A review and perspective of existing research on the release of nanomaterials from solid nanocomposites

Wet environment-induced adhesion and softening of coenzyme-based polymer elastic patch for treating periodontitis

Periodontitis, a common chronic inflammatory disease caused by pathogenic bacteria, can be treated with diverse biomaterials by loading drugs, cytokines or proteins. However, these biomaterials often show unsatisfactory therapeutic efficiency due to their poor adhesion, short residence time in the wet and dynamic oral cavity and emerging drug resistance. Here we report a wet-responsive methacrylated gelatin (GelMA)-stabilized co-enzyme polymer poly(α-lipoic acid) (PolyLA)-based elastic patch with water-induced adhesion and softening features. In PolyLA-GelMA, the multiple covalent and hydrogen-bonding crosslinking between PolyLA and GelMA prevent PolyLA depolymerization and slow down the dissociation of PolyLA in water, allowing durable adhesion to oral periodontal tissue and continuous release of LA-based bioactive small molecule in periodontitis wound without resorting external drugs. Compared with the undifferentiated adhesion behavior of traditional adhesives, this wet-responsive patch demonstrates a favorable periodontal pocket insertion ability due to its non-adhesion and rigidity in dry environment. In vitro studies reveal that PolyLA-GelMA patch exhibits satisfactory wet tissue adhesion, antibacterial, blood compatibility and ROS scavenging abilities. In the model of rat periodontitis, the PolyLA-GelMA patch inhibits alveolar bone resorption and accelerates the periodontitis healing by regulating the inflammatory microenvironment. This biomacromolecule-stabilized coenzyme polymer patch provides a new option to promote periodontitis treatment.

Characterization of airborne dust emissions from three types of crushed multi-walled carbon nanotube-enhanced concretes

Dispersing Multi-Walled Carbon Nanotubes (MWCNTs) into concrete at low (<1 wt% in cement) concentrations may improve concrete performance and properties and provide enhanced functionalities. When MWCNT-enhanced concrete is fragmented during remodelling or demolition, the stiff, fibrous and carcinogenic MWCNTs will, however, also be part of the respirable particulate matter released in the process. Consequently, systematic aerosolizing of crushed MWCNT-enhanced concretes in a controlled environment and measuring the properties of this aerosol can give valuable insights into the characteristics of the emissions such as concentrations, size range and morphology. These properties impact to which extent the emissions can be inhaled as well as where they are expected to deposit in the lung, which is critical to assess whether these materials might constitute a future health risk for construction and demolition workers. In this work, the impact from MWCNTs on aerosol characteristics was assessed for samples of three concrete types with various amounts of MWCNT, using a novel methodology based on the continuous drop method. MWCNT-enhanced concretes were crushed, aerosolized and the emitted particles were characterized with online and offline techniques. For light-weight porous concrete, the addition of MWCNT significantly reduced the respirable mass fraction (RESP) and particle number concentrations (PNC) across all size ranges (7 nm - 20 μm), indicating that MWCNTs dampened the fragmentation process by possibly reinforcing the microstructure of brittle concrete. For normal concrete, the opposite could be seen, where MWCNTs resulted in drastic increases in RESP and PNC, suggesting that the MWCNTs may be acting as defects in the concrete matrix, thus enhancing the fragmentation process. For the high strength concrete, the fragmentation decreased at the lowest MWCNT concentration, but increased again for the highest MWCNT concentration. All tested concrete types emitted <100 nm particles, regardless of CNT content. SEM imaging displayed CNTs protruding from concrete fragments, but no free fibres were detected.

Everything falls apart: How solids degrade and release nanomaterials, composite fragments, and microplastics

To ensure the safe use of materials, one must assess the identity and quantity of exposure. Solid materials, such as plastics, metals, coatings and cements, degrade to some extent during their life cycle, and releases can occur during manufacturing, use and end-of-life. Releases (e.g., what is released, how does release happen, and how much material is released) depend on the composition and internal (nano)structures of the material as well as the applied stresses during the lifecycle. We consider, in some depth, releases from mechanical, weathering and thermal stresses and specifically address the use cases of fused-filament 3D printing, dermal contact, food contact and textile washing. Solid materials can release embedded nanomaterials, composite fragments, or micro- and nanoplastics, as well as volatile organics, ions and dissolved organics. The identity of the release is often a heterogenous mixture and requires adapted strategies for sampling and analysis, with suitable quality control measures. Control materials enhance robustness by enabling comparative testing, but reference materials are not always available as yet. The quantity of releases is typically described by time-dependent rates that are modulated by the nature and intensity of the applied stress, the chemical identity of the polymer or other solid matrix, and the chemical identity and compatibility of embedded engineered nanomaterials (ENMs) or other additives. Standardization of methods and the documentation of metadata, including all the above descriptors of the tested material, applied stresses, sampling and analytics, are identified as important needs to advance the field and to generate robust, comparable assessments. In this regard, there are strong methodological synergies between the study of all solid materials, including the study of micro- and nanoplastics. From an outlook perspective, we review the hazard of the released entities, and show how this informs risk assessment. We also address the transfer of methods to related issues such as tyre wear, advanced materials and advanced manufacturing, biodegradable polymers, and non-solid matrices. As the consideration of released entities will become more routine in industry via lifecycle assessment in Safe-and-Sustainable-by-Design practices, release assessments will require careful design of the study with quality controls, the use of agreed-on test materials and standardized methods where these exist and the adoption of clearly defined data reporting practices that enable data reuse, meta-analyses, and comparative studies.

In vitro inflammation and toxicity assessment of pre- and post-incinerated organomodified nanoclays to macrophages using high-throughput screening approaches

BACKGROUND

Organomodified nanoclays (ONC), two-dimensional montmorillonite with organic coatings, are increasingly used to improve nanocomposite properties. However, little is known about pulmonary health risks along the nanoclay life cycle even with increased evidence of airborne particulate exposures in occupational environments. Recently, oropharyngeal aspiration exposure to pre- and post-incinerated ONC in mice caused low grade, persistent lung inflammation with a pro-fibrotic signaling response with unknown mode(s) of action. We hypothesized that the organic coating presence and incineration status of nanoclays determine the inflammatory cytokine secretary profile and cytotoxic response of macrophages. To test this hypothesis differentiated human macrophages (THP-1) were acutely exposed (0-20 µg/cm2) to pristine, uncoated nanoclay (CloisNa), an ONC (Clois30B), their incinerated byproducts (I-CloisNa and I-Clois30B), and crystalline silica (CS) followed by cytotoxicity and inflammatory endpoints. Macrophages were co-exposed to lipopolysaccharide (LPS) or LPS-free medium to assess the role of priming the NF-κB pathway in macrophage response to nanoclay treatment. Data were compared to inflammatory responses in male C57Bl/6J mice following 30 and 300 µg/mouse aspiration exposure to the same particles.

RESULTS

In LPS-free media, CloisNa exposure caused mitochondrial depolarization while Clois30B exposure caused reduced macrophage viability, greater cytotoxicity, and significant damage-associated molecular patterns (IL-1α and ATP) release compared to CloisNa and unexposed controls. LPS priming with low CloisNa doses caused elevated cathepsin B/Caspage-1/IL-1β release while higher doses resulted in apoptosis. Clois30B exposure caused dose-dependent THP-1 cell pyroptosis evidenced by Cathepsin B and IL-1β release and Gasdermin D cleavage. Incineration ablated the cytotoxic and inflammatory effects of Clois30B while I-CloisNa still retained some mild inflammatory potential. Comparative analyses suggested that in vitro macrophage cell viability, inflammasome endpoints, and pro-inflammatory cytokine profiles significantly correlated to mouse bronchioalveolar lavage inflammation metrics including inflammatory cell recruitment.

CONCLUSIONS

Presence of organic coating and incineration status influenced inflammatory and cytotoxic responses following exposure to human macrophages. Clois30B, with a quaternary ammonium tallow coating, induced a robust cell membrane damage and pyroptosis effect which was eliminated after incineration. Conversely, incinerated nanoclay exposure primarily caused elevated inflammatory cytokine release from THP-1 cells. Collectively, pre-incinerated nanoclay displayed interaction with macrophage membrane components (molecular initiating event), increased pro-inflammatory mediators, and increased inflammatory cell recruitment (two key events) in the lung fibrosis adverse outcome pathway.

