The MYTHEN detector for X-ray powder diffraction experiments at the Swiss Light Source

MYTHEN III: advancements in single photon counting detectors for synchrotron powder diffraction experiments

The single photon counting microstrip detector MYTHEN III was developed at the Paul Scherrer Institute to satisfy the increasing demands in detector performance of synchrotron radiation experiments, focusing on time-resolved and on-edge powder diffraction measurements. Similar to MYTHEN II, the detector installed on the Material Science beamline covers 120° in 2θ. It is based on the MYTHEN III.0 readout chip wire-bonded to silicon strip sensors with a pitch of 50 µm, and it provides improved performance and features with respect to the previous version. Taking advantage of the three independent comparators of MYTHEN III, it is possible to obtain an improvement in the maximum count rate capability of the detector at 90% efficiency from 2.9 ± 0.8 Mphotons s-1 strip-1 to 11 ± 2 Mphotons s-1 strip-1 thanks to the detection of pile-up at high photon flux. The readout chip offers additional operation modes such as pump-probe and digital on-chip interpolation. The maximum frame rate is up to 360 kHz in 8-bit mode with dead-time-free readout. The minimum detectable energy of MYTHEN III is 4.3 ± 0.3 keV with a minimum equivalent noise charge (ENC) of 121 ± 8 electrons and a threshold dispersion below 33 ± 10 eV. The energy calibration is affected by temperature by less than 0.5% °C-1. This paper presents a comprehensive overview of the MYTHEN III detector system with performance benchmarks, and highlights the improvements reached in powder diffraction experiments compared with the previous detector generation.

High-throughput and high-resolution powder X-ray diffractometer consisting of six sets of 2D CdTe detectors with variable sample-to-detector distance and innovative automation system

The demand for powder X-ray diffraction analysis continues to increase in a variety of scientific fields, as the excellent beam quality of high-brightness synchrotron light sources enables the acquisition of high-quality measurement data with high intensity and angular resolution. Synchrotron powder diffraction has enabled the rapid measurement of many samples and various in situ/operando experiments in nonambient sample environments. To meet the demands for even higher throughput measurements using high-energy X-rays at SPring-8, a high-throughput and high-resolution powder diffraction system has been developed. This system is combined with six sets of two-dimensional (2D) CdTe detectors for high-energy X-rays, and various automation systems, including a system for automatic switching among large sample environmental equipment, have been developed in the third experimental hutch of the insertion device beamline BL13XU at SPring-8. In this diffractometer system, high-brilliance and high-energy X-rays ranging from 16 to 72 keV are available. The powder diffraction data measured under ambient and various nonambient conditions can be analysed using Rietveld refinement and the pair distribution function. Using the 2D CdTe detectors with variable sample-to-detector distance, three types of scan modes have been established: standard, single-step and high-resolution. A major feature is the ability to measure a whole powder pattern with millisecond resolution. Equally important, this system can measure powder diffraction data with high Q exceeding 30 Å-1 within several tens of seconds. This capability is expected to contribute significantly to new research avenues using machine learning and artificial intelligence by utilizing the large amount of data obtained from high-throughput measurements.

Alkali metal alkoxyborate ester salts; a contemporary look at old compounds

Research into the use of sodium tetraalkoxyborate salts for different chemical applications including synthetic catalysis, hydrogen storage, or battery applications has been investigated, however, understanding of the structural, thermal and electrochemical properties of these salts has been lacking since the 1950s and 1960s. A review of the synthesis, as well as a thorough characterization using 1H NMR, 11B NMR, 13C{1H} NMR, FTIR, XRD, in situ XRD, DSC-TGA, RGA-MS, TPPA, and EIS has newly identified polymorphic phase changes for Na[B(OMe)4], K[B(OMe)4], Li[B(OMe)4], Na[B(OEt)4], Na[B(OBu)4], and Na[B(OiBu)4]. The crystal structure of K[B(OMe)4] was also solved in I41/a (a = 22.337(2) Å, c = 7.648(3) Å, V = 3815.6(4) Å3, ρ = 1.128(1) g cm-3). Ionic conductivity of the different salts was analyzed, however it was found that the compounds with longer alkyl chains had no measurable ionic conductivity compared to the shorter chained samples, Na[B(OMe)4] and K[B(OMe)4] with 9.6 × 10-8 S cm-1 and 1.6 × 10-7 S cm-1, at 114 °C respectively.

Exploring high-throughput synchrotron X-Ray powder diffraction for the structural analysis of pharmaceuticals

Synchrotron radiation offers a host of advanced properties, surpassing conventional laboratory sources with its high brightness, tunable phonon energy, photon beam coherence for advanced X-ray imaging, and a structured time profile, ideal for capturing dynamic atomic and molecular processes. However, these benefits come at the cost of operational complexity and expenses. Three decades ago, synchrotron radiation facilities, while technically open to all scientists, primarily served a limited community. Despite substantial accessibility improvements over the past two decades, synchrotron measurements still do not qualify as routine analyses. The intrinsic complexity of synchrotron science means experiments are pursued only when no alternatives suffice. In recent years, strides have been made in technology transfer offices, intermediate synchrotron-based analytical service companies, and the development of high-throughput synchrotron systems at various facilities, reshaping the perception of synchrotron science. This article investigates the practical application of synchrotron X-Ray Powder Diffraction (s-XRPD) techniques in pharmaceutical analysis. By utilizing concrete examples, we demonstrate how high-throughput systems have the potential to revolutionize s-XRPD applications in the pharmaceutical industry, rapidly generating XRPD patterns of comparable or superior quality to those obtained in state-of-the-art laboratory XRPD, all in less than 5 s. Additional cases featuring well-established pharmaceutical active ingredients (API) and excipients substantiate the concept of high throughput in pharmaceuticals, affirming data quality through structural refinements aligned with literature-derived unit cell parameters. Synchrotron data need not always be state-of-the-art to compete with lab-XRPD data. The key lies in ensuring user-friendliness, reproducibility, accessibility, cost-effectiveness, and the streamlined efforts associated with synchrotron instrumentation to remain highly competitive with their laboratory counterparts.

