Aeropectin: Fully Biomass-Based Mechanically Strong and Thermal Superinsulating Aerogel

From Cellulose Solutions to Aerogels and Xerogels: Controlling Properties for Drug Delivery

A cheap and easy-to-recycle solvent, namely, aqueous NaOH with no additives, was used to dissolve cellulose and make cross-linker-free materials with varying porosity, testing them as drug delivery devices. Cellulose solutions were gelled, coagulated in a nonsolvent (water, ethanol), and dried either using supercritical CO2 (aerogels) or low-vacuum evaporation (named "xerogels"). Aerogels had densities of around 0.1 g/cm3 and specific surface areas (SSAs) of 200-400 m2/g. A significant influence of the first nonsolvent and drying mode on material properties was recorded: when the first nonsolvent was ethanol and low-vacuum drying was performed from ethanol, aerogel-like xerogels were obtained with densities of around 0.2 g/cm3 and SSAs of 200-260 m2/g. Other conditions (under evaporative drying) resulted in cellulose with much lower porosity and SSA. All materials were evaluated as drug delivery devices in simulated gastrointestinal fluids; theophylline was used as a model drug. Materials of high porosity exhibited shrinking and rapid drug release, whereas denser materials swelled and showed slower release. Two release mechanisms were suggested: diffusion through aqueous media in pores and diffusion through swollen pore walls. The results demonstrate a large spectrum of options for tuning the properties of porous cellulose materials for drug release applications.

Tuning bio-aerogel properties. Part 3: Exploring silica-pectin composite aerogels for drug delivery

The release of the model drug theophylline from silica-pectin aerogels was investigated. The composite aerogels were prepared via impregnation of pectin alcogels with silica sol, followed by in situ silica gelation and drying with supercritical CO2. The structural and physico-chemical properties of the aerogels were tuned via the preparation conditions (type of silica sol, calcium crosslinking of pectin or not). Theophylline was loaded via impregnation and its release into simulated gastric fluid was studied during 1 h followed by release into simulated intestinal fluid. The swelling, mass loss and theophylline release behavior of the composites were analyzed and correlated with material properties. It followed that only aerogels prepared with calcium-crosslinked pectin and polyethoxydisiloxane were stable in aqueous systems, exhibiting a slow theophylline release governed by near-Fickian diffusion.

Ionic-physical-chemical triple cross-linked all-biomass-based aerogel for thermal insulation applications

Aerogels, as a unique porous material, are expected to be used as insulation materials to solve the global environmental and energy crisis. Using chitosan, citric acid, pectin and phytic acid as raw materials, an all-biomass-based aerogel with high modulus was prepared by the triple strategy of ionic, physical and chemical cross-linking through directional freezing technique. Based on this three-dimensional network, the aerogel exhibited excellent compressive modulus (24.89 ± 1.76 MPa) over a wide temperature range and thermal insulation properties. In the presence of chitosan, citric acid and phytic acid, the aerogel obtained excellent fire safety (LOI value up to 31.2%) and antibacterial properties (antibacterial activity against Staphylococcus aureus and Escherichia coli reached 81.98% and 67.43%). In addition, the modified aerogel exhibited excellent hydrophobicity (hydrophobic angle of 146°) and oil-water separation properties. More importantly, the aerogel exhibited a biodegradation rate of up to 40.31% for 35 days due to its all-biomass nature. This work provides a green and sustainable strategy for the production of highly environmentally friendly thermal insulation materials with high strength, flame retardant, antibacterial and hydrophobic properties.

Hydrophobic Modification of Pectin Aerogels via Chemical Vapor Deposition

Pectin aerogels, with very low density (around 0.1 g cm-3) and high specific surface area (up to 600 m2 g-1), are excellent thermal insulation materials since their thermal conductivity is below that of air at ambient conditions (0.025 W m-1 K-1). However, due to their intrinsic hydrophilicity, pectin aerogels collapse when in contact with water vapor, losing superinsulating properties. In this work, first, pectin aerogels were made, and the influence of the different process parameters on the materials' structure and properties were studied. All neat pectin aerogels had a low density (0.04-0.11 g cm-1), high specific surface area (308-567 m2 g-1), and very low thermal conductivity (0.015-0.023 W m-1 K-1). Then, pectin aerogels were hydrophobized via the chemical vapor deposition of methyltrimethoxysilane using different reaction durations (2 to 24 h). The influence of hydrophobization on material properties, especially on thermal conductivity, was recorded by conditioning in a climate chamber (25 °C, 80% relative humidity). Hydrophobization resulted in the increase in thermal conductivity compared to that of neat pectin aerogels. MTMS deposition for 16 h was efficient for hydrophobizing pectin aerogels in moist environment (contact angle 115°) and stabilizing material properties with no fluctuation in thermal conductivity (0.030 W m-1 K-1) and density for the testing period of 8 months.

Additive Manufacturing of Nanocellulose Aerogels with Structure-Oriented Thermal, Mechanical, and Biological Properties

Additive manufacturing (AM) is widely recognized as a versatile tool for achieving complex geometries and customized functionalities in designed materials. However, the challenge lies in selecting an appropriate AM method that simultaneously realizes desired microstructures and macroscopic geometrical designs in a single sample. This study presents a direct ink writing method for 3D printing intricate, high-fidelity macroscopic cellulose aerogel forms. The resulting aerogels exhibit tunable anisotropic mechanical and thermal characteristics by incorporating fibers of different length scales into the hydrogel inks. The alignment of nanofibers significantly enhances mechanical strength and thermal resistance, leading to higher thermal conductivities in the longitudinal direction (65 mW m-1 K-1) compared to the transverse direction (24 mW m-1 K-1). Moreover, the rehydration of printed cellulose aerogels for biomedical applications preserves their high surface area (≈300 m2 g-1) while significantly improving mechanical properties in the transverse direction. These printed cellulose aerogels demonstrate excellent cellular viability (>90% for NIH/3T3 fibroblasts) and exhibit robust antibacterial activity through in situ-grown silver nanoparticles.

