Evaluation of a biological post-treatment after full-scale ozonation at a municipal wastewater treatment plant

The Dicentrarchus labrax estrogen screen test: A relevant tool to screen estrogen-like endocrine disrupting chemicals in the aquatic environment

In response to the need for the diversification of regulatory bioassays to screen estrogen-like endocrine disrupting chemical (EEDC) in the environment, we propose the use of a reporter gene assay involving all nuclear estrogen receptors from Dicentrarchus labrax (i.e., sbEsr1, sbEsr2a, or sbEsr2b). Named DLES test (D. labrax estrogen screen), it aims at complementing existing standardized in vitro tests by implementing more estrogen receptors notably those that do not originate from humans. Positive responses were obtained with all three estrogen receptors, and-consistently with observations from other species-variations in sensitivity to E2 were measured. Sensitivity and EC50 values could be classified as follows: sbEsr2b < sbEsr2a < sbEsr1. The pharmacological characterization with a human estrogen receptor antagonist (fulvestrant) successfully validated the specific involvement of each sbEsr and evidenced the capacity of the DLES test to highlight antagonist interactions. The DLES test was applied to WWTP contaminant extracts. A positive response was detected in the inflow sample in accordance with the YES test, but not in the outflow sample. Notwithstanding, the DLES test (sbEsr2b) exhibited greater sensitivity for the screening of those samples. This study demonstrates the need for more comprehensive testing including representatives of marine species for a better detection of EEDCs. The DLES test appears as a pertinent tool to predict adverse effects and to widen the scope of screening and hazard assessment of EEDCs in the environment.

An Integrated Approach of Bioassays and Non-Target Screening for the Assessment of Endocrine-Disrupting Activities in Tap Water and Identification of Novel Endocrine-Disrupting Chemicals

The safety of drinking water is a significant environmental issue of great concern for human health since numerous contaminants are often detected in drinking water and its sources. Boiling is a common household method used to produce relatively high-quality drinking water in some countries and regions. In this study, with the aid of an integrated approach of in vitro bioassays and non-target analysis based on high-resolution mass spectrometry coupled with liquid chromatography, alterations in endocrine-disrupting activities in tap water samples without and with boiling were revealed, as well as the potential endocrine-disrupting chemicals (EDCs) contributing to these alterations were identified. The organic extracts of tap water had no significant (ant)agonistic activities against an estrogen receptor (ER), progesterone receptor (PR), glucocorticoid receptor (GR), and mineralocorticoid receptor (MR) at enrichment concentrations of ≤10 times, posing no immediate or acute health risk to humans. However, the presence of agonistic activities against PR and MR and antagonistic activities against ER, PR, GR, and MR in OEs of tap water at relatively higher enrichment concentrations still raise potential health concerns. Boiling effectively reduced antagonistic activities against these steroid hormone receptors (SHRs) but increased estrogenic and glucocorticoid activities in drinking water. Four novel potential EDCs, including one UV filter (phenylbenzimidazole sulfonic acid, PBSA) and three natural metabolites of organisms (beta-hydroxymyristic acid, 12-hydroxyoctadecanoic acid, and isorosmanol) were identified in drinking water samples, each of which showed (ant)agonistic activities against different SHRs. Given the widespread use of UV filters in sunscreens to prevent skin cancer, the health risks posed by PBSA as an identified novel EDC are of concern. Although boiling has been thought to reduce the health risk of drinking water contamination, our findings suggest that boiling may have a more complex effect on the endocrine-disrupting activities of drinking water and, therefore, a more comprehensive assessment is needed.

Ozonation products of purine derivatives, the basic structures of antiviral micropollutants

Purine and its nucleobases adenine and guanine are the basic structures of a large group of antiviral agents such as acyclovir and penciclovir. Hence, their ozonation is of interest with regard to wastewater treatment due to the formation of products that could affect the aquatic environment. In this study, the transformation products of the mentioned substances are investigated under different defined reaction conditions in order to gain insight into the ozonation characteristics of this compound class. Results show that examining related molecules significantly improves product screening by compiling known products and analogues leading to comprehensive candidate lists, for the purines with a total number of >120 candidates (including possible duplicates for several purines) of which 49 were detected for the derivatives studied. One product, cyanuric acid, which was previously postulated for adenine, was tentatively confirmed and quantified for the first time for the reaction of purine and adenine with ozone. In addition, two prioritisation approaches are presented to identify the major products that are either formed under specific reaction conditions or are potentially relevant for structurally related pollutants. First, principal component analysis allowed the prioritisation of the products formed according to reaction conditions. In the analysis of guanine and the two antivirals, this approach showed that at neutral and basic pH the 2-imino-5-oxoimidazoline products dominated while at acidic pH either analogues of 5-amino-2,4-imidazolidinedione or 2,4-diamino-1,3-oxazol-5-(2H)-one were abundant. A second approach prioritising common products in the ozonation of all three basic structures revealed the formation of two products that had not been reported before: C4H8O3 and C3H2N2O3, presumably oxalylurea. Both molecules or their analogues may also be formed from related micropollutants. Overall, examining basic structures and exemplary micropollutants in combination was shown to be a worthwhile approach to gain knowledge on the ozonation of a whole range of compounds.

Wastewater from natural gas Cansolv desulfurization process: Comprehensive characterization and effective removal of organic compounds

The wastewater generated by the solvent amine desulfurization process in natural gas purification plants is characterized by its recalcitrant organic compounds and high salinity. Without effective treatment, it has the potential to inflict severe environmental harm. The composition of organic matter, however, exerts a profound influence on the outcomes of oxidation processes. To rectify the limitations associated with indiscriminate oxidation that yields suboptimal results, this investigation meticulously performed a molecular-level analysis of organic matter. Based on the organic matter composition in the influent, this study compared the treatment efficacy of three oxidation processes and determined O3/H2O2-Fenton as the optimal joint approach. After O3/H2O2 oxidation, long-chain unsaturated organic compounds (C > 40,DBE > 20) underwent degradation into short-chain aldehydes and low-molecular-weight fatty acids, with priority given to reactions involving CC, CO, and OH over CH reactions. Subsequent Fenton oxidation effectively removed the refractory organics (CHOS, CHONS) and significantly reduced the diversity of organic matter (from 7730 to 4237). The carboxylation, demethylation, and dehydrogenation reactions further facilitated the removal of recalcitrant organic compounds. In light of these findings, this study substantiates that the conversion of extended-chain unsaturated compounds into abbreviated-chain saturated compounds within the system through O3/H2O2 oxidation significantly enhances the subsequent efficacy of Fenton oxidation in organic matter removal. These insights offer valuable perspectives for the efficient remediation of analogous high-salinity organic wastewater scenarios.