Coupling to octahedral tilts in halide perovskite nanocrystals induces phonon-mediated attractive interactions between excitons

Understanding the origin of electron-phonon coupling in lead halide perovskites is key to interpreting and leveraging their optical and electronic properties. Here we show that photoexcitation drives a reduction of the lead-halide-lead bond angles, a result of deformation potential coupling to low-energy optical phonons. We accomplish this by performing femtosecond-resolved, optical-pump-electron-diffraction-probe measurements to quantify the lattice reorganization occurring as a result of photoexcitation in nanocrystals of FAPbBr3. Our results indicate a stronger coupling in FAPbBr3 than CsPbBr3. We attribute the enhanced coupling in FAPbBr3 to its disordered crystal structure, which persists down to cryogenic temperatures. We find the reorganizations induced by each exciton in a multi-excitonic state constructively interfere, giving rise to a coupling strength that scales quadratically with the exciton number. This superlinear scaling induces phonon-mediated attractive interactions between excitations in lead halide perovskites.

Structural insight into the cooperativity of spin crossover compounds

Spin-crossover (SCO) compounds are promising materials for a wide variety of industrial applications. However, the fundamental understanding of their nature of transition and its effect on the physical properties are still being fervently explored; the microscopic knowledge of their transition is essential for tailoring their properties. Here an attempt is made to correlate the changes in macroscopic physical properties with microscopic structural changes in the orthorhombic and monoclinic polymorphs of the SCO compound Fe(PM-Bia)2(NCS)2 (PM = N-2'-pyridylmethylene and Bia = 4-aminobiphenyl) by employing single-crystal X-ray diffraction, magnetization and DSC measurements. The dependence of macroscopic properties on cooperativity, highlighting the role of hydrogen bonding, π-π and van der Waals interactions is discussed. Values of entropy, enthalpy and cooperativity are calculated numerically based on the Slichter-Drickamer model. The particle size dependence of the magnetic properties is probed along with the thermal exchange and the kinetic behavior of the two polymorphs based on the dependence of magnetization on temperature scan rate and a theoretical model is proposed for the calculation of the non-equilibrium spin-phase fraction. Also a scan-rate-dependent two-step behavior observed for the orthorhombic polymorph, which is absent for the monoclinic polymorph, is reported. Moreover, it is found that the radiation dose from synchrotron radiation affects the spin-crossover process and shifts the transition region to lower temperatures, implying that the spin crossover can be tuned with radiation damage.

Energy Transfer from Magnetic Iron Oxide Nanoparticles: Implications for Magnetic Hyperthermia

Magnetic iron oxide nanoparticles (IONPs) have gained momentum in the field of biomedical applications. They can be remotely heated via alternating magnetic fields, and such heat can be transferred from the IONPs to the local environment. However, the microscopic mechanism of heat transfer is still debated. By X-ray total scattering experiments and first-principles simulations, we show how such heat transfer can occur. After establishing structural and microstructural properties of the maghemite phase of the IONPs, we built a maghemite model functionalized with aminoalkoxysilane, a molecule used to anchor (bio)molecules to oxide surfaces. By a linear response theory approach, we reveal that a resonance mechanism is responsible for the heat transfer from the IONPs to the surroundings. Heat transfer occurs not only via covalent linkages with the IONP but also through the solvent hydrogen-bond network. This result may pave the way to exploit the directional control of the heat flow from the IONPs to the anchored molecules-i.e., antibiotics, therapeutics, and enzymes-for their activation or release in a broader range of medical and industrial applications.

Total scattering measurements at the Australian Synchrotron Powder Diffraction beamline: capabilities and limitations

This study describes the capabilities and limitations of carrying out total scattering experiments on the Powder Diffraction (PD) beamline at the Australian Synchrotron, ANSTO. A maximum instrument momentum transfer of 19 Å^-1 can be achieved if the data are collected at 21 keV. The results detail how the pair distribution function (PDF) is affected by Q_max, absorption and counting time duration at the PD beamline, and refined structural parameters exemplify how the PDF is affected by these parameters. There are considerations when performing total scattering experiments at the PD beamline, including (1) samples need to be stable during data collection, (2) highly absorbing samples with a μR > 1 always require dilution and (3) only correlation length differences >0.35 Å may be resolved. A case study comparing the PDF atom-atom correlation lengths with EXAFS-derived radial distances of Ni and Pt nanocrystals is also presented, which shows good agreement between the two techniques. The results here can be used as a guide for researchers considering total scattering experiments at the PD beamline or similarly setup beamlines.

Strongly Confined CsPbBr3 Quantum Dots as Quantum Emitters and Building Blocks for Rhombic Superlattices

The success of the colloidal semiconductor quantum dots (QDs) field is rooted in the precise synthetic control of QD size, shape, and composition, enabling electronically well-defined functional nanomaterials that foster fundamental science and motivate diverse fields of applications. While the exploitation of the strong confinement regime has been driving commercial and scientific interest in InP or CdSe QDs, such a regime has still not been thoroughly explored and exploited for lead-halide perovskite QDs, mainly due to a so far insufficient chemical stability and size monodispersity of perovskite QDs smaller than about 7 nm. Here, we demonstrate chemically stable strongly confined 5 nm CsPbBr3 colloidal QDs via a postsynthetic treatment employing didodecyldimethylammonium bromide ligands. The achieved high size monodispersity (7.5% ± 2.0%) and shape-uniformity enables the self-assembly of QD superlattices with exceptional long-range order, uniform thickness, an unusual rhombic packing with an obtuse angle of 104°, and narrow-band cyan emission. The enhanced chemical stability indicates the promise of strongly confined perovskite QDs for solution-processed single-photon sources, with single QDs showcasing a high single-photon purity of 73% and minimal blinking (78% "on" fraction), both at room temperature.

