Tuning the Structure, Conductivity, and Wettability of Laser-Induced Graphene for Multiplexed Open Microfluidic Environmental Biosensing and Energy Storage Devices

Robust, stretchable bioelectronic interfaces for cardiac pacing enabled by interfacial transfer of laser-induced graphene via water-response, nonswellable PVA gels

Implantable cardiac pacemakers are crucial therapeutic tools for managing various cardiac conditions. For effective pacing, electrodes should exhibit flexibility, deformability, biocompatibility, and high conductivity/capacitance. Laser-induced graphene (LIG) shows promise due to its exceptional electrical and electrochemical properties. However, the fragility of LIG and the non-stretchability of polyimide substrates pose challenges when interfacing with the beating heart. Here, we present a simple method for fabricating robust, flexible, and stretchable bioelectronic interfaces by transferring LIG via water-responsive, nonswellable polyvinyl alcohol (PVA) gels. PVA solution penetrates the porous structure of LIG and solidifies into PVA xerogel as the solvent evaporates. The robust PVA xerogel enables the smooth transfer of LIG and prevents stretching of the LIG network during this process, which helps maintain its conductivity. When hydrated, the xerogel becomes a stable, nonswellable hydrogel. This gives the LIG-PVA hydrogel (LIG-PVA-H) composites with excellent conductivity (119.7 ± 4.3Ω sq-1), high stretchability (up to 420%), reliability (cyclic stretch under 15% strain, with ∼ 1-time resistance increase), and good stability in phosphate buffered saline. The LIG-PVA-H composites were used as biointerfaces for electrocardiogram signal recording and electrical pacing on rat hearts ex vivo and in vivo, using commercial setups and a custom-built implantable wireless device. This work expands the application of LIG in bioelectronic interfaces and facilitates the development of electrotherapy for cardiac diseases.

High-Performance Sensing Platform Based on Morphology/Lattice Collaborative Control of Femtosecond-Laser-Induced MXene-Composited Graphene

Flexible sensors based on laser-induced graphene (LIG) are widely used in wearable personal devices, with the morphology and lattice arrangement of LIG the key factors affecting their performance in various applications. In this study, femtosecond-laser-induced MXene-composited graphene (LIMG) is used to improve the electrical conductivity of graphene by incorporating MXene, a 2D material with a high concentration of free electrons, into the LIG structure. By combining pump-probe detection, laser-induced breakdown spectroscopy (LIBS), and density functional theory (DFT) calculations, the morphogenesis and lattice structuring principles of LIMG is explored, with the results indicating that MXene materials are successfully embedded in the graphene lattice, altering both their morphology and electrical properties. The structural sparsity and electrical conductivity of LIMG composites (up to 3187 S m-1) are significantly enhanced compared to those of LIG. Based on these findings, LIMG has been used in wearable electronics. LIMG electrodes are used to detect uric acid, with a minimum detection limit of 2.48 µM. Additionally, LIMG-based pressure and bending sensors have been successfully used to monitor human limb movement and pulse. The direct in situ femtosecond laser patterning synthesis of LIMG has significant implications for developing flexible wearable electronic sensors.

Ultrafast and Reversible Superwettability Switching of 3D Graphene Foams via Solvent-Exclusive Plasma Treatments

For highly active electron transfer and ion diffusion, controlling the surface wettability of electrically and thermally conductive 3D graphene foams (3D GFs) is required. Here, we present ultrasimple and rapid superwettability switching of 3D GFs in a reversible and reproducible manner, mediated by solvent-exclusive microwave arcs. As the 3D GFs are prepared with vapors of nonpolar acetone or polar water exclusively, short microwave radiation (≤10 s) leads to plasma hotspot-mediated production of methyl and hydroxyl radicals, respectively. Upon immediate radical chemisorption, the 3D surfaces become either superhydrophobic (water contact angle = ∼170°) or superhydrophilic (∼0°), and interestingly, the wettability transition can be repeated many times due to the facile exchange between previously chemisorbed and newly introduced radicals via the formation of methanol-like intermediates. When 3D GFs of different surficial polarities are incorporated into electric double-layer capacitors with nonpolar ionic liquids or polar aqueous electrolytes, the polarity matching between graphene surfaces and electrolytes results in ≥548.0 times higher capacitance compared to its mismatching at ≥0.5 A g-1, demonstrating the significance of wettability-controlled 3D GFs.

