orange was tested under a variety of conditions, including the effects of pH and material dosage, by the static adsorption test. The results show that under the condition of pH = 7, a temperature of 30°C, and an adsorbent dosage of 20 mg, the removal rate of MIL-53 (Fe, Cu) for methyl orange can reach more than 96% within 4 h, and the maximum adsorption capacity after fitting by the thermodynamic model can reach 294.43 mg/g, showing the excellent adsorption performance of MIL-53 (Fe, Cu) on methyl orange. In addition, by exploring the adsorption mechanism of MIL-53 (Fe, Cu) on methyl orange, it is found that the adsorption of MIL-53 (Fe, Cu) on methyl orange depends on chemical adsorption, as evidenced by combining Fe3+ and Cu2+ in the material with methyl orange molecules to form complexes to achieve adsorption. While the specific surface area of the material had no obvious effect on adsorption, the effects of pH, temperature, and concentration were explored. At a pH of 6.5, greater adsorption occurred at higher temperatures, as determined by thermodynamic model fitting, as well as with higher initial methyl orange molecule concentration.

Polyaniline-modified halloysite nanotubes as high-efficiency adsorbents for removing of naproxen in the presence of different heavy metals

In this work, novel adsorbent polyaniline-modified halloysite nanotubes (HNT@PA-2) were synthesized successfully by in situ polymerization to increase active adsorption sites. With the increase of the amount of aniline, the adsorption capacity of naproxen becomes higher. The optimal ratio of halloysite nanotubes to aniline was 1 : 2. The effects of adsorption conditions such as pH, mass of HNT@PA-2, time and initial concentration of naproxen were systematically researched. The optimum adsorption for naproxen was pH 9, mass 10 mg and contact time 4 h. The adsorption of naproxen conformed to the pseudo-first-order kinetic model, and the maximum adsorption capacity was 242.58 mg g-1 at 318 K. In addition, the effects of ionic strength and different heavy metals also were studied. Higher ionic strength of the system could influence the adsorption of naproxen. The effects of Al3+, Pb2+, Zn2+ and Co2+ ions on the adsorption of naproxen could be ignored, while Cu2+ and Fe3+ ions inhibited the process. The mechanisms for naproxen adsorbed by the HNT@PA-2 were π-π interaction, hydrogen bonding and hydrophobic reaction. Therefore, the HNT@PA-2 could be used for the treatment of medical wastewater for removing naproxen.

Activation of peroxymonosulfate for degrading ibuprofen via single atom Cu anchored by carbon skeleton and chlorine atom: The radical and non-radical pathways

Single atomic Cu catalysts (SACs Cu@C) anchored by carbon skeleton and chlorine atom was synthesized by hydrolyzing Cu-MOFs and then pickled by aqua-regia to remove Cu nanoparticles (NPs Cu). Comparative characterizations revealed that SACs Cu@C was a hierarchically porous nanostructure and Cu dispersed uniformly throughout the carbon skeletons. With less active components, SACs Cu@C behaved better in activating PMS over NPs Cu@C on ibuprofen removal (91.3 % versus 30.2 % in 30 min). Two Cu coordination environments were found by EXAF and DFT calculation, including four-coordinated Cu with 4C atoms and six-coordinated Cu with 4Cu and 2Cl atoms. The obvious interfacial electron delivery between PMS and SACs Cu@C was found, which was enhanced by Cl atom. Cu(I)/Cu(II) redox cycle would donate electron to peroxy bond of PMS for generating OH, SO₄^- and O₂^-. But electron transferred in opposite direction when PMS bonded to Cu atom through its terminal oxygen atom in sulfate, which formed ¹O₂. IBP degradation proceeded through both radical and non-radical route. IBP degradation was inhibited with the presence of TBA, methanol and furfuryl alcohol but accelerated by p-BQ, which could accelerate OH generation. Two degradation pathways were deducted. This study provided a new insight into catalysts designed for PMS activation.

