Attachment of 3-(Aminopropyl)triethoxysilane on silicon oxide surfaces: dependence on solution temperature

An investigation of a strengthening polysaccharide interfacial membrane strategy utilizing an anionic polysaccharide-alkaline ligand interfacial assembly for all-liquid printing

The applications of polysaccharides as emulsifiers are limited due to the lack of hydrophobicity. However, traditional hydrophobic modification methods used for polysaccharides are complicated and involve significant mechanical and thermal losses. In this study, soy hull polysaccharide (SHP) and terminally aminopropylated polydimethylsiloxane (NPN) were selected to investigate the feasibility of a simple and green interfacial membrane strengthening strategy based on the interfacial polymerization of anionic polysaccharides and fat-soluble alkaline ligands. Our results show that deprotonated SHP and protonated NPN can be complexed at the water/oil (W/O) interface, reduce interfacial tension, and form a strong membrane structure. Moreover, they can quickly form a membrane at the W/O interface upon the moment of contact to produce stable all-liquid printing products with complex patterns. However, the molecular weight of NPN affects the complexation reaction. Consequently, this study has long-term implications to expanding the areas of application for anionic polysaccharides.

Is additional silane application necessary for a new silane-containing universal adhesive to bond to glass ceramics?

OBJECTIVE

To evaluate the in vitro influence of prior silane application on the microshear bond strength (μSBS) of Scotchbond Universal Plus to glass ceramic.

MATERIALS AND METHODS

Thirty blocks of lithium disilicate ceramic were etched with hydrofluoric acid for 20 s and distributed into Group 1 (no silane and no adhesive), Group 2 (adhesive), Group 3 (silane + adhesive). Three cylinders of resin cement were made on each ceramic block. Five blocks (n = 15 cylinders) were subjected to the μSBS test after 24 h, and the other five blocks (n = 15 cylinders) were tested after 6 months of water storage.

RESULTS

According to two-way ANOVA, followed by Tukey's test, the means of μSBS (MPa), denoted by different letters, show significant differences (p < 0.05): after 24 h-Group 1 (31.7)B, Group 2 (43.3)A, and Group 3 (31.3)B; after 6 months-Group 1 (14.8)B, Group 2 (33.6)A, and Group 3 (30.3)A. After 6 months of storage, there was a significant decrease in μSBS for Groups 1 and 2, along with an increase in adhesive failures across all groups.

CONCLUSIONS

Prior application of silane did not increase the μSBS between Scotchbond Universal Plus and ceramic, and there was degradation at the bond interface over time.

CLINICAL SIGNIFICANCE

Prior application of a silane agent is not necessary when using Scotchbond Universal Plus for bonding to glass ceramics. Regardless of the prior application of silane, there is degradation at the bond interface over time.

Mechanophysical and Anti-Adhesive Properties of a Nanoclay-Containing PMMA Denture Resin

Poly(methyl methacrylate) (PMMA) is commonly used for dental dentures, but it has the drawback of promoting oral health risks due to oral bacterial adhesion. Recently, various nanoparticles have been incorporated into PMMA to tackle these issues. This study aims to investigate the mechanophysical and antimicrobial adhesive properties of a denture resin by incorporating of nanoclay into PMMA. Specimens were prepared by adding 0, 1, 2, and 4 wt % surface-modified nanoclay (Sigma) to self-polymerizing PMMA denture resin. These specimens were then evaluated using FTIR, TGA/DTG, and FE-SEM with EDS. Various mechanical and surface physical properties, including nanoindentation, were measured and compared with those of pure PMMA. Antiadhesion experiments were conducted by applying a Candida albicans (ATCC 11006) suspension to the surface of the specimens. The antiadhesion activity of C. albicans was confirmed through a yeast-wall component (mannan) and mRNA-seq analysis. The bulk mechanical properties of nanoclay-PMMA composites were decreased compared to those of pure PMMA, while the flexural strength and modulus met the ISO 20795-1 requirement. However, there were no significant differences in the nanoindentation hardness and elastic modulus. The surface energy revealed a significant decrease at 4 wt % nanoclay-PMMA. The antiadhesion effect of Candida albicans was evident along with nanoclay content in the nanocomposites and confirmed by the reduced attachment of mannan on nanoclay-PMMA composites. mRNA-seq analysis supported overall transcriptome changes in altering attachment and metabolism behaviors on the surface. The nanoclay-PMMA materials showed a lower surface energy as the content increased, leading to an antiadhesion effect against Candida albicans. These findings indicate that incorporating nanoclay into PMMA surfaces could be a valuable strategy for preventing the fungal biofilm formation of denture base materials.

Optimization and characterization of silver nanoparticle-modified luffa for the adsorption of ketoprofen and reactive yellow 15 from aqueous solutions

In the current work, luffa was modified with silver nanoparticles to prepare LF/AgNPs adsorbent for the elimination of ketoprofen and reactive yellow 15 (RY15) from aqueous media. Various characterization techniques, including FT-IR, XRD, BET, and SEM-EDS analysis, were employed to confirm the successful modification of LF/AgNPs. Several key parameters such as contact time, adsorbent dosage, concentration, pH, and agitation technique were fine-tuned to optimize the adsorption process. Ketoprofen removal was found to be most effective in weakly acidic conditions (pH = 5), while reactive yellow 15 adsorption was enhanced in an acidic environment (pH = 2). At 298 K, the highest adsorption capacities reached 56.88 mg/g for ketoprofen and 97.76 mg/g for reactive yellow 15. In both scenarios involving the elimination of ketoprofen and RY15, the Temkin isotherm exhibits higher R2 values, specifically 0.997 for ketoprofen and 0.963 for RY15, demonstrating a strong correlation with the observed adsorption data. Additionally, the kinetics of ketoprofen adsorption were best described by the Pseudo-first order model (R2 = 0.989), whereas the Pseudo-second order model provided the most accurate fit for reactive yellow 15 adsorption (R2 = 0.997). Importantly, the LF/AgNPs adsorbent displayed consistent performance over five consecutive reuse cycles, affirming its stability and efficacy in removing both contaminants. These findings underscore the exceptional potential of LF/AgNPs as a reliable adsorbent for the removal of reactive yellow 15 and ketoprofen from aqueous solutions.

