Removal of sulfonamide antibiotics and human metabolite by biochar and biochar/H2O2 in synthetic urine

First insight into the environmental fate of N-acetylated sulfonamides from wastewater disinfection to solar-irradiated receiving waters

The worldwide detection of emerging transformation products of organic micropollutants has raised accumulating concerns owing to their unknown environmental fate and undesired toxicity. This work first explored the reaction kinetics and mechanisms of the prevalent N-acetylated sulfonamides (N4-AcSAs, the typical sulfonamide metabolites) from wastewater disinfection to solar-irradiated receiving waters. The transformation scenarios included chlorination/bromination, photodegradation, and solar/chlorine treatment. The halogenations of two N4-AcSAs (N4-acetylated sulfadiazine, N4-AcSDZ; N4-acetylated sulfamethoxazole, N4-AcSMX) were pH-dependent at pH 5.0-8.0, and the reactions between the neutral forms of oxidants and anionic N4-AcSAs dominated the process. Furthermore, solar-based photolysis significantly eliminated N4-AcSAs in small water bodies with low dissolved organic carbon levels, while the indirect photolysis mediated by hydroxyl radicals and carbonate radicals contributed the most. The presence of chlorine residues in solar-irradiated wastewater effluents promoted the decay of N4-AcSAs, in which the generated hydroxyl radicals and ozone played a major role. Product analysis suggested the main transformation patterns of N4-AcSAs during the above scenarios included electrophilic attack, bond cleavage, SO2 extrusion, hydroxylation, and rearrangement. Multiple secondary products maintained higher persistence, mobility, and toxicity to aquatic organisms than N4-AcSAs. Overall, the natural and engineered transformations of such micropollutants underlined the necessity of including their degradation products in future chemical management and risk assessment.

Mechanism of adsorption and targeted degradation of antimicrobial micropollutant sulfamethoxazole in aquatic environments

FHWSB as an integrated absorptive catalyst, based on Walnut shell biochar (WSB) via hydrochloric acid modification and ferrous chloride impregnation, was prepared, reacted with H2O2 to generate active free radicals •OH and •O2-, which oxidized and degraded about 80% of micro-pollutant sulfamethoxazole (SMX) from water, effectively resolving micro-pollutants' removal being inefficient because of high toxicity, persistence, and bioaccumulation in existed methods. It was clarified the specific degradation pathways and mechanisms of SMX by FHWSB synergistic H2O2 via characterization and analysis assisted DFT calculations. Furthermore, it was found that the toxicity of a series of intermediates produced by SMX degraded continued to decline, consistent with its direction of degradation via toxicological analysis. The work provides a simple and feasible strategy for the effective removal of antibiotic micro-pollutants in aquatic environments.

General performance, kinetic modification, and key regulating factor recognition of microalgae-based sulfonamide removal

Sulfonamides have been widely detected in water treatment plants. Advanced wastewater treatment for sulfonamide removal based on microalgal cultivation can reduce the ecological risk after discharge, achieve carbon fixation, and simultaneously recover bioresource. However, the general removal performance, key factors and their impacts, degradation kinetics, and potential coupling technologies have not been systematically summarized. To guide the construction and enhance the efficient performance of the purification system, this study summarizes the quantified characteristics of sulfonamide removal based on more than 100 groups of data from the literature. The biodegradation potential of sulfonamides from different subclasses and their toxicity to microalgae were statistically analyzed; therefore, a preferred option for further application was proposed. The mechanisms by which the properties of both sulfonamides and microalgae affect sulfonamide removal were comprehensively summarized. Thereafter, multiple principles for choosing optimal microalgae were proposed from the perspective of engineering applications. Considering the microalgal density and growth status, a modified antibiotic removal kinetic model was proposed with significant physical meaning, thereby resulting in an optimal fit. Based on the mechanism and regulating effect of key factors on sulfonamide removal, sensitive and feasible factors (e.g., water quality regulation, other than initial algal density) and system coupling were screened to guide engineering applications. Finally, we suggested studying the long-term removal performance of antibiotics at environmentally relevant concentrations and toxicity interactions for further research.

Fe-N co-doped biochar derived from biomass waste triggers peracetic acid activation for efficient water decontamination

In this study, the porous carbon material (FeN-BC) with ultra-high catalytic activity was obtained from waste biomass through Fe-N co-doping. The prominent degradation rate (> 96.8%) of naproxen (NAP) was achieved over a wide pH range (pH 3.0-9.0) in FeN-BC/PAA system. Unlike previously reported iron-based peracetic acid (PAA) systems with •OH or RO• as the dominated reactive species, the degradation of contaminants was attributed to singlet oxygen (1O2) produced by organic radicals (RO•) decomposition, which was proved to be thermodynamically feasible and favorable by theoretical calculations. Combining the theoretical calculations, characteristic and experimental analysis, the synergistic effects of Fe and N were proposed and summarized as follows: i) promoted the formation of extensive defects and Fe0 species that facilitated electron transfer between FeN-BC and PAA and continuous Fe(II) generation; ii) modified the specific surface area (SSA) and the isoelectric point of FeN-BC in favor of PAA adsorption on the catalyst surface. This study provides a strategy for waste biomass reuse to construct a heterogeneous catalyst/PAA system for efficient water purification and reveals the synergistic effects of typical metal-heteroatom for PAA activation.

Photo-enhanced oxidation of arsenite by biochar: The effect of pH, kinetics and mechanisms

The persistent and photo-induced free radicals of biochar play significant roles in the transformation or degradation of inorganic and organic pollutants. However, the redox capacity of biochar for arsenite (As(III)) photochemistry under different pH conditions remains unclear. In this study, we discovered that solar radiation primarily expedited the oxidation of As(III) by biochar by augmenting the production of reactive oxygen species (ROS). Biochar demonstrated a strong pH reliance on the photooxidation of As(III). Under acidic and neutral conditions, solar radiation amplified the generation of •OH (hydroxyl radicals) by BC-P (phenolic -OH of biochar) and semiquinone-type BC-PFRs (persistent free radicals of biochar) by 4.9 and 2.0 times, respectively, resulting in enhanced As(III) oxidation. Under alkaline conditions, BC-P and BC-Q (quinoid CO of biochar) facilitated the production of H2O2 (hydrogen peroxide) by 2.1 times through the spontaneous formation of semiquinone-type BC-PFRs via an anti-disproportionation reaction, promoting approximately 88.2% of As(III) photooxidation. Furthermore, solar radiation elevated around 11.8% As(III) oxidation driven by BC-Q and semiquinone-type BC-PFRs. This study provides a crucial theoretical foundation for using biochar to treat arsenic pollution in aquatic systems and understanding the migration and transformation of arsenic in different environments.

Effect of municipal sludge-based biochar produced at different pyrolysis temperatures on humification and oxytetracycline degradation of pig manure composting

This study explored the influence of pyrolysis temperatures on the properties of municipal sludge-based biochar (MSB) and evaluated the impact of MSB on humification and oxytetracycline (OTC, a broad-spectrum antibiotic) degradation in pig manure composting. Three types of MSB were produced from sewage sludge pyrolyzed at 300 °C, 500 °C, and 700 °C, respectively. Results indicated that pyrolysis temperature adjusted the formation sequence of the functional groups in MSB, and higher pyrolysis temperatures enriched the aromaticity of the biochar and augmented the concentrations of humic precursor compounds. The MSB addition to pig manure composting enhanced the peak temperature and prolonged the thermophilic phase. Moreover, the MSB addition significantly increased the HI (humic acid/fulvic acid) values (1.6-2.57) compared with the control (1.28), with a more pronounced effect observed at higher biochar pyrolysis temperatures. Furthermore, the MSB reduced the half-life of OTC degradation (1.47-2.44 d) during composting, accelerating its degradation compared with the control (2.66 d). The study demonstrated that the MSB provided a substantial amount of humic precursor materials into the composting process while also expediting the degradation of organic matter, thereby enhancing the humification process. Moreover, the extended duration of the thermophilic phase accelerated the degradation of OTC and shortened its half-life. Notably, the MSB at 700 °C had the best performance compared with other MSBs.

