Tailored freestanding multilayered membranes based on chitosan and alginate

Tailored diffusion limiting membrane for microneedle glucose sensors with wide linear range

Continuous glucose monitoring is very important to daily blood glucose control in diabetic patients, but its accuracy is limited by the narrow linear range of the response of biosensor to the glucose concentration because of the oxygen starvation in tissue and the limited maximum conversion rate of glucose oxidase. In this work, a biocompatible diffusion limiting membrane based on two medical-grade polyurethanes is developed via blending modification to restrict the diffusion flux of glucose to match the oxygen concentration and the maximum conversion rate. The expansiveness of the linear range for the nanomaterials-modified electrode in the glucose biosensor can be achieved through the regulation of two polyurethanes, the solvent, and the thickness of the membrane. In addition, the mass transport of hydrogen peroxide and interfering substances is also limited of the membrane. The in vitro experiments demonstrated that the membrane-modified microneedle biosensor exhibited a rapid response to the concentration variation of glucose, a wide linear range that is sufficient to cover the blood concentration of healthy and diabetic people, the ability to resist the oxygen concentration fluctuation and interfering substances, good reproducibility and long-term stability. The custom wearable electrochemical system, possessing these characteristics, has been proven to accurately monitor the blood concentration in a living rat in real time. This demonstrates a significant potential for application in both daily and clinical blood glucose monitoring.

Recent Developments in Layer-by-Layer Assembly for Drug Delivery and Tissue Engineering Applications

Surfaces with biological functionalities are of great interest for biomaterials, tissue engineering, biophysics, and for controlling biological processes. The layer-by-layer (LbL) assembly is a highly versatile methodology introduced 30 years ago, which consists of assembling complementary polyelectrolytes or biomolecules in a stepwise manner to form thin self-assembled films. In view of its simplicity, compatibility with biological molecules, and adaptability to any kind of supporting material carrier, this technology has undergone major developments over the past decades. Specific applications have emerged in different biomedical fields owing to the possibility to load or immobilize biomolecules with preserved bioactivity, to use an extremely broad range of biomolecules and supporting carriers, and to modify the film's mechanical properties via crosslinking. In this review, the focus is on the recent developments regarding LbL films formed as 2D or 3D objects for applications in drug delivery and tissue engineering. Possible applications in the fields of vaccinology, 3D biomimetic tissue models, as well as bone and cardiovascular tissue engineering are highlighted. In addition, the most recent technological developments in the field of film construction, such as high-content liquid handling or machine learning, which are expected to open new perspectives in the future developments of LbL, are presented.

Chemical and Structural Engineering of Gelatin-Based Delivery Systems for Therapeutic Applications: A Review

As a biodegradable and biocompatible protein derived from collagen, gelatin has been extensively exploited as a fundamental component of biological scaffolds and drug delivery systems for precise medicine. The easily engineered gelatin holds great promise in formulating various delivery systems to protect and enhance the efficacy of drugs for improving the safety and effectiveness of numerous pharmaceuticals. The remarkable biocompatibility and adjustable mechanical properties of gelatin permit the construction of active 3D scaffolds to accelerate the regeneration of injured tissues and organs. In this Review, we delve into diverse strategies for fabricating and functionalizing gelatin-based structures, which are applicable to gene and drug delivery as well as tissue engineering. We emphasized the advantages of various gelatin derivatives, including methacryloyl gelatin, polyethylene glycol-modified gelatin, thiolated gelatin, and alendronate-modified gelatin. These derivatives exhibit excellent physicochemical and biological properties, allowing the fabrication of tailor-made structures for biomedical applications. Additionally, we explored the latest developments in the modulation of their physicochemical properties by combining additive materials and manufacturing platforms, outlining the design of multifunctional gelatin-based micro-, nano-, and macrostructures. While discussing the current limitations, we also addressed the challenges that need to be overcome for clinical translation, including high manufacturing costs, limited application scenarios, and potential immunogenicity. This Review provides insight into how the structural and chemical engineering of gelatin can be leveraged to pave the way for significant advancements in biomedical applications and the improvement of patient outcomes.

Effect of high cyclic hydrostatic pressure on osteogenesis of mesenchymal stem cells cultured in liquefied micro-compartments

Bone resident cells are constantly subjected to a range of distinct mechanical loadings, which generates a complex microenvironment. In particular, hydrostatic pressure (HP) has a key impact on modulation of cell function and fate determination. Although HP is a constant mechanical stimulus, its role in regulating the osteogenesis process within a defined 3D microenvironment has not been comprehensively elucidated. Perceiving how environmental factors regulate the differentiation of stem cells is essential for expanding their regenerative potential. Inspired by the mechanical environment of bone, this study attempted to investigate the influence of different ranges of cyclic HP on human adipose-derived mesenchymal stem cells (MSCs) encapsulated within a compartmentalized liquefied microenvironment. Taking advantage of the liquefied environment of microcapsules, MSCs were exposed to cyclic HP of 5 or 50 MPa, 3 times/week at 37 °C. Biological tests using fluorescence staining of F-actin filaments showed a noticeable improvement in cell-cell interactions and cellular network formation of MSCs. These observations were more pronounced in osteogenic (OST) condition, as confirmed by fluorescent staining of vinculin. More interestingly, there was a significant increase in alkaline phosphatase activity of MSCs exposed to 50 MPa magnitude of HP, even in the absence of osteoinductive factors. In addition, a greater staining area of both osteopontin and hydroxyapatite was detected in the 50 MPa/OST group. These findings highlight the benefit of hydrostatic pressure to regulate osteogenesis of MSCs as well as the importance of employing simultaneous biochemical and mechanical stimulation to accelerate the osteogenic potential of MSCs for biomedical purposes.

Marine-origin polysaccharides-based free-standing multilayered membranes as sustainable nanoreservoirs for controlled drug delivery

The layer-by-layer (LbL) assembly technology has been widely used to functionalise surfaces and precisely engineer robust multilayered bioarchitectures with tunable structures, compositions, properties, and functions at the nanoscale by resorting to a myriad of building blocks exhibiting complementary interactions. Among them, marine-origin polysaccharides are a sustainable renewable resource for the fabrication of nanostructured biomaterials for biomedical applications owing to their wide bioavailability, biocompatibility, biodegradability, non-cytotoxicity, and non-immunogenic properties. Chitosan (CHT) and alginate (ALG) have been widely employed as LbL ingredients to shape a wide repertoire of size- and shape-tunable electrostatic-driven multilayered assemblies by exploring their opposite charge nature. However, the insolubility of CHT in physiological conditions intrinsically limits the range of bioapplications of the as-developed CHT-based LbL structures. Herein, we report the preparation of free-standing (FS) multilayered membranes made of water-soluble quaternised CHT and ALG biopolymers for controlled release of model drug molecules. The influence of the film structure in the drug release rate is studied by assembling two distinct set-ups of FS membranes, having the model hydrophilic drug fluorescein isothiocyanate-labelled bovine serum albumin (FITC-BSA) either as an intrinsic building block or added as an outer layer after the LbL assembly process. Both FS membranes are characterised for their thickness, morphology, in vitro cytocompatibility, and release profile, with those having FITC-BSA as an intrinsic LbL ingredient denoting a more sustained release rate. This work opens up new avenues for the design and development of a wide array of CHT-based devices for biomedical applications, overcoming the limitations associated with the insolubility of native CHT under physiological conditions.

