Performance of compostable baby used diapers in the composting process with the organic fraction of municipal solid waste

Effect of diaper waste on composting of household wet biodegradable waste in a decentralized system

Due to changes in lifestyle and improved economic status, the use of diapers is also increasing in developing nations. Hence, there is a need to develop an eco-friendly system for the disposal of discarded diapers which is termed diaper waste (DW). In the present study, the co-composting of DW with household wet biodegradable waste (HWBW) was performed in a compartmentalized rotary drum (CRD) (total capacity = 160 L, number of compartments = 4) under passive aeration conditions. For the co-composting runs, 1 kg of HWBW and DW mixture (mass ratio = 100:0, 90:10, 85:15, and 80:20) was added in four individual compartments daily for 10 days. During the process, the highest temperature of ~ 50-56 °C could be achieved in different compartments for a duration of 2-8 days. The compost yield (i.e., below 4 mm size material) was ranged 10.4-13% after 55 days of composting and the mass of DW was reduced by ~ 61-68%. A mixture of 15% DW and 85% HWBW can be suggested as the best combination for the co-composting process. Based on the "Dewar test" results, the samples recovered after composting could be categorized as "stable". The pot results showed an improvement in the growth of Vigna Radiata when 10% compost sample was mixed with soil whereas with 20% compost in the soil-compost mixture, the plant growth was adversely affected. Hence, co-composting of DW with HWBW can be a feasible proposition which can produce a good quality compost.

Decentralized Composting of Food Waste: A Perspective on Scientific Knowledge

Composting has been demonstrated to be an effective and sustainable technology to treat a wide variety of organic wastes. A particular aspect of composting is the number of technological options that can be used, from full-scale plants to small composters. In this sense, the interest in composting at home or on a community scale is exponentially growing in recent years, as it permits the self-management of organic wastes and obtaining compost that can be used by the same producer. However, some questions about the quality of the obtained compost or the environmental impact of home composting are still in an early stage of development and provide little knowledge. In this review, the main points related to home and community composting are analysed in detail according to the current scientific knowledge by highlighting their advantages and possible drawbacks. Particularly, the composting process performance is analysed, with temperature stratification being one of the main problems related to small amounts of organic matter. Simultaneously, compost quality is determined using parameters such as stability and/or maturity, concluding that home compost can be similar to industrial compost in both aspects. However, sanitisation of home compost is not always achieved. Regarding its environmental impact, gaseous emissions, especially greenhouse emissions, are the most studied category and are generally low. Finally, the effects of pandemics on home composting are also preliminary commented, concluding that this strategy can be a good alternative to have cities that are more resilient.

Phosphorus circular economy of disposable baby nappy waste: Quantification, assessment of recycling technologies and plan for sustainability

This study assessed the potential for minimizing human excreta bound phosphorus (P) loss through used disposable baby nappies, an area that remained unexplored for nations. Accordingly, it performed a substance flow analysis to assess the national P loss through used disposable baby nappies in the case of Australia. The analysis revealed that approximately 308 tonne P is lost through used baby nappies to landfills in Australia in 2019, which is nearly 2.5% of the overall P excreta as human waste. Although the quantity seems small in percentage term, it could result in the loss of a significant amount of P over several years, as assessed 5452 tonne P over the 2001-2019 period, which is concerning in the context of anticipated future global P scarcity. The review of peer-reviewed literature on available technologies/methods for recycling disposable baby nappy waste indicates that there are some technologies for recycling P particularly through co-composting with food and other organic wastes, while the majority of these are still at the lab/pilot scale. There are also various recycling techniques with purpose ranging from energy recovery to volume reduction, generation of pulp, hydrogel, cellulose, and polymer as well as to increase yield stress and viscosity of concrete, however, these are not effective in P recovery. The study implies that compost made of nappy waste can be used as fertilizer to produce bamboo, cotton, and maize plants to supply raw materials for producing biodegradable nappies, hence, to close the loop. The various product and system design options e.g., designing for flushing, designing for disassembling the excreta containing part, and designing for community composting suggested in this study could be further researched for identifying best suitable option to achieve P circular economy of disposable baby nappies. This study also recommends necessary interventions at various stages of the nappy life cycle to ensure sustainable management of phosphorus.