Quantitative evaluation of released nanomaterials from carbon nanotube epoxy nanocomposites during environmental exposure and mechanical treatment

Carbon nanotubes (CNTs) are promising nanomaterials exhibiting high thermal and electrical conductivities, significant stiffness, and high tensile strength. As a result, CNTs have been utilized as additives to enhance properties of various polymeric materials in a broad range of fields. In this study, we investigated the release of CNTs from CNT epoxy nanocomposites exposed to environmental weathering and mechanical stresses. The presence and amount of CNTs released from degraded polymer nanocomposites is important because CNTs can impact physiological systems in humans and environmental organisms. The weathering experiments in this study included nanocomposite exposure to both UV and a water spray, to simulate sunlight and rain exposure, whereas mechanical stresses were induced by shaking and ultrasonication. CNT release from epoxy nanocomposites was quantified by a 14C-labeling method that enabled measurement of the CNT release rates after different weathering and mechanical treatments. In this study, a sample oxidizer was used prior to liquid scintillation counting, because it was shown to reduce interferences from the presence of polymeric materials and achieve a high recovery (95%). Polymer nanocomposite degradation was confirmed by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM), and light microscopy. A continuous release of 14C-labeled nanomaterials was observed after each UV and simulated rain exposure period, with 0.23% (mass/mass) of the total embedded mass of CNTs being released from the CNT nanocomposite during the full weathering process, suggesting that the water spray induced sufficient mechanical stress to eliminate the protective effect of the surface agglomerated CNT network. Importantly, additional mechanical stresses imposed on the weathered nanocomposites by shaking and ultrasonication resulted in further release of approximately 0.27% (mass /mass).

Release and toxicity assessment of carbon nanomaterial reinforced polymers during the use and end-of-life phases: A comparative review

The research on carbon-based nanomaterial (C-NM) composites has increased in the last two decades. This family of functional materials shows outstanding mechanical, thermal and electrical properties, and are being used in a variety of applications. An important challenge remains before C-NM can be fully integrated in our production industries and our lives: to assess the release of debris during production, use, and misuse of composites and the effect they may have on the environment and on human health. During their lifecycle, composites materials can be subjected to a variety of stresses which may release particles from the macroscopic range to the nanoscale. In this review, the release of debris due to abrasion, weathering and combustion as well as their toxicity is evaluated for the three most used C-NM: Carbon Black, Carbon Nanotubes and Graphene-related materials. The goal is to stimulate a Safe-By-Design approach by guiding the selection of carbon nano-fillers for specific applications based of safety and performance.

Fragmentation and release of pristine and functionalized carbon nanotubes from epoxy-nanocomposites during accelerated weathering

There is an increasing volume of nano-enabled materials in the market. Once composites containing nano-additives are disposed of, weathering could deteriorate their structures, releasing nanoparticles and risking exposure of humans and aquatic organisms. Composite degradation due to environmental aging continues, including structural deterioration resulting in cracking, fragmentation, and release of microplastics and nano-additives to the environment. This research aims to study the degradation and release of initially embedded nanomaterials (NMs) from composites and their toxicity. The molecular interaction of carbon nanotube (CNT)/polymer composites is critical for modifying the polymer properties. This study investigated the interactions of functional multiwalled carbon nanotube (MWCNT) composites which affect their release during accelerated weathering processes. Different epoxy-MWCNT composites were prepared by filling a polymer with pure MWCNTs and MWCNTs functionalized with acid (- COOH ) and amine (- NH 2 ) groups. The physical and chemical changes of aged composites were characterized by gravimetric analysis, contact angle measurements, FTIR, SEM, and laser confocal microscopy. A loss of hydrophobicity was observed for composite surfaces long before surface cracks materialized. Released polymer fragments and nanoparticles were analyzed in wash water using TEM, FTIR and Raman spectroscopy. The environmental risks for long-term use of CNT-polymer composites and the influence of fillers on the extent of chemical photodegradation depended on the combination of polymer and fillers. If nanoparticles are released from the matrix, the high surface-to-volume ratio and reactivity of NMs make them highly dynamic in environmental systems. Exposure to these released NMs could negatively affect human health and the environment. This study provides fragmentation and CNT particle release data that could describe how molecular-level interactions between functionalized CNTs and epoxy polymers affect the aging and release of CNTs. A toxicity assessment based on a reactive oxygen species (ROS) formation assay and MTS assay for cell viability and activity of the released polymer and CNT fragments and leachate showed moderate levels of cytotoxicity of released materials as compared to pristine epoxy plates.

New insights into the migration, distribution and accumulation of micro-plastic in marine environment: A critical mechanism review

Microplastics (MPs) are widely distributed in the marine environment, posing a significant threat to marine biota. The contribution of anthropogenic and terrestrial sources to the aquatic ecosystem has led to an increase in MPs findings, and their abundance in aquatic biota has been reported to be of concern. MPs are formed mainly via photo degradation of macroplastics (large plastic debris), and their release into the environment is a result of the degradation of additives. Eco-toxicological risks are increasing for marine organisms, due to the ingestion of MPs, which cause damage to gastrointestinal (GI) tracts and stomach. Plastics with a size <5 mm are considered MPs, and they are commonly identified by Raman spectroscopy, Fourier transfer infrared (FTIR) spectroscopy, and Laser direct infrared (LDIR). The size, density and additives are the main factors influencing the abundance and bioavailability of MPs. The most abundant type of MPs found in fishes are fiber, polystyrenes, and fragments. These microscale pellets cause physiological stress and growth deformities by targeting the GI tracts of fishes and other biota. Approximately 80% MPs come from terrestrial sources, either primary, generated during different products such as skin care products, tires production and the use of MPs as carrier for pharmaceutical products, or secondary plastics, disposed of near coastal areas and water bodies. The issue of MPs and their potential effects on the marine ecosystem require proper attention. Therefore, this study conducted an extensive literature review on assessing MPs levels in fishes, sediments, seawater, their sources, and effects on marine biota (especially on fishes), chemo-physical behavior and the techniques used for their identification.

Towards a surface metric to measure the dustiness of nanomaterial powders

The relevance of dustiness methods is increasingly recognized in the preliminary exposure evaluation of workers handling nanomaterials in powder form, and should also be transposed to the assessment of environmental risk in the future. The methods currently recommended in the European standards are mainly based on determining a mass-based dustiness index [mg kg^-1], whereas surface area is regularly put forward as a more appropriate determinant to assess the pulmonary toxicity of nanoparticles. In this study, we describe an operational methodology leading us to propose a surface metric to determine the dustiness index [m² kg^-1] of nanoparticulate matter. To this end, we demonstrate the equivalence between the external specific surface area of a nanopowder and that of its aerosol with five nanomaterials produced and used on an industrial scale, and covering a range of external specific surface areas from 35 to 230 m² g^-1. Compared to the conventional mass-based dustiness index, the surface-based dustiness index (1) is more discriminating, covering an additional order of magnitude, and (2) has an impact on the powder ranking with potential consequences on the preventive measures to be implemented. Finally, our proposal has the potential to be included in future revisions of European standards for workplace exposure and dustiness measurement, provided that further experimental results on surface-based dustiness indices support these preliminary data.

Adverse effects and underlying mechanism of amorphous silica nanoparticles in liver

Amorphous silica nanoparticles (SiNPs) have been widely used and mass-producted due to its unique properties. With the life cycle of SiNPs-based products, SiNPs are further released into the air, soil, surface water and sediment, resulting in an increasing risk to humans. SiNPs could enter into the human body through vein, respiratory tract, digestive tract or skin. Moreover, recent evidences have showed that, regardless of exposure pathways, SiNPs could even be traced in liver, which is gradually considered as one of the main organs that SiNPs accumulate. Increasing evidences supported the link between SiNPs exposure and adverse liver effects. However, the research models are diverse and the molecular mechanisms have not been well integrated. In this review, the liver-related studies of SiNPs in vivo and in vitro were screened from the PubMed database by systematic retrieval method. We explored the interaction between SiNPs and the liver, and especially proposed a framework of SiNPs-caused liver toxicity, considering AOP Wiki and existing studies. We identified increased reactive oxygen species (ROS) as a molecular initiating event (MIE), oxidative stress, endoplasmic reticulum stress, lysosome disruption and mitochondrial dysfunction as subsequent key events (KEs), which gradually led to adverse outcomes (AOs) containing liver dysfunction and liver fibrosis through a series of key events about cell inflammation and death such as hepatocyte apoptosis/pyroptosis, hepatocyte autophagy dysfuncton and hepatic macrophages pyroptosis. To our best knowledge, this is the first AOP proposed on SiNPs-related liver toxicity. In the future, more epidemiological studies need to be performed and more biomarkers need to be explored to improve the AOP framework for SiNPs-associated liver toxicity.