A compact-rigid multi-analyser for energy and angle filtering of high-resolution X-ray experiments. Part 2. Efficiency of a single-crystal-comb

Diffraction instruments using filtering by one or several analyser crystals exist since the 1980s and 1990s at synchrotron radiation sources, but, due to its low efficiency, this filtering is little used on laboratory sources. In order to overcome this limitation, the efficiency of a small diffraction filtering multi-analyzer block (MAD block) realized with a `single-crystal-comb' curved on a rigid support is demonstrated here. The geometry of this curved surface is logarithmic spiral and is optimized to allow multi-filtering over a relatively important diffraction angular range and to be also applicable over an X-ray spectral range. The efficiency of such a small rigid-compact MAD block consisting of this single-crystal-comb generating 20-50 Si(111) single-crystal blades, associated with a block of Soller collimators, is demonstrated. The angle between each crystal is 0.1°, so the measurement range of the comb is 2-5°. The geometry of this system has been optimized for operation with a synchrotron X-ray source over an energy range of 22 keV to 46 keV and could be used with laboratory X-ray sources (Ag Kα<sub>1</sub>, 22.1 keV). This MAD block complements and exploits the qualities of the `photon-counting' detectors which have very low intrinsic noise. Their joint efficacy is supported by powder pattern measurements of a LaB₆ reference sample and of several heterogeneous samples of cultural heritage materials, carried out at 22 keV on the D2AM beamline at the ESRF. Their signal-to-noise ratio is excellent (1000/1) and allows the detection thresholds of the measurements (from 3-1% to 0.1%) to detect minor phases in the studies of `real' heterogeneous materials to be drastically improved.

Electron density and thermal motion of diamond at elevated temperatures

The electron density and thermal motion of diamond are determined at nine temperatures between 100 K and 1000 K via synchrotron powder X-ray diffraction (PXRD) data collected on a high-accuracy detector system. Decoupling of the thermal motion from the thermally smeared electron density is performed via an iterative Wilson-Hansen-Coppens-Rietveld procedure using theoretical static structure factors from density functional theory (DFT) calculations. The thermal motion is found to be harmonic and isotropic in the explored temperature range, and excellent agreement is observed between experimental atomic displacement parameters (ADPs) and those obtained via theoretical harmonic phonon calculations (HPC), even at 1000 K. The Debye temperature of diamond is determined experimentally to be Θ_D = 1883 (35) K. A topological analysis of the electron density explores the temperature dependency of the electron density at the bond critical point. The properties are found to be constant throughout the temperature range. The robustness of the electron density confirms the validity of the crystallographic convolution approximation for diamond in the explored temperature range.

A compact-rigid multi-analyser for energy and angle filtering of high-resolution X-ray experiments. Part 1. Principles and implementation

Diffraction and spectroscopy instruments using a filtering process with several analyser crystals have existed for about 30 years at synchrotron radiation sources, but they are difficult to use on laboratory sources. Several diffraction multi-filtering systems for powder diffraction experiments have been studied and optimized, in order to show the relevance, simplicity and efficiency of their implementation. Optical filter systems containing one or many diffracting elements, precisely positioned in a rigid manner on a logarithmic spiral surface and having a stability that allows high resolution and high sensitivity to powder diffraction experiments, have been developed. After having tested prototypes with various geometries, we present in particular the realization of a small rigid-compact multi-analyser comb that allows 20-50 measurements on synchrotron radiation sources to be filtered in parallel, but also and especially that can be adapted on laboratory X-ray sources (Ag Kα₁) to increase by an order of magnitude the intensities and resolutions of the measurements. Such a rigid-compact multi-analyser block can advantageously be associated with `photon-counting' 1D and 2D detectors in order to drastically improve the detection thresholds of powder diffraction measurements to better than 0.1%, which allows the detection/quantification/analysis of minor phases in studies of `real' complex materials.

Structure and Surface Relaxation of CeO2 Nanoparticles Unveiled by Combining Real and Reciprocal Space Total Scattering Analysis

We present a combined real and reciprocal space structural and microstructural characterization of CeO₂ nanoparticles (NPs) exhibiting different crystallite sizes; ~3 nm CeO₂ NPs were produced by an inverse micellae wet synthetic path and then annealed at different temperatures. X-ray total scattering data were analyzed by combining real-space-based Pair Distribution Function analysis and the reciprocal-space-based Debye Scattering Equation method with atomistic models. Subtle atomic-scale relaxations occur at the nanocrystal surface. The structural analysis was corroborated by ab initio DFT and force field calculations; micro-Raman and electron spin resonance added important insights to the NPs' defective structure. The combination of the above techniques suggests a core-shell like structure of ultrasmall NPs. These exhibit an expanded outer shell having a defective fluorite structure, while the inner shell is similar to the bulk structure. The presence of partially reduced O2-δ species testifies to the high surface activity of the NPs. On increasing the annealing temperature, the particle dimensions increase, limiting disorder as a consequence of the progressive surface-to-volume ratio reduction.

Na2B11H13 and Na11(B11H14)3(B11H13)4 as potential solid-state electrolytes for Na-ion batteries

Solid-state sodium batteries have attracted great attention owing to their improved safety, high energy density, large abundance and low cost of sodium compared to the current Li-ion batteries. Sodium-boranes have been studied as potential solid-state electrolytes and the search for new materials is necessary for future battery applications. Here, a facile and cost-effective solution-based synthesis of Na₂B₁₁H₁₃ and Na₁₁(B₁₁H₁₄)₃(B₁₁H₁₃)₄ is demonstrated. Na₂B₁₁H₁₃ presents an ionic conductivity in the order of 10^-7 S cm^-1 at 30 °C, but undergoes an order-disorder phase transition and reaches 10^-3 S cm^-1 at 100 °C, close to that of liquids and the solid-state electrolyte Na-β-Al₂O₃. The formation of a mixed-anion solid-solution, Na₁₁(B₁₁H₁₄)₃(B₁₁H₁₃)₄, partially stabilises the high temperature structural polymorph observed for Na₂B₁₁H₁₃ at room temperature and it exhibits Na⁺ conductivity higher than its constituents (4.7 × 10^-5 S cm^-1 at 30 °C). Na₂B₁₁H₁₃ and Na₁₁(B₁₁H₁₄)₃(B₁₁H₁₃)₄ exhibit an oxidative stability limit of 2.1 V vs. Na⁺/Na.