Characterization of ibuprofen removal by calcined spherical hydrochar through adsorption experiments, molecular modeling, and artificial neural network predictions

Ibuprofen (IPF) is one of the most prescribed nonsteroidal anti-inflammatory drugs in recent times, but it is not readily removed in conventional wastewater treatments. Here, we investigate the adsorption characteristics of IPF onto calcined spherical hydrochar (CSH), which was synthesized through hydrothermal carbonization of sucrose followed by calcination. The adsorption experiments show that the equilibration time for IPF was 360 min, and a pseudo-second-order model was best fitted to the kinetic data. The isotherm data were best described by the Liu model with a theoretical maximum adsorption capacity of 95.6 mg/g. The thermodynamic data indicate the endothermic nature of the adsorption at 10-40 °C. The CSH was favorably regenerated and reused using methanol. In pH experiments, the IPF adsorption capacity declined gradually as pH rose from 2 to 8, dropped rapidly at pH 10, and became negligible at pH 12. The IPF adsorption to the CSH could occur through various adsorption mechanisms. Hydrogen-bond formation, π-π interactions, n-π* interactions, and electrostatic repulsion were explored and visualized with molecular modeling using CHEM3D. The Raman, FTIR, and XPS spectra suggest that π-π interactions could take place between the CSH and IPF. Considering the pK_a value of IPF (4.91) and pH_iep of the CSH (3.21), electrostatic repulsion between the negatively-charged CSH and anionic IPF could play a negative role in the adsorption. A pore-filling mechanism could contribute to the adsorption in view of the molecular size of IPF (9.43 Å × 7.75 Å × 6.23 Å) and the average pore diameter of the CSH (2.27 nm). In addition, hydrophobic interactions could be involved in the adsorption. Multi-factor adsorption experiments were executed with pH, temperature, CSH dosage, and initial IPF concentrations as input variables and IPF removal rate as an output variable, and an artificial neural network (ANN) model with a topology of 4:9:11:1 was developed to sufficiently describe the adsorption data (R > 0.99). Further analyses with additional experimental data confirm that the ANN model possessed good predictability for multi-factor adsorption.

The growth, biochemical composition, and antioxidant response of Microcystis and Chlorella are influenced by Ibuprofen

Non-steroidal anti-inflammatory drugs like ibuprofen (IBU) are extensively used, causing substantial amounts to end up in aquatic ecosystems. Unfortunately, little research has been done on how these medications influence the physiology of phytoplankton. This study aimed to investigate the toxicological and physiological effects of IBU on the cyanobacteria Microcystis aeruginosa LE3 and Microcystis aeruginosa EAWAG 198, and the chlorophyte Chlorella sorokiniana. Exponential growth phase cultures were exposed to IBU at 10 to 10,000 μg/L for 96 h. The medium effect concentrations revealed varied sensitivity to IBU in the order Chlorella sorokiniana > Microcystis aeruginosa LE3 > Microcystis aeruginosa EAWAG 198. The drug caused a significant difference from control in cell density and chlorophyll-a of the three strains, except for chlorophyll-a in M. aeruginosa EAWAG 198 cultures where a significant difference occurred at 100 μg/L. The cell density of M. aeruginosa LE3 cultures exposed to 10 μg/L IBU increased 24 h post-exposure. Increasing concentrations of IBU induced higher total microcystins content of the Microcystis aeruginosa. Intracellular hydrogen peroxide content, peroxidase, and glutathione S-transferase activities, and lipid peroxidation increased as a function of IBU exposure. Total lipid, carbohydrate, and protein content of Chlorella sorokiniana were stimulated following IBU exposure. We conclude that the increasing presence of IBU in aquatic ecosystems could significantly alter the population dynamics of the investigated and other phytoplankton species.

