Field Evaluation and in Situ Stress Testing of the Organic-Diffusive Gradients in Thin-Films Passive Sampler

Utility of a modified o-DGT passive sampler for measurement of bisphenol analogues in freshwater and coastal waters

Bisphenol analogues (BPs) are commonly found in riverine and coastal waters. However, the lack of a reliable and robust passive sampling method has hindered our ability to monitor these compounds in aquatic systems. The study developed a novel organic-diffusive gradients in thin film (o-DGT) sampler based on stainless steel mesh membrane, polyacrylamide diffusive gel, and hydrophilic-lipophilic balance (HLB) binding gel. This innovative design tackled issues of filter membrane sorption in traditional o-DGT devices and potential gel damage in membrane-less o-DGT devices, showing promising application prospects. The mass accumulation of 15 target BPs was linear over 10 days in both freshwater (r2 ≥ 0.92) and seawater (r2 ≥ 0.94), with no saturation observed. The diffusion coefficients (D) through polyacrylamide diffusive gels ranged from 4.04 × 10-6 to 5.77 × 10-6 cm2 s-1 in freshwater and from 1.74 × 10-6 to 4.69 × 10-6 cm2 s-1 in seawater for the target BPs (except for bisphenol PH) at 22 °C. The D values of the target BPs in seawater were lower than those in freshwater due to the high salinity in seawater (35 ‰). The o-DGT samplers demonstrated good integrity in field applications. The total concentrations of the eight detected BPs ranged from 9.2 to 323 ng L-1, which was consistent with the measurements obtained by grab sampling. Among all BPs, bisphenol S, bisphenol F, and bisphenol A were consistently detected at all sites using both sampling methods. The concentrations of some novel BPs in coastal water measured by grab sampling were comparable to those measured in rivers, suggesting the need to strengthen pollution control of BPs in coastal areas. These results indicate that the o-DGT passive sampling method developed in the present study can be effectively used for monitoring BPs in freshwater and coastal environments.

Evaluation of the DGT passive samplers for integrating fluctuating concentrations of pharmaceuticals in surface water

Diffusive gradients in thin films (DGTs) have been well-documented for the measurement of a broad range of organic pollutants in surface water. However, the performance has been challenged by the inherent periodic concentration fluctuations for most organic pollutants. Therefore, there is an urgent need to assess the true time-weighted average (TWA) concentration based on fluctuating concentration profiles. The study aimed to evaluate the responsiveness of DGT and accuracy of TWA concentrations, considering various concentration fluctuating scenarios of 20 pharmaceuticals in surface water. The reliability and accuracy of the TWA concentrations measured by the DGT were assessed by comparison with the sum of cumulative mass of DGT exposed at different stages over the deployment period. The results showed that peak concentration duration (1-5 days), peak concentration fluctuation intensity (6-20 times), and occurrence time of peak concentration fluctuation (early, middle, and late stages) have minimal effect on DGT's response to most target pharmaceutical concentration fluctuations (0.8 < CDGT/CTWA < 1.2). While the downward-bent accumulations of a few pharmaceuticals on DGT occur as the sampling time increases, which could be accounted for by capacity effects during a long-time sampling period. Additionally, the DGT device had good sampling performance in recording short fluctuating concentrations from a pulse event returning to background concentrations with variable intensity and duration. This study revealed a satisfactory capacity for the evaluation of the TWA concentration of pharmaceuticals integrated over the period of different pulse deployment for DGT, suggesting that this passive sampler is ideally suited as a monitoring tool for field application. This study represents the first trial for evaluating DGT sampling performance for pharmaceuticals with multiple concentration fluctuating scenarios over time, which would be valuable for assessing the pollution status in future monitoring campaign.

Measurement of perfluoroalkyl substances in drinking water sources by DGT sampler with a novel fluorinated graphite binding gel

Extensive use of per- and polyfluoroalkyl substances (PFASs) has resulted in their widespread presence in natural waters. Concern for public health requires reliable measurement methods for determining their distribution and risks. Here, a sampling method based on diffusive gradients in thin films (DGT) was developed for measuring PFASs in drinking water sources. Fluorinated graphite (FG) particles were used to prepare the DGT binding gel for selective enrichment of trace PFASs in an aqueous environment. The FG-DGT method did not show sensitivity to relevant environmental parameters including pH (5.0-9.0), ionic strength (0.001-0.5 M), or DOM concentration (0-30 mg/L). The FG-DGT had enough capacity for deployment of up to four months. Six traditional and emerging PFASs including PFOS, PFOA, PFHpA, PFHxS, PFNA, and 6:2 FTSA at the ng/L level were detected in two major reservoirs serving as public drinking water sources by FG-DGT method coupled with liquid chromatography tandem mass spectrometry (LC-MS/MS). PFOA appeared at the highest observed concentrations in the drinking water sources. The research demonstrates that FG-DGT is an effective and efficient tool for monitoring PFASs in drinking water.

Performance comparison of three passive samplers for monitoring of polar organic contaminants in treated municipal wastewater

Over the past decades, several types of passive samplers have been developed and used to monitor polar organic compounds in aquatic environments. These samplers use different sorbents and barriers to control the uptake into the sampler, but their performance comparison is usually not well investigated. This study aimed to directly compare the performance of three samplers, i.e., the Polar Organic Chemical Integrative Sampler (POCIS), the Hydrogel-based Passive Sampler (HPS, an upscaled version of o-DGT), and the Speedisk, on a diverse suite of pharmaceuticals, per- and polyfluoroalkylated substances (PFAS), and pesticides and their metabolites. The samplers were deployed side-by-side in the treated effluent of a municipal wastewater treatment plant for different exposure times. All samplers accumulated a comparable number of compounds, and integrative uptake was observed for most compounds detected up to 28 days for POCIS, up to 14 days for HPS, and up to 42 days for Speedisk. In the integrative uptake phase, consistent surface-specific uptake was observed with a significant correlation between samplers (r ≥ 0.76) despite differences in sampler construction, diffusion barrier, and sorbent material used. The low sampling rates compared to the literature and the low estimated overall mass transfer coefficient suggests that the water boundary layer was the main barrier controlling the uptake for all samplers. Although all devices provided comparable performance, Speedisk overcomes POCIS and HPS in several criteria, including time-integrative sampling over a long period and physical durability.

Application of passive sampling device for exploring the occurrence, distribution, and risk of pharmaceuticals and pesticides in surface water

Pharmaceuticals and pesticides are compounds of high concern in surface waters around the world. However, few studies have used passive sampling methods to screen and detect these compounds in natural waters. In this study, a self-developed passive sampler was employed to measure pharmaceuticals and pesticides in the rivers of Nanjing, China. A total of 41 pharmaceuticals and 11 pesticides were detected, among which antibiotic and insecticide were the predominant classes, respectively. Valproic acid, caffeine and triclosan from the pharmaceuticals, and isoprocarb and imidacloprid from the pesticides were found frequently with high concentrations. At most sampling sites, the concentration ratios of caffeine versus carbamazepine exceeded 10, and even above 50, indicating relatively poor efficiency of wastewater treatment, or possibly the direct discharge of raw sewage, or other unknown source of pollution. It was found that the concentrations and ecological risks in the northern area of Yangtze River were higher than those in the southern area of Yangtze River, implying that economic development and population density were not the main contributors to the discovered pollution. The total concentration of pharmaceuticals and pesticides in Qinhuai River increased gradually with the direction of water flow, demonstrating the success of water diversion project in flushing and scouring pollutants.

Organic diffusive gradients in thin films (o-DGT) for determining environmental behaviors of antibiotics: A review

Antibiotics are recognized as effective medicine that has been extensively used in human and veterinary. Since the rate of releasing into the environment is stronger than the rate of elimination, antibiotics are regarded as persistent or "pseudo-persistent" organic compounds that result in the development of microbial antibiotic resistance. Therefore, assessment for their ecological risks to the environment are essential. Diffusive gradients in thin films for organic compounds (o-DGT) have been adapted to investigate the environmental behaviors of antibiotics. Currently, more than 20 compounds have been tested by o-DGT in waters and soil environments. In this review, we explained the theoretical reason that o-DGT is feasible to determine the labile fraction of antibiotics in different environmental media. The most used agarose diffusive gel, and various binding agents such as resin, porous carbon and nano-scale materials have been compared to optimize the sampling of antibiotics by o-DGT. Results of deploying o-DGT devices in waters and soils from previous studies were discussed to understand the bioavailability and dynamic transport of antibiotics. Also, we provided the feasibility analysis of using o-DGT in sediments for antibiotics measurements, which is required to be carried out in future studies. To have a deep view on the development of o-DGT, its technical limitations and viable improvements were summarized in this study for further applications on antibiotics research.