Effects of Structural and Microstructural Features on the Total Scattering Pattern of Nanocrystalline Materials

Atomic- and nanometer-scale features of nanomaterials have a strong influence on their chemical and physical properties and a detailed description of these elements is a crucial step in their characterization. Total scattering methods, in real and reciprocal spaces, have been established as fundamental techniques to retrieve this information. Although the impact of microstructural features, such as defectiveness of different kinds, has been extensively studied in reciprocal space, disentangling these effects from size- and morphology-induced properties, upon downsizing, is not a trivial task. Additionally, once the experimental pattern is Fourier transformed to calculate the pair distribution function, the direct fingerprint of structural and microstructural features is severely lost and no modification of the histogram of interatomic distances derived therefrom is clearly discussed nor considered in the currently available protocols. Hereby, starting from atomistic models of a prototypical system (cadmium selenide), we simulate multiple effects on the atomic pair distribution function, obtained from reciprocal space patterns computed through the Debye scattering equation. Size and size dispersion effects, as well as different structures, morphologies, and their interplay with several kinds of planar defects, are explored, aiming at identifying the main (measurable and informative) fingerprints of these features on the total scattering pattern in real and reciprocal spaces, highlighting how, and how much, they become evident when comparing different cases. The results shown herein have general validity and, as such, can be further extended to other classes of nanomaterials.

Structural Analysis of Molecular Materials Using the Pair Distribution Function

This is a review of atomic pair distribution function (PDF) analysis as applied to the study of molecular materials. The PDF method is a powerful approach to study short- and intermediate-range order in materials on the nanoscale. It may be obtained from total scattering measurements using X-rays, neutrons, or electrons, and it provides structural details when defects, disorder, or structural ambiguities obscure their elucidation directly in reciprocal space. While its uses in the study of inorganic crystals, glasses, and nanomaterials have been recently highlighted, significant progress has also been made in its application to molecular materials such as carbons, pharmaceuticals, polymers, liquids, coordination compounds, composites, and more. Here, an overview of applications toward a wide variety of molecular compounds (organic and inorganic) and systems with molecular components is presented. We then present pedagogical descriptions and tips for further implementation. Successful utilization of the method requires an interdisciplinary consolidation of material preparation, high quality scattering experimentation, data processing, model formulation, and attentive scrutiny of the results. It is hoped that this article will provide a useful reference to practitioners for PDF applications in a wide realm of molecular sciences, and help new practitioners to get started with this technique.

The CirPAD, a circular 1.4 M hybrid pixel detector dedicated to X-ray diffraction measurements at Synchrotron SOLEIL

One of the challenges of all synchrotron facilities is to offer the highest performance detectors for all their specific experiments, in particular for X-ray diffraction imaging and its high throughput data collection. In that context, the DiffAbs beamline, the Detectors and the Design and Engineering groups at Synchrotron SOLEIL, in collaboration with ImXPAD and Cegitek companies, have developed an original and unique detector with a circular shape. This detector is based on the hybrid pixel photon-counting technology and consists of the specific assembly of 20 hybrid pixel array detector (XPAD) modules. This article aims to demonstrate the main characteristics of the CirPAD (for Circular Pixel Array Detector) and its performance - i.e. excellent pixel quality, flat-field correction, high-count-rate performance, etc. Additionally, the powder X-ray diffraction pattern of an LaB6 reference sample is presented and refined. The obtained results demonstrate the high quality of the data recorded from the CirPAD, which allows the proposal of its use to all scientific communities interested in performing experiments at the DiffAbs beamline.

Thermal and Electrochemical Interface Compatibility of a Hydroborate Solid Electrolyte with 3 V-Class Cathodes for All-Solid-State Sodium Batteries

Thermal stability of solid electrolytes and their compatibility with battery electrodes are key factors to ensure stable cycling and high operational safety of all-solid-state batteries. Here, we study the compatibility of a hydroborate solid electrolyte Na₄(B₁₂H₁₂)(B₁₀H₁₀) with 3 V-class cathode active materials: NaCrO₂, NaMnO₂, and NaFeO₂. Among these layered sodium transition metal oxide cathodes, NaCrO₂ shows the highest thermal compatibility in contact with the hydroborate solid electrolyte up to 525 °C in the discharged state. Furthermore, the electrolyte remains intact upon the internal thermal decomposition of the charged, that is, desodiated, cathode (Na_0.5CrO₂) above 250 °C, demonstrating the potential for highly safe hydroborate-based all-solid-state batteries with a wide operating temperature range. The experimentally determined onset temperatures of thermal decomposition of Na₄(B₁₂H₁₂)(B₁₀H₁₀) in contact with 3 V-class cathodes surpass those of sulfide and selenide solid electrolytes, exceeding previous thermodynamic calculations. Our results also highlight the need to identify relevant decomposition pathways of hydroborates to enable more valid theoretical predictions.

Optimizing pyrolysis conditions for recycling pig bones into phosphate fertilizer

Selecting pyrolysis parameters for recycling P-rich and hazardous biowastes, such as bones, into fertilizers is still a challenge. Our objective was to improve pyrolysis procedures of pig bones for the production of P fertilizers. Bone chars were produced by pyrolysis at 400, 550, or 800 °C with no gas addition; 550 and 800 °C under N₂; 800 °C under steam flux, using calcination at 800 °C as control treatment. Synchrotron-based X-ray diffraction and X-ray absorption near edge structure spectroscopy at the P and Ca K- and L-edges showed that these bone chars were largely composed of hydroxyapatite. Hydroxyapatite crystallization was inhibited by pyrolysis conducted in the absence of oxygen at 400, 550, or 800 °C, either under no gas or under N₂ flux. The clogging of pores by lack of organic compounds removal was hypothesized to cause low surface area of 400 °C bone char, resulting in a fertilizer with citric-acid soluble P as low as calcination, while 550 and 800 °C bone chars obtained in absence of oxygen showed greater porosity, surface area, and citric acid-soluble P than steamed or calcined samples at 800 °C. Although extractable phosphate in water and neutral-ammonium-citrate showed trends comparable to those from citric acid, it was negligible for all heated materials. Since it is possible to produce bone chars with different chemical, physical and crystallographic properties by managing pyrolysis conditions, bone chars can be designed to increase their suitability as P fertilizers for different purposes, such as high solubility or slow P release.

Synchrotron total-scattering data applicable to dual-space structural analysis

Synchrotron powder X-ray diffraction (PXRD) is a well established technique for investigating the atomic arrangement of crystalline materials. At modern beamlines, X-ray scattering data can be collected in a total-scattering setting, which additionally opens up the opportunity for direct-space structural analysis through the atomic pair distribution function (PDF). Modelling of PXRD and PDF data is typically carried out separately, but employing a concurrent structural model to both direct- and reciprocal-space data has the possibility to enhance total-scattering data analysis. However, total-scattering measurements applicable to such dual-space analyses are technically demanding. Recently, the technical demands have been fulfilled by a MYTHEN microstrip detector system (OHGI), which meets the stringent requirements for both techniques with respect to Q range, Q resolution and dynamic range. In the present study, we evaluate the quality of total-scattering data obtained with OHGI by separate direct- and reciprocal-space analysis of Si. Excellent agreement between structural parameters in both spaces is found, demonstrating that the total-scattering data from OHGI can be utilized in dual-space structural analysis e.g. for in situ and operando measurements.

