Primary and tertiary amines bifunctional graphene oxide for cooperative catalysis

Fabrication of composite transparent conductive electrodes based on silver nanowires

Composite transparent conductive electrodes (C-TCEs) have recently been produced using low-cost techniques to keep up with the boom in the fabrication and development of optoelectronic devices. In this article, silver nanowires (AgNWs) were successfully synthesized by a simple hydrothermal method using different molecular weights MWs of poly (N-vinylpyrrolidone) (PVP). Graphene oxide (GO) was prepared using the modified Hummers' method and a reduction step was held on GO films to produce reduced GO (rGO). C-TCEs were fabricated by over-coating the AgNWs electrodes with rGO, or poly(3,4-ethylenedioxythiophene) polystyrene sulfonate to improve the roughness, surface energy, and sheet resistance. The influence of using lower and higher MWs of PVP on the yield, shape, and size of AgNWs was investigated. The results showed that using lower MW of PVP had a great effect on the yield, morphology, and aspect ratio of AgNWs with diameter of 46 nm and average length 12 µm. The optical, morphological, topographical, and electrical properties of TCEs were studied. AgNWs/rGO composite electrode provided the lowest surface roughness and surface energy of 250 nm and 47.95 mN/m, respectively, with a relatively high transparency of 78.2% at 550 nm light wavelength, and a low sheet resistance of 27 Ω/□.

Gram-Scale Room-Temperature Synthesis of Solid-State Fluorescent Carbon Nanodots for Bright Electroluminescent Light Emitting Diodes

The reaction conditions of high temperature and high pressure will introduce structural defects, high energy consumption, and security risks, severely hindering the industrial application of organic carbon nanodots (CDs). Moreover, the aggregation caused quenching effect also fundamentally limits the CDs based electroluminescent light emitting diodes (LEDs). Herein, for the first time, a rapid one-step room temperature synthetic strategy is introduced to prepare highly emissive solid-state-fluorescent CDs (RT-CDs). A strong oxidizing agent, potassium periodate (KIO₄ ), is adopted as a catalyst to facilitate the cyclization of o-phenylenediamine and 4-dimethylamino phenol in aqueous solution at room temperature for only 5 min. The resultant organic molecule, 2-(dimethylamino) phenazine, will self-assemble kinetically to generate supramolecular-structure CDs during crystallization. The elaborately arranged supramolecular structure (J aggregates) endows CDs with intense solid-state-fluorescence. Density functional theory (DFT) calculation shows that the excited state of RT-CDs exhibits charge transfer characteristic owing to the unique donor-Π-acceptor structure. A high-performance monochrome RT-CDs based electroluminescent LEDs (2967 cd m^-2 and 1.38 cd A^-1 ) were fabricated via systematic optimizations of device engineering. This work provides a concrete and feasible avenue for the rapid and massive preparation of CDs, advancing the commercialization of CDs based optoelectronic devices.

Induction of zincophore pseudopaline secretion by Cr(VI) and intracellular formation of granules from nanocrystal aggregation by Cr(III) in Pseudomonas aeruginosa

When microorganisms are challenged with toxic metals, intracellular granules are commonly observed, however, the exact nature of these granules is poorly understood. Here we show that when Pseudomonas aeruginosa CCTCC AB93066 were exposed to Cr(VI), Cr can enter the cell in the form of both Cr(VI) and Cr(III), and intracellular granules of several hundred nanometers were formed in the nucleoid region and were built up by aggregation of nanocrystals. We suggested that these nanocrystals are organic crystals. Transcriptomic profiles and liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis indicated that pseudopaline (a metallophore that can complex with Zn²⁺) production and pseudopaline-Zn²⁺ import into bacterial cells were enhanced upon Cr(VI) exposure. It was proposed that pseudopaline can scavenge Zn²⁺ which is essential for transcription alteration and DNA repair. Excessive pseudopaline might precipitate as nanospheres in the nuclear region that are further agglomerated by Cr(III) to form larger granules. During this process, Cr(III) is sequestered and immobilized. Hence we revealed pseudopaline production and zinc acquisition is crucial for alleviation of Cr(VI) toxicity and intracellular granules are composed of organic nanospheres which are aggregated by Cr(III).

