An In situ TEM study of the surface oxidation of palladium nanocrystals assisted by electron irradiation

Highly Durable Chemoresistive Micropatterned PdAu Hydrogen Sensors: Performance and Mechanism

Hydrogen (H2) is a promising alternative energy source for Net-zero, but the risk of explosion requires accurate and rapid detection systems. As the use of H2 energy expands, sensors require high performance in a variety of properties. Palladium (Pd) is an attractive material for H2 detection due to its high H2 affinity and catalytic properties. However, poor stability caused by volume changes and reliability due to environmental sensitivity remain obstacles. This study proposes a micropatterned thin film of PdAu with optimized composition (Pd0.62Au0.38) as a chemoresistive sensor to overcome these issues. At room temperature, the sensor has a wide detection range of 0.0002% to 5% and a fast response time of 9.5 s. Significantly, the sensor exhibits excellent durability for repeated operation (>35 h) in 5% H2 and resistance to humidity and carbon monoxide. We also report a negative resistivity change in PdAu, which is opposite to that of Pd. Density functional theory (DFT) calculations were performed to investigate the resistance change. DFT analysis revealed that H2 penetrates specific interstitial sites, causing partial lattice compression. The lattice compression causes a decrease in electrical resistance. This work is expected to contribute to the development of high-performance H2 sensors using Pd-based alloys.

Hydrazone-Linked Covalent Organic Framework Catalyst via Efficient Pd Recovery from Wastewater

Global consumption and discharge of palladium (Pd) have raised environmental concerns but also present an opportunity for the sustainable recovery and reuse of this precious metal. Adsorption has proven to be an efficient method for the selective recovery of Pd from industrial wastewater. This study investigated a hydrazone-linked covalent organic framework (Tfpa-Od COF) as a potential material for the high-affinity adsorption of Pd2+ ions from wastewater, achieving a Kd value of 3.62 × 106 mL g-1. The electron-rich backbone of the COF contributes to its excellent selective removal efficiency (up to 100%) and adsorption capacity of 372.59 mg g-1. Furthermore, the Pd-adsorbed COF was evaluated as a sustainable catalyst for the Suzuki-Miyaura coupling reaction, demonstrating good catalytic conversion and recyclability. This work attempts to showcase a protocol for reusing waste palladium generated in water to fabricate heterogeneous catalysts and, thereby, promote the circular economy concept.

Exploring Catalytic Intermediates in Pd-Catalyzed Aerobic Oxidative Amination of 1,3-Dienes: Multiple Metal Interactions of the Palladium Nanoclusters

Metal nanoclusters (NCs) have unique properties because of their small size, which makes them useful as catalysts in reactions like cross-coupling. Pd-catalyzed oxidative amination, which involves dehydrogenative C-N bond formation, uses Pd complexes as the active species. It is known that the catalytic conditions involve the formation of Pd(0) species from Pd NCs, but the precise role of Pd NCs in the transformations has not been established. In this study, we investigated the characteristic properties of Pd NCs in oxidative amination of 1,3-dienes. The reaction achieved direct amination of commercially accessible 1,3-dienes with secondary aromatic amines, providing a variety of nitrogen containing 1,3-dienes. The compound was applicable to radical polymerization to provide the nitrogen-fabricated 1,3-diene-based polymer, which exhibited a different thermal stability compared to aliphatic nitrogen-fabricated diene polymers. In addition to the synthetic utility, by combining X-ray absorption fine structure and small-angle X-ray scattering analysis, we revealed amines and 1,3-dienes affected metal leaching from the Pd nanoparticles and stabilization of Pd NCs in the catalytic reaction. Additionally, DFT calculation suggested that the catalytic intermediate contained multiple adjacent Pd atoms and was responsible for formation of an σ-allylic intermediate that is difficult to form with the use of Pd complexes. These results could be used to understand the underlying phenomenon in the oxidative coupling reaction and develop Pd NCs-based dehydrogenation.

Substantially Accelerated Response and Recovery in Pd-Decorated WO3 Nanorods Gasochromic Hydrogen Sensor

The development of hydrogen (H2) gas sensors is essential for the safe and efficient adoption of H2 gas as a clean, renewable energy source in the challenges against climate change, given its flammability and associated safety risks. Among various H2 sensors, gasochromic sensors have attracted great interest due to their highly intuitive and low power operation, but slow kinetics, especially slow recovery rate limited its further practical application. This study introduces Pd-decorated amorphous WO3 nanorods (Pd-WO3 NRs) as an innovative gasochromic H2 sensor, demonstrating rapid and highly reversible color changes for H2 detection. In specific, the amorphous nanostructure exhibits notable porosity, enabling rapid detection and recovery by facilitating effective H2 gas interaction and efficient diffusion of hydrogen ions (H+) dissociated from the Pd nanoparticles (Pd NPs). The optimized Pd-WO3 NRs sensor achieves an impressive response time of 14 s and a recovery time of 1 s to 5% H2. The impressively fast recovery time of 1 s is observed under a wide range of H2 concentrations (0.2-5%), making this study a fundamental solution to the challenged slow recovery of gasochromic H2 sensors.