The lower energy diffraction and scattering side-bounce beamline for materials science at the Canadian Light Source

A new diffraction beamline for materials science has been built at the Canadian Light Source synchrotron. The X-ray source is an in-vacuum wiggler with a 2.5 T peak magnetic field at 5.2 mm gap. The optical configuration includes a toroidal mirror, a single side-bounce Bragg monochromator, and a cylindrical mirror, producing a sub-150 µm vertical × 500 µm horizontal focused beam with a photon energy range of 7-22 keV and a flux of 10¹² photons per second at the sample position. Three endstations are currently open to general users, and the techniques available include high-resolution powder diffraction, small molecule crystallography, X-ray reflectivity, in situ rapid thermal annealing, and SAXS/WAXS. The beamline design parameters, calculated and measured performance, and initial experimental results are presented to demonstrate the capabilities for materials science.

New perspectives in macromolecular powder diffraction using single-photon-counting strip detectors: high-resolution structure of the pharmaceutical peptide octreotide

Advances in instrumentation, as well as the development of powerful crystallographic software have significantly facilitated the collection of high-resolution diffraction data and have made X-ray powder diffraction (XRPD) particularly useful for the extraction of structural information; this is true even for complex molecules, especially when combined with synchrotron radiation. In this study, in-line with past instrumental profile studies, an improved data collection strategy exploiting the MYTHEN II detector system together with significant beam focusing and tailored data collection options was introduced and optimized for protein samples at the Material Science beamline at the Swiss Light Source. Polycrystalline precipitates of octreotide, a somatostatin analog of particular pharmaceutical interest, were examined with this novel approach. XRPD experiments resulted in high angular and d-spacing (1.87 Å) resolution data, from which electron-density maps of enhanced quality were extracted, revealing the molecule's structural properties. Since microcrystalline precipitates represent a viable alternative for administration of therapeutic macromolecules, XRPD has been acknowledged as the most applicable tool for examining a wide spectrum of physicochemical properties of such materials and performing studies ranging from phase identification to complete structural characterization.

Spin-Crossover 2-D Hofmann Frameworks Incorporating an Amide-Functionalized Ligand: N-(pyridin-4-yl)benzamide

Two analogous 2-D Hofmann-type frameworks, which incorporate the novel ligand N-(pyridin-4-yl)benzamide (benpy) [FeII(benpy)2M(CN)4]·2H2O (M = Pd (Pd(benpy)) and Pt (Pt(benpy))) are reported. The benpy ligand was explored to facilitate spin-crossover (SCO) cooperativity via amide group hydrogen bonding. Structural analyses of the 2-D Hofmann frameworks revealed benpy-guest hydrogen bonding and benpy-benpy aromatic contacts. Both analogues exhibited single-step hysteretic spin-crossover (SCO) transitions, with the metal-cyanide linker (M = Pd or Pt) impacting the SCO spin-state transition temperature and hysteresis loop width (Pd(benpy): T½↓↑: 201, 218 K, ∆T: 17 K and Pt(benpy): T½↓↑: 206, 226 K, ∆T: 20 K). The parallel structural and SCO changes over the high-spin to low-spin transition were investigated using variable-temperature, single-crystal, and powder X-ray diffraction, Raman spectroscopy, and differential scanning calorimetry. These studies indicated that the ligand–guest interactions facilitated by the amide group acted to support the cooperative spin-state transitions displayed by these two Hofmann-type frameworks, providing further insight into cooperativity and structure–property relationships.

Multipole electron densities and structural parameters from synchrotron powder X-ray diffraction data obtained with a MYTHEN detector system (OHGI)

Powder X-ray diffraction has some inherent advantages over traditional single-crystal X-ray diffraction in accurately determining electron densities and structural parameters due to the lower requirements for sample crystallinity, simpler corrections and measurement simultaneity. For some simple inorganic materials, it has been shown that these advantages can compensate for disadvantages such as peak overlap and error-prone background subtraction. Although it is challenging to extend powder X-ray diffraction-based electron-density studies to organic materials with significant peak overlap, previous results using a dedicated vacuum diffractometer with a large image-plate camera (AVID) demonstrated that it can be done. However, the vacuum setup with the off-line detector system was found to prohibit a widespread use. Fast microstrip detectors, which have been employed at a number of powder diffraction beamlines, have the potential to facilitate electron-density studies. Nevertheless, no electron-density studies even for materials with slight peak overlap have been performed with microstrip detectors. One of the most critical problems has been a difference in sensitivity between microstrip channels, which substantially defines the dynamic range of a detector. Recently, a robust approach to this problem has been developed and applied to a total scattering measurement system (OHGI) with 15 MYTHEN microstrip modules. In the present study, synchrotron powder X-ray diffraction data obtained with OHGI are evaulated in terms of multipole electron densities and structural parameters (atomic positions and displacement parameters). These results show that, even without a dedicated setup and perfect samples, electron-density modelling can be carried out on high-quality powder X-ray diffraction data. However, it was also found that the required prior information about the sample prohibits widespread use of the method. With the presently obtainable data quality, electron densities of molecular crystals in general are not reliably obtained from powder data, but it is an excellent, possibly superior, alternative to single-crystal measurements for small-unit-cell inorganic solids. If aspherical atomic scattering factors can be obtained from other means (multipole databases, theoretical calculations), then atomic positions (including for hydrogen) and anisotropic atomic displacement parameters (non-hydrogen atoms) of excellent accuracy can be refined from synchrotron powder X-ray diffraction data on organic crystals.

