Breathable Vapor Toxicant Barriers Based on Multilayer Graphene Oxide

2D materials towards energy conversion processes in nanofluidics

Hierarchically assembled 2D material membranes are extremely promising platforms for energy conversion processes in nanofluidics. In this perspective, we discuss recent advances in the production of smart 2D material membranes that come close to mimicking biological energy conversion processes and how these efforts translate into the design of water purification systems, artificial photosynthesis, and solar energy conversion devices. As we depict here, 2D material membranes synergistically modulate the intrinsic active sites (nanopores), electron transport, mass transfer, and mechanical and chemical stability aiming at cost-effective and highly efficient smart membranes.

Chemodiversity of soil organic matters determines biodegradation of polychlorinated biphenyls by a graphene oxide-assisted bacterial agent

A promising strategy for degrading persistent organic pollutants (POPs) in soil is amendment with nanomaterial-assisted functional bacteria. However, the influence of soil organic matter chemodiversity on the performance of nanomaterial-assisted bacterial agents remains unclear. Herein, different types of soil (Mollisol soil, MS; Ultisol soil, US; and Inceptisol soil, IS) were inoculated with a graphene oxide (GO)-assisted bacterial agent (Bradyrhizobium diazoefficiens USDA 110, B. diazoefficiens USDA 110) to investigate the association between soil organic matter chemodiversity and stimulation of polychlorinated biphenyl (PCB) degradation. Results indicated that the high-aromatic solid organic matter (SOM) inhibited PCB bioavailability, and lignin-dominant dissolved organic matter (DOM) with high biotransformation potential was a favored substrate for all PCB degraders, which led to no stimulation of PCB degradation in MS. Differently, high-aliphatic SOM in US and IS promoted PCB bioavailability. The high/low biotransformation potential of multiple DOM components (e.g., lignin, condensed hydrocarbon, unsaturated hydrocarbon, etc.) in US/IS further resulted to the enhanced PCB degradation by B. diazoefficiens USDA 110 (up to 30.34%) /all PCB degraders (up to 17.65%), respectively. Overall, the category and biotransformation potential of DOM components and the aromaticity of SOM collaboratively determine the stimulation of GO-assisted bacterial agent on PCB degradation.

Therapeutic and diagnostic applications of nanoparticles in the management of COVID-19: a comprehensive overview

In December 2019, Coronavirus Disease 2019 (COVID-19) was reported in Wuhan, China. Comprehensive strategies for quick identification, prevention, control, and remedy of COVID-19 have been implemented until today. Advances in various nanoparticle-based technologies, including organic and inorganic nanoparticles, have created new perspectives in this field. These materials were extensively used to control COVID-19 because of their specific attribution to preparing antiviral face masks, various safety sensors, etc. In this review, the most current nanoparticle-based technologies, applications, and achievements against the coronavirus were summarized and highlighted. This paper also offers nanoparticle preventive, diagnostic, and treatment options to combat this pandemic.

Graphene materials: Armor against nosocomial infections and biofilm formation - A review

Graphene has revolutionized the field of energy and storage sectors. Out of the total number of nosocomial infections diagnosed all around the world, the majority of the cases (around 70%) are found to be due to the medical device or assistance utilized while treating the patient. Combating these diseases is vital as they cause a nuisance to the patients and medical practitioners. Coatings of graphene and its derivatives hold the key to the formation of special surfaces that can rupture microbial cells using their sharp edges, ultimately leading to nuclear and cellular fragmentation. Their incorporation as a whole or as a part in the hospital apparel and the medical device has aided medical practitioners to combat many nosocomial diseases. Graphene is found to be highly virulent with broad-spectrum antimicrobial activity against nosocomial strains and biofilm formation. Their alternate mode of action like trapping and charge transfer has also been discussed well in the present review. The various combinational forms of graphene with its conjugates as a suitable agent to combat nosocomial infections and a potential coating for newer challenges like COVID-19 infections has also been assessed in the current study. Efficiency of graphene sheets has been found to be around 89% with a reaction time as less as 3 h. Polymers with graphene seem to have a higher potency against biofilm formation. When combined with graphene oxide, silver nanoparticles provide 99% activity against nosocomial pathogens. In conclusion, this review would be a guiding light for scientists working with graphene-based coatings to unfold the potentials of this marvelous commodity to tackle the present and future pandemics to come.

Role of Nanomaterials in COVID-19 Prevention, Diagnostics, Therapeutics, and Vaccine Development

Facing the deadly pandemic caused by the SARS-CoV-2 virus all over the globe, it is crucial to devote efforts to fighting and preventing this infectious virus. Nanomaterials have gained much attention after the approval of lipid nanoparticle-based COVID-19 vaccines by the United States Food and Drug Administration (USFDA). In light of increasing demands for utilizing nanomaterials in the management of COVID-19, this comprehensive review focuses on the role of nanomaterials in the prevention, diagnostics, therapeutics, and vaccine development of COVID-19. First, we highlight the variety of nanomaterials usage in the prevention of COVID-19. We discuss the advantages of nanomaterials as well as their uses in the production of diagnostic tools and treatment methods. Finally, we review the role of nanomaterials in COVID-19 vaccine development. This review offers direction for creating products based on nanomaterials to combat COVID-19.

Graphene Oxide and Metal-Organic Framework-Based Breathable Barrier Membranes for Toxic Vapors

Garments protective against chemical warfare agents (CWAs) or accidently released toxic chemicals must block the transport of toxic gases/vapors for a substantial time and allow moisture transport for breathability. These demands are challenging: either the barriers block CWAs effectively but have poor breathability or barriers have excellent breathability but cannot block CWAs well. Existing protective garments employ large amounts of active carbon, making them quite heavy. Metal-organic framework (MOF)-based adsorbents are being investigated as sorbents for CWAs. Breathable laminate of graphene oxide (GO) flakes supported on a porous membrane reduces permeation rates of CWA simulants substantially. We developed a multilayered membrane-based flexible barrier: GO laminate-based membrane over a MOF nanocrystal-filled expanded polytetrafluorethylene (ePTFE) membrane having submicrometer pores. The GO laminate-based layer developed a steady breakthrough concentration level almost 2 orders of magnitude below the usual breakthrough level. This highly reduced level of CWA was blocked by the MOF nanocrystal-filled membrane substrate layer over a highly extended period. We demonstrated the blocking of CWAs, mustard (HD), soman (GD), a sarin simulant [dimethyl methyl phosphonate (DMMP)], and ammonia for an extended period while the moisture transmission rate was substantial. The times for complete blockage of ammonia, HD, GD, and DMMP were 2750 min, 1075 min, 176 min, and 7 days, respectively. This remarkable performance resulted from a very low steady-state penetrant permeation through GO-laminate membrane and substantial penetrant sorption by MOF nanocrystals; furthermore, both layers show high moisture vapor transmission.