Redox dynamics and surface structures of an active palladium catalyst during methane oxidation

Catalysts based on palladium are among the most effective in the complete oxidation of methane. Despite extensive studies and notable advances, the nature of their catalytically active species and conceivable structural dynamics remains only partially understood. Here, we combine operando transmission electron microscopy (TEM) with near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) and density functional theory (DFT) calculations to investigate the active state and catalytic function of Pd nanoparticles (NPs) under methane oxidation conditions. We show that the particle size, phase composition and dynamics respond appreciably to changes in the gas-phase chemical potential. In combination with mass spectrometry (MS) conducted simultaneously with in situ observations, we uncover that the catalytically active state exhibits phase coexistence and oscillatory phase transitions between Pd and PdO. Aided by DFT calculations, we provide a rationale for the observed redox dynamics and demonstrate that the emergence of catalytic activity is related to the dynamic interplay between coexisting phases, with the resulting strained PdO having more favorable energetics for methane oxidation.

Flow cytometry-based high-throughput screening of synthetic peptides for palladium adsorption

Conventionally, the measurement of metal ion adsorption capacity in biosorbent relies on expensive and time-consuming ICP-OES technique. Herein, a semi-quantitative method to measure Pd(II) adsorption capacity of single cells has been presented by analyzing side scatter (SSC) intensity in flow cytometry. Within the sensitive range and applicable conditions, excellent linearity correlation (R2 ranges from 0.89 to 0.96) between the amount of Pd(II) absorbed on yeast and the fold increase in SSC intensity has been observed. Using this method, six strains with high Pd adsorption capacities have sorted from a yeast library with metal-binding peptides displayed (up to 107 strains) based on SSC signal intensity. The optimal peptide (EF1) displayed on yeast and E. coli surface demonstrated Pd adsorption improvements of ∼32% and ∼200%, respectively. In summary, our study proposes an alternative high-throughput method for analyzing the Pd(II) adsorption capacity of individual yeast cells, enabling the screening of specific peptides/proteins with high Pd(II) affinity from extensive libraries.

Influence of the drying mode of support on the properties of Pd/Al2O3-ZrO2 materials used for methane combustion

This work constitutes a new trial to enhance the properties of palladium supported on alumina modified with zirconium used as catalysts for methane combustion. The effect of the support drying mode is studied. For this aim, Al2O3-ZrO2 binary oxides with zirconium loading of 2 and 5% in weight were prepared using sol-gel process then dried under ordinary or supercritical conditions. Palladium with a loading of 0.5% was deposited on the support by wet impregnation. Several techniques have been used to investigate differences between the two types of the derived catalysts.

Secondary Amines from Catalytic Amination of Bio-Derived Phenolics over Pd/C and Rh/C: Effect of Operation Parameters

The production of renewable chemicals using lignocellulosic biomass has gained significant attention in green chemistry. Among biomass-derived chemicals, secondary amines have emerged as promising intermediates for synthetic applications. Here, we report a systematic study on the reductive amination of phenolics with cyclohexylamine using Pd/C and Rh/C as catalysts. The catalytic tests were performed in batch reactors under different reaction conditions (various: amine concentration (0.1–0.4 mol/L), hydrogen pressure (0–2.5 bar), temperature (80–160 °C), and substituted phenols (phenol, o-cresol, p-cresol, and methoxyphenol)) and using tert-amyl alcohol as a solvent. The experimental observations were consistent with a multi-step mechanism, where hydrogenation of phenol to cyclohexanone is followed by condensation of the ketone with cyclohexylamine to form an imine, which is finally hydrogenated to produce secondary amines. In addition, there was evidence of parallel self-condensation of the cyclohexylamine. The study also supported a limited dehydrogenation capacity of Rh/C, unlike Pd/C, which increases this capacity at higher temperatures generating a higher yield of cyclohexylaniline (up to 15%). The study of the alkylated phenols demonstrated that the nature and propensity of hydrogenation of the phenolic controls their amination. Kinetic analysis revealed reaction orders between 0.4 and 0.7 for H2, indicating its dissociative adsorption. Meanwhile, phenol’s order (between 1–1.8) suggests a single participation of this compound in the hydrogenation step. The order of 0.4 for cyclohexylamine suggests its participation as a surface-abundant species. The apparent activation energies derived from a power law approximation were of 37 kJ/mol and 10 kJ/mol on Pd/C and Rh/C, respectively.