Pectin Nanoporous Structures Prepared via Salt-Induced Phase Separation and Ambient Azeotropic Evaporation Processes

Polysaccharide nanoporous structures are suitable for various applications, ranging from biomedical scaffolds to adsorption materials, owing to their biocompatibility and large surface areas. Pectin, in particular, can create 3D nanoporous structures in aqueous solutions by binding with calcium cations and creating nanopores by phase separation; this process involves forming hydrogen bonds between alcohols and pectin chains in water and alcohol mixtures and the resulting penetration of alcohols into calcium-bound pectin gels. However, owing to the dehydration and condensation of polysaccharide chains during drying, it has proven to be challenging to maintain the 3D nanoporous structure without using a freeze-drying process or supercritical fluid. Herein, we report a facile method for creating polysaccharide-based xerogels, involving the co-evaporation of water with a nonsolvent (e.g., a low-molecular-weight hydrophobic alcohol such as isopropyl or n-propyl alcohol) at ambient conditions. Experiments and coarse-grained molecular dynamics simulations confirmed that salt-induced phase separation and hydrogen bonding between hydrophobic alcohols and pectin chains were the dominant processes in mixtures of pectin, water, and hydrophobic alcohols. Furthermore, the azeotropic evaporation of water and alcohol mixed in approximately 1:1 molar ratios was maintained during the natural drying process under ambient conditions, preventing the hydration and aggregation of the hydrophilic pectin chains. These results introduce a simple and convenient process to produce 3D polysaccharide xerogels under ambient conditions.

Superelastic and superflexible cellulose aerogels for thermal insulation and oil/water separation

Aerogels with low thermal conductivity and high adsorption capacity present a promising solution to curb water pollution caused by organic reagents as well as mitigate heat loss. Although aerogels exhibiting good adsorption capacity and thermal insulation have been reported, materials with mechanical integrity, high flexibility and shear resistance still pose a formidable task. Here, we produced bacterial cellulose-based ultralight multifunctional hybrid aerogels by using freeze-drying followed by chemical vapor deposition silylation method. The hybrid aerogels displayed a low density of 10-15 mg/cm3, high porosity exceeding 99.1 %, low thermal conductivity (27.3-29.2 mW/m.K) and superior hydrophobicity (water contact angle>120o). They also exhibited excellent mechanical properties including superelasticity, high flexibility and shear resistance. The hybrid aerogels demonstrated high heat shielding efficiency when used as an insulating material. As a selective oil absorbent, the hybrid aerogels exhibit a maximum adsorption capacity of up to approximately 156 times its own weight and excellent recoverability. Especially, the aerogel's highly accessible porous microstructure results in an impressive flux rate of up to 162 L/h.g when used as a filter in a continuous oil-water separator to isolate n-hexane-water mixtures. This work presents a novel endeavor to create high-performance, sustainable, reusable, and adaptable multifunctional aerogels.

Hybrid Materials of Bio-Based Aerogels for Sustainable Packaging Solutions

This review explores the field of hybrid materials in the context of bio-based aerogels for the development of sustainable packaging solutions. Increasing global concern over environmental degradation and the growing demand for environmentally friendly alternatives to conventional packaging materials have led to a growing interest in the synthesis and application of bio-based aerogels. These aerogels, which are derived from renewable resources such as biopolymers and biomass, have unique properties such as a lightweight structure, excellent thermal insulation, and biodegradability. The manuscript addresses the innovative integration of bio-based aerogels with various other materials such as nanoparticles, polymers, and additives to improve their mechanical, barrier, and functional properties for packaging applications. It critically analyzes recent advances in hybridization strategies and highlights their impact on the overall performance and sustainability of packaging materials. In addition, the article identifies the key challenges and future prospects associated with the development and commercialization of hybrid bio-based aerogel packaging materials. The synthesis of this knowledge is intended to contribute to ongoing efforts to create environmentally friendly alternatives that address the current problems associated with conventional packaging while promoting a deeper understanding of the potential of hybrid materials for sustainable packaging solutions.

Incorporation of Cellulose-Based Aerogels into Textile Structures

Given their exceptional attributes, aerogels are viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porosity, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textiles sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogels' formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multifunctionality of cellulose-based aerogels in the textiles industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Biopolymer-Polysiloxane Double Network Aerogels

A new series of transparent aerogels of biopolymer-polysiloxane double networks is reported. Biopolymer aerogels have attracted much attention from green and sustainable aspects but suffered from strong hydrophilicity and difficulty to make homogeneous structures in nanoscale; these drawbacks are overcome by compositing with a polysiloxane network. Alginate-polymethylsilsesquioxane aerogel has high optical transparency, water repellency, comparable superinsulation property and improved bending flexibility compared to pure polymethylsilsesquioxane aerogel. The nanoscale homogeneity is realized by separating the crosslinking steps for two networks in a sequential protocol: condensation of siloxane bonds and metal-crosslinking of biopolymer. The crosslinking order, biopolymer-first or siloxane-first, and universality/limitation of biopolymer-crosslinker pairs are discussed to construct fundamental chemistry of double network systems for their further application potentials.

Hyaluronic Acid Aerogels Made Via Freeze-Thaw-Induced Gelation

The biodegradability, biocompatibility, and bioactivity of hyaluronic acid (HA), a natural polysaccharide, combined with the low density, high porosity, and high specific surface area of aerogels attract interest for biomedical applications such as wound dressings. In this work, physically cross-linked HA aerogels were prepared via the freeze-thaw (FT) induced gelation method, solvent exchange, and drying with supercritical CO2. The morphology and properties of HA aerogels (volume shrinkage, density, and specific surface area) were investigated as a function of several process parameters: HA concentration, solution pH, number of FT cycles, and type of nonsolvent used during solvent exchange. We demonstrate that the HA solution pH plays a key role in the aerogel formation, as not all conditions result in materials with high specific surface area. HA aerogels were of low density (<0.2 g/cm3), high specific surface area (up to 600 m2/g), and high porosity (≥90%). Scanning electron microscopy pictures revealed that HA aerogels present a porous structure with meso- and small macropores. The results show that HA aerogels are promising biomaterials with tunable properties and internal structure that offer high potential as, e.g., wound dressings.