Improved remediation of amoxicillin-contaminated water by floating treatment wetlands intensified with biochar, nutrients, aeration, and antibiotic-degrading bacteria

Residual antibiotics have become emerging contaminants of concern for their adverse impact on the ecosystem. Additionally, their accumulation in the environment is increasing antibiotic resistance among pathogens. This study assessed the impact of intensification of biochar, nutrients, aeration, and bacteria (BNAB) on the remediation potential of floating treatment wetlands (FTWs) to treat amoxicillin (AMX)-contaminated water. The FTWs were developed with saplings of Vetiveria zizanioides and intensified with biochar (1.5%), nutrients (25 mgL-1 N, 25 mgL-1 P, 20 mg L1 K), aeration (7 mg L-1), and AMX-degrading bacteria. The results showed that all the amendments enhanced the AMX degradation, while the maximum reduction in COD (89%), BOD (88%), TOC (87%), and AMX (97%) was shown by the combined application of all the amendments. The combined application also enhanced plant growth and persistence of the inoculated bacteria in the water, roots, and shoots. This approach can be employed for the low-cost, environment-friendly treatment, and recycling of antibiotic-contaminated wastewater, where BNAB intensification can further improve the bioremediation efficiency of FTWs in the case of heavily polluted waters.

Overcoming hydrogen loss in single-chamber microbial electrolysis cells by urine amendment

The effective hydrogen production in single-chamber microbial electrolysis cells (MECs) has been seriously challenged by various hydrogen consumers resulting in substantial hydrogen loss. In previous studies, the total ammonia nitrogen (TAN) has been used to inhibit certain hydrogen-consuming microorganisms to enhance hydrogen production in fermentation. In this study, we explored the feasibility of using source-separated urine to overcome hydrogen loss in the MEC, with the primary component responsible being TAN generated via urea hydrolysis. Experimental results revealed that the optimal TAN concentration ranged from 1.17 g N/L to 1.75 g N/L. Within this range, the hydrogen production rate substantially improved from less than 100 L/(m3·d) up to 520 L/(m3·d), and cathode recovery efficiency and energy recovery efficiency were greatly enhanced, with the hydrogen percentage achieved over 95 % of the total gas volume, while maintaining uninterrupted electroactivity in the anode. Compared to using chemically added TAN, using source separated urine as the source of ammonia also showed the effect of overcoming hydrogen loss but with lower Coulombic efficiency due to the complex organic components. Pre-adaptation of the reactor with urea enhanced hydrogen production by nearly 60 %. This study demonstrated the effectiveness of TAN and urine in suppressing hydrogen loss, and the results are highly relevant to MECs treating real wastewater with high TAN concentrations, particularly human fecal and urine wastewater.

Unveiling the mechanisms of peracetic acid activation by iron-rich sludge biochar for sulfamethoxazole degradation with wide adaptability

Advanced oxidation processes (AOPs) based on peracetic acid (PAA) has been extensively concerned for the degradation of organic pollutants. In this study, metallic iron-modified sludge biochar (Fe-SBC) was employed to activate PAA for the removal of sulfamethoxazole (SMX). The characterization results indicated that FeO and Fe2O3 were successfully loaded on the surface of the sludge biochar (SBC). Fe-SBC/PAA system achieved 92% SMX removal after 30 min. The pseudo-first-order kinetic reaction constant of the Fe-SBC/PAA system was 7.34 × 10-2 min-1, which was 2.4 times higher than the SBC/PAA system. The degradation of SMX was enhanced with increasing the Fe-SBC dosage and PAA concentration. Apart from Cl-, NO3- and SO42- had a negligible influence on the degradation of SMX. Quenching experiments and electron paramagnetic resonance (EPR) techniques identified the existence of reactive species, of which CH3C(O)OO•, 1O2, and O2•- were dominant reactive species in Fe-SBC/PAA system. The effect of different water matrices on the removal of SMX was investigated. The removal of SMX in tap water and lake water were 79% and 69%, respectively. Four possible pathways for the decay of SMX were presented according to the identification of oxidation products. In addition, following the ecological structure-activity relationship model (ECOSAR) procedure and the germination experiments with lettuce seeds to predict the toxicity of the intermediates. The acute and chronic ecotoxicity of SMX solution was dramatically diminished by processing with Fe-SBC/PAA system. In general, this study offered a prospective strategy for the degradation of organic pollutants.

Highly dispersed redox antimony oxide pairs for accurate detection and electrochemistry-controlled recovery toward an antibiotic drug: Sulfadiazine

BACKGROUND

Sulfadiazine (SDZ) is a broad-spectrum antibiotic widely used in aquaculture and animal husbandry and it is easy to remain in the water system to damage the human body. Therefore, detection and removal of sulfadiazine in water systems become critical. Nowadays, catalysts and visible light are used to degrade sulfadiazine into smaller molecules containing N and S to reduce toxicity. However, these small molecules are easily released into water and the atmosphere to be the acid rain. Therefore, it is urgent to design a sensor with the ability to detect and remove SDZ at the same time. (96) RESULTS: We designed a novel composite catalyst sensor (Sb6O13@LTA GCE) with the ability to simultaneously monitor and remove sulfadiazine. The catalyst is generated by introducing SbCl5 into the reactive gel of LTA (Linde Type A) structure zeolite. In the hydrothermal reaction, the corrosive SbCl5 is transferred into nanosized Sb6O13 nanoparticle which is highly dispersed in the opening nano-scaled windows of the zeolite through redox and self-assembled progress. In the selected electrochemical overpotential range, the Sb6O13@LTA composited modified electrode could complete adsorption and desorption of SDZ through the electron transfer from Sb3+ to Sb5+. As the catalyst is in high stability, the only loss in the whole process of recovering SDZ is a small amount of electric energy. The extra-low detection limit and the removal efficiency of Sb6O13@LTA GCE have been achieved 4.0 pM and 19.3 mg/20 mg (136) SIGNIFICANCE: The prepared novel sensor has low detection limit, high removal efficiency and high selectivity for sulfadiazine. The Sb6O13@LTA GCE sensor, which is low-cost and has a simple preparation method, exhibits good reproducibility in both seawater and cell fluid. This provides the possibility for wide application in detecting and removing SDZ in water system. (53).

Enhanced removal of sulfonamide antibiotics from water by phosphogypsum modified biochar composite

Antibiotic pollution has become a global eco-environmental issue. To reduce sulfonamide antibiotics in water and improve resource utilization of solid wastes, phosphogypsum modified biochar composite (PMBC) was prepared via facile one-step from distillers grains, wood chips, and phosphogypsum. The physicochemical properties of PMBC were characterized by scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), Zeta potential, X-ray diffraction (XRD), etc. The influencing factors, adsorption behaviors, and mechanisms of sulfadiazine (SD) and sulfamethazine (SMT) onto PMBC were studied by batch and fixed bed column adsorption experiments. The results showed that the removal rates of SD and SMT increased with the increase of phosphogypsum proportion, while decreased with the increase of solution pH. The maximum adsorption capacities of modified distillers grain and wood chips biochars for SD were 2.98 and 4.18 mg/g, and for SMT were 4.40 and 8.91 mg/g, respectively, which was 9.0-22.3 times that of pristine biochar. Fixed bed column results demonstrated that PMBC had good adsorption capacities for SD and SMT. When the solution flow rate was 2.0 mL/min and the dosage of PMBC was 5.0 g, the removal rates of SD and SMT by modified wood chips biochar were both higher than 50% in 4 hr. The main mechanisms of SD and SMT removal by PMBC are hydrogen bonding, π-π donor-acceptor, electrostatic interaction, and hydrophobic interaction. This study provides an effective method for the removal of antibiotics in water and the resource utilization of phosphogypsum.

