A Novel Compact Broadband Quasi-Twisted Branch Line Coupler Based on a Double-Layered Microstrip Line

A novel quasi-twisted miniaturized wideband branch line coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The input and output terminals, each with a length of λg/4, and the pair of quarter-wavelength horizontal parallel arms are converted into a Z-shaped meandered microstrip line in the designed structure. Conversely, the pair of quarter-wavelength vertical arms are halved into two lines and transformed into a periodically loaded slow-wave structure. The bisected parts of the BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4 × 18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10 × 23 mm2 at 6 GHz. Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, S33, S21, and the phase difference between outputs (∠S21 - ∠S41). However, if a coupling parameter (S41) of up to -7.5 dB is considered, then the relative bandwidth reduces to 53.9% (4.6-10 GHz) for port 1 as the input. Similarly, for port 3 as the input, the obtained bandwidth is 75.8% (4.5-10 GHz) for S33, S11, S43, and the phase difference between outputs (∠S43 - ∠S23). Likewise, this bandwidth reduces to 56% (4.5-8 GHz) when a coupling parameter (S23) of up to -7.5 dB is considered. In contrast, the relative bandwidth for the ordinary BLC is 41% at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3 and a loss tangent of 0.025. An isolation of -13 dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1 dB to -3.5 dB at a frequency of 6 GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5° and 94.8° at a frequency of 6 GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler matrix (BM) for sub-6 GHz 5G beamforming networks.

A Wideband True Time Delay Circuit Using 0.25 µm GaN HEMT Technology

This paper presents a wideband 4-bit true time delay IC using a 0.25 μm GaN HEMT (High-Electron-Mobility Transistor) process for the beam-squint-free phased array antennas. The true time delay IC is implemented with a switched path circuit topology using DPDT (Double Pole Double Throw) with no shunt transistor in the inter-stages to improve the bandwidth and SPDT (Single Pole Single Throw) switches at the input and the output ports. The delay lines are implemented with CLC π-networks with the lumped element to ensure a compact chip size. A negative voltage generator and an SPI controller are implemented in the PCB (Printed Circuit Board) due to the lack of digital control logic in GaN technology. A maximum time delay of ~182 ps with a time delay resolution of 10.5 ps is achieved at DC-6 GHz. The RMS (Root Mean Square) time delay and amplitude error are <5 ps and <0.6 dB, respectively. The measured insertion loss is <6.8 dB and the input and output return losses are >10 dB at DC-6 GHz. The current consumption is nearly zero with a 3.3 V supply. The chip size including pads is 2.45 × 1.75 mm2. To the authors' knowledge, this is the first demonstration of a true time delay IC using GaN HEMT technology.

Wideband Array Signal Processing with Real-Time Adaptive Interference Mitigation

Wideband beamforming and interference cancellation for phased array antennas requires advances in signal processing algorithms, software, and specialized hardware platforms. A high-throughput array receiver has been developed that enables communication in radio frequency interference-rich environments with field programmable gate array (FPGA)-based frequency channelization and packetization. In this study, a real-time interference mitigation algorithm was implemented on graphics processing units (GPUs) contained in the data pipeline. The key contribution is a hardware and software pipeline for subchannelized wideband array signal processing with 150 MHz instantaneous bandwidth and interference cancellation with a heterogeneous, distributed, and scaleable digital signal processing (DSP) architecture that achieves 30 dB interferer cancellation null depth in real time with a moving interference source.

A Multimode 28 GHz CMOS Fully Differential Beamforming IC for Phased Array Transceivers

A 28 GHz fully differential eight-channel beamforming IC (BFIC) with multimode operations is implemented in 65 nm CMOS technology for use in phased array transceivers. The BFIC has an adjustable gain and phase control on each channel to achieve fine beam steering and beam pattern. The BFIC has eight differential beamforming channels each consisting of the two-stage bi-directional amplifier with a precise gain control circuit, a six-bit phase shifter, a three-bit digital step attenuator, and a tuning bit for amplitude and phase variation compensation. The Tx and Rx mode overall gains of the differential eight-channel BFIC are around 11 dB and 9 dB, respectively, at 27.0-29.5 GHz. The return losses of the Tx mode and Rx mode are >10 dB at 27.0-29.5 GHz. The maximum phase of 354° with a phase resolution of 5.6° and the maximum attenuation of 31 dB, including the gain control bits with an attenuation resolution of 1 dB, is achieved at 27.0-29.5 GHz. The root mean square (RMS) phase and amplitude errors are <3.2° and <0.6 dB at 27.0-29.5 GHz, respectively. The chip size is 3.0 × 3.5 mm², including pads, and Tx mode current consumption is 580 mA at 2.5 V supply voltage.