The structure of kaliophilite KAlSiO4, a long-lasting crystallographic problem

Kaliophilite is a feldspathoid mineral found in two Italian magmatic provinces and represents one of the 12 known phases with composition close to KAlSiO4. Despite its apparently simple formula, the structure of this mineral revealed extremely complex and resisted structure solution for more than a century. Samples from the Vesuvius-Monte Somma and Alban Hills volcanic areas were analyzed through a multi-technique approach, and finally the crystal structure of kaliophilite was solved using 3D electron diffraction and refined against X-ray diffraction data of a twinned crystal. Results were also ascertained by the Rietveld method using synchrotron powder intensities. It was found that kaliophilite crystallizes in space group P3 with unit-cell parameters a = 27.0597 (16), c = 8.5587 (6) Å, V = 5427.3 (7) Å3 and Z = 54. The kaliophilite framework is a variant of the tridymite topology, with alternating SiO4 and AlO4 tetrahedra forming sheets of six-membered rings (63 nets), which are connected along [001] by sharing the apical oxygen atoms. Considering the up (U) and down (D) orientations of the linking vertex, kaliophilite is the first framework that contains three different ring topologies: nine (1-3-5) (UDUDUD) rings, six (1-2-3) (UUUDDD) rings and twelve (1-2-4) (UUDUDD) rings. This results in a relatively open (19.9 tetrahedra nm-3) channel system with multiple connections between the double six-ring cavities. Such a framework requires a surprisingly large unit cell, 27 times larger than the cell of kalsilite, the simplest phase with the same composition. The occurrence of some Na for K substitution (3-10%) may be related to the characteristic structural features of kaliophilite. Micro-twinning, pseudo-symmetries and anisotropic hkl-dependent peak broadening were also detected, and they may account for the elusive character of the kaliophilite crystal structure.

Insulin polymorphism induced by two polyphenols: new crystal forms and advances in macromolecular powder diffraction

This study focuses on the polymorphism of human insulin (HI) upon the binding of the phenolic derivativesp-coumaric acid ortrans-resveratrol over a wide pH range. The determination of the structural behaviour of HI via X-ray powder diffraction (XRPD) and single-crystal X-ray diffraction (SCXRD) is reported. Four distinct polymorphs were identified, two of which have not been reported previously. The intermediate phase transitions are discussed. One of the novel monoclinic polymorphs displays the highest molecular packing among insulin polymorphs of the same space group to date; its structure was elucidated by SCXRD. XRPD data collection was performed using a variety of instrumental setups and a systematic comparison of the acquired data is presented. A laboratory diffractometer was used for screening prior to high-resolution XRPD data collection on the ID22 beamline at the European Synchrotron Radiation Facility. Additional measurements for the most representative samples were performed on the X04SA beamline at the Swiss Light Source (SLS) using the MYTHEN II detector, which allowed the detection of minor previously untraceable impurities and dramatically improved thed-spacing resolution even for poorly diffracting samples.

On-demand correction for X-ray response non-uniformity in microstrip detectors by a data-driven approach

A statistical approach, which was previously developed to correct scattering data for X-ray response non-uniformity (XRNU) in microstrip detectors, has been improved to significantly reduce the correcting time. The improved algorithm has succeeded in increasing the utilization rate of data acquired for reference intensity to 98%. As a result, the correcting time was reduced from half a day to half an hour, which was shorter than the typical measuring time of a sample. Moreover, the present approach was found to yield better correction results than the previous one. The data-driven approach enabled the on-demand correction for XRNU according to the detector and experimental settings. The present study will encourage the correction of scattering data for XRNU in area detectors.

Full reciprocal-space mapping up to 2000 K under controlled atmosphere: the multipurpose QMAX furnace

A furnace that covers the temperature range from room temperature up to 2000 K has been designed, built and implemented on the D2AM beamline at the ESRF. The QMAX furnace is devoted to the full exploration of the reciprocal hemispace located above the sample surface. It is well suited for symmetric and asymmetric 3D reciprocal space mapping. Owing to the hemispherical design of the furnace, 3D grazing-incidence small- and wide-angle scattering and diffraction measurements are possible. Inert and reactive experiments can be performed at atmospheric pressure under controlled gas flux. It is demonstrated that the QMAX furnace allows monitoring of structural phase transitions as well as microstructural evolution at the nanoscale, such as self-organization processes, crystal growth and strain relaxation. A time-resolved in situ oxidation experiment illustrates the capability to probe the high-temperature reactivity of materials.

Fast continuous measurement of synchrotron powder diffraction synchronized with controlling gas and vapour pressures at beamline BL02B2 of SPring-8

A gas- and vapour-pressure control system synchronized with the continuous data acquisition of millisecond high-resolution powder diffraction measurements was developed to study structural change processes in gas storage and reaction materials such as metal organic framework compounds, zeolite and layered double hydroxide. The apparatus, which can be set up on beamline BL02B2 at SPring-8, mainly comprises a pressure control system of gases and vapour, a gas cell for a capillary sample, and six one-dimensional solid-state (MYTHEN) detectors. The pressure control system can be remotely controlled via developed software connected to a diffraction measurement system and can be operated in the closed gas and vapour line system. By using the temperature-control system on the sample, high-resolution powder diffraction data can be obtained under gas and vapour pressures ranging from 1 Pa to 130 kPa in temperatures ranging from 30 to 1473 K. This system enables one to perform automatic and high-throughput in situ X-ray powder diffraction experiments even at extremely low pressures. Furthermore, this developed system is useful for studying crystal structures during the adsorption/desorption processes, as acquired by millisecond and continuous powder diffraction measurements. The acquisition of diffraction data can be synchronized with the control of the pressure with a high frame rate of up to 100 Hz. In situ and time-resolved powder diffraction measurements are demonstrated for nanoporous Cu coordination polymer in various gas and vapour atmospheres.

Structure, Morphology, and Faceting of TiO2 Photocatalysts by the Debye Scattering Equation Method. The P25 and P90 Cases of Study

Characterization of functional nanocrystalline materials in terms of quantitative determination of size, size dispersion, type, and extension of exposed facets still remains a challenging task. This is particularly the case of anisotropically shaped nanocrystals (NCs) like the TiO₂ photocatalysts. Here, commercially available P25 and P90 titania nanopowders have been characterized by wide-angle X-ray total scattering techniques. Synchrotron data were modelled by the reciprocal space-based Debye scattering equation (DSE) method using atomistic models of NC populations (simultaneously carrying atomic and nanoscale structural features) for both anatase and rutile phases. Statistically robust descriptors are provided of size, morphology, and {101} vs. {001} facet area of truncated tetragonal bipyramids for anatase, jointly to polymorph quantification. The effects of using the proper NC shape on the X-ray diffraction pattern are analyzed in depth through DSE simulations by considering variable bipyramid aspect ratios (resulting in different {101} vs. {001} surface) and relative dispersion in a bivariate manner. We demonstrate that using prismatic NCs having equal volume and aspect ratio as bipyramids provides reasonably accurate sizes and {101} and {001} surface areas of the parent morphology.

