Removal characteristics of microplastics by Fe-based coagulants during drinking water treatment

Microplastics removal from aquatic environment by coagulation: Selecting the best coagulant based on variables determined from a systematic review

The present study was carried out in the two phases of systematic review and experimental research. First, for the systematic review phase, Web of Science, Scopus, and PubMed as electronic databases were utilized to find research articles distributed up to March 5, 2021, related to the removal of microplastics by coagulation. In total, 104 publications were found, of which 14 were reviewed for deriving the variables and research design. Then, in the experimental phase, the experiment was carried out based on the variables derived from the systematic phase for three microplastic types (polyethylene, polystyrene, and polyamide) and five coagulants (polyaluminum chloride (PAC), ferric chloride (FeCl₃), aluminum chloride (AlCl₃), alum (Al(OH)₃) and aluminum sulfate (Al₂(SO₄)₃)) in bench scale study. The differences between removal efficiencies in terms of type, shape, concentration, and size of microplastics within the looked into article was analyzed utilizing ANOVA or Kruskal-Wallis test (for parametric or nonparametric analysis, respectively). The results of experimental phase show that the removal efficiency of different microplastics was significantly different, and it was equal to 65, 22, and 12% on average for PA, PS, and PE, respectively. These averages are much lower than the average removal efficiency calculated in the reviewed articles (78 and 52% for PS and PE, respectively). The removal efficiency of microplastics types by coagulants was not significantly different. As a result, a coagulant that has the lowest dose can be selected as the most suitable coagulant, which is Al(OH)₃ in this study.

Simultaneous removal of microplastics and benzalkonium chloride using electrocoagulation process: statistical modeling and techno-economic optimization

Microplastics and benzyldimethyldodecylammonioum chloride (DDBAC) enter the environment more frequently during the COVID-19 pandemic and their co-occurrence will be a potential threat to the environment in the post-pandemic era. This study investigates the performance of an electrochemical system for the simultaneous removal of microplastics and DDBAC. During experimental studies, effects of applied voltage (3-15 V), pH (4-10), time (0-80 min), electrolyte concentration (0.01-0.0.09 M), electrode configuration, and perforated anode were investigated to identify their influence on DDBAC and microplastics removal efficiency. Eventually, the techno-economic optimization yielded to evaluate the commercial feasibility of this process. The central composite design (CCD) and analysis of variance (ANOVA) are employed for evaluation and optimization of the variables and response, DDBAC-microplastics removal, and for determining the adequacy and significance of mathematical models proposed by response surface methodology (RSM). Experimental results indicate that optimum conditions are pH = 7.4, time = 80 min, electrolyte concentration = 0.05 M, and applied voltage = 12.59, in which the removal of microplastics, DDBAC, and TOC reached the maximum level, which was 82.50%, 90.35%, and 83.60% respectively. The results confirm that the valid model is adequately significant for the target response. Overall, financial and energy consumption analyses confirmed that this process is a promising technology as a commercial method for the removal of DDBAC-microplastics complexes in water and wastewater treatment.

Review of microplastics in the indoor environment: Distribution, human exposure and potential health impacts

The emergence of microplastics (MPs) pollution as a global environmental concern has attracted significant attention in the last decade. The majority of the human population spends most of their time indoors, leading to increased exposure to MPs contamination through various sources such as settled dust, air, drinking water and food. Although research on indoor MPs has intensified significantly in recent years, comprehensive reviews on this topic remain limited. Therefore, this review comprehensively analyses the occurrence, distribution, human exposure, potential health impact and mitigation strategies of MPs in the indoor air environment. Specifically, we focus on the risks associated with finer MPs that can translocate into the circulatory system and other organs, emphasizing the need for continued research to develop effective strategies to mitigate the risks associated with MPs exposure. Our findings suggest that indoor MPs impose potential risk to human health, and strategies for mitigating exposure should be further explored.

Efficiency and mechanism of micro- and nano-plastic removal with polymeric Al-Fe bimetallic coagulants: Role of Fe addition

The occurrence of microplastics (MPs) and even nanoplastics (NPs) in tap water has raised considerable attention. As a pre-treatment and also the most important process in drinking water treatment plants, coagulation has been widely studied to remove MPs, but few studies focused on the removal pattern and mechanism of NPs, especially no study paid attention to the coagulation enhanced by prehydrolysed Al-Fe bimetallic coagulants. Therefore, in this study, polymeric species and coagulation behaviour of MPs and NPs influenced by Fe fraction in polymeric Al-Fe coagulants were investigated. Special attention was given to the residual Al and the floc formation mechanism. The results showed that asynchronous hydrolysis of Al and Fe sharply decreases the polymeric species in coagulants and that the increase of Fe proportion changes the sulfate sedimentation morphology from dendritic to layered structures. Fe weakened the electrostatic neutralization effect and inhibited the removal of NPs but enhanced that of MPs. Compared with monomeric coagulants, the residual Al decreased by 17.4 % and 53.2 % in the MP and NP systems (p < 0.01), respectively. With no new bonds detected in flocs, the interaction between micro/nanoplastics and Al/Fe was merely electrostatic adsorption. According to the mechanism analysis, sweep flocculation and electrostatic neutralization were the dominant removal pathways of MPs and NPs, respectively. This work provides a better coagulant option for removing micro/nanoplastics and minimizing Al residue, which has promising potential for application in water purification.

Microplastic remediation technologies in water and wastewater treatment processes: Current status and future perspectives

Microplastics (MPs) are a type of contaminants produced during the use and disposal of plastic products, which are ubiquitous in our lives. With the high specific surface area and strong hydrophobicity, MPs can adsorb various hazardous microorganisms and chemical contaminants from the environment, causing irreversible damage to our humans. It is reported that the MPs have been detected in infant feces and human blood. Therefore, the presence of MPs has posed a significant threat to human health. It is critically essential to develop efficient, scalable and environmentally-friendly methods to remove MPs. Herein, recent advances in the MPs remediation technologies in water and wastewater treatment processes are overviewed. Several approaches, including membrane filtration, adsorption, chemically induced coagulation-flocculation-sedimentation, bioremediation, and advanced oxidation processes are systematically documented. The characteristics, mechanisms, advantages, and disadvantages of these methods are well discussed and highlighted. Finally, the current challenges and future trends of these methods are proposed, with the aim of facilitating the remediation of MPs in water and wastewater treatment processes in a more efficient, scalable, and environmentally-friendly way.