Surface engineering of mesoporous bioactive glass nanoparticles with bacteriophages for enhanced antibacterial activity

Binary SiO2-CaO mesoporous bioactive glass nanoparticles (MBGNs) are multifunctional biomaterials able to promote osteogenic, angiogenic, and immunomodulatory activities. MBGNs have been applied in a variety of tissue regeneration strategies. However, MBGNs lack strong antibacterial activity and current strategies (loading of antibacterial ions or antibiotics) toward enhanced antibacterial activity may cause cytotoxicity or antibiotic resistance. Here we engineered MBGNs using bacteriophages (phages) to enhance the antibacterial activity. Salmonella Typhimurium (S. T) phage PFPV25.1 that can infect Salmonella enterica serovar Typhimurium strain LT2 was used as a model phage to engineer MBGNs. MBGNs were first modified with amine groups to enhance the affinity between phages and MBGNs surfaces. Afterward, the physicochemical and antibacterial activity of phage-engineered MBGNs was evaluated. The results showed that S. T phage PFPV25.1 was successfully bound onto MBGNs surfaces without losing their bioactivity. A higher quantity of phages could be bounded onto amine-functionalized MBGNs than onto non-functionalized MBGNs. Phages on amine-functionalized MBGNs exhibited higher antibacterial activity. The stability test showed that phages could remain on amine-functionalized MBGNs for over 28 days. This work provides valuable information on developing phage-modified MBGNs as a new and effective antibacterial system for biomedical applications.

Preparation and Characterization of Perfluoropolyether-Silane@Ethye Cellulose Polymeric Microcapsules

A novel polymeric microcapsule was designed and synthesized using perfluoropolyether silane (PFPE-silane) as a superhydrophobic core material and ethyl cellulose (EC) as a shell material. The effects of the stirring rate and the core-to-shell ratio on the synthesized microcapsules were investigated. The physicochemical properties of the polymeric microcapsules were evaluated using scanning electron microscopy, fourier transform infrared spectroscopy, thermogravimetric analysis, laser particle size analysis, and wettability analysis. The results showed that when the stirring rate was 650 rpm and the core-to-shell ratio was 1:1, well-distributed and uniformly dispersed microcapsules could be obtained. The results also indicated that the prepared polymeric microcapsules were spherical particles with micropores on the surface, and they had an average particle size of 165.71 μm. The EC shells could effectively prevent the thermal decomposition of PFPE-silane during cement hydration, and the PFPE-silane also exhibited excellent hydrophobicity. The specially designed structure of this polymeric microcapsule suggests its potential for enhancing the corrosion resistance of reinforced concrete structures.

Surface chemistry applications and development of immunosensors using electrochemical impedance spectroscopy: A comprehensive review

Immunosensors are promising alternatives as detection platforms for the current gold standards methods. Electrochemical immunosensors have already proven their capability for the sensitive, selective, detection of target biomarkers specific to COVID-19, varying cancers or Alzheimer's disease, etc. Among the electrochemical techniques, electrochemical impedance spectroscopy (EIS) is a highly sensitive technique which examines the impedance of an electrochemical cell over a range of frequencies. There are several important critical requirements for the construction of successful impedimetric immunosensor. The applied surface chemistry and immobilisation protocol have impact on the electroanalytical performance of the developed immunosensors. In this Review, we summarise the building blocks of immunosensors based on EIS, including self-assembly monolayers, nanomaterials, polymers, immobilisation protocols and antibody orientation.

Highly Hydrophobic Gelatin Nanocomposite Film Assisted by Nano-ZnO/(3-Aminopropyl) Triethoxysilane/Stearic Acid Coating for Liquid Food Packaging

Biodegradable gelatin (G) food packaging films are in increasing demand as the substitution of petroleum-based preservative materials. However, G packaging films universally suffer from weak hydrophobicity in practical applications. Constructing a hydrophobic micro/nanocoating with low surface energy is an effective countermeasure. However, the poor compatibility with the hydrophilic G substrate often leads to the weak interfacial adhesion and poor durability of the hydrophobic coating. To overcome this obstacle, we used (3-aminopropyl) triethoxysilane (APS) as an interfacial bridging agent to prepare a highly hydrophobic, versatile G nanocomposite film. Specifically, tannic acid (TA)-modified nanohydroxyapatite (n-HA) particles (THA) were introduced in G matrix (G-THA) to improve the mechanical properties. Micro/nanostructure with low surface energy composed of nanozinc oxide (Nano-ZnO)/APS/stearic acid (SA) (NAS) was constructed on the surface of G-THA film (G-THA/NAS) through one-step spray treatment. Consequently, as-prepared G-THA/NAS film presented excellent mechanics (tensile strength: 7.6 MPa, elongation at break: 292.7%), water resistance ability (water contact angle: 150.4°), high UV-shielding (0% transmittance at 200 nm), degradability (100% degradation rate after buried in the natural soil for 15 days), antioxidant (78.8% of 2,2-diphenyl-1-picrylhydrazyl radical scavenging activity), and antimicrobial (inhibition zone against Escherichia coli: 15.0 mm and Staphylococcus aureus: 16.5 mm) properties. It should be emphasized that the bridging function of APS significantly improves the interfacial adhesion ability of the NAS coating with more than 95% remaining area after the cross-cut adhesion test. Meanwhile, the G-THA/NAS film could maintain stable and long-lasting hydrophobic surfaces against UV radiation, high temperature, and abrasion. Based on these multifunctional properties, the G-THA/NAS film was successfully applied as a liquid packaging material. To sum up, we provide a feasible and effective method to prepare high-performance green packaging films.

Surface Functionalised Optical Fibre for Detection of Hydrogen Sulphide

Dysregulated production of hydrogen sulphide in the human body has been associated with various diseases including cancer, underlining the importance of accurate detection of this molecule. Here, we report the detection of hydrogen sulphide using fluorescence-emission enhancement of two 1,8-naphthalimide fluorescent probes with an azide moiety in position 4. One probe, serving as a control, featured a methoxyethyl moiety through the imide to evaluate its effectiveness for hydrogen sulphide detection, while the other probe was modified with (3-aminopropyl)triethoxysilane (APTES) to enable direct covalent attachment to an optical fibre tip. We coated the optical fibre tip relatively homogeneously with the APTES-azide fluorophore, as confirmed via x-ray photoelectron spectroscopy (XPS). The absorption and fluorescence responses of the control fluorophore free in PBS were analysed using UV-Vis and fluorescence spectrophotometry, while the fluorescence emission of the APTES-azide fluorophore-coated optical fibres was examined using a simple, low-cost optical fibre-based setup. Both fluorescent probes exhibited a significant increase (more than double the initial value) in fluorescence emission upon the addition of HS- when excited with 405 nm. However, the fluorescence enhancement of the coated optical fibres demonstrated a much faster response time of 2 min (time for the fluorescence intensity to reach 90% of its maximum value) compared to the control fluorophore in solution (30 min). Additionally, the temporal evolution of fluorescence intensity of the fluorophore coated on the optical fibre was studied at two pH values (7.4 and 6.4), demonstrating a reasonable overlap and confirming the compound pH insensitivity within this range. The promising results from this study indicate the potential for developing an optical fibre-based sensing system for HS- detection using the synthesised fluorophore, which could have significant applications in health monitoring and disease detection.