ZIF-8 metal organic framework composites as hydrogen evolution reaction photocatalyst: A review of the current state

In the past decade, extensive research has been devoted to synthesis of ZIF-8 materials for catalytic applications. As physico-chemical properties are synthesis-dependent, this review explores different synthesis strategies based the solvent and solvent-free synthesis of zeolitic imidazole framework. Accordingly, the effect of several parameters on the ZIF-8 synthesis were discussed including solvent, deprotonating agents, precursors ratio is delivered. Additionally, the advantages and disadvantages of each synthesis have been discussed and assessed. ZIF-8 textural and structural properties justify its wide use as a stable high surface area MOF in aqueous catalytic reactions. This review includes the applicatios of ZIF-8 materials in photocatalytic hydrogen evolution reaction (HER). The efficiency of the reviewed materials was fairly assessed. Finally, Limitations, drawbacks and future challenges were fully debated to ensure the industrial viability of the ZIFs.

Magnetic NH2-MIL-101(Al)/Chitosan nanocomposite as a novel adsorbent for the removal of azithromycin: modeling and process optimization

In the present study, the magnetic NH₂-MIL-101(Al)/chitosan nanocomposite (MIL/Cs@Fe₃O₄ NCs) was synthesized and used in the removal of azithromycin (AZT) from an aqueous solution for the first time. The as-synthesized MIL/Cs@Fe₃O₄ NCs was characterized by SEM, TEM, XRD, FTIR, BET, and VSM techniques. The effect of various key factors in the AZT adsorption process was modeled and optimized using response surface methodology based on central composite design (RSM-CCD). The low value of p-value (1.3101e-06) and RSD (1.873) parameters, along with the coefficient of determination > 0.997 implied that the developed model was well fitted with experimental data. Under the optimized conditions, including pH: 7.992, adsorbent dose: 0.279 g/L, time: 64.256 min and AZT concentration: 10.107 mg/L, removal efficiency and AZT adsorption capacity were obtained as 98.362 ± 3.24% and 238.553 mg/g, respectively. The fitting of data with the Langmuir isotherm (R²: 0.998, X²: 0.011) and Pseudo-second-order kinetics (R²: 0.999, X²: 0.013) showed that the adsorption process is monolayer and chemical in nature. ΔH° > 0, ΔS° > 0, and ∆G° < 0 indicated that AZT removal was spontaneous and endothermic in nature. The effect of Magnesium on AZT adsorption was more complicated than other background ions. Reuse of the adsorbent in 10 consecutive experiments showed that removal efficiency was reduced by about 30.24%. The performance of MIL/Cs@Fe₃O₄ NCs under real conditions was also tested and promising results were achieved, except in the treatment of AZT from raw wastewater.

ZIF-8 metal organic framework materials as a superb platform for the removal and photocatalytic degradation of organic pollutants: a review

Metal organic frameworks (MOFs) are attracting significant attention for applications including adsorption, chemical sensing, gas separation, photocatalysis, electrocatalysis and catalysis. In particular, zeolitic imidazolate framework 8 (ZIF-8), which is composed of zinc ions and imidazolate ligands, have been applied in different areas of catalysis due to its outstanding structural and textural properties. It possesses a highly porous structure and chemical and thermal stability under varying reaction conditions. When used alone in the reaction medium, the ZIF-8 particles tend to agglomerate, which inhibits their removal efficiency and selectivity. This results in their mediocre reusability and separation from aqueous conditions. Thus, to overcome these drawbacks, several well-designed ZIF-8 structures have emerged by forming composites and heterostructures and doping. This review focuses on the recent advances on the use of ZIF-8 structures (doping, composites, heterostructures, etc.) in the removal and photodegradation of persistent organic pollutants. We focus on the adsorption and photocatalysis of three main organic pollutants (methylene blue, rhodamine B, and malachite green). Finally, the key challenges, prospects and future directions are outlined to give insights into game-changing breakthroughs in this area.

