Skin exposure and asthma: is there a connection?

Accurate regulatory classification of chemical respiratory allergens: The case for robust characterisation of causation

Occupational health standards, worker safety and effective regulatory classification relies upon characterisation of occupational asthma and discrimination between allergic asthma, irritant-induced asthma, and work-exacerbated asthma, and the accurate identification of chemical allergens of the respiratory tract. No in silico, in vitro or in vivo experimental method can, either alone or in combination, accurately identify chemical respiratory allergens and provide a sound basis for regulatory classification. Measurement of IgE antibody and skin prick testing can characterise allergy to proteins, but not to chemical respiratory allergens. Therefore, characterisation of causation and accurate regulatory classification of work-related asthma relies upon characterisation of clinical and workplace histories and specific inhalation challenge tests conforming to current guidelines and best practice. This manuscript reviews the important of accurate characterisation of causation in cases of work-related asthma to ensure accurate classification and robust regulation, and to promote a sound basis for clinical and experimental research. Commentaries on selected clinical case studies are provided that highlight key issues that confound attribution of causation. Specific recommendations are made regarding the design, conduct and interpretation of clinical investigations of work-related asthma that could provide a basis of more robust regulatory practice, and the more reliable identification of chemical respiratory allergens.

Comparison of high- and low-molecular-weight sensitizing agents causing occupational asthma: an evidence-based insight

INTRODUCTION

The many substances used at the workplace that can cause sensitizer-induced occupational asthma are conventionally categorized into high-molecular-weight (HMW) agents and low-molecular-weight (LMW) agents, implying implicitly that these two categories of agents are associated with distinct phenotypic profiles and pathophysiological mechanisms.

AREAS COVERED

The authors conducted an evidence-based review of available data in order to identify the similarities and differences between HMW and LMW sensitizing agents.

EXPERT OPINION

Compared with LMW agents, HMW agents are associated with a few distinct clinical features (i.e. concomitant work-related rhinitis, incidence of immediate asthmatic reactions and increase in fractional exhaled nitric oxide upon exposure) and risk factors (i.e. atopy and smoking). However, some LMW agents may exhibit 'HMW-like' phenotypic characteristics, indicating that LMW agents are a heterogeneous group of agents and that pooling them into a single group may be misleading. Regardless of the presence of detectable specific IgE antibodies, both HMW and LMW agents are associated with a mixed Th1/Th2 immune response and a predominantly eosinophilic pattern of airway inflammation. Large-scale multicenter studies are needed that use objective diagnostic criteria and assessment of airway inflammatory biomarkers to identify the pathobiological pathways involved in OA caused by the various non-protein agents.

Fragrances as a trigger of immune responses in different environments

Fragrances can cause allergic skin reactions, expressed as allergic contact dermatitis and reactions in the respiratory tract that range from acute temporary upper airway irritation to obstructive lung disease. These adverse health effects may result from the stimulation of a specific (adaptive) immune response. Th1 cells, which essentially produce interleukin-2 (IL-2) and interferon-γ (IFN-γ), play a key role in allergic contact dermatitis and also on allergic sensitization to common allergens (e.g., nickel and fragrance). It has been shown that fragrance allergy leads to Th2/Th22 production of IL-4, IL-5 and IL-13, controlling the development of IgE and mediating hypersensitivity reactions in the lung, such as asthma. Cytokines released during immune response modulate the expression of cytochrome P450 (CYPs) proteins, which can result in alterations of the pharmacological effects of substances in inflammatory diseases. The mechanisms linking environment and immunity are still not completely understood but it is known that aryl hydrocarbon receptor (AhR) is a sensor with conserved ligand-activated transcription factor, highly expressed in cells that controls complex transcriptional programs which are ligand and cell type specific, with CYPs as targeted genes. This review focuses on these important aspects of immune responses of the skin and respiratory tract cells, describing some in vitro models applied to evaluate the mechanisms involved in fragrance-induced allergy.

Identification of true chemical respiratory allergens: Current status, limitations and recommendations

Asthma in the workplace is an important occupational health issue. It comprises various subtypes: occupational asthma (OA; both allergic asthma and irritant-induced asthma) and work-exacerbated asthma (WEA). Current regulatory paradigms for the management of OA are not fit for purpose. There is therefore an important unmet need, for the purposes of both effective human health protection and appropriate and proportionate regulation, that sub-types of work-related asthma can be accurately identified and classified, and that chemical respiratory allergens that drive allergic asthma can be differentiated according to potency. In this article presently available strategies for the diagnosis and characterisation of asthma in the workplace are described and critically evaluated. These include human health studies, clinical investigations and experimental approaches (structure-activity relationships, assessments of chemical reactivity, experimental animal studies and in vitro methods). Each of these approaches has limitations with respect to providing a clear discrimination between OA and WEA, and between allergen-induced and irritant-induced asthma. Against this background the needs for improved characterisation of work-related asthma, in the context of more appropriate regulation is discussed.

Biobased polyester versus synthetic fiberglass casts for treating stable upper limb fractures in children: a randomized controlled trial

BACKGROUND

Stable upper limb fractures, such as radius, ulna, or distal humerus fractures, are common pediatric orthopedic traumas that are traditionally managed with cast immobilization. The commonly used synthetic fiberglass cast is light and water resistant but may promote skin itchiness during casting, which is a common complaint of patients. In addition, these diisocyanate-based casts have been proven to be toxic and may cause asthma. Herein, we introduce a novel biobased polyester cast to compare its clinical outcomes and patient satisfaction with conventional synthetic fiberglass casts.

METHODS

From Feb 2022 to Nov 2022, we undertook a single-center prospective randomized trial involving 100 children with cast-immobilized stable upper limb fractures. These patients were randomized into either biobased polyester or synthetic fiberglass groups. All patients were regularly followed up till the cast removal which occurred approximately 3-4 weeks after immobilizing. Objective clinical findings and subjective patient questionnaire were all collected and analyzed.

RESULTS

According to the radiographs taken on the day of cast removal, there was no loss of reduction in both groups. The incidence of skin problems was 3.4 times higher in the synthetic fiberglass group than in the biobased polyester group. For the subjective questionnaire, the biobased polyester cast was preferred in every sub-item.

CONCLUSIONS

Our study strongly suggested that the novel biobased polyester cast provides matching stability to conventional fiberglass casts and improves patient satisfaction in an eco-friendlier and safer way.

TRIAL REGISTRATION

ClinicalTrials.gov Protocol Registration and Results System ( https://www.

CLINICALTRIALS

gov/ ; ID: NCT06102603; Date: 26/10/2023).

Reduced Isocyanate Release Using a Waterproof, Resin-Based Cast Alternative Relative to Fiberglass Casts

The effects of occupational isocyanate exposure range from asthma and contact dermatitis to neurotoxicity and cancer. Respiratory sensitization due to orthopedic cast application has been well documented. This study aims to compare the safety of standard-of-care fiberglass casts and a novel waterproof cast alternative by measuring the amount of isocyanate released during off-gassing over time. A 3D-printed arm simulator with comparable casing material amounts was placed in a sealed chamber. An isocyanate-sensing color-changing (SafeAir) tag was used to measure the levels of toxic exposure. Triplicate trials were conducted across all time periods (15 min, 1 h, and 24 h) and conditions. The bare arm simulator and freshly opened tags served as negative controls. Normalized pixel intensity indexes and isocyanate release estimates in ppb were derived from ImageJ-analyzed SafeAir tag photos. Fiberglass casts exhibited greater isocyanate release than both the waterproof alternative (p = 0.0002) and no-cast controls (p = 0.0006), particularly at 24 h. The waterproof alternative and no-cast control did not statistically differ (p = 0.1603). Therefore, the waterproof alternative released less isocyanate than the fiberglass casts. Waterproof cast alternatives may be safer than fiberglass by limiting medical professionals' exposure to toxic isocyanates and, thus, decreasing their risk of suffering occupational asthma.

A Catastrophic Biodiversity Loss in the Environment Is Being Replicated on the Skin Microbiome: Is This a Major Contributor to the Chronic Disease Epidemic?