The suitability and mechanism of polyaluminum-titanium chloride composite coagulant (PATC) for polystyrene microplastic removal: Structural characterization and theoretical calculation

Microplastics (MPs) particles bring potential threats to the aqueous environment, and the coexistence of natural organic matter (NOM) enhances their toxicity. Coagulation is an efficient method for particle removal and exploring the binding sites and modes of the coagulant hydrolysates with MPs in the presence of NOM is essential to understand the coagulation mechanism. In this study, a novel polymerized polyaluminum-titanium chloride composite coagulant (PATC) was prepared and used to remove polystyrene (PS). It was found that PATC could compress or even destroy the surface layer of the negatively charged PS. In comparison to PAC and PTC, PATC was more efficient in decreasing the energy barrier of the PS particles and increasing their aggregation rate over a wider pH range. The results of the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) calculation revealed that the interaction between the hydrolysates of PATC and PS was mainly polar interaction (V_AB), such as hydrogen bonding. The peak intensity and peak shift in Fourier-transformed infrared (FTIR) and X-ray photoelectron spectra (XPS) were analyzed to further explore the interaction between the hydrolysates of PATC and PS. It was found that hydrogen bonding existed between the -OH group of PATC and the aliphatic C-H and C=O groups of PS. And the main interaction between HA and PS was the π-π* conjugation and hydrogen bonding between the -COOH, -OH, and C=O groups of HA and the C=O and aliphatic C-H groups of PS. Therefore, in the HA@PS system, the active sites of HA (e.g. -COOH and -OH) and PS (e.g., C=O and aliphatic C-H) binding with the coagulants were occupied, which accordingly led to the dramatic decline in the removal efficiency of both HA and PS. In actual lake water treatment, although the removal efficiency of PS was significantly poor, PATC performed better for PS removal than PAC and PTC. Besides, the effluent pH was maintained at 6.81±0.08, which met the requirements of the subsequent water treatment process. This study provides systematic knowledge for understanding the interaction between PS, NOM, and coagulant hydrolysates, and further confirms the application potential of PATC for MPs removal.

An assessment of the impact of structure and type of microplastics on ultrafiltration technology for microplastic remediation

Microplastic, which is of size less than 5 mm, is gaining a lot of attention as it has become a new arising contaminant because of its ecophysiology impact on the aquatic environment. These microplastics are found in freshwater or drinking water and are the major carriers of pollutants. Removal of this microplastic can be done through the primary treatment process, secondary treatment process, and tertiary treatment process. One approach for microplastic remediation is ultrafiltration technology, which involves passing water through a membrane with small pores to filter out the microplastics. However, the efficiency of this technology can be affected by the structure and type of microplastics present in the water. New strategies can be created to improve the technology and increase its efficacy in removing microplastics from water by knowing how various types and shapes of microplastics react during ultrafiltration. The filter-based technique, that is, ultrafiltration has achieved the best performance for the removal of microplastic. But with the ultrafiltration, too some microplastic that are of sizes less than of ultrafiltration membrane passes through the filter and enters the food chain. Accumulation of this microplastic on the membrane also leads to membrane fouling. Through this review article, we have assessed the impact of the structure, size, and type of MPs on ultrafiltration technology for microplastic remediation, with that how these factors affect the efficiency of the filtration process and challenges occur during filtration.

A critical review on recent research progress on microplastic pollutants in drinking water

Plastic pollution is an emerging issue in recent days. Persistent plastic particles reach the atmosphere, land and water by multiple pathways. Research has confirmed that the existence of plastic particles is found surprisingly everywhere, from the Artic to the Antarctic region. The probability of ingestion of plastic by all living forms is quite natural, as the whole planet's environment is polluted with microplastic particles. The bioaccumulation of microplastics is a threat and the consequences for living beings are yet to be explored. Microplastics present in different drinking water sources like rivers, lakes, treatment units etc. are studied by several researchers, covering various aspects. Research carried out by various scientists on the microplastics in different drinking water sources is highlighted in this review. In view of the previous research carried out on various aspects of microplastic particles, the necessity of a uniform protocol for qualitative and quantitative analysis of microplastic is ascertained. Microplastic pollution is an ongoing environmental concern, it must be addressed and research should be expanded.

Metal-organic frameworks and plastic: an emerging synergic partnership

Mismanagement of plastic waste results in its ubiquitous presence in the environment. Despite being durable and persistent materials, plastics are reduced by weathering phenomena into debris with a particle size down to nanometers. The fate and ecotoxicological effects of these solid micropollutants are not fully understood yet, but they are raising increasing concerns for the environment and people's health. Even if different current technologies have the potential to remove plastic particles, the efficiency of these processes is modest, especially for nanoparticles. Metal-organic frameworks (MOFs) are crystalline nano-porous materials with unique properties, have unique properties, such as strong coordination bonds, large and robustus porous structures, high accessible surface areas and adsorption capacity, which make them suitable adsorbent materials for micropollutants. This review examines the preliminary results reported in literature indicating that MOFs are promising adsorbents for the removal of plastic particles from water, especially when MOFs are integrated in porous composite materials or membranes, where they are able to assure high removal efficiency, superior water flux and antifouling properties, even in the presence of other dissolved co-pollutants. Moreover, a recent trend for the alternative preparation of MOFs starting from plastic waste, especially polyethylene terephthalate, as a sustainable source of organic linkers is also reviewed, as it represents a promising route for mitigating the impact of the costs deriving from the widescale MOFs production and application. This connubial between MOFs and plastic has the potential to contribute at implementing a more effective waste management and the circular economy principles in the polymer life cycle.

Efficiency of Coagulation/Flocculation for the Removal of Complex Mixture of Textile Fibers from Water

Synthetic fibers enter wastewater treatment plants together with natural fibers, which may affect treatment efficiency, a fact not considered in previous studies. Therefore, the aim of the present study was to evaluate the efficiency of the coagulation/flocculation process for the removal of a mixture of textile fibers from different water matrices. Natural and synthetic fibers (100 mg/L; cotton, polyacrylonitrile, and polyamide) were added to a synthetic matrix, surface water and laundry wastewater and subjected to coagulation/flocculation experiments with ferric chloride (FeCl3) and polyaluminum chloride (PACl) under laboratory conditions. In the synthetic matrix, both coagulants were found to be effective, with FeCl3 having a lesser advantage, removing textile fibers almost completely from the water (up to 99% at a concentration of 3.94 mM). In surface water, all dosages had approximately similar high values, with the coagulant resulting in complete removal. In laundry effluent, the presence of surfactants is thought to affect coagulation efficiency. PACl was found to be effective in removing textile fibers from laundry wastewater, with the lowest removal efficiency being 89% and all dosages having similar removal efficiencies. Natural organic matter and bicarbonates showed a positive effect on the efficiency of FeCl3 in removing textile fibers from surface water. PACl showed better performance in coagulating laundry wastewater while surfactants had a negative effect on FeCl3 coagulation efficiency.