Plasmonic Coupling on an Optical Microfiber Surface: Enabling Single-Molecule and Noninvasive Dopamine Detection

Optical fibers can be effective biosensors when employed in early-stage diagnostic point-of-care devices as they can avoid interference from molecules with similar redox potentials. Nevertheless, their sensitivity needs to be improved for real-world applications, especially for small-molecule detection. This work demonstrates an optical microfiber biosensor for dopamine (DA) detection based on the DA-binding-induced aptamer conformational transitions that occur at plasmonic coupling sites on a double-amplified nanointerface. The sensor exhibits ultrahigh sensitivity when detecting DA molecules at the single-molecule level; additionally, this work provides an approach for overcoming optical device sensitivity limits, further extending optical fiber single-molecule detection to a small molecule range (e.g., DA and metal ions). The selective energy enhancement and signal amplification at the binding sites effectively avoid nonspecific amplification of the whole fiber surface which may lead to false-positive results. The sensor can detect single-molecule DA signals in body-fluids. It can detect the released extracellular DA levels and monitor the DA oxidation process. An appropriate aptamer replacement allows the sensor to be used for the detection of other target small molecules and ions at the single-molecule level. This technology offers alternative opportunities for developing noninvasive early-stage diagnostic point-of-care devices and flexible single-molecule detection techniques in theoretical research.

Design of a 3D Amino-Functionalized Rice Husk Ash Nano-Silica/Chitosan/Alginate Composite as Support for Laccase Immobilization

Recycling of agro-industrial waste is one of the major issues addressed in recent years aimed at obtaining products with high added value as a future alternative to traditional ones in the per-spective of a bio-based and circular economy. One of the most produced wastes is rice husk and it is particularly interesting because it is very rich in silica, a material with a high intrinsic value. In the present study, a method to extract silica from rice husk ash (RHA) and to use it as a carrier for the immobilization of laccase from Trametes versicolor was developed. The obtained mesoporous nano-silica was characterized by X-ray diffraction (XRD), ATR-FTIR spectroscopy, Scanning Elec-tron Microscopy (SEM), and Energy Dispersive X-ray spectroscopy (EDS). A nano-silica purity of about 100% was found. Nano-silica was then introduced in a cross-linked chitosan/alginate scaffold to make it more easily recoverable after reuse. To favor laccase immobilization into the composite scaffold, functionalization of the nano-silica with (γ-aminopropyl) triethoxysilane (APTES) was performed. The APTES/RHA nano-silica/chitosan/alginate (ARCA) composite al-lowed to obtain under mild conditions (pH 7, room temperature, 1.5 h reaction time) a robust and easily reusable solid biocatalyst with 3.8 U/g of immobilized enzyme which maintained 50% of its activity after six reuses. The biocatalytic system, tested for syringic acid bioremediation, was able to totally oxidize the contaminant in 24 h.

Effect of Plasma Excitation Power on the SiOxCyHz/TiOx Nanocomposite

Titanium dioxide has attracted a great deal of attention in the field of environmental purification due to its photocatalytic activity under ultraviolet light. Photocatalytic efficiency and the energy required to initiate the process remain the drawbacks that hinder the widespread adoption of the process. Consistently with this, it is proposed here the polymerization of hexamethyldisiloxane fragments simultaneously to TiO₂ sputtering for the production of thin films in low-pressure plasma. The effect of plasma excitation power on the molecular structure and chemical composition of the films was evaluated by infrared spectroscopy. Wettability and surface energy were assessed by a sessile drop technique, using deionized water and diiodomethane. The morphology and elemental composition of the films were determined using scanning electron microscopy and energy dispersive spectroscopy, respectively. The thickness and roughness of the resulting films were measured using profilometry. Organosilicon-to-silica films, with different properties, were deposited by combining both deposition processes. Titanium was detected from the structures fabricated by the hybrid method. It has been observed that the proportion of titanium and particles incorporated into silicon-based matrices depends on the plasma excitation power. In general, a decrease in film thickness with increasing power has been observed. The presence of Ti in the plasma atmosphere alters the plasma deposition mechanism, affecting film deposition rate, roughness, and wettability. An interpretation of the excitation power dependence on the plasma activation level and sputtering yield is proposed. The methodology developed here will encourage researchers to create TiO₂ films on a range of substrates for their prospective use as sensor electrodes, water and air purification systems, and biocompatible materials.

The Mechanical Properties Relationship of Radiation-Cured Nanocomposites Based on Acrylates and Cationic Polymerized Epoxies and the Composition of Silane-Modified Tungsten Disulfide Nanoparticles

The effect of semiconducting tungsten disulfide (WS₂) nanoparticles (NPs), functionalized by either methacryloxy, glycidyl, vinyl, or amino silanes, has been studied in photocuring of acrylate and epoxy resins (the latter photocured according to a cationic mechanism). The curing time, degree of curing (DC), thermal effects, and mechanical properties of the radiation-cured resins were investigated. X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) analyses confirmed that a silane coating was formed (1-4 nm) on the NPs' surface having a thickness of 1-4 nm. Fourier transition infrared (FTIR) was used to determine the DC of the nanocomposite resin. The curing time of the epoxy resin, at 345-385 nm wavelength, was 10 to 20 s, while for acrylate, the curing time was 7.5 min, reaching 92% DC in epoxy and 84% in acrylate. The glass transition temperature (Tg) of the photocured acrylates in the presence of WS₂ NPs increased. In contrast to the acrylate, the epoxy displayed no significant variations of the Tg. It was found that the silane surface treatments enhanced the DC. Significant increases in impact resistance and enhancement in shear adhesion strength were observed when the NPs were treated with vinyl silane. A previous study has shown that the addition of WS₂ NPs at a concentration of 0.5 wt.% is the optimal loading for improving the resin's mechanical properties. This study supports these earlier findings not only for the unmodified NPs but also for those functionalized with silane moieties. This study opens new vistas for the photocuring of resins and polymers in general when incorporating WS₂ NPs.

A highly sensitive and selective detection of 2,4,6-trinitrotoluene (TNT) using a peptide-functionalized silicon nanowire array sensor

A highly sensitive and specific detection of 2,4,6-trinitrotoluene (TNT), a typical nitrated aromatic explosive, was demonstrated by a silicon nanowire (SiNW) array sensor. The SiNW array devices were self-assembled and functionalized with the anti-TNT peptide to obtain unique sensitivity toward TNT. Also, the effect of the biointerfacing linker's chemistry and Debye screening with varied ionic strength of phosphate buffer solution (PBS) on TNT binding response signals were investigated. The optimization of the peptide-functionalized SiNW array sensor showed high sensitivity for TNT with a detection limit of 0.2 fM, the highest sensitivity reported to date. These initial promising results may help accelerate the development of portable sensors for femtomolar level TNT detection.