Non-target analysis for water characterization: wastewater treatment impact and selection of relevant features

Non-target analyses were conducted to characterize and compare the molecular profiles (UHPLC-HRMS fingerprint) of water samples from a wastewater treatment plant (WWTP). Inlet and outlet samples were collected from three campaigns spaced 6 months apart in order to highlight common trends. A significant impact of the treatment on the sample fingerprints was shown, with a 65-70% abatement of the number of features detected in the effluent, and more polar, smaller and less intense molecules found overall compared to those in WWTP influent waters. Multivariate analysis (PCA) associated with variations of the features between inlets and outlets showed that features appearing or increasing were correlated with effluents while those disappearing or decreasing were correlated with influents. Finally, effluent features considered as relevant to a potentially adverse effect on aqueous media (i.e. those which appeared or increased or slightly varied from the influent) were highlighted. Three hundred seventy-five features common with the 3 campaigns were thus selected and further characterized. For most of them, elementary composition was found to be C, H, N, O (42%) and C, H, N, O, P (18%). Considering the MS2 spectra and several reference MS2 databases, annotations were proposed for 35 of these relevant features. They include synthetic products, pharmaceuticals and metabolites.

Exploring the efficacy of metabarcoding and non-target screening for detecting treated wastewater

Wastewater treatment processes can eliminate many pollutants, yet remainder pollutants contain organic compounds and microorganisms released into ecosystems. These remainder pollutants have the potential to adversely impact downstream ecosystem processes, but their presence is currently not being monitored. This study was set out with the aim of investigating the effectiveness and sensitivity of non-target screening of chemical compounds, 18S V9 rRNA gene, and full-length 16S rRNA gene metabarcoding techniques for detecting treated wastewater in receiving waters. We aimed at assessing the impact of introducing 33 % treated wastewater into a triplicated large-scale mesocosm setup during a 10-day exposure period. Discharge of treated wastewater significantly altered the chemical signature as well as the microeukaryotic and prokaryotic diversity of the mesocosms. Non-target screening, 18S V9 rRNA gene, and full-length 16S rRNA gene metabarcoding detected these changes with significant covariation of the detected pattern between methods. The 18S V9 rRNA gene metabarcoding exhibited superior sensitivity immediately following the introduction of treated wastewater and remained one of the top-performing methods throughout the study. Full-length 16S rRNA gene metabarcoding demonstrated sensitivity only in the initial hour, but became insignificant thereafter. The non-target screening approach was effective throughout the experiment and in contrast to the metabarcoding methods the signal to noise ratio remained similar during the experiment resulting in an increasing relative strength of this method. Based on our findings, we conclude that all methods employed for monitoring environmental disturbances from various sources are suitable. The distinguishing factor of these methods is their ability to detect unknown pollutants and organisms, which sets them apart from previously utilized approaches and allows for a more comprehensive perspective. Given their diverse strengths, particularly in terms of temporal resolution, these methods are best suited as complementary approaches.

Hazardous radical-coupled transformation products of benzophenone-3 formed during manganese dioxide treatment

Radical-coupled transformation products (TPs) have been identified as the byproducts of various transformation processes, including both natural attenuation and artificial treatments, of phenolic micropollutants. Benzophenone-3 (BP-3), an organic UV filter of emerging concern, has been previously reported with ubiquitous occurrence in the natural environment and water bodies. Current research has demonstrated how TPs are formed from BP-3 when it is treated with manganese oxide (MnO2). The ecological and toxicological risks of these TPs have also been assessed. Polymerization of BP-3 through radical coupling was observed as the major pathway by which BP-3 is transformed when treated with MnO2. These radical-coupled TPs haven't shown further degradation after formation, suggesting their potential persistence once occurred in the environment. In silico experiments predict the radical-coupled TPs will increase in mobility, persistence and ecotoxicity. If true, they also represent an ever-increasing threat to the environment, ecosystems and, most immediately, aquatic living organisms. In addition, radical-coupled TPs produced by MnO2 transformation of BP-3 have shown escalated estrogenic activity compared to the parent compound. This suggests that radical coupling amplifies the toxicological impacts of parent compound. These results provide strong evidence that radical-coupled TPs with larger molecular sizes are having potential adverse impacts on the ecosystem and biota.

A critical review on quantitative evaluation of aqueous toxicity in water quality assessment

Conventional chemical techniques have inherent limitations in detecting unknown chemical substances in water. As a result, effect-based methods have emerged as a viable alternative to overcome these limitations. These methods provide more accurate and intuitive evaluations of the toxic effects of water. While numerous studies have been conducted, only a few have been applied to national water quality monitoring. Therefore, it is crucial to develop toxicity evaluation methods and establish thresholds based on quantifying toxicity. This article provides an overview of the development and application of bioanalytical tools, including in vitro and in vivo bioassays. The available methods for quantifying toxicity are then summarized. These methods include aquatic life criteria for assessing the toxicity of a single compound, comprehensive wastewater toxicity testing for all contaminants in a water sample (toxicity units, whole effluent toxicity, the potential ecotoxic effects probe, the potential toxicology method, and the lowest ineffective dilution), methods based on mechanisms and relative toxicity ratios for substances with the same mode of action (the toxicity equivalency factors, toxic equivalents, bioanalytical equivalents), and effect-based trigger values for micropollutants. The article also highlights the advantages and disadvantages of each method. Finally, it proposes potential areas for applying toxicity quantification methods and offers insights into future research directions. This review emphasizes the significance of enhancing the evaluation methods for assessing aqueous toxicity in water quality assessment.

Effect-Targeted Mapping of Potential Estrogenic Agonists and Antagonists in Wastewater via a Conformation-Specific Reporter-Mediated Biosensor

Wastewater treatment plants (WWTPs) are regarded as the main sources of estrogens that reach the aquatic environment. Hence, continuous monitoring of potential estrogenic-active compounds by a biosensor is an appealing approach. However, existing biosensors cannot simultaneously distinguish and quantify estrogenic agonists and antagonists. To overcome the challenge, we developed an estrogen receptor-based biosensor that selectively screened estrogenic agonists and antagonists by introducing rationally designed agonist/antagonist conformation-specific reporters. The double functional conformation-specific reporters consist of a Cy5.5-labeled streptavidin moiety and a peptide moiety, serving as signal recognition and signal transduction elements. In addition, the conformation recognition mechanism was further validated at the molecular level through molecular docking. Based on the two-step "turn-off" strategy, the biosensor exhibited remarkable sensitivity, detecting 17β-estradiol-binding activity equivalent (E2-BAE) at 7 ng/L and 4-hydroxytamoxifen-binding activity equivalent (4-OHT-BAE) at 91 ng/L. To validate its practicality, the biosensor was employed in a case study involving wastewater samples from two full-scale WWTPs across different treatment stages to map their estrogenic agonist and antagonist binding activities. Comparison with the yeast two-hybrid bioassay showed a strong liner relationship (r2 = 0.991, p < 0.0001), indicating the excellent accuracy and reliability of this technology in real applications.