Unaccounted Microplastics in the Outlet of Wastewater Treatment Plants—Challenges and Opportunities

Since the 1950s, plastic production has skyrocketed. Various environmental and human activities are leading to the formation and accumulation of microplastics (MPs) in aquatic and terrestrial ecosystems, causing detrimental effects on water, soil, plants, and living creatures. Wastewater treatment plants (WWTPs) are one of the primary MP management centers meant to check their entry into the natural systems. However, there are considerable limitations in effectively capturing, detecting, and characterizing these MPs in the inlet and outlet of WWTPs leading to “unaccounted MPs” that are eventually discharged into our ecosystems. In order to assess the holistic picture of the MPs’ distribution in the ecosystems, prevent the release of these omitted MPs into the environment, and formulate regulatory policies, it is vital to develop protocols that can be standardized across the globe to accurately detect and account for MPs in different sample types. This review will cover the details of current WWTP adoption procedures for MP management. Specifically, the following aspects are discussed: (i) several processes involved in the workflow of estimating MPs in the outlet of WWTPs; (ii) key limitations or challenges in each process that would increase the uncertainty in accurately estimating MPs; (iii) favorable recommendations that would lead to the standardization of protocols in the workflow and facilitate more accurate analysis of MPs; (iv) research opportunities to tackle the problem of ‘missing MPs’; and (v) future research directions for the efficient management of MPs. Considering the burgeoning research interest in the area of MPs, this work would help early scientists in understanding the current status in the field of MP analysis in the outlet of WWTPs.

Plastic waste management for sustainable environment: techniques and approaches

Excessive exploitation, negligence, non-degradable nature, and physical and chemical properties of plastic waste have resulted in a massive pollution load into the environment. Consequently, plastic entres the food chain and can cause serious health issues in aquatic animals and humans. The present review summarizes currently reported techniques and approaches for the removal of plastic waste. Many techniques, such as adsorption, coagulation, photocatalysis, and microbial degradation, and approaches like reduction, reuse and recycling are potentially in trend and differ from each other in their efficiency and interaction mechanism. Moreover, substantial advantages and challenges associated with these techniques and approaches are highlighted to develop an understanding of the selection of possible ways for a sustainable future. Nevertheless, in addition to the reduction of plastic waste from the ecosystem, many alternative opportunities have also been explored to cash plastic waste. These fields include the synthesis of adsorbents for the removal of pollutants from aqueous and gaseous stream, their utility in clothing, waste to energy and fuel and in construction (road making). Substantial evidence can be observed in the reduction of plastic pollution from various ecosystems. In addition, it is important to develop an understanding of factors that need to be emphasized while considering alternative approaches and opportunities to cash plastic waste (like adsorbent, clothing, waste to energy and fuel). The thrust of this review is to provide readers with a comprehensive overview of the development status of techniques and approaches to overcome the global issue of plastic pollution and the outlook on the exploitation of this waste as resources.

Settling behaviors of microplastic disks in water

Microplastic (MP) disks have not been studied for settling behaviors in aquatic environments, which affects the transport and fate of MPs. Therefore, settling experiments were conducted on MP disks of three shapes and four common-seen materials. Lighter MP disks (with density ρ_s = 1.038 g/cm³ and length l ≤ 5 mm) followed rectilinear vertical trajectories, while heavier MP disks (ρ_s = 1.161-1.343 g/cm³ and l = 5 mm) followed zigzag trajectories with oscillations and rotations. The mean terminal settling velocities of MP disks were 19.6-48.8 mm/s. Instantaneous settling velocities of heavier MP disks fluctuated. Existing formulas could not accurately predict the settling velocity of MP disks; thus, a new model was proposed with an error of 15.5 %. Finally, the Re_d - I* diagram (Re_d is the disk Reynolds number and I* is the dimensionless moment of inertia) was extended for MP disks to predict settling trajectories.

Characterisation of bushfire residuals in source water and removal by coagulation

A bushfire is a spontaneous vegetation fire that can fundamentally affect lives, property, the environment, and even the global climate. Ash from fire carries hazardous pollutants like metal oxides/hydroxides, minerals, black carbons, and by-products of partial combustion, such as hydrocarbons and colloidal charcoal. Bushfire gases and residues can heavily pollute surface and groundwater resources. This paper focuses on the impact of bushfire residue on water quality and explores methods to remediate impacted water supplies. Soils burned in controlled furnace conditions between 150 °C, and 600 °C were characterised, suspended in water, and changes in water quality was measured following leaching from the burned residues. Results indicate that once the soil is burned at temperatures above 300 °C, there is little evidence of leached organic matter. At temperatures below 300 °C, the water discolouration was evident after 24 h leaching, and much higher quantities of leached organic matter were measured. Higher burning temperatures resulted in more alkaline residues. Leachate and charred sample characterisation data shows that the charcoal is highly porous and mainly consists of- amorphous material. The ash is a heterogeneous concoction of smaller particles and comprises significant mineral content. The results also indicate that the primary pollutant among the brushfire residuals is ash which increases pH, alkalinity, turbidity, and UV₂₅₄. Coagulation experiments reveal that dual coagulation systems with metal salts- organic polyelectrolyte reduced the turbidity by 84 %, and dissolved organic carbon (DOC) reduced by 68 % of water containing ash residues. However, some other treatments are needed to reduce the alkalinity.

Recent developments in microplastic contaminated water treatment: Progress and prospects of carbon-based two-dimensional materials for membranes separation

Micro (nano)plastics pollution is a noxious menace not only for mankind but also for marine life, as removing microplastics (MPs) is challenging due to their physiochemical properties, composition, and response toward salinity and pH. This review provides a detailed assessment of the MPs pollution in different water types, environmental implications, and corresponding treatment strategies. With the advancement in nanotechnology, mitigation strategies for aqueous pollution are seen, especially due to the fabrication of nanosheets/membranes mostly utilized as a filtration process. Two-dimensional (2D) materials are increasingly used for membranes due to their diverse structure, affinity, cost-effectiveness, and, most importantly, removal efficiency. The popular 2D materials used for membrane-based organic and inorganic pollutants from water mainly include graphene and MXenes however their effectiveness for MPs removal is still in its infancy. Albeit, the available literature asserts a 70- 99% success rate in micro/nano plastics removal achieved through membranes fabricated via graphene oxide (GO), reduced graphene oxide (rGO) and MXene membranes. This review examined existing membrane separation strategies for MPs removal, focusing on the structural properties of 2D materials, composite, and how they adsorb pollutants and underlying physicochemical mechanisms. Since MPs and other contaminants commonly coexist in the natural environment, a brief examination of the response of 2D membranes to MPs removal was also conducted. In addition, the influencing factors regulate MPs removal performance of membranes by impacting their two main operating routes (filtration and adsorption). Finally, significant limitations, research gaps, and future prospects of 2D material-based membranes for effectively removing MPs are also proposed. The conclusion is that the success of 2D material is strongly linked to the types, size of MPs, and characteristics of aqueous media. Future perspectives talk about the problems that need to be solved to get 2D material-based membranes out of the lab and onto the market.