Revisiting Alkoxysilane Assembly on Silica Surfaces: Grafting versus Homo-Condensation in Solution

Silica surface functionalization is often done through the condensation of functional silanes on silanols, silica surfaces' terminal groups. APTES, aminopropyltriethoxysilane, is widely used due to its assumed high reactivity with silanols, kinetically promoted by the catalytic action of the terminal amine function. Here, we revisit, based on a quantitative analysis by solid-state ²⁹Si NMR, the assembly of this silane on silica surfaces to investigate whether its presence results from grafting, i.e., hetero-condensation with silanol groups or from homo-condensation of silane molecules in solution leading to polycondensates physisorbed on silica. We investigate the interaction of APTES with a crystalline layered silicate, ilerite, and with amorphous nonporous silica. We also studied a second silane, cyanopropyltrichlorosilane (CPTCS), terminated with a nitrile group. Our results undoubtedly prove that while CPTCS is grafted on the silica surface, the presence of APTES on silica and silicate materials is only marginally associated with silanol consumption. The analysis of the signal related to silicon atoms from silanes (Tⁿ species) and those from silica (Qⁿ species) allowed for the accurate estimation of the extent of homo-condensation vs grafting based on the ratio of T-O-T/Q-O-T siloxane bridges. These findings deeply question the well-established certainties on APTES assembly on silica that should no longer be seen as grafting of alkoxysilane by hetero-condensation with silanol groups but more accurately as a homo-condensed network of silanes, predominantly physisorbed on the surface but including some sparse anchoring points to the surface involving less than 6% of the overall silanol groups.

Carrier density tuning in CuS nanoparticles and thin films by Zn doping via ion exchange

Copper sulphide (covellite) nanoplatelets have recently emerged as a plasmonic platform in the near-infrared with ultrafast nonlinear optical properties. Here we demonstrate that the free-carrier density in CuS, which is an order of magnitude lower than in traditional plasmonic metals, can be further tuned by chemical doping. Using ion exchange to replace Cu with an increasing content of Zn in the nanoparticles, the free-hole density can be lowered, resulting in a long-wavelength shift of the localised plasmon resonances from 1250 nm to 1750 nm. The proposed approach provides new opportunities for tuning the plasmonic response of covellite nanocrystals as well as the carrier relaxation time which decreases for lower free-carrier densities.

Review: 3-Aminopropyltriethoxysilane (APTES) Deposition Methods on Oxide Surfaces in Solution and Vapor Phases for Biosensing Applications

Surface functionalization and bioreceptor immobilization are critical processes in developing a highly sensitive and selective biosensor. The silanization process with 3-aminopropyltriethoxysilane (APTES) on oxide surfaces is frequently used for surface functionalization because of beneficial characteristics such as its bifunctional nature and low cost. Optimizing the deposition process of the APTES layer to obtain a monolayer is crucial to having a stable surface and effectively immobilizing the bioreceptors, which leads to the improved repeatability and sensitivity of the biosensor. This review provides an overview of APTES deposition methods, categorized into the solution-phase and vapor-phase, and a comprehensive summary and guide for creating stable APTES monolayers on oxide surfaces for biosensing applications. A brief explanation of APTES is introduced, and the APTES deposition methods with their pre/post-treatments and characterization results are discussed. Lastly, APTES deposition methods on nanoparticles used for biosensors are briefly described.

Surface Functionalization and Texturing of Optical Metasurfaces for Sensing Applications

Optical metasurfaces are planar metamaterials that can mediate highly precise light-matter interactions. Because of their unique optical properties, both plasmonic and dielectric metasurfaces have found common use in sensing applications, enabling label-free, nondestructive, and miniaturized sensors with ultralow limits of detection. However, because bare metasurfaces inherently lack target specificity, their applications have driven the development of surface modification techniques that provide selectivity. Both chemical functionalization and physical texturing methodologies can modify and enhance metasurface properties by selectively capturing analytes at the surface and altering the transduction of light-matter interactions into optical signals. This review summarizes recent advances in material-specific surface functionalization and texturing as applied to representative optical metasurfaces. We also present an overview of the underlying chemistry driving functionalization and texturing processes, including detailed directions for their broad implementation. Overall, this review provides a concise and centralized guide for the modification of metasurfaces with a focus toward sensing applications.

Self-Assembled Au Nanoparticle Monolayers on Silicon in Two- and Three-Dimensions for Surface-Enhanced Raman Scattering Sensing

Gold nanoparticle/silicon composites are canonical substrates for sensing applications because of their geometry-dependent physicochemical properties and high sensing activity via surface-enhanced Raman spectroscopy (SERS). The self-assembly of gold nanoparticles (AuNPs) synthesized via wet-chemistry on functionalized flat silicon (Si) and vertically aligned Si nanowire (VA-SiNW) arrays is a simple and cost-effective approach to prepare such substrates. Herein, we report on the critical parameters that influence nanoparticle coverage, aggregation, and assembly sites in two- and three-dimensions to prepare substrates with homogeneous optical properties and SERS activity. We show that the degree of AuNP aggregation on flat Si depends on the silane used for the Si functionalization, while the AuNP coverage can be adjusted by the incubation time in the AuNP solution, both of which directly affect the substrate properties. In particular, we report the reproducible synthesis of nearly touching AuNP chain monolayers where the AuNPs are separated by nanoscale gaps, likely to be formed due to the capillary forces generated during the drying process. Such substrates, when used for SERS sensing, produce a uniform and large enhancement of the Raman signal due to the high density of hot spots that they provide. We also report the controlled self-assembly of AuNPs on VA-SiNW arrays, which can provide even higher Raman signal enhancement. The directed assembly of the AuNPs in specific regions of the SiNWs with a control over NP density and monolayer morphology (i.e., isolated vs nearly touching NPs) is demonstrated, together with its influence on the resulting SERS activity.

Transparent Composite Films Showing Durable Antifogging and Repeatable Self-Healing Properties Based on an Integral Blend Method

Antifogging coatings for infrastructures and transparent objects have attracted much attention lately from the perspective of safety and visibility. We have developed a one-pot process to fabricate transparent composite films showing long-lasting antifogging and fast repeatable self-healing properties based on an integral blend (IB) method. This method does not require any specific pretreatments of inorganic fillers/particles. Thus, the precursor solutions could be prepared in a single step by simply mixing raw materials, e.g., poly(vinylpyrrolidone) (PVP) having different molecular weights (MWs: 55, 360, and 1300 k), nano-clay particles (NCPs), and amino-terminated organosilane (AOS). In this study, to control the degree of cross-linking between the PVP matrices and NCPs, addition of AOS as a cross-linker to the PVP matrices (weight percentage of AOS to the PVP matrices, α = 0.01-300%) was carefully controlled. Transparency and self-healing abilities/kinetics of the resulting samples were found to be strongly influenced by both the MWs of PVP and α values. Samples spin-coated with the lowest M_W of PVP (55 k) and α values of 0.01-1% gave highly transparent and durable antifogging performance. For example, no fogging was observed for 7 days under >80% relative humidity, and scratches about 30 μm in width could be completely self-healed within a few hours. However, samples with α > 10% gave opaque/grayish films that did not show any self-healing abilities because of an increase in cross-linking of the matrices. The optimized precursor solution was also deposited directly onto the glass slides covered with a transparent porous silica nano-framework (SNF) by a spray-coating method. Due to the formation of the hard and superhydrophilic/hygroscopic SNF with a large surface area, durability of antifogging and self-healing properties of the composite films were moderately improved, compared to those on the flat glass slides.