Nano-silver functionalized spherical activated carbon with enhanced dipropyl sulfide adsorption capacity and antibacterial properties

Owing to the large dynamic adsorption performance and excellent mechanical strength, spherical activated carbon (SAC) has been widely applied in the field of biochemical protection. However, the adsorbed chemical warfare agent molecules might easily escape from the pores of SAC due to the impact of ambient temperature and humidity, resulting in secondary pollution. Herein, to improve the adsorption performance of SAC, an excessive impregnation method was used to fabricate nano-silver functionalized spherical activated carbon (Ag-SAC). The surface physicochemical structure of the obtained Ag-SAC was extensively studied, and dipropyl sulfide (DPS), a simulant of sulfur mustard (HD), was employed as the adsorbate to evaluate its adsorption capability. The effects of AgNO₃ impregnation concentration, reaction time, initial concentration and temperature on the adsorption performance, were investigated. The equilibrium adsorption capacity of Ag-SAC towards DPS increased by 13.41% compared with that of pristine SAC. Kinetic models, adsorption isotherm models, and adsorption thermodynamics were used to study the adsorption mechanism. The results revealed that the adsorption of DPS by Ag-SAC is a mixed synergistic process, which includes chemical adsorption and physical adsorption. Moreover, the Ag-SAC exhibited good antibacterial characteristics, with an antibacterial rate over 99.28% against Escherichia coli. We anticipate that the Ag-SAC could be a promising material for the development of high performance breathable biochemical protection clothing.

A kind of functional composite was prepared by loading silver nanoparticles firmly on the surface of spherical activated carbon, which showed chemical adsorption properties for chemical warfare agents and satisfactory antibacterial activity.

Superelastic, Breathable, and High-Barrier Nanofibrous Membranes with Biomimetic ECM Structure for Toxic Chemical Protection

As the last line of protection for humans, chemical protective suits provided safe and effective protection where chemical warfare agents (CWAs) or chemical reagents leaked; however, the existing chemical protective clothing had poor wearing pressure comfort due to the limitation of inherent materials. Herein, we reported a scalable strategy to fabricate chemical protective fabric (CPF) with a biomimetic extracellular matrix (ECM) barrier layer composed of an elastic fiber framework based on the cross-linked nanofiber membrane and the styrene-butadiene-styrene block copolymer (SBS)/acticarbon matrix. The construction of the reliable and strategical biomimetic ECM structure succeeded in fulfilling hazardous chemical barrier properties, recoverable deformation, and thermal comfort improvement. The resulting CPF exhibited waterproofness with exceeding 200 kPa hydrostatic pressure and exceptional WVT of 550.96 g m^-2 d^-1, rapid elastic recovery from a strain of 80%, high-cycle fatigue resistance, superior barrier performance against toxic chemicals, and keeping CEES resistance after 100 tensile loading cycles. The successful preparation of the fascinating biomimetic nanofibrous membrane may provide a particular research foundation for developing chemical protective clothing in the future.

Facemask Global Challenges: The Case of Effective Synthesis, Utilization, and Environmental Sustainability

Coronavirus disease (COVID-19), caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), has caused a rapidly spreading pandemic and is severely threatening public health globally. The human-to-human transmission route of SARS-CoV-2 is now well established. The reported clinical observations and symptoms of this infection in humans appear in the range between being asymptomatic and severe pneumonia. The virus can be transmitted through aerosols and droplets that are released into the air by a carrier, especially when the person coughs, sneezes, or talks forcefully in a closed environment. As the disease progresses, the use and handling of contaminated personal protective equipment and facemasks have become major issues with significant environmental risks. Therefore, providing an effective method for treating used/contaminated facemasks is crucial. In this paper, we review the environmental challenges and risks associated with the surge in facemask production. We also discuss facemasks and their materials as sources of microplastics and how disposal procedures can potentially lead to the contamination of water resources. We herein review the potential of developing nanomaterial-based antiviral and self-cleaning facemasks. This review discusses these challenges and concludes that the use of sustainable and alternative facemask materials is a promising and viable solution. In this context, it has become essential to address the emerging challenges by developing a new class of facemasks that are effective against the virus, while being biodegradable and sustainable. This paper represents the potentials of natural and/or biodegradable polymers for manufacturing facemasks, such as wood-based polymers, chitosan, and other biodegradable synthetic polymers for achieving sustainability goals during and after pandemics.

Controlled Release of Molecular Intercalants from Two-Dimensional Nanosheet Films

Solution co-deposition of two-dimensional (2D) nanosheets with chemical solutes yields nanosheet-molecular heterostructures. A feature of these macroscopic layered hybrids is their ability to release the intercalated molecular agent to express chemical functionality on their surfaces or in their near surroundings. Systematic design methods are needed to control this molecular release to match the demand for rate and lifetime in specific applications. We hypothesize that release kinetics are controlled by transport processes within the layered solids, which primarily involve confined molecular diffusion through nanochannels formed by intersheet van der Waals gaps. Here a variety of graphene oxide (GO)/molecular hybrids are fabricated and subject to transient experiments to characterize release kinetics, locations, and mechanisms. The measured release rate profiles can be successfully described by a numerical model of internal transport processes, and the results used to extract effective Z-directional diffusion coefficients for various film types. The diffusion coefficients are found to be 8 orders of magnitude lower than those in free solution due to nanochannel confinement and serpentine path effects, and this retardation underlies the ability of 2D materials to control and extend release over useful time scales. In-plane texturing of the heterostructured films by compressive wrinkling or crumpling is shown to be a useful design tool to control the release rate for a given film type and molecular intercalant. The potential of this approach is demonstrated through case studies on the controlled release of chemical virucidal agents.