Study on the Influence of the Preparation Method of Konjac Glucomannan-Silica Aerogels on the Microstructure, Thermal Insulation, and Flame-Retardant Properties

Natural polysaccharides with high viscosity, good thermal stability, and biocompatibility can improve the mechanical properties of inorganic silica aerogels and enhance their application safety. However, the effects of the preparation methods of polysaccharide-silica aerogels on their microstructure and application properties have not been systematically studied. To better investigate the effect of the microstructure on the properties of aerogel materials, two aerogels with different structures were prepared using Konjac glucomannan (KGM) and tetraethoxysilane (TEOS) via physical blending (KTB) and co-precursor methods (KTC), respectively. The structural differences between the KTB and KTC aerogels were characterized, and the thermal insulation and fire-retardant properties were further investigated. The compressive strength of the KTC aerogels with a cross-linked interpenetrating network (IPN) structure was three times higher than that of the KTB aerogels, while their thermal conductivity was 1/3 of that of the KTB aerogels. The maximum limiting oxygen index (LOI) of the KTC aerogels was 1.4 times, the low peak heat release rate (PHRR) was reduced by 61.45%, and the lowest total heat release (THR) was reduced by 41.35% compared with the KTB aerogels. The results showed that the KTC aerogels with the IPN have better mechanical properties, thermal insulation, and fire-retardant properties than the simple physically blending KTB aerogels. This may be due to the stronger hydrogen-bonding interactions between KGM and silica molecules in the KTC aerogels under the unique forcing effect of the IPN, thus enhancing their structural stability and achieving complementary properties. This work will provide new ideas for the microstructure design of aerogels and the research of new thermal insulation and fire-retardant aerogels.

Closed-Loop Recyclable High-Performance Polyimine Aerogels Derived from Bio-Based Resources

Organic aerogels are an intriguing class of highly porous and ultralight materials which have found widespread applications in thermal insulation, energy storage, and chemical absorption. These fully cross-linked polymeric networks, however, pose environmental concerns as they are typically made from fossil-based feedstock and the recycling back to their original monomers is virtually impossible. In addition, organic aerogels suffer from low thermal stability and potential fire hazard. To overcome these obstacles and create next-generation organic aerogels, a set of polyimine aerogels containing reversible chemical bonds which can selectively be cleaved on demand is prepared. As precursors, different primary amines and cyclophosphazene derivatives made from bio-based reagents (vanillin and 4-hydroxybenzaldehyde) to elevate the thermal stability and reduce the environmental impact are used. The resulting polyimine aerogels exhibit low shrinkage, high porosity, large surface area, as well as pronounced thermal stability and flame resistance. More importantly, the aerogels show excellent recyclability under acidic conditions with high monomer recovery yields and purities. This approach allows for preparation of fresh aerogels from the retrieved building blocks, thus demonstrating efficient closed-loop recycling. These high-performance, recyclable, and bio-based polyimine aerogels pave the way for advanced and sustainable superinsulating materials.

Trends and challenges in the development of bio-based barrier coating materials for paper/cardboard food packaging; a review

Currently, petroleum-based synthetic plastics are used as a key barrier material in the paper-based packaging of several food and nonfood goods. This widespread usage of plastic as a barrier lining is not only harmful to human and marine health, but it is also polluting the ecosystem. Researchers and food manufacturers are focused on biobased alternatives because of its numerous advantages, including biodegradability, biocompatibility, non-toxicity, and structural flexibility. When used alone or in composites/multilayers, these biobased alternatives provide strong barrier qualities against grease, oxygen, microbes, air, and water. According to the most recent literature reports, biobased polymers for barrier coatings are having difficulty breaking into the business. Technological breakthroughs in the field of bioplastic production and application are rapidly evolving, proffering new options for academics and industry to collaborate and develop sustainable packaging solutions. Existing techniques, such as multilayer coating of nanocomposites, can be improved further by designing them in a more systematic manner to attain the best barrier qualities. Modified nanocellulose, lignin nanoparticles, and bio-polyester are among the most promising future candidates for nanocomposite-based packaging films with high barrier qualities. In this review, the state-of-art and research advancements made in biobased polymeric alternatives such as paper and board barrier coating are summarized. Finally, the existing limitations and potential future development prospects for these biobased polymers as barrier materials are reviewed.

Impact of Crosslinking on the Characteristics of Pectin Monolith Cryogels

In this research, the pectin monoliths were prepared via the sol-gel process through different routes of crosslinking and additional freeze-drying. The crosslinking reaction was induced by the use of calcium ions in aqueous solutions and in alcohol/water solutions. The resulting pectin monoliths obtained by freeze-drying were macroporous with open cells, limited specific surface area, moderate mechanical stability and moderate biodegradation rate. The presence of alcohol in crosslinking solution significantly changed the morphology of final pectin monoliths, which was evidenced by the reduction of their pore size for one order. The specific surface area of pectin monoliths obtained through the calcium-water-alcohol route was 25.7 m²/g, the Young compressive modulus was 0.52 MPa, and the biodegradation rate was 45% after 30 days of immersion in compost media. Considering that pectin can be obtained from food waste, and its physical properties could be tailored by different crosslinking routes, the pectin monoliths could find wide application in the pharmaceutical, agricultural, medical and food industries, providing sustainable development concepts.