Development and application of diffusive gradients in thin films for in situ sampling of the organic UV filter 4-methylbenzylidene camphor (4-MBC) in waters

4-Methylbenzylidene camphor (4-MBC), a typical organic UV filter (OUVF) in personal care products, is considered to be a potential endocrine disruptor due to its estrogenic activity and bioaccumulation. Although 4-MBC residues have been extensively identified in aquatic waters, little is known about their occurrence, levels, and potential risk in coastal waters. This study developed a reliable sampling approach, based on diffusive gradients in thin films (DGT) with XAD-2 as the binding agent, for monitoring 4-MBC in coastal waters. The diffusion coefficients of 4-MBC in freshwater and artificial seawater were 3.65 × 10-6 cm2/s and 3.83 × 10-6 cm2/s, respectively. XAD-2 binding gel showed rapid adsorption to 4-MBC. The accumulated masses of 4-MBC in XAD-2 DGT increased linearly with deployed time for 7 days in freshwater and seawater, which agreed well with theoretical predictions. The sampling performance was independent of ionic strength (0.0001-0.5 M), pH (4.0-8.5), and dissolved organic matter (0-20 mg/L). Field deployment in the river estuary and bathing beach showed that DGT-measured 4-MBC concentrations were consistent in comparison with grab sampling. Environmental risk assessment showed that 4-MBC may pose a medium risk to aquatic organisms based on computed risk quotient (RQ) values. Sewage discharge is the main source of 4-MBC risk, while the residue in recreation beaches contributes more significantly in summer. The established DGT sampling is suitable for seasonal monitoring, source identification, and risk assessment of 4-MBC in coastal waters.

Interest of a new large diffusive gradients in thin films (L-DGT) for organic compounds monitoring: On-field comparison with conventional passive samplers

In this work, the performances of a Large Diffusive Gradients in Thin films (L-DGT, i.e., a DGT based on a Chemcatcher® holder with a 5-fold larger sampling area) were compared on-field with the conventional DGT and the Polar Organic Chemical Integrative Sampler (POCIS) for the monitoring of a wide range of organic contaminants (i.e., 65 pesticides and metabolites, 53 pharmaceuticals and 12 hormones). These three passive samplers were simultaneously deployed in four rivers during 14 days. Their performances were then evaluated according to their detection and quantification capacities and their physical robustness. The results obtained confirm the advantages of the L-DGT over the conventional DGT regarding its sensitivity but also its robustness during field deployment. The POCIS provides the higher sensitivity, allowing the detection of more organic compounds compared to the DGT and, to a lesser extent, the L-DGT. However, both L-DGT and DGT reduces the uncertainty on the determination of the time-weighted average concentrations (C_W), mainly due to the narrow range of variation of their calibration parameters. Indeed, for a given compound, C_W can vary up to only a 3-fold factor with DGT and L-DGT compared to a 2 to 10-fold factor (up to 50) with POCIS. Thus, the L-DGT appears to be more suitable than DGT in low-contaminated contexts, which require higher sensitivity, or than POCIS when a C_W determination is needed. For a qualitative evaluation however, the POCIS remains the most suitable passive sampler.

Passive Sampling: A Greener Technique for the 'Dual Carbon' Goal While Implementing the Action Plan for Controlling Emerging Pollutants

In response to global climate change, China recently committed to achieving peak carbon emissions by 2030 and carbon neutrality by 2060. Carbon emission reduction should be considered in every sector of society including environmental monitoring. As an energy-saving technique in environmental monitoring, passive sampling has many advantages, such as in-situ sampling and a reduction in time/labour requirements. This perspective illustrates the "greenness" of passive sampling techniques, by comparison with traditional sampling methods, and its potential contribution to the 'dual carbon' goal. At the same time passive sampling can provide key support for the action plan for controlling emerging pollutants in China.

A Review of In Situ Methods-Solid Phase Adsorption Toxin Tracking (SPATT) and Polar Organic Chemical Integrative Sampler (POCIS) for the Collection and Concentration of Marine Biotoxins and Pharmaceuticals in Environmental Waters

Solid Phase Adsorption Toxin Tracking (SPATT) and Polar Organic Chemical Integrative Sampler (POCIS) are in situ methods that have been applied to pre-concentrate a range of marine toxins, pesticides and pharmaceutical compounds that occur at low levels in marine and environmental waters. Recent research has identified the widespread distribution of biotoxins and pharmaceuticals in environmental waters (marine, brackish and freshwater) highlighting the need for the development of effective techniques to generate accurate quantitative water system profiles. In this manuscript, we reviewed in situ methods known as Solid Phase Adsorption Toxin Tracking (SPATT) and Polar Organic Chemical Integrative Sampler (POCIS) for the collection and concentration of marine biotoxins, freshwater cyanotoxins and pharmaceuticals in environmental waters since the 1980s to present. Twelve different adsorption substrates in SPATT and 18 different sorbents in POCIS were reviewed for their ability to absorb a range of lipophilic and hydrophilic marine biotoxins, pharmaceuticals, pesticides, antibiotics and microcystins in marine water, freshwater and wastewater. This review suggests the gaps in reported studies, outlines future research possibilities and guides researchers who wish to work on water contaminates using Solid Phase Adsorption Toxin Tracking (SPATT) and Polar Organic Chemical Integrative Sampler (POCIS) technologies.

Diffusive gradients in thin films (DGT) probe for effectively sampling of per- and polyfluoroalkyl substances in waters and sediments

The passive sampling technique, diffusive gradients in thin films (DGT) has attracted increasing interests as an in-situ sampler for organic contaminants including per- and polyfluoroalkyl substances (PFAS). However, its effectiveness has been questioned because of the small effective sampling area (3.1 cm²). In this study, we developed a DGT probe for rapid sampling of eight PFAS in waters and applied it to a water-sediment system. It has a much larger sampling area (27 cm²) and as a result lower method quantification limits (0.15 - 0.21 ng/L for one-day deployment and 0.02 - 0.03 ng/L for one-week deployment) and much higher (by > 10 factors) sampling rate (100 mL/day) compared to the standard DGT (piston configuration). The sampler could linearly accumulate PFAS from wastewater, was sensitive enough even for a 24 hr deployment with performance comparable to grab sampling (500 mL). The DGT probe provided homogeneous sampling performance along the large exposure area. The use of the probe to investigate distributions of dissolved PFAS around the sediment-water interface was demonstrated. This work, for the first time, demonstrated that the DGT probe is a promising monitoring tool for trace levels of PFAS and a research tool for studying their distribution, migration, and fate in aquatic environments including the sediment-water interface.

A Review on Polyethersulfone Membranes in Polar Organic Chemical Integrative Samplers: Preparation, Characterization and Innovation

The membranes in polar organic chemical integrative samplers (POCIS) enclose the receiving sorbent and protect it from coming into direct contact with the environmental matrix. They have a crucial role in extending the kinetic regime of contaminant uptake, by slowing down their diffusion between the water phase and the receiving phase. The drive to improve passive sampling requires membranes with better design and enhanced performances. In this review, the preparation of standard polyethersulfone (PES) membranes for POCIS is presented, as well as methods to evaluate their composition, morphology, structure, and performance. Generally, only supplier-related morphological and structural data are provided, such as membrane type, thickness, surface area, and pore diameter. The issues related to the use of PES membranes in POCIS applications are exposed. Finally, alternative membranes to PES in POCIS are also discussed, although no better membrane has yet been developed. This review highlights the urge for more membrane characterization details and a better comprehension of the mechanisms which underlay their behavior and performance, to improve membrane selection and optimize passive sampler development.