A highly stable bimetallic organic framework for enhanced electrical performance of cellulose nanofiber-based triboelectric nanogenerators

Triboelectric nanogenerators (TENGs) have garnered considerable attention as an emerging energy harvesting technology. To improve the electrical properties of the triboelectric materials in TENGs, various micro- and nanomaterials with strong charge-trapping capabilities are introduced as filler materials. However, the fillers generally perform a single function and lack long-term operational durability. Hence, further research is required to achieve stable and efficient TENGs. In this study, NH₂ metal-organic frameworks (NH₂-MOFs) were combined with a cellulose nanofiber (CNF) to prepare a composite film. NH₂-MOFs have an aminated bimetallic organic backbone with strong charge-induction and charge-trapping capabilities. Thus, their addition significantly improved the stability, positive triboelectric properties and charge-trapping performance of the composite film. The optimized composite film and a fluorinated ethylene propylene film were used as triboelectric pairs to assemble a TENG. The electrical performance of the TENG was approximately 230% greater than that of a TENG with a pure CNF film and remained very stable for at least 90 days. These results demonstrate that NH₂-MOFs are promising fillers for improving the performance of TENGs and expanding the range of materials used in TENG construction.

Easy and Low-Cost Method for Synthesis of Carbon–Silica Composite from Vinasse and Study of Ibuprofen Removal

Vinasse was successfully utilized to synthesize carbon–silica composite with a low-cost silica source available in Thailand (sodium silicate, Na2SiO3) and most commonly used source, tetraethyl orthosilicate (TEOS). The composites were prepared by a simple one-step sol–gel process by varying the vinasse (as carbon source) to silica source (Na2SiO3 or TEOS) weight ratio. The resulting composites were characterized by N2 adsorption, moisture and ash contents, pH, pHpzc, bulk density, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX). The composites had highest surface area of 313 and 456 m2/g, with average mesopore diameters of 5.00 and 2.62 nm when using Na2SiO3 and TEOS as the silica sources, respectively. The adsorption of a non-steroidal anti-inflammatory drug, ibuprofen, was investigated. The contact time to reach equilibrium was 60 min for both composites. The adsorption kinetics were fitted by a pseudo-second-order model with the correlation coefficient R2 > 0.997. The adsorption isotherms were well described by the Langmuir model (R2 > 0.992), which indicates monolayer adsorption. The maximal adsorption capacities of the Na2SiO3- and TEOS-based composites were as high as 406 and 418 mg/g at pH 2, respectively. The research results indicate that vinasse and a low-cost silica source (Na2SiO3) show great potential to synthesize adsorbents through a simple method with high efficiency.

Stable magnetic CoZn/N-doped polyhedron with self-generating carbon nanotubes for highly efficient removal of bisphenols from complex wastewaters

Bisphenols have extensively been found in various environmental matrices and caused public concerns due to their endocrine-disrupting potential. Herein, we developed a ZIF-67@ZIF-8-derived CoZn/nitrogen-doped carbon (CoZn/NC) as a robust adsorbent for bisphenols in wastewaters. The self-generating carbon nanotubes and the open metal sites provided sufficient adsorption sites. The Co component endowed the derivative with strong magnetism facilitating its separation from water. CoZn/NC exhibited exceeding water stability in pH 3 - 12 solution and withstood water up to 15 days. The great applicability of CoZn/NC was validated with 16 real wastewaters from different sources (recoveries exceeding 97.9%). Fast adsorption kinetics were observed with removal efficiencies above 96.5% within 1 min. The adsorption isotherms were well fitted with the Langmuir model, with adsorption capacities of 222, 200, 193, and 321 mg g^-1 for bisphenol A, bisphenol F, bisphenol S, and bisphenol AF, respectively. Variations in external conditions, including pH 3 - 9, humic acid (50 mg L^-1), and NaCl (0.1 mol L^-1), had negligible impacts on the adsorption process. The characterizations and density functional theory computation demonstrated that electrostatic, hydrophobic, π - π, and cation- π interactions are the driving forces in this system. The as-prepared CoZn/NC exhibits great promise in real wastewater treatment.