Microalgae systems - environmental agents for wastewater treatment and further potential biomass valorisation

Water is the most valuable resource on the planet. However, massive anthropogenic activities generate threatening levels of biological, organic, and inorganic pollutants that are not efficiently removed in conventional wastewater treatment systems. High levels of conventional pollutants (carbon, nitrogen, and phosphorus), emerging chemical contaminants such as antibiotics, and pathogens (namely antibiotic-resistant ones and related genes) jeopardize ecosystems and human health. Conventional wastewater treatment systems entail several environmental issues: (i) high energy consumption; (ii) high CO₂ emissions; and (iii) the use of chemicals or the generation of harmful by-products. Hence, the use of microalgal systems (entailing one or several microalgae species, and in consortium with bacteria) as environmental agents towards wastewater treatment has been seen as an environmentally friendly solution to remove conventional pollutants, antibiotics, coliforms and antibiotic resistance genes. In recent years, several authors have evaluated the use of microalgal systems for the treatment of different types of wastewater, such as agricultural, municipal, and industrial. Generally, microalgal systems can provide high removal efficiencies of: (i) conventional pollutants, up to 99%, 99%, and 90% of total nitrogen, total phosphorus, and/or organic carbon, respectively, through uptake mechanisms, and (ii) antibiotics frequently found in wastewaters, such as sulfamethoxazole, ciprofloxacin, trimethoprim and azithromycin at 86%, 65%, 42% and 93%, respectively, through the most desirable microalgal mechanism, biodegradation. Although pathogens removal by microalgal species is complex and very strain-specific, it is also possible to attain total coliform and Escherichia coli removal of 99.4% and 98.6%, respectively. However, microalgal systems' effectiveness strongly relies on biotic and abiotic conditions, thus the selection of operational conditions is critical. While the combination of selected species (microalgae and bacteria), ratios and inoculum concentration allow the efficient removal of conventional pollutants and generation of high amounts of biomass (that can be further converted into valuable products such as biofuels and biofertilisers), abiotic factors such as pH, hydraulic retention time, light intensity and CO₂/O₂ supply also have a crucial role in conventional pollutants and antibiotics removal, and wastewater disinfection. However, some rationale must be considered according to the purpose. While alkaline pH induces the hydrolysis of some antibiotics and the removal of faecal coliforms, it also decreases phosphates solubility and induces the formation of ammonium from ammonia. Also, while CO₂ supply increases the removal of E. coli and Pseudomonas aeruginosa, as well as the microalgal growth (and thus the conventional pollutants uptake), it decreases Enterococcus faecalis removal. Therefore, this review aims to provide a critical review of recent studies towards the application of microalgal systems for the efficient removal of conventional pollutants, antibiotics, and pathogens; discussing the feasibility, highlighting the advantages and challenges of the implementation of such process, and presenting current case-studies of different applications of microalgal systems.

Performance and Mechanism of Functionalized Water Hyacinth Biochar for Adsorption and Removal of Benzotriazole and Lead in Water

In this paper, water hyacinth is used to prepare biochar (WBC). A biochar-aluminum-zinc-layered double hydroxide composite functional material (WL) is synthesized via a simple co-precipitation method which is used to adsorb and remove benzotriazole (BTA) and lead (Pb²⁺) in an aqueous solution. In particular, this research paper uses various characterization methods to analyze WL and to explore the adsorption performance and adsorption mechanism of WL on BTA and Pb²⁺ in an aqueous solution through batch adsorption experiments combined with model fitting and spectroscopy techniques. The results indicate that the surface of WL contains a thick sheet-like structure with many wrinkles which would provide many adsorption sites for pollutants. At room temperature (25 °C), the maximum adsorption capacities of WL on BTA and Pb²⁺ are 248.44 mg·g^-1 and 227.13 mg·g^-1, respectively. In a binary system, during the process of using WL to adsorb BTA and Pb²⁺, compared with that in the absorption on Pb²⁺, WL shows a stronger affinity in the adsorption on BTA, and BTA would thus be preferred in the absorption process. The adsorption process of WL on BTA and Pb²⁺ is spontaneous and is endothermic monolayer chemisorption. In addition, the adsorption of WL on BTA and Pb²⁺ involves many mechanisms, but the main adsorption mechanisms are different. Among them, hydrogen bonding dominates the adsorption on BTA, while functional groups (C-O and C=O) complexation dominates the adsorption on Pb²⁺. When WL adsorbs BTA and Pb²⁺, the coexistence of cations (K⁺, Na⁺, and Ca²⁺) has a strong anti-interference ability, and WL can use a lower concentration of fulvic acid (FA) (<20 mg·L^-1) to improve its adsorption performance. Last but not least, WL has a stable regenerative performance in a one-component system and a binary system, which indicates that WL has excellent potential for the remediation of BTA and Pb²⁺ in water.

Impact of aqueous environments on hydrogen peroxide activation by manganese oxides: Kinetics and the critical role of bicarbonate

MnO₂ activating H₂O₂ is a promising way in the field of advanced oxidation processes (AOPs) and in situ chemical oxidation (ISCO) to remove contaminants. However, few studies have focused on the influence of various environmental conditions on the performance of MnO₂-H₂O₂ process, which restricts the application in real world. In this study, the effect of essential environmental factors (ionic strength, pH, specific anions and cations, dissolved organic matter (DOM), SiO₂) on the decomposition of H₂O₂ by MnO₂ (ε-MnO₂ and β-MnO₂) were investigated. The results suggested that H₂O₂ degradation was negatively correlated with ionic strength and strongly inhibited under low pH conditions and with phosphate existence. DOM had a slight inhibitory effect while Br^-, Ca²⁺, Mn²⁺ and SiO₂ placed negligible impact on this process. Interestingly, HCO₃^- inhibited the reaction at low concentrations but promoted H₂O₂ decomposition at high concentrations, possibly due to the formation of peroxymonocarbonate. This study may provide a more comprehensive reference for potential application of H₂O₂ activation by MnO₂ in different water systems.

A novel heterogeneous catalytic system (AC/ZVI/CaO2) promotes simultaneous removal of phosphate and sulfamethazine: Performance, mechanism and application feasibility verification

The eutrophication and pharmaceutical residue are the key issues to the treatment of rural non-point source pollution, concerning risks to aquatic ecosystems and human health. In this study, a novel activated carbon/zero-valent iron/calcium peroxide (AC/ZVI/CaO₂) catalytic system was constructed to remove simultaneously typical rural non-point source pollutants: phosphate and sulfamethazine (SMZ). The optimal mass ratio of the system was determined as 20% AC, 48% ZVI and 32% CaO₂. It was shown that the removal efficiency of phosphorus (P) and SMZ exceeded 65% and 40% in pH 2-11, respectively. It worked well in the presence of typical anions and humic acid. The mechanistic analyses for P removal indicated that AC/ZVI/CaO₂ system can effectively load P by the formation of crystalline state Ca-P species and Fe-P/Ca-P amorphous state coprecipitates under neutral and acidic conditions, respectively. The presence of AC in AC/ZVI/CaO₂ system could form iron-carbon micro-electrolysis process for accelerating Fenton reaction in acidic environment. And AC also can produce reactive oxygen species for the SMZ degradation by relying on persistent free radicals/graphitic carbon catalysis under environmental condition. In addition, we developed a low-impact development stormwater filter for application feasibility verification of the system. Feasibility analysis showed that the system could save up to ∼50% cost in contrast with the price of Phoslock (a commercial P load product) and presented advantages of non-toxicity, long-acting, stability and the potential to promote biodegradation by provision of aerobic environment.

Mesoporous carbon material prepared from sewage sludge hydrochar using Pluronic F127 as template for efficient removal of phenolic compounds: Experimental study and mechanism interpretation via advanced statistical physics model

Mesoporous carbon material (MCM) with rich ether surface group was prepared from sewage sludge hydrochar using Pluronic F127 as template under pyrolysis activation, which provided an energy-efficient method to promote the resource utilization of sewage sludge as adsorbents for phenols removal from water. The MCM possessed high surface area (549 m²/g), abundant mesopores (average width 3.81 nm) and well-developed graphite structure. Acidic conditions and low temperatures favored the adsorption of phenolic compounds. The quick adsorption process of reaching over 85% of the capacity in the first 10 min and intraparticle diffusion as primary rate-limiting step were observed for all phenolic compounds. Advanced statistical physics analysis was used successfully to interpret the adsorption mechanism of phenols onto MCM and revealed a multi-molecular monolayer adsorption process primarily through negative charge-assisted hydrogen bond interaction where the ether functional group contributed to the predominant active sites. The adsorption capacity of phenolic compounds depended upon the number of molecules adsorbed per ether active site and the available density of ether bond group on the surface of MCM. 2,4,6-trichlorophenol showed a highest adsorption priority to occupy the limited ether active sites and its adsorption capacity reached 0.49 mmol/g, while p-nitrophenol exhibited a maximum number of molecules adsorbed on the single ether active site, showing an adsorption capacity of 0.42 mmol/g. The synergistic effect of multi-interactions mechanisms resulted in phenolic compounds removal with adsorption energies lower than 30 kJ/mol. This prepared MCM adsorbent is promising for application in treatment of water polluted by phenols.