Carbon Micro/Nano Machining toward Miniaturized Device: Structural Engineering, Large-Scale Fabrication, and Performance Optimization

With the rapid development of micro/nano machining, there is an elevated demand for high-performance microdevices with high reliability and low cost. Due to their outstanding electrochemical, optical, electrical, and mechanical performance, carbon materials are extensively utilized in constructing microdevices for energy storage, sensing, and optoelectronics. Carbon micro/nano machining is fundamental in carbon-based intelligent microelectronics, multifunctional integrated microsystems, high-reliability portable/wearable consumer electronics, and portable medical diagnostic systems. Despite numerous reviews on carbon materials, a comprehensive overview is lacking that systematically encapsulates the development of high-performance microdevices based on carbon micro/nano structures, from structural design to manufacturing strategies and specific applications. This review focuses on the latest progress in carbon micro/nano machining toward miniaturized device, including structural engineering, large-scale fabrication, and performance optimization. Especially, the review targets an in-depth evaluation of carbon-based micro energy storage devices, microsensors, microactuators, miniaturized photoresponsive and electromagnetic interference shielding devices. Moreover, it highlights the challenges and opportunities in the large-scale manufacturing of carbon-based microdevices, aiming to spark further exciting research directions and application prospectives.

Biomimetic laser-induced graphene fern leaf and enzymatic biosensor for pesticide spray collection and monitoring

Monitoring of pesticide concentration distribution across farm fields is crucial to ensure precise and efficient application while preventing overuse or untreated areas. Inspired by nature's wettability patterns, we developed a biomimetic fern leaf pesticide collection patch using laser-induced graphene (LIG) alongside an external electrochemical LIG biosensor. This "collect-and-sense" system allows for rapid pesticide spray monitoring in the farm field. The LIG is synthesized and patterned on polyimide through a high-throughput gantry-based CO2 laser process, making it amenable to scalable manufacturing. The resulting LIG-based leaf exhibits a remarkable water collection capacity, harvesting spray mist/fog at a rate approximately 11 times greater than a natural ostrich fern leaf when the collection is normalized to surface area. The developed three-electrode LIG pesticide biosensor, featuring a working electrode functionalized with electrodeposited platinum nanoparticles (PtNPs) and the enzyme glycine oxidase, displayed a linear range of 10-260 μM, a detection limit of 1.15 μM, and a sensitivity of 5.64 nA μM-1 for the widely used herbicide glyphosate. Also, a portable potentiostat with a user-friendly interface was developed for remote operation, achieving an accuracy of up to 97%, when compared to a standard commercial benchtop potentiostat. The LIG "collect-and-sense" system can consistently collect and monitor glyphosate spray after 24-48 hours of spraying, a time that corresponds to the restricted-entry interval required to enter most farm fields after pesticide spraying. Hence, this innovative "collect-and-sense" system not only advances precision agriculture by enabling monitoring and mapping of pesticide distribution but also holds the potential to significantly reduce environmental impact, enhance crop management practices, and contribute to the sustainable and efficient use of agrochemicals in modern agriculture.

Fabrication of a 96-electrode array using carbon dioxide laser ablation

The 96 laser-induced multigraphene electrode (96L-MGE) integrated microwell plate (96 L-MGE-MP) is described. Each cell includes separate working, auxiliary, and reference electrodes, and the array sits on a poly-methyl methacrylate (PMMA) well. The 96 electrochemical cells were fabricated by laser ablation of polyimide adhesive tape, which created laser-induced graphene electrodes (L-GE). The microwell was produced using laser ablation of the PMMA sheet as well. The morphology and electrochemical characterization of L-GE were controlled by tuning the laser processing. L-GE fabricated at laser power-laser speed ratios of 0.008-0.02 W s mm-1displayed good electrochemical behaviors. Under the optimal condition of L-GE fabrication, the measured L-GE surface roughness was 475.47 nm. The 96 L-MGE can be fabricated in 24.2 min and is compatible with various analytes. 10 benchmark redox compounds were shown as electrocatalytic examples. The performance of each analyte was investigated by voltammetry. As proof of concept, 96 L-MGE-MP was connected to a 96× connector for multichannel detection. The RSD of the 96 L-MGE-MPwas below 5.3%, which demonstrated good fabrication reproducibility.

Batch-to-Batch Variation in Laser-Inscribed Graphene (LIG) Electrodes for Electrochemical Sensing