Microplastics toxicity, detection, and removal from water/wastewater

The world has witnessed massive and preeminent microplastics (MPs) pollution in water bodies due to the inevitable continuous production of plastics for various advantageous chemical and mechanical features. Plastic pollution, particularly contamination by MPs (plastic particles having a diameter lesser than 5 mm), has been a rising environmental concern in recent years due to the inappropriate disposal of plastic trash. This study presents the recent advancements in different technologies for MPs removal in order to gain proper insight into their strengths and weaknesses, thereby orchestrating the preparation for innovation in the field. The production, origin, and global complexity of MPs were discussed. This study also reveals MPs' mode of transportation, its feedstock polymers, toxicities, detection techniques, and the conventional removal strategies of MPs from contaminated systems. Modification of conventional methods vis-à-vis new materials/techniques and other emerging technologies, such as magnetic extraction and sol-gel technique with detailed mechanistic information for the removal of MPs are presented in this study. Conclusively, some future research outlooks for advancing the MPs removal technologies/materials for practical realization are highlighted.

Efficient removal of microplastics from aqueous solution by a novel magnetic biochar: performance, mechanism, and reusability

Microplastics' (MPs) pollution removal from water bodies has become an urgent task to ensure water quality safety and water ecological security on a global scale. In this work, coprecipitation was employed to investigate the adsorption of MPs by magnetic biochar (MRB) prepared from agricultural waste rice husks in an aquatic system. The results showed that MRB can adsorb up to 99.96% of MPs in water; acidic conditions were favorable for the effective MPs' adsorption reaction, and competing anions had a greater effect on adsorption. The adsorption mechanism results revealed that the adsorption of MPs by MRB was a spontaneous process, and electrostatic attraction, surface complexation, hydrogen bonding and π-π interactions were present in the adsorption process. Furthermore, after the adsorption of MPs, MRB can be recovered by thermal treatment (500 °C) and still exhibits up to 90% MPs adsorption (after four uses). This work reveals that MRB is an inexpensive, efficient, and reusable nanoscale adsorbent for MPs pollution removal in water, which may provide new ideas for microplastic pollution control in the aqueous environment.

Surface characteristics of polystyrene microplastics mainly determine their coagulation performances

In this study, polyaluminum sulfate (PAS) coagulant was selected to evaluate the coagulation performance of polystyrene microplastics. Overall, polystyrene removal efficiency was 90.4 % at the optimal dosage of 7.5 g/L of PAS. In addition to the type of coagulants (e.g. polyaluminum chloride, iron(III) chloride, and polyferric sulfate), surface characteristics such as densities, particle sizes, morphologies, adsorbed substances, and functional groups can also significantly impact the coagulation performance. The coagulation ratios are reduced to (2.6 ± 0.1)% when the densities of microplastics decrease. Aging treatments involving NaOH, H₂SO₄, NaClO, CH₃OH, and O₃ promoted coagulation, whereas UV and Na₂S₂O₃ treatments inhibited (64.1 ± 9.7)% and (79.3 ± 8.0)% of polystyrene removals, respectively. In contrast, Fe(NO₃)₃ treatment did not affect the removal ratio. Further characterization of polystyrene before and after coagulation exemplified that the functional groups (CO, CO, and CH) and the rough surfaces of PAS provided adsorption and interception sites for hydrolysis products of the PAS.

The impact of PET microplastic fibres on PVDF ultrafiltration performance - A short-term assessment of MP fouling in simple and complex matrices

Wastewater treatment plants (WWTPs) are key components for the capture of microplastics (MPs) before they are released into natural waterways. Removal efficiencies as high as 99% may be achieved but sub-micron MPs as well as nanoplastics have been overlooked because of analytical limitations. Furthermore, short MP fibres are of concern because of their low capture rate as well as the lack of understanding of their influence on purification system efficiency. This study has investigated the impact of poly(ethylene terephthalate) (PET) short nanofibres on the performance of polyvinylidene fluoride (PVDF) ultrafiltration membranes during cross-flow operation. Model MP fibres with an average length of 10 ± 7 μm and a diameter of 142 ± 40 nm were prepared via a combination of electrospinning and fine cutting using a cryomicrotome. The manufactured MPs were added to both pure and synthetic domestic wastewater at a concentration of 1 mg.L^-1 to determine their impact on the performance of PVDF ultrafiltration membranes. The results show that PET fibres attach to the membrane in a disorganised manner with low pore coverage. The water flux was decreased by 8% for MPs in pure water and no noticeable effect in wastewater after 3 days of filtration. Additionally, the nutrient removal efficiency of the membrane was not altered by the presence of PET MPs. These findings show that MP fibres do not significantly influence the early stages of filtration for a standard concentration of MPs in wastewater treatment plant studies.

Removing microplastics from aquatic environments: A critical review

As one of the typical emerging contaminants, microplastics exist widely in the environment because of their small size and recalcitrance, which has caused various ecological problems. This paper summarizes current adsorption and removal technologies of microplastics in typical aquatic environments, including natural freshwater, marine, drinking water treatment plants (DWTPs), and wastewater treatment plants (WWTPs), and includes abiotic and biotic degradation technologies as one of the removal technologies. Recently, numerous studies have shown that enrichment technologies have been widely used to remove microplastics in natural freshwater environments, DWTPs, and WWTPs. Efficient removal of microplastics via WWTPs is critical to reduce the release to the natural environment as a key connection point to prevent the transfer of microplastics from society to natural water systems. Photocatalytic technology has outstanding pre-degradation effects on microplastics, and the isolated microbial strains or enriched communities can degrade up to 50% or more of pre-processed microplastics. Thus, more research focusing on microplastic degradation could be carried out by combining physical and chemical pretreatment with subsequent microbial biodegradation. In addition, the current recovery technologies of microplastics are introduced in this review. This is incredibly challenging because of the small size and dispersibility of microplastics, and the related technologies still need further development. This paper will provide theoretical support and advice for preventing and controlling the ecological risks mediated by microplastics in the aquatic environment and share recommendations for future research on the removal and recovery of microplastics in various aquatic environments, including natural aquatic environments, DWTPs, and WWTPs.