Simple fluorescence chemosensor for the detection of calcium ions in water samples and its application in bio-imaging of cancer cells

This article describes the design, synthesis and characterization of a sensor suitable for practical measurement of ionized calcium in water samples and cancer cells. Calcium is an important ion in living organs and works as a messenger in several cellular functions. A lack of Ca ions interrupts the immune system and can lead to several diseases. A novel magnetic-polydopamine nanoparticle (PDNP)/rhodamine B (RhB)/folic acid (FA) nanoparticle was developed for the determination of calcium ions in MCF 7 cell lysates and water samples. Furthermore, the produced nanoparticle was employed for bioimaging of folate receptor (FR)-overexpressed cancer cells. This nanoprobe displayed a bright photoluminescence emission at 576 nm under an excitation wavelength of 420 nm. In the presence of calcium ions, the fluorescence emission of the MNPs-PDNPs/RhB/FA probe was proportionally decreased from 20 ng mL-1 to 100 ng mL-1 and 0.5 μg mL-1 to 20 μg mL-1 with a lower limit of quantification (LLOQ) of about 20 ng mL-1. The developed sensor showed a low-interference manner in the presence of possible coexistence interfering ions. In addition, this nanomaterial showed excellent biocompatibility with favorable differentiation ability to attach to the FR-positive cancer cells. The MNPs-PDNPs/RhB/FA nanoparticle has been utilized for bioimaging of the MCF 7 cell with favorable differentiation ability.

Highly Selective Adsorption of 99TcO4-/ReO4- by a Novel Polyamide-Functionalized Polyacrylamide Polymer Material

The treatment of radioactive wastewater is one of the major problems in the current research. With the development of nuclear energy, the efficient removal of 99TcO4- in radioactive wastewater has attracted the attention of countries all over the world. In this study, a novel functional polyamide polymer p-(Amide)-PAM was synthesized by the two-step method. The experimental results show that p-(Amide)-PAM has good adsorptive properties for 99TcO4-/ReO4- and has good selectivity in the nitric acid system. The kinetics of the reaction of p-(Amide)-PAM with 99TcO4-/ReO4- was studied. The results show that p-(Amide)-PAM has a fast adsorption rate for 99TcO4-/ReO4-, the saturated adsorption capacity reaches 346.02 mg/g, and the material has good reusability. This new polyamide-functionalized polyacrylamide polymer material has good application prospects in the removal of 99TcO4- from radioactive wastewater.

An Update on Graphene Oxide: Applications and Toxicity

Graphene oxide (GO) has attracted much attention in the past few years because of its interesting and promising electrical, thermal, mechanical, and structural properties. These properties can be altered, as GO can be readily functionalized. Brodie synthesized the GO in 1859 by reacting graphite with KClO3 in the presence of fuming HNO3; the reaction took 3-4 days to complete at 333 K. Since then, various schemes have been developed to reduce the reaction time, increase the yield, and minimize the release of toxic byproducts (NO2 and N2O4). The modified Hummers method has been widely accepted to produce GO in bulk. Due to its versatile characteristics, GO has a wide range of applications in different fields like tissue engineering, photocatalysis, catalysis, and biomedical applications. Its porous structure is considered appropriate for tissue and organ regeneration. Various branches of tissue engineering are being extensively explored, such as bone, neural, dentistry, cartilage, and skin tissue engineering. The band gap of GO can be easily tuned, and therefore it has a wide range of photocatalytic applications as well: the degradation of organic contaminants, hydrogen generation, and CO2 reduction, etc. GO could be a potential nanocarrier in drug delivery systems, gene delivery, biological sensing, and antibacterial nanocomposites due to its large surface area and high density, as it is highly functionalized with oxygen-containing functional groups. GO or its composites are found to be toxic to various biological species and as also discussed in this review. It has been observed that superoxide dismutase (SOD) and reactive oxygen species (ROS) levels gradually increase over a period after GO is introduced in the biological systems. Hence, GO at specific concentrations is toxic for various species like earthworms, Chironomus riparius, Zebrafish, etc.