There has been a catastrophic loss of biodiversity in ecosystems across the world. A similar crisis has been observed in the human gut microbiome, which has been linked to "all human diseases affecting westernized countries". This is of great importance because chronic diseases are the leading cause of death worldwide and make up 90% of America's healthcare costs. Disease development is complex and multifactorial, but there is one part of the body's interlinked ecosystem that is often overlooked in discussions about whole-body health, and that is the skin microbiome. This is despite it being a crucial part of the immune, endocrine, and nervous systems and being continuously exposed to environmental stressors. Here we show that a parallel biodiversity loss of 30-84% has occurred on the skin of people in the developed world compared to our ancestors. Research has shown that dysbiosis of the skin microbiome has been linked to many common skin diseases and, more recently, that it could even play an active role in the development of a growing number of whole-body health problems, such as food allergies, asthma, cardiovascular diseases, and Parkinson's, traditionally thought unrelated to the skin. Damaged skin is now known to induce systemic inflammation, which is involved in many chronic diseases. We highlight that biodiversity loss is not only a common finding in dysbiotic ecosystems but also a type of dysbiosis. As a result, we make the case that biodiversity loss in the skin microbiome is a major contributor to the chronic disease epidemic. The link between biodiversity loss and dysbiosis forms the basis of this paper's focus on the subject. The key to understanding why biodiversity loss creates an unhealthy system could be highlighted by complex physics. We introduce entropy to help understand why biodiversity has been linked with ecosystem health and stability. Meanwhile, we also introduce ecosystems as being governed by "non-linear physics" principles-including chaos theory-which suggests that every individual part of any system is intrinsically linked and implies any disruption to a small part of the system (skin) could have a significant and unknown effect on overall system health (whole-body health). Recognizing the link between ecosystem health and human health allows us to understand how crucial it could be to maintain biodiversity across systems everywhere, from the macro-environment we inhabit right down to our body's microbiome. Further, in-depth research is needed so we can aid in the treatment of chronic diseases and potentially change how we think about our health. With millions of people currently suffering, research to help mitigate the crisis is of vital importance.

Reconstruction of exposure to methylene diphenyl-4,4'-diisocyanate (MDI) aerosol using computational fluid dynamics, physiologically based toxicokinetics and statistical modeling

OBJECTIVES

This study employed computational fluid dynamics (CFD), physiologically based toxicokinetics (PBTK), and statistical modeling to reconstruct exposure to methylene diphenyl-4,4'-diisocyanate (MDI) aerosol. By utilizing a validated CFD model, human respiratory deposition of MDI aerosol in different workload conditions was investigated, while a PBTK model was calibrated using experimental rat data. Biomonitoring data and Markov Chain Monte Carlo (MCMC) simulation were utilized for exposure assessment.

RESULTS

Deposition fraction of MDI in the respiratory tract at the light, moderate, and heavy activity were 0.038, 0.079, and 0.153, respectively. Converged MCMC results as the posterior means and prior values were obtained for several PBTK model parameters. In our study, we calibrated a rat model to investigate the transport, absorption, and elimination of 4,4'-MDI via inhalation exposure. The calibration process successfully captured experimental data in the lungs, liver, blood, and kidneys, allowing for a reasonable representation of MDI distribution within the rat model. Our calibrated model also represents MDI dynamics in the bloodstream, facilitating the assessment of bioavailability. For human exposure, we validated the model for recent and long-term MDI exposure using data from relevant studies.

CONCLUSION

Our computational models provide reasonable insights into MDI exposure, contributing to informed risk assessment and the development of effective exposure reduction strategies.

Immunotoxicity of engineered nanomaterials and their role in asthma

The toxicity of engineered nanomaterials (ENMs) in vivo and in vitro has formed the basis of most studies. However, the toxicity of ENMs, particularly on the immune system, i.e. immunotoxicity, and their role in manipulating it, are less known. This review addresses the initiation or exacerbation as well as the attenuation of allergic asthma by a variety of ENMs and how they may be used in drug delivery to enhance the treatment of asthma. This review also highlights a few research gaps in the study of the immunotoxicity of ENMs, for example, the potential drawbacks of assays used in immunotoxicity assays; the potential role of hormesis during dosing of ENMs; and the variables that result in discrepancies among different studies, such as the physicochemical properties of ENMs, differences in asthmatic animal models, and different routes of administration.

The Identification and Clinical Value Evaluation of CYCS Related to Asthma through Bioinformatics Analysis and Functional Experiments

Background

Asthma is one of the most common respiratory diseases and one of the largest burdens of health care resources across the world. This study is aimed at using bioinformatics methods to find effective clinical indicators for asthma and conducting experimental validation.

Methods

We downloaded GSE64913 data and performed differentially expressed gene (DEG) screening. Weighted gene coexpression network analysis (WGCNA) on DEGs was applied to identify key module most associated with asthma for protein-protein interaction (PPI) analysis. According to the degree value, ten genes were obtained and subjected to expression analysis and receiver operating characteristic (ROC) analysis. Next, key genes were screened for expression analysis and immunological analysis. Finally, cell counting kit-8 (CCK-8) and qRT-PCR were also conducted to observe the influence of hub gene on cell proliferation and inflammatory cytokines.

Results

From the GSE64913 dataset, 711 upregulated and 684 downregulated DEGs were found. In WGCNA, the top 10 genes in the key module were examined by expression analysis in asthma, and CYCS was determined as an asthma-related oncogene with a good predictive ability for the prognosis of asthmatic patients. CYCS is significantly associated with immune cells, such as HHLA2, IDO1, TGFBR1, and CCL18 and promoted the proliferation of asthmatic cells in vitro.

Conclusion

CYCS plays an oncogenic role in the pathophysiology of asthma, indicating that this gene may become a novel diagnostic biomarker and promising target of asthma treatment.

A physiologically-based kinetic (PBK) model for work-related diisocyanate exposure: Relevance for the design and reporting of biomonitoring studies

Diisocyanates are highly reactive substances and known causes of occupational asthma. Exposure occurs mainly in the occupational setting and can be assessed through biomonitoring which accounts for inhalation and dermal exposure and potential effects of protective equipment. However the interpretation of biomonitoring data can be challenging for chemicals with complex kinetic behavior and multiple exposure routes, as is the case for diisocyanates. To better understand the relation between external exposure and urinary concentrations of metabolites of diisocyanates, we developed a physiologically based kinetic (PBK) model for methylene bisphenyl isocyanate (MDI) and toluene di-isocyanate (TDI). The PBK model covers both inhalation and dermal exposure, and can be used to estimate biomarker levels after either single or chronic exposures. Key parameters such as absorption and elimination rates of diisocyanates were based on results from human controlled exposure studies. A global sensitivity analysis was performed on model predictions after assigning distributions reflecting a mixture of parameter uncertainty and population variability. Although model-based predictions of urinary concentrations of the degradation products of MDI and TDI for longer-term exposure scenarios compared relatively well to empirical results for a limited set of biomonitoring studies in the peer-reviewed literature, validation of model predictions was difficult because of the many uncertainties regarding the precise exposure scenarios that were used. Sensitivity analyses indicated that parameters with a relatively large impact on model estimates included the fraction of diisocyanates absorbed and the binding rate of diisocyanates to albumin relative to other macro molecules.We additionally investigated the effects of timing of exposure and intermittent urination, and found that both had a considerable impact on estimated urinary biomarker levels. This suggests that these factors should be taken into account when interpreting biomonitoring data and included in the standard reporting of isocyanate biomonitoring studies.

Occupational Exposure and Health Impact Assessment of Diisocyanates in Finland

Diisocyanates are a group of chemicals widely used in different industrial applications. The critical health effects related to diisocyanate exposure are isocyanate sensitisation, occupational asthma and bronchial hyperresponsiveness (BHR). Industrial air measurements and human biomonitoring (HBM) samples were gathered in specific occupational sectors to examine MDI, TDI, HDI and IPDI and the respective metabolites from Finnish screening studies. HBM data can give a more accurate picture of diisocyanate exposure, especially if workers have been exposed dermally or used respiratory protection. The HBM data were used for conducting a health impact assessment (HIA) in specific Finnish occupational sectors. For this purpose, exposure reconstruction was performed on the basis of HBM measurements of TDI and MDI exposures using a PBPK model, and a correlation equation was made for HDI exposure. Subsequently, the exposure estimates were compared to a previously published dose-response curve for excess BHR risk. The results showed that the mean and median diisocyanate exposure levels and HBM concentrations were low for all diisocyanates. In HIA, the excess risk of BHR from MDI exposure over a working life period was highest in the construction and motor and vehicle industries and repair sectors, resulting in estimated excess risks of BHR of 2.0% and 2.6%, and 113 and 244 extra BHR cases in Finland, respectively. Occupational exposure to diisocyanates must be monitored because a clear threshold for DI sensitisation cannot be established.