Building Fucoidan/Agarose-Based Hydrogels as a Platform for the Development of Therapeutic Approaches against Diabetes

Current management for diabetes has stimulated the development of versatile 3D-based hydrogels as in vitro platforms for insulin release and as support for the encapsulation of pancreatic cells and islets of Langerhans. This work aimed to create agarose/fucoidan hydrogels to encapsulate pancreatic cells as a potential biomaterial for diabetes therapeutics. The hydrogels were produced by combining fucoidan (Fu) and agarose (Aga), marine polysaccharides derived from the cell wall of brown and red seaweeds, respectively, and a thermal gelation process. The agarose/fucoidan (AgaFu) blended hydrogels were obtained by dissolving Aga in 3 or 5 wt % Fu aqueous solutions to obtain different proportions (4:10; 5:10, and 7:10 wt). The rheological tests on hydrogels revealed a non-Newtonian and viscoelastic behavior, while the characterization confirmed the presence of the two polymers in the structure of the hydrogels. In addition, the mechanical behavior showed that increasing Aga concentrations resulted in hydrogels with higher Young's modulus. Further, the ability of the developed materials to sustain the viability of human pancreatic cells was assessed by encapsulation of the 1.1B4HP cell line for up to 7 days. The biological assessment of the hydrogels revealed that cultured pancreatic beta cells tended to self-organize and form pseudo-islets during the period studied.

Alginate-Chitosan Membranes for the Encapsulation of Lavender Essential Oil and Development of Biomedical Applications Related to Wound Healing

Biopolymers such as chitosan (CHT) or alginate (ALG) are among the most prominent for health-related applications due to their broad bioactivity. Their combination for the preparation of membranes is hereby proposed as an application for wound healing with the incorporation of lavender essential oil (LEO), widely known for its antioxidant and antimicrobial properties. The preparation of CHT, CHT + LEO, ALG, ALG + LEO, and CHT/ALG + LEO membranes was accomplished, and its composition was analyzed using Fourier Transform Infrared Spectroscopy (FTIR). The water absorption capacity and oil release profile of the membranes revealed higher water uptake capacity when a lower LEO release was obtained. The combined CHT/ALG + LEO film showed a water uptake percentage of 638% after 48 h and a maximum LEO release concentration of 42 mg/L. Cytotoxicity and biocompatibility of the prepared membranes were studied using a HaCaT cell line, with an assessment of cell viability regarding film leachables, DNA quantification, and DAPI-phalloidin staining. The results revealed that the indirect contact of the prepared membranes via its leachables does not compromise cell viability, and upon direct contact, cells do not adhere or proliferate on the surface of the membranes. Moreover, the CHT/ALG + LEO membrane increases cell proliferation, making it suitable for applications in wound healing.

Influence of Ionic Strength and Specific Ion Effects on Polyelectrolyte Multilayer Films with pH-Responsive Behavior

Layer-by-layer assembled multilayer films have shown great potential for different applications owing to their responsive behavior. Herein, we systematically investigated the effects of composition, salt concentration, and ion specificity on the pH responsiveness of covalently crosslinked chitosan and alginate dialdehyde multilayer films. The changes in film swelling were measured using ellipsometry from low (0.01 mM) to high (3 M) salt (NaCl or NaSCN) concentrations at pH 3, 6, and 9. The swelling responses to increasing ionic strength matched the swelling responses observed for polyzwitterionic and weak monocomponent polyelectrolyte films and depended on the multilayer composition, pH, and ion specificity. Finally, we used the ellipsometric data to demonstrate that the pH responsiveness of such multilayer films, as measured using a quartz crystal microbalance with dissipation monitoring, strongly depends on the ionic condition under which the responses were measured. We thus show that erroneous conclusions about the pH responsiveness of polyelectrolyte multilayer films can be easily obtained if the ionic environment of the application does not closely resemble the ionic condition under which the pH responsiveness is tested.

Programmable Physical Properties of Freestanding Chitosan Membranes Electrofabricated in Microfluidics

Microfluidic-integrated freestanding membranes with suitable biocompatibility and tunable physicochemical properties are in high demand for a wide range of life science and biological studies. However, there is a lack of facile and rapid methods to integrate such versatile membranes into microfluidics. A recently invented interfacial electrofabrication of chitosan membranes offers an in-situ membrane integration strategy that is flexible, controllable, simple, and biologically friendly. In this follow-up study, we explored the ability to program the physical properties of these chitosan membranes by varying the electrofabrication conditions (e.g., applied voltage and pH of alginate). We found a strong association between membrane growth rate, properties, and fabrication parameters: high electrical stimuli and pH of alginate resulted in high optical retardance and low permeability, and vice versa. This suggests that the molecular alignment and density of electrofabricated chitosan membranes could be actively tailored according to application needs. Lastly, we demonstrated that this interfacial electrofabrication could easily be expanded to produce chitosan membrane arrays with higher uniformity than the previously well-established flow assembly method. This study demonstrates the tunability of the electrofabricated membranes' properties and functionality, thus expanding the utility of such membranes for broader applications in the future.

Chitosan-Based Biomaterials: Insights into Chemistry, Properties, Devices, and Their Biomedical Applications

Chitosan is a marine-origin polysaccharide obtained from the deacetylation of chitin, the main component of crustaceans’ exoskeleton, and the second most abundant in nature. Although this biopolymer has received limited attention for several decades right after its discovery, since the new millennium chitosan has emerged owing to its physicochemical, structural and biological properties, multifunctionalities and applications in several sectors. This review aims at providing an overview of chitosan properties, chemical functionalization, and the innovative biomaterials obtained thereof. Firstly, the chemical functionalization of chitosan backbone in the amino and hydroxyl groups will be addressed. Then, the review will focus on the bottom-up strategies to process a wide array of chitosan-based biomaterials. In particular, the preparation of chitosan-based hydrogels, organic–inorganic hybrids, layer-by-layer assemblies, (bio)inks and their use in the biomedical field will be covered aiming to elucidate and inspire the community to keep on exploring the unique features and properties imparted by chitosan to develop advanced biomedical devices. Given the wide body of literature that has appeared in past years, this review is far from being exhaustive. Selected works in the last 10 years will be considered.