Removal of micropollutants and ecotoxicity during combined biological activated carbon and ozone (BO3) treatment

Ozonation is a viable option to improve the removal of micropollutants (MPs) in wastewater treatment plants (WWTPs). Nevertheless, the application of ozonation is hindered by its high energy requirements and by the uncertainties regarding the formation of toxic transformation products in the process. Energy requirements of ozonation can be reduced with a pre-ozone treatment, such as a biological activated carbon (BAC) filter, that removes part of the effluent organic matter before ozonation. This study investigated a combination of BAC filtration followed by ozonation (the BO3 process) to remove MPs at low ozone doses and low energy input, and focused on the formation of toxic organic and inorganic products during ozonation. Effluent from a WWTP was collected, spiked with MPs (approximately 1 µg/L) and treated with the BO3 process. Different flowrates (0.25-4 L/h) and specific ozone doses (0.2-0.6 g O3/g TOC) were tested and MPs, ecotoxicity and bromate were analyzed. For ecotoxicity assessment, three in vivo (daphnia, algae and bacteria) and six in vitro CALUX assays (Era, GR, PAH, P53, PR, andNrf2 CALUX) were used. Results show that the combination of BAC filtration and ozonation has higher MP removal and higher ecotoxicity removal than only BAC filtration and only ozonation. The in vivo assays show a low ecotoxicity in the initial WWTP effluent samples and no clear trend with increasing ozone doses, while most of the in vitro assays show a decrease in ecotoxicity with increasing ozone dose. This suggests that for the tested bioassays, feed water and ozone doses, the overall ecotoxicity of the formed transformation products during ozonation was lower than the overall ecotoxicity of the parent compounds. In the experiments with bromide spiking, relevant formation of bromate was observed above specific ozone doses of approximately 0.4 O3/g TOC and more bromate was formed for the samples with BAC pre-treatment. This indirectly indicates the effectivity of the pre-treatment in removing organic matter and making ozone more available to react with other compounds (such as MPs, but also bromide), but also underlines the importance of controlling the ozone dose to be below the threshold to avoid formation of bromate. It was concluded that treatment of the tested WWTP effluent in the BO3 process at a specific ozone dose of 0.2 g O3/g TOC, results in high MP removal at limited energy input while no increase in ecotoxicity, nor formation of bromate was observed under this condition. This indicates that the hybrid BO3 process can be implemented to remove MPs and improve the ecological quality of this WWTP effluent with a lower energy demand than conventional MP removal processes such as standalone ozonation.

Novel nontarget LC-HRMS-based approaches for evaluation of drinking water treatment

A conventional evaluation methodology for drinking water pollution focuses on analysing hundreds of compounds, usually by liquid chromatography-tandem mass spectrometry. High-resolution mass spectrometry allows comprehensive evaluation of all detected signals (compounds) based on their elemental composition, intensity, and numbers. We combined target analysis of 192 emerging micropollutants with nontarget (NT) full-scan/MS/MS methods to describe the impact of treatment steps in detail and assess drinking water treatment efficiency without compound identification. The removal efficiency based on target analytes ranged from - 143 to 97%, depending on the treatment section, technologies, and season. The same effect calculated for all signals detected in raw water by the NT method ranged between 19 and 65%. Ozonation increased the removal of micropollutants from the raw water but simultaneously caused the formation of new compounds. Moreover, ozonation byproducts showed higher persistence than products formed during other types of treatment. We evaluated chlorinated and brominated organics detected by specific isotopic patterns within the developed workflow. These compounds indicated anthropogenic raw water pollution but also potential treatment byproducts. We could match some of these compounds with libraries available in the software. We can conclude that passive sampling combined with nontargeted analysis shows to be a promising approach for water treatment control, especially for long-term monitoring of changes in technology lines because passive sampling dramatically reduces the number of samples and provides time-weighted average information for 2 to 4 weeks.

Advanced oxidation processes for removal of monocyclic aromatic hydrocarbon from water: Effects of O3/H2O2 and UV/H2O2 treatment on product formation and biological post-treatment

Several oxidative treatment technologies, such as ozonation or Fenton reaction, have been studied and applied to remove monocyclic hydroaromatic carbon from water. Despite decades of application, little seems to be known about formation of transformation products while employing different ozone- or ^∙OH-based treatment methods and their fate in biodegradation. In this study, we demonstrate that O₃/H₂O₂ treatment of benzene, toluene, ethylbenzene (BTE), and benzoic acid (BA) leads to less hydroxylated aromatic transformation products compared to UV/H₂O₂ as reference system - this at a similar ^∙OH exposure and parent compound removal efficiency. Aerobic biodegradation tests after oxidation of 0.15 mM BA (12.6 mg C L^-1 theoretical DOC) revealed that a less biodegradable DOC fraction > 4 mg C L^-1 was formed in both oxidative treatments compared to the BA control. No advantage of ozonation over UV/H₂O₂ treatment was observed in terms of mineralization capabilities, however, we detected less transformation products after oxidation and biodegradation using high-resolution mass spectrometry. Biodegradation of BA that was not oxidized was more complete with minimal organic residual. Overall, the study provides new insights into the oxidation of monocyclic aromatics and raises questions regarding the biodegradability of oxidation products, which is relevant for several treatment applications.

Effect of solar radiation on natural organic matter composition in surface waters and resulting impacts on drinking water treatment

Solar radiation experiments showed a shift in the composition of natural organic matter (NOM). Due to irradiation, the concentration of high molecular weight (HMW) molecules decreased, and that of the low molecular weight (LMW) fraction increased. Microbiological analyses showed that biodegradation was neglectable. To assess the consequences for water treatment processes, coagulation jar tests were performed by comparing the removal effectivity for NOM fractions from irradiated and unirradiated raw water. The degree of dissolved organic carbon (DOC) removal by coagulation was lower for irradiated waters. As primarily HMW organic compounds are removed by coagulation, the decrease in coagulation performance is attributed to the increase in the LMW concentration due to photochemical reactions induced by solar radiation. Flocs were about 15% larger for irradiated water. Possibilities to adapt water treatment to respond to changes in DOC composition and concentration are outlined. Ozonation-biofiltration is judged as the most promising treatment process to cope with climate change-related challenges in drinking water treatment.