Computer-Aided Discovery and Redesign for Respiratory Sensitization: A Tiered Mechanistic Model to Deliver Robust Performance Across a Diverse Chemical Space

Asthma is among the most common occupational diseases with considerable public health and economic costs. Chemicals that induce hypersensitivity in the airways can cause respiratory distress and comorbidities with respiratory infections such as COVID. Robust predictive models for this end point are still elusive due to the lack of an experimental benchmark and the over-reliance of existing in silico tools on structural alerts and structural (vs chemical) similarities. The Computer-Aided Discovery and REdesign (CADRE) platform is a proven strategy for providing robust computational predictions for hazard end points using a tiered hybrid system of expert rules, molecular simulations, and quantum mechanics calculations. The recently developed CADRE model for respiratory sensitization is based on a highly curated data set of structurally diverse chemicals with high-fidelity biological data. The model evaluates absorption kinetics in lung mucosa using Monte Carlo simulations, assigns reactive centers in a molecule and possible biotransformations via expert rules, and determines subsequent reactivity with cell proteins via quantum-mechanics calculations using a multi-tiered regression. The model affords an accuracy above 0.90, with a series of external validations based on literature data in the range of 0.88-0.95. The model is applicable to all low-molecular-weight organics and can inform not only chemical substitution but also chemical redesign to advance development of safer alternatives.

Occupational Asthma Caused by Low-Molecular-Weight Chemicals Associated With Contact Dermatitis: A Retrospective Study

BACKGROUND

Occupational asthma (OA) may have different etiologies, but it is not clear whether the etiologic agents influence the clinical presentation, especially the co-occurrence of skin lesions.

OBJECTIVE

To determine the impact of different asthmagens on the characteristics of OA, with a focus on the occurrence of prior or concomitant skin disorders.

METHODS

In a retrospective analysis of patients who visited the Occupational and Environmental Disease Clinic of a tertiary referral hospital from 2009 to 2019, we classified patients into definite, probable, or possible OA according to prespecified diagnostic guidelines. In multivariate logistic regression with sensitivity analysis, we examined the relation of high- and low-molecular-weight (HMW and LMW) agents with the clinical presentation.

RESULTS

Of 209 cases of OA, 66 were caused by HMW agents and 143 by LMW agents. Patients with OA exposed to LMW agents had higher odds of having (had) allergic contact dermatitis (odds ratio, 5.45 [1.80-23.70]; P < .01), compared with patients exposed to HMW agents. Conversely, HMW agents were associated with higher odds of rhinitis symptoms (odds ratio of LMW/HMW, 0.33 [0.17-0.63]; P < .001) and high total IgE (odds ratio of LMW/HMW, 0.35 [0.17-0.70]; P < .01). Risk factors for having coexisting contact dermatitis included construction work, hairdressing, and exposure to metals or epoxy resins.

CONCLUSIONS

Among patients with OA, exposure to specific LMW agents was associated with a high frequency of contact dermatitis. Different types of asthmagens within HMW or LMW agents appear to determine the phenotype and comorbidity of OA.

Assessment of personal inhalation and skin exposures to polymeric methylene diphenyl diisocyanate during polyurethane fabric coating

Methylene diphenyl diisocyanate (MDI) monomers and polymeric MDI (pMDI) are aromatic isocyanates widely used in the production of polyurethanes. These isocyanates can cause occupational asthma, hypersensitivity pneumonitis, as well as contact dermatitis. Skin exposure likely contributes toward initial sensitization but is challenging to monitor and quantitate. In this work, we characterized workers' personal inhalation and skin exposures to pMDI in a polyurethane fabric coating factory for subsequent health effect studies. Full-shift personal and area air samples were collected from eleven workers in representative job areas daily for 1-2 weeks. Skin exposure to hands was evaluated concomitantly with a newly developed reagent-impregnated cotton glove dosimeter. Samples were analyzed for pMDI by liquid chromatography-tandem mass spectrometry. In personal airborne samples, the concentration of 4,4'-MDI isomer, expressed as total NCO, had a geometric mean (GM) and geometric standard deviation (GSD) of 5.1 and 3.3 ng NCO/m3, respectively (range: 0.5-1862 ng NCO/m3). Other MDI isomers were found at much lower concentrations. Analysis of 4,4'-MDI in the glove dosimeters exhibited much greater exposures (GM: 10 ng/cm2) and substantial variability (GSD: 20 ng NCO/cm2; range: 0-295 ng NCO/cm2). MDI inhalation exposure was well below occupational limits for MDI for all the job areas. However, MDI skin exposure to hands was substantial. These findings demonstrated the potential for substantial isocyanate skin exposure in work settings with very low airborne levels. This exposure characterization should inform future studies that aim to assess the health effects of work exposures to MDI and the effectiveness of protective measures.

Enzymes and sensitization via skin exposure: A critical analysis

Some proteins, including enzymes, can induce allergic sensitization of various types, including allergic sensitization of the respiratory tract. There is now an increased understanding of the role that the skin plays in the development of IgE-mediated allergy and this prompts the question whether topical exposure to enzymes used widely in consumer cleaning products could result in allergic sensitization. Here, the evidence that proteins can interact with the skin immune system and the way they do so is reviewed, together with a consideration of the experience gained over decades of the use of enzymes in laundry and cleaning products. The conclusion drawn is that although transcutaneous sensitization to proteins can occur (typically through compromised skin) resulting in IgE antibody-mediated allergy, in practice such skin contact with enzymes used in laundry and cleaning products does not appear to pose a significant risk of allergic disease. Further, the evidence summarized in this publication support the view that proteins do not pose a risk of allergic contact dermatitis.

Potential classification of chemical immunologic response based on gene expression profiles

Occupational immune diseases are a serious public health burden and are often a result of exposure to low molecular weight (LMW) chemicals. The complete immunological mechanisms driving these responses are not fully understood which has made the classification of chemical allergens difficult. Antimicrobials are a large group of immunologically-diverse LMW agents. In these studies, mice were dermally exposed to representative antimicrobial chemicals (sensitizers: didecyldimethylammonium chloride (DDAC), ortho-phthalaldehyde (OPA), irritants: benzal-konium chloride (BAC), and adjuvant: triclosan (TCS)) and the mRNA expression of cytokines and cellular mediators was evaluated using real-time qPCR in various tissues over a 7-days period. All antimicrobials caused increases in the mRNA expression of the danger signals Tslp (skin), and S100a8 (skin, blood, lung). Expression of the T_H2 cytokine Il4 peaked at different timepoints for the chemicals based on exposure duration. Unique expression profiles were identified for OPA (Il10 in lymph node, Il4 and Il13 in lung) and TCS (Tlr4 in skin). Additionally, all chemicals except OPA induced decreased expression of the cellular adhesion molecule Ecad. Overall, the results from these studies suggest that unique gene expression profiles are implicated following dermal exposure to various antimicrobial agents, warranting the need for additional studies. In order to advance the development of preventative and therapeutic strategies to combat immunological disease, underlying mechanisms of antimicrobial-induced immunomodulation must be fully understood. This understanding will aid in the development of more effective methods to screen for chemical toxicity, and may potentially lead to more effective treatment strategies for those suffering from immune diseases.

Occupational Exposure to Diisocyanates in the European Union

Objectives

Diisocyanates are a chemical group that are widely used at workplaces in many sectors. They are also potent skin- and respiratory sensitizers. Exposure to diisocyanates is a main cause of occupational asthma in the European Union. To reduce occupational exposure to diisocyanates and consequently the cases of diisocyanate-induced asthma, a restriction on diisocyanates was recently adopted under the REACH Regulation in the European Union.

Methods

A comprehensive evaluation of the data on occupational exposure to the most important diisocyanates at workplaces was made and is reported here. The diisocyanates considered are methylene diphenyl diisocyanate (MDI), toluene diisocyanate (TDI), and hexamethylene diisocyanate (HDI), accounting for more than 95% of the market volume in the EU. The exposure assessment is based on data from Chemical Safety Reports (CSRs) of REACH Registration Dossiers, workplace air monitoring data from Germany, from the UK Health and Safety Executive (HSE), and literature data relevant for the EU, and the USA.

Results

Occupational exposure to diisocyanates is particularly relevant in: (i) C.A.S.E. applications (Coatings, Adhesives, Sealants, Elastomers), (ii) production of polyurethanes (PUs) (e.g. slab-stock foam), (iii) handling of partly uncured PU products (e.g. cutting, demoulding, spray application of foam), and (iv) when diisocyanates/PUs are heated (e.g. hot lamination, foundry applications/casting forms). Ranking of the reported data on inhalation to diisocyanate exposure at workplaces (maximum values) leads to following order: (i) HDI and its oligomers in coatings, (ii) MDI in spray foam applications, (iii) TDI in manufacture of foam, (iv) TDI in manufacture of PUs and PU composite materials, (v) TDI in adhesives, (vi) MDI in adhesives, (vii) MDI in manufacture of PUs and PU composite materials, (viii) TDI in coatings, (ix) MDI in manufacture of foam, and (x) HDI in adhesives.