Optimized antibody immobilization on natural silica-based nanostructures for the selective detection of E. coli

This study reports for the first time the surface modification of fluorescent nanoparticles derived from geothermal silica precipitate with Escherichia coli (E. coli) antibody. The immobilization of biomolecules on the inorganic surface has been carried out using two different pathways, namely the silanization and hydrosilylation reactions. The former applied (3-aminopropyl)triethoxysilane (APTES) as the crosslinker, while the latter used N-hydroxysuccinimide coupled with N-ethyl-N′-(3-dimethyl aminopropyl) carbodiimide hydrochloride (EDC/NHS). Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy with energy dispersive X-ray spectroscopy (FESEM-EDX), and fluorescence spectroscopy were used to confirm the chemical, physical, and optical properties of the surface-modified fluorescent silica nanoparticles (FSNPs). Based on the results of the FTIR, fluorescence spectroscopy and stability tests, the modified FSNPs with EDC/NHS with a ratio of 4 : 1 were proven to provide the optimum results for further conjugation with antibodies, affording the FSNP-Ab2 sample. The FSNP-Ab2 sample was further tested as a nanoplatform for the fluorescence-quenching detection of E. coli, which provided a linear range of 10² to 10⁷ CFU mL⁻¹ for E. coli with a limit of detection (LoD) of 1.6 × 10² CFU mL⁻¹. The selectivity of the biosensor was observed to be excellent for E. coli compared to that for P. aeruginosa and S. typhimurium, with reductions in the maximum fluorescence intensity at 588 nm of 89.22%, 26.23%, and 54.06%, respectively. The inorganic nanostructure–biomolecule conjugation with optimized coupling agents showed promising analytical performance as a selective nanoplatform for detecting E. coli bacteria.

This work describes for the first time the surface modification of natural-based fluorescent nanoparticles with antibodies as optical biosensing platforms.

Remote-controllable and encryptable smart glasses: a photoresponsive azobenzene molecular commander determines the molecular alignments of liquid crystal soldiers

For the development of optically encryptable smart glass that can control the molecular alignment of liquid crystals (LCs), an azobenzene-based reactive molecule (ARM) capable of trans-cis photoisomerization is newly designed and synthesized. Photo-triggered LC-commandable smart glasses are successfully constructed by the surface functionalization technique using 3-aminopropyltriethoxysilane (APTMS) coupling agent and an ARM. The surface functionalization with the ARM is verified by spectroscopic analysis and various observations including changes in the wettability and surface morphology. Using the ARM-treated substrate, the LC command cell which can effectively switch the molecular orientation of nematic LC (E7) by the irradiation of UV and visible light is demonstrated. The results of optical investigation demonstrate the directional correlation between light and photoisomerization, revealing the tilt mechanism of azobenzene units. The capability to control the molecular orientation of LCs remotely and selectively allows the development of remote-controllable and encryptable smart glasses.

Optical Microfiber with a Gold Nanorods-Black Phosphorous Nanointerface: An Ultrasensitive Biosensor and Nanotherapy Platform

The detection and therapy of cancers in the early stage significantly alleviate the associated dangers. Optical devices offer new opportunities for these early measures. However, the clinical translation of the existing methods is severely hindered by their relatively low sensitivity or unclear physiological metabolism. Here, an optical microfiber sensor with a drug loading gold nanorod-black phosphorous nanointerface, as an ultrasensitive biosensor and nanotherapy platform, is developed to meet the early-stage requirement. With interface sensitization and functionalization of the hybrid nanointerface, the microfiber sensor presents an ultrahigh sensing performance, achieving the selective detection of the HER2 biomarker with limits of detection of 0.66 aM in buffer solution and 0.77 aM in 10% serum. It can also distinguish breast cancer cells from other cells in the early stage. Additionally, enabled by the interface, the optical microfiber is able to realize cellular nanotherapy, including photothermal/chemotherapy with pump laser coupling after diagnosis, and evaluate therapy results in real time. The immobilization of the interface on the optical microfiber surface prevents the damage to normal cells induced by nanomaterial enrichment, making the device more efficient and intelligent. This study opens up a new avenue for the development of smart optical platforms for sensitive biosensing and precision therapy.

Assessment of nanoparticle immersion depth at liquid interfaces from chemically equivalent macroscopic surfaces

HYPOTHESIS

We test whether the wettability of nanoparticles (NPs) straddling at an air/water surface or oil/water interface can be extrapolated from sessile drop-derived macroscopic contact angles (mCAs) on planar substrates, assuming that both the nanoparticles and the macroscopic substrates are chemically equivalent and feature the same electrokinetic potential.

EXPERIMENTS

Pure silica (SiO₂) and amino-terminated silica (APTES-SiO₂) NPs are compared to macroscopic surfaces with extremely low roughness (root mean square [RMS] roughness ≤ 2 nm) or a roughness determined by a close-packed layer of NPs (RMS roughness ∼ 35 nm). Equivalence of the surface chemistry is assessed by comparing the electrokinetic potentials of the NPs via electrophoretic light scattering and of the macroscopic substrates via streaming current analysis. The wettability of the macroscopic substrates is obtained from advancing (ACAs) and receding contact angles (RCAs) and in situ synchrotron X-ray reflectivity (XRR) provided by the NP wettability at the liquid interfaces.

FINDINGS

Generally, the RCA on smooth surfaces provides a good estimate of NP wetting properties. However, mCAs alone cannot predict adsorption barriers that prevent NP segregation to the interface, as is the case with the pure SiO₂ nanoparticles. This strategy greatly facilitates assessing the wetting properties of NPs for applications such as emulsion formulation, flotation, or water remediation.

Synthesis of nanostructured protein-mineral-microcapsules by sonication

We propose a simple and eco-friendly method for the formation of composite protein-mineral-microcapsules induced by ultrasound treatment. Protein- and nanoparticle-stabilized oil-in-water (O/W) emulsions loaded with different oils are prepared using high-intensity ultrasound. The formation of thin composite mineral proteinaceous shells is realized with various types of nanoparticles, which are pre-modified with Bovine Serum Albumin (BSA) and subsequently characterized by EDX, TGA, zeta potential measurements and Raman spectroscopy. Cryo-SEM and EDX mapping visualizations show the homogeneous distribution of the densely packed nanoparticles in the capsule shell. In contrast to the results reported in our previous paper,¹ the shell of those nanostructured composite microcapsules is not cross-linked by the intermolecular disulfide bonds between BSA molecules. Instead, a Pickering-Emulsion formation takes place because of the amphiphilicity-driven spontaneous attachment of the BSA-modified nanoparticles at the oil/water interface. Using colloidal particles for the formation of the shell of the microcapsules, in our case silica, hydroxyapatite and calcium carbonate nanoparticles, is promising for the creation of new functional materials. The nanoparticulate building blocks of the composite shell with different chemical, physical or morphological properties can contribute to additional, sometimes even multiple, features of the resulting capsules. Microcapsules with shells of densely packed nanoparticles could find interesting applications in pharmaceutical science, cosmetics or in food technology.