Urine pretreatment significantly promotes methane production in anaerobic waste activated sludge digestion

Methane production of waste activated sludge (WAS) in anaerobic digestion is hindered due to the rate-limited hydrolysis process and the low methane potential of WAS. Pretreatment of WAS is a common and appealing strategy to improve methane production in anaerobic digestion. In this study, we proposed to use urine, an easily obtained human waste with high ammonium concentration and pH, as a novel pretreatment strategy for anaerobic WAS digestion. Urine pretreatment at levels of 5-30 % (V_urine/V_urine+WAS) could substantially enhance methane production by 5-35 % in biochemical methane potential (BMP) tests, with the highest methane production of 179.6 ± 3.3 mL/g volatile solids (VS) achieved under the highest level of urine (i.e. 30 % urine addition). Based on the model analysis, the biochemical methane potential (B₀) and hydrolysis rate of WAS (k) rose from 131.9 mL/g VS and 0.19 d^-1 in the control without pretreatment to 136.3-178.2 mL/g VS and 0.22-0.30 d^-1, respectively, after the urine pretreatment (5-30 % addition). Urine pretreatment with 5-30 % addition also improved the degradation extent (Y) of WAS by 3-35 %. The promising results indicate that urine pretreatment in anaerobic digestion is a promising technology to improve the efficiency of anaerobic digestion with environmental and economic benefits.

Strong and robust cellulose-based enzymatic membrane with gradient porous structure in dynamically catalytic removal of sulfonamides antibiotics

Enzyme membrane systems (EMS) have generated considerable interest because of their advantages of accelerating reactions, eliminating product inhibition, and enhancing conversion rates. However, there are deficiencies in the efficient fabrication of affinity carrier membranes and dynamic catalytic separation properties. Herein, a strong and highly flexible spunlaced viscose/bacterial cellulose (BC) composite membrane in situ embedded with graphene oxide (GO) was developed by combining a scalable bio-synthesis method with atom transfer radical polymerization technology. Notably, the layer-by-layer growth of BC on composite film and the addition of GO resulted in an entangled network with strong hydrogen bonding, endowing the resulting membrane with superior mechanical properties and flexibility, while facilitating a gradient structure and porous transport channels. Subsequently, a novel and highly efficient EMS was constructed by using abundant molecular brushes on composite membrane as immobilized enzyme carrier. The resulting EMS exhibited a high throughput (2.17 L/min*m²) and an interception rate (98.64%) in dynamic catalytic sulfonamide antibiotic wastewater activated with syringaldehyde mediator. Meanwhile, the removal rates of sulphapyridine and sulfamethazine were 97.20% and 94.78% under 0.14 MPa and 15 min, respectively. This efficient and scalable manufacturing strategy is of great significance and may pave a novel pathway for antibiotics wastewater treatment and recycling.

Efficient activation of peracetic acid by mixed sludge derived biochar: Critical role of persistent free radicals

Peracetic acid (PAA)-based advanced oxidation processes (AOPs) were increasingly identified as the alternative scheme in wastewater treatment. Cost-effective and easily available catalyst for activation of PAA was in urgent demand for promoting engineering application process. In this study, a new type of biochar catalyst derived from pyrolysis of mixture of primary sludge (PSD) and secondary sludge (SSD) was prepared and showed effective PAA activation ability. The degradation of p-chlorophenol (4-CP) improved with PAA activation by mixed sludge derived biochar (PS-SDBC) than secondary sludge derived biochar (S-SDBC) and primary sludge derived biochar (P-SDBC), and the highest removal efficiency achieved by PS-SDBC with the PSD/SSD ratio of 5/5 (k_obs=0.057 1/(M·min), pH 9). Correlation analysis firstly indicated that persistent free radicals (PFRs) rather than chemical composition and material structure dominated PAA activation and organic radicals (RO•) was proved to be the major reactive species through electron paramagnetic resonance (EPR) detection. The mixture of PSD and SSD caused the synergy of inorganic metals and organic matters through pyrolysis processes, resulting in larger specific surface area (SSA) (110.71 m²/g), more abundant electron-donating groups (e.g., C = O, -OH) and massive defects (I_D/I_G = 1.519) of PS-SDBC than P-SDBC and S-SDBC, which eventually promoted PFRs formation. A fascinating phenomenon was observed in PS-SDBC/PAA system that the active sites of PFRs could be regenerated by RO• attacking onto PS-SDBC, which contributed to the wide pH applicability and continuous stability of PS-SDBC/PAA system in practical wastewater treatment. This study not only significantly deepened the understanding of the reaction mechanism between PAA and biochar, but also provided a potential PAA-based AOPs for micropollutants removal in wastewater.

Treatment of faecal sludge and sewage effluent by pinewood biochar to reduce wastewater bacteria and inorganic contaminants leaching

Biochar is a valuable treatment option for faecal sludge management (FSM). However, the sanitation application rates of biochar in FSM are not well established. There is also a gap in knowledge about the effect of actual raw sewage effluent and sludge on organic and inorganic contaminants migration of biochar treated soil. This study investigated the concentration and migration rates of N, P, E. coli and faecal coliform bacteria through different soil-bed biochar column treatments leached with raw faecal sludge and sewage effluent. Forty-four soil-bed leaching columns with pinewood biochar rates at 5, 10 and 20 t/ha were set at the Bloemspruit wastewater plant, South Africa. The pinewood biochar used had a pH of 10.21, total C composition of 92%, surface area of 517 m²/g, and a pore size of 1.7 nm. It was found that the 20 t biochar per ha treatment with faecal sludge increased water retention (flows of 33 mm/h. at 0 t/ha compared to 0.8 mm/h. at 20 t/ha) and leachates purification. High detections were observed for faecal coliforms and E.coli above 4331 CFU/100 mL from the effluent and faecal sludge in soils without biochar. Detection of E.coli at 20 t/ha decreased to 1 CFU/100 mL while the faecal coliforms still had counts above 10 CFU/ 100 mL. The results showed a decreasing rate of nitrates, phosphates, zinc and copper with an increasing biochar application rate. Pinewood biochar showed significant removal efficiencies of bacteria (between 89 and 98%) and nitrates and phosphates (between 68 and 98%). Significant differences were seen at P < 0.05 between the means of the treatments with and without biochar. The results from the study show that pinewood biochar applied at rates between 5 and 20 t/ha has a high organic and inorganic contaminants reduction potential for FSM.

Antibiotic bioremediation by new generation biochar: Recent updates

The evolving multidrug resistance in microbes with increasing antibiotic pollution is becoming a severe global crisis. Recent developments on antibiotic remediations by biochar are promising. Advancements in biochar engineering enhanced biochar remediation efficiency to another level through developing new interactions and bonding abilities with antibiotic pollutants. Especially chemical/metal-composite modification significantly increased catalysis of biochar. The review's main focus is to underline biochar efficiency for the abatement of emerging antibiotic pollutants. Moreover, to relate feedstock, production conditions, and engineering techniques with biochar properties. Also, modification strategies are reviewed to obtain biochar or their composites before examining improved remediation potential ranging from 20 to 552 mg g^-1 for various antibiotics. Biochar offers different interactions depending on the surface functionalities e.g., π-π stacking, electrostatic, H-bonding, etc. Biochar and related composites have also been reviewed for remarkable properties e.g., photocatalysis, adsorption, and oxidation processes. Furthermore, future research directions and opportunities for biochar research are discussed.