Crystal Structure, Morphology, and Surface Termination of Cyan-Emissive, Six-Monolayers-Thick CsPbBr3 Nanoplatelets from X-ray Total Scattering

Highly anisotropic colloidal CsPbBr₃ nanoplatelets (NPLs) represent an appealing class of colloidal quantum wells with enhanced light emissivity. Strong quantum confinement imposed by the small platelet thickness and atomic flatness gives rise to enhanced oscillator strength, higher exciton binding energy, and narrow emission linewidth. While discrete thicknesses manifest themselves in discrete bandgap energies, fine-tuning of the emission energy can be achieved by compositional modulations. Here we address one of the most debated aspects of perovskite nanoplatelets: their crystal structure. Starting with the direct imaging by high-resolution electron microscopy (providing a clue on the pseudocubic faceting of the NPLs), we focus the study on X-ray total scattering techniques, based on the Debye scattering equation (DSE) approach, to obtain better atomistic insight. The nanoplatelets are six-monolayers thick and exhibit an orthorhombic structure. A thorough structure-morphology characterization unveils a specific orientation of the axial and equatorial bromides of the PbBr₆ octahedra versus the NPLs thickness; we found that {010} and {101} planes of the orthorhombic CsPbBr₃ lattice (Pnma space group) correspond to the six facets of the NPL, with basal planes being of {101} type. The NPLs undergo a lattice relaxation in comparison to cuboidal CsPbBr₃ NCs; the major deformation is observed in the axial direction, which suggests a structural origin of the higher compliance along the b axis. The DSE-based analysis also supports a CsBr surface termination model, with half Cs sites and a half (or slightly more) Br sites vacant.

Verification of the de Wolff hypothesis concerning the symmetry of β-MnO2

The symmetry lowering from tetragonal to orthorhombic is demonstrated using high-resolution diffraction and also justified by using the magnetic superspace groups formalism for the rutile-type compound β-MnO₂. The (lower) orthorhombic symmetry is observed at temperatures both below and above the Néel temperature. The magnetic ordering of β-MnO₂ is of spin density type and not screw-type helical. The results support the de Wolff [Acta Cryst. (1959), 12, 341-345] hypothesis about the orthorhombic symmetry of β-MnO₂.

Development of low-energy X-ray detectors using LGAD sensors

Recent advances in segmented low-gain avalanche detectors (LGADs) make them promising for the position-sensitive detection of low-energy X-ray photons thanks to their internal gain. LGAD microstrip sensors fabricated by Fondazione Bruno Kessler have been investigated using X-rays with both charge-integrating and single-photon-counting readout chips developed at the Paul Scherrer Institut. In this work it is shown that the charge multiplication occurring in the sensor allows the detection of X-rays with improved signal-to-noise ratio in comparison with standard silicon sensors. The application in the tender X-ray energy range is demonstrated by the detection of the sulfur K_α and K_β lines (2.3 and 2.46 keV) in an energy-dispersive fluorescence spectrometer at the Swiss Light Source. Although further improvements in the segmentation and in the quantum efficiency at low energy are still necessary, this work paves the way for the development of single-photon-counting detectors in the soft X-ray energy range.

Multipole electron densities and atomic displacement parameters in urea from accurate powder X-ray diffraction

Electron density determination based on structure factors obtained through powder X-ray diffraction has so far been limited to high-symmetry inorganic solids. This limit is challenged by determining high-quality structure factors for crystalline urea using a bespoke vacuum diffractometer with imaging plates. This allows the collection of data of sufficient quality to model the electron density of a molecular system using the multipole method. The structure factors, refined parameters as well as chemical bonding features are compared with results from the high-quality synchrotron single-crystal study by Birkedal et al. [Acta Cryst. (2004), A60, 371-381] demonstrating that powder X-ray diffraction potentially provides a viable alternative for electron density determination in simple molecular crystals where high-quality single crystals are not available.

Transforming X-ray detection with hybrid photon counting detectors

Hybrid photon counting (HPC) detectors have radically transformed basic research at synchrotron light sources since 2006. They excel at X-ray diffraction applications in the energy range from 2 to 100 keV. The main reasons for their superiority are the direct detection of individual photons and the accurate determination of scattering and diffraction intensities over an extremely high dynamic range. The detectors were first adopted in macromolecular crystallography where they revolutionized data collection. They were soon also used for small-angle scattering, coherent scattering, powder X-ray diffraction, spectroscopy and increasingly high-energy applications. Here, we will briefly survey the history of HPC detectors, explain their technology and then show in detail how improved detection has transformed a wide range of experimental techniques. We will end with an outlook to the future, which will probably see HPC technology find even broader use, for example, in electron microscopy and medical applications. This article is part of the theme issue 'Fifty years of synchrotron science: achievements and opportunities'.

A statistical approach to correct X-ray response non-uniformity in microstrip detectors for high-accuracy and high-resolution total-scattering measurements

An unbiased approach to correct X-ray response non-uniformity in microstrip detectors has been developed based on the statistical estimation that the scattering intensity at a fixed angle from an object is expected to be constant within the Poisson noise. Raw scattering data of SiO₂ glass measured by a microstrip detector module was found to show an accuracy of 12σ_PN at an intensity of 10⁶ photons, where σ_PN is the standard deviation according to the Poisson noise. The conventional flat-field calibration has failed in correcting the data, whereas the alternative approach used in this article successfully improved the accuracy from 12σ_PN to 2σ_PN. This approach was applied to total-scattering data measured by a gapless 15-modular detector system. The quality of the data is evaluated in terms of the Bragg reflections of Si powder, the diffuse scattering of SiO₂ glass, and the atomic pair distribution function of TiO₂ nanoparticles and Ni powder.