Magnetic Mesoporous Silica Nanorods Loaded with Ceria and Functionalized with Fluorophores for Multimodal Imaging

Multifunctional magnetic nanocomposites based on mesoporous silica have a wide range of potential applications in catalysis, biomedicine, or sensing. Such particles combine responsiveness to external magnetic fields with other functionalities endowed by the agents loaded inside the pores or conjugated to the particle surface. Different applications might benefit from specific particle morphologies. In the case of biomedical applications, mesoporous silica nanospheres have been extensively studied while nanorods, with a more challenging preparation, have attracted much less attention despite the positive impact on the therapeutic performance shown by seminal studies. Here, we report on a sol-gel synthesis of mesoporous rodlike silica particles of two distinct lengths (1.4 and 0.9 μm) and aspect ratios (4.7 and 2.2) using Pluronic P123 as a structure-directing template and rendering ∼1 g of rods per batch. Iron oxide nanoparticles have been synthesized within the pores yielding maghemite (γ-Fe₂O₃) nanocrystals of elongated shape (∼7 nm × 5 nm) with a [110] preferential orientation along the rod axis and a superparamagnetic character. The performance of the rods as T₂-weighted MRI contrast agents has also been confirmed. In a subsequent step, the mesoporous silica rods were loaded with a cerium compound and their surface was functionalized with fluorophores (fluorescamine and Cyanine5) emitting at λ = 525 and 730 nm, respectively, thus highlighting the possibility of multiple imaging modalities. The biocompatibility of the rods was evaluated in vitro in a zebrafish (Danio rerio) liver cell line (ZFL), with results showing that neither long nor short rods with magnetic particles caused cytotoxicity in ZFL cells for concentrations up to 50 μg/ml. We advocate that such nanocomposites can find applications in medical imaging and therapy, where the influence of shape on performance can be also assessed.

Amphiphilic Janus Microspheres Prepared by Caged Photoactivatable Alkoxysilane

A simple photolysis route was proposed to prepare Amphiphilic Janus Particles (AJP) based on SiO2 microspheres. The surface of SiO2 microspheres were modified by photoactive alkoxysilane, which was synthesized by dealcoholization condensation of 6-nitroveratroyloxycarbonyl and isocyanatopropyl-triethoxysilane. UV irradiation caused eater-breaking allowed for the precise control of hydrophilic modification of the hemispherical exposed particles surfaces. The component and morphology of the obtained particles were characterized by fourier transform infrared spectroscopy and ultraviolet-visible spectroscopy, and the Janus feature was evaluated by scanning electron microscopy, transmission electron microscopy, and dispersity in the oil–water dual-phases. The following results were obtained. The AJP with 450 nm size processes the hydrophilic amino groups on one side and the hydrophobic 6-nitroveratryloxycarbonyl moieties on the other. Additionally, the AJP were located at the phase boundary between water and n-hexane, and the negative charged gold nanoparticles with 25 nm size were adsorbed only onto the side with the positive charged amino groups. The AJP have interfacial adsorption energies that can be as much as three times larger than that of homogeneous particles and thus exhibit excellent surface activities.

Impacts of horseradish peroxidase immobilization onto functionalized superparamagnetic iron oxide nanoparticles as a biocatalyst for dye degradation

To enhance the dye removal efficiency by natural enzyme, horseradish peroxidase (HRP) was immobilized onto amine-functionalized superparamagnetic iron oxide and used as a biocatalyst for the oxidative degradation of acid black-HC dye. The anchored enzyme was characterized by vibrating sample magnetometry, Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetry, scanning electron microscopy, Brunauer-Emmett-Teller and Barrett-Joyner-Halenda methods, nitrogen adsorption-desorption measurements, Zeta potential, energy dispersive X-ray spectroscopy, and transmission electron microscopy. The Michaelis constant values of free and immobilized HRP were determined to be 4.5 and 5 mM for hydrogen peroxide and 12.5 and 10 mM for guaiacol, respectively. Moreover, the maximum values of free and immobilized HRP were 2.4 and 2 U for H₂O₂, respectively, and 1.25 U for guaiacol. The immobilized enzyme was thermally stable up to 60°C, whereas the free peroxidase was stable only up to 40°C. In the catalytic experiment, the immobilized HRP exhibited superior catalytic activity compared with that of free HRP for the oxidative decolorization and removal of acid black-HC dye. The influence of experimental parameters such as the catalyst dosage, pH, H₂O₂ concentration, and temperature on the removal efficiency was investigated. The reaction followed second-order kinetics, and the thermodynamic activation parameters were determined.

Single-Conidium Encapsulation in Oil-in-Water Pickering Emulsions at High Encapsulation Yield

This study presents an individual encapsulation of fungal conidia in an oil-in-water Pickering emulsion at a single-conidium encapsulation yield of 44%. The single-conidium encapsulation yield was characterized by analysis of confocal microscopy micrographs. Mineral oil-in-water emulsions stabilized by amine-functionalized titania dioxide (TiO₂-NH₂ or titania-NH₂) particles were prepared. The structure and the stability of the emulsions were investigated at different compositions by confocal microscopy and a LUMiSizer^® respectively. The most stable emulsions with a droplet size suitable for single-conidium encapsulation were further studied for their individual encapsulation capabilities. The yields of individual encapsulation in the emulsions; i.e., the number of conidia that were individually encapsulated out of the total number of conidia, were characterized by confocal microscopy assay. This rapid, easy to use approach to single-conidium encapsulation, which generates a significantly high yield with eco-friendly titania-based emulsions, only requires commonly used emulsification and agitation methods.