Synthesizing ordered mesoporous Ni spheres with uniform and adjustable size through a one-step Pd2+-assisted soft-templating strategy

Developing an effective way to synthesize uniform ordered mesoporous metal spheres with controllable diameter is important for enhancing their performance in various applications but remains a challenge. Herein, a one-step and facile Pd²⁺-assisted soft-templating strategy is reported to synthesize ordered mesoporous Ni spheres (OMNiS) with highly uniform and tunable diameters. In this synthesis methodology, lyotropic liquid crystals (LLCs) are used as a meso-structural template and Pd nuclei obtained from the reduction of Pd²⁺ ions are used as nucleation sites for directing Ni deposition. The OMNiS samples with average sphere diameter ranging from 50 nm to 190 nm are produced by varying the amount of Pd²⁺ in the LLC precursor, revealing that the Pd nuclei play a key role in improving the uniformity of the mesoporous Ni spheres and adjusting the sphere diameter. The satisfactory combination of uniform sphere size, high surface area, great conductivity, and highly ordered mesoporous structure for the optimal OMNiS-100 sample contributes to its superior electrocatalytic activity for the oxygen evolution reaction (OER) in an alkaline electrolyte with a low overpotential of 271 mV to drive a current density of 10 mA cm^-2, which is much smaller than that of RuO₂ (368 mV), along with a remarkable durability.

Revealing Surface Restraint-Induced Hexagonal Pd Nanocrystals via In Situ Transmission Electron Microscopy

Achieving metal nanocrystals with metastable phase draws much attention due to their anticipated fascinating properties, wheras it is still challenging because their polymorphism nature and phase transition mechanism remain elusive. Here, phase stability of face-centered cubic (fcc) Pd nanocrystals was studied via in situ spherical aberration (Cs)-corrected transmission electron microscopy (TEM). By constructing a well-defined Pd/C composite structure, Pd nanocrystals encapsulated by graphite, the dispersion process of fcc Pd was observed through a nucleation and growth process. Interestingly, Cs-corrected scanning TEM analysis demonstrated that the newly formed Pd nanocrystals could adopt a metastable hexagonal phase, which was considered challenging to obtain. Accordingly, formation mechanism of the hexagonal Pd nanocrystals was proposed, which involved the combined effect of two factors: (1) templating of graphite and (2) size effect. This work is expected to offer new insight into the polymorphism of Pd nanocrystals and pave the way for the future design of metastable metal nanomaterials.

Sonogashira Synthesis of New Porous Aromatic Framework-Entrapped Palladium Nanoparticles as Heterogeneous Catalysts for Suzuki-Miyaura Cross-Coupling

Palladium nanoparticles entrapped in porous aromatic frameworks (PAFs) or covalent organic frameworks may promote heterogeneous catalytic reactions. However, preparing such materials as active nanocatalysts usually requires additional steps for palladium entrapment and reduction. This paper reports as a new approach, a simple procedure leading to the self-entrapment of Pd nanoparticles within the PAF structure. Thus, the selected Sonogashira synthesis affords PAF-entrapped Pd nanoparticles that can catalyze the C-C Suzuki-Miyaura cross-coupling reactions. Following this new concept, PAFs were synthesized via Sonogashira cross-coupling of the tetraiodurated derivative of tetraphenyladamantane or spiro-9,9'-bifluorene with 1,6-diethynylpyrene, then characterized them using powder X-ray diffraction, diffuse reflectance infrared Fourier transform spectroscopy, X-ray photoelectron spectroscopy, high-resolution scanning transmission electron microscopy, and textural properties (i.e., adsorption-desorption isotherms). The PAF-entrapped Pd nanocatalysts showed high catalytic activity in Suzuki-Miyaura coupling reactions (demonstrated by preserving the turnover frequency values) and stability (demonstrated by palladium leaching and recycling experiments). This new approach presents a new class of PAFs with unique structural, topological, and compositional complexities as entrapped metal nanocatalysts or for other diverse applications.

Reductive amination of phenol over Pd-based catalysts: elucidating the role of the support and metal nanoparticle size

The Pd-catalyzed reductive amination of phenol is sensitive to the support's nature, and to the atoms' coordination in palladium clusters.

Insight into ultrasensitive and high-stability flocculation-enhanced Raman spectroscopy for the in situ noninvasive probing of cupping effect substances

The combination of in situ TEM and theoretical analysis is applied to further analyze the behavior of nanoparticles in flocculation; particularly, for the in situ noninvasive probing of effect substances after cupping.