Sequestration and toxicological assessment of emerging contaminants with polypyrrole modified carboxymethyl cellulose (CMC/PPY): Case of ibuprofen pharmaceutical drug

Ibuprofen (IBU) is a non-steroidal anti-inflammatory drug released into water bodies causing toxic biological effects on living organisms. The current study aims to eliminate IBU from aqueous solutions by a novel carboxymethylcellulose/polypyrrole (CMC/PPY) composite with high removal efficiency. Pyrrole was polymerized to polypyrrole whose average size was about 20 nm on the CMC surface. The maximum removal percentage of IBU by CMC/PPY composite was optimized at initial concentration 10 mg/L, dosage 0.02 g, and pH 7 with adsorption capacity of 72.30 (mg/g) and removal of 83.17 %. IBU adsorption onto CMC/PPY theoretically fits into the Langmuir isotherm and Elovich-kinetic models. Fish and Phytotoxicity assessment were performed with zebrafish and seeds of Vigna mungo (VM) and Vigna radiata (VR). The toxicity study reveals that before adsorption, IBU shows high toxicity towards the zebrafish mortality (33 %), growth inhibition (58.52 % for VM, 60.84 % for VR), and germination (86.66 % for VM and 90 % for VR). As CMC/PPY adsorbs IBU, toxicity drastically decreases. Before adsorption, LC₅₀ was 233.02 mg/L. After adsorption, the LC₅₀ increases to 2325.07 mg/L as IBU molecules get adsorbed by CMC/PPY. These findings show the feasibility of preparing CMC/PPY composite to effectively remove pharmaceutical pollutant IBU from aqueous solutions with their toxicological assessment.

Ecofriendly and sustainable Sargassum spp.-based system for the removal of highly used drugs during the COVID-19 pandemic

Analgesic consumption increased significantly during the COVID-19 pandemic. A high concentration of this kind of drug is discarded in the urine, reaching the effluents of rivers, lakes, and seas. These medicines have brought serious problems for the flora and, especially, the ecosystems’ fauna. This paper presents the results of removing diclofenac, ibuprofen, and paracetamol in an aqueous solution, using Sargassum spp. from the Caribbean coast. The study consisted of mixing each drug in an aqueous solution with functionalized Sargassum spp in a container under constant agitation. Therefore, this work represents an alternative to solve two of the biggest problems in recent years; first, the reduction of the overpopulation of sargassum through its use for the remediation of the environment. Second is the removal of drug waste used excessively during the COVID-19 pandemic. Liquid samples of the solution were taken at intervals of 10 min and analyzed by fluorescence to determine the concentration of the drug.

The sorption capacity for diclofenac, ibuprofen, and paracetamol was 2.46, 2.08, and 1.41 μg/g, corresponding to 98 %, 84 %, and 54 % of removal, respectively. The removal of the three drugs was notably favored by increasing the temperature to 30 and 40 °C, reaching efficiencies close to 100 %. Moreover, the system maintains its effectiveness at various pH values. In addition, the Sargassum used can be reused for up to three cycles without reducing its removal capacity. The wide diversity of organic compounds favors the biosorption of drugs, removing them through various kinetic mechanisms. On the other hand, the Sargassum used in the drugs removal was analyzed by X-ray diffraction, FTIR spectroscopy, TGA analysis, and scanning electron microscopy before and after removal. The results showed an evident modification in the structure and morphology of the algae and demonstrated the presence of the biosorbed drugs. Therefore, this system is sustainable, simple, economical, environmentally friendly, highly efficient, and scalable at a domestic and industrial level that can be used for aquatic remediation environments.