Development and applications of diffusive gradients in thin films for monitoring pharmaceuticals in surface waters

Pharmaceutical contaminants in surface water have raised significant concerns because of their potential ecological risks. In particular, coronavirus disease 2019 (COVID-19)-related pharmaceuticals can be released to surface water and reduce environmental water quality. Therefore, reliable and robust sampling tools are required for monitoring pharmaceuticals. In this study, passive sampling devices of diffusive gradients in thin films (DGTs) were developed for sampling 35 pharmaceuticals in surface waters. The results demonstrated that hydrophilic-lipophilic balance (HLB) was more suitable for DGT-based devices compared with XAD18 and XDA1 resins. For most pharmaceuticals, the performance of the HLB-DGT devices were independent of pH (5.0-9.0), ionic strength (0.001-0.5 M), and flow velocity (0-400 rpm). The HLB-DGT devices exhibited linear pharmaceutical accumulation for 7 days, and time-weighted average concentrations provided by the HLB-DGT were comparable to those measured by conventional grab sampling. Compared to previous studies, we extended DGT monitoring to include three antiviral drugs used for COVID-19 treatment, which may inspire further exploration on identifying the effects of COVID-19 on ecological and human health.

Validation and application of diffusive gradient in thin-film (DGT) equipped novel cyclodextrin polymer gels for monitoring endocrine disrupting chemicals (EDCs) and environmental risk assessment in the Taihu lake basin

Taihu Lake is the most important drinking water source of the major cities in the Yangtze River Delta. The pollution of endocrine disruptors (EDCs)in Taihu Lake has been increasing recently, the accurate determination is an important guide for predicting its health risks and developing appropriate controls. Monitoring organic pollutants in water using the diffusive gradient in thin film technique (DGT) has attracted much attention due to more accuracy and convenience than the grab sampling methods. In this study, a novel cyclodextrin polymer (CDP) synthesized by the simple and green method in water was taken as an adsorbent for the binding gel. Four endocrine-disrupting chemicals (EDCs), bisphenol A (BPA), 17α-ethinylestradiol (EE2), 17β-estradiol (E2), and estriol (E3), were taken as models to determine the diffusion coefficients (4.68 × 10^-6, 3.38 × 10^-6, 3.34 × 10^-6 and 4.31 × 10^-6 cm²/s) and to test the performance of DGT, such as adsorption capacity and deployment time (1-5 day). The assembled CDP-DGT was adopted to determine four EDCs in a simulated water environment (3-9 of pH, 0.001-0.5 M of ionic strength (IS), and dissolved organic matter (DOM) of 0-20 mg/L). The ability of CDP-DGT sampling was verified in the Jiuxiang River and was carried out for a large-scale field application of in situ sampling EDCs in Taihu Lake basin. The results show that the total EDCs concentration range and the estradiol equivalent concentrations (EEQ) in Taihu Lake and its main rivers are 2.78 ng/L to 11.08 ng/L and 2.62 ng/L to 10.91 ng/L, respectively. The risk quotients (RQs) of all sampling sites in the region were greater than 1, indicating that EDCs pose a serious threat to aquatic organisms in the area. Therefore, the monitoring of EDCs in the Taihu Lake basin should be further strengthened.

Application of diffusive gradients in thin films to determine rare earth elements in surface sediments of Daya Bay, China: Occurrence, distribution and ecotoxicological risks

Known as burgeoning contaminants, the bioavailability of rare earth elements (REEs) can be determined using diffusive gradients in thin films (DGT). As Daya Bay (South China) has been under serious anthropogenic influences, the present study examined the distribution of REEs in surface sediments and their possible ecological risks in the bay. The range of DGT-labile concentrations of REEs (∑REEs) was from 5.67 μg/L to 8.41 μg/L, with an average of 7.34 μg/L. Results of assessment of single REE toxicity revealed that the risk quotient (RQ) values of Y, Ce and Yb were >1, indicating that their potential negative impacts on the nearby environment. However, analysis of the integral toxicity of REE mixtures through assessment of probabilistic ecotoxicological risks showed that there was a negligibly low probability of toxicity of PRE surface sediments to aquatic organisms in the study area.

Pesticides in surface freshwater: a critical review

The objective of this study was to critically review studies published up to November 2021 that investigated the presence of pesticides in surface freshwater to answer three questions: (1) in which countries were the studies conducted? (2) which pesticides are most evaluated and detected? and (3) which pesticides have the highest concentrations? Using the Prisma protocol, 146 articles published from 1976 to November 2021 were included in this analysis: 127 studies used grab sampling, 10 used passive sampling, and 9 used both sampling techniques. In the 45-year historical series, the USA, China, and Spain were the countries that conducted the highest number of studies. Atrazine was the most evaluated pesticide (56% of the studies), detected in 43% of the studies using grab sampling, and the most detected in passive sampling studies (68%). The compounds with the highest maximum and mean concentrations in the grab sampling were molinate (211.38 µg/L) and bentazone (53 µg/L), respectively, and in passive sampling, they were oxyfluorfen (16.8 µg/L) and atrazine (4.8 μg/L), respectively. The levels found for atrazine, p,p'-DDD, and heptachlor in Brazil were higher than the regulatory levels for superficial water in the country. The concentrations exceeded the toxicological endpoint for at least 11 pesticides, including atrazine (Daphnia LC₅₀ and fish NOAEC), cypermethrin (algae EC50, Daphnia and fish LC₅₀; fish NOAEC), and chlorpyrifos (Daphnia and fish LC₅₀; fish NOAEC). These results can be used for planning pesticide monitoring programs in surface freshwater, at regional and global levels, and for establishing or updating water quality regulations.

Determination of diffusion coefficients in agarose and polyacrylamide gels for 112 organic chemicals for passive sampling by organic Diffusive Gradients in Thin films (o-DGT)

The diffusive gradient in thin film technique was recently adapted to organic compounds. The diffusional coefficient (D) is a key parameter needed to calculate the time-weighted average concentration. In this study, two methods are used for D measurement in two gels (agarose and polyacrylamide): the diffusion cell method (D_cell) and the slice stacking method (D_stack). Thus, D were discussed and compared for 112 organic compounds, including pesticides, hormones, and pharmaceuticals. D_stack tends to be higher than D_cell. It could be explained by the presence of a non-negligible diffusive boundary layer thickness in diffusion cell. Consequently, the use of sampling rates (R_S) should be more adequate to determine water concentration, for a given bulk flow velocity. D_stack also corresponds to the diffusion in gel only, allowing the determination of the maximal R_S, and would be considered as a reference value that can be adjusted to in situ conditions, by applying the appropriate DBL thickness. The range and variability of D values found in the literature and obtained in this work were discussed. Relationships between D and compound physicochemical properties (molecular mass, log Dow, polar surface area, van der Waals volume) were investigated. We did not find clear and robust correlation between D and any single physicochemical property, for the set of compounds tested.

Effects of biofouling on the uptake of perfluorinated alkyl acids by organic-diffusive gradients in thin films passive samplers

While organic-diffusive gradients in thin films (o-DGT) passive samplers have been used to assess organic contaminants in water, the effects of biofouling on accurate analyte quantification by o-DGT are poorly understood. We evaluated the effects of biofouling on the uptake of six common perfluoroalkyl substances (PFAS) using a previously developed polyacrylamide-WAX (weak anion exchange) o-DGT without a filter membrane. Linear uptake (R² > 0.91) over 21 days was observed in fouled samplers. The measured sampling rates (R_s) and accumulated masses of PFAS in pre-fouled o-DGT were significantly lower (p < 0.05, 20-39% relative error) than in control-fouled samplers. However, compared to clean o-DGT (no biofouling), the R_s of most PFAS in control-fouled samplers (i.e., those with clean diffusive and binding gels initially) were not affected by biofouling. Under flowing (∼5.8 cm s^-1) and static conditions, the measured diffusive boundary layer (DBL) thicknesses for clean o-DGT were 0.016 and 0.082 cm, respectively, whereas the effective in situ biofilm thicknesses for fouled o-DGT were 0.018 and 0.14 cm, respectively. These results suggest that biofilm growth does not have significant effects on target PFAS sampling by o-DGT under typical flowing conditions (≥2 cm s^-1). However, rapid surface growth of biofilm on o-DGT deployed in quiescent waters over long periods of time may exacerbate the adverse effects of biofilms, necessitating the estimation of biofilm thickness in situ. This study provides new insights for evaluating the capability of o-DGT samplers when biofilm growth can be significant.