Enhanced chlortetracycline removal by iron oxide modified spent coffee grounds biochar and persulfate system

Chlortetracycline (CTC) is a tetracycline derivative antibiotic that has been widely used in the livestock industry for prophylactic and therapeutic purposes. Effective measures should be taken to decrease the environmental risks associated with CTC-rich waste. Biochar produced by biomass waste showed great potential for organic contaminants removal by adsorption and catalytic degradation. This study prepared iron oxide-modified coffee grounds biochar (CGF) at different temperatures for enhanced CTC removal by adsorption and degradation. The main mechanism for CTC removal was found to be electrostatic interaction. In addition, pore diffusion, hydrogen bonds, and π-π bonds also contributed to CTC adsorption. Maximum CTC adsorption capacity was 223.63 mg/g for CGF800 (CGF prepared at 800 °C pyrolysis). The free radical content of CGF600 (CFG prepared at 600 °C pyrolysis) was higher than CGF800, and there were no significant advantages in using biochar prepared at a higher temperature for persulfate activation. The ion mass-to-charge ratio (M/z) is used to describe the ratio of mass to charge of an ion or peak, which can infer compound structure. The structure of CTC degradation products was analyzed by UPLC-MS, and the M/z values were determined as 444, 273, and 154. Thus, pyrolysis of coffee grounds at higher temperatures increased CTC adsorption capacity, and CGF can indirectly assist in CTC degradation by persulfate activation.

Unintentional release of antibiotics associated with nutrients recovery from source-separated human urine by biochar

The use of biochar to recover nitrogen and phosphorus from wastewater especially source-separated human urine is attractive from both economic and environmental standpoints. The widespread use of pharmaceuticals has raised concerns as they are not fully metabolized and ended up in human urine. The objective of this study is to examine adsorption of antibiotics (azithromycin, ciprofloxacin, sulfamethoxazole, trimethoprim, and tetracycline) and nutrients (ammonium and phosphate) in source-separated human urine by biochar and subsequent desorption. Batch adsorption experiments were conducted using biochar prepared from oak wood (OW) and paper mill sludge (PMS) to elucidate the effects of adsorption time, pH, and adsorbent dose. The desorption of adsorbed nutrients and antibiotics was also investigated. While the nutrient adsorption was more favorable by the PMS biochar, antibiotic adsorption was more prolific by the OW biochar. Hydrogen bonding and π-π interaction were identified as potential adsorption mechanisms. Experimental results agree with the Freundlich isotherm and pseudo-second order models (except the OW biochar for the kinetics). The findings suggest that biochar can adsorb both nutrients (43.30-266.67 mg g^-1) and antibiotics (246.70-389.0 μg g^-1) simultaneously. Lower solution pH (<5) was better for antibiotic adsorption, while higher solution pH (≥5) favored nutrient recovery. Also, desorption of the antibiotics (maximum of 92.6% for trimethoprim) was observed and might arise in the environment with the applications of biochar for nutrient recovery from human urine and subsequently for soil quality improvement. The findings serve as a foundation for future research on adsorption-based methods for separating nutrients and antibiotics in aqueous solutions, particularly urine.

Removal of carbamazepine (CBZ) from synthetic urine by FeOCl-coated ceramic membrane: The study of kinetic modeling

Pharmaceuticals residual in the human urine are difficult to remove in the conventional wastewater treatment plants (WWTPs) and cause a serious environmental issue. Hence, we developed a FeOCl-coated ceramic membrane coupled with the Photo-Fenton system for direct removing pharmaceuticals from human urine. In this study, the removal efficiency of CBZ from hydrolyzed urine was higher than that from fresh urine. The apparent rate constant (k_obs) of CBZ from hydrolyzed urine could reach 0.0163 min^-1, 1.39 times higher than that from fresh urine (0.0117 min^-1). Interestingly, this performance was not caused by the solution pH. The effect of substrates in the hydrolyzed urine was further explored, verifying that ammonia played a key role in quenching the hydroxyl radicals (•OH). The nitrogen reactive species (RNS) were then generated, resulting in that the k_obs of CBZ from hydrolyzed urine sharply decreased, compared with the phosphate buffer solution (pH = 9). The quenching experiment was further to confirm that the RNS was primary reactive oxide species in the hydrolyzed urine. Based on the data of kinetic study and reported previously, competitive kinetic modeling was set up, which could successfully predict the removal efficiency of pharmaceuticals from hydrolyzed urine. The study provided a new method for removing pharmaceuticals residual in human urine and the kinetic modeling could be widely used to predict the removal of pharmaceuticals from human urine.

Efficient remediation of antibiotic pollutants from the environment by innovative biochar: current updates and prospects

The increased antibiotic consumption and their improper management led to serious antibiotic pollution and its exposure to the environment develops multidrug resistance in microbes against antibiotics. The entry rate of antibiotics to the environment is much higher than its exclusion; therefore, efficient removal is a high priority to reduce the harmful impact of antibiotics on human health and the environment. Recent developments in cost-effective and efficient biochar preparation are noticeable for their effective removal. Moreover, biochar engineering advancements enhanced biochar remediation performance several folds more than in its pristine forms. Biochar engineering provides several new interactions and bonding abilities with antibiotic pollutants to increase remediation efficiency. Especially heteroatoms-doping significantly increased catalysis of biochar. The main focus of this review is to underline the crucial role of biochar in the abatement of emerging antibiotic pollutants. A detailed analysis of both native and engineered biochar is provided in this article for antibiotic remediation. There has also been discussion of how biochar properties relate to feedstock, production conditions and manufacturing technologies, and engineering techniques. It is possible to produce biochar with different surface functionalities by varying the feedstock or by modifying the pristine biochar with different chemicals and preparing composites. Subsequently, the interaction of biochar with antibiotic pollutants was compared and reviewed. Depending on the surface functionalities of biochar, they offer different types of interactions e.g., π-π stacking, electrostatic, and H-bonding to adsorb on the biochar surface. This review demonstrates how biochar and related composites have optimized for maximum removal performance by regulating key parameters. Furthermore, future research directions and opportunities for biochar research are discussed.

Biochar-based slow-release of fertilizers for sustainable agriculture: A mini review

Increasing global population and decreasing arable land pose tremendous pressures to agricultural production. The application of conventional chemical fertilizers improves agricultural production, but causes serious environmental problems and significant economic burdens. Biochar gains increasing interest as a soil amendment. Recently, more and more attentions have been paid to biochar-based slow-release of fertilizers (SRFs) due to the unique properties of biochar. This review summarizes recent advances in the development, synthesis, application, and tentative mechanism of biochar-based SRFs. The development mainly undergoes three stages: (i) soil amendment using biochar, (ii) interactions between nutrients and biochar, and (iii) biochar-based SRFs. Various methods are proposed to improve the fertilizer efficiency of biochar, majorly including in-situ pyrolysis, co-pyrolysis, impregnation, encapsulation, and granulation. Considering the distinct features of different methods, the integrated methods are promising for fabricating effective biochar-based SRFs. The in-depth understanding of the mechanism of nutrient loading and slow release is discussed based on current knowledge. Additionally, the perspectives and challenges of the potential application of biochar-based SRFs are described. Knowledge surveyed from this review indicates that applying biochar-based SRFs is a viable way of promoting sustainable agriculture.

Metabolic Mechanism of Sulfadimethoxine Biodegradation by Chlorella sp. L38 and Phaeodactylum tricornutum MASCC-0025

Antibiotic resistance is one of the most important environmental challenges. Microalgae has been considered as a promising green media for environmental purification. In this work, sulfadimethoxine (SDM) biodegradation potential of Chlorella sp. L38 and Phaeodactylum tricornutum MASCC-0025 is investigated. Experimental results indicated that the tested freshwater and marine microalgae strains presented stress response to SDM addition. For Chlorella sp. L38, it has a good adaptability to SDM condition via antioxidant enzyme secretion (SOD, MDA, and CAT up to 23.27 U/mg, 21.99 μmol/g, and 0.31 nmol/min/mg) with removal rate around 88%. P. tricornutum MASCC-0025 exhibited 100% removal of 0.5 mg/L SDM. With increasing salinity (adding a certain amount of NaCl) of cultivation media, the removal rate of SDM by microalgae increased. Although its adaptive process was slower than Chlorella sp. L38, the salinity advantage would facilitate enzyme accumulation. It indicated that microalgae could be used to remove SDM from freshwater and marine environment via suitable microalgae strain screening.