Use of wood and cork in biofilters for the simultaneous removal of nitrates and pesticides from groundwater

About 13% and 7% of monitored groundwater stations in Europe exceed the permitted levels of nitrates (50 mg NO₃^- L^-1) or pesticides (0.1 μg L^-1), respectively. Although slow sand filtration can remove nitrates via denitrification when oxygen is limited, it requires an organic carbon source. The present study evaluates the performance of the use of wood pellets and granulated cork as carbon sources in bench-scale biofilters operated under water-saturated and water-unsaturated conditions for more than 400 days. The biofilters were monitored for nitrate (200 mg L^-1) and pesticide (mecoprop, diuron, atrazine, and bromacil, each at a concentration of 5 μg L^-1) attenuation, as well as for the formation of nitrite and pesticide transformation products. Microbiological characterization of each biofilter was also performed. The water-saturated wood biofilter achieved the best nitrate removal (>99%), while the cork biofilters lost all denitrification power over time (from 38% to no removal). The unsaturated biofilter columns were not effective for removing nitrates (20-30% removal). As for pesticides, all the biofilters achieved high removal rates of mecoprop and diuron (>99% and >75%, respectively). Atrazine removal was better in the wood-pellet biofilters than the cork ones (68-96% vs. 31-38%). Bromacil was only removed in the water-unsaturated cork biofilter (67%). However, a bromacil transformation product was formed there. The water-saturated wood biofilter contained the highest number of denitrifying microorganisms, with Methyloversatilis as the characteristic genus. Microbial composition could explain the high removal of pesticides and nitrates achieved in the wood-pellet biofilter. Overall, the results indicate that wood-pellet biofilters operated under water-saturated conditions are a good solution for treating groundwater contaminated with nitrates and pesticides.

Microbial communities and processes in biofilters for post-treatment of ozonated wastewater treatment plant effluent

Ozonation is an established solution for organic micropollutant (OMP) abatement in tertiary wastewater treatment. Biofiltration is the most common process for the biological post-treatment step, which is generally required to remove undesired oxidation products from the reaction of ozone with water matrix compounds. This study comparatively investigates the effect of filter media on the removal of organic contaminants and on biofilm properties for biologically activated carbon (BAC) and anthracite biofilters. Biofilms were analysed in two pilot-scale filters that have been operated for >50,000 bed volumes as post-treatment for ozonated wastewater treatment plant effluent. In parallel, the removal performance of bulk organics and OMP, including differentiation of adsorption and biotransformation through sodium azide inhibition, were carried out in bench-scale filter columns filled with material from the pilot filters. The use of BAC instead of anthracite resulted in an improved removal of organic bulk parameters, dissolved oxygen, and OMP. The OMP removal observed in the BAC filter but not in the anthracite filter was based on adsorption for most of the investigated compounds. For valsartan, however, biotransformation was found to be the dominant pathway, indicating that conditions for biotransformation of certain OMP are better on BAC than on anthracite. Adenosine triphosphate analyses in the media-attached biofilms of the pilot filters showed that biomass concentrations in the BAC filter were significantly higher than in the anthracite filter. The microbial communities (16S rRNA gene sequencing) appeared to be similar with respect to the types of organisms occurring on both filter materials. Alpha diversity also exhibited little variation between filter media. Beta diversity analysis, however, revealed that filter media and bed depth substantially influenced the biofilm composition. In practice, the impact of filter media on biofilm properties and biotransformation processes should be considered for the design of biofilters.

Ozonation of Selected Pharmaceutical and Personal Care Products in Secondary Effluent-Degradation Kinetics and Environmental Assessment

The efficiency of ozonation depends on the water matrix and the reaction time. Herein, these factors were addressed by assessing the removal of five pharmaceutical and personal care products (PPCPs) by ozonation. The main aims were: (i) to assess the effects of the water matrix on the degradation kinetics of PPCPs, individually and in mixture, following ozonation; and (ii) to assess the ecotoxicological impact of the ozone reaction time on the treatment of a spiked municipal wastewater (MW) added the five PPCPs over several species. The degradation of the PPCPs was faster in ultrapure water, with all PPCPs being removed in 20 min, whereas in the MW, a 30 min ozonation period was required to achieve a removal close to 100%. Increasing the number of PPCPs in the water matrix did not affect the time required for their removal in the MW. Regarding the ecotoxicity assessment, Raphidocelis subcapitata and Daphnia magna were the least sensitive species, whereas Lemna minor was the most sensitive. The temporal variation of the observed effects corroborates the degradation of the added PPCPs and the formation of toxic degradation by-products. The removal of the parent compounds did not guarantee decreased hazardous potential to biological species.

Acute ecotoxicological effects on daphnids and green algae caused by the ozonation of ibuprofen

Due to its ubiquitous presence in wastewaters, wastewater treatment plant effluents and even surface waters, the removal of the pharmaceutical ibuprofen from water is of special interest. Ozonation is widely applied for the treatment of micropollutants in wastewater treatment plants and is already known to also degrade ibuprofen. However, the formation of a wide range of transformation products during such oxidation steps might affect the aquatic environment. This study focuses on the acute ecotoxicological impact of the ibuprofen ozonation products on the two model organisms Daphnia magna and Desmodesmus subspicatus. For the identification of possibly ecotoxic products, a new workflow combining ecotoxicological testing, analytical methods and toxicity prediction was applied. Examination at different pH conditions with increasing ozone doses can point to respective products for further systematic examination. Seven ozonation products were confirmed in this study, two of them for the first time. Five previously postulated products were rejected. For pH 7 the inhibition of green algae growth was observed for mixtures oxidized with low ozone doses, while at pH 3 the mixtures with higher ozone doses caused toxic effects on the mobility of daphnids. Together with the analytical measurements in combination with ecotoxicity prediction, six products were identified which might have caused the toxic effect on green algae. However, no assignment to the observed toxic effects on daphnids was possible. The gained results indicate that mixture toxicity might play a role in oxidation processes and needs to be considered in ozonation studies concerning the ecotoxicological impact. Furthermore, the different observed toxicity for the two organisms underlines the importance of using multiple test systems for a comprehensive evaluation of the ecotoxicity during ozonation processes.