Efficient Activation of Peroxymonosulfate by Cobalt Supported Used Resin Based Carbon Ball Catalyst for the Degradation of Ibuprofen

The extensive use of ibuprofen (IBU) and other pharmaceuticals and personal care products (PPCPs) causes them widely to exist in nature and be frequently detected in water bodies. Advanced catalytic oxidation processes (AOPs) are often used as an efficient way to degrade them, and the research on heterogeneous catalysts has become a hot spot in the field of AOPs. Among transitional metal-based catalysts, metal cobalt has been proved to be an effective element in activating peroxymonosulfate (PMS) to produce strong oxidizing components. In this study, the used D001 resin served as the matrix material and through simple impregnation and calcination, cobalt was successfully fixed on the carbon ball in the form of cobalt sulfide. When the catalyst was used to activate persulfate to degrade IBU, it was found that under certain reaction conditions, the degradation rate in one hour could exceed 70%, which was far higher than that of PMS and resin carbon balls alone. Here, we discussed the effects of catalyst loading, PMS concentration, pH value and temperature on IBU degradation. Through quenching experiments, it was found that SO4− and ·OH played a major role in the degradation process. The material has the advantages of simple preparation, low cost and convenient recovery, as well as realizing the purpose of reuse and degrading organic pollutants efficiently.

Efficient removal of mefenamic acid and ibuprofen on organo-Vts with a quinoline-containing gemini surfactant: Adsorption studies and model calculations

To pursue the adsorptivity of versatile vermiculite (Na-Vt)-based adsorbent targeted at emerging pharmaceuticals (mefenamic acid and ibuprofen, corresponding to MEA and IBP, respectively), a quinoline-based gemini surfactant (DHQU) with multi-functional groups is applied as modifier on Na-Vt. Enhanced hydrophobicity, enlarged interlayer space and decreased surface area of DHQU-Vt are obtained, whose modifier availability (the mole ratio of modifier intercalated to added) reaches up to 84.18% as characterized by FT-IR, XRD, TG-DTG, EA and BET analysis. Efficient adsorption of MEA/IBP (123.71/240.69 mg/g) is achieved under an extremely low DHQU dosage (0.2 CEC lower than the usual saturated dosage of organo-Vts), with all the processes fitting satisfactorily with pseudo-second order and Freundlich isotherm models accompanied by an exothermic nature. Acid pickling testifies a stable and reliable reusability process of DHQU-Vt even after 3 cycles. Multiple interactions (i.e., partition process, XH-π interaction, π-π interaction, π-π stacking and electrostatic interaction) are revealed and compared from not only characterization results, but also simulation of frontier orbital analysis, the adsorption configuration and bonding analysis: (i) The greater molecular flexibility of the adsorbate, the greater intra particle diffusion effect. (ii) π-π stacking between isolated aromatic rings is stronger than that between parallelly connected aromatic rings. (iii) The strength of multiple active sites provided by quinoline (CH-π, NH-π and π-π interactions) are comparable but weaker than electrostatic interaction/intra particle diffusion.

Degradation of norfloxacin by MOF-derived lamellar carbon nanocomposites based on microwave-driven Fenton reaction: Improved Fe(III)/Fe(II) cycle

In this paper, a new type of iron-based magnetic nanoparticle material embedding mesoporous carbon (Fe@C₇₀₀) was prepared by simple pyrolysis of a MIL-101-Fe precursor and employed in the microwave-catalyzed degradation of norfloxacin (NOR) with the presence of H₂O₂. Characterization results showed successful anchoring of Fe⁰ nanoparticles in the carbon matrix. Under optimal treatment conditions (Calcination temperature = 700 °C, H₂O₂ dosage = 40 mM, MW power = 500 W, NOR dosage = 50 mg L^-1 and initial pH = 4), the degradation efficiency of NOR reached 95.22%. The catalyst showed exceptional degradation properties over a relatively wide pH range. The mesoporous carbon in the catalyst promoted electron transfer, enhanced the Fe(III)/Fe(II) cycle, increased contact between Fe⁰ and Fe²⁺ with H₂O₂, and accelerated the production of ·OH. Furthermore, density functional theory (DFT) calculations were used to predict the fragile active sites in NOR and to analyze the degradation pathway of NOR in combination with intermediates. Fe@C₇₀₀ retained good activity after 5 cycles. Reduced toxicity of intermediates predicted by T.E.S.T. compared to NOR. This study presented a new avenue for the rational design of Fe⁰-carbon composites as microwave-assisted Fenton-like catalysts for potential applications in wastewater treatment.