Optimization of the In Situ Biasing FIB Sample Preparation for Hafnia-Based Ferroelectric Capacitor

Hafnia-based ferroelectric (FE) thin films have received extensive attention in both academia and industry, benefitting from their outstanding scalability and excellent CMOS compatibility. Hafnia-based FE capacitors in particular have the potential to be used in dynamic random-access memory (DRAM) applications. Obtaining fine structure characterization at ultra-high spatial resolution is helpful for device performance optimization. Hence, sample preparation by the focused ion beam (FIB) system is an essential step, especially for in situ biasing experiments in a transmission electron microscope (TEM). In this work, we put forward three tips to improve the success rate of in situ biasing experiments: depositing a carbon protective layer to position the interface, welding the sample on the top of the Cu column of the TEM grid, and cutting the sample into a comb-like shape. By these means, in situ biasing of the FE capacitor was realized in TEM, and electric-field-induced tetragonal (t-) to monoclinic (m-) structure transitions in Hf_0.5Zr_0.5O₂ FE film were observed. The improvement of FIB sample preparation technology can greatly enhance the quality of in situ biasing TEM samples, improve the success rate, and extend from capacitor sample preparation to other types.

Steam-created grain boundaries for methane C-H activation in palladium catalysts

[Figure: see text].

An Investigation of Active Sites for electrochemical CO2 Reduction Reactions: From In Situ Characterization to Rational Design

The electrochemical carbon dioxide (CO2) reduction reaction (CO2RR) is among the most promising approaches used to transform greenhouse gas into useful fuels and chemicals. However, the reaction suffers from low selectivity, high overpotential, and low reaction rate. Active site identification in the CO2RR is vital for the understanding of the reaction mechanism and the rational development of new electrocatalysts with both high selectivity and stability. Herein, in situ characterization monitoring of active sites during the reaction is summarized and a general understanding of active sites on the various catalysts in the CO2RR, including metal-based catalysts, carbon-based catalysts, and metal-organic frameworks-based electrocatalysts is updated. For each type of electrocatalysts, the reaction pathway and real active sites are proposed based on in situ characterization techniques and theoretical calculations. Finally, the key limitations and challenges observed for the electrochemical fixation of CO2 is presented. It is expected that this review will provide new insights and directions into further scientific development and practical applicability of CO2 electroreduction.

'Pre-optimization' of the solvent of nanoparticle synthesis for superior catalytic efficiency: a case study with Pd nanocrystals

In view of a limited rationale available for designing metal nanocrystals (NCs) to achieve high catalytic activities across various chemical transformations, we offer a new perspective on the optimization of the 'solvent-of-nanocrystal-synthesis' that, to an extent, would help bypass the tedious characterization needs. A systematic improvement in a catalyst is hindered because (i) it relies on size & shape control protocols, surface characterization, understanding molecular transformation mechanisms, and the energetics of the reactant-catalyst interactions, requiring the involvement of different domains experts, and (ii) the insights developed using model reactions may not easily extend to other reactions, although the current studies count on such a hypothesis. In support of (ii), by taking Pd NCs as catalysts and two distinct reaction types, viz. Suzuki coupling and nitroarene reduction, we show to what great extent the reaction rates may vary even for the seemingly similar reactions by using the same NCs. More importantly, for challenge (i), we demonstrate how the addition of a single-step to the current protocol of 'catalyst-synthesis and activity test' can potentially lead to the development of highly active catalysts by first finding a suitable solvent for the NC synthesis, while such solvent-effects are barely considered unlike the same in organic transformation reactions as a matter of routine, for example.

Pd Nanocluster/Monolayer MoS2 Heterojunctions for Light-Induced Room-Temperature Hydrogen Sensing

Developing sensing approaches that can exploit visible light for the detection of low-concentration hydrogen at room temperatures has become increasingly important for the safe use of hydrogen in many applications. In this study, heterostructures composed of monolayer MoS₂ and Pd nanoclusters (Pd/MoS₂) acting as photo- and hydrogen-sensitizers are successfully fabricated in a facile and scalable manner. The uniform deposition of morphologically isotropic Pd nanoclusters (11.5 ± 2.2 nm) on monolayer MoS₂ produces a plethora of active heterojunctions, effectively suppressing charge carrier recombination under light illumination. The dual photo- and hydrogen-sensitizing functionality of Pd/MoS₂ can enable its use as an active sensing layer in optoelectronic hydrogen sensors. Gas-sensing examinations reveal that the sensing performance of Pd/MoS₂ is enhanced three-fold under visible light illumination (17% for 140 ppm of H₂) in comparison with dark light (5% for 140 ppm of H₂). Photoactivation is also found to enable excellent sensing reversibility and reproducibility in the obtained sensor. As a proof-of-concept, the integration of Pd nanoclusters and monolayer MoS₂ can open a new avenue for light-induced hydrogen gas sensing at room temperature.