Green approaches for extraction, chemical modification and processing of marine polysaccharides for biomedical applications

Over the past few decades, natural-origin polysaccharides have received increasing attention across different fields of application, including biomedicine and biotechnology, because of their specific physicochemical and biological properties that have afforded the fabrication of a plethora of multifunctional devices for healthcare applications. More recently, marine raw materials from fisheries and aquaculture have emerged as a highly sustainable approach to convert marine biomass into added-value polysaccharides for human benefit. Nowadays, significant efforts have been made to combine such circular bio-based approach with cost-effective and environmentally-friendly technologies that enable the isolation of marine-origin polysaccharides up to the final construction of a biomedical device, thus developing an entirely sustainable pipeline. In this regard, the present review intends to provide an up-to-date outlook on the current green extraction methodologies of marine-origin polysaccharides and their molecular engineering toolbox for designing a multitude of biomaterial platforms for healthcare. Furthermore, we discuss how to foster circular bio-based approaches to pursue the further development of added-value biomedical devices, while preserving the marine ecosystem.

Adhesive Bioinspired Coating for Enhancing Glass-Ceramics Scaffolds Bioactivity

Bioceramic scaffolds, composed of a biphasic composite containing bioactive glass and hydroxyapatite, were prepared in this work to overcome the intrinsic limits of the two components taken separately (in particular, their specific reactivities and dissolution rates, which should be tunable as a function of the given clinical requirements). To mimic the biological environment and tune the different stages of cellular response, a coating with gelatin and chondroitin sulphate via Layer-by-Layer (LbL) assembly was presented and discussed. The resulting functionalized scaffolds were affected by the coating in terms of microstructure and porosity. In addition, the LbL coating significantly enhanced the seeded cell behaviour, with high adhesion, proliferation and osteogenic activity, as revealed by the alkaline phosphatase activity and overexpression of osteopontin and osteocalcin.

Free-standing multilayer films as growth factor reservoirs for future wound dressing applications

Chronic skin wounds place a high burden on patients and health care systems. The use of angiogenic and mitogenic growth factors can facilitate the healing but growth factors are quickly inactivated by the wound environment if added exogenously. Here, free-standing multilayer films (FSF) are fabricated from chitosan and alginate as opposing polyelectrolytes in an alternating manner using layer-by-layer technique. One hundred bilayers form an about 450 μm thick, detachable free-standing film that is subsequently crosslinked by either ethyl (dimethylaminopropyl) carbodiimide combined with N-hydroxysuccinimide (E-FSF) or genipin (G-FSF). The characterization of swelling, oxygen permeability and crosslinking density shows reduced swelling and oxygen permeability for both crosslinked films compared to non-crosslinked films (N-FSF). Loading of fibroblast growth factor 2 (FGF2) into the films results in a sustained release from crosslinked FSF in comparison to non-crosslinked FSF. Biocompatibility studies in vitro with human dermal fibroblasts cultured underneath the films demonstrate increased cell growth and cell migration for all films with and without FGF2. Especially G-FSF loaded with FGF2 greatly increases cell proliferation and migration. In vivo biocompatibility studies by subcutaneous implantation in mice show that E-FSF causes an inflammatory tissue response that is absent in the case of G-FSF. N-FSF also represents a biocompatible film but shows early degradation. All FSF possess antibacterial properties against gram+ and gram- bacteria demonstrated by an agar diffusion disc assay. In summary, FSF made of alginate and chitosan crosslinked with genipin can act as a reservoir for the sustained release of FGF2, possessing high biocompatibility in vitro and in vivo. Moreover, G-FSF promotes growth and migration of human dermal fibroblasts and has antibacterial properties, which makes it an interesting candidate for bioactive wound.

Engineering of Stable Cross-Linked Multilayers Based on Thermo-Responsive PNIPAM-Grafted-Chitosan/Heparin to Tailor Their Physiochemical Properties and Biocompatibility

The thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) is ubiquitously applied in controlled drug release and tissue engineering. However, the lack of bioactivity of PNIPAM restricts its use in cell-containing systems being a thermo-responsive adhesive substratum with no regulating effect on cell growth and differentiation. In this study, integrating PNIPAM with chitosan into PNIPAM-grafted-chitosan (PNIPAM-Chi) allows a layer-by-layer assembly with bioactive heparin to fabricate PNIPAM-modified polyelectrolyte multilayers (PNIPAM-PEMs). Grafting PNIPAM chains of either 2 (LMW) or 10 kDa (HMW) on the chitosan backbone influences the cloud point (CP) temperature in the range from 31 to 33 °C. PNIPAM-Chi with either a higher molecular weight or a higher degree of substitution of PNIPAM chains exhibiting a significant increase in diameter above CP as ensured by dynamic light scattering is selected to fabricate PEM with heparin as a polyanion at pH 4. Little difference of layer growth is detected between the chosen PNIPAM-Chi used as polycations by surface plasmon resonance, while multilayers formed with HMW-0.02 are more hydrated and show striking swelling-and-shrinking abilities when studied with quartz crystal microbalance with dissipation monitoring. Subsequently, the multilayers are covalently cross-linked using 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/N-hydroxysuccinimide to strengthen the stability of the systems under physiological conditions. Ellipsometry results confirm the layer integrity after exposure to the physiological buffer at pH 7.4 compared to those without cross-linking. Moreover, significantly higher adhesion and more spreading of C3H10T1/2 multipotent embryonic mouse fibroblasts on cross-linked PEMs, particularly with heparin terminal layers, are observed owing to the bioactivity of heparin. The slightly more hydrophobic surfaces of cross-linked PNIPAM-PEMs at 37 °C also increase cell attachment and growth. Thus, layer-by-layer constructed PNIPAM-PEM with cross-linking represents an interesting cell culture system that can be potentially employed for thermally uploading and controlled release of growth factors that further promotes tissue regeneration.