Graphene-triphenyl phosphate (TPP) co-exposure in the marine environment: Interference with metabolism and immune regulation in mussel Mytilus galloprovincialis

Both immune regulation and endocrine systems are great challenges to marine organisms, and effective protocols for determining these adverse outcome pathways are limited, especially in vivo. The increasing usage of graphene nanomaterials can lead to the frequent exposure to marine organisms. Triphenyl phosphate (TPP), an organophosphate flame retardant, is frequently detected in natural environments. In this study, the combined toxic effects of co-exposure to graphene and TPP was investigated in Mytilus galloprovincialis using computational toxicology and multi-omics technology. Noticeably, graphene could disturb the membrane stability and increase the tissue accumulation of TPP. The adsorption behavior of TPP on graphene could inhibit the surface activity of graphene. In the digestive gland, transcriptomics analysis revealed the down-regulated genes in graphene + TPP treatment, including glyceraldehyde-3-phosphate dehydrogenase (GAPDH), sorbitol dehydrogenase (SORD), glutathione s-transferase mu 3 (GSTM3) and 4-aminobutyrate aminotransferase (ABAT), were mainly associated with oxidative stress and energy metabolism. Moreover, metabolic responses indicated that graphene + TPP could cause disturbances in energy metabolism and osmotic regulation marked by differentially altered ATP, glucose and taurine in mussels. These data underline the need for further knowledge on the potential interactions of nanomaterials with existing contaminants in marine organisms.

Chemically modified carbon nanostructures and 2D nanomaterials for fabrics performing under operational tension and extreme environmental conditions

The extensive research on carbon nanostructures and 2D nanomaterials will come to fruition once these materials steadily join everyday-life applications. Their chemical functionalization unlocks their potential as carriers of customized properties and counterparts to fabric fibers. The scope of the current review covers the chemical modification of carbon nanostructures and 2D nanomaterials for hybrid fabrics with enhanced qualities against critical operational and weather conditions, such as antibacterial, flame retardant, UV resistant, water repellent and high air and water vapor permeability activities.

A graphene-based hydrogel monolith with tailored surface chemistry for PFAS passive sampling

Aquatic contamination by per- and polyfluorinated alkyl substances (PFAS) has attracted global attention due to their environmental and health concerns. Current health advisories and surface water regulatory limits require PFAS detection in the parts per trillion (ppt) range. One way to achieve those low detection limits is to use a reliable passive sampling-based monitoring tool for PFAS, as exists for numerous nonpolar persistent organic pollutants. Here we introduce a new graphene-based hydrogel monolith and describe its synthesis, chemical functionalization, property characterization, and testing as a PFAS equilibrium passive sampler. The graphene monoliths were self-assembled by hydrothermal treatment from graphene oxide (GO) aqueous dispersions to produce free standing cylinders of ~563 mm³ volume consisting of ~4 wt-% thin-walled porous graphene and ~96 wt-% water. The uptake of 23 PFAS was measured on the as-produced monoliths, and equilibrium partition coefficients (K_SW), were derived for longer chain (C≥8) perfluoroalkyl acids (PFAA) and neutral precursors such as sulfonamides (log K_SW range 1.9 - 3.6). To increase the K_SW for shorter chain PFAA, the monoliths were chemically modified by a new diazonium-based grafting reaction that introduces positive surface charge without damage to the graphenic backbone. Introduction of benzylamine moieties through the diazonium intermediate switches zeta potential at pH 7 from -45mV (as-produced graphene) to + 5mV. This modification increased the sorption of short and middle chain PFAA by ten-fold (e.g. log K_SW for PFBA increased from 1.3 to 2.2), thereby improving the functionality of the passive sampler device for a wider range of PFAS. Field deployments demonstrated that the graphene monoliths were capable of detecting key PFAS in the Delaware River.

Role of different types of nanomaterials against diagnosis, prevention and therapy of COVID-19

In 2019, a novel type of coronavirus emerged in China called SARS-COV-2, known COVID-19, threatens global health and possesses negative impact on people's quality of life, leading to an urgent need for its diagnosis and remedy. On the other hand, the presence of hazardous infectious waste led to the increase of the risk of transmitting the virus by individuals and by hospitals during the COVID-19 pandemic. Hence, in this review, we survey previous researches on nanomaterials that can be effective for guiding strategies to deal with the current COVID-19 pandemic and also decrease the hazardous infectious waste in the environment. We highlight the contribution of nanomaterials that possess potential to therapy, prevention, detect targeted virus proteins and also can be useful for large population screening, for the development of environmental sensors and filters. Besides, we investigate the possibilities of employing the nanomaterials in antiviral research and treatment development, examining the role of nanomaterials in antiviral- drug design, including the importance of nanomaterials in drug delivery and vaccination, and for the production of medical equipment. Nanomaterials-based technologies not only contribute to the ongoing SARS- CoV-2 research efforts but can also provide platforms and tools for the understanding, protection, detection and treatment of future viral diseases.

Preventing colour fading in artworks with graphene veils

Modern and contemporary art materials are generally prone to irreversible colour changes upon exposure to light and oxidizing agents. Graphene can be produced in thin large sheets, blocks ultraviolet light, and is impermeable to oxygen, moisture and corrosive agents; therefore, it has the potential to be used as a transparent layer for the protection of art objects in museums, during storage and transportation. Here we show that a single-layer or multilayer graphene veil, produced by chemical vapour deposition, can be deposited over artworks to protect them efficiently against colour fading, with a protection factor of up to 70%. We also show that this process is reversible since the graphene protective layer can be removed using a soft rubber eraser without causing any damage to the artwork. We have also explored a complementary contactless graphene-based route for colour protection that is based on the deposition of graphene on picture framing glass for use when the direct application of graphene is not feasible due to surface roughness or artwork fragility. Overall, the present results are a proof of concept of the potential use of graphene as an effective and removable protective advanced material to prevent colour fading in artworks.

Smart Superhydrophobic Textiles Utilizing a Long-Range Antenna Sensor for Hazardous Aqueous Droplet Detection plus Prevention

This paper demonstrates the feasibility of a long-range antenna sensor embedded underneath a liquid repellent fabric to be employed as a wearable sensor in personal protective fabrics. The sensor detects and monitors hazardous aqueous liquids on the outer layer of fabrics, to add an additional layer of safety for professionals working in hazardous environments. A modified patch antenna was designed to include a meandering-shaped resonant structure, which was embedded underneath the fabric. Superhydrophobic fabrics were prepared using silica nanoparticles and a low-surface-energy fluorosilane. 4 to 20 μL droplets representing hazardous aqueous solutions were drop-cast on the fabrics to investigate the performance of the embedded antenna sensor. Long-range (S₂₁) measurements at a distance of 2-3 m were performed using the antenna sensor with treated and untreated fabrics. The antenna sensor successfully detected the liquid for both types of fabrics. The resonant frequency sensitivity of the antenna sensor underneath the treated fabric exhibiting superhydrophobicity was measured as 370 kHz/μL, and 1 MHz/μL for the untreated fabric. The results demonstrate that the antenna sensor is a good candidate for wearable hazardous aqueous droplet detection on fabrics.