Chemical Evolution of Pt-Zn Nanoalloys Dressed in Oleylamine

We report on the shape, composition (from Pt₉₅Zn₅ to Pt₇₇Zn₂₃), and surface chemistry of Pt-Zn nanoparticles obtained by reduction of precursors M²⁺(acac)₂^- (M²⁺: Pt²⁺ and Zn²⁺) in oleylamine, which serves as both solvent and ligand. We show first that the addition of phenyl ether or benzyl ether determines the composition and shape of the nanoparticles, which point to an adsorbate-controlled synthesis. The organic (ligand)/inorganic (nanoparticles) interface is characterized on the structural and chemical level. We observe that the particles, after washing with ethanol, are coated with oleylamine and the oxidation products of the latter, namely, an aldimine and a nitrile. After exposure to air, the particles oxidize, covering themselves with a few monolayer thick ZnO film, which is certainly discontinuous when the particles are low in zinc. Pt-Zn particles are unstable and prone to losing Zn. We have strong indications that the driving force is the preferential oxidation of the less noble metal. Finally, we show that adsorption of CO on the surface of nanoparticles modifies the oxidation state of amine ligands and attribute it to the displacement of hydrogen adsorbed on Pt. All the structural and chemical information provided by the combination of electron microscopy and X-ray photoelectron spectroscopy allows us to give a fairly accurate picture of the surface of nanoparticles and to better understand why Pt-Zn alloys are efficient in certain electrocatalytic reactions such as the oxidation of methanol.

Volcano-type correlation between particle size and catalytic activity on hydrodechlorination catalyzed by AuPd nanoalloy

Although changing the size of metal nanoparticles (NPs) is a reasonable way to tune and/or enhance their catalytic activity, size-selective preparation of NPs possessing random-alloy morphology has been challenging because of the differences in the ionization potential of each metal ion. This study demonstrates a time-controlled aggregation-stabilization method for the size-selective preparation of random alloy NPs composed of Au and Pd, which are stabilized by poly(N-vinyl-2-pyrrolidone) (PVP). By adjusting the mixing time in the presence of a small amount of PVP, aggregation was induced to produce AuPd:PVP with sizes ranging between 1.2 and 8.2 nm at approximately 1 nm intervals. Transmission electron microscopy (TEM), powder X-ray diffraction (PXRD), and extended X-ray absorption fine structure (EXAFS) analyses indicated the formation of various sizes of AuPd nanoalloys, and size-dependent catalytic activity was observed when hydrodechlorination of 4-chloroanisole was performed using 2-propanol as a reducing agent. AuPd:PVP with a size of 3.1 nm exhibited the highest catalytic activity. A comparison of the absorption edges of X-ray absorption near edge structure (XANES) spectra suggested that the electronic state of the Au and Pd species correlated with their catalytic activity, presumably affecting the rate-determining step.

In situ investigation of oxidation across a heterogeneous nanoparticle-support interface during metal support interactions

Interactions between oxide supports and noble metal nanoparticles (NPs) is an area of intense research interest across all fields of catalysis. Oxygen spillover, metal support interactions (MSIs) and charge transfer are among many mechanisms observed and proposed as to how NP-support interfaces assist and enhance catalysis. This work studies the migration of oxygen across the Pd NP-CuO nanowire (NW) interface and beyond. X-ray photoelectron spectroscopy (XPS) and Kelvin probe force microscopy (KPFM) found an interaction between the Pd NP and CuO NW support, via the formation of PdO at the Pd-CuO interface. It was found, through in situ irradiation at high vacuum transmission electron microscopy (TEM), that oxygen enters the Pd NP lattice from the Pd-CuO interface via amorphization of the NP. Varying the amount of irradiation highlighted the different rates of amorphization of NPs, with full amorphization of a NP leading to the formation of an epitaxially driven PdO across the NPs. Interestingly, in situ heating in XPS observed a reduction to metallic Pd, found to be similarly amorphous during TEM investigation. On comparison with Pd supported on a non-reducible substrate - in which oxidation was found to proceed from the outer surface in, rather than the support interface (resulting in a PdO shell) - it is theorized that the oxidation and reduction of Pd on CuO forms a PdO NP surface full of Pd-PdO sites allowing for synergistic effects, of great use in the oxidation and hydrogenation of organic species.