Comparison of organic substrates in urban rooftop agriculture, towards improving crop production resilience to temporary drought in Mediterranean cities

BACKGROUND

Urban agriculture contributes to meeting the growing food production demand in cities. In the context of low water availability, it is important to consider alternatives that are able to maintain production. Through a circular economy vision, this study aimed to assess the use of substrates made from local materials as an alternative for urban agriculture in periods of low water availability, due to water supply cuts. The substrates used were coir commercial organic substrate, vegetable compost from urban organic waste and perlite commercial standard substrate; a mixture of the urban compost and perlite (1:1) was used for three consecutive crop cycles of lettuce (Lactuca sativa L. var. crispa). The crop cycles were performed in the spring and summer periods of 2018 to observe the performance during warmer periods of the year in an integrated rooftop greenhouse near Barcelona. Each substrate was assessed under conventional irrigation (0-5 kPa) and temporary water restricted conditions (irrigation stopped until the water tension reached -20 kPa perlite).

RESULTS

In terms of yield, our results show that the compost and mixture were similar to those obtained from perlite (11.5% and 3.7% more production under restricted water conditions). Organic substrates increased the crop's resilience to water restriction, in contrast to the perlite. In particular, water loss took longer in coir (one- and two-crop cycle); however, when dryness began, it occurred quickly.

CONCLUSION

The vegetable compost and the substrate mixture presented tolerance to temporary water restriction when water restriction reached -20 kPa. © 2021 Society of Chemical Industry.

Synergistic effects of CO2 on complete thermal degradation of plastic waste mixture through a catalytic pyrolysis platform: A case study of disposable diaper

Consumption of diverse plastics has posed an environmental threat because their disposal practices, landfilling and incineration, release toxic chemicals and microplastics into all environmental media. Indeed, heterogeneous matrix of plastic wastes makes them hard to be disposed. As such, this study aimed to introduce an environmentally benign/reliable disposal platform for complete decomposition of plastic wastes. Pyrolysis process was adapted to convert plastics into syngas, and a disposable diaper (DD) was used as model plastic waste, because it is composed of a variety of polymeric materials. Pyrolysis of DD resulted in the formation of gaseous products and pyrogenic oils, composed of (oxygenated) hydrocarbons. Nonetheless, reactivity of CO₂ as an oxidant in pyrolysis of DD was negligible. To impart the strong/desired reactivity of CO₂, Ni-based catalyst was adopted. Ni catalyst enhanced H₂ and CO formations 4 and 15 times more than pyrolysis without catalyst at 700 °C under CO₂. The value-added syngas production was originated from the reduction of polymeric waste, and its derivatives including aromatic compounds. Thus, CO₂ offered a strategic means to produce value-added chemicals and reduce aromaticity of pyrogenic products. The observations could offer an innovative way to control the fate of toxic chemicals derived from plastic pyrolysis.

Municipal Solid Waste Thermal Analysis—Pyrolysis Kinetics and Decomposition Reactions

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Organic waste materials were divided into six basic groups as follows: paper, cardboard, textiles, plastics, hygiene waste, and biodegradable waste. For each group, two waste materials were selected to be studied. Research materials were (i) paper (receipts, cotton wool); (ii) cardboard (cardboard, egg carton); (iii) textiles (cotton, leather); (iv) plastics (polyethylene (PET), polyurethane (PU)); (v) hygiene waste (diapers, leno); and (vi) biodegradable waste (chicken meat, potato peel). Waste materials were chosen to represent the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to the Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton, 134.5 kJ × (mol∙K)−1, and the lowest for leather, 25.2 kJ × (mol∙K)−1. The DSC analysis showed that a number of transformations occurred during pyrolysis for each material. For each transformation, the normalized energy required for transformation, or released during transformation, was determined, and then summarized to present the energy balance. The study found that the energy balance was negative for only three waste materials—PET (−220.1 J × g−1), leather (−66.8 J × g−1), and chicken meat (−130.3 J × g−1)—whereas the highest positive balance value was found for potato peelings (367.8 J × g−1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