Zwitterionic Graphene Quantum Dots to Stabilize Pickering Emulsions for Controlled-Release Applications

Graphene quantum dots (GQDs) are a subset of the nanocarbon material family, which promise a wide spectrum of applications. Herein, we describe amphiphilic graphene quantum dots with zwitterionic features (ZGQDs), which are able to stabilize the oil/water interface. ZGQDs were fabricated by modifying GQDs with tertiary amine groups and alkyl groups. Moreover, the blocking and unblocking behavior of ZGQDs at the oil/water interface could be tuned by adjusting pH values in the aqueous phase. It would provide a flexible and adjustable method to manipulate interfacial properties of ZGQDs, which enabled a switchable molecular diffusion through a fluid-fluid interface. ZGQDs have shown well-controlled interfacial behavior under different pH conditions, indicating great potential for applications in controlled molecular diffusion based on nanoparticles demonstrated in this work.

Photopatterning of Carbon Dots in Poly(vinyl alcohol) with Photoacid Generators

Carbon dots (CDs) have drawn considerable attention owing to their attractive photoluminescence, advantageous chemical tolerance, good biocompatibility, and so on. However, it remains challenging to tune their photoluminescence spatially and temporally due to their high photostability. Herein, a viable approach to in-situ dialing the photoluminescence of CDs by using light in the presence of a photoacid generator (PAG, e.g., diphenyliodonium hexafluorophosphate) is demonstrated. Fluorescence quenching occurs upon light irradiation due to the protonation of pyridine and amino nitrogen atoms of CDs according to X-ray photoelectron spectroscopy and cyclic voltammetry. As such, blue, green, and red color fluorescent patterns of CDs are ready to form in poly(vinyl alcohol) by light irradiation under photomask. These patterns not only show a controlled preservation time under room light, but also can be erased on demand by flood UV irradiation, which are promising for advanced anti-counterfeiting such as shelf-life based security and erasable encryption.

Covalently grafting first-generation PAMAM dendrimers onto MXenes with self-adsorbed AuNPs for use as a functional nanoplatform for highly sensitive electrochemical biosensing of cTnT

2D MXene-Ti₃C₂T_χ has demonstrated promising application prospects in various fields; however, it fails to function properly in biosensor setups due to restacking and anodic oxidation problems. To expand beyond these existing limitations, an effective strategy to for modifying the MXene by covalently grafting first-generation poly(amidoamine) dendrimers onto an MXene in situ (MXene@PAMAM) was reported herein. When used as a conjugated template, the MXene not only preserved the high conductivity but also conferred a specific 2D architecture and large specific surface areas for anchoring PAMAM. The PAMAM, an efficient spacer and stabilizer, simultaneously suppressed the substantial restacking and oxidation of the MXene, which endowed this hybrid with improved electrochemical performance compared to that of the bare MXene in terms of favorable conductivity and stability under anodic potential. Moreover, the massive amino terminals of PAMAM offer abundant active sites for adsorbing Au nanoparticles (AuNPs). The resulting 3D hierarchical nanoarchitecture, AuNPs/MXene@PAMAM, had advanced structural merits that led to its superior electrochemical performance in biosensing. As a proof of concept, this MXene@PAMAM-based nanobiosensing platform was applied to develop an immunosensor for detecting human cardiac troponin T (cTnT). A fast, sensitive, and highly selective response toward the target in the presence of a [Fe(CN)₆]^3-/4- redox marker was realized, ensuring a wide detection of 0.1-1000 ng/mL with an LOD of 0.069 ng/mL. The sensor's signal only decreased by 4.38% after 3 weeks, demonstrating that it exhibited satisfactory stability and better results than previously reported MXene-based biosensors. This work has potential applicability in the bioanalysis of cTnT and other biomarkers and paves a new path for fabricating high-performance MXenes for biomedical applications and electrochemical engineering.