In situ monitoring of phthalate esters (PAEs) pollution and environmental risk assessment in Poyang Lake Basin by DGT Technology using cyclodextrin polymer as binding phase

Poyang Lake is the first freshwater lake in China, which is an important drinking water source. In recent years, industrial pollution has led to the increased phthalate acid esters (PAEs) in Poyang Lake. PAEs are a class of typical endocrine disruptors that can accumulate in organisms and interfere with their secretion systems. Thus, the accurate determination of PAEs in Poyang Lake is important for health risk prediction and the development of corresponding control means. Monitoring organic pollutants in water using the diffusive gradient in thin films technique (DGT) has attracted much attention due to more accuracy and convenience than the traditional methods. This study used an inexpensive amphiphilic cyclodextrin polymer (PBCD) as the sorbent for the binding gel. This new binding gel has an ultra-high specific surface area and excellent adsorption performance. Diffusion coefficients of the five PAEs were determined, and the performance of DGT such as adsorption capacity and deployment time (1-4 days) was tested using five PAEs as models. The assembled PBCD-DGT was used to examine the performance in a complex simulated water environment. The sampling capability of PBCD-DGT was verified in Yangshan Lake, and a large-scale field application was conducted in Poyang Lake basin. The results of 11 sampling points showed that the concentration ranges of dimethyl phthalate, diethyl phthalate, diallyl phthalate, dipropyl phthalate, and dibutyl phthalate were 434-2594 ng/L, 40-314 ng/L, 80-527 ng/L, 45-308 ng/L, and ND-182 ng/L, respectively. The health risk index (HI) and ecological risk quotient (RQ) values of PAEs in the Poyang Lake watershed were far below 1, indictating a lower health and ecological risk. Considering that PAEs are bioaccumulative and persistent, it is very necessary to continue to pay attention to its pollution status and health and ecological risk changes in Poyang Lake Basin in the future.

Passive sampling of chlorophenols in water and soils using diffusive gradients in thin films based on β-cyclodextrin polymers

Chlorophenols (CPs) have been listed as priority control pollutants because of their high toxicity and wide range. An In-situ monitoring technique using diffusive gradients in thin films based on porous β-cyclodextrin polymers as binding materials (CDP-DGT), was established to monitor four typical CPs, namely, 4-Chlorophenol (4-CP), 2,4-Dichlorophenol (2,4-DCP), 2,4,5-Trichlorophenol (2,4,5-TCP), 2,4,6-Trichlorophenol (2,4,6-TCP) in water and soils. The performance of CDP-DGT are stable under the conditions of pH 3.5-9.3, ionic strength 0.001-0.500 mol L^-1 and dissolved organic matter concentration 0-20 mol L^-1. The adsorption capacities of CDP-DGT for 4-CP, 2,4-DCP, 2,4,5-TCP, 2,4,6-TCP were 57.80 μg cm^-2, 98.82 μg cm^-2, 95.69 μg cm^-2 and 98.91 μg cm^-2, respectively. The time-average weighted concentrations of four CPs determined by CDP-DGT at Sanjiangkou wharf (Yangtze river, China) were consistent with the results of grab sampling, indicating the feasibility of CDP-DGT application in actual water. In addition, the distribution of CPs in the red soil of Kunming and paddy soil of Yixing were also studied by CDP-DGT, and the desorption kinetics in the two soils were analyzed with the DIFS model. The higher the soil organic matter content is, the more CPs are distributed in the soil solid phase. CPs in both soils can be partially resupplied to soil solution from the soil solid phase and the higher the partition coefficient for labile CPs is, the stronger the supplement capacity is.

Development and field evaluation of the organic-diffusive gradients in thin-films (o-DGT) passive water sampler for microcystins

The presence of microcystins (MCs) in waterbodies requires a simple and reliable monitoring technique to characterize better their spatiotemporal distribution and ecological risks. An organic-diffusive gradients in thin films (o-DGT) passive sampler based on polyacrylamide diffusive gel and hydrophilic-lipophilic balance (HLB) binding gel was developed for MCs in water. The mass accumulation of three MCs (MC-LR, -RR, and -YR) was linear over 10 days (R² ≥ 0.98). Sampling rates (2.68-3.22 mL d^-1) and diffusion coefficients (0.90-1.08 × 10^-6 cm² s^-1) of three MCs were obtained at 20 °C. Two different passive samplers, o-DGT and the Solid Phase Adsorption Toxin Tracking device (SPATT), were co-deployed to estimate MC levels at three lakes in California, USA. Measured total MC concentrations were up to 10.9 μg L^-1, with MC-LR the primary variant at a measured maximum concentration of 2.74 μg L^-1. Time-weighted average MC concentrations by o-DGT were lower than grab water samples, probably because grab sampling measures both dissolved and particulate phases (i.e., MCs in cyanobacteria). Passive water samplers by design can only measure dissolved-phase MCs, which are considerably less during the cyanobacteria-laden periods observed. Both o-DGT and grab samples gave comparable results for three MC variants at low levels of MCs, e.g., <0.1 μg L^-1. o-DGT showed a higher correlation with grab sampling than SPATT did. This study demonstrates that o-DGT can be effectively used for monitoring and evaluation of dissolved MCs in waters.

A critical review of diffusive gradients in thin films technique for measuring organic pollutants: Potential limitations, application to solid phases, and combination with bioassays

Diffusive gradient in thin films (DGT) for organics has received considerable attention for studying the chemical dynamics of various organic pollutants in the environment. This review investigates current limitations of DGT for organics and identifies several research gaps for future studies. The application of a protective outer filter membrane has been recommended for most DGT applications, however, important questions regarding longer lag times due to significant interaction or adsorption of specific groups of compounds on the outer membrane remain. A modified DGT configuration has been developed that uses the diffusive gel as the outer membrane without the use of an extra filter membrane, however use of this configuration, while largely successful, remains limited. Biofouling has been a concern when using DGT for metals; however, effect on the performance of DGT for organics needs to be systemically studied. Storage stability of compounds on intact DGT samplers has been assessed in select studies and that data is synthesized here. DGT has been used to describe the kinetic desorption of antibiotics from soils and biosolids based on the soil/biosolid physical-chemical characteristics, yet applications remain limited and requires further research before wide-scale adoption is recommended. Finally, DGT for organics has been rarely, albeit successfully, combined with bioassays as well as in vivo bioaccumulation studies in zebrafish. Studies using DGT combined with bioassays to predict the adverse effects of environmental mixtures on aquatic or terrestrial biota are discussed here and should be considered for future research.

Multisite Calibration of a Microporous Polyethylene Tube Passive Sampler for Quantifying Drugs in Wastewater

Passive sampling approaches to monitor licit and illicit drugs of concern in wastewater shows promise as a supplementary sampling technique to grab sampling when conventional composite autosampling may not be possible. Recent studies have assessed the applicability of passive sampling at a single wastewater treatment plant (WWTP). However, it remains unknown whether a single-site calibration can be applied to other WWTPs. This study evaluated the in situ calibration of microporous polyethylene tube passive samplers (MPTs) against simultaneously collected composite samples for 22 different WWTPs. Samples were analyzed for methylamphetamine, amphetamine, hydroxycotinine, cotinine, benzoylecgonine, 3,4-methylenedioxymethamphetamine, and noroxycodone. Estimated rates of chemical uptake (sampling rates) were calculated using the mass accumulated in the samplers, the concentration measured in composite samples, and the duration of deployment. The estimated sampling rates were consistent between WWTPs (>90% within a factor of two) and ranged from 5 mL day^-1 (amphetamine) to 9 mL day^-1 (noroxycodone). The samplers were effective at estimating analyte concentrations, with 77% of results having a normalized difference to 24 h composite samples of below 30%. Our study suggests that MPT passive samplers provide a tool for the spatiotemporal monitoring of drug use where automated integrative sampling techniques may not be feasible.