A dilute gold nanoparticle suspension as small-angle X-ray scattering standard for an absolute scale using an extended Guinier approximation

In this article, a practical procedure for absolute intensity calibration for small-angle scattering (SAXS) studies on liquid microjets is established. A gold nanoparticle suspension is used as standard so that the intercept at Q = 0 of the SAXS scattering curve provides a scaling reference. In order to obtain the most precise extrapolation at Q = 0, an extension of the Guinier approximation has been used, with a second-order term in the fit that adapts to a larger Q range.

Revealing the role of microstructure architecture on strength and ductility of Ni microwires by in-situ synchrotron X-ray diffraction

Deformation mechanisms of cold drawn and electropolished nickel microwires are studied by performing in-situ monotonous and cyclic tensile tests under synchrotron radiation. X-ray diffraction tests allow probing elastic strains in the different grain families and establishing a link with the deformation mechanisms taking place within the microwires. The measurements were carried out on several microwires with diameters ranging from as-drawn 100 µm down to 40 µm thinned down by electropolishing. The as-drawn wires exhibit a core-shell microstructure with <111> fiber texture dominant in core and heterogeneous dual fiber texture <111> and <100> in the shell. Reduction of specimen size by electropolishing results in a higher yield stress and tensile strength along with reduced ductility. In-situ XRD analysis revealed that these differences are linked to the global variation in microstructure induced by shell removal with electropolishing, which in turn affects the load sharing abilities of grain families. This study thus proposes a new way to increase ductility and retain strength in nickel microwires across different diameters by tuning the microstructure architecture.

Understanding the structure and dynamics of cationic surfactants from studies of pure solid phases

Unravelling the phase behaviour of n-alkyltrimethylammonium bromides (C₁₀ to C₁₈): from tight-packed interdigitation to rotational disorder with increasing temperature.

X-ray radiation-induced amorphization of metal–organic frameworks

Accumulation of radiation damage from synchrotron X-rays leads to complete amorphization of the initially crystalline metal–organic frameworks ZIF-4, ZIF-62, and ZIF-zni. The mechanism of this transformation is studied as a function of time and temperature and is shown to be non-isokinetic.

Size-Dependent Fault-Driven Relaxation and Faceting in Zincblende CdSe Colloidal Quantum Dots

Surface chemistry and core defects are known to play a prominent role in governing the photophysical properties of nanocrystalline semiconductors. Nevertheless, investigating them in small nanocrystals remains a complex task. Here, by combining X-ray scattering techniques in the wide- and small-angle regions and using the Debye scattering equation (DSE) method of analysis, we unveil a high density of planar defects in oleate-terminated zincblende (ZB) CdSe colloidal quantum dots (QDs) and size-dependent faceting within a square-cuboid morphology. Atomistic models of faulted ZB nanocrystals, based on the probabilistic stacking of CdSe layers in cubic and hexagonal sequences, and data analysis point to the preferential location of faults near the center of nanocrystals. By finely modeling faulting and morphological effects on the X-ray scattering pattern, a relaxation of the Cd-Se bond distance parallel to the stacking direction, up to +3% (2.71 Å) with respect to the reference bulk value (2.63 Å), is detected, at the cubic/hexagonal transitions. The smallest nanocrystals show cubic {100} facets; {111} facets appear above 4 nm and progressively extend at larger sizes. These structural and morphological features likely vary depending on the synthesis conditions; nevertheless, since planar defects are nearly ubiquitous in CdSe QDs, the modeling approach here presented has a general validity. This work also points to the great potential of combining small- and wide-angle X-ray scattering and DSE-modeling techniques in gaining important knowledge on atomic-scale defects of semiconductor nanocrystals, underpinning the comprehension of the impact of structural defectiveness on the exciting properties of these QDs.

Applications of Powder X-Ray Diffraction in Small Molecule Pharmaceuticals: Achievements and Aspirations

Since the discovery of X-ray diffraction and its potential to elucidate crystal symmetry, powder X-ray diffraction has found diverse applications in the field of pharmaceutical sciences. This review summarizes significant achievements of the technique during various stages of dosage form development. Improved understanding of the principle involved and development of automated hardware and reliable software have led to increased instrumental sensitivity and improved data analysis. These advances continue to expand the applications of powder X-ray diffraction to emerging research fields such as amorphous systems, mechanistic understanding of phase transformations, and "Quality by Design" in formulation development.

(Al,Mg)3La: a new phase in the Mg-Al-La system

During an investigation of the Mg-rich end of the Mg-Al-La system, a new ternary phase with the composition of (Al,Mg)₃La was identified. The crystal structure of this phase was determined by conventional X-ray powder diffraction and transmission electron microscopy analysis and refined using high-resolution X-ray powder diffraction. The (Al,Mg)₃La phase is found to have an orthorhombic structure with a space group of C222₁ and lattice parameters of a = 4.3365 (1) Å, b = 18.8674 (4) Å and c = 4.4242 (1) Å, which is distinctly different from the binary Al₃La phase (P6₃/mmc). The resolved structure of the (Al,Mg)₃La phase is further verified by high-angle annular dark-field scanning transmission electron microscopy.

X-ray diffractometer for the investigation of temperature- and magnetic field-induced structural phase transitions

This article reports the development and characterization of a laboratory-based high-resolution X-ray powder diffractometer equipped with a 5.5 T magnet and closed-cycle helium cryostat that is primarily designed for the investigation of magneto-structural phase transitions. Unique features of the diffractometer include the position-sensitive detector, allowing the collection of an entire diffraction pattern at once, and the high energy resolution with Mo Kα 1 radiation. The ability to utilize a lower energy resolution but higher photon flux by switching to an X-ray mirror monochromator makes it a versatile setup for a variety of compounds. In this contribution, details of the design and performance of the instrument are presented along with its specifications.

Evaluation of the UFXC32k photon-counting detector for pump-probe experiments using synchrotron radiation

This paper presents the performance of a single-photon-counting hybrid pixel X-ray detector with synchrotron radiation. The camera was evaluated with respect to time-resolved experiments, namely pump-probe-probe experiments held at SOLEIL. The UFXC camera shows very good energy resolution of around 1.5 keV and allows the minimum threshold setting to be as low as 3 keV keeping the high-count-rate capabilities. Measurements of a synchrotron characteristic filling mode prove the proper separation of an isolated bunch of photons and the usability of the detector in time-resolved experiments.