Treatability Studies on the Optimization of Ozone and Carbon Dosages for the Effective Removal of Contaminants from Secondary Treated Effluent

This study investigates the novel and advanced integrated pilot-scale treatment system of removal of contaminants in the secondary effluent from municipal wastewater. The main intent of this work is to assess the combination of pressure sand filter (PSF), ultrafiltration (UF), ozone (O3), and granular activated carbon (GAC) to treat wastewater and evaluate its suitability for water reuse. The experiments were carried out in a following condition: $\text{PSF}+\text{UF}+\text{O}3+\text{GAC}$ , $\text{PSF}+\text{O}3+\text{GAC}$ , and $\text{PSF}+\text{UF}+\text{GAC}$ . Configuration 1 was found to be more effective when compared to the other two and almost there occurred complete removal of contaminants. Whereas configuration 2 had the lowest removal efficiency of all, and configuration 3 had quite positive results. The influence of process parameters such as ozone dosage, flow rate, and filtration time was optimized. The optimized filtration time was 20 min with the filtration feed flow rate of 300 LPH. The best configuration of this treatment process produced a removal efficiency of about 80 to 90% with the ozone dosage of 8.33 mg/L with a flow rate of 4 l/min, whereas there occurred complete removal by the subsequent action of GAC. Moreover, the biodegradability of wastewaters as measured by the BOD5/COD ratio increased from 0.45 to 0.53. The proposed integrated pilot-scale process was effective in removing contaminants to the required level of discharge in the environment or reuse and it will pave the way to provide significant benefits to wastewater treatment.

Cross-linked laminar graphene oxide membranes for wastewater treatment and desalination: A review

Two-dimensional (2D) lamellar graphene oxide (GO) membranes are emerging as attractive materials for molecular separation in water treatment because of their single atomic thickness, excellent hydrophilicity, large specific surface areas, and controllable properties. To yet, commercialization of GO laminar membranes has been hindered by their propensity to swell in hydrated conditions. Thus, chemical crosslinking of GO sheets with the polymer matrix is used to improve GO membrane hydration stability. This review focuses on pertinent themes such as how chemical crosslinking improves the hydration stability, separation performance, and antifouling properties of GO membranes.

Assessing the protection gap for mobile and persistent chemicals during advanced water treatment - A study in a drinking water production and wastewater treatment plant

Persistent and mobile (PM) chemicals spread quickly in the water cycle and can reach drinking water. If these chemicals are also toxic (PMT) they may pose a threat to the aquatic environment and drinking water alike, and thus measures to prevent their spread are necessary. In this study, nontarget screening and cell-based toxicity tests after a polarity-based fractionation into polar and non-polar chemicals are utilized to assess and compare the effectiveness of ozonation and filtration through activated carbon in a wastewater treatment and drinking water production plant. Especially during wastewater treatment, differences in removal efficiency were evident. While median areas of non-polar features were reduced by a factor of 270, median areas for polar chemicals were only reduced by a factor of 4. Polar features showed significantly higher areas than their non-polar counterparts in wastewater treatment plant effluent and finished drinking water, implying a protection gap for these chemicals. Toxicity tests revealed higher initial toxicities (especially oxidative stress and estrogenic activity) for the non-polar fraction, but also showed a more pronounced decrease during treatment. Generally, the toxicity of the effluent was low for both fractions. Combined, these results imply a less effective removal but also a lower toxicity of polar chemicals. The behaviour of features during advanced waste and drinking water treatment was used to classify them as either PM chemicals or mobile transformation products (M-TPs). A suspect screening of the 476 highest intensity PM chemicals and M-TPs in 57 environmental and tap water samples showed high frequencies of detection (median >80%), which indicates the wide distribution of these chemicals in the aquatic environment and thus supports the chosen classification approach and the more generally applicability of obtained insights.

Influence of water matrix on the degradation of organic micropollutants by ozone based processes: A review on oxidant scavenging mechanism

The prevalence of organic micropollutants (OMPs) in aquatic environment has expedited scientific and regulatory efforts to retrofit existing wastewater treatment plants (WWTPs). The current strategy involves WWTPs upgrading with post-ozonation i.e., ozone (O₃) and/or peroxone process (O₃ +H₂O₂). Still, ozone-based degradation of OMPs faces several challenges. For example, the degradation mechanism and kinetics of OMPs could largely be affected by water matrix compounds which include inorganic ions and natural organic matter (NOM). pH also plays a decisive role in determining the reactivity of the oxidants (O₃, H₂O₂, andHO^•), stability and speciation of matrix constituents and OMPs and thus susceptibility of OMPs to the reactions with oxidants. There have been reviews discussing the impact of matrix components on the degradation of OMPs by advanced oxidation processes (AOPs). Nevertheless, a review focusing on scavenging mechanisms, formation of secondary oxidants and their scavenging effects with a particular focus on ozonation and peroxone process is lacking. Therefore, in order to broaden the knowledge on this subject, the database 'Web of Science' was searched for the studies related to the 'matrix effect on the degradation of organic micropollutants by ozone based processes' over the time period of 2004-2021. The relevant literature was thoroughly reviewed and following conclusions were made: i) chloride has inhibitory effects if it exits at higher concentrations or as free chlorine i.e. HOCl/ClO^-. ii) The inhibitory effects of chloride, bromide, HOBr/OBr^- and HOCl/ClO^- are dominant in neutral and alkaline conditions and may result in the formation of secondary oxidants (e.g., chlorine atoms or free bromine), which in turn contribute to pollutant degradation or form undesired oxidation by-products such as BrO₃^-, ClO₃^- and halogenated organic products. ii) NOM may induce inhibitory or synergetic effects depending on the type, chemical properties and concentration of NOM. Therefore, more efforts are required to understand the importance of pH variation as well as the effects of water matrix on the reactivity of oxidants and subsequent degradation of OMPs.

Ozonation of organic compounds in water and wastewater: A critical review

Ozonation has been applied in water treatment for more than a century, first for disinfection, later for oxidation of inorganic and organic pollutants. In recent years, ozone has been increasingly applied for enhanced municipal wastewater treatment for ecosystem protection and for potable water reuse. These applications triggered significant research efforts on the abatement efficiency of organic contaminants and the ensuing formation of transformation products. This endeavor was accompanied by developments in analytical and computational chemistry, which allowed to improve the mechanistic understanding of ozone reactions. This critical review assesses the challenges of ozonation of impaired water qualities such as wastewaters and provides an up-to-date compilation of the recent kinetic and mechanistic findings of ozone reactions with dissolved organic matter, various functional groups (olefins, aromatic compounds, heterocyclic compounds, aliphatic nitrogen-containing compounds, sulfur-containing compounds, hydrocarbons, carbanions, β-diketones) and antibiotic resistance genes.