Tetrafluoroterephthalonitrile-crosslinked β-cyclodextrin polymer as a binding agent of diffusive gradients in thin-films for sampling endocrine disrupting chemicals in water

β-Cyclodextrin (β-CD) is an inexpensive and reproducible material derived from corn starch. It is possible that tetrafluoroterephthalonitrile-crosslinked β-cyclodextrin polymer (TFN-CD), a cheap but efficient adsorbent, could be a suitable binding agent for use in the passive sampling technique, diffusive gradients in thin-films (DGT). Herein, the TFN-CD binding gel was prepared and then evaluated as the binding phase of DGT to sample six endocrine disrupting chemicals (EDCs) in water. The TFN-CD dispersed uniformly in the binding gel due to its hydrophilicity. The quantitative recoveries (99.3%-106%) of EDCs from the TFN-CD binding gel could be conveniently achieved by ultrasonic extraction using 5 mL methanol for 10 min. Compared with the excellent HLB (hydrophilic-lipophilic-balanced resin) binding gel, the TFN-CD binding gel had comparable or even faster adsorption kinetics, although the equilibrium adsorption capacity was slightly lower. The effective adsorption capacities of TFN-CD-based DGT (TFN-CD-DGT) were roughly estimated to enable a 7-days deployment in EDC solution of 25.7-30.0 μg L^-1. Studies of influencing factors showed that the ionic strength (0-0.5 M), pH (3.73-9.13), dissolved organic matter (0-20 mg L^-1) and long-term storage (204 days) had negligible influence on the performance of TFN-CD-DGT. Finally, the TFN-CD-DGT was successfully used to record sudden increases in bulk concentrations during simulated discharge events in pond water. These results demonstrate that TFN-CD is a suitable binding agent for sampling of EDCs, and the low cost of TFN-CD could be conducive to the application of DGT in large-scale sampling.

Crushed recycled glass as a substrate for constructed wetland wastewater treatment: a case study of its potential to facilitate pharmaceutical removal

The use of recycled glass as a substrate for constructed wetlands was assessed through two studies. The first study examined the dissipation of atenolol, carbamazepine, and sulfamethoxazole in mesocosm-modeled wetlands using glass or limestone gravel as substrates, with or without cattails (Typha spp.). Following pseudo-first-order kinetics, atenolol dissipated the fastest from the water surface of the mesocosms (t_1/2~1 day), followed by sulfamethoxazole (t_1/2~14 days), and carbamazepine (t_1/2~48 days), with no significant differences across treatments. Increased half-lives were observed at greater depth, likely due to light screening. A Monte Carlo sensitivity analysis diagnosed sunlight absorption rates and second-order hydroxyl-mediated indirect photolysis rates to be the main sources of uncertainty in our dissipation rate estimates, compared to our observed rates. The second study examined in situ pharmaceutical removal in tertiary pilot-scale subsurface filters made of crushed recycled glass or sand in a wastewater treatment facility in Manitoba, Canada. Glass and sand showed no significant differences for pharmaceutical removals; atenolol and metoprolol were removed below limits of detection, while carbamazepine and sulfamethoxazole persisted over a retention time of 24 h. Overall, recycled glass performed similarly to traditional substrates for wetland-based wastewater treatment.

Development and application of diffusive gradients in thin-films for in situ sampling of the bitterest chemical - denatonium benzoate in waters

Denatonium benzoate (DB), a commonly used bitter agent in numerous products, has recently been recognized as a waterborne contaminant due to concern about its potential persistence, mobility and toxicity (PMT). However, its occurrence, levels and fate in global aquatic environments are largely unknown. In this study, a new sampling method, based on diffusive gradients in thin films (DGT) with mixed-mode cation exchange (MCX) as the binding agent, was developed for measuring DB in waters. MCX shows a rapid adsorption and high capacity for DB. DB is linearly accumulated by MCX-DGT. pH (6-8), ionic strength (0.01-0.5 M), or DOM (0-10 M) do not show any significant effect on the MCX-DGT performance, confirming its reliability. The DGT measurements in a wastewater treatment plant (WWTP) are comparable to those by paralleled grab sampling. The field results suggest DB is persistent in WWTPs and could be a potential domestic wastewater indicator. Therefore, MCX-DGT is a promising technique for understanding the environmental occurrence, levels and fate of DB. This is a first report of using DGT for DB monitoring and of DB occurrence in Chinese environments. Further exploration of DGT as a reliable passive monitoring tool for a wide range of PMT substances in different applications is warranted.

Field application of a novel active-passive sampling technique for the simultaneous measurement of a wide range of contaminants in water

A first test of the field capabilities of a novel in situ sampling technique combining active and passive sampling (APS) was conducted in the sea. The proof-of-concept device uses a pump to draw water into a diffusion cell where dissolved target substances are accumulated onto sorbents which are selective for different classes of contaminants (i.e., metal cations, polar and non-polar organic compounds), simultaneously. A controlled laminar flow established in the diffusion cell enables measurements of contaminant concentrations that are fully independent from the hydrodynamic conditions in the bulk solution. APS measurements were consistent with those obtained using conventional passive sampling techniques such as organic diffusive gradients in thin films (o-DGT) and silicone rubber (SR) samplers (generally < 40% difference), taking into account the prevailing hydrodynamic conditions. The use of performance reference compounds (PRC) for hydrophobic contaminants provided additional information. Field measurements of metal ions in seawater showed large variability due to issues related to the device configuration. An improved field set-up deployed in supplementary freshwater mesocosm experiments provided metal speciation data that was consistent with passive sampling measurements (DGT), taking into account the hydrodynamic conditions. Overall, the results indicate that the APS technique provides a promising approach for the determination of a wide range of contaminants simultaneously, and independently from the hydrodynamic conditions in the bulk solution.

Development and Applications of Novel DGT Passive Samplers for Measuring 12 Per- and Polyfluoroalkyl Substances in Natural Waters and Wastewaters

Extensive and long-term use of per- and polyfluoroalkyl substances (PFASs) has caused their widespread distribution in aquatic systems. A new diffusive gradients in thin-films (DGT) passive sampling method based on weak anion exchanger (WAX) binding layer is developed here for monitoring five perfluoroalkyl carboxylic acids (PFCAs), five perfluoroalkanesulfonic acids (PFSAs) and two PFASs (6:2 FTSA and GenX) in waters. Performance of WAX-DGTs was independent of environmental conditions, namely pH (3.03-8.96), ionic strength (1-500 mM), and DOM content (4-30 mg L^-1). Diffusion coefficients (D) of the 12 PFASs in the diffusive gels were measured, 9 for the first time. Linear correlations between D and perfluoroalkyl chain lengths (CF₂) were established to obtain D for congener chemicals with the similar functional group and structure. The binding capacity of the WAX-DGT sampler was at least 440 μg PFASs per sampler, sufficient for applications in waters across a wide range of conditions and PFASs concentrations. Successful applications of WAX based DGT samplers in a wastewater treatment plant (WWTP) and three rivers has demonstrated that DGT is a powerful tool for monitoring, surveillance and research of these 12 PFASs in aquatic systems, and can be extended to wider suites of PFs in future.

Field evaluation of diffusive gradients in thin-film passive samplers for wastewater-based epidemiology

There is a need for a simple water sampling technique to enable routine monitoring of community drug consumption through wastewater-based epidemiology (WBE). This study investigates the potential use of diffusive gradients in thin films to sample organic compounds (o-DGT) for WBE. Three types of resin gels (HLB, XAD 18, and XDA-1) within o-DGT samplers each were deployed in triplicate at the inlets of two sewage treatment plants of Southern Asian cities. The target compounds included 15 illicit drugs and 18 antibiotics. A comprehensive evaluation was undertaken regarding each resin's ability to accumulate the target compounds and accuracy by comparing active samples. The organic compounds accumulated on each resin gel were characterised at the molecular level using Fourier transform ion-cyclotron-resonance mass spectrometry (FT-ICR MS). The results showed that the HLB resin performed better than the XAD 18 and XDA-1 resins. Based on calculations using the HLB-DGT data, methamphetamine and heroin were the two most popular illicit drugs consumed among the studied populations, and were followed by ketamine and codeine, which agreed well with the authoritative reports and reference data. The total drug consumption in Hanoi was one order of magnitude higher than that in Guangzhou, thus implying a probably more serious drug situation in the former. Overall, the findings of this study demonstrate that o-DGT passive samplers are a promising tool for WBE studies, particularly at WWTPs or in urban streams where an automatic sampler for taking composite water samples is absent.

Limitations of Integrative Passive Samplers as a Tool for the Quantification of Pharmaceuticals in the Environment - A Critical Review with the Latest Innovations

This review starts with a presentation of the theory of kinetic uptake by passive sampling (PS), which is traditionally used to distinguish between integrative and equilibrium samplers. Demonstrated limitations of this model for the passive sampling of pharmaceuticals from water were presented. Most notably, the contribution of the protective membrane in the resistance to mass transfer of lipophilic analytes and the well documented effect of external parameters on sampling rates contributed to the greatest uncertainty in PS application. The diffusion gradient in thin layer (DGT) technique seems to reduce the effect of external parameters (e.g., flow rate) to some degree. The laboratory-determined integrative uptake periods over defined sampler deployments was compared, and the discrepancy found suggests that the most popular Polar Organic Chemical Integrative Sampler (POCIS) could in some cases utilized as an equilibrium sampler. This assertion is supported by own calculations for three pharmaceuticals with extremely different lipophilic characters. Finally, the reasons performance reference compounds (PRCs) are not recommended for the reduction in uncertainty of the TWAC found by adsorptive samplers were presented. It was concluded that techniques of passive sampling of pharmaceuticals need a new uptake model to fit the current situation.