Classification of chemicals as respiratory allergens based on human data: Requirements and practical considerations

Occupational asthma is an important health problem that can include exacerbation of existing asthma, or induce new asthma either through allergic sensitisation, or non-immunological mechanisms. While allergic sensitisation of the respiratory tract can be acquired to proteins, or to low molecular weight chemicals (chemical respiratory allergens) this article is on the latter exclusively. Chemical respiratory allergy resulting in occupational asthma is associated with high levels of morbidity and there is a need, therefore, that chemicals which can cause sensitisation of the respiratory tract are identified accurately. However, there are available no validated, or even widely accepted, predictive test methods (in vivo, in vitro or in silico) that have achieved regulatory acceptance for identifying respiratory sensitising hazards. For this reason there is an important reliance on human data for the identification of chemical respiratory allergens, and for distinguishing these from chemicals that cause occupational asthma through non-immunological mechanisms. In this article the reasons why it is important that care is taken in designating chemicals as respiratory allergens are reviewed. The value and limitations of human data that can aid the accurate identification of chemical respiratory allergens are explored, including exposure conditions, response characteristics in specific inhalation challenge tests, and immunological investigations.

Heterogeneity of Childhood Asthma in Korea: Cluster Analysis of the Korean Childhood Asthma Study Cohort

PURPOSE

Asthma is a heterogeneous airway disease occurring in children, and it has various clinical phenotypes. A clear differentiation of the clinical phenotypes can provide better asthma management and prediction of asthma prognosis. Little is currently known about asthma phenotypes in Korean children. This study was designed to identify asthma phenotypes in school-aged Korean children.

METHODS

This study enrolled 674 children with physician-diagnosed asthma from the Korean childhood Asthma Study (KAS) cohort. The physicians verified the relevant histories of asthma and comorbid diseases, as well as airway lability and hyper-responsiveness from the results of pulmonary function tests and bronchial provocation tests. Questionnaires regarding the participants' baseline characteristics, their environment and self-rating of asthma control were collected at the time of enrollment. Laboratory tests were performed to assess allergy and airway inflammation. Children with asthma were classified by hierarchical cluster analysis.

RESULTS

Of the 674 patients enrolled from the KAS cohort, 447 were included in the cluster analysis. Cluster analysis of these 447 children revealed 4 asthma phenotypes: cluster 1 (n = 216, 48.3%) which was characterized by male-dominant atopic asthma; cluster 2 (n = 79, 17.7%) which was characterized by early-onset atopic asthma with atopic dermatitis; cluster 3 (n = 47, 10.5%) which was characterized by puberty-onset, female-dominant atopic asthma with the low lung function; and cluster 4 (n = 105, 23.5%) which was characterized by early-onset, non-atopic dominant asthma.

CONCLUSIONS

The asthma phenotypes among Korean children can be classified into 4 distinct clusters. Long-term follow-up with these phenotypes will be needed to define their prognosis and response to treatment.

Involvement of Innate Lymphoid Cells and Dendritic Cells in a Mouse Model of Chemical-induced Asthma

PURPOSE

Exposure to low concentrations of toluene diisocyanate (TDI) leads to immune-mediated chemical-induced asthma. The role of the adaptive immune system has already been thoroughly investigated; nevertheless, the involvement of innate immune cells in the pathophysiology of chemical-induced asthma is still unresolved. The aim of the study is to investigate the role of innate lymphoid cells (ILCs) and dendritic cells (DCs) in a mouse model for chemical-induced asthma.

METHODS

On days 1 and 8, BALB/c mice were dermally treated (20 μL/ear) with 0.5% TDI or the vehicle acetone olive oil (AOO; 2:3). On days 15, 17, 19, 22 and 24, the mice received an oropharyngeal challenge with 0.01% TDI or AOO (1:4). One day after the last challenge, airway hyperreactivity (AHR) to methacholine was assessed, followed by an evaluation of pulmonary inflammation and immune-related parameters, including the cytokine pattern in bronchoalveolar lavage fluid, lymphocyte subpopulations of the lymph nodes and their ex vivo cytokine production profile, blood immunoglobulins and DC and ILC subpopulations in the lungs.

RESULTS

Both DC and ILC2 were recruited to the lungs after multiple airway exposures to TDI, regardless of the prior dermal sensitization. However, prior dermal sensitization with TDI alone results in AHR and predominant eosinophilic airway inflammation, accompanied by a typical type 2 helper T (Th2) cytokine profile.

CONCLUSIONS

TDI-induced asthma is mediated by a predominant type 2 immune response, with the involvement of adaptive Th2 cells. However, from our study we suggest that the innate ILC2 cells are important additional players in the development of TDI-induced asthma.

Filaggrin Polymorphisms and the Uptake of Chemicals through the Skin-A Human Experimental Study

BACKGROUND

The filaggrin protein is important for skin barrier structure and function. Loss-of-function (null) mutations in the filaggrin gene FLG may increase dermal absorption of chemicals.

OBJECTIVE

The objective of the study was to clarify if dermal absorption of chemicals differs depending on FLG genotype.

METHOD

We performed a quantitative real-time polymerase chain reaction (qPCR)-based genetic screen for loss-of-function mutations (FLG null) in 432 volunteers from the general population in southern Sweden and identified 28 FLG null carriers. In a dermal exposure experiment, we exposed 23 FLG null and 31 wild-type (wt) carriers to three organic compounds common in the environment: the polycyclic aromatic hydrocarbon pyrene, the pesticide pyrimethanil, and the ultraviolet-light absorber oxybenzone. We then used liquid-chromatography mass-spectrometry to measure the concentrations of these chemicals or their metabolites in the subjects' urine over 48 h following exposure. Furthermore, we used long-range PCR to measure FLG repeat copy number variants (CNV), and we performed population toxicokinetic analysis.

RESULTS

Lag times for the uptake and dermal absorption rate of the chemicals differed significantly between FLG null and wt carriers with low (20-22 repeats) and high FLG CNV (23-24 repeats). We found a dose-dependent effect on chemical absorption with increasing lag times by increasing CNV for both pyrimethanil and pyrene, and decreasing area under the urinary excretion rate curve (AUC(0-40h)) with increasing CNV for pyrimethanil. FLG null carriers excreted 18% and 110% more metabolite (estimated by AUC(0-40h)) for pyrimethanil than wt carriers with low and high CNV, respectively.

CONCLUSION

We conclude that FLG genotype influences the dermal absorption of some common chemicals. Overall, FLG null carriers were the most susceptible, with the shortest lag time and highest rate constants for skin absorption, and higher fractions of the applied dose excreted. Furthermore, our results indicate that low FLG CNV resulted in increased dermal absorption of chemicals. https://doi.org/10.1289/EHP7310.

Chemicals inhaled from spray cleaning and disinfection products and their respiratory effects. A comprehensive review

Spray cleaning and disinfection products have been associated with adverse respiratory effects in professional cleaners and among residents doing domestic cleaning. This review combines information about use of spray products from epidemiological and clinical studies, in vivo and in vitro toxicological studies of cleaning chemicals, as well as human and field exposure studies. The most frequent chemicals in spray cleaning and disinfection products were compiled, based on registrations in the Danish Product Registry. The chemicals were divided into acids, bases, disinfectants, fragrances, organic solvents, propellants, and tensides. In addition, an assessment of selected cleaning and disinfectant chemicals in spray products was carried out. Chemicals of concern regarding respiratory effects (e.g. asthma) are corrosive chemicals such as strong acids and bases (including ammonia and hypochlorite) and quaternary ammonium compounds (QACs). However, the evidence for respiratory effects after inhalation of QACs is ambiguous. Common fragrances are generally not considered to be of concern following inhalation. Solvents including glycols and glycol ethers as well as propellants are generally weak airway irritants and not expected to induce sensitization in the airways. Mixing of certain cleaning products can produce corrosive airborne chemicals. We discuss different hypotheses for the mechanisms behind the development of respiratory effects of inhalation of chemicals in cleaning agents. An integrative assessment is needed to understand how these chemicals can cause the various respiratory effects.