2D-Material-integrated hydrogels as multifunctional protective skins for soft robots

Soft robots provide compliant object-machine interactions, but they exhibit insufficient material stability, which restricts them from working in harsh environments. Herein, we developed a class of soft robotic skins based on two-dimensional materials (2DMs) and gelatin hydrogels, featuring skin-like multifunctionality (stretchability, thermoregulation, threat protection, and strain sensing). The 2DM-integrated hydrogel (2DM/H) skins enabled soft robots to execute designated missions in the presence of high levels of heat and various environmental threats while maintaining mild machine temperatures. Via adopting different 2DMs (graphene oxide (GO), montmorillonite (MMT), and titanium carbide (MXene)), the 2DM/H-protected robots were able to perform soft grasping in organic liquids (GO/H) and open fire (MMT/H), and in the presence of electromagnetic radiation and biocontamination (MXene/H). Through blending MXene nanosheets into gelatin, the MXene-blended hydrogel (M-H) skin became strain sensitive, and a GO/M-H gripper exhibited the high-level integration of skin-mimicking capabilities. Finally, we incorporated 2DM/H skins onto an origami-inspired walker robot and a soft batoid-like robot to execute vision-guided searching in fire and underwater locomotion/navigation in chemical spills.

Controlling pore structure and conductivity in graphene nanosheet films through partial thermal exfoliation

Thermal exfoliation is an efficient and scalable method for the production of graphene nanosheets or nanoplatelets, which are typically re-assembled or blended to form new macroscopic "graphene-based materials". Thermal exfoliation can be applied to these macroscopic graphene-based materials after casting to create internal porosity, but this process variant has not been widely studied, and can easily lead to destruction of the physical form of the original cast body. Here we explore how the partial thermal exfoliation of graphene oxide (GO) multilayer nanosheet films can be used to control pore structure and electrical conductivity of planar, textured, and confined GO films. The GO films are shown to exfoliate explosively when the instrument-set heating rates are 100 K/min and above leading to complete destruction of the film geometry. Textured films with engineered micro-wrinkling and crumpling show similar thermal behavior to planar films. Here, we also demonstrate a novel method to produce fairly large size intact rGO films of high electrical conductivity and microporosity based on confinement. Sandwiching GO precursor films between inert plates during partial exfoliation at 250°C produces high conductivity and porosity material in the form of a flexible film that preserves the macroscopic structure of the original cast body.

Exploring the trans-cleavage activity of CRISPR-Cas12a for the development of a Mxene based electrochemiluminescence biosensor for the detection of Siglec-5

Sialic acid-binding immunoglobulin (Ig)-like lectins (Siglecs) is a type I transmembrane receptor on the cell surface. Siglec-5, as one of the Siglecs family, play an important role as an inhibitory receptor for leukocytes in the human body. The development of novel siglec-5 assays can help to study the pathogenesis of related diseases as well as to develop novel therapeutic drugs. We use catalytic hairpin assembly (CHA) amplification strategy combined with CRISPR-Cas12a's side-cutting feature to build a 2D ultra-thin Ti3C2Tx (MXene) based electrochemiluminescence (ECL) biosensor for the detection of Siglec-5. By using this ECL biosensor, the cleavage of CRISPR-Cas12a is reasonably combined with CHA-mediated isothermal amplification, thereby realizing the sensitive amplification assay Siglec-5 with 20.22 fM sensitivity. By introducing pairs of sites that are not in the same double-stranded DNA into the DNA duplex, the hybridization sequence of CRISPR-Cas12a complements the targeting mechanism to enhance indirect Siglec-5 amplification assay. Also, the double-strand DNA (dsDNA) design based on CRISPR-Cas12a amplification allows the same CRISPR RNA (crRNA, also known as guide RNA (gRNA)) to detect the output of DNA duplexes from different intermediate DNAs, which provides a common way for biomarker detection based on the conversion of protein analytes to intermediate DNA strategy. This work extends the application scope of CRISPR-Cas12a to the construction of ECL biosensors, evaluates the role of lectins, which can be used for the biochemical research and clinical diagnosis of protein markers. This is the first investigative work exploring the Trans-Cleavage activity of CRISPR-Cas12a for Mxene-based ECL biosensor establishment to the best of our knowledge.

Intercalation of Dyes in Graphene Oxide Thin Films and Membranes

Intercalation of dyes into thin multilayered graphene oxide (GO) films was studied by neutron reflectivity and X-ray diffraction. Methylene blue (MB) penetrates the interlayer space of GO in ethanol solution and remains intercalated after the solvent evaporation, as revealed by the expansion of the interlayer lattice and change in chemical composition. The sorption of MB by thin GO films is found to be significantly stronger compared to the sorption of Crystal violet (CV) and Rose bengal (RB). This effect is attributed to the difference in the geometrical shape of planar MB and essentially nonflat CV and RB molecules. Graphite oxides and restacked GO films are found to exhibit different methylene blue (MB) sorptions. MB sorption by precursor graphite oxide and thin spin-coated films of GO is significantly stronger compared to freestanding micrometer-thick membranes prepared by vacuum filtration. Nevertheless, the sorption capacity of GO membranes is sufficient to remove a significant part of the MB from diluted solutions tested for permeation in several earlier studies. High sorption capacity results in strong modification of the GO structure, which is likely to affect permeation properties of GO membranes. Therefore, MB is not suitable for testing size exclusion effects in the permeation of GO membranes. It is not only hydration or solvation diameter but also the exact geometrical shape of molecules that needs to be taken into account considering size effects for penetration of molecules between GO layers in membrane applications.