Enhancing catalytic ozonation activity of MCM-41 via one-step incorporating fluorine and iron: The interfacial reaction induced by hydrophobic sites and Lewis acid sites

Fe-MCM-41 had been widely used as ozonation catalyst, however, the existence of large amount of hydrophilic silanol hindered its interfacial reaction with O₃ and pollutants. To solve this problem, F-Fe-MCM-41 was synthesized by co-doping F and Fe into the framework of MCM-41 to replace silanol with Si-F groups through a one-step hydrothermal method. F introduced hydrophobic sites which contributed to more ibuprofen (IBP) chemisorption on the surface of F-Fe-MCM-41. Moreover, doping F also enhanced the acidity, which accelerated O₃ decomposition into •OH. F-Fe-MCM-41/O₃ exhibited notably activity with 96.6% IBP removal efficiency within 120 min, while only 78.5% and 80.9% in O₃ alone and Fe-MCM-41/O₃, respectively. Surface Lewis acid sites and metal hydroxyl groups were considered as important factors for O₃ activation and •OH generation. F-Fe-MCM-41 exhibited excellent catalytic performance under acidic and alkaline conditions. Comparative experiments revealed that F doping improved the interfacial reaction, especially the interfacial electron transfer, which resulted in the high catalytic activity of F-Fe-MCM-41. F-Fe-MCM-41 possessed good stability and reusability, with only 5.7% decline for IBP removal in five successive cycles. Furthermore, the possible degradation path of IBP was proposed according to DFT calculation and GC-MS analysis.

Removal of naproxen from wastewater using chitosan-aerogel-activated carbon biocomposites: Theory, equilibrium, kinetics, thermodynamics, and process optimization

This study investigated the performance of chitosan-aerogel-activated carbon (CHT:AEO:AC) biocomposite as an adsorbent for the removal of naproxen from wastewater. Naproxen removal in % was 99, 33, 62, and 90 using 300 mg of raw AC, raw CHT, CHT:AEO, and CHT:AEO:AC, respectively. Langmuir, Freundlich, Dubinin-Radushkevich (D-R), and Temkin isotherm models were used to obtain adsorption isotherms. Chi-squared (χ2 ) and correlation coefficients (R2 ) values showed that the parameters of the Freundlich, Temkin, and D-R models were more suitable for naproxen adsorption than the Langmuir model for raw CHT, CHT:AEO, and CHT:AEO:AC, whereas the Langmuir model fitted well for raw AC. The adsorption of naproxen onto biocomposites was defined by pseudo-second-order kinetic model, and adsorption rate constants were 0.245, 0.036, 0.075, and 0.147 mg g-1  min-1 for raw AC, raw CHT, CHT:AEO, and CHT:AEO:AC, respectively. The impact of optimum process conditions on naproxen adsorption was explored using response surface methodology. The optimum independent variables were 288.94 mg, 29.64°C, and 372.5 min, leading to a rate of naproxen removal onto CHT:AEO:AC of 90.29%. PRACTITIONER POINTS: Naproxen adsorption from wastewater using chitosan-aerogel-activated carbon biocomposite (CHT:AEO:AC) was investigated. The effects of the amount of biocomposite, temperature, and time on the adsorption were investigated. Optimization of the process conditions was carried out using the response surface methodology.