Construction of direct Z-scheme Bi5O7I/UiO-66-NH2 heterojunction photocatalysts for enhanced degradation of ciprofloxacin: Mechanism insight, pathway analysis and toxicity evaluation

Direct Z-scheme Bi₅O₇I/UiO-66-NH₂ (denoted as BU-x) heterojunction photocatalysts were successfully constructed through ball-milling method. Photocatalytic activities of the as-prepared BU-x samples were determined by using a typical fluoroquinolone antibiotic, ciprofloxacin (CIP). All BU-x heterojunctions exhibited better CIP removal performances than that of pristine Bi₅O₇I and UiO-66-NH₂ upon exposure to white light irradiation. In comparison, the heterojunction with UiO-66-NH₂ content of 50 wt% (BU-5) showed excellent structural stability and the optimal adsorption-photodegradation efficiency for the CIP removal. The removal efficiency of CIP (10 mg/L) over BU-5 (0.75 g/L) achieved 96.1% within 120 min illumination. Meanwhile, the effect of photocatalyst dosage, pH and inorganic anions were systemically explored. Reactive species trapping experiments, electron spin resonance (ESR) signals, Mott-Schottky measurements and density functional theory (DFT) simulation revealed that the photo-generated holes (h⁺), hydroxyl radical (·OH) and superoxide radical (·O₂^-) played crucial roles in CIP degradation. This result can be ascribed to that the unique Z-scheme charge transfer configuration retained the excellent redox capacities of Bi₅O₇I and UiO-66-NH₂. Meanwhile, the CIP degradation pathways and the toxicity of various intermediates were subsequently analyzed. This work provided a feasible idea for removing antibiotics by bismuth-rich bismuth oxyhalide/MOF-based heterostructured photocatalysts.

Facile In Situ Chemical Cross-Linking Gel Polymer Electrolyte, which Confines the Shuttle Effect with High Ionic Conductivity and Li-Ion Transference Number for Quasi-Solid-State Lithium-Sulfur Battery

As a secondary Li-ion battery with high energy density, lithium-sulfur (Li-S) batteries possess high potential development prospects. One of the important ingredients to improve the safety and energy density in Li-S batteries is the solid-state electrolyte. However, the poor ionic conductivity largely limits its application for the commercial market. At present, the gel electrolyte prepared by combining the electrolyte or ionic liquid with the all-solid electrolyte is an effective method to solve the low ion conductivity of the solid electrolyte. We present a cross-linked gel polymer electrolyte with fluoroethylene carbonate (FEC) as a solid electrolyte interface (SEI) film formed for Li-S quasi-solid-state batteries, which can be simply synthesized without initiators. This gel polymer electrolyte with FEC as an additive (GPE@FEC) possesses high ionic conductivity (0.830 × 10^-3 S/cm at 25 °C and 1.577 × 10^-3 S/cm at 85 °C) and extremely high Li-ion transference number (t_Li⁺ = 0.674). In addition, the strong ability toward anchoring polysulfides resulting in the high electrochemical performance of Li-S batteries was confirmed in GPE@FEC by the diffusion experiment, X-ray photoelectron spectroscopy analysis (XPS), and scanning electron microscopy (SEM) mapping of the S element. Such a high ion conductivity (IC) gel polymer electrolyte enables a competitive specific capacity of 940 mAh/g at 0.2C and supreme cycling performance for 180 cycles at 0.5C, which is far beyond that of conventional poly(ethylene oxide)-based quasi-solid-state Li-S batteries.

Green Conversion of CO2 and Propargylamines Triggered by Triply Synergistic Catalytic Effects in Metal-Organic Frameworks

Cyclization of propargylamines with CO₂ to obtain 2-oxazolidone heterocyclic compounds is an essential reaction in industry but it is usually catalyzed by noble-metal catalysts with organic bases as co-catalysts under harsh conditions. We have synthesized a unique Cu^I /Cu^II mixed valence copper-based framework {[(Cu^I ₆ I₅ )Cu₃ ^II L₆ (DMA)₃ ](NO₃ )⋅9DMA}_n (1) with good solvent and thermal stability, as well as a high density of uncoordinated amino groups evenly distributed in the large nanoscopic channels. Catalytic experiments show that 1 can effectively catalyze the reaction of propargylamines with CO₂ , and the yield can reach 99 %. The turnover frequency (TOF) reaches a record value of 230 h^-1 , which is much higher than that of reported noble-metal catalysts. Importantly, this is the first report of heterogeneously catalyzed green conversion of propargylamines with CO₂ without solvents and co-catalysts under low temperature and atmospheric pressure. A mechanistic study reveals that a triply synergistic catalytic effect between Cu^I /Cu^II and uncoordinated amino groups promotes highly efficient and green conversion of CO₂ . Furthermore, 1 directly catalyzes this reaction with high efficiency when using simulated flue gas as a CO₂ source.