Laser-inscribed graphene (LIG) is an emerging material for micro-electronic applications and is being used to develop supercapacitors, soft actuators, triboelectric generators, and sensors. The fabrication technique is simple, yet the batch-to-batch variation of LIG quality is not well documented in the literature. In this study, we conduct experiments to characterize batch-to-batch variation in the manufacturing of LIG electrodes for applications in electrochemical sensing. Numerous batches of 36 LIG electrodes were synthesized using a CO2 laser system on polyimide film. The LIG material was characterized using goniometry, stereomicroscopy, open circuit potentiometry, and cyclic voltammetry. Hydrophobicity and electrochemical screening (cyclic voltammetry) indicate that LIG electrode batch-to-batch variation is less than 5% when using a commercial reference and counter electrode. Metallization of LIG led to a significant increase in peak current and specific capacitance (area between anodic/cathodic curve). However, batch-to-batch variation increased to approximately 30%. Two different platinum electrodeposition techniques were studied, including galvanostatic and frequency-modulated electrodeposition. The study shows that formation of metallized LIG electrodes with high specific capacitance and peak current may come at the expense of high batch variability. This design tradeoff has not been discussed in the literature and is an important consideration if scaling sensor designs for mass use is desired. This study provides important insight into the variation of LIG material properties for scalable development of LIG sensors. Additional studies are needed to understand the underlying mechanism(s) of this variability so that strategies to improve the repeatability may be developed for improving quality control. The dataset from this study is available via an open access repository.

Microfluidic sensors for the detection of emerging contaminants in water: A review

In recent years, numerous emerging contaminants have been identified in surface water, groundwater, and drinking water. Developing novel sensing methods for detecting diverse emerging pollutants in water is urgently needed, as even at low concentrations, these pollutants can pose a serious threat to human health and environmental safety. Traditional testing methods are based on laboratory equipment, which is highly sensitive but complex to operate, costly, and not suitable for on-site monitoring. Microfluidic sensors offer several benefits, including rapid evaluation, minimal sample usage, accurate liquid manipulation, compact size, automation, and in-situ detection capabilities. They provide promising and efficient analytical tools for high-performance sensing platforms in monitoring emerging contaminants in water. In this paper, recent research advances in microfluidic sensors for the detection of emerging contaminants in water are reviewed. Initially, a concise overview is provided about the various substrate materials, corresponding microfabrication techniques, different driving forces, and commonly used detection techniques for microfluidic devices. Subsequently, a comprehensive analysis is conducted on microfluidic detection methods for endocrine-disrupting chemicals, pharmaceuticals and personal care products, microplastics, and perfluorinated compounds. Finally, the prospects and future challenges of microfluidic sensors in this field are discussed.

Moisture-enabled self-charging and voltage stabilizing supercapacitor

Supercapacitor is highly demanded in emerging portable electronics, however, which faces frequent charging and inevitable rapid self-discharging of huge inconvenient. Here, we present a flexible moisture-powered supercapacitor (mp-SC) that capable of spontaneously moisture-enabled self-charging and persistently voltage stabilizing. Based on the synergy effect of moisture-induced ions diffusion of inner polyelectrolyte-based moist-electric generator and charges storage ability of inner graphene electrochemical capacitor, this mp-SC demonstrates the self-charged high areal capacitance of 138.3 mF cm-2 and ~96.6% voltage maintenance for 120 h. In addition, a large-scale flexible device of 72 mp-SC units connected in series achieves a self-charged 60 V voltage in air, efficiently powering various commercial electronics in practical applications. This work will provide insight into the design self-powered and ultra-long term stable supercapacitors and other energy storage devices.

Laser-Printed Photoanode: Femtosecond Laser-Induced Crystalline Phase Transformation of WO3 Nanorods for Space-Efficient and Flexible Thin-Film Solar Water-Splitting Cells

Despite its potential for clean hydrogen harvesting, photoelectrochemical (PEC) water-splitting cells face challenges in commercialization, particularly related its harvesting performance and productivity at an industrial scale. Herein, a facile fabrication method of flexible thin-film photoanode for PEC water-splitting to overcome these limitations, based on laser processing technologies, is proposed. Laser-induced graphene, a carbon structure produced through direct laser writing carbonization (DLWC), plays a dual role: a flexible and stable current collector and a substrate for the hydrothermal synthesis of tungsten trioxide (WO3) nanorods (NRs). To facilitate water-splitting, a femtosecond-pulsed laser (fs laser) is focused on the WO3 NRs, converting their crystalline phase from pristine orthorhombic to monoclinic structure without thermal damage. With NiFe layered double hydroxide (LDH) catalyst, the flexible thin-film photoanode exhibits good PEC performance (1.46 mA cm-2 at 1.23 VRHE) and retains ≈90% of its performance after 3000 bending cycles. With its excellent mechanical properties, the flexible photoanode can be operated in various shapes with different curvatures, enabling space-efficient PEC water-splitting by loading larger photoanode within a given space. This study is expected to contribute to the advancement of large-scale solar water-splitting cells, introducing a new approach to enhance H2/O2 production and expand its application range.