Adsorptive remediation of naproxen from water using in-house developed hybrid material functionalized with iron oxide

Every year, a considerable volume of medications is consumed. Because these medications are not entirely eliminated in the sewage treatment plants and impact the surface waterways, the environmental pollution problem arises. This study objective was to evaluate the possibility of using an absorbent material made with of polyethylene terephthalate and sugarcane bagasse ash functionalized with iron oxide (PETSCA/Fe³⁺) in the removal of naproxen from water. The feasibility of having viable features in becoming an efficient adsorbent was first determined. The batch test was performed, allowing the dose effect, adsorption kinetics, and isotherm models to be evaluated. The determination of naproxen (NAP) concentration in water was analyzed on a high-performance liquid chromatograph and Langmuir method best represented the adsorption isotherm model. PETSCA/Fe³⁺ adsorbent material demonstrated potential in the naproxen removal at a low cost. The batching process was satisfactory, with 0.30 g of composite being the optimum fit for the system. The adsorption kinetics was determined and described by the pseudo second order model, with an average correlation coefficient (R²) of 0.974. The adsorption system model was best represented by the Langmuir isotherm curve. Moreover, adsorption in the presence of H₂O₂ had a positive impact on the process, removing 81.9% of NAP, whereas the process without H₂O₂ did not remove more than 62.0% of NAP. Therefore, because of its good qualities for NAP removal, PETSCA/Fe³⁺ is recommended as adsorbent material, primarily in small-volume water filtration systems.

Ring Vibrations to Sense Anionic Ibuprofen in Aqueous Solution as Revealed by Resonance Raman

We unravel the potentialities of resonance Raman spectroscopy to detect ibuprofen in diluted aqueous solutions. In particular, we exploit a fully polarizable quantum mechanics/molecular mechanics (QM/MM) methodology based on fluctuating charges coupled to molecular dynamics (MD) in order to take into account the dynamical aspects of the solvation phenomenon. Our findings, which are discussed in light of a natural bond orbital (NBO) analysis, reveal that a selective enhancement of the Raman signal due to the normal mode associated with the C-C stretching in the ring, νC=C, can be achieved by properly tuning the incident wavelength, thus facilitating the recognition of ibuprofen in water samples.

High spin Fe3+-related bonding strength and electron transfer for sensitive and stable SERS detection

The SERS performance of trimetallic MIL-101(FeNiTi) and the spin state of Fe3+ is positively correlated. The SERS enhancement mechanism is explored regarding the bonding strength and charge transfer between molecules and MIL-101.

Ibuprofen degradation by a synergism of facet-controlled MIL-88B(Fe) and persulfate under simulated visible light

The photocatalysis/persulfate (PS) hybrid system has proven to be a promising method for degrading organic pollutants from aqueous solutions. In this study, three MIL-88B(Fe) iron-based metal-organic framework (MOF) phases with different facet content were prepared and used both as photocatalysts and catalysts for PS activation to remove ibuprofen (IBP). The results showed that there was a close correlation between the exposed facets and the catalytic activity. MIL-88B(Fe)-1 (M88B1) with exposed {100} facets and proportionally more {101} facets showed the best catalytic activity. The optimum PS dosage used in this study was 60 mg/L. The presence of Cl^-, SO₄^2-, and NO₃^- all inhibited the degradation of IBP. X-ray photoelectron spectroscopy (XPS) showed that M88B1 possessed more Fe²⁺ than the other two MIL-88B(Fe) MOF phases, making it easier to generate active radicals through PS activation. The UV-vis diffuse reflectance spectra (DRS), photoluminescence (PL), and electrochemical analysis indicated that M88B1 possessed the highest light absorption, most active sites, and fastest charge transfer ability. Radical scavenging and electron spin resonance (ESR) experiments demonstrated that SO₄^-•, ^•OH, O₂^-•, and ¹O₂ species participated in the IBP degradation process. Furthermore, density functional theory (DFT) calculations were performed to identify the crystallographic facets, band structure, and total density of states of MIL-88B(Fe) to further confirm the mechanism of MIL-88B(Fe) as a photocatalyst and a PS activator. This work provides new insights into the synergism between photocatalysis and persulfate activation by facet-controlled MOFs for environmental remediation.