A novel Co-based MOF/Pd composite: synergy of charge-transfer towards the electrocatalytic oxygen evolution reaction

A novel Co-based MOF/Pd composite (LEEL-037/Pd-C) presented an electronic transference (Co 3d orbital → linkers π* → Pd 5S orbital) promoting an enhanced OH⁻ adsorption, thus improving the oxygen evolution reaction (OER) in alkaline medium.

In Situ Oxidation Studies of High-Entropy Alloy Nanoparticles

Although high-entropy alloys (HEAs) have shown tremendous potential for elevated temperature, anticorrosion, and catalysis applications, little is known on how HEA materials behave under complex service environments. Herein, we studied the high-temperature oxidation behavior of Fe_0.28Co_0.21Ni_0.20Cu_0.08Pt_0.23HEA nanoparticles (NPs) in an atmospheric pressure dry air environment by in situ gas-cell transmission electron microscopy. It is found that the oxidation of HEA NPs is governed by Kirkendall effects with logarithmic oxidation rates rather than parabolic as predicted by Wagner's theory. Further, the HEA NPs are found to oxidize at a significantly slower rate compared to monometallic NPs. The outward diffusion of transition metals and formation of disordered oxide layer are observed in real time and confirmed through analytical energy dispersive spectroscopy, and electron energy loss spectroscopy characterizations. Localized ordered lattices are identified in the oxide, suggesting the formation of Fe₂O₃, CoO, NiO, and CuO crystallites in an overall disordered matrix. Hybrid Monte Carlo and molecular dynamics simulations based on first-principles energies and forces support these findings and show that the oxidation drives surface segregation of Fe, Co, Ni, and Cu, while Pt stays in the core region. The present work offers key insights into how HEA NPs behave under high-temperature oxidizing environment and sheds light on future design of highly stable alloys under complex service conditions.

In Situ Tracking of Colloidally Stable and Ordered Assemblies of Gold Nanorods

Solution-phase self-assembly of anisotropic nanoparticles into complex 2D and 3D assemblies is one of the most promising strategies toward obtaining nanoparticle-based materials and devices with unique optical properties at the macroscale. However, controlling this process with single-particle precision is highly demanding, mostly due to insufficient understanding of the self-assembly process at the nanoscale. We report the use of in situ environmental scanning transmission electron microscopy (WetSTEM), combined with UV/vis spectroscopy, small-angle X-ray diffraction (SAXRD) and multiscale modeling, to draw a detailed picture of the dynamics of vertically aligned assemblies of gold nanorods. Detailed understanding of the self-assembly/disassembly mechanisms is obtained from real-time observations, which provide direct evidence of the colloidal stability of side-to-side nanorod clusters. Structural details and the forces governing the disassembly process are revealed with single particle resolution as well as in bulk samples, by combined experimental and theoretical modeling. In particular, this study provides unique information on the evolution of the orientational order of nanorods within side-to-side 2D assemblies and shows that both electrostatic (at the nanoscale) and thermal (in bulk) stimuli can be used to drive the process. These results not only give insight into the interactions between nanorods and the stability of their assemblies, thereby assisting the design of ordered, anisotropic nanomaterials but also broaden the available toolbox for in situ tracking of nanoparticle behavior at the single-particle level.

In Situ Formation of Free-Standing Single-Atom-Thick Antiferromagnetic Chromium Membranes

Compared to van der Waals two-dimensional (2D) layers with lateral covalent bonds, metallic bonding systems favor close-packed structures, and thus, free-standing 2D metals have remained, for the most part, elusive. However, a number of theoretical studies suggest a number of metals can exist as 2D materials and a few early experiments support this notion. Here we demonstrate free-standing single-atom-thick crystalline chromium (Cr) suspended membranes using aberration-corrected transmission electron microscopy and image simulations. Density functional theory studies confirm the 2D Cr membranes have an antiferromagnetic ground state making them highly attractive for spintronic applications. Moreover, the work also helps consolidate the existence of a new family of 2D metal layers.

Amino-Modified Silica as Effective Support of the Palladium Catalyst for 4-Nitroaniline Hydrogenation

The article describes the synthesis of aminoorgano-functionalized silica as a prospective material for catalysis application. The amino groups have electron donor properties which are valuable for the metal chemical state of palladium. Therefore, the presence of electron donor groups is important for increasing catalysts’ stability. The research is devoted to the investigation of silica amino-modified support influence on the activity and stability of palladium species in 4-nitroaniline hydrogenation process. A series of catalysts with different supports such as SiO2, SiO2-C3H6-NH2 (amino-functionalized silica), γ-Al2O3 and activated carbon were studied. The catalytic activity was studied in the hydrogenation of 4-nitroaniline to 1,4-phenylenediamine. The catalysts were characterized by scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and chemisorption of hydrogen by the pulse technique. The 5 wt.% Pd/SiO2-C3H6-NH2 catalyst exhibited the highest catalytic activity for 4-nitroaniline hydrogenation with 100% conversion and 99% selectivity with respect to 1,4-phenylenediamine.