Nanodelivery of antiretroviral drugs to nervous tissues

Despite the development of effective combined antiretroviral therapy (cART), the neurocognitive impairments associated with human immunodeficiency virus (HIV) remain challenging. The presence of the blood-brain barrier (BBB) and blood-cerebrospinal fluid barrier (BCFB) impedes the adequate penetration of certain antiretroviral drugs into the brain. In addition, reports have shown that some antiretroviral drugs cause neurotoxicity resulting from their interaction with nervous tissues due to long-term systemic exposure. Therefore, the research into the effective therapeutic modality that would cater for the HIV-associated neurocognitive disorders (HAND) and ART toxicity is now receiving broad research attention. Thus, this review explores the latest information in managing HAND using a nanoparticle drug delivery system (NDDS). We discussed the neurotoxicity profile of various approved ART. Also, we explained the applications of silver nanoparticles (AgNPs) in medicine, their different synthesis methods and their interaction with nervous tissues. Lastly, while proposing AgNPs as useful nanoparticles in properly delivering ART to enhance effectiveness and minimize neurocognitive disorders, we hypothesize that the perceived toxicity of AgNPs could be minimized by taking appropriate precautions. One such precaution is using appropriate reducing and stabilizing agents such as trisodium citrate to reduce silver ion Ag + to ground state Ag0 during the synthesis. Also, the usage of medium-sized, spherical-shaped AgNPs is encouraged in AgNPs-based drug delivery to the brain due to their ability to deliver therapeutic agents across BBB. In addition, characterization and functionalization of the synthesized AgNPs are required during the drug delivery approach. Putting all these factors in place would minimize toxicity and enhance the usage of AgNPs in delivering therapeutic agents across the BBB to the targeted brain tissue and could cater for the HIV-associated neurocognitive disorders and neurotoxic effects of antiretroviral drugs (ARDs).

Incineration-Generated Polyethylene Micro-Nanoplastics Increase Triglyceride Lipolysis and Absorption in an In Vitro Small Intestinal Epithelium Model

Despite mounting evidence of micro-nanoplastics (MNPs) in food and drinking water, little is known of the potential health risks of ingested MNPs, and nothing is known of their potential impact on nutrient digestion and absorption. We assessed the effects of environmentally relevant secondary MNPs generated by incineration of polyethylene (PE-I), on digestion and absorption of fat in a high fat food model using a 3-phase in vitro simulated digestion coupled with a tri-culture small intestinal epithelium model. The presence of 400 μg/mL PE-I increased fat digestion by 33% and increased fat absorption by 147 and 145% 1 and 2 h after exposure. Analysis of the PE-I lipid corona during digestion revealed predominantly triacylglycerols with enrichment of fatty acids in the small intestinal phase. Protein corona analysis showed enrichment of triacylglycerol lipase and depletion of β-casein in the small intestinal phase. These findings suggest digestion of triacylglycerol by lipase on the surface of lipid-coated MNPs as a potential mechanism. Further studies are needed to investigate the mechanisms underlying the greater observed increase in fat absorption, to verify these results in an animal model, and to determine the MNP properties governing their effects on lipid digestion and absorption.

Surface Treatment With Hydrophobic Coating Reagents (Organosilanes) Strongly Reduces the Bioactivity of Synthetic Amorphous Silica in vitro

Synthetic amorphous silica (SAS) is industrially relevant material whose bioactivity in vitro is strongly diminished, for example, by protein binding to the particle surface. Here, we investigated the in vitro bioactivity of fourteen SAS (pyrogenic, precipitated, or colloidal), nine of which were surface-treated with organosilanes, using alveolar macrophages as a highly sensitive test system. Dispersion of the hydrophobic SAS required pre-wetting with ethanol and extensive ultrasonic treatment in the presence of 0.05% BSA (Protocol 1). Hydrophilic SAS was suspended by moderate ultrasonic treatment (Protocol 2) and also by Protocol 1. The suspensions were administered to NR8383 alveolar macrophages under serum-free conditions for 16 h, and the release of LDH, GLU, H2O2, and TNFα was measured in cell culture supernatants. While seven surface-treated hydrophobic SAS exhibited virtually no bioactivity, two materials (AEROSIL® R 504 and AEROSIL® R 816) had minimal effects on NR8383 cells. In contrast, non-treated SAS elicited considerable increases in LDH, GLU, and TNFα, while the release of H2O2 was low except for CAB-O-SIL® S17D Fumed Silica. Dispersing hydrophilic SAS with Protocol 1 gradually reduced the bioactivity but did not abolish it. The results show that hydrophobic coating reagents, which bind covalently to the SAS surface, abrogate the bioactivity of SAS even under serum-free in vitro conditions. The results may have implications for the hazard assessment of hydrophobic surface-treated SAS in the lung.

Occupational Safety Analysis for COVID-Instigated Repurposed Manufacturing Lines: Use of Nanomaterials in Injection Moulding

The COVID-19 pandemic instigated massive production of critical medical supplies and personal protective equipment. Injection moulding (IM) is considered the most prominent thermoplastic part manufacturing technique, offering the use of a large variety of feedstocks and rapid production capacity. Within the context of the European Commission-funded imPURE project, the benefits of IM have been exploited in repurposed IM lines to accommodate the use of nanocomposites and introduce the unique properties of nanomaterials. However, these amendments in the manufacturing lines highlighted the need for targeted and thorough occupational risk analysis due to the potential exposure of workers to airborne nanomaterials and fumes, as well as the introduction of additional occupational hazards. In this work, a safety-oriented failure mode and effects analysis (FMEA) was implemented to evaluate the main hazards in repurposed IM lines using acrylonitrile butadiene styrene (ABS) matrix and silver nanoparticles (AgNPs) as additives. Twenty-eight failure modes were identified, with the upper quartile including the seven failure modes presenting the highest risk priority numbers (RPN), signifying a need for immediate control action. Additionally, a nanosafety control-banding tool allowed hazard classification and the identification of control actions required for mitigation of occupation risks due to the released airborne silver nanoparticles.

Nanosafety Analysis of Graphene-Based Polyester Resin Composites on a Life Cycle Perspective

The use, production, and disposal of engineering nanomaterials (ENMs), including graphene-related materials (GRMs), raise concerns and questions about possible adverse effects on human health and the environment, considering the lack of harmonized toxicological data on ENMs and the ability of these materials to be released into the air, soil, or water during common industrial processes and/or accidental events. Within this context, the potential release of graphene particles, their agglomerates, and aggregates (NOAA) as a result of sanding of a battery of graphene-based polyester resin composite samples intended to be used in a building was examined. The analyzed samples were exposed to different weathering conditions to evaluate the influence of the weathering process on the morphology and size distribution of the particles released. Sanding studies were conducted in a tailored designed sanding bench connected to time and size resolving measurement devices. Particle size distributions and particle number concentration were assessed using an optical particle counter (OPC) and a condensation particle counter (CPC), respectively, during the sanding operation. A scanning electron microscope/energy dispersive X-ray (SEM/EDX) analysis was performed to adequately characterize the morphology, size, and chemical composition of the released particles. A toxicity screening study of pristine and graphene-based nanocomposites released using the aquatic macroinvertebrate Daphnia magna and relevant human cell lines was conducted to support risk assessment and decision making. The results show a significant release of nanoscale materials during machining operations, including differences attributed to the % of graphene and weathering conditions. The cell line tests demonstrated a higher effect in the human colon carcinoma cell line Caco2 than in the human fibroblasts (A549 cell line), which means that composites released to the environment could have an impact on human health and biota.