Optimization of the Sound Absorption Coefficient (SAC) from Cellulose-Silica Aerogel Using the Box-Behnken Design

Noise pollution, which has become a major environmental issue in urban areas, can be minimized using acoustic insulation derived from cellulose-silica aerogel. The raw materials required in the process include waste newspaper-based cellulose, geothermal silica, and NaOH/ZnO solution. Therefore, this study investigates the effect of cellulose, silica, and ZnO concentrations on optimizing the sound absorption coefficient (SAC) using the Box-Behnken design (BBD). The results showed that the optimum conditions were obtained at 39.8578 wt % cellulose, 16.5428 wt % silica, and 0.5684 wt % ZnO. The impedance test for the cellulose aerogel and cellulose-silica aerogel showed SAC values of 0.59 and 0.70, respectively, and were characterized by XRD, FTIR, BET-BJH, SEM-EDX, and TG. The results of XRD and FTIR data indicate that the product was cellulose-silica aerogel, and the SEM micrographs showed that silica particles were attached to the fiber surface. Furthermore, type IV isotherms were observed in the cellulose-silica aerogel, typical of mesoporous materials. The presence of silica strengthened the aerogel structure, improved its thermal stability, and increased the surface area but decreased its pore size.

Superinsulating nanocellulose aerogels: Effect of density and nanofiber alignment

Cellulose aerogels are potential alternatives to silica aerogels with advantages in cost, sustainability and mechanical properties. However, the density dependence of thermal conductivity (λ) for cellulose aerogels remains controversial. Cellulose aerogels were produced by gas-phase pH induced gelation of TEMPO-oxidized cellulose nanofibers (CNF) and supercritical drying. Their properties are evaluated by varying the CNF concentration (5-33 mg·cm^-3) and by uniaxial compression (9-115 mg·cm^-3). The aerogels are transparent with specific surface areas of ~400 m²·g^-1, mesopore volumes of ~2 cm³·g^-1 and a power-law dependence of the E-modulus (α ~ 1.53, and the highest reported E of ~1 MPa). The dataset confirms that λ displays a traditional U-shaped density dependence with a minimum of 18 mW·m^-1·K^-1 at 0.065 g·cm^-3. For a given density, λ is ~5 mW·m^-1·K^-1 lower for compressed aerogels due to the alignment of nanofibers, confirmed by small angle X-ray scattering (SAXS).

A Brief Evaluation of Pore Structure Determination for Bioaerogels

This review discusses the most commonly employed methods for determining pore size and pore size distribution in bioaerogels. Aerogels are materials with high porosity and large surface areas. Most of their pores are in the range of mesopores, between 2 and 50 nm. They often have smaller or larger pores, which presents a significant challenge in determining the exact mean pore size and pore size distribution in such materials. The precision and actual value of the pore size are of considerable importance since pore size and pore size distribution are among the main properties of aerogels and are often directly connected with the final application of those materials. However, many recently published papers discuss or present pore size as one of the essential achievements despite the misinterpretation or the wrong assignments of pore size determination. This review will help future research and publications evaluate the pore size of aerogels more precisely and discuss it correctly. The study covers methods such as gas adsorption, from which BJH and DFT models are often used, SEM, mercury porosimetry, and thermoporometry. The methods are described, and the results obtained are discussed. The following paper shows that there is still no precise method for determining pore size distribution or mean pore size in aerogels until now. Knowing that, it is expected that this field will evolve in the future.

Nanocellulose-Based Composite Materials Used in Drug Delivery Systems

Nanocellulose has lately emerged as one of the most promising "green" materials due to its unique properties. Nanocellulose can be mainly divided into three types, i.e., cellulose nanocrystals (CNCs), cellulose nanofibrils (CNFs), and bacterial cellulose (BC). With the rapid development of technology, nanocellulose has been designed into multidimensional structures, including 1D (nanofibers, microparticles), 2D (films), and 3D (hydrogels, aerogels) materials. Due to its adaptable surface chemistry, high surface area, biocompatibility, and biodegradability, nanocellulose-based composite materials can be further transformed as drug delivery carriers. Herein, nanocellulose-based composite material used for drug delivery was reviewed. The typical drug release behaviors and the drug release mechanisms of nanocellulose-based composite materials were further summarized, and the potential application of nanocellulose-based composite materials was prospected as well.

Crosslinker-Free Hyaluronic Acid Aerogels

Aerogels based on hyaluronic acid (HA) were prepared without any chemical crosslinking by polymer dissolution, network formation via nonsolvent-induced phase separation, and supercritical CO₂ drying. The influence of solution pH, concentration of HA, and type of nonsolvent on network volume shrinkage, aerogel density, morphology, and specific surface area was investigated. A marked dependence of aerogel properties on solution pH was observed: aerogels with the highest specific surface area, 510 m²/g, and the lowest density, 0.057 g/cm³, were obtained when the HA solution was at its isoelectric point (pH 2.5). This work reports the first results ever on neat HA aerogels and constitutes the background for their use as advanced materials for biomedical applications.

Silica-Resorcinol-Melamine-Formaldehyde Composite Aerogels as High-Performance Thermal Insulators

Here, we report the gelation and supercritical drying of ethanol-based silica-resorcinol-melamine-formaldehyde (RMF) composite aerogels with relative concentrations of initial reagents ranging from neat silica to neat RMF alcogels. The as-prepared materials are subsequently supercritically dried with carbon dioxide. Their properties include a thermal conductivity in the 15-20 mW·m^-1·K^-1 range even with a silica content as low as 20%_wt. The possible reasons behind this interesting insulation performance and the mechanisms leading to the underlying gel structure are discussed in depth. A focus is made on the different gelation modes happening between the RMF and silica phases, from a coating of silica surfaces with RMF species to discontinuous RMF particles within a silica backbone and a continuous RMF backbone with isolated silica particles. The implications in terms of mechanical properties and thermal conductivity are elaborated upon. The initial ratio of silica-RMF species in this ethanol-based synthesis affects the micro- and macrostructure of the composites, resulting in materials with drastically different pore structures and thus an interesting array of possibilities for a new class of silica-organic composite aerogels, based on a sol-gel process.