Shear Failure in Supported Two-Dimensional Nanosheet Van der Waals Thin Films

Liquid-phase deposition of exfoliated 2D nanosheets is the basis for emerging technologies that include writable electronic inks, molecular barriers, selective membranes, and protective coatings against fouling or corrosion. These nanosheet thin films have complex internal structures that are discontinuous assemblies of irregularly tiled micron-scale sheets held together by van der Waals (vdW) forces. On stiff substrates, nanosheet vdW films are stable to many common stresses, but can fail by internal delamination under shear stress associated with handling or abrasion. This "re-exfoliation" pathway is an intrinsic feature of stacked vdW films and can limit nanosheet-based technologies. Here we investigate the shear stability of graphene oxide and MoSe₂ nanosheet vdW films through lap shear experiments on polymer-nanosheet-polymer laminates. These sandwich laminate structures fail in mixed cohesive and interfacial mode with critical shear forces from 40 - 140 kPa and fracture energies ranging from 0.2 - 6 J/m². Surprisingly these energies are higher than delamination energies reported for smooth peeling of ordered stacks of continuous 2D sheets, which we propose is due to energy dissipation and chaotic crack motion during nanosheet film disassembly at the crack tip. Experiment results also show that film thickness plays a key role in determining critical shear force (maximum load before failure) and dissipated energy for different nanosheet vdW films. Using a mechanical model with an edge crack in the thin nanosheet film, we propose a shear-to-tensile failure mode transition to explain a maximum in critical shear force for graphene oxide films but not MoSe₂ films. This transition reflects a weakening of the substrate confinement effect and increasing rotational deformation near the film edge as the film thickness increases. For graphene oxide, the critical shear force can be increased by electrostatic cross-linking achieved through interlayer incorporation of metal cations. These results have important implications for the stability of functional devices that employ 2D nanosheet coatings.

Controlling nanochannel orientation and dimensions in graphene-based nanofluidic membranes

There is great interest in exploiting van der Waals gaps in layered materials as nanofluidic channels. Graphene oxide (GO) nanosheets are known to spontaneously assemble into stacked planar membranes with transport properties that are highly selective to molecular structure. Use of conventional GO membranes in liquid-phase applications is often limited by low flux values, due to intersheet nanochannel alignment perpendicular to the desired Z-directional transport, which leads to circuitous fluid pathways that are orders of magnitude longer than the membrane thickness. Here we demonstrate an approach that uses compressive instability in Zr-doped GO thin films to create wrinkle patterns that rotate nanosheets to high angles. Capturing this structure in polymer matrices and thin sectioning produce fully dense membranes with arrays of near-vertically aligned nanochannels. These robust nanofluidic devices offer pronounced reduction in fluid path-length, while retaining the high selectivity for water over non-polar molecules characteristic of GO interlayer nanochannels.

Vertically stacked graphene oxide sheets are promising structures for molecular sieving technologies. By folding large planar sheets in an accordion-like manner, Liu et al. fabricate a thin robust filter with near-vertically aligned nanochannels geared towards commercial separation membranes.

Smart and Sustainable Nanotechnological Solutions in a Battle against COVID-19 and Beyond: A Critical Review

The variety of available biocidal features make nanomaterials promising for fighting infections. To effectively battle COVID-19, categorized as a pandemic by the World Health Organization (WHO), materials scientists and biotechnologists need to combine their knowledge to develop efficient antiviral nanomaterials. By design, nanostructured materials (spherical, two-dimensional, hybrid) can express a diverse bioactivity and unique combination of specific, nonspecific, and mixed mechanisms of antiviral action. It can be related to the material's specific features and their multiple functionalization strategies. This is a complex guiding approach in which an interaction target is constantly moving and quickly changing. On the other hand, in such a rush, sustainability may be put aside. Therefore, to elucidate the most promising nanotechnological solutions, we critically review available data within the frame of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) and other types of viruses. We highlight solutions that are, or could be, more sustainable and less toxic. In this regard, reduction of the number of synthetic routes, organic solvents, byproducts, and residues is highly recommended. Such efficient, green solutions may be further used for the prevention of virion-host interactions, treatment of the already developed infection, reducing inflammation, and finally, protecting healthcare professionals with masks, fabrics, equipment, and in other associated areas. Further translation into the market needs putting on the fast track with respect to principles of green chemistry, feasibility, safety, and the environment.

Swelling properties of graphite oxides and graphene oxide multilayered materials

Graphite oxide (GtO) and graphene oxide (GO) multilayered laminates are hydrophilic materials easily intercalated by water and other polar solvents. By definition, an increase in the volume of a material connected to the uptake of a liquid or vapour is named swelling. Swelling is a property which defines graphite oxides and graphene oxides. Less oxidized materials not capable of swelling should be named oxidized graphene. The infinite swelling of graphite oxide yields graphene oxide in aqueous dispersions. Graphene oxide sheets dispersed in a polar solvent can be re-assembled into multilayered structures and named depending on applications as films, papers or membranes. The multilayered GO materials exhibit swelling properties which are mostly similar to those of graphite oxides but not identical and in some cases surprisingly different. Swelling is a key property of GO materials in all applications which involve the sorption of water/solvents from vapours, immersion of GO into liquid water/solvents and solution based chemical reactions. These applications include sensors, sorption/removal of pollutants from waste waters, separation of liquid and gas mixtures, nanofiltration, water desalination, water-permeable protective coatings, etc. Swelling defines the distance between graphene oxide sheets in solution-immersed GO materials and the possibility for penetration of ions and molecules inside of interlayers. A high sorption capacity of GO towards many molecules and cations is defined by swelling which makes the very high surface area of GO accessible. GtO and GO swelling is a surprisingly complex phenomenon which is manifested in a variety of different ways. Swelling is strongly different for materials produced using the most common Brodie and Hummers oxidation procedures; it depends on the degree of oxidation, ad temperature and pressure conditions. The value of the GO interlayer distance is especially important in membrane applications. Diffusion of solvent molecules and ions is defined by the size of "permeation channels" provided by the swelled GO structure. According to extensive studies performed over the last decade the exact value of the inter-layer distance in swelled GO depends on the nature of solvent, temperature and pressure conditions, and the pH and concentration of solutions and exhibits pronounced aging effects. This review provides insight into the fundamental swelling properties of multilayered GO and demonstrates links to advanced applications of these materials.

Can graphene take part in the fight against COVID-19?