A Tuned Microwave Resonant System for Subcutaneous Imaging

A compact and planar imaging system was developed using a flexible polymer substrate that can distinguish subcutaneous tissue abnormalities, such as breast tumors, based on electromagnetic-wave interactions in materials where permittivity variations affect wave reflection. The sensing element is a tuned loop resonator operating in the industrial, scientific, and medical (ISM) band at 2.423 GHz, providing a localized high-intensity electric field that penetrates into tissues with sufficient spatial and spectral resolutions. The resonant frequency shifts and magnitudes of the reflection coefficients indicate the boundaries of abnormal tissues under the skin due to their high contrasts to normal tissues. The sensor was tuned to the desired resonant frequency with a reflection coefficient of -68.8 dB for a radius of 5.7 mm, with a tuning pad. Quality factors of 173.1 and 34.4 were achieved in simulations and measurements in phantoms. An image-processing method was introduced to fuse raster-scanned 9 × 9 images of resonant frequencies and reflection coefficients for image-contrast enhancement. The results showed a clear indication of the tumor's location at a depth of 15 mm and the capability to identify two tumors both at the depth of 10 mm. The sensing element can be expanded to a four-element phased array for deeper field penetration. Field analysis showed the depths of -20 dB attenuation were improved from 19 to 42 mm, giving wider coverage in tissues at resonance. Results showed that a quality factor of 152.5 was achieved and a tumor could be identified at a depth of up to 50 mm. In this work, simulations and measurements were conducted to validate the concept, showing great potential for subcutaneous imaging in medical applications in a noninvasive, efficient, and lower-cost way.

Compact Eight-Element MIMO Antenna with Reduced Mutual Coupling and Beam-Scanning Performance

In this study, a multiple-input multiple-output (MIMO) antenna for wide scanning is designed. By adding slits to the patches, each element is intended to strengthen the isolation between the radiating elements. The proposed high isolation and wide scanning antenna combine to achieve the desired phased-array antenna. The array has a main beam pointing to the desired scanning region and a minimum side lobe level (SLL) in the undesired direction. A compact and linear eight-element array with an interelement spacing of λ/2 is designed and analyzed for beam scanning in the E-plane. Considering the worst case, the proposed array has a very low mutual coupling of (S21 = -24 dB), and it realizes a gain of 9.3 dBi and an SLL of 11 dB at a scanning angle of 70∘. The antenna performance was studied in terms of the S-parameter, radiation patterns, beam-scanning performance, envelope correlation coefficient (ECC), diversity gain (DG), peak gain, and efficiency. A close agreement was observed between the simulated and measured results.

Thermal Deformation Modeling for Phased Array Antenna Compensation Control

Thermal compensation control can correct errors caused by the thermal deformation of phased array antenna (PAA) panels. Thermal deformation of the panel is needed to calculate the compensation value. While the PAA is working, thermal deformation is unconditional to measure, but predicting it by temperature is feasible. However, thermal deformation is also affected by other factors, such as the structural shape, assembly method, and material parameters, and it is difficult to measure these parameters of PAA because of the complex structure. In contrast, the measurement method of the temperature and thermal deformation of the PAA in the laboratory is much easier. Therefore, a comprehensive influence parameters (CIPs)-finite element method (FEM) method was proposed in this study, it can extract the influence of above parameters on thermal deformation from temperature and thermal deformation measurement data and build a thermal deformation prediction model. Experiments have verified that the CIPs-FEM can greatly reduce the difficulty of thermal deformation modeling and have a high prediction accuracy.

Rapid Test Method for Multi-Beam Profile of Phased Array Antennas

The measurement of the phased array antenna (PAA) is completely different from the traditional antenna, due to its multi beam patterns. Usually, each beam pattern of the PAA needs a separate measurement, which makes the overall time extremely long. Thus, the traditional method can no longer meet the efficiency and cost requirements of new PAA measurement. In this paper, a pattern reconstruction method is proposed which significantly reduce the measurement time of multi-beam PAAs. With the known array element patterns (AEP) and theoretical weighted port excitation of the beams, any beam pattern can be predicted by measuring only a certain beam pattern, due to the element excitation coefficient (including the matching, mutual coupling, and manufacturing factors, etc.) of the specific PAA being calculated. The approach has low reconstruction error in term of beam pointing accuracy, side lobe, and co-polar and cross-polar patterns while being validated for large scanning range. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna can be improved by 10 times or even more.