Tuning bio-aerogel properties for controlling drug delivery. Part 2: Cellulose-pectin composite aerogels

The release of the model drug theophylline from cellulose-pectin composite aerogels was investigated. Cellulose and pectin formed an interpenetrated network, and the goal was to study and understand the influence of each component and its solubility in simulated gastric and intestinal fluids on the kinetics of release. Cellulose was dissolved, coagulated in water, followed by impregnation with pectin solution, crosslinking of pectin with calcium (in some cases this step was omitted), solvent exchange and supercritical CO₂ drying. Theophylline was loaded via impregnation and its release into simulated gastric fluid was monitored for 1 h followed by release into simulated intestinal fluid. The properties of the composite aerogels were varied via the cellulose and pectin concentrations as well as the calcium content in the precursor solutions. The release kinetics was correlated with aerogel specific surface area, bulk density as well as network swelling and erosion. The Korsmeyer-Peppas model was employed to identify the dominant release mechanisms during the various stages of the release.

Versatile Route for Multifunctional Aerogels Including Flaxseed Mucilage and Nanocrystals

Preparation of low density monolithic and free-standing organic-inorganic hybrid aerogels of various properties is demonstrated using green chemistry from a biosafe natural source (flaxseed mucilage) and freeze-casting and subsequent freeze drying. Bio-aerogels, luminescent aerogels and magneto-responsive aerogels were obtained by combination of the flaxseed mucilage with different types of nanoparticles. Moreover, the aerogels are investigated as possible drug release system using curcumin as a model. Various characterization techniques like thermogravimetric analysis, nitrogen physisorption, electron microscopy, UV/Vis absorption and emission spectroscopy, bulk density and mechanical measurements as well as in vitro release profile measurements are employed to investigate the obtained materials. The flaxseed-inspired organic-inorganic hybrid aerogels exhibit ultra-low densities of as low as 5.6 mg/cm³ for 0.5% (w/v) mucilage polymer, a specific surface area of 4 to 20 m² /g, high oil absorption capacity (23 g/g) and prominent compressibility. The natural biopolymer technique leads to low cost and biocompatible functional lightweight materials with tunable properties (physicochemical and mechanical) and significant potential for applications as supporting or stimuli responsive materials, carriers, reactors, microwave, and electromagnetic radiation protective (absorbing) material as well as in drug delivery and oil absorption. This article is protected by copyright. All rights reserved.

Development of Pectin-Based Aerogels with Several Excellent Properties for the Adsorption of Pb2

Traditional aerogels lack specific functional groups for the adsorption of Pb2+, which results in a low adsorption capacity and limits the application scope. Novel porous pectin-based aerogels (PPEAs) were prepared by incorporating polyethylenimine (PEI) using ethylene glycol diglycidyl ether (EGDE) as a cross-linker for the removal of Pb2+ from water. The cross-linking mechanism, morphology, mechanical strength, thermal stability, adsorption properties, and mechanism of the aerogels were investigated. The aerogels possessed several desirable features, such as a large maximum Pb2+ adsorption capacity (373.7 mg/g, tested at pH 5.0), ultralight (as low as 63.4 mg/cm3), high mechanical strength (stress above 0.24 MPa at 50% strain), and easy recyclability. Meanwhile, the equilibrium adsorption data was well described by the Langmuir-Freundlich (Sips) model and the kinetic adsorption process was well fitted using the pseudo-second-order model. The donor groups, such as -NH2, and oxygen-containing functional groups were responsible for the Pb2+ adsorption, which was confirmed by the FTIR and XPS analysis. The excellent characteristics mean that PPEAs are highly effective adsorbents in the remediation of lead-containing wastewater.

Deconstruction and Reassembly of Renewable Polymers and Biocolloids into Next Generation Structured Materials

This review considers the most recent developments in supramolecular and supraparticle structures obtained from natural, renewable biopolymers as well as their disassembly and reassembly into engineered materials. We introduce the main interactions that control bottom-up synthesis and top-down design at different length scales, highlighting the promise of natural biopolymers and associated building blocks. The latter have become main actors in the recent surge of the scientific and patent literature related to the subject. Such developments make prominent use of multicomponent and hierarchical polymeric assemblies and structures that contain polysaccharides (cellulose, chitin, and others), polyphenols (lignins, tannins), and proteins (soy, whey, silk, and other proteins). We offer a comprehensive discussion about the interactions that exist in their native architectures (including multicomponent and composite forms), the chemical modification of polysaccharides and their deconstruction into high axial aspect nanofibers and nanorods. We reflect on the availability and suitability of the latter types of building blocks to enable superstructures and colloidal associations. As far as processing, we describe the most relevant transitions, from the solution to the gel state and the routes that can be used to arrive to consolidated materials with prescribed properties. We highlight the implementation of supramolecular and superstructures in different technological fields that exploit the synergies exhibited by renewable polymers and biocolloids integrated in structured materials.