TETA-anchored graphene oxide enhanced polyamide thin film nanofiltration membrane for water purification; performance and antifouling properties

This work investigates the performance and structure of polyamide thin film nanocomposite (PA-TFN) membrane incorporated with triethylenetetramine-modified graphene oxide (GO-TETA). The embedment of GO-TETA nanosheets within the structure of PA-TFN membrane was evaluated at different concentrations (0.005, 0.01, 0.03 wt%; in aqueous piperazine (PIP)) through interfacial polymerization (IP). The physicochemical properties of the prepared membrane were investigated by SEM, AFM, water contact angle, and zeta potential as well as ATR-IR spectroscopy. The presence of longer chains of amino groups (in comparison with the directly linked amino ones) among the stacked GO nanosheets was assumed to increase interlayer spacing, resulting in remarkable changes in water permeance and separation behavior of modified polyamide (PA) membrane. It is seen that GO-TETA nanosheets were uniformly distributed in the matrix of PA layer. With increasing the concentration of GO-TETA, the flux of TFN membranes under 6 bar was increased from 49.8 l/m² h (no additive) to 73.2 l/m² h (TFN comprising 0.03 wt% GO-TETA. In addition, more loading GO-TETA resulted in a significant decrease in the average thickness of the polyamide layer from ~380 to ~150 nm. Furthermore, addition of GO-TETA improved the hydrophilicity of nanocomposite membranes, resulting in superb water flux recovery (antifouling indicator) as high as 95% after filtration of bovine serum albumin solution. Also, the retention capability of the TFN membranes towards some textile dyes increased as high as 99.6%.

Influence of Reduced Graphene Oxide on the Electropolymerization of 5-amino-1-naphthol and the Interaction of 1,4-phenylene Diisothiocyanate with the Poly(5-amino-1-naphtol)/Reduced Graphene Oxide Composite

A new composite base on reduced graphene oxide (RGO) and poly(5-amino-1-naphthol) (P5A1N) was synthesized by the electrochemical polymerization of 5-amino-1-naphthol (5A1N) in the presence of HClO₄ and H₄SiW₁₂O₄₀ onto the surface of Au electrode covered with the RGO sheets. The linear dependence of the current densities of the anodic and cathodic peaks with the scan rate of the potential range (0; 0.8) V vs. SCE, reported during electropolymerization of 5A1N, indicates an electron transfer that is controlled by diffusion. A covalent functionalization of the RGO sheets with P5A1N is argued by: (i) the simultaneous disappearance of the IR band at 1584 cm^-1 and the appearance of the new IR bands at 812, 976 and 3744 cm^-1, and (ii) the appearance of two Raman lines at 738 and 1428 cm^-1. An application of the RGO sheets covalently functionalized with P5A1N is demonstrated to support 1,4-phenylene diisothiocyanate (PDITC), a compound used as a cross-linking agent for various biological applications. The chemical adsorption of PDITC onto the RGO sheets covalently functionalized with P5A1N, which involves the appearance of new functional groups of the type thiourea, was proven by Raman scattering and IR spectroscopy.

Reversible Oxygen Sensing Based on Multi-Emission Fluorescence Quenching

Oxygen is ubiquitous in nature and it plays a key role in several biological processes, such as cellular respiration and food deterioration, to name a few. Currently, reversible and non-destructive oxygen sensing is usually performed with sensors produced by photosensitization of phosphorescent organometallic complexes. In contrast, we propose a novel route of optical oxygen sensing by fluorescence-based quenching of oxygen. We hereby developed for the first time a set of multi-emissive purely organic emitters. These were produced through a one-pot hydrothermal synthesis using p-phenylenediamine (PPD) and urea as starting materials. The origin of the multi-emission has been ascribed to the diversity of chemical structures produced as a result of oxidative oligomerization of PPD. A Bandrowski's base (BB, i.e., trimer of PPD) is reported as the main component at reaction times higher than 8 h. This indication was confirmed by electrospray-ionization quadrupole time-of-flight (ESI-QTOF) and liquid chromatography-mass spectrometry (LC-MS) analysis. Once the emitters are embedded within a high molecular weight poly (vinyl alcohol) matrix, the intensities of all three emission centers exhibit a non-linear quenching provoked by oxygen within the range of 0-8 kPa. The detection limit of the emission centers are 0.89 kPa, 0.67 kPa and 0.75 kPa, respectively. This oxygen-dependent change in fluorescence emission is reversible (up to three tested 0-21% O₂ cycles) and reproducible with negligible cross-interference to humidity. The cost-effectiveness, metal-free formulation, cross-referencing between each single emission center and the relevant oxygen range are all appealing features, making these sensors promising for the detection of oxygen, e.g., in food packaged products.