Selective terpene based therapeutic deep eutectic systems against colorectal cancer

Cancer remains a major health problem worldwide, with colorectal cancer (CRC) being the third most incident and the second most lethal. Inflammation, on the other hand, has been highly associated with cancer development and maintenance, therefore, the reduction of the inflammatory microenvironment represents a promising therapeutic strategy. Deep eutectic systems (DES) are based on the combination of different components which together, at a certain molar ratio, present a deep decrease in their melting point compared with the individual compounds. When an active pharmaceutical ingredient is part of a DES it is designated by therapeutic deep eutectic system (THEDES). New THEDES combining terpenes with anticancer properties, such as safranal, menthol and linalool, with nonsteroidal anti-inflammatory drugs (NSAIDs), like ibuprofen, ketoprofen and flurbiprofen were produced. To evaluate THEDES anti-CRC therapeutic potential, their physico-chemical properties, bioavailability and bioactivity, were explored. Our results show that safranal:ibuprofen (3:1), safranal:ibuprofen (4:1) and menthol:ibuprofen (3:1) present promising therapeutic activity towards CRC cells due to a selective cytotoxic action towards cancer cells. menthol:ibuprofen (3:1) anti-proliferative action seems to be related with cell membrane disruption, reduction of the inflammation through the reduction of reactive oxygen species (ROS) production, and induction of apoptosis via caspase-3. On the other hand, safranal:ibuprofen (3:1) and safafranal:ibuprofen (4:1) seem to prevent tumour expansion only through the induction of apoptosis via caspase-3. Besides, these systems present an increase in ibuprofen permeability, with menthol:ibuprofen (3:1) increasing also ibuprofen's solubility thus its overall bioavailability. Knowing that cancer is a huge problematic situation that requires alternative therapies with less side effects, improved efficacy, associated with less costs and environmentally friendly, a new opportunity emerges for DES to be part of the pharmaceutical industry.

Marine Polysaccharides for Wound Dressings Application: An Overview

Wound dressings have become a crucial treatment for wound healing due to their convenience, low cost, and prolonged wound management. As cutting-edge biomaterials, marine polysaccharides are divided from most marine organisms. It possesses various bioactivities, which allowing them to be processed into various forms of wound dressings. Therefore, a comprehensive understanding of the application of marine polysaccharides in wound dressings is particularly important for the studies of wound therapy. In this review, we first introduce the wound healing process and describe the characteristics of modern commonly used dressings. Then, the properties of various marine polysaccharides and their application in wound dressing development are outlined. Finally, strategies for developing and enhancing marine polysaccharide wound dressings are described, and an outlook of these dressings is given. The diverse bioactivities of marine polysaccharides including antibacterial, anti-inflammatory, haemostatic properties, etc., providing excellent wound management and accelerate wound healing. Meanwhile, these biomaterials have higher biocompatibility and biodegradability compared to synthetic ones. On the other hand, marine polysaccharides can be combined with copolymers and active substances to prepare various forms of dressings. Among them, emerging types of dressings such as nanofibers, smart hydrogels and injectable hydrogels are at the research frontier of their development. Therefore, marine polysaccharides are essential materials in wound dressings fabrication and have a promising future.

Recent progress in materials development and biological properties of GTR membranes for periodontal regeneration

Chronic periodontal is a very common infection that instigates the destruction of oral tissue, and for its treatment, it is necessary to minimize the infection and the defects regeneration. Periodontium consists of four types of tissues: (a) cementum, (b) periodontal ligament, (c) gingiva, and 4) alveolar bone. In separated cavities, regenerative process also allows various cell proliferations. Guided tissue regeneration (GTR) is a potential procedure that favors periodontal regrowth; however, some limitations (such as ineffective hemostatic property, poor mechanical property, and improper biodegradation) are also associated with it. This review mainly emphasizes on the following areas: (a) a summarized overview of the periodontium and its immunological situations, (b) recently utilized treatments for regeneration of distinctive periodontal tissues; (c) an overview of GTR membranes available commercially, and the latest developments on the characterization and processing of GTR membrane material; and 4) the function of the different non-polymeric/polymeric materials, which are acting as drug carriers, antibacterial agents, nanoparticles, and periodontal barrier membranes to prevent periodontal inflammation and to improve the strength of the GTR membrane.

Polyelectrolyte Multilayer Films Based on Natural Polymers: From Fundamentals to Bio-Applications

Natural polymers are of great interest in the biomedical field due to their intrinsic properties such as biodegradability, biocompatibility, and non-toxicity. Layer-by-layer (LbL) assembly of natural polymers is a versatile, simple, efficient, reproducible, and flexible bottom-up technique for the development of nanostructured materials in a controlled manner. The multiple morphological and structural advantages of LbL compared to traditional coating methods (i.e., precise control over the thickness and compositions at the nanoscale, simplicity, versatility, suitability, and flexibility to coat surfaces with irregular shapes and sizes), make LbL one of the most useful techniques for building up advanced multilayer polymer structures for application in several fields, e.g., biomedicine, energy, and optics. This review article collects the main advances concerning multilayer assembly of natural polymers employing the most used LbL techniques (i.e., dipping, spray, and spin coating) leading to multilayer polymer structures and the influence of several variables (i.e., pH, molar mass, and method of preparation) in this LbL assembly process. Finally, the employment of these multilayer biopolymer films as platforms for tissue engineering, drug delivery, and thermal therapies will be discussed.

Angiogenic potential of airbrushed fucoidan/polycaprolactone nanofibrous meshes

Implantation of biomaterials and hybrid constructs in tissue engineering approaches presents major limitations such as inflammatory reaction and the lack of vasculature integration. Therefore, new strategies are needed to enhance implant function, immune protection, and revascularization. In this work, we developed fibrous meshes composed of fucoidan (Fu), a sulfated polysaccharide extracted from brown algae, and polycaprolactone (PCL), a synthetic biodegradable polymer, using the airbrush technique. The chemical characterization by FTIR, EDS, and XPS confirmed the presence of the two polymers in the structure of airbrushed nanofibrous meshes (ANFM). Moreover, these nanofibrous exhibited good wettability and mechanical properties envisaging their application as templates for biomaterials and cell culture. The developed ANFM were directly cultured with human pulmonary microvascular endothelial (HPMEC-ST1.6R) cells for up to 7 days. Biological results demonstrated that ANFM comprising Fu promoted cellular attachment, spreading, and proliferation of human endothelial cells. The angiogenic potential of ANFM was further evaluated by onplantation of PCL and PCL/Fu ANFM in chick chorioallantoic membrane (CAM). In ovo and ex ovo results showed that the incorporation of Fu increased the pro-angiogenic potential of ANFM. Altogether, the results suggest that airbrush biocomposite meshes could be used as a biomaterial substrate to promote vascularization.

Chitosan-based smart hybrid materials: a physico-chemical perspective

Chitosan is one of the most studied cationic polysaccharides. Due to its unique characteristics of being water soluble, biocompatible, biodegradable, and non-toxic, this macromolecule is highly attractive for a broad range of applications. In addition, its complex behavior and the number of ways it interacts with different components in a system result in an astonishing variety of chitosan-based materials. Herein, we present recent advances in the field of chitosan-based materials from a physico-chemical perspective, with focus on aqueous mixtures with oppositely charged colloids, chitosan-based thin films, and nanocomposite systems. In this review, we focus our attention on the physico-chemical properties of chitosan-based materials, including solubility, mechanical resistance, barrier properties, and thermal behaviour, and provide a link to the chemical peculiarities of chitosan, such as its intrinsic low solubility, high rigidity, large charge separation, and strong tendency to form intra- and inter-molecular hydrogen bonds.