The pneumonia outbreak of coronavirus disease 2019 (COVID-19) represents a global issue. The bidimensional material graphene has captured much attention due to promising antimicrobial applications and has also demonstrated antiviral efficacy. In response to this global outbreak, we summarized the current state of knowledge of graphene and virus interaction as well as possible successful applications to fight COVID-19. Antibody-conjugated graphene sheets can rapidly detect targeted virus proteins and can be useful for large population screening, but also for the development of environmental sensors and filters, given the low cost of graphene materials. Functionalized graphene has demonstrated a good viral capture capacity that, combined with heat or light-mediated inactivation, could be used as a disinfectant. Graphene sensors arrays can be implemented on standard utility textiles and drug efficacy screening. Thanks to its high versatility, we foresee that graphene may have a leading role in the fight against COVID-19.

Can graphene take part in the fight against COVID-19?

The pneumonia outbreak of coronavirus disease 2019 (COVID-19) represents a global issue. The bidimensional material graphene has captured much attention due to promising antimicrobial applications and has also demonstrated antiviral efficacy. In response to this global outbreak, we summarized the current state of knowledge of graphene and virus interaction as well as possible successful applications to fight COVID-19. Antibody-conjugated graphene sheets can rapidly detect targeted virus proteins and can be useful for large population screening, but also for the development of environmental sensors and filters, given the low cost of graphene materials. Functionalized graphene has demonstrated a good viral capture capacity that, combined with heat or light-mediated inactivation, could be used as a disinfectant. Graphene sensors arrays can be implemented on standard utility textiles and drug efficacy screening. Thanks to its high versatility, we foresee that graphene may have a leading role in the fight against COVID-19.

Graphene oxide nanosheets mitigate the developmental toxicity of TDCIPP in zebrafish via activating the mitochondrial respiratory chain and energy metabolism

Graphene oxide (GO), a novel two-dimension carbon nanomaterial, has showed tremendous potential for utilization in intelligent manufacturing and environmental protection. In parallel, tris(1,3-dichloro-2-propyl) phosphate (TDCIPP) is widely distributed in the water environment and represents a great threat to ecosystem health. However, the related knowledge remained absent regarding the impact of GO on the biological risks of TDCIPP. Herein, GO significantly reduced the mortality and malformation rates of zebrafish induced by TDCIPP maximumly by 28.6% and 41.8%, respectively. Decreased mitochondrial respiratory chain (MRC) enzyme and ATP activity induced by TDCIPP were mitigated by GO. Integrating proteomics and metabolomics revealed TDCIPP obviously induced the downregulation of the proteins and metabolites involved in the cytoskeleton, mitochondrial function, carbohydrate and amino acid metabolism, and the TCA cycle, but the alterations were attenuated by GO. GO primarily promoted MRC activity, carbohydrate metabolism, and fatty acid β-oxidation, thus activating the energy metabolism of zebrafish and leading to antagonistic effects on the developmental toxicity of TDCIPP. These results provide a novel view on the co-exposure of GO with other pollutants and promote the reconsideration of the environmental risks of GO.

In situ formation of phosphorus-doped porous graphene via laser induction

Heteroatom-doped graphene exhibits high energy storage performance when used as an active electrode, and which can been applied to various advanced applications, but challenging in synthesis, e.g., hazardous chemical reagents usage, difficult processing steps, and energy consumption. We demonstrated a ready, rapid and normal method for generating phosphorus-doped graphene (LIPG) using a CO2 laser on polyimide (PI) substrate mixed with ammonium polyphosphate (APP) in ambient air. LIPG was approved and successfully synthesized via TEM, SEM, XRD and Raman observations. Moreover, we discussed the flame-retardant performance of APP for synthesizing LIPG on PI substrates, increasing the degree of graphitization. Furthermore, LIPG prepared using supercapacitors as an electrode showed good electrochemical performance. Remarkably, the highest specific capacitance of porous LIPG is about 206 F g-1 at the current density of 0.025 A g-1, the value is about 2 times higher than those undoped laser induced graphene (LIG). Such great performance of the LIPG electrode material is attributed to the formation of a hierarchical porous structure, phosphorus atom doping, and manufacturing deficiency. Hence, LIPG showed considerable potential in the electrochemical application field. The proposed preparation of LIPG is best suited for synthesis and applicable to the doping of other heteroatoms doped into graphene.

Untargeted Metabolic Pathway Analysis as an Effective Strategy to Connect Various Nanoparticle Properties to Nanoparticle-Induced Ecotoxicity

Elucidation of the relationships between nanoparticle properties and ecotoxicity is a fundamental issue for environmental applications and risk assessment of nanoparticles. However, effective strategies to connect the various properties of nanoparticles with their ecotoxicity remain largely unavailable. Herein, an untargeted metabolic pathway analysis was employed to investigate the environmental risk posed by 10 typical nanoparticles (AgNPs, CuNPs, FeNPs, ZnONPs, SiO₂NPs, TiO₂NPs, GO, GOQDs, SWCNTs, and C₆₀) to rice (a staple food for half of the world's population). Downregulation of carbohydrate metabolism and upregulation of amino acid metabolism were the two dominant metabolic effects induced by all tested nanoparticles. Partial least-squares regression analysis indicated that a zerovalent metal and high specific surface area positively contributed to the downregulation of carbohydrate metabolism, indicating strong abiotic stress. In contrast, the carbon type, the presence of a spherical or sheet shape, and the absence of oxygen functional groups in the nanoparticles positively contributed to the upregulation of amino acid metabolism, indicating adaptation to abiotic stress. Moreover, network relationships among five properties of nanoparticles were established for these metabolic pathways. The results of the present study will aid in the understanding and prediction of environmental risks and in the design of environmentally friendly nanoparticles.