Pyrolyzing pharmaceutical sludge to biochar as an efficient adsorbent for deep removal of fluoroquinolone antibiotics from pharmaceutical wastewater: Performance and mechanism

This study explored the impact of pyrolysis parameters and modification methods on the characteristics of pharmaceutical sludge biochar, and investigated its capacity and mechanisms for levofloxacin (LEV), a typical fluoroquinolone antibiotics, adsorption. The results showed that S_BET of the biochar was improved with temperature increase, but decreased when temperature reached 900 °C. Under the optimal pyrolysis condition of 800 °C and 90 min, the biochar possessed the highest S_BET of 264.05 m² g^-1, excellent iodine value of 401.41 ± 3.84 mg∙g^-1 and phenol adsorption of 57.36 ± 3.39 mg∙g^-1. Among KOH, ZnCl₂, and CO₂ modifications, ZnCl₂ modification achieved the highest phenol adsorption of 123.40 ± 4.65 mg g^-1, with a significantly improved S_BET of 534.91 m² g^-1. The maximum LEV adsorption capacity of ZnCl₂ modified biochar, PZBC800, reached 159.26 mg g^-1, which overwhelmed the reported sludge biochars. BET, zeta potential, FT-IR, XPS, and Raman analysis, along with quantum chemistry calculation, revealed that pore filling, hydrogen bonding, π-π interaction, surface complexation, and electrostatic interaction were the main mechanisms for the excellent LEV adsorption performance of PZBC800. Deep removal (99.9%) of Fluoroquinolones (FQs) from pharmaceutical wastewater was also achieved by PZBC800 adsorption. The study promoted the development of pharmaceutical sludge biochar preparation and its application in advanced treatment of FQs pharmaceutical wastewater.

Simultaneous recovery of phosphate and degradation of antibiotics by waste sludge-derived biochar

Recovery of phosphorus (P) from wastewater has led to growing public concern considering its scarcity and future availability as well as its detrimental environmental impacts. However, the recovered P is inevitably contaminated with co-existing antibiotics like tetracycline (TC) and sulfamethazine (SMT) which will pose serious risks to the health of human and animals after being spread to the environment. In this study, we propose a novel scheme that can recover P from synthetic wastewater and at the same time degrade the co-existing antibiotics. To achieve such a goal, a series of biochar (BC) were prepared from calcination of waste sludge and were used both as the adsorbent for P recovery and as the catalyst for peroxymonosulfate (PMS) activation and antibiotic degradation. Results showed that the sludge source (i.e. S_m: municipal sludge, S_p: paper mill sludge), calcination atmosphere (i.e. air-deficient, N₂, vacuum) and temperature (i.e. 600 and 800 °C) exhibited significant influence on P adsorption capacity. Generally, the BC calcined in N₂ showed better P uptake, and increase of calcination temperature from 600 °C to 800 °C could further improve P uptake. Though BC_p-N-600 (prepared from S_p in N₂ at 600 °C) showed faster and higher P uptake (56.3 mg/g) than its counterpart BC_m-N-600 (33.2 mg/g), BC_m-N-600 showed stronger catalytic activity and more stable performance in the complex pollutant system (P + SMT). It was proposed that P was recovered primarily through the chemisorption and precipitation mechanism, while SMT was nearly completely degraded primarily by the ROS generated from PMS activation.

Insight into the activation mechanisms of biochar by boric acid and its application for the removal of sulfamethoxazole

Sulfamethoxazole (SMX) is frequently detected in the environment and causes a huge threaten to human health. Biochar (BC) is a metal-free adsorbent and generally exhibits a good adsorption capacity for SMX. However, the current activated methods usually result in the high energy consumption and low yield of the biochar. In this study, biochar was activated by boric acid under limited oxygen condition. The yield of biochar was increased by 103% after the activated by boric acid. The specific surface area of BC was significantly increased from 766.6 m²·g^-1 to 1190.6 m²·g^-1. The intensity of the (111) diamond peak of B-BC was higher than that of BC, suggesting that boric acid affected the surface pyrolysis temperature of biochar. The proposed roles of boric acid in the activation process were to: 1) enhance the generation of micropores during the pyrolysis process; 2) improve the yield of biochar via the transformation pathways of C-corresponding bonds and physical blocking. The boric acid activated biochar (B-BC) had a higher adsorption capacity for SMX than BC under the various aqueous conditions. Hence, boric acid activated biochar is a promising porous adsorbent to enhance the removal of SMX and achieve practical application.

Removal of diclofenac and oxytetracycline from synthetic urine by furfuryl alcohol-derived mesoporous carbon

In this study, using furfuryl alcohol as the precursor carbon and mesoporous silica as the template, and furfuryl alcohol-derived mesoporous carbon (FMC) was prepared. The specific surface area of FMC was 1022.61 m²/g, the pore volume was 1.71 cm³/g, and the mesoporous volume was 98.8%. Based on the adsorption kinetics of pharmaceuticals onto the FMC in synthetic urine, equilibrium adsorption was reached in 120 min, and it followed a pseudo-second-order model. The adsorption isotherms were well-fitted by the Sips isotherm model, and the saturated adsorption capacities of diclofenac and oxytetracycline in fresh urine were 411.8 mg/g and 465.9 mg/g, respectively. Batch experiment results showed that pharmaceutical removal was strongly influenced by urine components such as sodium chloride, urea, and ammonium hydroxide. The adsorption of diclofenac and oxytetracycline was influenced by many factors including π-π interactions, hydrogen bonds, and electrostatic forces. FMC exhibited excellent reusability and retained urine nutrients during pharmaceutical adsorption.

Co-oxidative removal of arsenite and tetracycline based on a heterogeneous Fenton-like reaction using iron nanoparticles-impregnated biochar

A highly efficient, eco-friendly and relatively low-cost catalyst is necessary to tackle bottlenecks in the treatment of industrial wastewater laden with heavy metals and antibiotic such as livestock farm and biogas liquids. This study investigated co-oxidative removal of arsenite (As(III)) and tetracycline (TC) by iron nanoparticles (Fe NP)-impregnated carbons based on heterogeneous Fenton-like reactions. The composites included Fe NP@biochar (BC), Fe NP@hydrochar (HC), and Fe NP@HC-derived pyrolysis char (HDPC). The functions of N and S atoms and the loading mass of the Fe NP in the Fe NP@BC in heterogeneous Fenton-like reactions were studied. To sustain its cost-effectiveness, the spent Fe NP@BC was regenerated using NaOH. Among the composites, the Fe NP@BC achieved an almost complete removal of As(III) and TC under optimized conditions (1.0 g/L of dose; 10 mM H₂O₂; pH 6; 4 h of reaction; As(III): 50 μM; TC: 50 μM). The co-oxidative removal of As(III) and TC by the Fe NP@ BC was controlled by the synergistic interactions between the Fe NPs and the active N and S sites of the BC for generating reactive oxygen species (ROS). After four consecutive regeneration cycles, about 61 and 95% of As(III) and TC removal were attained. This implies that the spent carbocatalyst still has reasonable catalytic activities for reuse. Overall, this suggests that adding technological values to unused biochar as a carbocatalyst like Fe NP@BC was promising for co-oxidative removal of As(III) and TC from contaminated water.

State of the art of urine treatment technologies: A critical review

Over the last 15 years, urine treatment technologies have developed from lab studies of a few pioneers to an interesting innovation, attracting attention from a growing number of process engineers. In this broad review, we present literature from more than a decade on biological, physical-chemical and electrochemical urine treatment processes. Like in the first review on urine treatment from 2006, we categorize the technologies according to the following objectives: stabilization, volume reduction, targeted N-recovery, targeted P-recovery, nutrient removal, sanitization, and handling of organic micropollutants. We add energy recovery as a new objective, because extensive work has been done on electrochemical energy harvesting, especially with bio-electrochemical systems. Our review reveals that biological processes are a good choice for urine stabilization. They have the advantage of little demand for chemicals and energy. Due to instabilities, however, they are not suited for bathroom applications and they cannot provide the desired volume reduction on their own. A number of physical-chemical treatment technologies are applicable at bathroom scale and can provide the necessary volume reduction, but only with a steady supply of chemicals and often with high demand for energy and maintenance. Electrochemical processes is a recent, but rapidly growing field, which could give rise to exciting technologies at bathroom scale, although energy production might only be interesting for niche applications. The review includes a qualitative assessment of all unit processes. A quantitative comparison of treatment performance was not the goal of the study and could anyway only be done for complete treatment trains. An important next step in urine technology research and development will be the combination of unit processes to set up and test robust treatment trains. We hope that the present review will help guide these efforts to accelerate the development towards a mature technology with pilot scale and eventually full-scale implementations.