In situ one-step synthesis of polymer-functionalized palladium nanoparticles: an efficient anticancer agent against breast cancer

Breast cancer is the most common malignancy among women worldwide, and researchers are working to discover effective treatments to eradicate breast cancer. In the present study, we prepared PVP-functionalized palladium nanoparticles (PVP-PdNPs) for the treatment of human breast cancer MCF7 cells. Initially, the PVP-functionalized PdNPs were synthesized by an in situ method and confirmed with DRS-UV spectrometric analysis. Further, FTIR and Raman spectroscopic analyses showed the association of PVP with PdNPs by showing the vibrational mode of the PdNPs and C[double bond, length as m-dash]O stretch and CH₂ band modes of PVP. Microscopic analysis showed that the PVP-PdNPs have a narrow size distribution with spherical shapes and a size range between 9 and 15 nm. The SAED and XRD patterns confirmed that the crystalline structure is face-centered cubic in nature, and EDAX mapping confirmed the formulation of PVP on the surface of the PdNPs. Further, in vitro MTT assay analysis showed that the PVP-PdNPs exhibit excellent cytotoxic activity against human breast cancer MCF7 cells in a dose-dependent manner. The PVP-PdNPs generate continuous ROS in the mitochondria; this leads to the damage of the mitochondrial membrane potential and nuclear DNA and induces apoptosis through caspase3/7 enzymatic activity. Together, the PVP-PdNPs are a promising potential anticancer agent against human breast cancer.

Core-shell PdCu bimetallic colloidal nanoparticles in Sonogashira cross-coupling reaction: mechanistic insights into the catalyst mode of action

Core-shell PdCu nanoparticles with different metal proportions were synthesized using a one-pot methodology and characterized by STEM, HRTEM, XANES and EXAFS analysis. The bimetallic nanoparticles were applied as catalysts in the Sonogashira cross-coupling reaction to investigate the mode of action of the PdCu in the reaction. The copper content directly influenced the generation of the cross-coupling product, shaping the performance of the catalyst. A quasi-homogeneous reaction pathway was evidenced by kinetics and poisoning experiments as well as XAS, HRTEM and HRMS analysis. These findings help to elucidate the mode of action of the PdCu nanocatalysts in the, as yet, unrevealed Sonogashira mechanism and the potential development of new nanocatalysts.

Synthesis, growth mechanisms, and applications of palladium-based nanowires and other one-dimensional nanostructures

Palladium-based nanostructures have attracted the attention of researchers due to their useful catalytic properties and unique ability to form hydrides, which finds application in hydrogen storage and hydrogen detection. Palladium-based nanowires have some inherent advantages over other Pd nanomaterials, combining high surface-to-volume ratio with good thermal and electron transport properties, and exposing high-index crystal facets that can have enhanced catalytic activity. Over the past two decades, both synthesis methods and applications of 1D palladium nanostructures have advanced greatly. In this review, we start by discussing different types of 1D palladium nanostructures before moving on to the different synthesis approaches that can produce them. Next, we discuss factors including kinetic vs. thermodynamic control of growth, oxidative etching, and surface passivation that affect palladium nanowire synthesis. We also review efforts to gain insight into growth mechanisms using different characterization tools. We discuss the effects of concentration of capping agents, reducing agents, metal halides, pH, and sacrificial oxidation on the growth of Pd-based nanowires in solution, from shape control, to yield, to aspect ratio. Various applications of palladium and palladium alloy nanowires are then discussed, including electrocatalysis, hydrogen storage, and sensing of hydrogen and other chemicals. We conclude with a summary and some perspectives on future research directions for this category of nanomaterials.

Cancer-derived exosomes loaded with ultrathin palladium nanosheets for targeted bioorthogonal catalysis

The transformational impact of bioorthogonal chemistries has inspired new strategies for the in vivo synthesis of bioactive agents through non-natural means. Among these, palladium (Pd) catalysts have played a prominent role in the growing subfield of bioorthogonal catalysis by producing xenobiotics and uncaging biomolecules in living systems. However, delivering catalysts selectively to specific cell types still lags behind catalyst development. Here we have developed a bio-artificial device consisting of cancer-derived exosomes loaded with Pd catalysts by a method that enables the controlled assembly of Pd nanosheets directly inside the vesicles. This hybrid system mediates Pd-triggered dealkylation reactions in vitro and inside cells and displays preferential tropism for their progenitor cells. The use of Trojan exosomes to deliver abiotic catalysts into designated cancer cells creates the opportunity for a new targeted therapy modality: exosome-directed catalyst prodrug therapy, whose first steps are presented herein with the cell-specific release of the anticancer drug panobinostat.