Enhanced performance of lithium–sulfur batteries based on single-sided chemical tailoring, and organosiloxane grafted PP separator

Even after a decade of research and rapid development of lithium–sulfur (Li–S) batteries, the infamous shuttle effect of lithium polysulfide is still the major challenge hindering the commercialization of Li–S batteries. In order to further address this issue, a functionalized PP separator is obtained through selective single-sided chemical tailoring, and then organosiloxane fumigation grafting. During the charge–discharge process, the grafted functional groups can effectively block the transportation of the dissolved polysulfides through strong chemical anchoring, inhibit the shuttle effect and greatly enhance the cycle stability of the Li–S battery. Interestingly, the specially designed single-sided enlarged channel structure formed by chemical tailoring can well accommodate the deposition with intermediate polysulfides on the separator surface toward the cathode chamber, resulting in enhanced initial discharge capacity and rate performance. Compared to the battery assembled with PP, the Li–S battery employing the separator grafted with a 3-ureidopropyltrimethoxysilane (PP–O^x−–U) displays better electrochemical performance. Even at 2C, it can still deliver a high capacity of 786 mA h g⁻¹, and retain a capacity of 410 mA h g⁻¹ with a low capacity fading of 0.095% per cycle over 500 cycles. This work provides a very promising and feasible strategy for the development of a special functionalization PP separator for Li–S batteries with high electrochemical performance.

Even after a decade of research and rapid development of lithium–sulfur (Li–S) batteries, the infamous shuttle effect of lithium polysulfide is still the major challenge hindering the commercialization of Li–S batteries.

Multi-responsive nanocomposite membranes of cellulose nanocrystals and poly(N-isopropyl acrylamide) with tunable chiral nematic structures

By imitating the unique structure of nature creatures, photonic membranes with periodic chiral helical structure can be assembled by cellulose nanocrystals (CNCs). It is still an issue to fabricate CNC photonic structures tunable in the entire visible spectrum with multiple stimuli-response capacities. Herein, a multi-responsive nanocomposite photonic membrane is fabricated by co-assembly of poly(N-isopropyl acrylamide) (PNIPAM) grafted CNCs with waterborne polyurethane (WPU) latex on the basis of the chiral nematic structure of CNCs, the thermo-responsibility of PNIPAM, and the flexibility of WPU. The flexible photonic membranes with uniform structural colors from blue to red are obtained by tuning the PNIPAM content. The membrane exhibits reversible responses to solvents, and iridescence changes in response to relative humidity with excellent repeatability. Interestingly, the membrane can be transparent or opaque depending on the ambient temperature. The photonic membranes are appealing in applications as humidity sensor, camouflage materials, and even smart windows.

Rechargeable Zinc-Air Battery with Ultrahigh Power Density Based on Uniform N, Co Codoped Carbon Nanospheres

Highly efficient catalysts for both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are key to the commercialization of rechargeable zinc-air batteries (ZABs). In this work, a catalyst with uniform nanospherical morphology was prepared from cobalt nitrate, acetylacetone, and hydrazine hydrate. The final catalyst possesses high ORR and OER performances, with a half-wave potential of 0.911 V [vs reversible hydrogen electrode (RHE)] for ORR and a low potential of 1.57 V (vs RHE) at 10 mA cm^-2 for OER in 0.1 M KOH solution. Specially, a ZAB based on the catalyst demonstrates an ultrahigh power density of 479.1 mW cm^-2, as well as excellent stability, and potential in practical applications.