Phthalate exposure and allergic diseases: Review of epidemiological and experimental evidence

Phthalates are among the most ubiquitous environmental contaminants and endocrine-disrupting chemicals. Exposure to phthalates and related health effects have been extensively studied over the past four decades. An association between phthalate exposure and allergic diseases has been suggested, although the literature is far from conclusive. This article reviews and evaluates epidemiological (n = 43), animal (n = 49), and cell culture studies (n = 42), published until the end of 2019, on phthalates and allergic diseases, such as asthma, rhinoconjunctivitis, and eczema. In contrast to earlier reviews, emphasis is placed on experimental studies that use concentrations with relevance for human exposure. Epidemiological studies provide support for associations between phthalate exposures and airway, nasal, ocular, and dermal allergic disease outcomes, although the reported significant associations tend to be weak and demonstrate inconsistencies for any given phthalate. Rodent studies support that phthalates may act as adjuvants at levels likely to be relevant for environmental exposures, inducing respiratory and inflammatory effects in the presence of an allergen. Cell culture studies demonstrate that phthalates may alter the functionality of innate and adaptive immune cells. However, due to limitations of the applied exposure methods and models in experimental studies, including the diversity of phthalates, exposure routes, and allergic diseases considered, the support provided to the epidemiological findings is fragmented. Nevertheless, the current evidence points in the direction of concern. Further research is warranted to identify the most critical windows of exposure, the importance of exposure pathways, interactions with social factors, and the effects of co-exposure to phthalates and other environmental contaminants.

Exposures and urinary biomonitoring of aliphatic isocyanates in construction metal structure coating

BACKGROUND

Isocyanates are highly reactive chemicals used widely in metal structure coating applications in construction. Isocyanates are potent respiratory and skin sensitizers and a leading cause of occupational asthma. At present, there is no cure for isocyanate asthma and no biomarkers of early disease. Exposure reduction is considered the most effective preventive strategy. To date, limited data are available on isocyanate exposures and work practices in construction trades using isocyanates, including metal structure coatings.

OBJECTIVES

The primary objectives of this work were: i) to characterize isocyanate inhalation and dermal exposures among painters during metal structure coating tasks in construction; and ii) to assess the adequacy of existing work practices and exposure controls via urinary biomonitoring pre- and post-shift.

METHODS

Exposures to aliphatic isocyanates based on 1,6-hexamethylene diisocyanate (1,6-HDI) and its higher oligomers (biuret, isocyanurate and uretdione) were measured among 30 workers performing painting of bridges and other metal structures in several construction sites in the Northeastern USA. Exposure assessment included simultaneous measurement of personal inhalation exposures (n = 20), dermal exposures (n = 22) and body burden via urinary biomonitoring pre- and post-shift (n = 53). Contextual information was collected about tasks, processes, materials, work practices, personal protective equipment (PPEs) and exposure controls, work histories, and environmental conditions.

RESULTS

Breathing zone concentrations were the highest for biuret (median, 18.4 μg/m³), followed by 1,6-HDI monomer (median, 3.5 μg/m³), isocyanurate (median, 3.4 μg/m³) and uretdione (median, 1.7 μg/m³). The highest exposures, measured during painting inside an enclosed bridge on a hot summer day, were: 10,288 μg/m³ uretdione; 8,240 μg/m³ biuret; and 947 μg/m³ 1,6-HDI. Twenty percent of samples were above the NIOSH ceiling exposure limit for 1,6- HDI (140 μg/m³) and 35% of samples were above the UK-HSE ceiling for total isocyanate group (70 μg NCO/m³). Isocyanate loading on the gloves was generally high, with a median of 129 μg biuret/pair and maximum of 60.8 mg biuret/pair. The most frequently used PPEs in the workplace were half-face organic vapor cartridge (OVC) respirators, disposable palmar dip-coated polymer gloves, and cotton coveralls. However, 32% of workers didn't wear any respirator, 47% wore standard clothing with short-sleeve shirts and 14% didn't wear any gloves while performing tasks involving isocyanates. Based on biomonitoring results, 58.4% of urine samples exceeded the biological monitoring guidance value (BMGV) of 1 μmol hexamethylene diamine (HDA)/mol creatinine. Post-shift geometric mean HDA normalized to specific gravity increased by 2.5-fold compared to pre-shift (GM, 4.7 vs. 1.9 ng/mL; p value, < 0.001), and only 1.4-fold when normalized to creatinine.

CONCLUSIONS

Exposure and biomonitoring results, coupled with field observations, support the overall conclusions that (i) substantial inhalation and dermal exposures to aliphatic isocyanates occur during industrial coating applications in construction trades; that (ii) the current work practices and exposure controls are not adequately protective. High urinary creatinine values in the majority of workers, coupled with significant cross-shift increases and filed observations, point to the need for further investigations on possible combined effects of heat stress, dehydration, and nutritional deficiencies on kidney toxicity. Implementation of comprehensive exposure control programs and increased awareness are warranted in order to reduce isocyanate exposures and associated health risks among this cohort of construction workers.

How to assess respiratory sensitization of low molecular weight chemicals?

There are no validated and regulatory accepted (animal) models to test for respiratory sensitization of low molecular weight (LMW) chemicals. Since several decades such chemicals are classified as respiratory sensitizers almost exclusively based on observations in workers. However, both respiratory allergens (in which process the immune system is involved) as well as asthmagens (no involvement of the immune system) may induce the same type of respiratory symptoms. Correct classification is very important from a health's perspective point of view. On the other hand, over-classification is not preferable in view of high costs to overdue workplace engineering controls or the chemical ultimately being banned due to Authorities' decisions. It would therefore be very beneficial if respiratory sensitizers can be correctly identified and distinguished from skin sensitizers and non-sensitizers/respiratory irritants. The purpose of this paper is to consider whether LMW chemicals can be correctly identified based on the currently available screening methods in workers, and/or via in silico, in vitro and/or in vivo testing. Collectively, based on the available information further effort is still needed to be able to correctly identify respiratory sensitizers and to distinguish these from skin sensitizers and irritants, not at least because of the far-reaching consequences once a chemical is classified as a respiratory sensitizer.

Skin Exposure Contributes to Chemical-Induced Asthma: What is the Evidence? A Systematic Review of Animal Models

It is generally assumed that allergic asthma originates primarily through sensitization via the respiratory mucosa, but emerging clinical observations and experimental studies indicate that skin exposure to low molecular weight (LMW) agents, i.e. “chemicals,” may lead to systemic sensitization and subsequently develop asthma when the chemical is inhaled. This review aims to evaluate the accumulating experimental evidence that adverse respiratory responses can be elicited upon inhalation of an LMW chemical sensitizer after previous sensitization by dermal exposure. We systematically searched the PubMed and Embase databases up to April 15, 2017, and conducted forward and backward reference tracking. Animal studies involving both skin and airway exposure to LMW agents were included. We extracted 6 indicators of “selective airway hyper-responsiveness” (SAHR)—i.e. respiratory responses that only occurred in previously sensitized animals—and synthesized the evidence level for each indicator into strong, moderate or limited strength. The summarized evidence weight for each chemical agent was graded into high, middle, low or “not possible to assess.” We identified 144 relevant animal studies. These studies involved 29 LMW agents, with 107 (74%) studies investigating the occurrence of SAHR. Indicators of SAHR included physiological, cytological/histological and immunological responses in bronchoalveolar lavage, lung tissue and airway-draining lymph nodes. Evidence for skin exposure-induced SAHR was present for 22 agents; for 7 agents the evidence for SAHR was inconclusive, but could not be excluded. The ability of a chemical to cause sensitization via skin exposure should be regarded as constituting a risk of adverse respiratory reactions.

Ten questions concerning the implications of carpet on indoor chemistry and microbiology

Carpet and rugs currently represent about half of the United States flooring market and offer many benefits as a flooring type. How carpets influence our exposure to both microorganisms and chemicals in indoor environments has important health implications but is not well understood. The goal of this manuscript is to consolidate what is known about how carpet impacts indoor chemistry and microbiology, as well as to identify the important research gaps that remain. After describing the current use of carpet indoors, questions focus on five specific areas: 1) indoor chemistry, 2) indoor microbiology, 3) resuspension and exposure, 4) current practices and future needs, and 5) sustainability. Overall, it is clear that carpet can influence our exposures to particles and volatile compounds in the indoor environment by acting as a direct source, as a reservoir of environmental contaminants, and as a surface supporting chemical and biological transformations. However, the health implications of these processes are not well known, nor how cleaning practices could be optimized to minimize potential negative impacts. Current standards and recommendations focus largely on carpets as a primary source of chemicals and on limiting moisture that would support microbial growth. Future research should consider enhancing knowledge related to the impact of carpet in the indoor environment and how we might improve the design and maintenance of this common material to reduce our exposure to harmful contaminants while retaining the benefits to consumers.