Tuning the Mechanical and Thermal Properties of Hydroxypropyl Methylcellulose Cryogels with the Aid of Surfactants

The mechanical and thermal properties of cryogels depend on their microstructure. In this study, the microstructure of hydroxypropyl methylcellulose (HPMC) cryogels was modified by the addition of ionic (bis (2-ethylhexyl) sodium sulfosuccinate, AOT) and non-ionic (Kolliphor^® EL) surfactants to the precursor hydrogels (30 g/L). The surfactant concentrations varied from 0.2 mmol/L to 3.0 mmol/L. All of the hydrogels presented viscous behavior (G″ > G′). Hydrogels containing AOT (c > 2.0 mmol/L) led to cryogels with the lowest compressive modulus (13 ± 1 kPa), the highest specific surface area (2.31 m²/g), the lowest thermal conductivity (0.030 W/(m·°C)), and less hygroscopic walls. The addition of Kolliphor^® EL to the hydrogels yielded the stiffest cryogels (320 ± 32 kPa) with the lowest specific surface area (1.11 m²/g) and the highest thermal conductivity (0.055 W/(m·°C)). Density functional theory (DFT) calculations indicated an interaction energy of −31.8 kcal/mol due to the interaction between the AOT sulfonate group and the HPMC hydroxyl group and the hydrogen bond between the AOT carbonyl group and the HPMC hydroxyl group. The interaction energy between the HPMC hydroxyl group and the Kolliphor^® EL hydroxyl group was calculated as −7.91 kcal/mol. A model was proposed to describe the effects of AOT or Kolliphor^® EL on the microstructures and the mechanical/thermal properties of HPMC cryogels.

Seaweed-Derived Alginate-Cellulose Nanofiber Aerogel for Insulation Applications

The next generation of green insulation materials is being developed to provide safer and more sustainable alternatives to conventional materials. Bio-based cellulose nanofiber (CNF) aerogels offer excellent thermal insulation properties; however, their high flammability restricts their application. In this study, the design concept for the development of a multifunctional and non-toxic insulation material is inspired by the natural composition of seaweed, comprising both alginate and cellulose. The approach includes three steps: first, CNFs were separated from alginate-rich seaweed to obtain a resource-efficient, fully bio-based, and inherently flame-retardant material; second, ice-templating, followed by freeze-drying, was employed to form an anisotropic aerogel for effective insulation; and finally, a simple crosslinking approach was applied to improve the flame-retardant behavior and stability. At a density of 0.015 g cm-3, the lightweight anisotropic aerogels displayed favorable mechanical properties, including a compressive modulus of 370 kPa, high thermal stability, low thermal conductivity (31.5 mW m-1 K-1), considerable flame retardancy (0.053 mm s-1), and self-extinguishing behavior, where the inherent characteristics were considerably improved by crosslinking. Different concentrations of the crosslinker altered the mechanical properties, while the anisotropic structure influenced the mechanical properties, combustion velocity, and to some extent thermal conductivity. Seaweed-derived aerogels possess intrinsic characteristics that could serve as a template for the future development of sustainable high-performance insulation materials.

Tuning bio-aerogel properties for controlling theophylline delivery. Part 1: Pectin aerogels

A comprehensive study of release kinetics of a hydrophilic drug from bio-aerogels based on pectin was performed. Pectin aerogels were made by polymer dissolution, gelation (in some cases this step was omitted), solvent exchange and drying with supercritical CO₂. Theophylline was loaded and its release was studied in the simulated gastric fluid during 1 h followed by the release in the simulated intestinal fluid. Pectin concentration, initial solution pH and concentration of calcium were varied to tune the properties of aerogel. The kinetics of theophylline release was monitored and correlated with aerogel density, specific surface area, and aerogel swelling and erosion. Various kinetic models were tested to identify the main physical mechanisms governing the release.

Polysaccharide-based aerogels for thermal insulation and superinsulation: An overview

To reduce energy losses due to the insufficient thermal insulation is one of the current "hot" topics. Various commercial porous materials are used with the best conductivity around 0.03-0.04 W/(m·K). Aerogels are the only known materials with "intrinsic" thermal superinsulating properties, i.e. with thermal conductivity below that of air in ambient conditions (0.025 W/(m·K)). The classical thermal superinsulating aerogels are based on silica and some synthetic polymers, with conductivity 0.014-0.018 W/(m·K). Aerogels based on natural polymers are new materials created at the beginning of the 21st century. Can bio-aerogels possess thermal superinsulating properties? What are the bottlenecks in the development of bio-aerogels as new high-performance thermal insulationing materials? We try to answer these questions by analyzing thermal conductivity of bio-aerogels reported in literature.

Recent Developments in Nanocellulose-Based Aerogels in Thermal Applications: A Review

Naturally derived nanocellulose (NC) is a renewable, biodegradable nanomaterial with high strength, low density, high surface area, and tunable surface chemistry, which allows its interaction with other polymers and nanomaterials in a controlled manner. In recent years, NC aerogel has gathered a lot of attention due to environmental concerns. This review presents recent developments of NC-based aerogels and their controlled interactions with other polymers and nanomaterials for thermal applications that include electronic devices, the apparel industry, superinsulating materials, and flame-retardant smart building materials. After going through the distinctive properties of NC aerogels, they are orderly categorized and discussed as thermally insulated, thermally conductive, and flame-retardant materials.

Hierarchically Organized Biomimetic Architectured Silk Fibroin-Ceramic-Based Anisotropic Hybrid Aerogels for Thermal Energy Management

Due to the current energy crises, the search for thermal energy management systems based on thermal insulating porous materials has drawn a significant deal of attention. Herein, we demonstrated the thermal insulation and management capabilities of cuttlefish bone mimetic aerogels with hierarchically organized porous structures directly fabricated from surface-modified and self-assembled silk fibroin (SF) biopolymer extracted from Bombyx mori silkworm cocoon biomass; hereafter, the materials developed referred to as X-AeroSF. Exploiting from creating an interpenetrating network of the secondary ceramic components of various one-, two-, and three-dimensional sepiolite (Mg₂H₂Si₃O₉·xH₂O), MXene (Ti₃C₂T_X), and silica nanostructures inside the self-assembled SF biopolymer and subsequent uni-directional freeze-casting and drying the resulted hydrogels, composites with aerogel features were obtained. The obtained aerogels possess low bulk density (ρ_b = 0.059-0.090 g cm^-3), low thermal conductivities (λ = 0.035-0.042 W m^-1 K^-1), and high thermal stability (up to ∼260 °C) with multi-modal lamella-bridge porous microstructures found in the cuttlefish bone structure. In addition, the intriguing anisotropy in the X-AeroSF composite porous structure enables thermal dissipation along with the aligned pore directions, thus decreasing the local overheating on the heated side. As a result, an improvement in thermal insulation in the perpendicular direction with respect to the pore lamellae was obtained. Therefore, the exquisite thermal energy management, biodegradability, low bulk density, fire resistivity, together with possible manufacture scalability of X-AeroSF composite, make this material attractive for future practical applications.