Effect of Fe and Al based coagulants and disinfectants on polyethylene microplastics removal in coagulation process through response surface methodology

Microplastic (MP) pollution has been rising as a threatening risk and recently has appealed to the attention of more researchers. In this study, influential parameters affecting the removal rate of polyethylene microplastics (PEMPs) were optimized through response surface methodology (RSM). In Box Behnken Design (BBD), independent parameters were pH, PEMP size, coagulant dosage and polyacrylamide dosage. Two experimental sets were conducted, one with ferric chloride and the second with poly aluminum chloride as two commonly applied coagulants in drinking water treatment plants (DWTPs). Comparing the results of optimized parameters, PAC was a better coagulant with the predicted removal rate of 58.19%, while the removal rate with ferric chloride as a coagulant was predicted to be 56.37%. Moreover, some experiments were conducted to analyze the effect of ozone gas and sodium hypochlorite as disinfectants on removal rate. The highest removal rate was observed when 2 ppm of O₃ was added to the solution coagulated with optimal dosage of PAC, reaching the removal rate of 76.8%.

Enhanced coagulation process for removing dissolved organic matter, microplastics, and silver nanoparticles

Dissolved organic carbon (DOC), microplastics (MPs), and silver nanoparticles (AgNPs) in water are of major concern because of their direct and indirect toxic effects on aquatic organisms and human exposure via water. This work investigated the effect of poly aluminum chloride (PACl) coagulation for reducing DOC, MPs, and AgNPs. This work used water from a canal in Thailand with a DOC of 5.2 mg/L in the experiment. AgNPs of 5-20 mg/L were added to canal water to create synthetic water for the PACl coagulation. Polyethylene and polypropylene (PP) type MPs were identified in the raw water with Fourier transform infrared spectroscopy. Coagulation with 15 mg/L of PACl performed better in the PP removal. The PACl coagulation at dosages of 15, 40, and 70 mg/L removed DOC by 16-20%, 44-52%, and 46-63% and AgNPs by 34-90%, 53-93%, and 81-95%, respectively. The presence of AgNPs at high levels could inhibit the efficiency of DOC reduction by the PACl coagulation. The FESEM identified the adsorption of silver-containing nanoparticles onto the flocs with increased dosages of PACl. So, PACl is a coagulant in the removal of AgNPs that can reduce health hazards and eco-toxicological risks in water sources due to the release of silver.

The removal of microplastics from water by coagulation: A comprehensive review

Drinking water treatment plants (DWTPs) and wastewater treatment plants (WWTPs) are the first and last hurdles for the prevention of microplastics (MPs) pollution, respectively. With coagulation as one of the most critical technologies for the removal of MPs in water treatment plants, there is an urgent need to gain an in-depth understanding of the mechanisms and influencing factors of MPs removal during coagulation. In this paper, the research progress of adopting coagulation in MPs removal in recent years is reviewed, the removal effect of coagulation in water treatment plants are compared, and the role of three coagulation mechanisms, i.e., charge neutralization, adsorption bridging, and sweep flocculation in MPs removal process are identified. The effect of coagulant performance, MPs characteristics, operation conditions and other parameters on the removal of MPs are systematically analyzed. It is found that the combined coagulation techniques have better removal efficiency, can better decrease MP pollution and meet strict discharge standards. Moreover, flaws in the application of coagulation technology are pointed out, and strategies to deal with them are also proposed. Hopefully, this review can not only contribute to a better understanding of the mechanism of MPs removal by coagulation technology, but also serve as a useful guide for future research on MPs removal.

Current status of microplastics and nanoplastics removal methods: Summary, comparison and prospect

In modern society, plastics also play an indispensable role in people's lives due to their various excellent properties. However, when these plastic products are discarded after being used, after being subjected to external influences, they will continue to be worn, damaged and degraded into micro- and nano-scale plastics, which are microplastics and nanoplastics (M/NPs). Although people's attention has been paid to M/NPs at present, the focus is still mainly on the detection and hazard of M/NPs, and how to remove M/NPs is relatively less popular. This review was written in order to draw the attention of more researchers to remove M/NPs. This review first briefly introduces the research background of M/NPs, and also shows the main analytical methods currently used for qualitative and quantitative M/NPs. Then, most of the current literature on the removal of M/NPs was collected, and they were classified, summarized, and introduced according to the classification of physical, physicochemical, and biological methods. The advantages and disadvantages of various methods are summarized, and they are also compared, which can help more researchers choose the appropriate method for research. In addition, the application scenarios of these methods are briefly introduced. Finally, some future research directions are proposed for the current research status of M/NPs removal. It is hoped that this will further promote the development on the method of removing M/NPs.

Recent Advances in Micro-/Nanoplastic (MNPs) Removal by Microalgae and Possible Integrated Routes of Energy Recovery

Reliance on plastic has resulted in the widespread occurrence of micro-/nanoplastics (MNPs) in aquatic ecosystems, threatening the food web and whole ecosystem functions. There is a tight interaction between MNPs and microalgae, as dominant living organisms and fundamental constituents at the base of the aquatic food web. Therefore, it is crucial to better understand the mechanisms underlying the interactions between plastic particles and microalgae, as well as the role of microalgae in removing MNPs from aquatic ecosystems. In addition, finding a suitable route for further utilization of MNP-contaminated algal biomass is of great importance. The present review article provides an interdisciplinary approach to elucidate microalgae-MNP interactions and subsequent impacts on microalgal physiology. The degradation of plastic in the environment and differences between micro- and nanoplastics are discussed. The possible toxic effects of MNPs on microalgal growth, photosynthetic activity, and morphology, due to physical or chemical interactions, are evaluated. In addition, the potential role of MNPs in microalgae cultivation and/or harvesting, together with further safe routes for biomass utilization in biofuel production, are suggested. Overall, the current article represents a state-of-the-art overview of MNP generation and the consequences of their accumulation in the environment, providing new insights into microalgae integrated routes of plastic removal and bioenergy production.