The effect of the inhalation of and topical exposure to zinc oxide nanoparticles on airway inflammation in mice

Zinc oxide nanoparticles (ZnONPs) are widely used in the manufacturing of many commercial products. Workers exposed to ZnO particles may develop metal fume fever. Our previous study suggested that the oropharyngeal aspiration of ZnONPs could cause eosinophilic airway inflammation and increase T helper 2 (Th2) cytokine expression in the absence of allergens in mice. ZnO has been used topically as a sunscreen and a therapeutic agent for dermatological conditions. To understand whether inhalation and topically applied ZnONPs might cause or exert an adjuvant effect on the development of allergic airway inflammation in mice, C57BL/6 J mice were exposed to filtered air or 2.5 mg/m³ ZnONPs via whole-body inhalation for 5 h a day over 5 days, and BALB/c mice were topically exposed to ZnONPs using modified mouse models of atopic dermatitis (AD) and asthma. Ovalbumin (OVA) solution was used as an allergen in the topical exposure experiments. A significantly increased eosinophil count and mixed Th1/Th2 cytokine expression were detected in the bronchoalveolar lavage fluid (BALF) after ZnONP inhalation. However, only mild eosinophilia and low Th2 cytokine expression were detected in the BALF after oropharyngeal OVA aspiration in the high-dose ZnONP topical treatment group. These results suggest that ZnONP inhalation might play a role in the development of allergic airway inflammation in mice. However, topically applied ZnONPs only play a limited role in the development of allergic airway inflammation in mice.

Immunological methods for diagnosis and monitoring of IgE-mediated allergy caused by industrial sensitizing agents (IMExAllergy)

Industrial sensitizing agents (allergens) in living and working environments play an important role in eliciting type 1 allergic disorders including asthma and allergic rhinitis. Successful management of allergic diseases necessitates identifying their specific causes (ie, identify the causative agent(s) and the route of contact to allergen: airborne, or skin contact) to avoid further exposure. Identification of sensitization by a sensitive and validated measurement of specific IgE is an important step in the diagnosis. However, only a limited number of environmental and occupational allergens are available on the market for use in sIgE testing. Accordingly, specific in‐house testing by individual diagnostic and laboratory centers is often required. Currently, different immunological tests are in use at various diagnostic centers that often produce considerably divergent results, mostly due to lack of standardized allergen preparation and standardized procedures as well as inadequate quality control. Our review and meta‐analysis exhibited satisfactory performance of sIgE detection test for most high molecular weight (HMW) allergens with a pooled sensitivity of 0.74 and specificity of 0.71. However, for low molecular weight (LMW) allergens, pooled sensitivity is generally lower (0.28) and specificity higher (0.89) than for HMW tests. Major recommendations based on the presented data include diagnostic use of sIgE to HMW allergens. A negative sIgE result for LMW agents does not exclude sensitization. In addition, the requirements for full transparency of the content of allergen preparations with details on standardization and quality control are underlined. Development of standard operating procedures for in‐house sIgE assays, and clinical validation, centralized quality control and audits are emphasized. There is also a need for specialized laboratories to provide a custom service for the development of tests for the measurement of putative novel occupational allergens that are not commercially available.

Testing of Disposable Protective Garments Against Isocyanate Permeation From Spray Polyurethane Foam Insulation

Background

Diisocyanates (isocyanates), including methylene diphenyl diisocyanate (MDI), are the primary reactive components of spray polyurethane foam (SPF) insulation. They are potent immune sensitizers and a leading cause of occupational asthma. Skin exposure to isocyanates may lead to both irritant and allergic contact dermatitis and possibly contribute to systemic sensitization. More than sufficient evidence exists to justify the use of protective garments to minimize skin contact with aerosolized and raw isocyanate containing materials during SPF applications. Studies evaluating the permeation of protective garments following exposure to SPF insulation do not currently exist.

Objectives

To conduct permeation testing under controlled conditions to assess the effectiveness of common protective gloves and coveralls during SPF applications using realistic SPF product formulations.

Methods

Five common disposable garment materials [disposable latex gloves (0.07 mm thickness), nitrile gloves (0.07 mm), vinyl gloves (0.07 mm), polypropylene coveralls (0.13 mm) and Tyvek coveralls (0.13 mm)] were selected for testing. These materials were cut into small pieces and assembled into a permeation test cell system and coated with a two-part slow-rise spray polyurethane foam insulation. Glass fiber filters (GFF) pretreated with 1-(9-anthracenylmethyl)piperazine) (MAP) were used underneath the garment to collect permeating isocyanates. GFF filters were collected at predetermined test intervals between 0.75 and 20.00 min and subsequently analyzed using liquid chromatography-tandem mass spectrometry. For each garment material, we assessed (i) the cumulative concentration of total isocyanate, including phenyl isocyanate and three MDI isomers, that effectively permeated the material over the test time; (ii) estimated breakthrough detection time, average permeation rate, and standardized breakthrough time; from which (iii) recommendations were developed for the use of similar protective garments following contamination by two-component spray polyurethane foam systems and the limitations of such protective garments were identified.

Results

Each type of protective garment material demonstrated an average permeation rate well below the ASTM method F-739 standardized breakthrough rate threshold of 100.0 ng/cm2 min-1. Disposable latex gloves displayed the greatest total isocyanate permeation rate (4.11 ng/cm2 min-1), followed by the vinyl and nitrile gloves, respectively. The Tyvek coverall demonstrated a greater average rate of isocyanate permeation than the polypropylene coveralls. Typical isocyanate loading was in the range of 900 to 15,000 ng MDI/cm2.

Conclusion

Permeation test data collected during this study indicated that each type of protective garment evaluated, provided a considerable level of protection (i.e. 10-110-fold reduction from the level of direct exposure) against the isocyanate component of the SPF insulation mixture. Nitrile gloves and polypropylene coveralls demonstrated the lowest rate of permeation and the lowest cumulative permeation of total isocyanate for each garment type.

Costs of isocyanate-related occupational diseases: A systematic review

Although isocyanates are increasingly used in manufacturing and workplace exposure to isocyanates is widely recognized as one of the most frequent causes for occupational lung and skin diseases, little is known about the economic burden on the affected individual and the society. This study provides an overview on costs of occupational diseases related to isocyanates. We performed a systematic literature search of studies in the electronic databases of the German Institute of Medical Documentation and Information, and the Canadian Centre for Occupational Health and Safety. We extracted the key characteristics of the studies and performed a study quality assessment. We identified eight studies on the costs of illness, of which five focused on occupational lung diseases and three on occupational skin diseases. Further, eight studies calculated loss of income/compensation payments. Out of the 16 identified articles, only two reported costs directly attributable to isocyanate-induced diseases (asthma). Studies were hardly comparable because they differed substantially in their methodological approaches. Moreover, the quality assessment of the studies revealed substantial limitations. While a wide range of isocyanate-related costs was identified, consequences of isocyanate-related occupational diseases were considerable in terms of societal costs and loss of income. In most studies, indirect costs were the main cost driver. There is a need for high-quality cost of illness studies on isocyanate-induced diseases stratified by degree of severity and sex. Such studies provide valuable information to develop preventive strategies and set priorities for measures to lower the burden of professional health risks.

Assessment and control of exposures to polymeric methylene diphenyl diisocyanate (pMDI) in spray polyurethane foam applicators

In this work we characterize personal inhalation and dermal exposures to diphenyl methane diisocyanate (MDI) and other species in polymeric MDI (pMDI) formulations during spray polyurethane foam (SPF) insulation at 14 sites in New England. We further assess the adequacy of current workplace practices and exposure controls via comparative urinary biomonitoring of the corresponding methylene diphenyl diamine (MDA) pre- and post-shift. MDI and pMDI are potent dermal and respiratory sensitizers and asthmagens, strong irritants of the skin, eyes, and the respiratory tract, and may cause skin burns. This study is the first comprehensive report to-date on the work practices, inhalation and dermal exposures to isocyanates and effectiveness of existing controls during SPF applications. Breathing zone exposures to 4,4' MDI (n = 31; 24 sprayers, 7 helpers) ranged from 0.9 to 123.0 μg/m3 and had a geometric mean (GM) of 13.8 μg/m3 and geometric standard deviation (GSD) of 4.8. Stationary near field area samples (n = 15) were higher than personal exposures: GM, 40.9 (GSD, 3.9) μg/m3, range 1.4-240.8 μg/m3. Sixteen percent of personal air samples and 35% of area samples exceeded the National Institute for Occupational Health and Safety's (NIOSH) full shift recommended exposure limit (REL) of 50 μg/m3, assuming zero exposure for the unsampled time. 4,4' MDI load on the glove dosimeters had a GM of 11.4 (GSD 2.9) μg/glove pair/min, suggesting high potential for dermal exposures. Urinary MDA had a GM of 0.7 (GSD, 3.0) μmol MDA/mol creatinine (range, nd-14.5 μmol MDA/mol creatinine). Twenty-five % of urine samples exceeded the Health and Safety Executive (HSE) biological monitoring guidance value (BMGV) of 1 μmol MDA/mol creatinine. We further report on field observations regarding current exposure controls, discuss implications of these findings and opportunities for improving work practices to prevent isocyanate exposures during SPF insulation.