Nanocellulose-based foam morphological, mechanical and thermal properties in relation to hydrogel precursor structure and rheology

Foams were prepared from nanocellulose-based hydrogel precursors using a freeze-drying process. The work mainly aims at investigating the relationships between the mechanical and thermal properties of foams and the rheological properties of their hydrogel precursors, which were characterized in a previous paper. The structure of foams was characterized by SEM and confocal microscopy, their elasticity by compression tests, and their thermal conductivity by hot strip as well as transient pulsed techniques. A strong correlation was shown between the elastic properties of foams and those of their hydrogel precursors, and a minimum thermal conductivity was shown to appear at a cellulose volume fraction corresponding to a transition in viscoelastic properties of hydrogels. Results suggest that foams and hydrogels share common microstructural features, which makes it possible to tune the mechanical and thermal properties of foams by tuning the rheological properties of their hydrogel precursors.

Biorefinery Approach for Aerogels

According to the International Energy Agency, biorefinery is "the sustainable processing of biomass into a spectrum of marketable bio-based products (chemicals, materials) and bioenergy (fuels, power, heat)". In this review, we survey how the biorefinery approach can be applied to highly porous and nanostructured materials, namely aerogels. Historically, aerogels were first developed using inorganic matter. Subsequently, synthetic polymers were also employed. At the beginning of the 21st century, new aerogels were created based on biomass. Which sources of biomass can be used to make aerogels and how? This review answers these questions, paying special attention to bio-aerogels' environmental and biomedical applications. The article is a result of fruitful exchanges in the frame of the European project COST Action "CA 18125 AERoGELS: Advanced Engineering and Research of aeroGels for Environment and Life Sciences".

Chitosan-GPTMS-Silica Hybrid Mesoporous Aerogels for Bone Tissue Engineering

This study introduces a new synthesis route for obtaining homogeneous chitosan (CS)-silica hybrid aerogels with CS contents up to 10 wt%, using 3-glycidoxypropyl trimethoxysilane (GPTMS) as coupling agent, for tissue engineering applications. Aerogels were obtained using the sol-gel process followed by CO₂ supercritical drying, resulting in samples with bulk densities ranging from 0.17 g/cm³ to 0.38 g/cm³. The textural analysis by N₂-physisorption revealed an interconnected mesopore network with decreasing specific surface areas (1230-700 m²/g) and pore sizes (11.1-8.7 nm) by increasing GPTMS content (2-4 molar ratio GPTMS:CS monomer). In addition, samples exhibited extremely fast swelling by spontaneous capillary imbibition in PBS solution, presenting swelling capacities from 1.75 to 3.75. The formation of a covalent crosslinked hybrid structure was suggested by FTIR and confirmed by an increase of four hundred fold or more in the compressive strength up to 96 MPa. Instead, samples synthesized without GPTMS fractured at only 0.10-0.26 MPa, revealing a week structure consisted in interpenetrated polymer networks. The aerogels presented bioactivity in simulated body fluid (SBF), as confirmed by the in vitro formation of hydroxyapatite (HAp) layer with crystal size of approximately 2 µm size in diameter. In vitro studies revealed also non cytotoxic effect on HOB^® osteoblasts and also a mechanosensitive response. Additionally, control cells grown on glass developed scarce or no stress fibers, while cells grown on hybrid samples showed a significant (p < 0.05) increase in well-developed stress fibers and mature focal adhesion complexes.

Improving konjac glucomannan-based aerogels filtration properties by combining aerogel pieces in series with different pore size distributions

The pore size distribution of konjac glucomannan (KGM)-based aerogels seriously impacted the air filtration efficiency and filtration resistance. This study aimed to investigate the pore size distribution control of KGM-based aerogels through total solid concentration of the sol and to improve the filtration performance by preparing aerogel stacks, which were made by combining KGM-based aerogels with different pore size distribution (range: 0-180 μm). Results indicated that with increased total solid concentration from 50% to 100% of the origin formulae, aerogel pore size became smaller and the porosity was decreased for all the three sample formulae. Meanwhile, the aerogel mechanical property and filtration efficiency were both strengthened with increased total solid concentration, but the air resistance became significantly higher. The changing extent and rule were influenced by the sample components (KGM, starch, gelatin, wheat straw). The aerogel stacks prepared by in series combining the aerogel pieces with different pore size distribution (from large size to small size) was found to improve filtration efficiency (e.g. from 70% to 80% for K1G2S4WS2) and significantly lower the air resistance (e.g. from 270 Pa to 190 Pa for K1G2S4WS2). This study could guide the filtration performance improvement of aerogels.

Solvents, CO2 and biopolymers: Structure formation in chitosan aerogel

The functionality of biopolymer aerogels is inherently linked to its microstructure, which in turn depends on the synthesis protocol. Detailed investigations on the macroscopic size change and nanostructure formation during chitosan aerogel synthesis reveal a new aspect of biopolymer aerogels that increases process flexibility. Formaldehyde-cross-linked chitosan gels retain a significant fraction of their original volume after solvent exchange into methanol (50.3 %), ethanol (47.1 %) or isopropanol (26.7 %), but shrink dramatically during subsequent supercritical CO₂ processing (down to 4.9 %, 3.5 % and 3.7 %, respectively). In contrast, chitosan gels shrink more strongly upon exchange into n-heptane (7.2 %), a low affinity solvent, and retain this volume during CO₂ processing. Small-angle X-ray scattering confirms that the occurrence of the volumetric changes correlates with mesoporous network formation through physical coagulation in CO₂ or n-heptane. The structure formation step can be controlled by solvent-polymer and polymer-drying interactions, which would be a new tool to tailor the aerogel structure.