Electroluminescent Warm White Light-Emitting Diodes Based on Passivation Enabled Bright Red Bandgap Emission Carbon Quantum Dots

The development of efficient red bandgap emission carbon quantum dots (CQDs) for realizing high-performance electroluminescent warm white light-emitting diodes (warm-WLEDs) represents a grand challenge. Here, the synthesis of three red-emissive electron-donating group passivated CQDs (R-EGP-CQDs): R-EGP-CQDs-NMe2, -NEt2, and -NPr2 is reported. The R-EGP-CQDs, well soluble in common organic solvents, display bright red bandgap emission at 637, 642, and 645 nm, respectively, reaching the highest photoluminescence quantum yield (QY) up to 86.0% in ethanol. Theoretical investigations reveal that the red bandgap emission originates from the rigid π-conjugated skeleton structure, and the -NMe2, -NEt2, and -NPr2 passivation plays a key role in inducing charge transfer excited state in the π-conjugated structure to afford the high QY. Solution-processed electroluminescent warm-WLEDs based on the R-EGP-CQDs-NMe2, -NEt2, and -NPr2 display voltage-stable warm white spectra with a maximum luminance of 5248-5909 cd m-2 and a current efficiency of 3.65-3.85 cd A-1. The warm-WLEDs also show good long-term operational stability (L/L 0 > 80% after 50 h operation, L 0: 1000 cd m-2). The electron-donating group passivation strategy opens a new avenue to realizing efficient red bandgap emission CQDs and developing high-performance electroluminescent warm-WLEDs.

Polyetherimide Foams Filled with Low Content of Graphene Nanoplatelets Prepared by scCO₂ Dissolution

Polyetherimide (PEI) foams with graphene nanoplatelets (GnP) were prepared by supercritical carbon dioxide (scCO₂) dissolution. Foam precursors were prepared by melt-mixing PEI with variable amounts of ultrasonicated GnP (0.1⁻2.0 wt %) and foamed by one-step scCO₂ foaming. While the addition of GnP did not significantly modify the cellular structure of the foams, melt-mixing and foaming induced a better dispersion of GnP throughout the foams. There were minor changes in the degradation behaviour of the foams with adding GnP. Although the residue resulting from burning increased with augmenting the amount of GnP, foams showed a slight acceleration in their primary stages of degradation with increasing GnP content. A clear increasing trend was observed for the normalized storage modulus of the foams with incrementing density. The electrical conductivity of the foams significantly improved by approximately six orders of magnitude with only adding 1.5 wt % of GnP, related to an improved dispersion of GnP through a combination of ultrasonication, melt-mixing and one-step foaming, leading to the formation of a more effective GnP conductive network. As a result of their final combined properties, PEI-GnP foams could find use in applications such as electrostatic discharge (ESD) or electromagnetic interference (EMI) shielding.

Reduced Graphene Oxide-Immobilized Tris(bipyridine)ruthenium(II) Complex for Efficient Visible-Light-Driven Reductive Dehalogenation Reaction

A sodium benzenesulfonate (PhSO3Na)-functionalized reduced graphene oxide was synthesized via a two-step aryl diazonium coupling and subsequent NaCl ion-exchange procedure, which was used as a support to immobilize tris(bipyridine)ruthenium(II) complex (Ru(bpy)3Cl2) by coordination reaction. This elaborated Ru(bpy)3-rGO catalyst exhibited excellent catalytic efficiency in visible-light-driven reductive dehalogenation reactions under mild conditions, even for ary chloride. Meanwhile, it showed the comparable reactivity with the corresponding homogeneous Ru(bpy)3Cl2 catalyst. This high catalytic performance could be attributed to the unique two-dimensional sheet-like structure of Ru(bpy)3-rGO, which efficiently diminished diffusion resistance of the reactants. Meanwhile, the nonconjugated PhSO3Na-linkage between Ru(II) complex and the support and the very low electrical conductivity of the catalyst inhibited energy/electron transfer from Ru(II) complex to rGO support, resulting in the decreased support-induced quenching effect. Furthermore, it could be easily recycled at least five times without significant loss of catalytic reactivity.