Novel cutaneous mediators of chemical allergy

Chemical allergy can manifest into allergic contact dermatitis and asthma and the importance of skin sensitization in both of these diseases is increasingly being recognized. Given the unique characteristics of chemical allergy, coupled with the distinct immunological microenvironment of the skin research is still unraveling the mechanisms through which sensitization and elicitation occur. This review first describes the features of chemical sensitization and the known steps that must occur to develop a chemical allergy. Next, the unique immunological properties of the skin - which may influence chemical sensitization - are highlighted. Additionally, mediators involved with the development of allergy are reviewed, starting with early ones - including the properties of haptens, skin integrity, the microbiome, the inflammasome, and toll-like receptors (TLR). Novel cellular mediators of chemical sensitization are highlighted, including innate lymphoid cells, mast cells, T-helper (T_H) cell subsets, and skin intrinsic populations including γδ T-cells and resident memory T-cells. Finally, this review discusses two epigenetic mechanisms that can influence chemical sensitization, microRNAs and DNA methylation. Overall, this review highlights recent research investigating novel mediators of chemical allergy that are present in the skin. It also emphasizes the need to further explore these mediators to gain a better understanding of what makes a chemical an allergen, and how best to prevent the development of chemical-induced allergic diseases.

Skin and respiratory chemical allergy: confluence and divergence in a hybrid adverse outcome pathway

Sensitisation of the respiratory tract to chemicals resulting in respiratory allergy and allergic asthma is an important occupational health problem, and presents toxicologists with no shortage of challenges. A major issue is that there are no validated or, even widely recognised, methods available for the identification and characterisation of chemical respiratory allergens, or for distinguishing respiratory allergens from contact allergens. The first objective here has been review what is known (and what is not known) of the mechanisms through which chemicals induce sensitisation of the respiratory tract, and to use this information to construct a hybrid Adverse Outcome Pathway (AOP) that combines consideration of both skin and respiratory sensitisation. The intention then has been to use the construction of this hybrid AOP to identify areas of commonality/confluence, and areas of departure/divergence, between skin sensitisation and sensitisation of the respiratory tract. The hybrid AOP not only provides a mechanistic understanding of how the processes of skin and respiratory sensitisation differ, buy also a means of identifying areas of uncertainty about chemical respiratory allergy that benefit from a further investment in research.

Risk factors associated with allergic sensitization and asthma phenotypes among poultry farm workers

BACKGROUND

This study investigated the risk factors for occupational allergic sensitization and various asthma phenotypes in poultry-workers.

METHODS

A cross-sectional study of 230 workers used a modified ECRHS questionnaire, spirometry, FeNO, Phadiatop, and sIgE to poultry farming related allergens.

RESULTS

Worker's mean age was 37 ± 9 years, 68% male, 43% current-smokers, 34% atopic, and 5% casual-workers. The prevalence of non-atopic asthma (NAA = 7%) was higher than atopic-asthma (AA = 5%) and probable allergic occupational-asthma (OA = 3%). Sensitization to at least one poultry farming related allergen was 24%. Workers sensitized to chicken-specific-allergens were more likely to be atopic (OR_unadj  = 20.9, 95%CI: 4.7-93.2) or employed as casual-workers (OR_unadj  = 6.0, 95%CI: 1.1-35.9). Work-related chest symptoms were associated the rearing-department (OR_adj  = 3.2, 95%CI: 1.2-8.4) and exposure to high gas/dust/fumes (OR_adj  = 4.8, 95%CI: 2.4-9.5). Airflow reversibility (OR_adj  = 10.9, 95%CI: 2.0-60.3) was significantly associated with casual-work status.

CONCLUSION

Allergic and non-allergic mechanisms play a role in asthma development among poultry-workers with casual workers demonstrating increased risk.

Occupational asthma risk from exposures to toluene diisocyanate: A review and risk assessment

BACKGROUND

Toluene Diisocyanate (TDI) is a known respiratory sensitizer linked to occupational asthma (OA). To better manage worker risks, an appropriate characterization of the TDI-OA dose-risk relationship is needed.

METHODS

The literature was reviewed for data suitable for dose-response modeling. Previous study data were fit to models to derive prospective occupational exposure limits (OELs), using benchmark dose (BMD) and low-dose extrapolation approaches.

RESULTS

Data on eight TDI-exposed populations were suitable for analysis. There were 118 OA cases in a population contributing 13 590 person-years. The BMD-based OEL was 0.4 ppb. The OEL based on low-dose extrapolation to working lifetime extra risk of 1/1000 was 0.3 ppb.

CONCLUSIONS

This study synthesized epidemiologic data to characterize the TDI-OA dose-risk relationship. This approach yielded prospective OEL estimates below recent recommendations by the American Conference of Governmental Industrial Hygienists, but given significant study limitations, this should be interpreted with caution. Confirmatory research is needed.

Sensitizing Capacities and Cross-Reactivity Patterns of Some Diisocyanates and Amines Using the Guinea-Pig Maximization Test. Can p-phenylenediamine be Used as a Marker for Diisocyanate Contact Allergy?

Background:

Isocyanates are mainly considered respiratory allergens but can also cause contact allergy. Diphenylmethane-4,4′-diamine (4,4′-MDA) has been considered a marker for diphenylmethane-4,4′-diisocyanate (4,4′-MDI) contact allergy. Furthermore, overrepresentation of positive patch-test reactions top-phenylenediamine (PPD) in 4,4′-MDA positive patients have been reported.

Objectives:

To investigate the sensitizing capacities of toluene-2,4-diisocyanate (2,4-TDI) and PPD and the cross-reactivity of 4,4′-MDA, 2,4-TDI, dicyclohexylmethane-4,4′-diamine (4,4′-DMDA), dicyclohexylmethane-4,4′-diisocyanate (4,4′-DMDI), 4,4′-MDI and PPD.

Methods:

The Guinea Pig Maximization Test (GPMT) was used.

Results:

PPD was shown to be a strong sensitizer (p<0.001). Animals sensitized to PPD showed cross-reactivity to 4,4′-MDA (p<0.001). Animals sensitized to 4,4′-MDA did not show cross-reactivity to PPD. 8 animals sensitized to 2,4-TDI were sacrificed due to toxic reactions at the induction site and could thus not be fully evaluated.

Conclusion:

PPD was shown to be a strong sensitizer. However, it cannot be used as a marker for isocyanate contact allergy. On the other hand, positive reactions to 4,4′-MDA could indicate a PPD allergy. The intradermal induction concentration of 2,4-TDI (0.70% w/v) can induce strong local toxic reactions in guinea-pigs and should be lowered.

Applicability of an Integrated Testing Strategy consisting of in silico, in chemico and in vitro assays for evaluating the skin sensitization potencies of isocyanates

The skin sensitization potential of chemicals has been traditionally assessed using regulatory accepted in vivo methods, such as guinea pig maximization test or mouse local lymph node assays (LLNAs). A huge effort to reduce and replace the use of animals for safety assessments of chemicals because of regulatory requirements and ethical issues is presently underway, and alternative non-animal methods have been greatly developed. So far, a few studies have investigated the sensitization potencies of isocyanates which is a group of highly reactive chemicals that are known to be occupational allergens. The present study evaluated nine commonly used isocyanates using an in vivo LLNA and assessed the applicability of an Integrated Testing Strategy (ITS) consisting of an in silico Derek Nexus prediction, an in chemico direct peptide reactivity assay (DPRA), and an in vitro human Cell Line Activation Test (h-CLAT) to isocyanates. All nine isocyanates were evaluated as positive using the LLNA, Derek Nexus and DPRA, whereas seven chemicals tested positive using the h-CLAT: hexamethylene diisocyanate tested negative, and 1,5-diisocyanatonaphthalene could not be examined because of a solubility issue. When assessed using the ITS, the positive/negative evaluations of skin sensitization hazard were consistent with those assessed using the LLNA for all nine chemicals. However, the potency prediction results of the ITS tended to be underestimated, compared with those of the LLNA. The data presented in this work provide insights into the performance of non-animal testing approaches for evaluating the skin sensitization potencies of isocyanates.