Biological effect and chemical monitoring of Watch List substances in European surface waters: Steroidal estrogens and diclofenac - Effect-based methods for monitoring frameworks

Three steroidal estrogens, 17α-ethinylestradiol (EE2), 17β-estradiol (E2), estrone (E1), and the non-steroidal anti-inflammatory drug (NSAID), diclofenac have been included in the first Watch List of the Water Framework Directive (WFD, EU Directive 2000/60/EC, EU Implementing Decision 2015/495). This triggered the need for more EU-wide surface water monitoring data on these micropollutants, before they can be considered for inclusion in the list of priority substances regularly monitored in aquatic ecosystems. The revision of the priority substance list of the WFD offers the opportunity to incorporate more holistic bioanalytical approaches, such as effect-based monitoring, alongside single substance chemical monitoring. Effect-based methods (EBMs) are able to measure total biological activities (e.g., estrogenic activity or cyxlooxygenase [COX]-inhibition) of specific group of substances (such as estrogens and NSAIDs) in the aquatic environment at low concentrations (pg/L). This makes them potential tools for a cost-effective and ecotoxicologically comprehensive water quality assessment. In parallel, the use of such methods could build a bridge from chemical status assessments towards ecological status assessments by adressing mixture effects for relevant modes of action. Our study aimed to assess the suitability of implementing EBMs in the WFD, by conducting a large-scale sampling and analysis campaign of more than 70 surface waters across Europe. This resulted in the generation of high-quality chemical and effect-based monitoring data for the selected Watch List substances. Overall, water samples contained low estrogenicity (0.01-1.3 ng E2-Equivalent/L) and a range of COX-inhibition activity similar to previously reported levels (12-1600 ng Diclofenac-Equivalent/L). Comparison between effect-based and conventional analytical chemical methods showed that the chemical analytical approach for steroidal estrogens resulted in more (76%) non-quantifiable data, i.e., concentrations were below detection limits, compared to the EBMs (28%). These results demonstrate the excellent and sensitive screening capability of EBMs.

Integrating dissolved and particulate matter into a prediction tool for ozonation of organic micropollutants in wastewater

Ozonation is an established technique used to reduce the discharge of organic micropollutants into the aquatic environment, but the possibility of predicting the ozone demand for different wastewater matrices is still limited, especially in the presence of suspended solids (SS). A new tool for the prediction of the removal of organic micropollutants with ozone, based on dissolved and particulate matter in activated sludge effluents, was therefore developed. The removal of 25 organic micropollutants was determined on laboratory scale in the presence and absence of suspended solids. The linear trajectories of the dose-response curves enabled the determination of a new set of removal constants, based on dissolved chemical oxygen demand (COD) and SS. The presence of SS had a more negative effect on the removal of slow-reacting micropollutants (removal constant <3.5 mg COD_Cr,diss·mg O₃^-1) with ozone than on the fast-reacting micropollutants (removal constant >3.5 mg COD_Cr,diss·mg O₃^-1). However, the decreased removal of the organic micropollutants was generally small, <10%, at typical SS concentrations, <25 mg SS·L^-1. Integration of the new removal constants based on COD and SS enabled the removal in an ozone pilot plant to be modelled with an average deviation of <10% for several organic micropollutants. The use of the frequently measured parameters, COD and SS, as input parameters could facilitate the future use of the tool to predict the removal of micropollutants during ozonation.

Monitoring of emerging contaminants of concern in the aquatic environment: a review of studies showing the application of effect-based measures

Water scarcity is increasingly a global cause of concern mainly due to widespread changes in climate conditions and increased consumptive water use driven by the exponential increase in population growth. In addition, increased pollution of fresh water sources due to rising production and consumption of pharmaceuticals and organic chemicals will further exacerbate this concern. Although surface water contamination by individual chemicals is often at very low concentration, pharmaceuticals for instance are designed to be efficacious at low concentrations, creating genuine concern for their presence in freshwater sources. Furthermore, the additive impact of multiple compounds may result in toxic or other biological effects that otherwise will not be induced by individual chemicals. Globally, different legislative frameworks have led to pre-emptive efforts which aim to ensure good water ecological status. Reports detailing the use and types of effect-based measures covering specific bioassay batteries that can identify specific mode of actions of chemical pollutants in the aquatic ecosystem to evaluate the real threat of pollutants to aquatic lives and ultimately human lives have recently emerged from monitoring networks such as the NORMAN network. In this review, we critically evaluate some studies within the last decade that have implemented effect-based monitoring of pharmaceuticals and organic chemicals in aquatic fauna, evaluating the occurrence of different chemical pollutants and the impact of these pollutants on aquatic fauna with special focus on pollutants that are contaminants of emerging concern (CEC) in urban wastewater. A critical discussion on studies that have used effect-based measures to assess biological impact of pharmaceutical/organic compound in the aquatic ecosystem and the endpoints measurements employed is presented. The application of effect-based monitoring of chemicals other than assessment of water quality status is also discussed.

The promotions on radical formation and micropollutant degradation by the synergies between ozone and chemical reagents (synergistic ozonation): A review

The combination of ozone (O₃) and chemical reagents (such as H₂O₂) shows synergies on the radical formation and micropollutant degradation. The promoting performance was associated with various parameters including chemical reagents, micropollutants, solution pH, and the water matrix. In this review, we summarized existing knowledge on radical formation pathways, radical yields, and radical oxidation for different synergistic ozonation processes in various water matrices (such as groundwater, surface water, and wastewater). The increase of radical yields by synergistic ozonation processes was positively related to the increase of O₃-decay, with the increase being 1.1-4.4 folds than ozonation alone (0.2). Thus, synergistic ozonation can promote the degradation rate and efficiency of O₃-resistant micropollutants (second order rate constant, k_P,O3 < 200 M^-1 s^-1), but only slightly affects or even minorly inhibits the degradation of O₃-reactive micropollutants (k_P,O3 > 200 M^-1 s^-1). The water matrices^, such as the dissolved organic matters, negatively suppressed the degradation of micropollutant by quenching O₃-oxidation and radical oxidation (i.e. maximum promoting was decreased by 1.3 times), but may positively extend the promoting effects of synergistic ozonation to micropollutants that are more reactive to O₃ (i.e. k_P,O3 was extended from <200 to <2000 M^-1 s^-1). The formation of bromate would be increased through increasing radical oxidation by synergistic ozonation, but can be depressed by relative higher H₂O₂ as the reducing agent of HOBr/OBr^- intermediate. The increase in bromate formation by O₃/permononsulfate is a considerable concern due to permononsulfate cannot reduce the HOBr/OBr^- intermediate.