Detailed municipal solid waste composition analysis for Nur-Sultan City, Kazakhstan with implications for sustainable waste management in Central Asia

A detailed characterization of municipal solid waste (MSW) beyond a standard compositional analysis may offer insights useful for improving waste management systems. The present paper contributes to the scarce literature in the field by presenting new data from a rapidly developing Central Asian city, the capital of Kazakhstan, Nur-Sultan. Three sampling campaigns (each 1 week long) have been conducted at the city landfill over a 1-year period (2018-2019), and a detailed characterization for selected waste components and sub-components has been performed. The major fractions of MSW were organics (46.3%), plastics (15.2%), paper (12.8%), and diapers (5.9%). The detailed composition analysis showed high LDPE (low-density polyethylene) content (5.5%) mostly comprised of plastic bags (4.5%), transparent glass (3.2%), pharmaceuticals (0.4%), and fine (i.e., < 12 mm) organic fraction content (29%). The MSW generation rate of Nur-Sultan was estimated as 1.47 kg capita^-1 day^-1 based on the field collection as well as literature data. Among sustainable waste management recommendations addressed for Nur-Sultan and applicable to other cities in Central Asia, composting is recommended due to high organics fraction in MSW and its great potential to reduce the landfilled waste volume and to help valorizing the waste.

Pretreatment of used disposable nappies: Super absorbent polymer deswelling

Typical used disposable nappies usually consist of nonwoven fabrics, Super Absorbent Polymer (SAP), and organic material, namely fluffy pulp, urine and/or excreta. Currently, this waste stream is being disposed to landfills causing many environmental issues. An alternative management method could be the valorisation of the biodegradable material through anaerobic digestion, and the recycling of plastics and SAP. Pretreatment of nappies is mandatory to separate SAP and plastics from the organic material. The aim of this work was the development of a process to minimize SAP's volume, as this component can swell up to 1500 times its own mass by water absorbance, thus hindering any further biological process. CaCl₂, MgCl₂, and a range of CaCl₂/MgCl₂ combinations were tested against their deswelling efficiency on SAP, residual reagent concentration and reagent cost. The mixture of 20% CaCl₂ and 50% MgCl₂ (w/w) of SAP was concluded as the suitable combination of salts achieving a final SAP volume reduction of 92.7% with low residual cation concentrations and minimum cost. The physicochemical characterization of nappies' hydrolysate that took place to estimate its adequacy as substrate for anaerobic digestion resulted to a COD:N ratio within the acceptable range for a subsequent anaerobic digestion processing.

Assessment of Used Baby Diapers Composting in Bolivia

Solid waste open dumping in developing countries is a global concern. To move towards sustainable development, mixed waste should be reduced, and recyclable waste recovered. The aim of the current research was to find appropriate solutions to disposable used baby-diapers recycling in Bolivia since it is a waste fraction widely produced and commonly disposed of in open dumps. Composting of the organic diaper hydrogel was assessed in five trials, adding components available locally: cow dung, activated bacteria, and Californian red earthworms (Eisenia fetida). It was observed that about 60 days were globally required for biomass decomposition with cow dung, activated bacteria, and earthworms, and more than 70 days for the treatment of the substrate mixed only with manure, while the diaper hydrogel did not degrade without cow dung. This research is the first that attempted to treat disposable used baby diapers with the vermicomposting process. In general, the outcomes of the research are promising: vermicomposting with cow manure can be a recycling option for disposable used baby diapers, introducing appropriate practices toward a circular economy in developing regions.