Laser-induced graphene trending in biosensors: understanding electrode shelf-life of this highly porous material

Laser-induced graphene (LIG) has received much attention in recent years as a possible transducer material for electroanalytical sensors. Its simplicity of fabrication and good electrochemical performance are typically highlighted. However, we found that unmodified and untreated LIG electrodes had a limited shelf-life for certain electroanalytical applications, likely due to the adsorption of adventitious hydrocarbons from the storage environment. Electrode responses did not change immediately after exposure to ambient conditions but over longer periods of time, probably due to the immense specific surface area of the LIG material. LIG shelf-life is seldomly discussed prominently in the literature, yet overall trends for solutions to this challenge can be identified. Such findings from the literature regarding the long-term storage stability of LIG electrodes, pure and modified, are discussed here along with explanations for likely protective mechanisms. Specifically, applying a protective coating on LIG electrodes after manufacture is possibly the easiest method to preserve electrode functionality and should be identified as a trend for well-performing LIG electrodes in the future. Furthermore, suggested influences of the accompanying LIG microstructure/morphology on electrode characteristics are evaluated.

Multifaceted experiments and photothermal simulations based analysis of laser induced graphene and its fibers

The interaction of CO2 laser with polyimide results in the formation of laser-induced graphene (LIG) and other morphological transitions based on laser parameters, such as Laser-induced fibers (LIF) on the surface. However, a fundamental investigation of LIF, its properties and potential have not been explored until now. We aim therefore to provide novel insights into the LIF by characterization of its structural, electrical, electrochemical, and mechanical properties. Four different morphologies were identified depending on the laser parameters and the temperature required for their formation were quantified by FEM model. Minimum temperatures of 1800 K were required to form LIG and around 2600 to 5000 K to form LIF. High heterogeneity of the LIF along thickness due to temperature gradients, and the existence of sheet structures underneath the fibers were identified. Due to the loosely bound nature of fibers, LIF dispersion was prepared by ultrasonication to functionalize the carbon electrode for electrochemical characterization. The modification with LIF on the electrodes enhanced the electrochemical response of the electrode towards standard redox couple which confirmed the conductive nature of the fibers. This work provides a solid basis for the versatile tuning of the behavior and properties of LIF for potential applications.

Hydrophobic Surface Array Structure Based on Laser-Induced Graphene for Deicing and Anti-Icing Applications

The exceptional performance of graphene has driven the advancement of its preparation techniques and applications. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by the LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure was subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy and energy-dispersive X-ray spectroscopy. The periodic linear array structure was observed by scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that high-quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100 °C and 240 °C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and that the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

Practical Considerations for Laser-Induced Graphene Pressure Sensors Used in Marine Applications

Small, low-power, and inexpensive marine depth sensors are of interest for a myriad of applications from maritime security to environmental monitoring. Recently, laser-induced graphene (LIG) piezoresistive pressure sensors have been proposed given their rapid fabrication and large dynamic range. In this work, the practicality of LIG integration into fieldable deep ocean (1 km) depth sensors in bulk is explored. Initially, a design of experiments (DOEs) approach evaluated laser engraver fabrication parameters such as line length, line width, laser speed, and laser power on resultant resistances of LIG traces. Next, uniaxial compression and thermal testing at relevant ocean pressures up to 10.3 MPa and temperatures between 0 and 25 °C evaluated the piezoresistive response of replicate sensors and determined the individual characterization of each, which is necessary. Additionally, bare LIG sensors showed larger resistance changes with temperature (ΔR ≈ 30 kΩ) than pressure (ΔR ≈ 1-15 kΩ), indicating that conformal coatings are required to both thermally insulate and electrically isolate traces from surrounding seawater. Sensors encapsulated with two dip-coated layers of 5 wt% polydimethylsiloxane (PDMS) silicone and submerged in water baths from 0 to 25 °C showed significant thermal dampening (ΔR ≈ 0.3 kΩ), indicating a path forward for the continued development of LIG/PDMS composite structures. This work presents both the promises and limitations of LIG piezoresistive depth sensors and recommends further research to validate this platform for global deployment.

Three dimensional high-performance micro-supercapacitors with switchable high power density and high energy density

In the field of microscale energy storage, the fabrication of micro-supercapacitors (MSCs) with high power density and high energy density has always been a focus of research. In this work, laser-induced porous graphene and chemically deposited manganese dioxide nanoparticles are used as electrode materials, and a switchable MSC with two energy storage principles is obtained by designing symmetric interdigitated and square electrode structures. The aim is to overcome the preparation challenge of supercapacitors with high energy density and high power density by switching between two modes. In this MSC, the energy density of the high energy density mode (5.89 μW h cm-2) is 3.36 times that of the high power density mode (1.75 μW h cm-2), while the power density of the high power density mode (43.06 μW cm-2) is 1.44 times that of the high energy density mode (29.96 μW cm-2). In addition, under the drive of five serially connected MSCs, 27 LED lights can be continuously lit for 5 minutes. Therefore, this work provides a facile and novel method for the development of MSCs with high power density and high energy density, suggesting a great practical application value in the development of MSCs.