Characteristics of wastewater originating from dental practices using predominantly mercury-free dental materials

Dental materials are currently undergoing a revolution. Mercury use, including traditional amalgam (mercury-containing) material used in dental fillings, is now being widely regulated under the Minamata convention, and dental amalgam is currently being replaced by resin formulations in dentistry. These resin-based materials can be tuned to offer varying material properties by incorporation of a range of nano- and micro-particle based 'fillers' for different dental properties and applications. However, these innovations may have a concomitant effect on the waste streams associated with common dental applications, in particular the potential for higher concentrations of novel micro- and nanomaterials within wastewater streams, and a potential route for novel nanomaterials into the wider Environment. These new materials may also mean that wastewater filtering apparatus commonly deployed at present, such as amalgam separators, may be less efficient or insufficient to capture these new filler materials in dental facility wastewater. In this work, we analyse dental wastewater streams from three dental facilities in Ireland with differing amalgam separators in place. The potential overall toxicity, particulate load and physicochemical properties are analysed. The overall risk posed by these new materials is also discussed.

Graphene oxide incorporating carbon fibre-reinforced composites submitted to simultaneous impact and fire: Physicochemical characterisation and toxicology of the by-products

The toxicological profile of particulates released from carbon fibre-reinforced composites (CFC) incorporating nanoadditives, under impact and fire conditions (e.g. aircraft crash), is unknown to date. Our aim was to investigate the effects of simultaneous impact and fire on the physicochemical features of the particles released from CFCs produced from a graphene oxide (GO)-reinforced epoxy resin and the consequences on its toxicological profile. CFC samples with (CFC + GO) or without GO (CFC) were subjected to simultaneous impact and fire through a specific setup. Soot and residues were characterised and their toxicity was compared to that of virgin GO. Virgin GO was not cytotoxic but induced pro-inflammatory and oxidative stress responses. The toxicity profile of CFC was similar for soot and residue: globally not cytotoxic, inducing a pro-inflammatory response and no oxidative stress. However, an increased cytotoxicity at the highest concentration was potentially caused by fibres of reduced diameters or fibril bundles, which were observed only in this condition. While the presence of GO in CFC did not alter the cytotoxicity profile, it seemed to drive the pro-inflammatory and oxidative stress response in soot. On the contrary, in CFC + GO residue the biological activity was decreased due to the physicochemical alterations of the materials.

Nanowaste: Another Future Waste, Its Sources, Release Mechanism, and Removal Strategies in the Environment

Nanowaste is defined as waste derived from materials with at least one dimension in the 1–100 nm range. The nanomaterials containing products are considered as “nanoproducts” and they can lead to the development of nanomaterial-containing waste, also termed as “nanowaste”. The increased production and consumption of these engineered nanomaterials (ENMs) and nanoproducts that generate enormous amounts of nanowaste have raised serious concerns about their fate, behavior, and ultimate disposal in the environment. It is of the utmost importance that nanowaste is disposed of in an appropriate manner to avoid an adverse impact on human health and the environment. The unique properties of ENMs, combined with an inadequate understanding of appropriate treatment techniques for many forms of nanowaste, makes nanowaste disposal a complex task. Presently, there is a lack of available information on the optimized standards for identifying, monitoring, and managing nanowaste. Therefore, this review highlights concerns about nanowaste as future waste that need to be addressed. The review focuses on ENMs waste (in the form of NP, nanotubes, nanowires, and quantum dots) generated from the manufacture of a wide variety of nanoproducts that end up as nanowaste and adversely affect the environment. Furthermore, the review considers different types of ENMs in waste streams and environmental compartments (i.e., soil, water, and air). Detailed studies are still required to identify data gaps and implement strategies to remove and control this future waste.

Nanoparticle Food Applications and Their Toxicity: Current Trends and Needs in Risk Assessment Strategies

ABSTRACT

Nanotechnology has developed into one of the most groundbreaking scientific fields in the last few decades because it exploits the enhanced reactivity of materials at the atomic scale. The current classification of nanoparticles (NPs) used in foods is outlined in relation to the production and physicochemical characteristics. This review aims to concisely present the most popular and widely used inorganic and organic NPs in food industries. Considering that the toxicity of NPs is often associated with chemical reactivity, a series of in vitro toxicity studies are also summarized, integrating information on the type of NP studies and reported specifications, type of cells used, exposure conditions, and assessed end points. The important role of the digestive system in the absorption and distribution of nanoformulated foods within the body and how this affects the resultant cytotoxicity. Examples of how NPs and their accumulation within different organs are presented in relation to the consumption of specific foods. Finally, the role of developing human health risk assessments to characterize both the potential impact of the hazard and the likelihood or level of human exposure is outlined. Uncertainties exist around risk and exposure assessments of NPs due to limited information on several aspects, including toxicity, behavior, and bioaccumulation. Overall, this review presents current trends and needs for future assessments in toxicity evaluation to ensure the safe application of NPs in the food industry.

HIGHLIGHTS

Nanomaterials, a New Challenge in the Workplace

Nanomaterials are a nanotechnological product of increasing importance given the possibilities they offer to improve quality of life and support sustainable development. Safe management of nanomaterials is needed to ensure that this emerging technology has the highest levels of acceptance among different interest groups, including workers. This chapter reviews the current state that presents the different stages of risk management applied to nanomaterials, including standardisation, regulation, risk assessment and risk control. Particularly, the chapter contextualizes the development of nanotechnologies at European level and analyses the scientific evidence available on the risks derived from nanomaterials use. Furthermore, it highlights the required conditions to encourage the responsible development of nanomaterials, as well as reflects on the lack of consensus in terms of approaches and frameworks that could facilitate standardisation adoption, regulatory enforcement and industry intervention concerning nanomaterials.

Food contact of paper and plastic products containing SiO2, Cu-Phthalocyanine, Fe2O3, CaCO3: Ranking factors that control the similarity of form and rate of release

The paper industry is an important sector annually consuming kilotons of nanoforms and non-nanoforms of fillers and pigments. Fillers accelerate the rate of drying (less energy needed) and product cost (increasing the load of low-cost fillers). The plastic industry is another use sector, where coloristic pigments can be in nanoform, and many food containers are made of plastic. Use of paper to wrap both wet and dry food is consumer practice, but not always intended by producers. Here we compare the release behavior of different nano-enabled products (NEPs) by changing a) nanoform (NF) characteristics, b) NF load, c) the nano-enabled product (NEP) matrix, and d) food simulants. The ranking of these factors enables an assessment of food contact by concepts of analogy, specifically via the similarities of the rate and form of release in food during contact. Three types of matrices were used: Paper, plastic ((Polylactic Acid (PLA), Polyamide (PA6), and Polyurethane (PU)), and a paint formulation. Two nanoforms each of SiO₂, Fe₂O₃, Cu-Phthalocyanine were incorporated, additionally to the conventional form of CaCO₃ that is always contained in paper to reduce cellulose consumption. Tests were guided by the European Regulation EC 1935/2004 and EU 10/2011. No evidence of particle release was observed: the qualitative similarity (the form of release) was high regarding the food contact of all NEPs with embedded NFs. Quantitative similarity of releases depended primarily on the NEP matrix, as this controls the penetration of the simulant fluid into the NEP. The solubility of the NF and impurities in the simulant fluid was the second decisive factor, as dissolution of the NF inside the NEP is the main mechanism of release. This led to complete removal of CaCO₃ in acidic medium, whereas Fe and Si signals remained in the paper, consistent with the low release rates in an ionic form. In our set of 16 NEPs, only one NEP showed a dependence on the REACH NF descriptors (substance, size, shape, surface treatment, crystallinity, impurities), specifically attributed to differences in soluble impurities, whereas for all others the substance of the nanoform was sufficient to predict a similarity of food contact release, without influences of size, shape, surface treatment and crystallinity.