Hybrid Amine-Functionalized Graphene Oxide as a Robust Bifunctional Catalyst for Atmospheric Pressure Fixation of Carbon Dioxide using Cyclic Carbonates

An environmentally-benign carbocatalyst based on amine-functionalized graphene oxide (AP-GO) was synthesized and characterized. This catalyst shows superior activity for the chemical fixation of CO2 into cyclic carbonates at the atmospheric pressure. The developed carbocatalyst exhibits superior activity owing to its large surface area with abundant hydrogen bonding donor (HBD) capability and the presence of well-defined amine functional groups. The presence of various HBD and amine functional groups on the graphene oxide (GO) surface yields a synergistic effect for the activation of starting materials. Additionally, this catalyst shows high catalytic activity to synthesize carbonates at 70 °C and at 1 MPa CO2 pressure. The developed AP-GO could be easily recovered and used repetitively in up to seven recycle runs with unchanged catalyst activity.

Synthesis and characterization of 1,3-diamino-graphene as a heterogeneous ligand for a CuI-catalyzed C–N coupling reaction

1,3-Diamino-graphene was synthesized and used as an efficient heterogeneous ligand for a CuI-catalyzed C–N coupling reaction.

Liquid crystal polaroid glass electrode from e-waste for synchronized removal/recovery of Cr(+6) from wastewater by microbial fuel cell

This study demonstrates the use of Liquid Crystal coated Polaroid Glass Electrode (LCPGE) material collected from disposed liquid-crystal display (LCD) computer monitor as electrodes in microbial fuel cell (MFC) for the simultaneous reduction/recovery of Cr(+6) from chromium wastewater. Fourier transform infrared spectrum (FT-IR) confirms the presence of NH2, CN, CO and OC and/or COC functional groups in LCPGE. An excellent electrochemical performance with distinct redox peaks were observed in cyclic voltammetry test (100 mV/s). The maximum current density of 110 mA/m(2) (10 mW/m(2)) was achieved by operating MFC in batch mode. At the cathode LCPGE (10.5 cm(2)) interface, toxic Cr(+6) ions readily accepted electrons and formed nontoxic Cr2O3 as confirmed by FT-IR and X-ray photoelectron spectroscopy analysis. Moreover, electrochemical impedance analysis shows that bacteria were readily attached to the surface of LCPGE (10.5 cm(2)) within 24 h in a Bioelectrochemical System (BES).

Self-assembled graphene oxide microcapsules with adjustable permeability and yolk-shell superstructures derived from atomized droplets

GO microcapsules were assembled on the surface of atomized droplets prepared by a spray-drying strategy. The nanochannels in the microcapsule wall can be adjusted by water-soluble polymers and make the microcapsule exhibit sustained release. The strategy can further be employed to encapsulate metal organic frameworks to obtain MOF-GO yolk-shell superstructures.

Organoamine-functionalized graphene oxide as a bifunctional carbocatalyst with remarkable acceleration in a one-pot multistep reaction

In this work, we reported the synthesis of bifunctional carbocatalyst with acid-base dual-activation mechanism by introducing organoamines on the basal planes of graphene oxide (GO). Interestingly, GO-supported primary amine (AP-GO) exclusively promoted one-pot Henry-Michael reactions with excellent activity to give synthetically valuable multifunctionalized nitroalkanes. Notably, it also exhibited significantly higher activity than those using propylamine, activated carbon-supported primary amine, and mesoporous silica-supported primary amine as the catalysts. This superior catalytic performance originated from the unique properties of AP-GO, which provided the acid-base cooperative effect by the appropriate positioning of primary amines on their basal planes and carboxyl acids along their edges and the decreased diffusion resistance of the reactants and the intermediates during the multistep catalytic cycles because of its open two-dimensional sheet-like structure. Moreover, it could be readily recycled by simple filtration and subsequently reused without significant loss of its catalytic activity in a six times run test.

Biomaterial functionalized graphene oxides with tunable work function for high sensitive organic photodetectors

Amino acid functionalized graphene acts as an ideal material for transparent conductive electrodes in optoelectronic devices attributed to its tunable work function, excellent electrical conductivity and optical transparency.

Multiple roles of graphene in heterogeneous catalysis

This review provides a brief but comprehensive understanding of the different roles of graphene in heterogeneous catalysis, i.e., its use as a catalyst support and its intrinsic catalytic properties originating from the defects and heteroatom-containing functionalities.