Improvement of New Dianionic Ionic Liquids vs Monoanionic in Solubility of Poorly Water-Soluble Drugs

New ionic liquids (ILs) based on dianionic phosphonate anions and ammonium cations were prepared and characterized. They were used as excipients to increase the water solubility of two oral drugs, piroxicam and ibuprofen, that are slightly soluble in water. An increment in solubility of 300-fold was achieved for ibuprofen when compared with pure water, with only 0.25 mol% of IL in water. Interestingly, this was achieved with the less toxic dianionic ionic liquid [N_{4 1 2OH 2OH}]₂ [C₂H₅PO₃], which presents an IC₅₀ of 120 mM (≈0.25 mol%). On the other hand, piroxicam showed an increase of 480-fold for the same dianionic ionic liquid, with the same ionic liquid percentage. In contrast, for monoanionic ionic liquids, the effect was not so pronounced, and only a 10-fold was obtained, in the presence of 0.3 mol% of IL. The lipophilicity (logP) of drugs decreased in the presence of these ILs. Cytotoxicity profile of these ILs was determined and they did not show a significant impact towards healthy fibroblasts. The cytotoxicity of ibuprofen and piroxicam was also determined, and cellular viability almost did not change when ionic liquid was in the presence of 1 mM of oral drug.

Organic Salts Based on Isoniazid Drug: Synthesis, Bioavailability and Cytotoxicity Studies

Tuberculosis is one of the ten causes of morbidity and mortality worldwide caused by Mycobacterium tuberculosis complex. Some of the anti-tuberculosis drugs used in clinic studies, despite being effective for the treatment of tuberculosis, present serious adverse effects as well as poor bioavailability, stability, and drug-resistance problems. Thus, it is important to develop approaches that could provide shorter drug regimens, preventing drug resistance, toxicity of the antibiotics, and improve their bioavailability. Herein, we reported the use of organic salts based on the isoniazid drug, which can act as an organic cation combined with suitable organic anions such as alkylsulfonate-based (mesylate, R or S-Camphorsulfonate), carboxylate-based (glycolate, vanylate) and sacharinate. The synthesis, characterization, and cytotoxicity studies comparing with the original isoniazid drug have been performed. The possibility to explore dicationic salts seems promising in order to improve original bioavailability, and promote the elimination of polymorphic forms as well as higher stability, which are relevant characteristics that the pharmaceutical industry pursues.

Micro-/Nanostructured Interface for Liquid Manipulation and Its Applications

Understanding the relationship between liquid manipulation and micro-/nanostructured interfaces has gained much attention due to the wide potential applications in many fields, such as chemical and biomedical assays, environmental protection, industry, and even daily life. Much work has been done to construct various materials with interfacial liquid manipulation abilities, leading to a range of interesting applications. Herein, different fabrication methods from the top-down approach to the bottom-up approach and subsequent surface modifications of micro-/nanostructured interfaces are first introduced. Then, interactions between the surface and liquid, including liquid wetting, liquid transportation, and a number of corresponding models, together with the definition of hydrophilic/hydrophobic, oleophilic/olephobic, the definition and mechanism of superwetting, including superhydrophobicity, superhydrophilicity, and superoleophobicity, are presented. The micro-/nanostructured interface, with major applications in self-cleaning, antifogging, anti-icing, anticorrosion, drag-reduction, oil-water separation, water collection, droplet (micro)array, and surface-directed liquid transport, is summarized, and the mechanisms underlying each application are discussed. Finally, the remaining challenges and future perspectives in this area are included.

Surface Micro- and Nanoengineering: Applications of Layer-by-Layer Technology as a Versatile Tool to Control Cellular Behavior

Extracellular matrix (ECM) cues have been widely investigated for their impact on cellular behavior. Among mechanics, physics, chemistry, and topography, different ECM properties have been discovered as important parameters to modulate cell functions, activating mechanotransduction pathways that can influence gene expression, proliferation or even differentiation. Particularly, ECM topography has been gaining more and more interest based on the evidence that these physical cues can tailor cell behavior. Here, an overview of bottom-up and top-down approaches reported to produce materials capable of mimicking the ECM topography and being applied for biomedical purposes is provided. Moreover, the increasing motivation of using the layer-by-layer (LbL) technique to reproduce these topographical cues is highlighted. LbL assembly is a versatile methodology used to coat materials with a nanoscale fidelity to the geometry of the template or to produce multilayer thin films composed of polymers, proteins, colloids, or even cells. Different geometries, sizes, or shapes on surface topography can imply different behaviors: effects on the cell adhesion, proliferation, morphology, alignment, migration, gene expression, and even differentiation are considered. Finally, the importance of LbL assembly to produce defined topographical cues on materials is discussed, highlighting the potential of micro- and nanoengineered materials to modulate cell function and fate.

Cell encapsulation in liquified compartments: Protocol optimization and challenges

Cell encapsulation is a widely used technique in the field of Tissue Engineering and Regenerative Medicine (TERM). However, for the particular case of liquefied compartmentalised systems, only a limited number of studies have been reported in the literature. We have been exploring a unique cell encapsulation system composed by liquefied and multilayered capsules. This system transfigured the concept of 3D scaffolds for TERM, and was already successfully applied for bone and cartilage regeneration. Due to a number of appealing features, we envisage that it can be applied in many other fields, including in advanced therapies or as disease models for drug discovery. In this review, we intend to highlight the advantages of this new system, while discussing the methodology, and sharing the protocol optimization and results. The different liquefied systems for cell encapsulation reported in the literature will be also discussed, considering the different encapsulation matrixes as core templates, the types of membranes, and the core liquefaction treatments.

Polysaccharide Coating of Gelatin Gels for Controlled BSA Release

Self-assembly of natural polymers constitute a powerful route for the development of functional materials. In particular, layer-by-layer (LBL) assembly constitutes a versatile technique for the nanostructuration of biobased polymers into multilayer films. Gelatin has gained much attention for its abundance, biodegradability, and excellent gel-forming properties. However, gelatin gels melt at low temperature, thus limiting its practical application. With respect to the above considerations, here, we explored the potential application of gelatin gels as a matrix for protein delivery at physiological temperature. A model protein, bovine serum albumin (BSA), was encapsulated within gelatin gels and then coated with a different number of bilayers of alginate and chitosan (10, 25, 50) in order to modify the diffusion barrier. The coated gel samples were analyzed by means of Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) and confocal Raman spectroscopy, and it was found that the multilayer coatings onto polymer film were interpenetrated to some extent within the gelatin. The obtained results inferred that the coating of gelatin gels with polysaccharide multilayer film increased the thermal stability of gelatin gels and modulated the BSA release. Finally, the influence of a number of bilayers onto the drug release mechanism was determined. The Ritger-Peppas model was found to be the most accurate to describe the diffusion mechanism.