Static modelling of the material flows of micro- and nanoplastic particles caused by the use of vehicle tyres

The emissions of tyre wear particles (TWPs) into the environment are increasing and have negative impacts on the environment and human health. The aim of this study was therefore to establish a mass balance for vehicle tyres und TWP emissions in Austria using static material flow analysis, which enabled a quantification of mass flows of rubber including carbon black as the most mass-relevant tyre filler. Vehicle-specific and mileage-dependent emission factors were used to calculate the TWP emissions. The results for the year 2018 indicate that 80% of the tyre rubber remained in use, while 14% was re-treaded, recycled, incinerated or exported as end-of-life tyres and 6% was emitted as TWPs to air, soil or surface water. Of these 21,200 t/y released and dissipative lost TWPs, 6% were microscale, with a possible size between 0.1 and 10 μm, and 0.3% were nanoscale below 0.1 μm. The mass balance on the substance level shows that the TWPs contained 5,500 t/y of carbon black emitted in the form of airborne TWPs (6%) or entering in the soil or surface waters (47% each). Regarding air pollution from road vehicles, about 3,600 t/y were non-exhaust emissions, including tyre, brake and road-surface wear, which contributed to 9% of total dust emissions across Austria. Scenario analysis for 2050 with regard to e-mobility and the European Green Deal reveals that non-exhaust emissions can only be significantly reduced by a general reduction of the mileage or an environmentally friendly tyre design. This modelling approach provides a solid basis for decision makers in traffic planning as well as for chemical risk assessment. However, dynamic models with higher temporal and spatial resolution are needed to predict future mass flows of TWPs and their environmental fate, including their degradation products and possible accumulation effects.

A critical review of the environmental impacts of manufactured nano-objects on earthworm species

The presence of manufactured nano-objects (MNOs) in various consumer or their (future large-scale) use as nanoagrochemical have increased with the rapid development of nanotechnology and therefore, concerns associated with its possible ecotoxicological effects are also arising. MNOs are releasing along the product life cycle, consequently accumulating in soils and other environmental matrices, and potentially leading to adverse effects on soil biota and their associated processes. Earthworms, of the group of Oligochaetes, are an ecologically significant group of organisms and play an important role in soil remediation, as well as acting as a potential vector for trophic transfer of MNOs through the food chain. This review presents a comprehensive and critical overview of toxic effects of MNOs on earthworms in soil system. We reviewed pathways of MNOs in agriculture soil environment with its expected production, release, and bioaccumulation. Furthermore, we thoroughly examined scientific literature from last ten years and critically evaluated the potential ecotoxicity of 16 different metal oxide or carbon-based MNO types. Various adverse effects on the different earthworm life stages have been reported, including reduction in growth rate, changes in biochemical and molecular markers, reproduction and survival rate. Importantly, this literature review reveals the scarcity of long-term toxicological data needed to actually characterize MNOs risks, as well as an understanding of mechanisms causing toxicity to earthworm species. This review sheds light on this knowledge gap as investigating bio-nano interplay in soil environment improves our major understanding for safer applications of MNOs in the agriculture environment.

Release of carbon nanotubes during combustion of polymer nanocomposites in a pilot-scale facility for waste incineration

Nanocomposites, formed by incorporating nanoparticles into a matrix of standard materials, are increasing on the market. Little focus has been directed towards safe disposal and recycling of these new materials even though the disposal has been identified as a phase of the products' life cycle with a high risk of uncontrolled emissions of nanomaterials. In this study, we investigate if the carbon nanotubes (CNTs), when used as a filler in two types of polymers, are fully destructed in a pilot-scale combustion unit designed to mimic the combustion under waste incineration. The two polymer nanocomposites studied, polycarbonate (PC) with CNT and high-density polyethylene (HDPE) with CNT, were incinerated at two temperatures where the lower temperature just about fulfilled the European waste incineration directive while the upper was chosen to be on the safe side of fulfilling the directive. Particles in the flue gas were sampled and analysed with online and offline instrumentation along with samples of the bottom ash. CNTs could be identified in the flue gas in all experiments, although present to a greater extent when the CNTs were introduced in PC as compared to in HDPE. In the case of using PC as polymer matrix, CNTs were identified in 3-10% of the analysed SEM images while for HDPE in only ~0.5% of the images. In the case of PC, the presence of CNTs decreased with increasing bed temperature (from 10% to 3% of the images). The CNTs identified were always in bundles, often coated with remnants of the polymer, forming particles of ~1-4 μm in diameter. No CNTs were identified in the bottom ash, likely explained by the difference in time when the bottom ash and fly ash are exposed to high temperatures (~hours compared to seconds) in the pilot facility. The results suggest that the residence time of the fly ash in the combustion zone is not long enough to allow full oxidation of the CNTs. Thus, the current regulation on waste incineration (requiring a residence time of the flue gas >850 °C during at least 2 s) may not be enough to obtain complete destruction of CNTs in polymer composites. Since several types of CNTs are known to be toxic, we stress the need for further investigation of the fate and toxicity of CNTs in waste treatment processes.

Form-Specific and Probabilistic Environmental Risk Assessment of 3 Engineered Nanomaterials (Nano-Ag, Nano-TiO2 , and Nano-ZnO) in European Freshwaters

The release of engineered nanomaterials (ENMs) to the environment necessitates an assessment of their environmental risks. The currently available environmental risk assessments (ERA) for ENMs are based on an analysis of the total flows of a specific ENM to the environment and on ecotoxicity studies performed with pristine ENMs. It is known that ENMs undergo transformation during product use and release and in technical systems such as wastewater treatment. The aim of the present study was therefore to perform an ERA of 3 ENMs (nano-Ag, nano-TiO2 , and nano-ZnO) based on a form-specific release model and a form-specific analysis of ecotoxicological data. Predicted environmental concentration values were derived using a form-specific material flow model. Species sensitivity distributions were used to derive predicted-no-effect concentrations (PNECs) for the pristine ENMs and for dissolved and transformed Ag and ZnO. For all ENMs, the matrix-embedded form was included in the assessment. A probabilistic assessment was applied, yielding final probability distributions for the risk characterization ratio (RCR). For nano-Ag, the form-specific assessment resulted in a decrease of the mean RCR from 0.061 for the approach neglecting the different release forms to 0.034 because of the much lower PNEC of transformed Ag. Likewise, for nano-ZnO, the form-specific approach reduced the mean RCR from 1.2 to 0.86. For nano-TiO2 , the form-specific assessment did not change the mean RCR of 0.026. This analysis shows that a form-specific approach can have an influence on the assessment of the environmental risks of ENMs and that, given the availability of form-specific release models, an updated ERA for ENMs can be performed. Environ Toxicol Chem 2021;40:2629-2639. © 2021 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Importance of the number emission factor of combustion-generated aerosols from nano-enabled products

Accidental or open waste burning and incineration of nano-enabled products (NEPs) might lead to the release of incidental aerosols in the nano size range into the environment resulting in harmful effects on humans. We have investigated combustion-generated aerosol release during accidental burning for several real-life NEPs such as paints with silica (SiO₂) and spruce wood panels containing SiO₂ and Fe₂O₃ nanomaterials (NMs), paper with SiO₂ and Fe₂O₃ NMs and polymeric composites with CuPhthtalocyanine NMs in poly lactic acid (PLA), polyamide 6 (PA6) and thermoplastic pol-urethane (TPU) matrices. Chemical compositions, aerosols number emission factors (n_efs) and concentrations of the signature elements of the NMs of the combustion-generated aerosols were investigated. In addition, the residual ash was analyzed. The outcomes of this study shed light on how NM and matrix types influenced the properties of the released aerosols. Based on our results it was established that the combustion-generated aerosols were composed of transformed NMs with modified physical-chemical characteristics compared to the pristine NMs. In addition to aerosols with transformed NMs, there were also particles due to incomplete combustion of the matrix. Types of the pristine NMs and matrices affected the characteristics of the released aerosols. Since the effect of the aerosols is related to the inhaled aerosol number concentration, the n_ef is an important parameter. Our results showed that the n_efs in the size range of 5.6 to 560 nm depended strongly on the type of combusted NEP, which indicated that the NEPs could be categorized according to their potential to release aerosols in this size range when they were burnt. The generated release data facilitate the assessment of human and environmental exposure and the associated risk assessment of combustion-generated aerosols from NEPs.