Current understanding in conversion and application of tea waste biomass: A review

Along with the increasing consumption of tea and its extracts, the amount of tea waste grows rapidly, which not only results in huge biomass loss, but also increases environmental stress. In past years, interest has been attracted on utilization of tea waste biomass, and a lot of work has been carried out. This review summarized the progress in conversion of tea waste by thermo-chemical and biological technologies and analyzed the property of the derived products and their performance in applications. It was found that biochar derived from tea waste had relatively large surface area, porous structures, and abundant functional groups, and could be used as bio-adsorbents and catalysts and electrochemical energy storage, while the cost of its largescale production should be evaluated. Profoundly, biological conversion, including ensiling and composting, was suggested to be an effective way to develop the tea waste biomass in practice due to its low-cost and specific functions.

Removal of pharmaceuticals from nitrified urine

In this study, granular activated carbon (GAC) was examined for the removal of five of the most commonly detected pharmaceuticals (naproxen, carbamazepine, acetaminophen, ibuprofen and metronidazole) from a nitrified urine to make the urine-derived fertiliser nutrient safe for food crops. Batch experiments were conducted to investigate the adsorption kinetics that described the removal of micropollutants (equal concentrations of 0.2 mM) from the synthetic nitrified urine at different GAC dosages (10-3000 mg/L). Artificial neural network modelling was also used to predict and simulate the removal of pharmaceuticals from nitrified urine. Langmuir and Freundlich isotherm models described the equilibrium data, with the Langmuir model providing slightly higher correlations. At the highest dose of 3000 mg/L GAC, all the pharmaceuticals showed a removal rates of over 90% after 1 h of adsorption time and 99% removal rates after 6 h of adsorption time. This study concludes that GAC is able to remove the targeted xenobiotics without affecting the concentration of N and P in the urine, suggesting that nitrified urine could be safely used as a nutrient product in future.

Synergistic adsorption and degradation of sulfamethoxazole from synthetic urine by hickory-sawdust-derived biochar: The critical role of the aromatic structure

This study investigated the adsorptive removal and subsequent degradation of sulfamethoxazole (SMX) from a synthetic urine by biochar (BC). The BCs used in this study were prepared using two different feedstocks with different temperatures. Element analysis and Fourier transform infrared spectroscopy (FTIR) results suggested that the aromaticity of one of the BCs, 700HSBC was significantly different from the 700PSBC although both of them were prepared at the same temperature (700 °C) with similar pore size distributions and specific surface areas. Due to the presence of abundant aromatic structures, 700HSBC showed a higher SMX uptake than 700PSBC, suggesting that the π-π interaction was the main adsorption mechanism. The removal of SMX from the urine was significantly enhanced by adding hydrogen peroxide to the 700HSBC. The carbonate radicals degradation of SMX mechanism was proposed and verified. With 700HSBC having abundant aromatic structures acting as π-electron donors, it could be an efficient activator for peroxymonocarbonate (HCO₄^-) to generate carbonate radicals. Hence, it could be concluded that the aromatic structures on BCs play a key role in both of the adsorption and hydrogen peroxide degradation of the SMX resulting in its removal from urine.

Abiotic transformation and ecotoxicity change of sulfonamide antibiotics in environmental and water treatment processes: A critical review

Sulfonamides (SAs) are among the most widely used antibiotics to treat bacterial infections for humans and animals. They are also used in livestock agriculture to improve growth and feed efficiency in many countries. Recent years, there is a growing concern about the environmental fate and treatment technologies of SAs, in order to eliminate their potential impact on the ecosystem and human health. Additionally, SAs are frequently used as model compounds to evaluate the performance of newly developed advanced water treatment processes. Hence, understanding the chemical reaction features of SAs can provide valuable information for further technological development. In this review, the reaction kinetics, abiotic transformations and corresponding ecotoxicity changes of SAs in natural environments and water treatment processes were comprehensively analyzed to draw critical suggestion and new insights. The •OH-based AOP is proposed as an effective method for the elimination of SAs toxicity, although it is susceptible to water constituent due to low selectivity. The application of biochar or metal-based oxidants in AOPs is becoming a future trend for SA treatment. Overall, this review would provide useful information for the development of advanced water treatment technologies and the control of ecological risks related to SAs.

Iron-carbon microelectrolysis for wastewater remediation: Preparation, performance and interaction mechanisms

Rapid industrialization and urbanization have produced a lot of hazardous substances in water and wastewater, which has turned into a crucial issue to the environment and the public health. Recently, iron carbon microelectrolysis (IC-ME) has attracted extensive attention in environmental remediation due to its low costs and excellent performance. Nevertheless, there is still a lack of a more systematic review on IC-ME preparation methods, their performance, and the interaction mechanisms of IC-ME in the remediation of wastewater. Herein, this work summarizes the synthetic methods, application of IC-ME materials, and the mechanism of pollutant removal by IC-ME. A variety approaches have been applied to prepare IC-ME materials, and the preparation methods and conditions have a certain influence on the properties of IC-ME materials, thus affecting the performance of pollutant removal. The mechanisms of IC-ME for contaminants removal are very complex, including adsorption, coprecipitation, reduction, surface complexation, and oxidation. Moreover, research vacant fields and problems that existed in the application of IC-ME are proposed. At last, the problems to be addressed to adapt IC to future applications are introduced. This paper reviews and prospects IC-ME wastewater remediation technology, which provides a reference for further scientific research and engineering applications.

Synergistic catalytic Fenton-like degradation of sulfanilamide by biosynthesized goethite-reduced graphene oxide composite

A series of goethite (Gt)-graphene (rGO) composites (Gt-rGO) having different rGO contents (2%-10%) was biologically prepared under mild conditions with Acidovorax sp. BoFeN1 and exhibited comparable or even higher catalytic efficiencies upon sulfonamides degradation than most known chemically synthesized catalysts. Pseudo-first-order rate constant of sulfanilamide degradation (60 μM, 0.971 h^-1) in the system mediated by Gt-rGO with the optimal rGO content of 6% was 6.7, 15.4 and 168.1 folds higher than those in the control rGO/H₂O₂, Gt/H₂O₂ and H₂O₂ systems, respectively. Excellent synergistic catalytic effects between Gt and rGO in Gt-rGO were identified in four continuous cycles. The Gt-rGO systems exhibited more efficient •OH generation, H₂O₂ decomposition and Fe(II) accumulation rates than the control Gt or rGO systems. Fast Fe(III)/Fe(II) cycling was obtained in the Gt-rGO systems, which might be due to the strong Fe-C coordination and the decrease of rGO aggregation and Gt particle sizes. Additionally, Gt particles in Gt-rGO exposed more defects as active sites for H₂O₂ activation. High-performance liquid chromatography-mass spectrometer analysis suggested that sulfanilamide was gradually degraded through hydroxylation, C-N cleavage and benzene ring opening. The results provided a new approach for the tailored design of eco-friendly, cost-effective and efficient iron (oxyhydr)oxides-graphene catalysts for contaminants elimination.

Application of percarbonate and peroxymonocarbonate in decontamination technologies

Sodium percarbonate (SPC) and peroxymonocarbonate (PMC) have been widely used in modified Fenton reactions because of their multiple superior features, such as a wide pH range and environmental friendliness. This broad review is intended to provide the fundamental information, status and progress of SPC and PMC based decontamination technologies according to the peer-reviewed papers in the last two decades. Both SPC and PMC can directly decompose various pollutants. The degradation efficiency will be enhanced and the target contaminants will be expanded after the activation of SPC and PMC. The most commonly used catalysts for SPC activation are iron compounds while cobalt compositions are applied to activate PMC in homogenous and heterogeneous catalytical systems. The generation and participation of hydroxyl, superoxide and/or carbonate radicals are involved in the activated SPC and PMC system. The reductive radicals, such as carbon dioxide and hydroxyethyl radicals, can be generated when formic acid or methanol is added in the Fe(II)/SPC system, which can reduce target contaminants. SPC can also be activated by energy, tetraacetylethylenediamine, ozone and buffered alkaline to generate different reactive radicals for pollutant decomposition. The SPC and activated SPC have been assessed for application in-situ chemical oxidation and sludge dewatering treatment. The challenges and prospects of SPC and PMC based decontamination technologies are also addressed in the last section.