Polyelectrolyte multilayers of poly (l-lysine) and hyaluronic acid on nanostructured surfaces affect stem cell response

Laser interference lithography (LIL) and the layer-by-layer (LbL) technique are combined here for the first time to design a system with variable nanotopographies and surface viscoelasticity to regulate cell behavior. LIL is used to generate hexagonally arranged nanostructures of gold with different periodicity. In contrast, LBL is used to assemble a multilayer system of poly-l-lysine and hyaluronic acid on top of the nanostructures. Moreover, the viscoelastic properties of that system are controlled by chemical cross-linking. We show that the topography designed with LIL is still present after multilayer deposition and that the formation of the multilayer system renders the surfaces hydrophilic, which is opposite to the hydrophobic nature of pristine nanostructures. The heterogenic system is applied to study the effect on adhesion and differentiation of human adipose-derived stem cells (hADSC). We show that hADSC spreading is increasing with cross-linking degree on flat multilayers, while it is decreasing on nanostructures modified with multilayers. In addition, early effects on signal transduction processes are seen. Finally, hADSC differentiation into chondrogenic and osteogenic lineages is superior to adipogenic lineages on nanostructures modified with multilayers. Hence, the presented system offers great potential to guide stem cell differentiation on surfaces of implants and tissue engineering scaffolds.

Properties of Therapeutic Deep Eutectic Solvents of l-Arginine and Ethambutol for Tuberculosis Treatment

The treatment for tuberculosis infection usually involves a prolonged regimen of multiple antibacterial drugs, which might lead to various secondary effects. For preventing drug resistance and side-effects of anti-tuberculosis drugs, new methods for improving the bioavailability of APIs were investigated. The strategy proposed consists of the preparation of therapeutic deep eutectic solvents (THEDES), that incorporate l-arginine and ethambutol. The eutectic mixtures were prepared by mixing the components at a certain molar ratio, until a clear liquid solution was formed. The prepared mixtures were characterized by differential scanning calorimetry (DSC), polarized optical microscopy (POM) and nuclear magnetic resonance spectroscopy (¹H and ¹³C-NMR). The solubility and permeability of the drugs when they are in the THEDES form was evaluated at 37 °C, in phosphate buffered saline (PBS). Solubility studies showed an increase of the solubility of ethambutol when incorporated in the eutectic system. The cytotoxicity was evaluated using a model cell line (Caco-2), comparing the cytotoxicity of the API incorporated in the eutectic system. We observed that the cell viability in the THEDES was affected by the presence of citric acid, and higher cytotoxicity values were observed. Nonetheless, these findings do not compromise the possibility to use these systems as new delivery systems for ethambutol and arginine.

Layer-by-layer adsorption: Factors affecting the choice of substrates and polymers

The electrostatic layer-by-layer technique for fabrication of multi-layered structures of various sizes and shapes using flat and colloidal templates coupled with polyelectrolyte layer-forming materials has attracted significant interest among both academic and industrial researchers due to its versatility and relative simplicity of the procedures involved in its execution. Fabrication of the multi-layered structures using the electrostatic layer-by-layer method involves several distinct stages each of which holds great importance when considering the production of a high-quality product. These stages include selection of materials (both template and a pair of construction polyelectrolytes), adsorption of the first polyelectrolyte layer onto the selected templates, formation of the second layer comprised of the oppositely charged polyelectrolyte and guided by the interactions between the two chosen polyelectrolytes, and multi-layering, where a selected number of layers are produced, and which is conditioned by both intrinsic properties of the involved construction materials and external fabrication conditions such as temperature, pH and ionic strength. The current review summarises the most important aspects of each stage mentioned above and gives examples of the materials suitable for utilization of the technique and describes the underlying physics involved.

Covalent layer-by-layer films: chemistry, design, and multidisciplinary applications

Covalent layer-by-layer (LbL) assembly is a powerful method used to construct functional ultrathin films that enables nanoscopic structural precision, componential diversity, and flexible design. Compared with conventional LbL films built using multiple noncovalent interactions, LbL films prepared using covalent crosslinking offer the following distinctive characteristics: (i) enhanced film endurance or rigidity; (ii) improved componential diversity when uncharged species or small molecules are stably built into the films by forming covalent bonds; and (iii) increased structural diversity when covalent crosslinking is employed in componential, spacial, or temporal (labile bonds) selective manners. In this review, we document the chemical methods used to build covalent LbL films as well as the film properties and applications achievable using various film design strategies. We expect to translate the achievement in the discipline of chemistry (film-building methods) into readily available techniques for materials engineers and thus provide diverse functional material design protocols to address the energy, biomedical, and environmental challenges faced by the entire scientific community.

Bioinspired multilayer membranes as potential adhesive patches for skin wound healing

Bioinspired and adhesive multilayer membranes are produced using the layer-by-layer (LbL) assembly of chitosan (CHT), alginate (ALG) and hyaluronic acid modified with dopamine (HA-DN). Freestanding multilayer membranes without DN are also produced as a control. The success of the synthesis of HA-DN was confirmed using UV-visible spectroscopy. Scanning electron microscopy images indicate that the surface of the DN-containing membranes is more porous than the control ones; they also present a higher average thickness value for the same number of CHT/ALG/CHT/HA(-DN) tetralayers (n = 100). Also, water uptake, mechanical strength and adhesion are enhanced with the introduction of DN moieties along the nano-layers. Besides, human dermal fibroblast viability, enhanced adhesion and proliferation were confirmed by immunofluorescence assays and by measuring both the metabolic activity and DNA content. Moreover, in vivo assays with such kinds of DN-containing multilayer membranes were performed; the application of these membranes in the treatment of dermal wounds induced in Wistar rats results in the highest decrease of inflammation of rat skin, compared with the control conditions. Overall, this investigation suggests that these mussel-inspired freestanding multilayer membranes may enhance either their mechanical performance or cellular adhesion and proliferation, leading to an improved wound healing process, being a promising material to restore the structural and functional properties of wounded skin.