Comparative field study on bioassay responses and micropollutant uptake of POCIS, Speedisk and SorbiCell polar passive samplers

Routine water quality monitoring is generally performed with chemical analyses of grab samples, which has major limitations. First, snapshot samples will not give a good representation of the water quality. Second, it is not sufficient to analyze only a limited number of (priority) pollutants. These limitations can be circumvented by an alternative environmental risk assessment that combines time-integrated passive sampling (PS) with effect-based methods. This study aimed to select which of three polar PS devices was best suited for effect-based monitoring strategies. In the first part of this study, Speedisk, SorbiCell and POCIS polar PS devices were compared by simultaneous deployment at five sites. Chemical analyses of 108 moderately polar compounds (-1.82 < log D < 6.28) revealed that highest number of compounds, with the widest range of log K_OW, log D and pKa, were detected in extracts of POCIS, followed by Speedisk. SorbiCell samplers accumulated the lowest numbers and concentrations of compounds, so they were not further investigated. In a follow-up study, bioassay responses were compared in extracts of POCIS and Speedisk devices deployed at eight sites. The passive sampler extracts were subjected to bioassays for non-specific toxicity, endocrine disruption, and antibiotics activities. More frequent and higher responses were induced by POCIS extracts, leading to more exceedances of effect-based trigger values for environmental risks. As POCIS outperformed Speedisk, it is better suited as PS device targeting polar compounds for semi-quantitative effect-based water quality monitoring.

In situ calibration of polar organic chemical integrative sampler (POCIS) for monitoring of pharmaceuticals in surface waters

POCIS is the most widely applied passive sampler of polar organic substances, because it was one of the first commercially available samplers for that purpose on the market, but also for its applicability for a wide range of substances and conditions. Its main weakness is the variability of sampling performance with exposure conditions. In our study we took a pragmatic approach and performed in situ calibration for a set of 76 pharmaceuticals and their metabolites in five sampling campaigns in surface water, covering various temperature and flow conditions. In individual campaigns, R_S were calculated for up to 47 compounds ranging from 0.01 to 0.63 L d^-1, with the overall median value of 0.10 L d^-1. No clear changes of R_S with water temperature or discharge could be found for any of the investigated substances. The absence of correlation of experimental R_S with physical-chemical properties in combination with the lack of mechanistic understanding of compound uptake to POCIS implies that practical estimation of aqueous concentrations from uptake in POCIS depends on compound-specific experimental calibration data. Performance of POCIS was compared with grab sampling of water in seven field campaigns comprising multiple sampling sites, where sampling by both methods was done in parallel. The comparison showed that for 25 of 36 tested compounds more than 50% of POCIS-derived aqueous concentrations did not differ from median of grab sampling values more than by a factor of 2. Further, for 30 of 36 compounds, more than 80% of POCIS data did not differ from grab sampling data more than by a factor of 5. When accepting this level of accuracy, in situ derived sampling rates are sufficiently robust for application of POCIS for identification of spatial and temporal contamination trends in surface waters.

Calibration of organic-diffusive gradients in thin films (o-DGT) passive samplers for perfluorinated alkyl acids in water

The application of the organic-diffusive gradients in thin films (o-DGT) passive sampling technique for the monitoring of per- and polyfluoroalkyl substances (PFAS) in the environment is still limited. Six common PFAS with different chain lengths were evaluated in water by o-DGT. Measured diffusion coefficients (D) in agarose and polyacrylamide diffusive gels ranged from 4.55-8.63 × 10^-6 cm² s^-1 and 3.85-7.00 × 10^-6 cm² s^-1 at 23 °C, respectively. Experimental sampling rates (Rs) for both agarose- and polyacrylamide-WAX sampler configurations were within 22% relative error of D-based Rs for four of the PFAS. Larger differences for perfluorobutanesulfonic acid (PFBS) and perfluoroundecanoic acid (PFUnDA) ranged from 36% to 56%. In general, in-situ Rs can be predicted using measured D-values for perfluorinated alkyl acids. The mass accumulation of six PFAS in two o-DGT configurations was linear over 21 days (R² ≥ 0.97). Diffusion and uptake of o-DGT depended on the gel type and specific PFAS. Field demonstrations of o-DGT with WAX and HLB binding gels and polyacrylamide diffusive gels (not prone to biodegradation) found 0.3-19.5 ng L^-1 of PFAS in rivers near industrial areas around Guangzhou and Foshan, China, with no apparent differences between the two co-deployed samplers. This study demonstrates that the configurations of o-DGT tested provide a cost-effective monitoring tool for measuring perfluorinated alkyl acids in aquatic systems, in particular the four PFAS for which reasonable correlations were observed.

In situ measurement of synthetic musks in wastewaters using diffusive gradients in thin film technique

Synthetic musks (SMs) are used extensively in household and personal care products and have acted significant concerns due to their environmental impacts and potential health effects. Here, we present a passive sampling approach based on diffusive gradients in thin films (DGT) for in situ measurement of SMs in urban wastewaters. XAD-2 binding gel, which has a rapid binding rate and high elution efficiency, was used in DGT device for the accumulation of six polycyclic musks and three nitro musks. The diffusion coefficients (D and D_NL) of the SMs through agarose gel without and with a nylon filter membrane were 3.37-4.49 and 1.48-4.41 ×10^-6cm² s^-1. The filter membrane caused an ~3 h lag phase and slowed the diffusion rates of the SMs through the diffusive phase. Solution pH (4.30-8.92), ionic strength (0.0001-0.5 M) and dissolved organic matter (0-20 mg L^-1) showed no obvious influence on uptake of the SMs in DGT. The measured average SM concentrations in the effluent of wastewater treatment plants ranged from 0.45-696 ng/L for DGT deployment, without obvious membrane biofouling, and they were comparable to the concentrations determined by grab sampling. These results confirmed that the present method is reliable and convenient for in situ measurement of semivolatile hydrophobic SMs in complicated waters and is an available tool to investigate the environmental behaviors of SMs in the environment.

A year-long passive sampling of phenolic endocrine disrupting chemicals in the East River, South China

The occurrence of endocrine disrupting chemicals (EDCs) in the aquatic environment is a global concern. In this study, we employed two different passive samplers Diffusive Gradients in Thin-films (DGT) and Chemcatcher for in situ measurement of 8 phenolic EDCs in the East River of the Pearl River system over one-year. These data were assessed alongside results from traditional grab sampling. Six chemicals (4tOP, 4NP, BPA, E1, EE2 and DES) were regularly detected in the water samples, of which the three phenols (i.e. 4tOP, 4NP and BPA) were in all samples and at high concentrations (0.4-1040 ng/L for 4tOP, 2.6-58500 ng/L for NP and 11.4-123300 ng/L for BPA). Fewer target chemicals were detected in both passive samplers, with only 4tOP, 4NP and BPA found in most samplers; E1 and DES were occasionally measurable above detection limits. The higher (by about a factor of 2-3) measurements provided by DGT compared to Chemcatcher could be attributed to the effect of the diffusive boundary layer on Chemcatcher uptake or the strong adsorption of target chemicals on the Chemcatcher PES filter. The temporal trends of EDC monthly loadings indicated that they were from different sources and that WWTPs were not effective in EDC removal and/or there was still some untreated wastewater discharged into the rivers.

Fungal bioremediation of soil co-contaminated with petroleum hydrocarbons and toxic metals

Abstract

Much research has been carried out on the bacterial bioremediation of soil contaminated with petroleum hydrocarbons and toxic metals but much less is known about the potential of fungi in sites that are co-contaminated with both classes of pollutants. This article documents the roles of fungi in soil polluted with both petroleum hydrocarbons and toxic metals as well as the mechanisms involved in the biotransformation of such substances. Soil characteristics (e.g., structural components, pH, and temperature) and intracellular or excreted extracellular enzymes and metabolites are crucial factors which affect the efficiency of combined pollutant transformations. At present, bioremediation of soil co-contaminated with petroleum hydrocarbons and toxic metals is mostly focused on the removal, detoxification, or degradation efficiency of single or composite pollutants of each type. Little research has been carried out on the metabolism of fungi in response to complex pollutant stress. To overcome current bottlenecks in understanding fungal bioremediation, the potential of new approaches, e.g., gradient diffusion film technology (DGT) and metabolomics, is also discussed.