Insights into the degradation of microplastics by Fenton oxidation: From surface modification to mineralization

This work aims at evaluating the fate of microplastics (MPs) along Fenton oxidation. For such goal, realistic MPs (150-250 μm) of five representative polymer types (PET, PE, PVC, PP and EPS) were obtained from commercial plastic products by cryogenic milling. Experiments (7.5 h) were performed under relatively severe operating conditions: T = 80 °C; pH₀ = 3; [H₂O₂]₀ = 1000 mgL^-1 (15 doses, 1 every 0.5 h); [Fe³⁺]₀ = 10 mgL^-1 (5 doses, 1 every 1.5 h). Slight MPs weight losses (∼10%) were achieved after Fenton oxidation regardless the MP nature. Nevertheless, oxidation yield clearly increased with decreasing the particle size given their higher exposed surface area (up to 20% weight loss with 20-50 μm EPS MPs). Clearly, MPs suffered important changes in their surface due to the introduction of oxygenated groups, which made them more acidic and hydrophilic. Furthermore, MPs progressively reduced their size. In fact, they can be completely oxidized to CO₂, as demonstrated in the oxidation of PS nanoplastics (140 nm), where 70% mineralization was achieved. The nature of the plastic particles had a relevant impact on its overall oxidation, being more prone to be oxidized those polymers which contain aromatic rings in their structures (EPS and PET) compared to those formed by alkane chains (PE, PP and PVC). In the latter, the presence of substituents also reduced their oxidation potential. Remarkably, possible leachates released along reaction were more quickly oxidized than the MPs/NPs, so it can be assumed that these dissolved compounds would be completely removed once the solid particles are eliminated. Notably, the leachates obtained upon MPs oxidation were more biodegradable than the released from the fresh solids. All this knowledge is crucial for the understanding of MPs oxidation by the Fenton process and opens the door for the design and optimization of this technology either for water treatment or for analytical purposes (MPs isolation).

Nano/microplastics: Fragmentation, interaction with co-existing pollutants and their removal from wastewater using membrane processes

NANO: and microplastic (NP/MP) is one of the most challenging types of micropollutants, coming from either direct release or degradation of plastic items into ecosystems. NP/MP can adsorb hazardous pollutants (such as heavy metals and pharmaceutical compounds) and pathogens onto their surface that are consumed by humans, animals, and aquatic living organisms. This paper presents the interaction of NP/MP with other pollutants in the water environment and mechanisms involved to enable the ultimate fate of NP/MP as well as the effectiveness of metal-organic frame (MOF)-based membrane over conventional membrane processes for NP/MP removal. It is found that conventional membranes could remove MPs when their size is usually more than 1000 nm, but they are ineffective in removing NPs. These NPs have potentially greater health impacts due to their greater surface area. MOF-based membrane could effectively remove both NP and MP due to its large porous structure, high adsorption capacity, and low density. This paper also discusses some challenges associated with MOF-based membranes for NP/MP removal. Finally, we conclude a specific MOF-based ultrafiltration membrane (ED-MIL-101 (Cr)) that can potentially remove both negative and positive charged NP/MP from wastewater by electrostatic attraction and repulsion force with efficient water permeability.

Coagulation and Flocculation before Primary Clarification as Efficient Solutions for Low-Density Microplastic Removal from Wastewater

Microplastic (MP) removal from wastewater was investigated using various types and doses of commercial coagulants (PIX, PAX) and flocculants (FPM, PEL, FCT) before primary clarification in a wastewater treatment plant (WWTP). Dosing with FPM, PIX, and PEL caused small MPs (180-212 µm) to be transferred mainly to the settled sludge (up to 86.4% of MP at a dose of 5 mL FMP/m³), while dosing of FCT and PAX caused these MPs to be transferred to the floated sludge (up to 64% MP at a dose of 5 mL PAX/m³). The efficiency of MP removal from wastewater was the highest (90%) with 2.5 mL PAX/m³; the generated primary sludge had a low MP content and could be safely managed in subsequent stages of sludge treatment. At the highest doses, PIX significantly increased the removal of P-PO₄ (up to 94%) and COD (up to 73%). FPM and FCT resulted in over 40% efficiency of ammonium removal-such disturbance in wastewater composition may negatively affect further biological treatment. Effective removal of MP in the mechanical part of WWTP resulting from coagulation and flocculation enables the safe use of the excess sludge for agricultural purposes.

Microplastics in aquatic systems, a comprehensive review: origination, accumulation, impact, and removal technologies

Although the discovery of plastic in the last century has brought enormous benefits to daily activities, it must be said that its use produces countless environmental problems that are difficult to solve. The indiscriminate use and the increase in industrial production of cleaning, cosmetic, packaging, fertilizer, automotive, construction and pharmaceutical products have introduced tons of plastics and microplastics into the environment. The latter are of greatest concern due to their size and their omnipresence in the various environmental sectors. Today, they represent a contaminant of increasing ecotoxicological interest especially in aquatic environments due to their high stability and diffusion. In this regard, this critical review aims to describe the different sources of microplastics, emphasizing their effects in aquatic ecosystems and the danger to the health of living beings, while examining, at the same time, those few modelling studies conducted to estimate the future impact of plastic towards the marine ecosystem. Furthermore, this review summarizes the latest scientific advances related to removal techniques, evaluating their advantages and disadvantages. The final purpose is to highlight the great environmental problem that we are going to face in the coming decades, and the need to develop appropriate strategies to invert the current scenario as well as better performing removal techniques to minimize the environmental impacts of microplastics.

Elimination of microplastics from the aquatic milieu: A dream to achieve

Microplastics (MPs) have become a significant source of concern as they have emerged as a widespread pollutant that harms the aquatic environment. It has become an enormous challenge, having the capacity to biomagnify and eventually affect human health, biodiversity, aquatic animals, and the environment. This review provides in-depth knowledge of how MPs interact with different toxic organic chemicals, antibiotics, and heavy metals in the aquatic environment and its consequences. Membrane technologies like ultrafiltration (UF), nanofiltration (NF), microfiltration (MF), and dynamic membranes can be highly effective techniques for the removal of MPs. Also, hybrid membrane techniques like advanced oxidation processes (AOPs), membrane fouling, electrochemical processes, and adsorption processes can be incorporated for superior efficiency. The review also focuses on the reactor design and performance of several membrane-based filters and bioreactors to develop practical, feasible, and sustainable membrane technologies. The main aim of this work is to throw light on the alarming scenario of microplastic pollution in the aquatic milieu and strategies that can be adopted to tackle it.

Review on alternatives for the reduction of textile microfibers emission to water

The microplastics (MPs) are considered one of the most threatening pollutants. One of the main concerns is their continuous and cumulative flow to water environments, as they are very difficult to be removed. Microfibers (MFs) are a significant type of MPs, with textile articles as one of the most renowned sources. This review aims to provide the current status of these MFs as pollutants, discussing possible alternatives from the manufacturing until the final disposition of MFs. There are many alternatives to reduce these pollutants from reaching the environment but also gaps that need to be further evaluated and addressed. Besides, it should be noticed that alternatives could be complementary between them. Some viable and non-contaminating solutions to reduce this pollution are currently on the market. Also, one relevant aspect is the final disposition or usage of the retained MFs to avoid them from reaching aquatic environments.