Adhesive free-standing multilayer films containing sulfated levan for biomedical applications

This work is the first reporting the use of layer-by-layer to produce adhesive free-standing (FS) films fully produced using natural-based macromolecules: chitosan (CHI), alginate (ALG) and sulfated levan (L-S). The deposition conditions of the natural polymers were studied through zeta potential measurements and quartz crystal microbalance with dissipation monitoring analysis. The properties of the FS films were evaluated and compared with the control ones composed of only CHI and ALG in order to assess the influence of levan polysaccharide introduced in the multilayers. Tensile tests, dynamic mechanical analysis and single lap shear strength tests were performed to evaluate the mechanical properties of the prepared FS films. The presence of L-S conferred both higher tensile strength and shear strength to the developed FS membranes. The results showed an adhesion strength 4 times higher than the control (CHI/ALG) FS films demonstrating the adhesive character of the FS films containing L-S. Morphological and topography studies were carried out revealing that the crosslinking reaction granted the L-S based FS film with a higher roughness and surface homogeneity. Preliminary biological assays were performed by cultivating myoblasts cells on the surface of the produced FS films. Both crosslinked and uncrosslinked FS films containing L-S were cytocompatible and myoconductive.

STATEMENT OF SIGNIFICANCE

Sutures remain as the "gold standard" for wound closure and bleeding control; however they still have limitations such as, high infection rate, inconvenience in handling, and concern over possible transmission of blood-borne disease through the use of needles. One of the challenges of tissue engineering consist on the design and development of biocompatible tissue adhesives and sealants with high adhesion properties to repair or attach devices to tissues. In this work, the introduction of sulfated levan (L-S) on multilayered free-standing membranes was proposed to confer adhesive properties. Moreover, the films were myoconductive even in the absence of crosslinking just by the presence of L-S. This study provides a promising strategy to develop biological adhesives and for cardiac tissue engineering applications.

Cross-linking multilayers of poly-l-lysine and hyaluronic acid: Effect on mesenchymal stem cell behavior

BACKGROUND

Cells possess a specialized machinery through which they can sense physical as well as chemical alterations in their surrounding microenvironment that affect their cellular behavior.

AIM

In this study, we aim to establish a polyelectrolyte multilayer system of 24 layers of poly-l-lysine and hyaluronic acid to control stem cell response after chemical cross-linking.

METHODS AND RESULTS

The multilayer build-up process is monitored using different methods, which show that the studied polyelectrolyte multilayer system grows exponentially following the islands and islets theory. Successful chemical cross-linking is monitored by an increased zeta potential toward negative magnitude and an extraordinary growth in thickness. Human adipose-derived stem cells are used here and a relationship between cross-linking degree and cell spreading is shown as cells seeded on higher cross-linked polyelectrolyte multilayer show enhanced spreading. Furthermore, cells that fail to establish focal adhesions on native and low cross-linked polyelectrolyte multilayer films do not proliferate to a high extent in comparison to cells seeded on highly cross-linked polyelectrolyte multilayer, which also show an increased metabolic activity. Moreover, this study shows the relation between cross-linking degree and human adipose-derived stem cell lineage commitment. Histological staining reveals that highly cross-linked polyelectrolyte multilayers support osteogenic differentiation, whereas less cross-linked and native polyelectrolyte multilayers support adipogenic differentiation in the absence of any specific inducers.

CONCLUSION

Owing to the precise control of polyelectrolyte multilayer properties such as potential, wettability, and viscoelasticity, the system presented here offers great potential for guided stem cell differentiation in regenerative medicine, especially in combination with materials exhibiting a defined surface topography.

Engineered tubular structures based on chitosan for tissue engineering applications

The development of versatile tubular structures is a subject of broad interest in tissue engineering applications. Herein, we demonstrate the production of tubular structures based on chitosan through a combination of dipping, freeze-drying and supercritical technology approaches. The combination of these techniques yields versatile tubes with a perfectly defined hollow imprint, which upon chemical cross-linking with genipin acquire enhanced mechanical properties (Young Modulus ( E) and ultimate tensile stress (σ_max)), as well as improved stability in wet conditions. The biological performance reveals that cells remain attached, well-spread and viable on the surface of cross-linked tubes. As so, is envisioned that our methodology opens up new avenues on tissue engineering approaches, where the design of tubular structures with tuned length, diameter and elasticity is required.

* Engineering Membranes for Bone Regeneration

This review is focused on the use of membranes for the specific application of bone regeneration. The first section focuses on the relevance of membranes in this context and what are the specifications that they should possess to improve the regeneration of bone. Afterward, several techniques to engineer bone membranes by using "bulk"-like methods are discussed, where different parameters to induce bone formation are disclosed in a way to have desirable structural and functional properties. Subsequently, the production of nanostructured membranes using a bottom-up approach is discussed by highlighting the main advances in the field of bone regeneration. Primordial importance is given to the promotion of osteoconductive and osteoinductive capability during the membrane design. Whenever possible, the films prepared using different techniques are compared in terms of handability, bone guiding ability, osteoinductivity, adequate mechanical properties, or biodegradability. A last chapter contemplates membranes only composed by cells, disclosing their potential to regenerate bone.

Multilayered Films Produced by Layer-by-Layer Assembly of Chitosan and Alginate as a Potential Platform for the Formation of Human Adipose-Derived Stem Cell aggregates

The construction of multilayered films with tunable properties could offer new routes to produce biomaterials as a platform for 3D cell cultivation. In this study, multilayered films produced with five bilayers of chitosan and alginate (CHT/ALG) were built using water-soluble modified mesyl and tosyl–CHT via layer-by-layer (LbL) self-assembly. NMR results demonstrated the presences of mesyl (2.83 ppm) and tosyl groups (2.39, 7.37 and 7.70 ppm) in the chemical structure of modified chitosans. The buildup of multilayered films was monitored by quartz-crystal-microbalance (QCM-D) and film thickness was estimated using the Voigt-based viscoelastic model. QCM-D results demonstrated that CHT/ALG films constructed using mesyl or tosyl modifications (mCHT/ALG) were significantly thinner in comparison to the CHT/ALG films constructed with unmodified chitosan (p < 0.05). Adhesion analysis demonstrated that human adipose stem cells (hASCs) did not adhere to the mCHT/ALG multilayered films and formed aggregates with sizes between ca. 100–200 µm. In vitro studies on cell metabolic activity and live/dead staining suggested that mCHT/ALG multilayered films are nontoxic toward hACSs. Multilayered films produced via LbL assembly of ALG and off-the-shelf, water-soluble modified chitosans could be used as a scaffold for the 3D aggregates formation of hASCs in vitro.