Inkjet-Printed Graphene-Based 1 × 2 Phased Array Antenna

Low-cost and conformal phased array antennas (PAAs) on flexible substrates are of particular interest in many applications. The major deterrents to developing flexible PAA systems are the difficulty in integrating antenna and electronics circuits on the flexible surface, as well as the bendability and oxidation rate of radiating elements and electronics circuits. In this research, graphene ink was developed from graphene flakes and used to inkjet print the radiating element and the active channel of field effect transistors (FETs). Bending and oxidation tests were carried out to validate the application of printed flexible graphene thin films in flexible electronics. An inkjet-printed graphene-based 1 × 2 element phased array antenna was designed and fabricated. Graphene-based field effect transistors were used as switches in the true-time delay line of the phased array antenna. The graphene phased array antenna was 100% inkjet printed on top of a 5 mil flexible Kapton® substrate, at room temperature. Four possible azimuth steering angles were designed for -26.7°, 0°, 13°, and 42.4°. Measured far-field patterns show good agreement with simulation results.

Ultrawideband, Wide Scanning Stripline-Fed Tightly Coupled Array Antenna Based on Parallel-Dipole Elements

A stripline-fed tightly coupled array antenna with compact size, large scan volume and low cross-polarization characteristics is proposed for ultrawideband (UWB) applications. Simple impedance-matching process is realized by using parallel dual dipoles. Meanwhile, the parallel symmetrical radiating structures minimize the cross-polarization field components dramatically. The mitigation of various undesired resonances is studied in detail. An infinite array is designed to achieve 3:1 bandwidth (6−18 GHz) when scanning ±60∘ in the E-/D-planes (VSWR < 2.5) and H-plane (VSWR < 3.5). The cross-polarization levels remain below −29 dB at broadside. A 16 × 16 prototype is fabricated to demonstrate the design. The measured results are consistent well with the simulated ones. The overall size of the prototype at the lowest operating frequency is 3×3×0.4λ03 (15×15×2cm3). Due to its wide bandwidth, good electronic scan performance and compact size, the proposed antenna array is a good candidate for modern wireless platforms.

Beam Steering with a Nonlinear Optical Phased Array Antenna

Transition metal dichalcogenides (TMDCs) exhibit high second harmonic (SH) generation in the visible due to their noncentrosymmetric crystal structure in odd-layered form and direct bandgap transition when thinned down to a monolayer. In order to emit the SH radiation into a desired direction, one requires a means to control the phase of the in-plane nonlinear polarization. Here, we couple the SH response of a monolayer MoS₂ to an optical phased array antenna and demonstrate controllable steering of the nonlinear emission. By exploiting the intrinsic SH generation by the phased array antenna we achieve uniform emission efficiency into a broad angular range. Our work has relevance for novel optoelectronic applications, such as programmable optical interconnects and on-chip LIDAR.

An X-band Bi-Directional Transmit/Receive Module for a Phased Array System in 65-nm CMOS

We present an X-band bi-directional transmit/receive module (TRM) for a phased array system utilized in radar-based sensor systems. The proposed module, comprising a 6-bit phase shifter, a 6-bit digital step attenuator, and bi-directional gain amplifiers, is fabricated using 65-nm CMOS technology. By constructing passive networks in the phase-shifter and the variable attenuator, the implemented TRM provides amplitude and phase control with 360° phase coverage and 5.625° as the minimum step size while the attenuation range varies from 0 to 31.5 dB with a step size of 0.5 dB. The fabricated T/R module in all of the phase shift states had RMS phase errors of less than 4° and an RMS amplitude error of less than 0.93 dB at 9⁻11 GHz. The output 1dB gain compression point (OP1dB) of the chip was 5.13 dBm at 10 GHz. The circuit occupies 3.92 × 2.44 mm² of the chip area and consumes 170 mW of DC power.

Photonic Multitasking Interleaved Si Nanoantenna Phased Array

Metasurfaces provide unprecedented control over light propagation by imparting local, space-variant phase changes on an incident electromagnetic wave. They can improve the performance of conventional optical elements and facilitate the creation of optical components with new functionalities and form factors. Here, we build on knowledge from shared aperture phased array antennas and Si-based gradient metasurfaces to realize various multifunctional metasurfaces capable of achieving multiple distinct functions within a single surface region. As a key point, we demonstrate that interleaving multiple optical elements can be accomplished without reducing the aperture of each subelement. Multifunctional optical elements constructed from Si-based gradient metasurface are realized, including axial and lateral multifocus geometric phase metasurface lenses. We further demonstrate multiwavelength color imaging with a high spatial resolution. Finally, optical imaging functionality with simultaneous color separation has been obtained by using multifunctional metasurfaces, which opens up new opportunities for the field of advanced imaging and display.