One-Pot Synthesis of Nano CuO-ZnO Modified Hydrochar Derived from Chitosan and Starch for the H2S Conversion

A novel kind of hydrochar adsorbent, modified by CuO-ZnO and derived from chitosan or starch, was synthesized for H2S adsorption. The prepared adsorbent was characterized by BET, XRD, EDX, SEM, and XPS. The results showed that the modified hydrochar contained many amino groups as functional groups, and the nanometer metal oxide particles had good dispersion on the surface of the hydrochar. The maximum sulfur capacity reached 28.06 mg/g-adsorbent under the optimized conditions. The amine group significantly reduced the activation energy between H2S and CuO-ZnO conducive to the rapid diffusion of H2S among the lattices. Simultaneously, cationic polyacrylamide as a steric stabilizer could change the formation process of CuO and ZnO nanoparticles, which made the particle size smaller, enabling them to react with H2S sufficiently easily. This modified hydrochar derived from both chitosan and starch could be a promising adsorbent for H2S removal.

Selective oxidation of pharmaceuticals and suppression of perchlorate formation during electrolysis of fresh human urine

Urine comprises only a small (~1%) volumetric fraction of municipal wastewater, but represents a dominant source of pharmaceuticals, many of which may pass through conventional wastewater treatment and pose risks to aquatic ecosystems. Point-source treatment of source-separated urine presents a unique opportunity to degrade pharmaceuticals before dilution with wastewater, and electrochemical advanced oxidation processes are one increasingly investigated option. However, they often lead to the formation of oxidation byproducts including chlorate, perchlorate at very high concentrations. Here, we show that the high urea content of fresh human urine suppresses the formation of oxychlorides by inhibiting formation of HOCl/OCl^‒ during electrolysis, while still enabling pharmaceutical degradation due to the slow rate of urea oxidation by ^•OH. This results in improved performance compared to equivalent treatment of hydrolyzed aged urine. This electrochemical oxidation scheme is shown to degrade the model contaminants cyclophosphamide and sulfamethoxazole with surface-area-to-volume-normalized pseudo-first-order rate constants greater than 0.08 cm/min in authentic fresh human urine. It results in ~100 × decrease in pharmaceutical concentrations in 2 h while generating ~1000 × lower oxychloride byproduct concentrations in synthetic fresh urine than synthetic hydrolyzed aged urine matrixes. Importantly, this proof-of-principle shows that simple and safe electrochemical methods can be used for point-source-remediation of pharmaceuticals in fresh human urine (before storage and hydrolysis), without formation of significant oxychloride byproducts.

Coupling experiments with calculations to understand the thermodynamics evolution for the sorption of zwitterionic ciprofloxacin on oxidizing-aged pyrogenic chars in the aquatic system

Oxidized aging due to the long-term exposure can significantly alter the sorption of pyrogenic chars (i.e., biochar, BC) towards antibiotics, which determined their fates in natural environments. In this study, the sorption of ciprofloxacin (CIP) on the oxidizing-aged BCs was studied linking the experimental thermodynamics and theoretical calculations. Results revealed that Q₀ of CIP negatively correlated with their average site energies (E_m), while pore-normalized Q₀ on aged BCs were 2-6 folds higher than fresh BCs. From competitive sorption, it is proposed that the transformation of CIP^± to CIP⁺ occurred and the π⁺-π electron donor-acceptor interaction and Coulombic attraction onto the aged BCs played a critical role. These two specific interactions with CIP were thermodynamically improved when aging degree increased and favored the free energies (Δ_aG) of sorption by 2-5 kJ mol^-1. Based on the identified relationship between experimental Δ_OA-ΔG⁰ with E_a through DFT calculations, the contributions of the specific interactions to antibiotic sorption on aged BCs were quantified. This study provided an in-depth understanding of how the aging process affects the sorption of zwitterionic antibiotics on BCs and also possibilities to predict the fate of antibiotics in the presence of BCs over a long-term period.

Sorption of Sulfamethoxazole on Inorganic Acid Solution-Etched Biochar Derived from Alfalfa

The properties of alfalfa-derived biochars etched with phosphoric (PBC) or hydrochloric acid (ClBC) compared with raw materials (BC) were examine in this paper. SEM, FT-IR, XRD, BET and elemental analysis were performed to characterize the micromorphology and chemical structure comprehensibly. The results showed that the porous structure was enhanced, and surface area was increased via etching with inorganic acids. Batch adsorption experiments were performed for sulfamethoxazole (SMX) to biochars. The experimental data showed that modified biochars exhibited higher adsorption capacity for SMX, i.e., the adsorption quantity of ClBC and PBC had risen by 38% and 46%. The impact on pH values suggested that the physisorption, including pore-filling and electrostatic interaction, might be applied to original biochar. In addition, chemisorption also played a role, including hydrogen bonding, π-π electron donor acceptor interaction (π-π EDA), and so on. Furthermore, both pH and coexisting ions also had a certain effect on sorption. Enhancement of the electrostatic attraction between biochar and SMX might also account for the enhanced capacity of SMX at pH < 7, and coexisting ions could decrease the amount of SMX adsorbed onto biochars, mainly because of competition for adsorption sites.

Adsorption of emerging contaminants from water and wastewater by modified biochar: A review

Emerging contaminants (ECs), a group of relatively low-concentration but high-toxicity pollutants in the environment, have attracted widespread attention in recent years. These trace pollutants can be enriched in organisms and finally transferred to human bodies, posing a potential hazard to public health. Biochar, a low-cost and high-efficiency adsorbent, has been used to treat ECs in water. However, due to certain limitations of pristine biochar, such as poor adsorption capacity, narrow adsorption range, and other shortcomings, it is necessary to modify biochar to improve its applications in water treatment for ECs. Currently, there are a lot of reports on the removal of ECs from water by modified biochar. These studies explored different modification methods to functionalize biochar with various physicochemical properties, which resulted in distinct adsorption effects, behaviors and mechanisms of modified biochar on different ECs. There is a need to systematically review and digest the knowledge on the adsorption of ECs on modified biochar. In this review, recent biochar modification methods used in ECs removal are firstly summarized, and the adsorption performance and mechanisms of modified biochar on typical ECs are then systematically reviewed. Finally, the main research directions and trends, as well as recommendations and suggestions for future development are pointed out.

Goethite dispersed corn straw-derived biochar for phosphate recovery from synthetic urine and its potential as a slow-release fertilizer

In this study, goethiete (α-FeOOH) -biochar (BC) composites were successfully developed from a co-precipitation reaction under alkaline conditions (pH = 11.93) and used as the adsorbent for phosphate recovery from urine. The morphology and crystallinity of α-FeOOH-BC composites were characterized by scanning electron microscopy and X-ray diffraction. α-FeOOH loaded BC was found to be amorphous. This may be caused by the Si residue in BC. The Elovich model and the Langmuir model fit better to the kinetic and isotherm results of α-FeOOH-600BC, respectively, indicating that phosphate adsorption is mainly a chemisorption and monolayer adsorption process. The α-FeOOH-600BC with amorphous structure showed higher adsorption capacity than crystalline α-FeOOH, and the maximum phosphate sorption capacity reached 57.39 mg g^-1. Additionally, the extractable phosphate of this material was approximately 967.5 mg P·kg^-1 suggesting the α-FeOOH-600BC after adsorption could be a promising alternative as a slow-phosphate-release fertilizer. Fourier-transform infrared and X-ray induced photoelectron spectroscopy results showed that the active sites of the adsorption of phosphate were the Fe-OH bonds that formed inner-sphere complexes (Fe-O-P).