Control of Cell Alignment and Morphology by Redesigning ECM-Mimetic Nanotopography on Multilayer Membranes

Inspired by native extracellular matrix (ECM) together with the multilevel architecture observed in nature, a material which topography recapitulates topographic features of the ECM and the internal architecture mimics the biological materials organization is engineered. The nanopatterned design along the XY plane is combined with a nanostructured organization along the Z axis on freestanding membranes prepared by layer-by-layer deposition of chitosan and chondroitin sulfate. Cellular behavior is monitored using two different mammalian cell lines, fibroblasts (L929) and myoblasts (C2C12), in order to perceive the response to topography. Viability, proliferation, and morphology of L929 are sensitively controlled by topography; also differentiation of C2C12 into myotubes is influenced by the presence of nanogrooves. This kind of nanopatterned structure has also been associated with strong cellular alignment. To the best of the knowledge, it is the first time that such a straightforward and inexpensive strategy is proposed to produce nanopatterned freestanding multilayer membranes. Controlling cellular alignment plays a critical role in many human tissues, such as muscles, nerves, or blood vessels, so these membranes can be potentially useful in specific tissue regeneration strategies.

Multilayered membranes with tuned well arrays to be used as regenerative patches

Membranes have been explored as patches in tissue repair and regeneration, most of them presenting a flat geometry or a patterned texture at the nano/micrometer scale. Herein, a new concept of a flexible membrane featuring well arrays forming pore-like environments to accommodate cell culture is proposed. The processing of such membranes using polysaccharides is based on the production of multilayers using the layer-by-layer methodology over a patterned PDMS substrate. The detached multilayered membrane exhibits a layer of open pores at one side and a total thickness of 38±2.2µm. The photolithography technology used to produce the molds allows obtaining wells on the final membranes with a tuned shape and micro-scale precision. The influence of post-processing procedures over chitosan/alginate films with 100 double layers, including crosslinking with genipin or fibronectin immobilization, on the adhesion and proliferation of human osteoblast-like cells is also investigated. The results suggest that the presence of patterned wells affects positively cell adhesion, morphology and proliferation. In particular, it is seen that cells colonized preferentially the well regions. The geometrical features with micro to sub-millimeter patterned wells, together with the nano-scale organization of the polymeric components along the thickness of the film will allow to engineer highly versatile multilayered membranes exhibiting a pore-like microstructure in just one of the sides, that could be adaptable in the regeneration of multiple tissues.

STATEMENT OF SIGNIFICANCE

Flexible multilayered membranes containing multiple micro-reservoirs are found as potential regenerative patches. Layer-by-layer (LbL) methodology over a featured PDMS substrate is used to produce patterned membranes, composed only by natural-based polymers, that can be easily detached from the PDMS substrate. The combination of nano-scale control of the polymeric organization along the thickness of the chitosan/alginate (CHT/ALG) membranes, provided by LbL, together with the geometrical micro-scale features of the patterned membranes offers a uniqueness system that allows cells to colonize 3-dimensionally. This study provides a promising strategy to control cellular spatial organization that can face the region of the tissue to regenerate.

Tuning cell adhesive properties via layer-by-layer assembly of chitosan and alginate

Understanding the mechanisms controlling cell-multilayer film interactions is crucial to the successful engineering of these coatings for biotechnological and biomedical applications. Herein, we present a strategy to tune the cell adhesive properties of multilayers based on marine polysaccharides with and without cross-linking and/or coating with extracellular matrix proteins. Chemical cross-linking of multilayers improved mechanical properties of the coatings but also elicited changes in surface chemistry that alter the adhesion of human umbilical vein endothelial cells. We evaluated a strategy to decouple the mechanical and chemical properties of these films, enabling the transition from cell-adhesive to cell-resistant multilayers. Addition of chitosan/alginate multilayers on top of cross-linked films decreased endothelial cell adhesion, spreading, and proliferation to similar levels as uncross-linked films. Our findings highlight the key role of surface chemistry in cell-multilayer film interactions, and these engineered nanocoatings represent a tunable model of cell adhesive and non-adhesive multilayered films.

STATEMENT OF SIGNIFICANCE

Multilayered films based on marine-derived polysaccharides were obtained by layer-by-layer (LbL). Biological tests with human umbilical vein endothelial cells (HUVECs) showed the potential of these films to tailor cell adhesion, spreading and proliferation. These multilayered films promise to be versatile and tunable model of cell adhesive and non-adhesive films.

A comparison between pure active pharmaceutical ingredients and therapeutic deep eutectic solvents: Solubility and permeability studies

THEDES, so called therapeutic deep eutectic solvents are here defined as a mixture of two components, which at a particular molar composition become liquid at room temperature and in which one of them is an active pharmaceutical ingredient (API). In this work, THEDES based on menthol complexed with three different APIs, ibuprofen (ibu), BA (BA) and phenylacetic acid (PA), were prepared. The interactions between the components that constitute the THEDES were studied by NMR, confirming that the eutectic system is formed by H-bonds between menthol and the API. The mobility of the THEDES components was studied by PFGSE NMR spectroscopy. It was determined that the self-diffusion of the species followed the same behavior as observed previously for ionic liquids, in which the components migrate via jumping between voids in the suprastructure created by punctual thermal fluctuations. The solubility and permeability of the systems in an isotonic solution was evaluated and a comparison with the pure APIs was established through diffusion and permeability studies carried out in a Franz cell. The solubility of the APIs when in the THEDES system can be improved up to 12 fold, namely for the system containing ibu. Furthermore, for this system the permeability was calculated to be 14×10^-5cm/s representing a 3 fold increase in comparison with the pure API. With the exception of the systems containing PA an increase in the solubility, coupled with an increase in permeability was observed. In this work, we hence demonstrate the efficiency of THEDES as a new formulation for the enhancement of the bioavailability of APIs by changing the physical state of the molecules from a solid dosage to a liquid system.

Functional Graphene Nanomaterials Based Architectures: Biointeractions, Fabrications, and Emerging Biological Applications

Functional graphene nanomaterials (FGNs) are fast emerging materials with extremely unique physical and chemical properties and physiological ability to interfere and/or interact with bioorganisms; as a result, FGNs present manifold possibilities for diverse biological applications. Beyond their use in drug/gene delivery, phototherapy, and bioimaging, recent studies have revealed that FGNs can significantly promote interfacial biointeractions, in particular, with proteins, mammalian cells/stem cells, and microbials. FGNs can adsorb and concentrate nutrition factors including proteins from physiological media. This accelerates the formation of extracellular matrix, which eventually promotes cell colonization by providing a more beneficial microenvironment for cell adhesion and growth. Furthermore, FGNs can also interact with cocultured cells by physical or chemical stimulation, which significantly mediate their cellular signaling and biological performance. In this review, we elucidate FGNs-bioorganism interactions and summarize recent advancements on designing FGN-based two-dimensional and three-dimensional architectures as multifunctional biological platforms. We have also discussed the representative biological applications regarding these FGN-based bioactive architectures. Furthermore, the future perspectives and emerging challenges will also be highlighted. Due to the lack of comprehensive reviews in this emerging field, this review may catch great interest and inspire many new opportunities across a broad range of disciplines.