Effects of additives on the performance of a laser-induced graphene sensor modified with ZrO2 nanoparticles for OP detection

In this study, a simple and portable electrochemical sensor based on laser-induced graphene (LIG) has been developed to systematically investigate the feasibility of LIG as an electrode to detect organophosphorus pesticides (OPs). It proves that the LIG-based electrode has a relatively high electrochemically active surface area (ECSA) and heterogeneous electron transfer (HET) of 0.100 cm2 and 0.000825 cm s-1, respectively. In addition, zirconium dioxide nanoparticles (ZrO2 NPs) have been modified on the electrode with three different binders, β-cyclodextrin (β-CD), chitosan (CS) and Nafion, to improve the adsorption capacity of the electrode toward OPs, and the effect of the binders on the performance of the as-fabricated sensor has been investigated in detail. The results show that β-CD increases not only the electrochemically active surface area of the electrode but also the redox peak current of methyl parathion (MP). To evaluate the sensitivity of the sensor, differential pulse voltammetry (DPV) curves have been tested in solutions containing different concentrations of MP using ZrO2-β-CD/LIG as an electrode, which shows a detection range of 5-200 ng ml-1 and a detection limit of 0.89 ng ml-1. In summary, the LIG-based sensor has a low detection limit, high sensitivity and good interference resistance, and thus has tremendous potential for the detection of pesticides in the environment.

Different Roles of Surface Chemistry and Roughness of Laser-Induced Graphene: Implications for Tunable Wettability

The control of surface wettability is a technological key aspect and usually poses considerable challenges connected to high cost, nanostructure, and durability, especially when aiming at surface patterning with high and extreme wettability contrast. This work shows a simple and scalable approach by using laser-induced graphene (LIG) and a locally inert atmosphere to continuously tune the wettability of a polyimide/LIG surface from hydrophilic to superhydrophobic (Φ ∼ 160°). This is related to the reduced amount of oxygen on the LIG surface, influenced by the local atmosphere. Furthermore, the influence of the roughness pattern of LIG on the wettability is investigated. Both approaches are combined, and the influence of surface chemistry and roughness is discussed. Measurements of the roll-off angle show that LIG scribed in an inert atmosphere with a low roughness has the highest droplet mobility with a roll-off angle of ΦRO = (1.7 ± 0.3)°. The superhydrophobic properties of the samples were maintained for over a year and showed no degradation after multiple uses. Applications of surfaces with extreme wettability contrast in millifluidics and fog basking are demonstrated. Overall, the proposed processing allows for the continuous tuning and patterning of the surface properties of LIG in a very accessible fashion useful for "lab-on-chip" applications.

Wearable Flexible Perspiration Biosensors Using Laser-Induced Graphene and Polymeric Tape Microfluidics

Wearable biosensors promise real-time measurements of chemicals in human sweat, with the potential for dramatic improvements in medical diagnostics and athletic performance through continuous metabolite and electrolyte monitoring. However, sweat sensing is still in its infancy, and questions remain about whether sweat can be used for medical purposes. Wearable sensors are focused on proof-of-concept designs that are not scalable for multisubject trials, which could elucidate the utility of sweat sensing for health monitoring. Moreover, many wearable sensors do not include the microfluidics necessary to protect and channel consistent and clean sweat volumes to the sensor surface or are not designed to be disposable to prevent sensor biofouling and inaccuracies due to repeated use. Hence, there is a need to produce low-cost and single-use wearable sensors with integrated microfluidics to ensure reliable sweat sensing. Herein, we demonstrate the convergence of laser-induced graphene (LIG) based sensors with soft tape polymeric microfluidics to quantify both sweat metabolites (glucose and lactate) and electrolytes (sodium) for potential hydration and fatigue monitoring. Distinct LIG-electrodes were functionalized with glucose oxidase and lactate oxidase for selective sensing of glucose and lactate across physiological ranges found in sweat with sensitivities of 26.2 and 2.47 × 10-3 μA mM-1 cm-2, detection limits of 8 and 220 μM, and linear response ranges of 0-1 mM and 0-32 mM, respectively. LIG-electrodes functionalized with a sodium-ion-selective membrane displayed Nernstian sensitivity of 58.8 mV decade-1 and a linear response over the physiological range in sweat (10-100 mM). The sensors were tested in a simulated sweating skin microfluidic system and on-body during cycling tests in a multisubject trial. Results demonstrate the utility of LIG integrated with microfluidics for real-time, continuous measurements of biological analytes in sweat and help pave the way for the development of personalized wearable diagnostic tools.