Key points

• Fungi play important roles in soil co-contaminated with TPH and toxic metals.

• Soil characteristics, enzymes, and metabolites are major factors in bioremediation.

• DGT and metabolomics can be applied to overcome current bottlenecks.

In Situ Catchment Scale Sampling of Emerging Contaminants Using Diffusive Gradients in Thin Films (DGT) and Traditional Grab Sampling: A Case Study of the River Thames, UK

The in situ passive sampling technique, diffusive gradients in thin films (DGT), confronts many of the challenges associated with current sampling methods used for emerging contaminants (ECs) in aquatic systems. This study compared DGT and grab sampling for their suitability to screen and monitor ECs at the catchment scale in the River Thames system (U.K.) and explored their sources and environmental fate. The ubiquitous presence of endocrine disrupting chemicals, parabens, and their metabolites is of concern. This study is the first to report organophosphate esters (OPEs) in the study area. TEP (summer 13-160 and winter 18-46, ng/L) and TCPP (summer 242-4282 and winter 215-854, ng/L) were the main OPEs. For chemicals which were relatively stable in the rivers, DGT and grab sampling were in good agreement. For chemicals which showed high variation in water bodies, DGT provided a better integral of loadings and exposure than grab sampling. DGT was not as sensitive as grab sampling under the procedures employed here, but there are several options to improve it to give comparable/better performance. DGT samples require shorter preparation time for analysis in the laboratory than grab samples. Overall, DGT can be a powerful tool to characterize ECs throughout a large dynamic water system.

Sampling Rate of Polar Organic Chemical Integrative Sampler (POCIS): Influence Factors and Calibration Methods

As a passive sampling device, the polar organic chemical integrative sampler (POCIS) has the characteristics of simple operation, safety, and reliability for assessing the occurrence and risk of persistent and emerging trace organic pollutants. The POCIS, allowing for the determination of time-weighted average (TWA) concentration of polar organic chemicals, exhibits good application prospects in aquatic environments. Before deploying the device in water, the sampling rate (Rs), which is a key parameter for characterizing pollutant enrichment, should be determined and calibrated accurately. However, the Rs values strongly depend on experimental hydrodynamic conditions. This paper provides an overview of the current situation of the POCIS for environmental monitoring of organic pollutants in an aquatic system. The principle and theory of the POCIS are outlined. In particular, the effect factors such as the ambient conditions, pollutant properties, and device features on the Rs are analyzed in detail from aspects of impact dependence and mechanisms. The calibration methods of the Rs under laboratory and in situ conditions are summarized. This review offers supplementary information on comprehensive understanding of mechanism and application of the POCIS. Nevertheless, the Rs were impacted by a combined effect of solute–sorbent–membrane–solution, and the influence extent of each variable was still unclear. On this basis, the ongoing challenges are proposed for the future application of the POCIS in the actual environment, for instance, the need for this device to be improved in terms of quantitative methods for more accurate measurement of the Rs.

Detection of pharmaceuticals in wastewater effluents-a comparison of the performance of Chemcatcher® and polar organic compound integrative sampler

Chemcatcher^® and POCIS passive sampling devices are widely used for monitoring polar organic pollutants in water. Chemcatcher^® uses a bound Horizon Atlantic™ HLB-L sorbent disk as receiving phase, whilst the POCIS uses the same material in the form of loose powder. Both devices (n = 3) were deployed for 21 days in the final effluent at three wastewater treatment plants in South Wales, UK. Following deployment, sampler extracts were analysed using liquid chromatography time-of-flight mass spectrometry. Compounds were identified using an in-house database of pharmaceuticals using a metabolomics workflow. Sixty-eight compounds were identified in all samplers. For the POCIS, substantial losses of sorbent (11-51%) were found during deployment and subsequent laboratory analysis, necessitating the use of a recovery factor. Percentage relative standard deviations varied (with 10 compounds exceeding 30% in both samplers) between individual compounds and between samplers deployed at the three sites. The relative performance of the two devices was evaluated using the mass of analyte sequestered, measured as an integrated peak area. The ratio of the uptake of the pharmaceuticals for the POCIS versus Chemcatcher^® was lower (1.84x) than would be expected on the basis of the ratio of active sampling areas (3.01x) of the two devices. The lower than predicted uptake may be attributable to the loose sorbent material moving inside the POCIS when deployed in the field in the vertical plane. In order to overcome this, it is recommended to deploy the POCIS horizontally inside the deployment cage.

Evaluation of cold-weather wastewater nitrification technology for removal of polar chemicals of emerging concern from rural Manitoba wastewaters

Aerated lagoons, typically used by small communities, often provide limited removal of wastewater nutrients. Given increasingly stringent wastewater standards, it is imperative that effective, but economical and easy-to-operate, treatment technologies be developed. The Submerged Attached Growth Reactor (SAGR®) is a treatment process developed to perform nitrification near freezing temperatures. Previous tests on full-scale installations have shown that SAGR could consistently remove ammonia to below current Canadian standards and provide additional total suspended solids and biochemical oxygen demand removal. In this study, we evaluated removal of polar chemicals of emerging concern (CECs), including pharmaceuticals, personal care products, and pesticides, at SAGR installations in two Manitoba First Nations communities (MCN and LPFN) under cold winter conditions. Both showed some removal of diclofenac, naproxen, clarithromycin, metoprolol, and trimethoprim, likely by biotransformation. Average naproxen removal was 21% (2.53 × 10³ ng L^-1) in MCN and 64% (1.58 × 10³ ng L^-1) in LPFN. Atenolol was well-removed by SAGR, by 80% on average (range of 64%-94%). Clarithromycin, metoprolol, and trimethoprim removal was similar within and between systems, ranging from 54% to 76% (30.8-3.07 × 10² ng L^-1 removed). Carbamazepine was detected in nearly all samples, but was not well-removed, consistent with other treatment studies. Overall, results showed that SAGR technology could moderately remove CECs, while providing the designed treatment performance for other parameters. This work will help to improve our understanding of wastewater treatment in small and/or remote communities with limited infrastructure and challenging cold-weather conditions.

Monitoring Organic Pollutants in Waters Using the Diffusive Gradients in the Thin Films Technique: Investigations on the Effects of Biofouling and Degradation

The diffusive gradients in thin films (DGT) passive sampling technique has been increasingly used to provide time-weighted average concentrations of the biorelevant fraction of organic contaminants in waters, with high spatial and temporal resolutions at low cost. This study was tested for the effects of biofouling and compound degradation/loss during sample handling/storage on the DGT measurement of a range of emerging organic pollutants. Biofouling was tested using biofilms collected from the influent and effluent of a typical urban wastewater treatment plant. Most (85%) target compounds showed no detectable effect on the DGT measurement when 8- and 15-day biofouled membrane filters were used. Four storage methods were designed to test for within-sampler degradation/loss for up to 2 months. Intact samplers can be simply stored in polyethylene bags at ambient temperature (18-26 °C) with most compounds stable (mass loss <20%) for at least 1 week. Keeping intact samplers at 4 °C or binding gels in solvent gave good recoveries, with most chemicals being stable for up to 2 months, although the best results were obtained when binding gels were kept in solvent at 4 °C. Recommendations are made for sample handling and storage of DGT samplers used for determination of trace organics in monitoring and surveillance campaigns.