Controlled Growth of Organosilane Micropatterns on Hydrophilic and Hydrophobic Surfaces Templated by Vacuum Ultraviolet Photolithography

In this report, micropatterns of (3-aminopropyl)trimethoxysilane (APTMS) were developed on hydrophilic and hydrophobic surfaces after patterning using 172 nm vacuum ultraviolet (VUV) photolithography. Self-assembled monolayers (SAMs) formed on Si substrates through UV hydrosilylation of 1-hexadecene (HD) and 10-undecenoic acid (UDA) were used as hydrophilic and hydrophobic surfaces, respectively. For templating the HD- and UDA-SAMs, the VUV light was exposed to HD- and UDA-SAMs from the slits of photomasks in atmospheric and evacuated environments, respectively. Various oxygenated groups were generated at the exposed domains of HD-SAM, while the COOH groups were trimmed from the irradiated domains of UDA-SAM. The APTMS molecules were immobilized on the domains that were terminated by oxygenated groups after chemical vapor deposition (CVD). The thicknesses of the developed APTMS micropatterns increased significantly by raising the CVD temperature and in the presence of ambient air in the CVD Teflon container as well. The increase in thicknesses was ascribed to the formation of APTMS multilayers, which were mediated by H₃N⁺ ions. Also, the developed APTMS micropatterns on the UDA-SAM patterned by VUV light irradiation in a high-vacuum environment (HV-VUV) were thicker than those on the VUV/(O) patterned HD-SAM due to the presence of inactive oxygenated groups at the surface of VUV/(O)-terminated domains of HD-SAM such as COO-C and C-O-C groups. The presence of water or ambient air facilitated the silane coupling between the silyl groups with the oxygenated and amino groups The combination of VUV photolithography and the CVD method with control of the conditions would enable us to control the thicknesses and shapes of the developed APTMS micropatterns. These findings illustrate the applicability of VUV photolithography for templating hydrophobic and hydrophobic surfaces toward the development of organosilane architectures, which can be feasible for several applications.

Review on Interfacial Bonding Mechanism of Functional Polymer Coating on Glass in Atomistic Modeling Perspective

Atomistic modeling methods are successfully applied to understand interfacial interaction in nanoscale size and analyze adhesion mechanism in the organic-inorganic interface. In this paper, we review recent representative atomistic simulation works, focusing on the interfacial bonding, adhesion strength, and failure behavior between polymer film and silicate glass. The simulation works are described under two categories, namely non-bonded and bonded interaction. In the works for non-bonded interaction, three main interactions, namely van der Waals interaction, polar interaction, and hydrogen bonds, are investigated, and the contributions to interfacial adhesion energy are analyzed. It is revealed that the most dominant interaction for adhesion is hydrogen bonding, but flexibility of the polymer film and modes of adhesion measurement test do affect adhesion and failure behavior. In the case of bonded interactions, the mechanism of covalent silane bond formation through condensation and hydrolysis process is reviewed, and surface reactivity, molecular density, and adhesion properties are calculated with an example of silane functionalized polymer. Besides interfacial interactions, effects of external conditions, such as surface morphology of the glass substrate and relative humidity on the adhesion and failure behavior, are presented, and modeling techniques developed for building interfacial system and calculating adhesion strengths are briefly introduced.

Single cell encapsulation in a Pickering emulsion stabilized by TiO2 nanoparticles provides protection against UV radiation for a biopesticide

A new formulation for biological pest control with significant UV protection capability has been developed in this research. The formulation is based on individual encapsulation of fungal conidia in an oil/water Pickering emulsion. The droplets size of the emulsions was tuned to meet the demands of single conidia encapsulation in the oil droplets. The emulsions are stabilized by amine-functionalized TiO₂ (titania) nanoparticles (NPs). The droplet size, stability, and structure of the emulsions were investigated at different TiO₂ contents and oil/water phase ratios. Most of the emulsions remained stable for 6 months. The structural properties of the Pickering emulsions were characterized by confocal microscopy and high-resolution cryogenic scanning electron microscopy (cryo-HRSEM). The presence of the TiO₂ particles at the interface was confirmed by both confocal microscopy and cryo-HRSEM. Metarhizium brunneum-7 (Mb7) conidia were added to the emulsions. The successful encapsulation of individual conidia in the oil droplets was confirmed by confocal microscopy. The individual encapsulation of the conidia in the emulsions was significantly improved by dispersing the conidia in a 0.02 % Triton X-100 solution prior to emulsification. In addition, the bioassay results have shown, that exposure of the encapsulated conidia to natural UV light did not change their germination rates, however, the unprotected conidia demonstrated a dramatic decrease in their germination rates. These results confirm the UV protection capability of the studied emulsions.

Core-shell structured SiO2@ZrO2@SiO2 filler for radiopacity and ultra-low shrinkage dental composite resins

To overcome the interfacial problem between X-ray radiopaque ZrO₂ fillers and polymer resin in dental composites, monodispersed SiO₂@ZrO₂@SiO₂ (SZS) microspheres with narrow size distribution were prepared by a controlled sol-gel method. In the presence of SiO₂ coating layer over SiO₂@ZrO₂ (SZ) microspheres, they were easily silanized same as SiO₂ microspheres. Ethoxylated bisphenol A dimethacrylate (EBPADMA) with a higher molecular weight and a lower viscosity was used as base resin monomer mixed with a low amount of diluent triethylene glycol dimethacrylate (TEGDMA). Additionally, the addition of a small amount of pore agent acetone dicarboxylic acid (ADCA) produced some voids, thereby effectively reducing the polymerization shrinkage of the resin. The prepared dental composites combining 52 wt% monodispersed silica microsphere, 20 wt% SZS microspheres, exhibited significantly enhanced capacity in radiopacity (higher than tooth enamel) and very low shrinkage (<0.1%). It also has better mechanical properties than resin composites filled with SiO₂ microspheres, and its strength can meet practical applications. The properties of the radiopaque dental composite were to be further tuned by varying the amount of SZS microspheres contents, and the radiopaque resin has an advantage over the commercial one in that it is clinically nondestructive.

pH-Responsive Ultrathin Nanoporous SiO2 Films for Selective Ion Permeation

Ultrathin nanoporous (NP) films are an emerging field for selective and effective ion/molecular separation and electrochemical sensing applications. We describe selective ion permeation in surface-functionalized ultrathin NP SiO₂ films (NP SiO₂-NH₂). The ultrathin NP SiO₂ films with ca. 8 nm thickness were prepared from silsesquioxane-containing blend polymer Langmuir-Blodgett films (nanosheets) using the photo-oxidation method. The porous SiO₂ surface was modified with a pH-responsive amine-containing silane coupling agent. Selective ion permeation was demonstrated under acidic pH conditions (pH ≤ 6) using two equally sized redox probes: negative (Fe(CN)₆^3-/4-) and positive (Ru(NH₃)₆^2+/3+) ions. The current density for Fe(CN)₆^3-/4- decreased as the pH value increased to pH = 6, whereas it increased for Ru(NH₃)₆^2+/3+. Control measurements revealed that the probes can penetrate the pores of nonfunctionalized SiO₂ films irrespective of pH values, indicating that both the size and the surface charge response contributed to selective ion permeation. Results obtained from this study pave the way for new applications in molecular separation and sensing applications based on ultrathin nanoporous films (<10 nm) and tailored surfaces.