Occupational contact urticaria and protein contact dermatitis: causes and concomitant airway diseases

BACKGROUND

Contact urticaria (CU) and protein contact dermatitis (PCD) are mainly induced by an immediate, IgE-mediated immunological mechanism. Immediate sensitization is also linked to asthma and/or allergic rhinitis.

OBJECTIVES

To report causes of work-induced CU and PCD, and to evaluate the occurrence of concomitant airway diseases.

METHODS

We retrospectively reviewed the patient files of cases diagnosed with CU or PCD at the Finnish Institute of Occupational Health during 1995-2011. We obtained data on occupation, exposures, clinical and immunological test results, and diagnosed occupational skin and respiratory diseases.

RESULTS

Altogether, 291 cases of occupational CU or PCD were diagnosed during the study period. The most common causes were flour, cow dander, natural rubber latex and acid anhydrides. Concomitant occupational asthma caused by the same agent as the skin disease was detected in 60 patients (21%), and occupational rhinitis was detected in 111 patients (38%).

CONCLUSIONS

Almost half of the patients (46%) with occupational CU and PCD had concomitant occupational airway disease. Patients with CU/PCD should always be asked about respiratory symptoms, and preventive measures at the workplace should include protection of both the skin and the airways.

Sensitization and cross-reactivity patterns of contact allergy to diisocyanates and corresponding amines: investigation of diphenylmethane-4,4'-diisocyanate, diphenylmethane-4,4'-diamine, dicyclohexylmethane-4,4'-diisocyanate, and dicylohexylmethane-4,4'-diamine

Background

Isocyanates are used in polyurethane production. Dermal exposure to isocyanates can induce contact allergy. The most common isocyanate is diphenylmethane diisocyanate used for industrial purposes. The isomer diphenylmethane‐4,4′‐diisocyanate (4,4′‐MDI) is used in patch testing. Diphenylmethane‐4,4′‐diamine (4,4′‐MDA) is its corresponding amine. Concurrent reactions to 4,4′‐MDI and 4,4′‐MDA have been reported, as have concurrent reactions to 4,4′‐MDI and dicyclohexylmethane‐4,4′‐diisocyanate (4,4′‐DMDI).

Objectives

To investigate the sensitization capacities and the cross‐reactivity of 4,4′‐MDI, 4,4′‐MDA, 4,4′‐DMDI, and dicyclohexylmethane‐4,4′‐diamine (4,4′‐DMDA).

Methods

The guinea‐pig maximization test (GPMT) was used.

Results

The GPMT showed sensitizing capacities for all investigated substances: 4,4′‐MDI, 4,4′‐MDA, 4,4′‐DMDI, and 4,4′‐DMDA (all p < 0.001). 4,4′‐MDI‐sensitized animals showed cross‐reactivity to 4,4′‐MDA (p < 0.001) and 4,4′‐DMDI (all p < 0.05). 4,4′‐MDA‐sensitized animals showed cross‐reactivity to 4,4′‐DMDA (p = 0.008).

Conclusion

All of the investigated substances were shown to be strong sensitizers. Animals sensitized to 4,4′‐MDI showed cross‐reactivity to 4,4′‐MDA and 4,4′‐DMDI, supporting previous findings in the literature. The aromatic amine 4,4′‐MDA showed cross‐reactivity to the aliphatic amine 4,4′‐DMDA.

Effects by inhalation of abundant fragrances in indoor air - An overview

Odorous compounds (odors) like fragrances may cause adverse health effects. To assess their importance by inhalation, we have reviewed how the four major abundant and common airborne fragrances (α-pinene (APN), limonene (LIM), linalool (LIL), and eugenol (EUG)) impact the perceived indoor air quality as odor annoyance, sensory irritation and sensitization in the airways. Breathing and cardiovascular effects, and work performance, and the impact in the airways of ozone-initiated gas- and particle phase reactions products have also been assessed. Measured maximum indoor concentrations for APN, LIM and LIL are close to or above their odor thresholds, but far below their thresholds for sensory irritation in the eyes and upper airways; no information could be traced for EUG. Likewise, reported risk values for long-term effects are far above reported indoor concentrations. Human exposure studies with mixtures of APN and LIM and supported by animal inhalation models do not support sensitization of the airways at indoor levels by inhalation that include other selected fragrances. Human exposure studies, in general, indicate that reported lung function effects are likely due to the perception rather than toxic effects of the fragrances. In general, effects on the breathing rate and mood by exposure to the fragrances are inconclusive. The fragrances may increase the high-frequency heart rate variability, but aerosol exposure during cleaning activities may result in a reduction. Distractive effects influencing the work performance by fragrance/odor exposure are consistently reported, but their persistence over time is unknown. Mice inhalation studies indicate that LIM or its reaction mixture may possess anti-inflammatory properties. There is insufficient information that ozone-initiated reactions with APN or LIM at typical indoor levels cause airway effects in humans. Limited experimental information is available on long-term effects of ozone-initiated reaction products of APN and LIM at typical indoor levels.

Isocyanate Exposure Below Analytical Detection When a Paint Brush and Roller Are Used to Apply Moisture-Cure Polyurethane Paint

Isocyanate exposure is known to be hazardous when polyurethane paints are applied with a spray gun, but less is known of exposure when paint is applied with a paint brush and roller. Concentrations of 1,6-hexamethylene diisocyanate (HDI) monomer and three HDI polymers were assessed when two moisture-cure polyurethane paints containing 31-35% isocyanates were applied with a paint roller and brush. Short-term 15-min samples were taken during paint application in an indoor test environment with no ventilation (n= 12); in an outdoor test environment (n= 11); and in an outdoor in-situ assessment (n= 22). The outdoor in-situ assessment involved the painting of a bus shelter and light poles at a public transit station over two night shifts. All isocyanate samples were below analytical detection. The analytical limits of detection for HDI monomer, HDI biuret, HDI isocyanurate, and HDI uretdione were 0.005, 0.84, 0.87, and 0.88 µg, respectively. The finding that isocyanate concentrations were below detection is attributed to the use of paint roller and brush which minimize paint aerosolization and the paint formulation itself which contained <1% of volatile HDI monomer.

Anti-hapten antibodies in response to skin sensitization

Whereas T lymphocyte (T cell) activation is the key event in the acquisition of skin sensitization and subsequent elicitation of allergic contact dermatitis, the humoral component of immune responses to organic contact allergens has received little consideration. There is evidence that, in experimental animals, topical exposure to potent contact allergens is associated with B cell activation and proliferation, and hapten-specific antibody production. However, there is very limited evidence available for anti-hapten antibody responses being induced following topical exposure of humans to contact allergens. Nevertheless, it is important to appreciate that there are almost no negative studies in which evidence for antibody production as the result of skin sensitization has been sought and not found. That is, there is absence of evidence rather than evidence of absence. Furthermore, exposure to chemical respiratory allergens, in which the skin has been implicated as a potential route of sensitization, results in anti-hapten antibody responses. It is proposed that skin sensitization to contact allergens will normally be accompanied by antibody production. The phenomenon is worthy of investigation, as anti-hapten antibodies could potentially influence and/or regulate the induction of skin sensitization. Moreover, such antibodies may provide an informative correlate of the extent to which sensitization has been acquired.

Isocyanates and work-related asthma: Findings from California, Massachusetts, Michigan, and New Jersey, 1993-2008

BACKGROUND

Isocyanates remain a leading cause of work-related asthma (WRA).

METHODS

Two independent data systems were analyzed for the period 1993-2008: (1) State-based WRA case surveillance data on persons with isocyanate-induced WRA from four states, and (2) Occupational Safety and Health Administration (OSHA) Integrated Management Information System (IMIS) isocyanate air sampling results.

RESULTS

We identified 368 cases of isocyanate-induced WRA from 32 industries and 678 OSHA isocyanate air samples with detectable levels from 31 industries. Seventeen industries were unique to one or the other dataset.

CONCLUSION

Isocyanate-induced WRA continues to occur in a wide variety of industries. Two data systems uncovered industries with isocyanate exposures and/or illness. Improved control measures and standards, including medical surveillance, are needed. More emphasis is needed on task-specific guidance, spill clean-up procedures, skin and respiratory protection, and targeted medical monitoring to mitigate the hazards of isocyanate use.