Selection of an Optimal Abrasion Wheel Type for Nano-Coating Wear Studies under Wet or Dry Abrasion Conditions

Nanocoatings have numerous potential applications in the indoor environment, such as flooring finishes with increased scratch- and wear-resistance. However, given concerns about the potential environmental and human health effects of nanomaterials, it is necessary to develop standardized methods to quantify nanomaterial release during use of these products. One key choice for mechanical wear studies is the abrasion wheel. Potential limitations of different wheels include the release of fragments from the wheel during abrasion, wearing of the wheel from the abrasion process, or not releasing a sufficient number of particles for accurate quantitative analysis. In this study, we evaluated five different wheels, including a typically used silicon oxide-based commercial wheel and four wheels fabricated at the National Institute of Standards and Technology (NIST), for their application in nanocoating abrasion studies. A rapid, nondestructive laser scanning confocal microscopy method was developed and used to identify released particles on the abraded surfaces. NIST fabricated a high performing wheel: a noncorrosive, stainless-steel abrasion wheel containing a deep cross-patch. This wheel worked well under both wet and dry conditions, did not corrode in aqueous media, did not release particles from itself, and yielded higher numbers of released particles. These results can be used to help develop a standardized protocol for surface release of particles from nanoenabled products using a commercial rotary Taber abraser.

Release of graphene-related materials from epoxy-based composites: characterization, quantification and hazard assessment in vitro

Due to their mechanical strength, thermal stability and electrical conductivity, graphene-related materials (GRMs) have been extensively explored for various applications. Moreover, GRMs have been studied and applied as fillers in polymer composite manufacturing to enhance the polymer performance. With the foreseen growth in GRM production, occupational and consumer exposure is inevitable, thus raising concerns for potential health risks. Therefore, this study aims (1) to characterize aerosol particles released after mechanical abrasion on GRM-reinforced epoxy composites, (2) to quantify the amounts of protruding and free-standing GRMs in the abraded particles and (3) to assess the potential effects of the pristine GRMs as well as the abraded particles on human macrophages differentiated from the THP-1 cell line in vitro. GRMs used in this study included graphene nanoplatelets (GNPs), graphene oxide (GO), and reduced graphene oxide (rGO). All types of pristine GRMs tested induced a dose-dependent increase in reactive oxygen species formation, but a decrease in cell viability was only detected for large GNPs at high concentrations (20 and 40 μg mL^-1). The particle modes measured using a scanning mobility particle sizer (SMPS) were 300-400 nm and using an aerodynamic particle sizer (APS) were between 2-3 μm, indicating the release of respirable particles. A significant fraction (51% to 92%) of the GRMs embedded in the epoxy composites was released in the form of free-standing or protruding GRMs in the abraded particles. The abraded particles did not induce any acute cytotoxic effects.

Metal-based engineered nanoparticles in the drinking water treatment systems: A critical review

The emergence of nanotechnologically-enabled materials, compounds or products inevitably leads to engineered nanoparticles (ENPs) released into surface waters. ENPs have already been detected in wastewater streams, drinking water sources and even in tap water at concentrations in the ng/L and μg/L range, making the latter a potential route for humans. The presence of ENPs in raw waters raises concerns over the possibility that ENPs might pose a hazard to the quality and security of drinking water and whether drinking water treatment plants (DWTPs) are prepared to handle this problem. Therefore, it is essential to critically evaluate if ENPs can be effectively removed through water treatment processes to control environmental and human health risks associated with their release. This review includes a summary of the available information on production, presence, potential hazards to human health and environment, and release and behaviour of metal-based ENPs in surface waters and drinking water. In addition, the most extensively studied water treatment processes to remove metal-based ENPs, specifically conventional and advanced processes, are discussed and highlighted in detail. Furthermore, this work identifies the research gaps regarding ENPs removal in DWTPs and discusses future aspects of ENPs in water treatment.

Acute in vivo pulmonary toxicity assessment of occupationally relevant particulate matter from a cellulose nanofiber board

Cellulose nanofibers (CNFs) are an emerging engineered nanomaterial that are utilized in a variety of applications, including as a replacement for urea-formaldehyde, and other adhesives, as the binding agent in manufactured fiber and particle boards. To ensure the health and well-being of those producing, installing, or otherwise using cellulose nanofiber boards (CNFBs) it is imperative that the particulate matter (PM) produced during CNFB manipulation be evaluated for toxicity. We developed and internally verified a generation system to examine the PM produced by sanding CNFB using aluminum oxide sandpaper. With 80-grit sandpaper our system produced a low dispersity aerosol, as determined by a scanning mobility particle sizer and an optical particle counter, with a geometric mean of 28 nm (GSD = 1.60). ICP-MS evaluation showed little difference in metal concentrations between CNFB PM and nonsanded CNFB stock. We then used the system to simultaneously generate and expose both male and female C57BL/6J mice acutely for 4 hours at a concentration of 7.9 mg/m3. Sham-exposed controls were treated similarly but without sanding the CNFB. Analysis of bronchoalveolar lavage (BAL) fluid biomarkers showed no signs of inflammatory response at either 4- or 24-hours post exposure. Further, BAL cell viability, number of total cells, and pulmonary cellular recruitment were not significantly changed between the sham-exposed controls and CNFB-exposed mice. Histology further confirmed no pulmonary toxicity as a result of CNFB PM inhalation. We conclude that inhalation of a high concentration of the PM from manipulation of a CNFB did not produce acute toxic responses within 24 hours of exposure.

The Impacts of Moisture and Ultraviolet Light on the Degradation of Graphene Oxide/Polymer Nanocomposites

The extent to which hydrophilic GO nanofillers regulate polymer degradation during exposure to a combination of ultraviolet (UV) radiation and moisture is presently unknown. Accordingly, this study systematically evaluated the effect of GO on polymer degradability under both humid UV and dry UV conditions. Both GO accumulation at the polymer nanocomposite (PNC) surface and GO release following degradation were also investigated. Different mass loadings of GO were incorporated into waterborne polyurethane (WBPU), a commonly used exterior coating, and the resulting GO/WBPU nanocomposites were exposed to precisely controlled accelerated weathering conditions using the NIST Simulated Photodegradation via High Energy Radiant Exposure (SPHERE) device. Thickness loss and infrared spectroscopy measurements indicated GO slightly improved the durability of WBPU under dry UV conditions but not under humid UV conditions. Raman spectroscopy, scanning electron microscopy, and atomic force microscopy modulus measurements indicated that GO accumulation occurred at and near the PNC surface under both conditions but to a more rapid extent under humid UV conditions. Minimal GO release occurred under dry UV conditions as measured with Raman spectroscopy of aqueous run-off from a simulated rain spray applied to degraded PNCs. In contrast, PNC surface transformations under humid UV conditions suggested that GO release occurred.

Dissolution of Silver Nanoparticles in Colloidal Consumer Products: Effects of Particle Size and Capping Agent

The utilization of silver nanoparticles (AgNPs) in consumer products has significantly increased in recent years, primarily due to their antimicrobial properties. Increased use of AgNPs has raised ecological concerns. Once released into an aquatic environment, AgNPs may undergo oxidative dissolution leading to the generation of toxic Ag+. Therefore, it is critical to investigate the ecotoxicological potential of AgNPs and determine the physicochemical parameters that control their dissolution in aquatic environments. We have investigated the dissolution trends of aqueous colloidal AgNPs in five products, marketed as dietary supplements and surface sanitizers. The dissolution trends of AgNPs in studied products were compared to the dissolution trends of AgNPs in well-characterized laboratory-synthesized nanomaterials: citrate-coated AgNPs, polyvinylpyrrolidone-coated AgNPs, and branched polyethyleneimine-coated AgNPs. The characterization of the studied AgNPs included: particle size, anion content, metal content, silver speciation, and capping agent identification. There were small differences in the dissolved masses of Ag+ between products, but we did not observe any significant differences in the dissolution trends obtained for deionized water and tap water. The decrease of the dissolved mass of Ag+ in tap water could be due to the reaction between Ag+ and Cl-, forming AgCl and affecting their dissolution. We observed a rapid initial Ag+ release and particle size decrease for all AgNP suspensions due to the desorption of Ag+ from the nanoparticles surfaces. The observed differences in dissolution trends between AgNPs in products and laboratory-synthesized AgNPs could be caused by variances in capping agent, particle size, and total AgNP surface area in suspensions.