Effect of coagulation on microfibers in laundry wastewater

Microplastics pollution in the aquatic system has received significant attention due to their recalcitrant nature and ecotoxicological threat. Municipal wastewater typically contains various microplastics with synthetic microfibers as a significant constituent from the laundry process. The fate of microfibers in conventional wastewater processes is not clearly understood. In this study, the effect of coagulation on microfibers obtained from a lint screen of a domestic dryer and resuspended in pure water, and also in laundry wastewater was investigated using ferric chloride and polyaluminum chloride (PACl). The removal efficiency of the microfibers resuspended in pure water varied from 86% to 96% depending on the fiber size ranges: < 90 μm, 90-125 μm, and >125 μm with the smaller size microfibers showing a lower removal efficiency. Surfactant present in detergent in laundry wastewater reduced the microfibers removal efficiency to 0-37%, however, the addition of PACl increased microfibers removal to 90%. The optimal PACl concentrations for ≥90% removal were 1.75, 2, 4, and 6 mg/L for 0.5, 2, 4, 8 mg/L detergent, respectively. Zeta potential, FTIR, and SEM analysis were applied to observe the surface changes of microfibers during coagulation indicating possible mechanisms of coagulation. The dominant mechanisms for coagulation of microfibers by FeCl₃ and PACl seem to be charge neutralization and adsorption-bridging. This work provided some insights about the fate of laundry microfibers in primary treatment processes.

Understanding and characteristics of coagulation removal of composite pollution of microplastic and norfloxacin during water treatment

Water composite pollution is still a great challenge in the field of water treatment. Especially for microplastic (MP), as an emerging pollutant, its wide distribution in water and persistent eco-environmental influence have received great concerns in recent years. Nevertheless, the removal characteristics and mechanism of conventional coagulation on MP composite pollution is quite insufficient. In this study, the coagulation removal performance and mechanisms of MP (polyethylene, PE) and norfloxacin (NOR) was investigated by polyaluminium chloride (PAC) and anionic polyacrylamide (APAM). Compared with single system, the removal efficiency of PE was significantly improved (>99.0%) under plateau stage in composite system, while the removal efficiency of NOR was slightly decreased to around 42% regardless of the addition of APAM. The scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), zeta potential and One-way analysis of variance (ANOVA) of experimental data were used to explore the coagulation mechanisms. The results demonstrated that the removal of individual PE and NOR was mainly controlled by charge neutralization and sweep flocculation by PAC and APAM, and adsorption by formation of Al-NOR complex, respectively. Importantly, in composite system, the removal of PE was enhanced not only by the stronger charge neutralization but also the adsorption via the formation of PE-NOR-Al complex. Furthermore, the removal efficiency of PE and NOR in neutral and weak alkaline conditions was higher than that in weak acidic or strong alkaline conditions. The presence of metal ions and humic acid had obvious inhibition and promoting effects on the removal efficiency of PE and NOR. This study can provide a new perspective on fundamental understanding in characteristics and mechanisms of MP composite pollutants removed by coagulation.

Nanomaterials for microplastic remediation from aquatic environment: Why nano matters?

The contamination of microplastics in aquatic environment is regarded as a serious threat to ecosystem especially to aquatic environment. Microplastic pollution associated problems including their bioaccumulation and ecological risks have become a major concern of the public and scientific community. The removal of microplastics from their discharge points is an effective way to mitigate the adverse effects of microplastic pollution, hence has been the central of the research in this realm. Presently, most of the commonly used water or wastewater treatment technologies are capable of removing microplastic to certain extent, although they are not intentionally installed for this reason. Nevertheless, recognizing the adverse effects posed by microplastic pollution, more efforts are still desired to enhance the current microplastic removal technologies. With their structural multifunctionalities and flexibility, nanomaterials have been increasingly used for water and wastewater treatment to improve the treatment efficiency. Particularly, the unique features of nanomaterials have been harnessed in synthesizing high performance adsorbent and photocatalyst for microplastic removal from aqueous environment. This review looks into the potentials of nanomaterials in offering constructive solutions to resolve the bottlenecks and enhance the efficiencies of the existing materials used for microplastic removal. The current efforts and research direction of which studies can dedicate to improve microplastic removal from water environment with the augmentation of nanomaterial-enabled strategies are discussed. The progresses made to date have witnessed the benefits of harnessing the structural and dimensional advantages of nanomaterials to enhance the efficiency of existing microplastic treatment processes to achieve a more sustainable microplastic cleanup.

Optimization of polypropylene microplastics removal using conventional coagulants in drinking water treatment plants via response surface methodology

Background and purpose

The ubiquitous presence of microplastics (MPs) in aquatic environments has been studied widely. Due to toxicological impacts of MPs and associated contaminants, it is crucial to understand the performance of MPs removal in drinking water treatment plants (DWTPs). Few studies have investigated removal characteristics of MPs via coagulation/flocculation processes, yet removal characterization of polypropylene microplastics (PPMPs) in this process is poorly understood. This study aims to optimize coagulation of virgin PPMPs in conventional DWTPs.

Methods

In this study, samples were synthesized through response surface methodology (RSM), polyaluminium chloride (PACl) was applied as a conventional coagulant to remove PPMPs in the coagulation/flocculation process, which has the least density among common polymers and is one of the most abundant manufactured polymers worldwide. A particle size analyzer (PSA) was used to measure floc size at different pH levels. Additionally, a zeta potential analyzer was used to measure stability of the flocs at different pH.

Results

Base on the experimental range in Design-Expert, results revealed that the optimum removal rate was predicted to be at pH 9, PACl concentration of 200 ppm, polyacrylamide (PAM) concentration of 21 ppm, and PPMPs size of d < 0.25 mm. According to the predicted optimum condition, actual and predicted removal rates were 18.00 ± 1.43% and 19.69%, respectively.

Conclusion

According to this study, PACl is not capable of efficiently removing virgin PPMPs in DWTPs, thereby exposing humans to eco-toxicological impacts of PPMPs through tap water.

Critical review of microplastics removal from the environment

Globally, microplastics pollution has become a serious environmental threat due to their multitude sources, widespread occurrence, persistence, and adverse effects to ecosystem and the human health. Addressing this multifaceted threat requires innovative technologies that can efficiently remove microplastics from the environment. In this review, we first overviewed the source, occurrence, and potential adverse impacts of microplastics to human health. We then identified promising technologies for microplastics removal, including physical, chemical, and biological approaches. A detailed analysis of the advantages and limitations of different techniques was provided. We concluded this review with the current challenges and future research priorities, which will guide us through the path addressing microplastics contamination.