A Connected World: System-Level Support Through Biosensors

The goal of protecting the health of future generations is a blueprint for future biosensor design. Systems-level decision support requires that biosensors provide meaningful service to society. In this review, we summarize recent developments in cyber physical systems and biosensors connected with decision support. We identify key processes and practices that may guide the establishment of connections between user needs and biosensor engineering using an informatics approach. We call for data science and decision science to be formally connected with sensor science for understanding system complexity and realizing the ambition of biosensors-as-a-service. This review calls for a focus on quality of service early in the design process as a means to improve the meaningful value of a given biosensor. We close by noting that technology development, including biosensors and decision support systems, is a cautionary tale. The economics of scale govern the success, or failure, of any biosensor system.

Ion-selective electrodes based on laser-induced graphene as an alternative method for nitrite monitoring

Nitrite is an important food additive for cured meats; however, high nitrite levels pose adverse health effects to humans. Hence, monitoring nitrite concentration is critical to comply with limits imposed by regulatory agencies. Laser-induced graphene (LIG) has proven to be a scalable manufacturing alternative to produce high-performance electrochemical transducers for sensors. Herein, we expand upon initial LIG studies by fabricating hydrophilic and hydrophobic LIG that are subsequently converted into ion-selective sensors to monitor nitrite in food samples with comparable performance to the standard photometric method (Griess method). The hydrophobic LIG resulted in an ion-selective electrode with improved potential stability due partly to a decrease in the water layer between the electrode and the nitrite poly(vinyl) chloride-based ion-selective membrane. These resultant nitrite ion-selective sensors displayed Nernstian response behavior with a sensitivity of 59.5 mV dec-1, a detection limit of 0.3 ± 0.1 mg L-1 (mean ± standard deviation), and a broad linear sensing range from 10-5 to 10-1 M, which was significantly larger than currently published nitrite methods. Nitrite levels were determined directly in food extract samples of sausage, ham, and bacon for 5 min. These sensor metrics are significant as regulatory agencies limit nitrite levels up to 200 mg L-1 in finished products to reduce the potential formation of nitrosamine (carcinogenic compound). These results demonstrate the versatility of LIG as a platform for ion-selective-LIG sensors and simple, efficient, and scalable electrochemical sensing in general while demonstrating a promising alternative to monitor nitrite levels in food products ensuring regulatory compliance.

Laser induced graphanized microfluidic devices

With the advent of cyber-physical system-based automation and intelligence, the development of flexible and wearable devices has dramatically enhanced. Evidently, this has led to the thrust to realize standalone and sufficiently-self-powered miniaturized devices for a variety of sensing and monitoring applications. To this end, a range of aspects needs to be carefully and synergistically optimized. These include the choice of material, micro-reservoir to suitably place the analytes, integrable electrodes, detection mechanism, microprocessor/microcontroller architecture, signal-processing, software, etc. In this context, several researchers are working toward developing novel flexible devices having a micro-reservoir, both in flow-through and stationary phases, integrated with graphanized zones created by simple benchtop lasers. Various substrates, like different kinds of cloths, papers, and polymers, have been harnessed to develop laser-ablated graphene regions along with a micro-reservoir to aptly place various analytes to be sensed/monitored. Likewise, similar substrates have been utilized for energy harvesting by fuel cell or solar routes and supercapacitor-based energy storage. Overall, realization of a prototype is envisioned by integrating various sub-systems, including sensory, energy harvesting, energy storage, and IoT sub-systems, on a single mini-platform. In this work, the diversified work toward developing such prototypes will be showcased and current and future commercialization potential will be projected.

Patterning Wettability for Open-Surface Fluidic Manipulation: Fundamentals and Applications

Effective manipulation of liquids on open surfaces without external energy input is indispensable for the advancement of point-of-care diagnostic devices. Open-surface microfluidics has the potential to benefit health care, especially in the developing world. This review highlights the prospects for harnessing capillary forces on surface-microfluidic platforms, chiefly by inducing smooth gradients or sharp steps of wettability on substrates, to elicit passive liquid transport and higher-order fluidic manipulations without off-the-chip energy sources. A broad spectrum of the recent progress in the emerging field of passive surface microfluidics is highlighted, and its promise for developing facile, low-cost, easy-to-operate microfluidic devices is discussed in light of recent applications, not only in the domain of biomedical microfluidics but also in the general areas of energy and water conservation.