Performance of the organic-diffusive gradients in thin-films passive sampler for measurement of target and suspect wastewater contaminants

Although passive sampling is widely accepted as an excellent tool for environmental monitoring, their integration with suspect or non-targeted screening by high-resolution mass spectrometry has been limited. This study describes the application of the organic-diffusive gradients in thin-films (o-DGT) passive sampler as a tool for accurate measurement of both targeted and suspect polar organic contaminants (primarily pharmaceuticals) in wastewater. First, performance of o-DGT was assessed alongside the polar organic chemical integrative sampler (POCIS) and active sampling at two wastewater treatment facilities using targeted analyses. Overall, water concentrations measured by o-DGT, POCIS, and 24-hr integrative active samples were in good agreement with each other. There were exceptions, including a systematic difference between o-DGT and POCIS at certain sites that we propose was a result of site-specific conditions and a difference in sampling rates between the two techniques. The second component of this work involved suspect screening of the o-DGT extracts using high-resolution, high mass accuracy quadrupole time-of-flight mass spectrometry (QTOF). Lamotrigine, venlafaxine, and des-methylvenlafaxine were three suspect compounds identified and selected as proof-of-concept case studies to determine the feasibility and accuracy of o-DGT for estimating water concentrations based upon predicted sampling rates using a previously validated o-DGT diffusion model. Semi-quantification of the suspect compounds was conducting using an average surrogate response factor based on the suite of compounds measured by the targeted analyses. This, combined with the modelled sampling rates provided time-weighted average wastewater concentrations of the identified suspects within a factor of 2 of the true value, confirmed by isotope dilution with mass labelled internal surrogates. To the knowledge of the authors, this work is the first to demonstrate the utility of the o-DGT passive sampler as a potential environmental screening tool that can be integrated into the rapidly advancing field of non-targeted high resolution mass spectrometry.

Wastewater sources of per- and polyfluorinated alkyl substances (PFAS) and pharmaceuticals in four Canadian Arctic communities

Effective removal of organic contaminants in wastewater effluent poses a challenge to small communities worldwide, particularly in the Arctic due to infrastructure challenges and harsh climates. To understand better the efficacy of current treatment options and risks posed by pharmaceuticals and pesticides on receiving waters in the Arctic, four representative human communities in Nunavut, Canada were evaluated. Per- and polyfluorinated alkyl substances (PFASs) were also investigated in one community. These communities have treatment ranging from primary lagoons, engineered wetlands, and natural lakes. Pharmaceuticals and pesticides were measured using the organic diffusive gradients in thin film (o-DGT) passive sampler in summer 2018. Of the 34 compounds studied, seven pharmaceuticals were found at least once: atenolol, carbamazepine, metoprolol, naproxen, sulfapyridine, sulfamethoxazole, and trimethoprim. With the exception of 5210 ng naproxen/L in Iqaluit, most receiving waters showed negligible amounts of contamination. Iqaluit had the poorest overall system performance while Baker Lake had the best. Measured pharmaceutical concentrations do not appear to pose a significant acute hazard to receiving waters at this time, based on known toxicological endpoints. PFAS concentrations were found to be over 100-fold greater in Cambridge Bay wastewater than previously reported Arctic seawater. Results suggest that wastewater may be an important point source of PFASs in Arctic communities. The o-DGT passive samplers performed well in marine Arctic settings. We recommend further testing of wastewater efficiencies in Arctic communities along with evaluations of seasonal variations.

Adaptation of diffusive gradients in thin films technique to sample organic pollutants in the environment: An overview of o-DGT passive samplers

The adaptation of the diffusive gradients in thin films technique (DGT) to sample organic pollutants in the environment, called o-DGT has been performed since 2011 for various types of organic compounds (e.g. pesticides, pharmaceuticals, hormones, endocrine disrupting chemicals, household and personal care products). To sample these different compounds, configuration of the samplers (mainly receiving phase and diffusive gel) has to be adapted. Up-to-date, sampling of 142 organic compounds by this passive sampler have been tested. This review provides the state-of-art of o-DGT passive sampler development, describing theory and modelling, calibration, configuration of the devices, and field applications. The most used configurations were agarose-XAD-18 and agarose-HLB configuration. o-DGT can be used to sample soils and most of natural waters (range of pH 4-9 and ionic strength 0.001-0.1 M). This review discusses current limitation of o-DGT in light of the feedback of DGT use to sample inorganic contaminants. It mainly concern the low sampling rates currently obtained by o-DGT compared to other passive samplers. This weakness could be compensated in the future with new sampler's design allowing an increase in exposure area.

Coupling mesoporous imprinted polymer based DGT passive samplers and HPLC: A new tool for in-situ selective measurement of low concentration tetrabromobisphenol A in freshwaters

Accurate measurement of tetrabromobisphenol A (TBBPA) is very important because of its widespread environmental pollution. Diffusive gradients in thin films technique (DGT), an in-situ passive sampling method, is regarded as a reliable and robust measurement technique. A new DGT technique based on mesoporous imprinted polymer was combined with high-pressure liquid chromatography (HPLC) method for sampling, preconcentration and monitoring low concentration TBBPA in natural waters. The diffusion coefficient of TBBPA through the diffusive gel was measured by diffusion cell test and simulated using mathematical expression. The effects of different ambient conditions were tested under laboratory conditions and the performance of DGT sampler was validated in natural waters. The diffusion coefficient of TBBPA in the diffusive gel was measured as 2.18 × 10^-6 cm² s^-1 and simulated as in the range 1.41-3.48 × 10^-6 cm² s^-1 by Amsden model. Comparison of experimental and theoretical data, the validity of the experimental method can be verified by the mathematical model. The binding agent with mesoporous imprinted polymer showed selective affinity to TBBPA and its adsorption rate met the requirement of DGT device. The DGT method detection limit was at the level of ng L^-1 for 7 days deployment. DGT sampler was suitable for application in aquatic environment with a range of pH (4.5-7.6), ionic strength (1 × 10^-4 - 0.5 mol L^-1), and dissolved organic matter (DOM) concentration (0-10 mg C L^-1). The coupling method of DGT and HPLC was a promising technique for in situ sampling, preconcentration and monitoring low concentration TBBPA in most typical natural waters.

Development and Application of the Diffusive Gradients in Thin-Films Technique for Measuring Psychiatric Pharmaceuticals in Natural Waters

Psychiatric pharmaceuticals are widely distributed in the aquatic environment and have attracted recent attention due to their potential for environmental effects. A robust and reliable in situ passive sampling approach, the diffusive gradients in thin-films (DGT) technique, is developed here to measure 14 psychiatric pharmaceuticals. A new binding material, mixed-mode cation exchange resin (Poly-Sery MCX, 40 μm, CNW, Germany), was used for the first time in DGT and compared to XAD and HLB. Reliable elution efficiencies of the pharmaceuticals from the binding gels were obtained in methanol/ammonia, and diffusion coefficients for all the compounds were determined. The influence of diffusive layer thickness (0.515-2.015 mm), deployment time (3-168 h), and important environmental conditions-pH (3.02-9.45), ionic strength (0.0001-0.5 M), and dissolved organic matter (0-20 mg L^-1)-were evaluated. The capacity of XAD, HLB, and MCX gels for binding all the test pharmaceuticals was ∼335 μg per disc, meaning that DGT could theoretically be deployed for over 30 months if there are no competitive effects or confounding factors. The uptake kinetics of psychiatric pharmaceuticals onto MCX gel were much faster than those onto XAD and HLB gels in the first hour. DGT measured concentrations of test pharmaceuticals at two sample points in a river (over 6 days) were comparable to those obtained by grab sampling. This study demonstrates the accuracy and reliability of DGT for measuring psychiatric pharmaceuticals across a wide range of freshwater conditions found in the natural environment.

Development of a Passive Sampling Technique for Measuring Pesticides in Waters and Soils

It is essential to monitor pesticides in the environment to help ensure water and soil quality. The diffusive gradients in thin-films (DGT) technique can measure quantitative in situ labile (available) concentrations of chemicals in water, soil, and sediments. This study describes the systematic development of the DGT technique for nine current pesticides, selected to be representative of different classes with a wide range of properties, with two types of resins (HLB (hydrophilic-lipophilic-balanced) and XAD 18) as binding layer materials. The masses of pesticides accumulated by DGT devices were proportional to the deployment time and in inverse proportion to the thickness of the diffusive layer, in line with DGT theoretical predictions. DGT with both resin gels were tested in the laboratory for the effects of typical environmental factors on the DGT measurements. DGT performance was independent of the following: pH in the range of 4.7-8.2; dissolved organic matter concentrations <20 mg L^-1; and ionic strength from 0.01 to 0.25 M, although it was slightly affected at 0.5 M in some cases. This confirms DGT as a sampler suitable for controlled studies of environmental processes affecting pesticides. Field applications of DGT to measure pesticides in situ in waters and controlled laboratory measurements on five different soils (prepared at fixed soil/water ratios) demonstrated DGT is a suitable tool for environmental monitoring in waters and for investigating chemical processes in soils.