Interaction of nanoclay-reinforced packaging nanocomposites with food simulants and compost environments

The production of engineered nanomaterials (ENMs) has increased exponentially over the last few decades. ENMs, made from use of engineered nanoparticles (ENPs), have been applied to the food, agriculture, pharmaceutical, and automobile industries. Of particular interest are their applications in packaging nanocomposites for consumer and non-consumer goods. ENPs in nanocomposites are of interest as a packaging material because they reduce the amount of polymer needed, while improving the physical properties. However, the transformation of ENPs in nanocomposite production, their fate, and their toxicity remain unknown while in contact with the package content or after the end of life. The objectives of this chapter are (a) to provide an overview of the main nanoclays used in packaging; (b) to categorize the main polymeric packaging nanocomposites; (c) to provide an overview of the fate and mass transport of ENPs, especially nanoclays; (d) to describe the mass transfer of nanoclays in food simulants and in compost environments; and (e) to identify current and future research needs.

Exposure to airborne nano-titanium dioxide during airless spray painting and sanding

The objectives of the study were to measure and characterize exposure to airborne nanoscale titanium dioxide during airless spraying and sanding of a nano-enabled paint, and to evaluate the effectiveness of dust capture methods in reducing airborne nanoparticle concentrations. A tradesperson performed the work activities in an environmentally controlled chamber. Samples were collected in the tradesperson's breathing zone and in surrounding areas to assess bystander exposure. Filter-based samples were analyzed using gravimetric methods, scanning electron microscopy, and energy dispersive spectroscopy. Differential particle count data were obtained by means of a scanning mobility particle sizer. Local exhaust ventilation provided statistically significant reductions of airborne nanoparticle concentrations during sanding. Sanding the paint after drying with a handheld power sander generated relatively low levels of airborne titanium dioxide. In contrast, task-based exposure measurements collected during the initial airless spray application of the nano-enabled paint suggested a potential for occupational exposures to exceed the time-weighted average exposure limit for ultrafine titanium dioxide recommended by the National Institute for Occupational Safety and Health. Painters applying nano-enabled coatings may have little recourse but to rely, in some instances, on lower tiers of the hierarchy of controls, such as personal protective equipment. In light of these findings, employers and industrial hygienists should characterize exposures and implement the hierarchy of controls to ensure painters are sufficiently protected.

Strategies for robust and accurate experimental approaches to quantify nanomaterial bioaccumulation across a broad range of organisms

One of the key components for environmental risk assessment of engineered nanomaterials (ENMs) is data on bioaccumulation potential. Accurately measuring bioaccumulation can be critical for regulatory decision making regarding material hazard and risk, and for understanding the mechanism of toxicity. This perspective provides expert guidance for performing ENM bioaccumulation measurements across a broad range of test organisms and species. To accomplish this aim, we critically evaluated ENM bioaccumulation within three categories of organisms: single-celled species, multicellular species excluding plants, and multicellular plants. For aqueous exposures of suspended single-celled and small multicellular species, it is critical to perform a robust procedure to separate suspended ENMs and small organisms to avoid overestimating bioaccumulation. For many multicellular organisms, it is essential to differentiate between the ENMs adsorbed to external surfaces or in the digestive tract and the amount absorbed across epithelial tissues. For multicellular plants, key considerations include how exposure route and the role of the rhizosphere may affect the quantitative measurement of uptake, and that the efficiency of washing procedures to remove loosely attached ENMs to the roots is not well understood. Within each organism category, case studies are provided to illustrate key methodological considerations for conducting robust bioaccumulation experiments for different species within each major group. The full scope of ENM bioaccumulation measurements and interpretations are discussed including conducting the organism exposure, separating organisms from the ENMs in the test media after exposure, analytical methods to quantify ENMs in the tissues or cells, and modeling the ENM bioaccumulation results. One key finding to improve bioaccumulation measurements was the critical need for further analytical method development to identify and quantify ENMs in complex matrices. Overall, the discussion, suggestions, and case studies described herein will help improve the robustness of ENM bioaccumulation studies.

Effects of Ultrasonic Dispersion Energy on the Preparation of Amorphous SiO₂ Nanomaterials for In Vitro Toxicity Testing

Synthetic amorphous silica (SAS) constitute a large group of industrial nanomaterials (NM). Based on their different production processes, SAS can be distinguished as precipitated, fumed, gel and colloidal. The biological activity of SAS, e.g., cytotoxicity or inflammatory potential in the lungs is low but has been shown to depend on the particle size, at least for colloidal silica. Therefore, the preparation of suspensions from highly aggregated or agglomerated SAS powder materials is critical. Here we analyzed the influence of ultrasonic dispersion energy on the biologic activity of SAS using NR8383 alveolar macrophage (AM) assay. Fully characterized SAS (7 precipitated, 3 fumed, 3 gel, and 1 colloidal) were dispersed in H₂O by stirring and filtering through a 5 µm filter. Aqueous suspensions were sonicated with low or high ultrasonic dispersion (USD) energy of 18 or 270 kJ/mL, respectively. A dose range of 11.25–90 µg/mL was administered to the AM under protein-free conditions to detect particle-cell interactions without the attenuating effect of proteins that typically occur in vivo. The release of lactate dehydrogenase (LDH), glucuronidase (GLU), and tumor necrosis factor α (TNF) were measured after 16 h. Hydrogen peroxide (H₂O₂) production was assayed after 90 min. The overall pattern of the in vitro response to SAS (12/14) was clearly dose-dependent, except for two SAS which showed very low bioactivity. High USD energy gradually decreased the particle size of precipitated, fumed, and gel SAS whereas the low adverse effect concentrations (LOECs) remained unchanged. Nevertheless, the comparison of dose-response curves revealed slight, but uniform shifts in EC₅₀ values (LDH, and partially GLU) for precipitated SAS (6/7), gel SAS (2/3), and fumed SAS (3/3). Release of TNF changed inconsistently with higher ultrasonic dispersion (USD) energy whereas the induction of H₂O₂ was diminished in all cases. Electron microscopy and energy dispersive X-ray analysis showed an uptake of SAS into endosomes, lysosomes, endoplasmic reticulum, and different types of phagosomes. The possible effects of different uptake routes are discussed. The study shows that the effect of increased USD energy on the in vitro bioactivity of SAS is surprisingly small. As the in vitro response of AM to different SAS is highly uniform, the production process per se is of minor relevance for toxicity.

Considering the forms of released engineered nanomaterials in probabilistic material flow analysis

Most existing models for assessing the releases of engineered nanomaterials (ENMs) into the environment are based on the assumption that ENMs remain in their pristine forms during their whole life cycle. It is known, however, that this is not always the case as ENMs are often embedded into solid matrices during manufacturing and can undergo physical or chemical transformations during their life cycle, e.g. upon release to wastewater. In this work, we present a method for systematically assessing the forms in which nano-Ag and nano-TiO₂ flow through their life cycle (i.e. production, manufacturing, use and disposal) to their points of release to air, soil and surface water. Input data on the forms of released ENMs were probability distributions based on peer-reviewed literature. Release data were incorporated into a probabilistic material flow analysis model to quantify the proportions of ENMs in product-embedded, matrix-embedded, pristine, transformed and dissolved forms in all technical and environmental compartments into which they flow, at the European scale. Releases of nano-Ag to surface water and soil were modelled to occur primarily in transformed forms (Q25 and Q75 of 34-58% and 78-86%, respectively, with means of 53% and 82%), while releases to air were mostly in pristine and matrix-embedded forms (38-46% and 36-44%, respectively, with means of 42% and 40%). In contrast, nano-TiO₂ releases to air, soil and water were estimated to be predominantly in pristine form (75-85%, 90-95%, 96-98%, respectively, with means of 80%, 91% and 97%). The distributions of ENM releases between forms developed here will improve the representativeness and appropriateness of input data for environmental fate modelling and risk assessment of ENMs.

Petroleomic analysis of the treatment of naphthenic organics in oil sands process-affected water with buoyant photocatalysts

The persistence of toxicity associated with the soluble naphthenic organic compounds (NOCs) of oil sands process-affected water (OSPW) implies that a treatment solution may be necessary to enable safe return of this water to the environment. Due to recent advances in high-resolution mass spectrometry (HRMS), the majority of the toxicity of OSPW is currently understood to derive from a subset of toxic classes, comprising only a minority of the total NOCs. Herein, oxidative treatment of OSPW with buoyant photocatalysts was evaluated under a petroleomics paradigm: chemical changes across acid-, base- and neutral-extractable organic fractions were tracked throughout the treatment with both positive and negative ion mode electrospray ionization (ESI) Orbitrap MS. Elimination of detected OS⁺ and NO⁺ classes of concern in the earliest stages of the treatment, along with preferential degradation of high carbon-numbered O₂^- acids, suggest that photocatalysis may detoxify OSPW with higher efficiency than previously thought. Application of petroleomic level analysis offers unprecedented insights into the treatment of petroleum impacted water, allowing reaction trends to be followed across multiple fractions and thousands of compounds simultaneously.