Screening priority indicator pollutants in full-scale wastewater treatment plants by non-target analysis

Wastewater treatment plants (WWTPs) are the main sources of emerging contaminants (ECs) in aquatic environment. However, the standards for limiting emerging pollutants in effluent are extremely lacking. We investigated the occurrence and removal of emerging pollutants in 16 WWTPs in China using non-target analysis. 568 substances screened out were divided into 9 kinds including 167 pharmaceuticals, 113 natural substances, 85 pesticides, 86 endogenous substances, 64 chemical raw materials, 14 personal care products, 17 food additives, 6 hormones and 16 others. And they were divided into 5 fates. Pesticides and pharmaceutical compounds seemed to be the most notable categories, the kinds detected in each sample is the largest compared with other compounds. Besides, the average removal rate of pesticides and pharmaceuticals in all WWTPs were the lowest, at 9.54% and 23.77%, respectively. Priority pollutants were screened by considering distribution of pollutants with different fates. Pollutants with the same fate especially "consistent" in different WWTPs had attracted attention. 4 potential priority pollutants including metoprolol, carbamazepine, 10, 11-dihydro-10, 11-dihydroxycarbamazepine and irbesartan were proposed. And it was found that the 4 compounds, "consistent suspects" and "consistent non-targets" had similar rankings of removal rate in 16 WWTPs, which can reflect the performance of different WWTPs.

Characterization of advanced wastewater treatment with ozone and activated carbon using LC-HRMS based non-target screening with automated trend assignment

Advanced treatment is increasingly being applied to improve abatement of micropollutants in wastewater effluent and reduce their load to surface waters. In this study, non-target screening of high-resolution mass spectrometry (HRMS) data, collected at three Swiss wastewater treatment plants (WWTPs), was used to evaluate different advanced wastewater treatment setups, including (1) granular activated carbon (GAC) filtration alone, (2) pre-ozonation followed by GAC filtration, and (3) pre-ozonation followed by powdered activated carbon (PAC) dosed onto a sand filter. Samples were collected at each treatment step of the WWTP and analyzed with reverse-phase liquid chromatography coupled to HRMS. Each WWTP received a portion of industrial wastewater and a prioritization method was applied to select non-target features potentially resulting from industrial activities. Approximately 37,000 non-target features were found in the influents of the WWTPs. A number of non-target features (1207) were prioritized as likely of industrial origin and 54 were identified through database spectral matching. The fates of all detected non-target features were assessed through a novel automated trend assignment method. A trend was assigned to each non-target feature based on the normalized intensity profile for each sampling date. Results showed that 73±4% of influent non-target features and the majority of industrial features (89%) were well-removed (i.e., >80% intensity reduction) during biological treatment in all three WWTPs. Advanced treatment removed, on average, an additional 11% of influent non-target features, with no significant differences observed among the different advanced treatment settings. In contrast, when considering a subset of 66 known micropollutants, advanced treatment was necessary to adequately abate these compounds and higher abatement was observed in fresh GAC (7,000-8,000 bed volumes (BVs)) compared to older GAC (18,000-48,000 BVs) (80% vs 56% of micropollutants were well-removed, respectively). Approximately half of the features detected in the WWTP effluents were features newly formed during the various treatment steps. In ozonation, between 1108-3579 features were classified as potential non-target ozonation transformation products (OTPs). No difference could be observed for their removal in GAC filters at the BVs investigated (70% of OTPs were well-removed on average). Similar amounts (67%) was observed with PAC (7.7-13.6 mg/L) dosed onto a sand filter, demonstrating that a post-treatment with activated carbon is efficient for the removal of OTPs.

Influence of operational conditions and wastewater properties on the removal of organic micropollutants through ozonation

The objective of this study was to evaluate the influence of operational conditions and wastewater properties on the removal of pharmaceuticals, contrast media and antibiotics through ozonation, in order to facilitate the optimization of treatment and its implementation on a full scale. Pilot-scale ozone oxidation trials were performed on treated wastewater, before and after post-precipitation, over a seven-month period, including summer and winter months. Hydraulic retention times as short as 7 min were found to be sufficient for organic micropollutant removal. A short hydraulic retention time reduces both investment costs and land use. Neither the choice of ozone dispersion method, a static mixer or a Venturi injector, nor the wastewater temperature had any significant effect on the removal efficiency of organic micropollutants, however, higher removal was achieved after on-site post-precipitation with aluminum chloride.

Emerging organic contaminants and odorous compounds in secondary effluent wastewater: Identification and advanced treatment

This study aims to address organic micropollutants in secondary effluents from municipal wastewater treatment plants (WWTPs) by first identification of micropollutants in different treatment units, and second by evaluating an advanced treatment process for removals of micropollutants. In secondary effluents, 28 types of pharmaceutical and personal care products (PPCPs), 5 types of endocrine disrupting chemicals (EDCs) and 3 types of odorous compounds are detected with total concentrations of 513 ± 57.8 ng/L, 991 ± 36.5 ng/L, 553 ± 48.3 ng/L, respectively. An integrated process consisting of in-situ ozonation, ceramic membrane filtration (CMF) and biological active carbon (BAC) filtration is investigated in a pilot scale (1000 m³/d) for removal of micropollutants in secondary effluents. The total removal efficiencies of PPCPs, EDCs and odorous compounds are 98.5%, 95.4%, and 91.1%, respectively. Removal mechanisms of emerging organic contaminants (EOCs) and odorous compounds are discussed based on their physicochemical properties. The remarkable removal efficiencies of micropollutants by the pilot system is attributed to synergistic effects of combining ozonation, ceramic membrane filtration and BAC filtration. This study provides a cost-effective and robust technology with the capability of treating secondary effluents for reuse applications.

Removal of pharmaceutical metabolites in wastewater ozonation including their fate in different post-treatments

Advanced treatment technologies for the removal of pharmaceuticals and other organic micropollutants in WWTPs primarily target the removal of parent compounds. Nevertheless, the removal of metabolites originating from human- or microbial metabolism during biological treatment needs comparable consideration, as some of them might be present in high concentrations and contribute to toxicity. This study was conducted to elucidate the removal of human and microbial metabolites of pharmaceuticals as a function of the specific ozone dose. Ozonation was performed on four sites with two pilot- and two full-scale plants operated downstream of conventional activated sludge plants. The ozone reactivity of all metabolites (expressed as the ozone dose to remove 90% of the compound/decadic ozone dose) was lower than those of their parent compounds. The decadic ozone dose was 1.0, 1.3 and 1.1 mg O₃/mg DOC for Epoxy-carbamazepine, Di-OH-carbamazepine and N-Desmethyl tramadol, respectively. 20-40% of the remaining metabolites were removed in a polishing sand/BAC-filter (biological activated carbon). Similar removal was observed for Epoxy-carbamazepine, Di-OH-carbamazepine and Hydroxy-diclofenac in a constructed wetland. However, the sand/anthracite filter had no effect. All four metabolites were removed in a GAC (granulated activated carbon) filter.