Gas Sensor by Direct Growth and Functionalization of Metal Oxide/Metal Sulfide Core-Shell Nanowires on Flexible Substrates

We have developed a novel fabrication method for flexible gas sensors for toxic gases based on sequential wet chemical reaction. In specific, zinc oxide (ZnO) nanowires were locally synthesized and directly integrated on a flexible polymer substrate using localized hydrothermal synthesis methods and their surfaces were selectively functionalized with palladium (Pd) nanoparticles using a liquid phase deposition process. Because the entire process is conducted at a low temperature in a mild precursor solution, it can be applied for flexible substrates. Furthermore, the surface of ZnO nanowires was sulfurized by hydrogen sulfide (H₂S) gas to form zinc oxide/zinc sulfide (ZnO/ZnS) core-shell nanowires for stable sensing of H₂S gas. The locally synthesized ZnO/ZnS core-shell nanowires enable an ultracompact-sized device, and Pd nanoparticles improve the sensing performance and reduce the operating temperature (200 °C). The device shows a high sensitivity [(G_gas - G_air)/G_air × 100% = 4491% to 10 ppm], fast response (response/recovery time <100 s) to hydrogen sulfide, and outstanding selectivity (>100 times) to other toxic gases (e.g., carbon monoxide, acetone, ethanol, and toluene). Moreover, vertically synthesized nanowires provide a long bending path, which reduces the mechanical stresses on the structure. The devices showed stable gas sensing performance under 9 mm positive radius of curvature and 5 mm negative radius of curvature. The mechanical robustness of the device was also verified by numerical simulations which showed dramatic decrease of maximum stress and strain to 4.2 and 5.0%, respectively.

Atomic Mechanism in Layer-by-Layer Growth via Surface Reconstruction

Layer-by-layer growth played a critical role in the fine design of novel materials and devices. Although it has been widely studied during materials synthesis, the atomic mechanism of the growth remains unclear due to the lack of direct observation at the atomic scale. Here, we report a new mode in layer-by-layer growth via surface reconstruction on MoO₂ (011) by environmental transmission electron microscopy and density functional theory calculations. Our in situ environmental transmission electron microscopy results demonstrate that the layer-by-layer growth of MoO₂ experiences two steps that occur in an oscillatory manner: (1) the formation of an atomic ledge by transforming a section of the reconstructed layer to the intrinsic surface layer and then (2) the spontaneous reconstruction of the newly formed intrinsic surface section. Thus, the surface reconstruction can be considered as an intermediated phase during the layer-by-layer growth of MoO₂. A similar phenomenon was also observed in the MoO₂ dissolution procedure.

Oxidation and hydrogenation of Pd: suppression of oxidation by prolonged H2 exposure

We investigate the phase transition of a Pd surface in both oxidizing and reducing environments by environmental transmission electron microscopy (ETEM). ETEM allows us to study sequential exposure of Pd to O2 and H2 in the same TEM conditions. First, under ETEM observation, oxidation occurs at step edges but it can also occur at terraces. Second, as the most important result, we observed a novel process where previous exposure to H2 suppresses new oxidation of the Pd surface. Third, we show by electron energy loss spectroscopy (EELS) that this process, suppression of oxidation by previous exposure to H2, is not due to the formation of bulk β-phase Pd hydride. We also demonstrate that this process is not present in Pt. Finally, we discuss the hypothesis to explain this phenomenon: formation of surface-Pd-hydride suppresses the new oxidation. This observation, suppression of oxidation by H2 exposure, may eventually lead to new breakthroughs.

Partially Oxidized Palladium Nanodots for Enhanced Electrocatalytic Carbon Dioxide Reduction

Here we report a partially oxidized palladium nanodot (Pd/PdO_x ) catalyst with a diameter of around 4.5 nm. In aqueous CO₂ -saturated 0.5 m KHCO₃ , the catalyst displays a Faradaic efficiency (FE) of 90 % at -0.55 V vs. reversible hydrogen electrode (RHE) for carbon monoxide (CO) production, and the activity can be retained for at least 24 h. The improved catalytic activity can be attributed to the strong adsorption of CO₂ ^.- intermediate on the Pd/PdO_x electrode, wherein the presence of Pd²⁺ during the electroreduction reaction of CO₂ may play an important role in accelerating the carbon dioxide reduction reaction (CO₂ RR). This study explores the catalytic mechanism of a partially oxidized nanostructured Pd electrocatalyst and provides new opportunities for improving the CO₂ RR performance of metal systems.