Reuse of Water Contaminated by Microplastics, the Effectiveness of Filtration Processes: A Review

Water treatment generally does not specifically address the removal of microplastics (MPs). Nevertheless, treatment plants process water effectively, and the number of synthetic microparticles in effluents is usually very low. Still, discharge volumes from water-treatment plants are often elevated (reaching around 108 L/day), leading to the daily discharge of a substantial number of MPs and microfibers. Furthermore, MPs accumulate in the primary and secondary sludge, which in the end results in another environmental problem as they are currently used to amend soils, both for cultivation and forestry, leading to their dispersion. Something similar occurs with the treatment of water intended for human consumption, which has a much lower but still significant number of MPs. The amount of these pollutants being released into the environment depends on the processes that the water undergoes. One of the most-used treatment processes is rapid sand filtration, which is reviewed in this article. During the filtration process, MPs can break into smaller pieces, resulting in a greater number of plastic particles which mainly accumulate in sewage sludge. Thermal processes, such as incineration, carried out in facilities with the best available techniques in practice, could guarantee the safe disposal of highly MP-contaminated sewage sludges.

Improving nanoplastic removal by coagulation: Impact mechanism of particle size and water chemical conditions

Plastic particles may bring potential threats to the ecosystem. Coagulation, as a widely used method to remove particles, has been rarely studied for plastic particles in the nanometer range. In this work, the coagulation removal of polystyrene nanoplastic particles (PSNPs, 50-1000 nm) was conducted in a model system containing coagulants aluminum chlorohydrate (PAC) and polyacrylamide (PAM). The optimal removal efficiency (98.5%) was observed in the coagulation process at pH= 8.0, 0.4 g·L^-1 PAC and 20 mg·L^-1 PAM. The inhibition impact of humic acid was also noticed, due to its competitive adsorption with PSNPs onto flocs. The interaction energies between PSNPs and PAC were calculated by the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, which showed that electrical neutralization resulted in the difference of the remove efficiency in different sizes and coagulant concentrations. The formation of Al-O bond between PSNPs and PAC/PAM flocs promoted the removal of PSNPs. Excessive PAM (> 20 mg·L^-1) increased clusters size and solution viscosity, which resulted in the settling of clusters being controlled by buoyancy and the reduced remove efficiency. The findings suggest that the chemical coagulation dominants the removal of NPs, and the coagulation efficiency can be optimized by choosing suitable coagulant and water chemical conditions.

Microplastics and nanoplastics: Recent literature studies and patents on their removal from aqueous environment

The presence of microplastics (MP) and nanoplastics (NP) in the environment poses significant hazards towards microorganisms, humans, animals and plants. This paper is focused on recent literature studies and patents discussing the removal process of these plastic pollutants. Microplastics and nanoplastics can be quantified by counting, weighing, absorbance and turbidity and can be further analyzed using scanning electron microscopy (SEM), dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, surface-enhanced Raman spectroscopy and Raman tweezers. Mitigation methods reported are categorized depending on the removal characteristics: (i) Filtration and separation method: Filtration and separation, electrospun nanofiber membrane, constructed wetlands; (ii) Capture and surface attachment method: coagulation, flocculation and sedimentation (CFS), electrocoagulation, adsorption, magnetization, micromachines, superhydrophobic materials and microorganism aggregation; and (iii) Degradation method: photocatalytic degradation, microorganism degradation and thermal degradation; where removal efficiency between 58 and 100% were reported. As these methods are significantly distinctive, the parameters which affect the MP/NP removal performance e.g., pH, type of plastics, presence of interfering chemicals or ions, surface charges etc. are also discussed. 42 granted international patents related to microplastics and nanoplastics removal are also reviewed where the majority of these patents are focused on separation or filtration devices. These devices are efficient for microplastics up to 20 μm but may be ineffective for nanoplastics or fibrous plastics. Several patents were found to focus on methods similar to literature studies e.g., magnetization, CFS, biofilm and microorganism aggregation; with the addition of another method: thermal degradation.

How to Build a Microplastics-Free Environment: Strategies for Microplastics Degradation and Plastics Recycling

Microplastics are an emergent yet critical issue for the environment because of high degradation resistance and bioaccumulation. Unfortunately, the current technologies to remove, recycle, or degrade microplastics are insufficient for complete elimination. In addition, the fragmentation and degradation of mismanaged plastic wastes in environment have recently been identified as a significant source of microplastics. Thus, the developments of effective microplastics removal methods, as well as, plastics recycling strategies are crucial to build a microplastics-free environment. Herein, this review comprehensively summarizes the current technologies for eliminating microplastics from the environment and highlights two key aspects to achieve this goal: 1) Catalytic degradation of microplastics into environmentally friendly organics (carbon dioxide and water); 2) catalytic recycling and upcycling plastic wastes into monomers, fuels, and valorized chemicals. The mechanisms, catalysts, feasibility, and challenges of these methods are also discussed. Novel catalytic methods such as, photocatalysis, advanced oxidation process, and biotechnology are promising and eco-friendly candidates to transform microplastics and plastic wastes into environmentally benign and valuable products. In the future, more effort is encouraged to develop eco-friendly methods for the catalytic conversion of plastics into valuable products with high efficiency, high product selectivity, and low cost under mild conditions.

Conventional and biological treatment for the removal of microplastics from drinking water

This study examines the removal of microplastics and other anthropogenic particles (>10 μm) from surface water by a full-scale conventional drinking water treatment plant. The treatment process is composed of coagulation with aluminum hydroxide, flocculation, anthracite-sand filtration, and chlorination. Samples were also collected from pilot-scale biological filters consisting of anthracite-sand or granular activated carbon (GAC) media operated with or without pre-ozonation and at a range of different empty-bed contact times (EBCTs). Particles in 10 L water samples collected in duplicate using a fully enclosed sampling apparatus were separated using sieves with 500 μm, 300 μm, 125 μm, and 45 μm openings followed by filtration through 10 μm polycarbonate filters. Particles were counted using stereomicroscopy and characterized using μ-Raman spectroscopy. Full-scale conventional treatment removed 52 % of anthropogenic particles when comparing raw (42 ± 18 particles/L) and finished water (20 ± 8 particles/L). Coagulation, flocculation, and sedimentation accounted for the highest removal (70 %) of any individual unit process. Overall removal was reduced to 52 %, the difference being attributed to airborne particle deposition that occurred while water was detained in a clearwell (exposed to atmosphere via ventilation) that was used to achieve the required contact time for disinfection. The majority of the particles (>80 %) were identified as fibers 10-45 μm; microplastics were predominantly composed of polyester while the non-plastic anthropogenic particles were primarily cellulose. None of the pilot filter configurations examined resulted in significantly fewer microplastics when compared to full-scale conventional filtration. This study illustrates that the removal efficiency of conventional treatment may be limited when considering microfibers <45 μm in size.