A Self-Powered Wearable Sensor for Continuous Wireless Sweat Monitoring

Wireless wearable sweat analysis devices can monitor biomarkers at the molecular level continuously and in situ, which is highly desired for personalized health care. The miniaturization, integration, and wireless operation of sweat sensors improve the comfort and convenience while also bringing forward new challenges for power supply technology. Herein, a wireless self-powered wearable sweat analysis system (SWSAS) is designed that effectively converts the mechanical energy of human motion into electricity through hybrid nanogenerator modules (HNGMs). The HNGM shows stable output characteristics at low frequency with a current of 15 mA and a voltage of 60 V. Through real-time on-body sweat analysis powered by HNGM, the SWSAS is demonstrated to selectively monitor biomarkers (Na⁺ and K⁺ ) in sweat and wirelessly transmit the sensing data to the user interface via Bluetooth.

Miniaturized sensor for electroanalytical and electrochemiluminescent detection of pathogens enabled through laser-induced graphene electrodes embedded in microfluidic channels

High performance, laser-induced graphene (LIG) electrodes were integrated into adhesive tape-based microfluidic channels to realize both electrochemical (EC) and electrochemiluminescent (ECL) detection approaches. This provides strategies for low limits of detection, simple hardware requirements and inexpensive fabrication, which are characteristics required for assays in the competitive point-of-care (POC) sensor field. Here, electrode design and microchannel dimensions were studied and a DNA hybridization assay with liposomes for signal amplification was developed for the specific detection of DNA derived from Cryptosporidium parvum as the model analyte. Liposomes entrapped either Ru(bpy)₃²⁺ or K₄[Fe(CN)₆] generating ECL- and EC-signal amplification, respectively. This new microchip provided all desirable analytical figures of merit needed for POC applications. Specifically, a desirable one-step assay was designed which provided a limit of detection of 3 pmol L^-1 for the ECL and 47 pmol L^-1 for the EC approach and furthermore enabled highly specific detection considering that at room temperature in this simple setup a single nucleotide polymorphism resulted in a signal decrease of 58%, whereas a decrease of > 98% was observed for non-matching sequences present in 10-fold excess. Direct detection in various matrices ranging from drinking water to soil extracts was also achieved. It is concluded that the simple and inexpensive fabrication in combination with signal amplification strategies makes these concepts relevant for on-site pathogen detection in resource-limited environments.

Engineering Interlaced Architecture of Pristine Graphene Anchored with 2-Amino-8-Naphthol 6-Sulfonic Acids for Printed Hybrid Micro-Supercapacitors with High Electrochemical Capability

All-printed flexible micro-supercapacitors (MSCs) based on two-dimensional (2D) nanomaterials with in-plane interdigital configurations are regarded as promising miniaturized power source units, but they chronically suffer from self-aggregation and inadequate matching of electrode materials, thus resulting in inefficient electrolyte ions intercalation. Herein, an innovative multicomponent interlaced architecture essentially consisting of 2-amino-8-naphthol 6-sulfonic acid (ANS)-anchored pristine graphene and highly conductive multiwalled carbon nanotubes is reported. The assembled and optimized Gr@ANS electrodes offer sufficient absorption/desorption and redox-active sites, delivering a high areal capacitance of 33.7 mF/cm² for screen-printed MSCs. Particularly, the well-modified Gr@ANS/CNTs-interlaced complex structure effectively prevents the usual restacking of the delaminated Gr@ANS nanosheets and maximizes ion accessibility in electrodes. Ascribed to the optimized electron-transferring kinetics, the achieved Gr@ANS/CNTs MSCs exhibit excellent capacitance (40.2 mF/cm² and 18.8 F/cm³), simultaneously significantly increasing the rate capability of Gr@ANS MSCs (from 3.9 to 60.0%). Arising from the multicomponent synergism, the all-solid-state MSCs exhibit outstanding bending stability and cycling performance (73.8% after 10 000 charge/discharge cycles). The new charge reservoir engineering evidenced in graphene-based micro-supercapacitors would serve as a stepping stone toward the scalable manufacture of hybrid energy storage micro-devices.

Enzymatic Laser-Induced Graphene Biosensor for Electrochemical Sensing of the Herbicide Glyphosate

Glyphosate is a globally applied herbicide yet it has been relatively undetectable in-field samples outside of gold-standard techniques. Its presumed nontoxicity toward humans has been contested by the International Agency for Research on Cancer, while it has been detected in farmers' urine, surface waters and crop residues. Rapid, on-site detection of glyphosate is hindered by lack of field-deployable and easy-to-use sensors that circumvent sample transportation to limited laboratories that possess the equipment needed for detection. Herein, the flavoenzyme, glycine oxidase, immobilized on platinum-decorated laser-induced graphene (LIG) is used for selective detection of glyphosate as it is a substrate for GlyOx. The LIG platform provides a scaffold for enzyme attachment while maintaining the electronic and surface properties of graphene. The sensor exhibits a linear range of 10-260 µ m, detection limit of 3.03 µ m, and sensitivity of 0.991 nA µ m ^-1. The sensor shows minimal interference from the commonly used herbicides and insecticides: atrazine, 2,4-dichlorophenoxyacetic acid, dicamba, parathion-methyl, paraoxon-methyl, malathion, chlorpyrifos, thiamethoxam, clothianidin, and imidacloprid. Sensor function is further tested in complex river water and crop residue fluids, which validate this platform as a scalable, direct-write, and selective method of glyphosate detection for herbicide mapping and food analysis.