Effects of Sample Preparation on Particle Size Distributions of Different Types of Silica in Suspensions

The granulometric characterization of synthetic amorphous silica (SAS) nanomaterials (NMs) still demands harmonized standard operation procedures. SAS is produced as either precipitated, fumed (pyrogenic), gel and colloidal SAS and these qualities differ, among others, with respect to their state of aggregation and aggregate strength. The reproducible production of suspensions from SAS, e.g., for biological testing purposes, demands a reasonable amount of dispersing energy. Using materials representative for each of the types of SAS, we employed ultrasonic dispersing (USD) at energy densities of 8⁻1440 J/mL and measured resulting particle sizes by dynamic light scattering and laser diffraction. In this energy range, USD had no significant impact on particle size distributions of colloidal and gel SAS, but clearly decreased the particle size of precipitated and fumed SAS. For high energy densities, we observed a considerable contamination of SAS suspensions with metal particles caused by abrasion of the sonotrode&rsquo;s tip. To avoid this problem, the energy density was limited to 270 J/mL and remaining coarse particles were removed with size-selective filtration. The ultrasonic dispersion of SAS at medium levels of energy density is suggested as a reasonable compromise to produce SAS suspensions for toxicological in vitro testing.

Influence of Silica Nanoparticle Density and Flow Conditions on Sedimentation, Cell Uptake, and Cytotoxicity

Careful evaluation of the toxicological response of engineered nanomaterials (ENMs) as a function of physicochemical properties can aid in the design of safe platforms for biomedical applications including drug delivery. Typically, in vitro ENM cytotoxicity assessments are performed under conventional static cell culture conditions. However, such conditions do not take into account the sedimentation rate of ENMs. Herein, we synthesized four types of similar size silica nanoparticles (SNPs) with modified surface roughness, charge, and density and characterized their cytotoxicity under static and dynamic conditions. Influence of particle density on sedimentation and diffusion velocities were studied by comparing solid dense silica nanoparticles of approximately 350 nm in diameter with hollow rattle shape particles of similar size. Surface roughness and charge had negligible impact on sedimentation and diffusion velocities. Lower cellular uptake and toxicity was observed by rattle particles and under dynamic conditions. Dosimetry of ENMs are primarily reported by particle concentration, assuming homogeneous distribution of nanoparticles in cell culture media. However, under static conditions, nanoparticles tend to sediment at a higher rate due to gravitational forces and hence increase effective doses of nanoparticles exposed to cells. By introducing shear flow to SNP suspensions, we reduced sedimentation and nonhomogeneous particle distribution. These results have implications for design of in vitro cytotoxicity assessment of ENMs and suggest that among other factors, sedimentation of nanoparticles in toxicity assessment should be carefully considered.

A review of the fate of engineered nanomaterials in municipal solid waste streams

Significant knowledge and data gaps associated with the fate of product-embedded engineered nanomaterials (ENMs) in waste management processes exist that limit our current ability to develop appropriate end-of-life management strategies. This review paper was developed as part of the activities of the IWWG ENMs in Waste Task Group. The specific objectives of this review paper are to assess the current knowledge associated with the fate of ENMs in commonly used waste management processes, including key processes and mechanisms associated with ENM fate and transport in each waste management process, and to use that information to identify the data gaps and research needs in this area. Literature associated with the fate of ENMs in wastes was reviewed and summarized. Overall, results from this literature review indicate a need for continued research in this area. No work has been conducted to quantify ENMs present in discarded materials and an understanding of ENM release from consumer products under conditions representative of those found in relevant waste management process is needed. Results also indicate that significant knowledge gaps associated with ENM behaviour exist for each waste management process investigated. There is a need for additional research investigating the fate of different types of ENMs at larger concentration ranges with different surface chemistries. Understanding how changes in treatment process operation may influence ENM fate is also needed. A series of specific research questions associated with the fate of ENMs during the management of ENM-containing wastes have been identified and used to direct future research in this area.

Modeling the fate and end-of-life phase of engineered nanomaterials in the Japanese construction sector

To date construction materials that contain engineered nanomaterials (ENMs) are available at the markets, but at the same time very little is known about their environmental fate. Therefore, this study aimed at modeling the potential fate of ENMs by using the example of the Japanese construction sector and by conducting a dynamic material flow analysis. Expert interviews and national reports revealed that about 3920-4660 tons of ENMs are annually used for construction materials in Japan. Nanoscale TiO₂, SiO₂, Al₂O₃ and carbon black have already been applied for decades to wall paints, road markings or concrete. The dynamic material flow model indicates that in 2016 about 95% of ENMs, which have been used since their year of market penetration, remained in buildings, whereas only 5% ended up in the Japanese waste management system or were diffusely released into the environment. Considering the current Japanese waste management system, ENMs were predicted to end up in recycled materials (40-47%) or in landfills (36-41%). It was estimated that only a small proportion was used in agriculture (5-7%, as ENM-containing sewage sludges) or was diffusely released into soils, surface waters or the atmosphere (5-19%). The results indicate that ENM release predominantly depend on their specific applications and characteristics. The model also highlights the importance of adequate collection and treatment of ENM-containing wastes. In future, similar dynamic flow models for other countries should consider, inasmuch as available, historical data on ENM production (e.g. like declaration reports that are annually published by relevant public authorities or associations), as such input data is very important regarding data reliability in order to decrease uncertainties and to continuously improve model accuracy. In addition, more environmental monitoring studies that aim at the quantification of ENM release and inadvertent transfer, particularly triggered by waste treatment processes, would be needed in order to validate such models.

Synthesis of well-defined PCL-b-PnBA-b-PMMA ABC-type triblock copolymers: toward the construction of nanostructures in epoxy thermosets

A novel PCL-b-PnBA-b-PMMA was designed and applied to construct ordered nanostructures within epoxy thermosets.

Comment on "A re-assessment of the safety of silver in household water treatment: rapid systematic review of mammalian in vivo genotoxicity studies"

We wish to thank Fewtrell, Majuru, and Hunter for their article highlighting genotoxic risks associated with the use of particulate silver for primary drinking water treatment. The recent promotion of colloidal silver products for household water treatment in developing countries is problematic due to previously identified concerns regarding manufacturing quality and questionable advertising practices, as well as the low efficiency of silver nanoparticles to treat bacteria, viruses, and protozoa in source waters. However, in the conclusion statement of the manuscript, Fewtrell et al. state, "Before colloidal Ag or AgNP are used in filter matrices for drinking water treatment, consideration needs to be given to how much silver is likely to be released from the matrix during the life of the filter." Unfortunately, it appears Fewtrell et al. were unaware that studies of silver nanoparticle and silver ion elution from ceramic filters manufactured and used in developing countries have already been completed. These existing studies have found that: 1) silver ions, not silver nanoparticles, are eluted from ceramic filters treated with silver nanoparticles or silver nitrate; and, 2) silver ions have not been shown to be genotoxic. Thus, the existing recommendation of applying silver nanoparticles to ceramic filters to prevent biofilm formation within the filter and improve microbiological efficacy should still be adhered to, as there is no identified risk to people who drink water from ceramic filters treated with silver nanoparticles or silver nitrate. We note that efforts should continue to minimize exposure to silver nanoparticles (and silica) to employees in ceramic filter factories in collaboration with the organizations that provide technical assistance to ceramic filter factories.

Considerations for Safe Innovation: The Case of Graphene

The terms "Safe innovation" and "Safe(r)-by-design" are currently popular in the field of nanotechnology. These terms are used to describe approaches that advocate the consideration of safety aspects already at an early stage of the innovation process of (nano)materials and nanoenabled products. Here, we investigate the possibilities of considering safety aspects during various stages of the innovation process of graphene, outlining what information is already available for assessing potential hazard, exposure, and risks. In addition, we recommend further steps to be taken by various stakeholders to promote the safe production and safe use of graphene.