Ionic liquid stationary phase coating optimization for semi-packed microfabricated columns

This work highlights the effect of the stationary phase coating process on the separation efficiency of gas chromatography microcolumns. The stationary phase coating quality was characterized by three different bis(trifluoromethylsulfonyl)imide (NTf₂) anion based ionic liquids. The ionic liquids containing NTf₂ anion are used for gas chromatography due to their high temperature stability. In this work, the chemical and physical approaches of column deactivation as well as the temperature treatment were evaluated by separating a mixture of 20 organic components and saturated alkanes. The results show that higher oven temperature treatment provides higher efficiency while losing a bit of peak symmetry. The thermal treated 1-butylpyridinum bis(trifluoromethylsulfonyl) imide [BPY][NTf₂] stationary phase at 240°C demonstrated as high as 8300 plates per meter for naphthalene. This was a 5-fold increase in separation efficiency in comparison to those of the columns treated at 200°C. Albeit being within acceptable ranges, the peak tailing degraded from 1.17 to 1.46 for naphthalene when the processing temperature for coating increased. Both chemical and physical deactivation process increased separation efficiencies and peak resolution.

Silane-Coating Strategy for Titanium Functionalization Does Not Impair Osteogenesis In Vivo

Silane-coating strategy has been used to bind biological compounds to the titanium surface, thereby making implant devices biologically active. However, it has not been determined if the presence of the silane coating itself is biocompatible to osseointegration. The aim of the present study was to evaluate if silane-coating affects bone formation on titanium using a rabbit model. For this, titanium screw implants (3.75 by 6 mm) were hydroxylated in a solution of H₂SO₄/30% H₂O₂ for 4 h before silane-coating with 3-aminopropyltriethoxysilane (APTES). A parallel set of titanium screws underwent only the hydroxylation process to present similar acid-etched topography as a control. The presence of the silane on the surface was checked by x-ray photoelectron spectroscopy (XPS), with scanning electron microscopy (SEM) and atomic force microscopy (AFM). A total of 40 titanium screws were implanted in the tibia of ten New Zealand rabbits in order to evaluate bone-to-implant contact (BIC) after 3 weeks and 6 weeks of healing. Silane-coated surface presented higher nitrogen content in the XPS analysis, while micro- and nano-topography of the surface remained unaffected. No difference between the groups was observed after 3 and 6 weeks of healing (p > 0.05, independent t-test), although an increase in BIC occurred over time. These results indicate that silanization of a titanium surface with APTES did not impair the bone formation, indicating that this can be a reliable tool to anchor osteogenic molecules on the surface of implant devices.

Optimizing glass-ceramic bonding incorporating new silane technology in an experimental universal adhesive formulation

OBJECTIVE

Incorporating silane-coupling agent into universal adhesives (UAs) to simplify adhesive luting of glass-ceramic restorations appeared ineffective due to silane's instability in an acidic aqueous solution. This study aimed to evaluate new silane technology added to an experimental UA to be bonded to glass ceramics without separate prior silanization.

METHODS

Combined silane technology, consisting of 3-(aminopropyl)triethoxysilane (APTES) and γ-methacryloxypropyltriethoxysilane (γMPTES), was incorporated into an experimental UA formulation, being referred to as ADH-XTE (3M Oral Care). Immediate and aged shear bond strength (SBS) of ADH-XTE onto as-milled ('AM'), tribochemical silica-coated ('TSC'), HF-etched ('HF'), and mirror-polished ('MP') glass-ceramic CAD/CAM blocks (IPS e.max CAD) with/without separate silanization was measured (n = 10/group). The control adhesives included Scotchbond Universal ('SBU') and Scotchbond 1 XT ('SB1-XT'). The glass-ceramic surface topography and the fractography of the SBS-debonded specimens were observed by SEM.

RESULTS

Without separate prior silanization, the experimental UA ADH-XTE, containing combined APTES/γMPTES silane technology, significantly outperformed the glass-ceramic bonding efficiency of its silane-containing SBU precursor, while it performed equally effective as SBU applied with prior silanization. Upon aging, significant reduction in SBS was recorded when ADH-XTE was bonded to TSC glass-ceramic surfaces (p < 0.05), while not to HF ones. Notably, the lowest SBS was obtained when the UAs were bonded to AM and MP glass-ceramic surfaces, in particular when applied without separate prior silanization (p < 0.05).

SIGNIFICANCE

The glass-ceramic bonding capacity of the new combined APTES/γMPTES silane-containing UA ADH-XTE surpassed that of its SBU precursor. HF etching remains needed to durably bond to glass-ceramics.

3D nanointerface enhanced optical microfiber for real-time detection and sizing of single nanoparticles

Portable devices, which can detect and characterize the individual nanoparticles in real time, are of insignificant interest for early diagnosis, homeland security, semiconductor manufacturing and environmental monitoring. Optical microfibers present a good potential in this field, however, are restricted by the sensitivity limit. This study reports the development of a 3D plasmonic nanointerface, which is made of a Cu-BTC framework supporting Cu_3-xP nanocrystals, enhancing the optical microfiber for real-time detection and sizing of single nanoparticles. The Cu_3-xP nanocrystals are successfully embedded in the 3D Cu-BTC framework. The localized-surface plasmon resonance is tuned to coincide with the evanescent field of the optical microfiber. The 3D Cu-BTC framework, as the scaffold of nanocrystals, confines the local resonance field on the microfiber with three dimensions, at which the binding of target nanoparticles occurs. Based on the evanescent field confinement and surface enhancement by the nanointerface, the optical microfiber sensor overcomes its sensitivity limit, and enables the detection and sizing of the individual nanoparticles. The compact size and low optical power supply of the sensor confirm its suitability as a portable device for the real-time single-nanoparticle characterization, especially for the convenient evaluation of the ultrafine particles in the environment. This work opens up an approach to overcome the sensitivity limit of the optical microfibers, as long with stimulating the portable real-time single-nanoparticle detection and sizing.

Synergistic effect of silane cross-linker (APTEOS) on PVA/gelatin blend films for packaging applications

The objective of this work is to fabricate hydrogel films which are biodegradable and also fit for packaging applications. The hydrogel films were prepared by the reaction of polyvinyl alcohol and gelatin with and without 3-aminopropyltriethoxysilane (APTEOS) cross-linker. The hydrogel films were then characterized by FTIR spectroscopy, degree of swelling, TGA, SEM analysis and mechanical testing. The FTIR spectra of the hydrogel films confirmed the presence of both polymers and hydrogen bonding between them. TGA analysis confirmed the increase in thermal stability with the increase of cross-linker amount. SEM analysis confirmed the increase in uniformity of structure with the increase of cross-linker amount. The increase in cross-linker amount resulted in decrease of degree of swelling and increase of tensile strength. The biodegradability of hydrogel films was evaluated by performing soil burial test and found to be decreased with the increase of cross-linker amount. In order to balance the tensile strength and biodegradability, the optimum amount of cross-linker was determined which resulted in the formation of the best performing film. Finally, our best performing film was compared with other hydrogel films reported in the literature. Hence, the hydrogel films cross-linked with APTEOS are biodegradable, having high tensile strength and suitable for packaging purpose.