MBBRs as post-treatment to ozonation: Degradation of transformation products and ozone-resistant micropollutants

The degradation potential of micropollutants and transformation products in biological post-treatment after ozonation is partly unknown. A pilot plant with ozonation and subsequent biological treatment in a moving bed biofilm reactor (MBBR) was thus operated over 16 months to investigate the removal of micropollutants and the formation and removal of N-oxide transformation products. Lab-scale kinetic experiments were performed in parallel. At a moderate ozone dose of 0.5 g O₃ g^-1 DOC, further degradation of gabapentin and 3 iodinated contrast media (iomeprol, iopamidol, and iohexol) could be induced by the biofilm at prolonged exposure times. To facilitate comparison of feeding regimens in biofilm systems a new surface-related degradation rate constant was introduced. The availability of substrates in the pilot MBBR influenced the micropollutant degradation kinetics with increasing and decreasing degradation rates. N-oxides from erythromycin, clarithromycin, tramadol, and venlafaxine were formed during ozonation and could not be degraded by the biofilm.

High-performance thin-layer chromatography in combination with a yeast-based multi-effect bioassay to determine endocrine effects in environmental samples

Effect-directed analysis (EDA) that combines effect-based methods (EBMs) with high-performance thin-layer chromatography (HPTLC) is a useful technique for spatial, temporal, and process-related effect evaluation and may provide a link between effect testing and responsible substance identification. In this study, a yeast multi endocrine-effect screen (YMEES) for the detection of endocrine effects is combined with HPTLC. Simultaneous detection of estrogenic, androgenic, and gestagenic effects on the HPTLC plate is achieved by mixing different genetically modified Arxula adeninivorans yeast strains, which contain either the human estrogen, androgen, or progesterone receptor. Depending on the yeast strain, different fluorescent proteins are formed when an appropriate substance binds to the specific hormone receptor. This allows to measure hormonal effects at different wavelengths. Two yeast cell application approaches, immersion and spraying, are compared. The sensitivity and reproducibility of the method are shown by dose-response investigations for reference compounds. The spraying approach indicated similar sensitivities and higher precisions for the tested hormones compared to immersion. The EC₁₀s for estrone (E1), 17β-estradiol (E2), 17α-ethinylestradiol (EE2), 5α-dihydrotestosterone (DHT), and progesterone (P4) were 95, 1.4, 10, 7.4, and 15 pg/spot, respectively. Recovery rates of E1, E2, EE2, DHT, and P4 between 88 and 120% show the usability of the general method in combination with sample enrichment by solid phase extraction (SPE). The simultaneous detection of estrogenic, androgenic, and gestagenic effects in wastewater and surface water samples demonstrates the successful application of the YMEES in such matrices. This promising method allows us to identify more than one endocrine effect on the same HPTLC plate, which saves time and material. The method could be used for comparison, evaluation, and monitoring of different river sites and wastewater treatment steps and should be tested in further studies.

High resolution effect-directed analysis of steroid hormone (ant)agonists in surface and wastewater quality monitoring

Monitoring of chemical water quality is extremely challenging due to the large variety of compounds and the presence of biologically active compounds with unknown chemical identity. Previously, we developed a high resolution Effect-Directed Analysis (EDA) platform that combines liquid chromatography with high resolution mass spectrometry and parallel bioassay detection. In this study, the platform is combined with CALUX bioassays for (anti)androgenic, estrogenic and glucocorticoid activities, and the performance of the platform is evaluated. It appeared to render very repeatable results, with high recoveries of spiked compounds and high consistency between the mass spectrometric and bioassay results. Application of the platform to wastewater treatment plant effluent and surface water samples led to the identification of several compounds contributing to the measured activities. Eventually, a workflow is proposed for the application of the platform in a routine monitoring context. The workflow divides the platform into four phases, of which one to all can be performed depending on the research question and the results obtained. This allows one to make a balance between the effort put into the platform and the certainty and depth by which active compounds will be identified. The EDA platform is a valuable tool to identify unknown bioactive compounds, both in an academic setting as in the context of legislative, governmental or routine monitoring.

Post-treatment of ozonated wastewater with activated carbon and biofiltration compared to membrane bioreactors: Toxicity removal in vitro and in Potamopyrgus antipodarum

Wastewater treatment plants are major point sources of (micro)pollutant emissions and advanced wastewater treatment technologies can improve their removal capacity. While abundant data on individual advanced treatment technologies is available, there is limited knowledge regarding the removal performance of ozonation combined with multiple post-treatments and stand-alone membrane bioreactors. This is especially true for the removal of in vitro and in vivo toxicity. Therefore, we investigated the removal of 40 micropollutants and toxicity by a pilot-scale ozonation with four post-treatments: non-aerated and aerated granular activated carbon and biological filtration. In addition, two stand-alone membrane bioreactors fed with untreated wastewater and one MBR operating with ozonated partial flow recirculation were analysed. Aqueous and extracted samples were analysed in vitro for (anti)estrogenic, (anti)androgenic and mutagenic effects. To assess in vivo effects, the mudsnail Potamopyrgus antipodarum was exposed in an on-site flow-through system. Multiple in vitro effects were detected in conventionally treated wastewater including estrogenic and anti-androgenic activity. Ozonation largely removed these effects, while anti-estrogenic and mutagenic effects increased suggesting the formation of toxic transformation products. These effects were significantly reduced by granular activated carbon being more effective than biological filtration. The membrane bioreactor performed similarly to the conventional treatment while the membrane bioreactor with ozonation had a comparable removal performance like ozonation. Conventionally treated wastewater increased the growth of P. antipodarum. Ozonation reduced the reproduction indicating a potential formation of toxic transformation products. In the post-treatments, these effects were compensated or remained unaffected. The effluents of the membrane bioreactors induced reproductive toxicity. Our results show that ozonation is effective in further reducing toxicity and micropollutant concentrations. However, the formation of toxicity requires a post-treatment. Here, ozonation coupled to granular activated carbon filtration seemed the most promising treatment process.