Surface Wettability for Skin-Interfaced Sensors and Devices

The practical applications of skin-interfaced sensors and devices in daily life hinge on the rational design of surface wettability to maintain device integrity and achieve improved sensing performance under complex hydrated conditions. Various bio-inspired strategies have been implemented to engineer desired surface wettability for varying hydrated conditions. Although the bodily fluids can negatively affect the device performance, they also provide a rich reservoir of health-relevant information and sustained energy for next-generation stretchable self-powered devices. As a result, the design and manipulation of the surface wettability are critical to effectively control the liquid behavior on the device surface for enhanced performance. The sensors and devices with engineered surface wettability can collect and analyze health biomarkers while being minimally affected by bodily fluids or ambient humid environments. The energy harvesters also benefit from surface wettability design to achieve enhanced performance for powering on-body electronics. In this review, we first summarize the commonly used approaches to tune the surface wettability for target applications toward stretchable self-powered devices. By considering the existing challenges, we also discuss the opportunities as a small fraction of potential future developments, which can lead to a new class of skin-interfaced devices for use in digital health and personalized medicine.

Electrooculography and Tactile Perception Collaborative Interface for 3D Human-Machine Interaction

The human-machine interface (HMI) previously relied on a single perception interface that cannot realize three-dimensional (3D) interaction and convenient and accurate interaction in multiple scenes. Here, we propose a collaborative interface including electrooculography (EOG) and tactile perception for fast and accurate 3D human-machine interaction. The EOG signals are mainly used for fast, convenient, and contactless 2D (XY-axis) interaction, and the tactile sensing interface is mainly utilized for complex 2D movement control and Z-axis control in the 3D interaction. The honeycomb graphene electrodes for the EOG signal acquisition and tactile sensing array are prepared by a laser-induced process. Two pairs of ultrathin and breathable honeycomb graphene electrodes are attached around the eyes for monitoring nine different eye movements. A machine learning algorithm is designed to train and classify the nine different eye movements with an average prediction accuracy of 92.6%. Furthermore, an ultrathin (90 μm), stretchable (∼1000%), and flexible tactile sensing interface assembled by a pair of 4 × 4 planar electrode arrays is attached to the arm for 2D movement control and Z-axis interaction, which can realize single-point, multipoint and sliding touch functions. Consequently, the tactile sensing interface can achieve eight directions control and even more complex movement trajectory control. Meanwhile, the flexible and ultrathin tactile sensor exhibits an ultrahigh sensitivity of 1.428 kPa^-1 in the pressure range 0-300 Pa with long-term response stability and repeatability. Therefore, the collaboration between EOG and the tactile perception interface will play an important role in rapid and accurate 3D human-machine interaction.

Development of a Biosensor Based on Angiotensin-Converting Enzyme II for Severe Acute Respiratory Syndrome Coronavirus 2 Detection in Human Saliva

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is the novel coronavirus responsible for COVID-19. Infection in humans requires angiotensin-converting enzyme II (hACE2) as the point of entry for SARS-CoV-2. PCR testing is generally definitive but expensive, although it is highly sensitive and accurate. Biosensor-based monitoring could be a low-cost, accurate, and non-invasive approach to improve testing capacity. We develop a capacitive hACE2 biosensor for intact SARS-CoV-2 detection in saliva. Laser-induced graphene (LIG) electrodes were modified with platinum nanoparticles. The quality control of LIG electrodes was performed using cyclic voltammetry. Truncated hACE2 was used as a biorecognition element and attached to the electrode surface by streptavidin-biotin coupling. Biolayer interferometry was used for qualitative interaction screening of hACE2 with UV-attenuated virions. Electrochemical impedance spectroscopy (EIS) was used for signal transduction. Truncated hACE2 binds wild-type SARS-CoV-2 and its variants with greater avidity than human coronavirus (common cold virus). The limit of detection (LoD) is estimated to be 2,960 copies/ml. The detection process usually takes less than 30 min. The strength of these features makes the hACE2 biosensor a potentially low-cost approach for screening SARS-CoV-2 in non-clinical settings with high demand for rapid testing (for example, schools and airports).