Graphene Oxide-Based Membrane as a Protective Barrier against Toxic Vapors and Gases

Traditional protective garments loaded with activated carbons to remove toxic gases are very bulky. Novel graphene oxide (GO) flake-based composite lamellar membrane structure is being developed as a potential component of a garment for protection against chemical warfare agents (CWAs) represented here by simulants, dimethyl methyl phosphonate (DMMP) (a sarin-simulant), and 2-chloroethyl ethyl sulfide (CEES) (a simulant for sulfur mustard), yet allowing a high-moisture transmission rate. GO flakes of dimensions 300-800 nm, 0.7-1.2 nm thickness and dispersed in an aqueous suspension were formed into a membrane by vacuum filtration on a porous poly(ether sulfone) (PES) or poly(ether ether ketone) (PEEK) support membrane for noncovalent π-π interactions with GO flakes. After physical compression of such a membrane, upright cup tests indicated that it can block toluene for 3-4 days and DMMP for 5 days while exhibiting excellent water vapor permeation. Further, they display very low permeances for small-molecule gases/vapors. The GO flakes underwent cross-linking later with ethylenediamine (EDA) introduced during the vacuum filtration followed by physical compression and heating. With a further spray coating of polyurethane (PU), these membranes could be bent without losing barrier properties vis-à-vis the CWA simulant DMMP for 5 days; a membrane not subjected to bending blocked DMMP for 15 days. For the PEEK-EDA-GO-PU-compressed membranes after bending, the separation factors of H₂O over other species for low gas flow rates in the dynamic moisture permeation cell (DMPC) are: α_H2O-He is 42.3; α_H2O-N2 is 110; and α_H2O-ethane is 1800. At higher gas flow rates in the DMPC, the moisture transmission rate goes up considerably due to reduced boundary layer resistances and exceeds the threshold water vapor flux of 2000 g/(m²·day) that defines a breathable fabric. This membrane displayed considerable resistance to permeation by CEES as well. The PES-EDA-GO-PU-compressed membrane shows good mechanical property under tensile strength tests.

Emerging Developments in the Use of Electrospun Fibers and Membranes for Protective Clothing Applications

There has been increased interest to develop protective fabrics and clothing for protecting the wearer from hazards such as chemical, biological, heat, UV, pollutants etc. Protective fabrics have been conventionally developed using a wide variety of techniques. However, these conventional protective fabrics lack breathability. For example, conventional protective fabrics offer good protection against water but have limited ability in removing the water vapor and moisture. Fibers and membranes fabricated using electrospinning have demonstrated tremendous potential to develop protective fabrics and clothing. These fabrics based on electrospun fibers and membranes have the potential to provide thermal comfort to the wearer and protect the wearer from wide variety of environmental hazards. This review highlights the emerging applications of electrospinning for developing such breathable and protective fabrics.

Mosquito bite prevention through graphene barrier layers

Graphene-based materials are being developed for a variety of wearable technologies to provide advanced functions that include sensing; temperature regulation; chemical, mechanical, or radiative protection; or energy storage. We hypothesized that graphene films may also offer an additional unanticipated function: mosquito bite protection for light, fiber-based fabrics. Here, we investigate the fundamental interactions between graphene-based films and the globally important mosquito species, Aedes aegypti, through a combination of live mosquito experiments, needle penetration force measurements, and mathematical modeling of mechanical puncture phenomena. The results show that graphene or graphene oxide nanosheet films in the dry state are highly effective at suppressing mosquito biting behavior on live human skin. Surprisingly, behavioral assays indicate that the primary mechanism is not mechanical puncture resistance, but rather interference with host chemosensing. This interference is proposed to be a molecular barrier effect that prevents Aedes from detecting skin-associated molecular attractants trapped beneath the graphene films and thus prevents the initiation of biting behavior. The molecular barrier effect can be circumvented by placing water or human sweat as molecular attractants on the top (external) film surface. In this scenario, pristine graphene films continue to protect through puncture resistance-a mechanical barrier effect-while graphene oxide films absorb the water and convert to mechanically soft hydrogels that become nonprotective.

Mesoporous bioactive glass combined with graphene oxide scaffolds for bone repair

Recently there has been an increasing interest in bioactive factors with robust osteogenic ability and angiogenesis function to repair bone defects. However, previously tested factors have not achieved satisfactory results due to low loading doses and a short protein half-life. Finding a validated stable substitute for these growth factors and apply it to the construction of porous scaffolds with the dual function of osteogenesis and angiogenesis is therefore vital for bone tissue regeneration engineering. Graphene oxide (GO) has attracted increasing attention due to its good biocompatibility, osteogenic, and angiogenic functions. This study aims to design a scaffold composed of mesoporous bioactive glasses (MBG) and GO to investigate whether the composite porous scaffold promotes local angiogenesis and bone healing. Our in vitro studies demonstrate that the MBG-GO scaffolds have better cytocompatibility and higher osteogenesis differentiation ability with rat bone marrow mesenchymal stem cells (rBMSCs) than the purely MBG scaffold. Moreover, MBG-GO scaffolds promote vascular ingrowth and, importantly, enhance bone repair at the defect site in a rat cranial defect model. The new bone was fully integrated not only with the periphery but also with the center of the scaffold. From these results, it is believed that the MBG-GO scaffolds possess excellent osteogenic-angiogenic properties which will make them appealing candidates for repairing bone defects. The novelty of this research is to provide a new material to treat bone defects in the clinic.

Graphene oxide quantum dots stimulate indigenous bacteria to remove oil contamination

Oil spills occur frequently worldwide, resulting in severe damage to water and to human health. Polycyclic aromatic hydrocarbons (PAHs) are the primary toxic components in oil contamination. PAH-degrading microbes have attracted significant attention, but difficulty in their selection and proliferation limits their applications. Graphene oxide quantum dots (GOQDs) improve the proliferation of an indigenous PAH-degrading strain, Bacillus cereus, more effectively than large graphene oxide flakes. Bacillus cereus can metabolize a variety of xenobiotic aromatic compounds as carbon sources and is used in bioremediation. GOQDs contain a variety of aromatic hydrocarbon structures, explaining why the bacteria achieve strong tolerance to PAHs. GOQD-activated cytokinesis increases the secretion of substances important for biofilm formation (extracellular polymeric substances), which further accelerates PAH removal. Proteomic analysis reveals the molecular mechanisms underlying GOQD-induced microbial proliferation. GOQDs induce the overexpression of microbial divisomal proteins associated with division initiation, DNA replication and peptidoglycan hydrolysis/synthesis. Importantly, PAH removal mediated by GOQD-treated Bacillus cereus does not require the addition of GOQDs. The effects of GOQDs on a strain persist for at least 20 generations, suggesting their possible use in low-cost applications. This work proposes a strategy to remove oil contamination using an indigenous bacterial system enhanced by nanomaterials.