Biobased Cryogels from Enzymatically Oxidized Starch: Functionalized Materials as Carriers of Active Molecules

Starch recovered from an agrifood waste, pea pods, was enzymatically modified and used to prepare cryogels applied as drug carriers. The enzymatic modification of starch was performed using the laccase/(2,2,6,6-tetramethylpiperidin-1-yl)oxyl TEMPO system, at a variable molar ratio. The characterization of the ensuing starches by solution NMR spectroscopy showed partial conversion of the primary hydroxyl groups versus aldehyde and carboxyl groups and successive creation of hemiacetal and ester bonds. Enzymatically modified starch after simple freezing and lyophilization process provided stable and compact cryogels with a morphology characterized by irregular pores, as determined by atomic force (AFM) and scanning electron microscopy (SEM). The application of cryogels as carriers of active molecules was successfully evaluated by following two different approaches of loading with drugs: a) as loaded sponge, by adsorption of drug from the liquid phase; and b) as dry-loaded cryogel, from a dehydration step added to loaded cryogel from route (a). The efficiency of the two routes was studied and compared by determining the drug release profile by proton NMR studies over time. Preliminary results demonstrated that cryogels from modified starch are good candidates to act as drug delivery systems due to their stability and prolonged residence times of loaded molecules, opening promising applications in biomedical and food packaging scenarios.

New Trends in Bio-Based Aerogels

(1) Background: The fascinating properties of currently synthesized aerogels associated with the flexible approach of sol-gel chemistry play an important role in the emergence of special biomedical applications. Although it is increasingly known and mentioned, the potential of aerogels in the medical field is not sufficiently explored. Interest in aerogels has increased greatly in recent decades due to their special properties, such as high surface area, excellent thermal and acoustic properties, low density and thermal conductivity, high porosity, flame resistance and humidity, and low refractive index and dielectric constant. On the other hand, high manufacturing costs and poor mechanical strength limit the growth of the market. (2) Results: In this paper, we analyze more than 180 articles from recent literature studies focused on the dynamics of aerogels research to summarize the technologies used in manufacturing and the properties of materials based on natural polymers from renewable sources. Biomedical applications of these bio-based materials are also introduced. (3) Conclusions: Due to their complementary functionalities (bioactivity, biocompatibility, biodegradability, and unique chemistry), bio-based materials provide a vast capability for utilization in the field of interdisciplinary and multidisciplinary scientific research.

Strong, Machinable, and Insulating Chitosan-Urea Aerogels: Toward Ambient Pressure Drying of Biopolymer Aerogel Monoliths

Biopolymer aerogels are an emerging class of materials with potential applications in drug delivery, thermal insulation, separation, and filtration. Chitosan is of particular interest as a sustainable, biocompatible, and abundant raw material. Here, we present urea-modified chitosan aerogels with a high surface area and excellent thermal and mechanical properties. The irreversible gelation of an acidic chitosan solution is triggered by the thermal decomposition of urea at 80 °C through an increase in pH and, more importantly, the formation of abundant ureido terminal groups. The hydrogels are dried using either supercritical CO₂ drying (SCD) or ambient pressure drying (APD) methods to elucidate the influence of the drying process on the final aerogel properties. The hydrogels are exchanged into ethanol prior to SCD, and into ethanol and then heptane prior to APD. The surface chemistry and microstructure are monitored by solid-state NMR and Fourier transform infrared spectroscopy, scanning electron microscopy, and nitrogen sorption. Surprisingly, large monolithic aerogel plates (70 × 70 mm²) can be produced by APD, albeit at a somewhat higher density (0.17-0.42 g/cm³). The as prepared aerogels have thermal conductivities of ∼24 and ∼31 mW/(m·K) and surface areas of 160-170 and 85-230 m²/g, for SCD and APD, respectively. For a primarily biopolymer-based material, these aerogels are exceptionally stable at elevated temperature (TGA) and char and self-extinguish after direct flame exposure. The urea-modified chitosan aerogels display superior mechanical properties compared to traditional silica aerogels, with no brittle rupture up to at least 80% strain, and depending on the chitosan concentration, relatively high E-moduli (1.0-11.6 MPa), and stress at 80% strain values (σ₈₀ of 3.5-17.9 MPa). Remarkably, the aerogel monoliths can be shaped and machined with standard tools, for example, drilling and sawing. This first demonstration to produce monolithic and machinable, mesoporous aerogels from bio-sourced, renewable, and nontoxic precursors, combined with the potential for reduced production cost by means of simple APD, opens up new opportunities for biopolymer aerogel applications and marks an important step toward commercialization of biopolymer aerogels.

Production of starch aerogel in form of monoliths and microparticles

Pea and amylomaize starches were used to produce aerogel in form of monoliths and microparticles. The formation of starch gel was investigated, and we showed that each starch needed a different pasting temperature for its complete dissolution. The gelation kinetics was investigated with oscillatory rheometry for both systems as a function of the starch concentration. The gelation and retrogradation temperature of the starch gel were varied and its impact on the final aerogel evaluated. The emulsion gelation was carried out batch wise in a stirred vessel with different impeller geometries, concentrations of surfactant (Span80 and PGPR) and stirring rates. A particle size prediction approach based on idealized flow (Couette, 2D hyperbolic and turbulent) during the emulsification was proposed. A semi-continuous set-up for the emulsion gelation was developed in which the emulsification occurs in a single pass through a colloid mill and the gelation is triggered in-line with a counter-current heat exchanger.