Microwave pyrolysis valorization of used baby diaper

Used baby diaper consists of a combination of decomposable cellulose, non-biodegradable plastic materials (e.g. polyolefins) and super-absorbent polymer materials, thus making it difficult to be sorted and separated for recycling. Microwave pyrolysis was examined for its potential as an approach to transform used baby diapers into value-added products. Influence of the key operating parameters comprising process temperature and microwave power were investigated. The pyrolysis showed a rapid heating process (up to 43 °C/min of heating rate) and quick reaction time (20-40 min) in valorizing the used diapers to generate pyrolysis products comprising up to 43 wt% production of liquid oil, 29 wt% gases and 28 wt% char product. Microwave power and operating temperature were observed to have impacts on the heating rate, process time, production and characteristics of the liquid oil and solid char. The liquid oil contained alkanes, alkenes and esters that can potentially be used as chemical additives, cosmetic products and fuel. The solid char contained high carbon, low nitrogen and free of sulphur, thus showing potential for use as adsorbents and soil additives. These observations demonstrate that microwave pyrolysis has great prospect in transforming used baby diaper into liquid oil and char products that can be utilised in several applications.

Assessing the alteration of physicochemical characteristics in composted organic waste in a prototype decentralized composting facility

This article presents the pilot experience of an integrated biowaste management system developed in Tinos island, Greece, which promoted source separation and decentralized composting in a prototype unit. This system was introduced as a new-to-the-area of implementation and innovation, since landfilling of mixed municipal solid waste has been the common practice in Tinos island, as in many other areas of insular and mainland Greece. The biowaste management system was implemented through a bring scheme that aimed at motivating the public to separate at source the organic fraction of MSW. The system was monitored on an input-output basis of critical parameters used to assess the purity of separately collected biowaste, the treatment efficiency of the prototype unit, the quality characteristics of compost produced, and public's awareness and participation. Results showed that biowaste source separation was practiced effectively by citizens, giving high-purity feed (> 98%). Compost samples were examined in comparison with the proposed EU End-of-Waste (EoW) quality criteria and fulfilled the requirements set. More specifically, the average values of compost samples regarding heavy metal content were 72% lower than the EoW limit value for Cd, 43% lower for Ni, 38% lower for Pd, 24% lower for Cu, and 36% lower for Zn. Examined composts also met the EoW criteria for phytotoxicity and pathogenic or parasitic microorganisms, while they showed an approx. 15% decrease in initial organic matter content. Moreover, this study analyzed the carbon balances and the degree that composting can sequestrate carbon. Overall, this study demonstrated that the development and operation of on-island, decentralized composting, when properly practiced, is a sustainable option in order for islands and remote areas to adopt a closed loop approach to the biowaste management problem, in line with the circular economy principles.

Pilot trial on separation conditions for diaper recycling

By utilizing laboratory-scale tests, the optimal separation conditions for diaper recycling were identified, and then, these conditions were validated by a pilot trial. In this research, we determined the mass balances derived during various processing steps and identified the most feasible procedures to use for separating each material in the output flow. The results showed that drum screening was not able to remove all the fiber and super absorbent particles (SAP) in the plastic-rich fraction and that cellulose enzyme treatment can be a good solution. To achieve better separation of fibers and SAP, slot screening followed by a cleaner is a potential option. A feasible diaper recycling process was recommended based on these results. This process involves screening and enzymatic treatment for the plastic fraction, and screening, cleaning, and thickening for the fiber fraction. Treatment procedures were also proposed for the SAP fraction and rejected materials.

Biohydrogen production from used diapers: Evaluation of effect of temperature and substrate conditioning