Hierarchical Reduced Graphene Oxide Ridges for Stretchable, Wearable, and Washable Strain Sensors

Recently, flexible and wearable devices are increasingly in demand and graphene has been widely used due to its exceptional chemical, mechanical and electrical properties. Building complex buckling patterns of graphene is an essential strategy to increase its flexible and stretchable properties. Herein, a facile dimensionally controlled four-dimensional (4D) shrinking method was proposed to generate hierarchical reduced graphene oxide (rGO) buckling patterns on curved substrates mimicking different parts of the uniforms. The reduced graphene oxide ridges (rGORs) generated on the spherical substrate seem isotropic, while those generated on the cylindrical substrate are obviously more hierarchical or oriented, especially when the cylindrical substrate are shrinking via two steps. The oriented rGORs are superhydrophobic and strain sensitive but obviously anisotropic along the axial and circumferential directions. The sensitivity of rGORs along the axial direction is much higher than those along the circumferential direction. In addition, the intrinsic solvent barrier property of graphene enables the crack-free rGORs an excellent chemical protective performance, withstanding DCM immersion for more than 2.5 h. The flexible rGORs-based strain sensors can be used to detect both large and subtle human motions and activities by achieving high sensitivity (maximum gauge factor up to 48), high unidirectional stretchability (300-530%), and ultrahigh areal stretchability (up to 2690%). Excellent durability was also demonstrated for human motion monitoring with resistance to hand rubbing, ultrasonic cleaning, machine washing, and chemical immersion.

Flexible SIS/HKUST-1 Mixed Matrix Composites as Protective Barriers against Chemical Warfare Agent Simulants

We fabricated and demonstrated, for the first time, metal-organic framework (MOF), polymer mixed-matrix composites (MMCs) as effective, low burden barriers against chemical warfare agent (CWA) simulants. We incorporated the MOF HKUST-1 into elastomeric triblock copolymers of polystyrene- block-polyisoprene- block-polystyrene (SIS) for use as semipermeable barrier against the CWA simulant 2-chloroethyl ethyl sulfide (CEES). MMCs containing up to 50 wt % HKUST-1 were cast and evaluated for CEES permeation, moisture vapor transport rate (MVTR), and mechanical properties, such as elastic modulus and percent elongation. Increasing the MOF content resulted in longer protection against CEES with breakthrough times ranging from immediate breakthrough for the baseline SIS to over 4000 min for the best-performing MMC. MVTRs of high-MOF-content MMCs were approximately 5-10 times higher than either SIS or typical laboratory gloves made from nitrile and latex. The elastic moduli increased with increased MOF content corresponding to a reduction in percent elongation. The triblock copolymer also was found to protect the MOF crystal structure after exposure to CEES and liquid water, which may lead to longer usage time and shelf life. The ability to resist degradation due to moisture shows the potential utility of these composites when exposed to rain, sweat, or other moisture-rich environments. Finally, the MOF-containing composites functioned as robust colorimetric indicators of CEES exposure. Thus, these MMC materials present a potential route toward next-generation personal protective equipment with a combination of detoxification, sensing, environmental stability, and thermal/user-comfort properties not present in current materials solutions.

Multifunctionality and Mechanical Actuation of 2D Materials for Skin-Mimicking Capabilities

Human skin serves as a multifunctional organ with remarkable properties, such as sensation, protection, regulation, and mechanical stretchability. The mimicry of skin's multifunctionalities via various nanomaterials has become an emerging topic. 2D materials have attracted much interest in the field of skin mimicry due to unique physiochemical properties. Herein, recent developments of using various 2D materials to mimic skin's sensing, protecting, and regulating capabilities are summarized. Next, to endow high stretchability to 2D materials, the approaches for fabrication of stretchable bilayer structures by integrating higher dimensional 2D materials onto soft elastomeric substrates are introduced. Accordion-like 2D material structures can elongate with elastomers and undergo programmed folding/unfolding processes to mimic skin's stretchability. That stretchable 2D material devices can achieve effective tactile sensing and protecting capabilities under large deformation is then highlighted. Finally, multiple key directions and existing challenges for future development are discussed.

Sulfur-Doped Laser-Induced Porous Graphene Derived from Polysulfone-Class Polymers and Membranes

Graphene based materials have profoundly impacted research in nanotechnology, and this has significantly advanced biomedical, electronics, energy, and environmental applications. Laser-induced graphene (LIG) is made photothermally and has enabled a rapid route for graphene layers on polyimide surfaces. However, polysulfone (PSU), poly(ether sulfone) (PES), and polyphenylsulfone (PPSU) are highly used in numerous applications including medical, energy, and water treatment and they are critical components of polymer membranes. Here we show LIG fabrication on PSU, PES, and PPSU resulting in conformal sulfur-doped porous graphene embedded in polymer dense films or porous substrates using reagent- and solvent-free methods in a single step. We demonstrate the applicability as flexible electrodes with enhanced electrocatalytic hydrogen peroxide generation, as antifouling surfaces and as antimicrobial hybrid membrane-LIG porous filters. The properties and surface morphology of the conductive PSU-, PES-, and PPSU-LIG could be modulated using variable laser duty cycles. The LIG electrodes showed enhanced hydrogen peroxide generation compared to LIG made on polyimide, and showed exceptional biofilm resistance and potent antimicrobial killing effects when treated with Pseudomonas aeruginosa and mixed bacterial culture. The hybrid PES-LIG membrane-electrode ensured complete elimination of bacterial viability in the permeate (6 log reduction), in a flow-through filtration mode at a water flux of ∼500 L m^-2 h^-1 (2.5 V) and at ∼22 000 L m^-2 h^-1 (20 V). Due to the widespread use of PSU, PES, and PPSU in modern society, these functional PSU-, PES-, and PPSU-LIG surfaces have great potential to be incorporated into biomedical, electronic, energy and environmental devices and technologies.

Ultrastretchable Graphene-Based Molecular Barriers for Chemical Protection, Detection, and Actuation

A wide range of technologies requires barrier films to impede molecular transport between the external environment and a desired internal microclimate. Adding stretchability to barrier films would enable the applications in packaging, textiles, and flexible devices, but classical barrier materials utilize dense, ordered molecular architectures that easily fracture under small tensile strain. Here, we show that textured graphene-based coatings can serve as ultrastretchable molecular barriers expandable to 1500% areal strain through programmed unfolding that mimics the elasticity of polymers. These coatings retain barrier function under large deformation and can be conformally applied to planar or curved surfaces, where they are washfast and mechanically robust to cycling. These graphene-polymer bilayer structures also function as sensors or actuators by transducing chemical stimuli into mechanical deformation and electrical resistance change through asymmetric polymer swelling. These results may enable multifunctional fabrics that integrate chemical protection, sensing, and actuation, with further applications as selective barriers, membranes, stretchable electronics, or soft robotics.