This research assessed the viability to use disposable diapers as a substrate for the production of biohydrogen, a valuable clean-energy source. The important content of cellulose of disposable diapers indicates that this waste could be an attractive substrate for biofuel production. Two incubation temperatures (35 °C and 55 °C) and three diaper conditioning methods (whole diapers with faeces, urine, and plastics, WD; diapers without plastic components, with urine and faeces, DWP; diapers with urine but without faeces and plastic, MSD) were tested in batch bioreactors. The bioreactors were operated in the solid substrate anaerobic hydrogenogenic fermentation with intermittent venting mode (SSAHF-IV). The batch reactors were loaded with the substrate at ca. 25% of total solids and 10% w/w inoculum. The average cumulative bioH₂ production followed the order WD > MSD > DWP. The bio-H₂ production using MSD was unexpectedly higher than DWP; the presence of plastics in the first was expected to be associated to lower degradability and H2 yield. BioH₂ production at 55 °C was superior to that of 35 °C, probably owing to a more rapid microbial metabolism in the thermophilic regime. The results of this work showed low yields in the production of H₂ at both temperatures compared with those reported in the literature for municipal and agricultural organic waste. The studied process could improve the ability to dispose of this residue with H₂ generation as the value-added product. Research is ongoing to increase the yield of biohydrogen production from waste disposable diapers.

Organic fraction of municipal solid waste from mechanical selection: biological stabilization and recovery options

Although current trends address towards prevention strategies, the organic fraction of municipal solid waste is greatly produced, especially in high-income contexts. Its recovery-oriented collection is a common practice, but a relevant portion of the biodegradable waste is not source selected. Mechanical and biological treatments (MBT) are the most common option to sort and stabilize the biodegradable matter ending in residual waste stream. Following the changes of the framework around waste management, this paper aimed at analyzing the quality of the mechanically selected organic waste produced in MBT plants, in order to discuss its recovery options. The material performance was obtained by its composition as well as by its main chemical and physical parameters; biological stability was also assessed by both aerobic and anaerobic methods. On this basis, the effectiveness of an aerobic biostabilization process was assessed at pilot scale. After 21 days of treatment, results proved that the biomass had reached an acceptable biostabilization level, with a potential Dynamic Respirometric Index (DRIP) value lower than the limit required for its use as daily or final landfill cover material. However, the final stabilization level was seen to be influenced by scaling factors and the 21 days of treatment turned to be not so adequate when applied in the existing full-scale facility.

Home composting versus industrial composting: influence of composting system on compost quality with focus on compost stability

Stability is one of the most important properties of compost obtained from the organic fraction of municipal solid wastes. This property is essential for the application of compost to land to avoid further field degradation and emissions of odors, among others. In this study, a massive characterization of compost samples from both home producers and industrial facilities is presented. Results are analyzed in terms of chemical and respiration characterizations, the latter representing the stability of the compost. Results are also analyzed in terms of statistical validation. The main conclusion from this work is that home composting, when properly conducted, can achieve excellent levels of stability, whereas industrial compost produced in the studied facilities can also present a high stability, although an important dispersion is found in these composts. The study also highlights the importance of respiration techniques to have a reliable characterization of compost quality, while the chemical characterization does not provide enough information to have a complete picture of a compost sample.

Treatment of the biodegradable fraction of used disposable diapers by co-digestion with waste activated sludge

The results presented in this paper are part of a project aimed at designing an original solution for the treatment of used disposable diapers permitting the recycling of materials and the recovery of energy. Diapers must be collected separately at source and transported to an industrial facility to undergo special treatment which makes it possible to separate plastics and to recover a biodegradable fraction (BFD) made up mainly of cellulose. The methane yield of BFD was measured and found to be 280 ml CH4/g VSfed on average. 150 kg of dry BFD can be retrieved from the treatment of one ton of used disposable diapers, representing an energy potential of about 400 kW h of total energy or 130 kW h of electricity. As the treatment process for used diapers requires very high volumes of water, the setting up of the diaper treatment facility at a wastewater treatment plant already equipped with an anaerobic digester offers the advantages of optimizing water use as well as its further treatment and, also, the anaerobic digestion of BFD. The lab-scale experiments in a SBR showed that BFD co-digestion with sewage sludge (38% BFD and 62% waste activated sludge on volatile solids basis) was feasible. However, special attention should be paid to problems that might arise from the addition of BFD to a digester treating WAS such as insufficient mixing or floating particles leading to the accumulation of untreated solids in the digester.