Pretreatment of lignocellulosic biomass using Fenton chemistry

Fenton-ultrasound treatment of corn stalks enhances humification during composting by stimulating the inheritance and synthesis of polyphenolic compounds-preliminary evidence from a laboratory trial

The impact of Fenton-ultrasound treatment on the production of polyphenols and humic acid (HA) during corn stalk composting was investigated by analyzing the potential for microbial assimilation of polysaccharides in corn stalks to generate polyphenols using a13C-glucose tracer. The results showed that Fenton-ultrasound treatment promoted the decomposition of lignocellulose and increased the HA content, degree of polymerization (DP), and humification index (HI). The primary factor could be attributed to Fenton-ultrasound treatment-induced enhanced the abundance of lignocellulose-degrading microorganisms, as Firmicutes, Actinobacteria phylum and Aspergillis genus, which serve as the primary driving forces behind polyphenol and HA formation. Additionally, the utilization of a13C isotope tracer revealed that corn stalk polysaccharide decomposition products can be assimilated by microbes and subsequently secrete polyphenolic compounds. This study highlights the potential of microbial activity to generate phenolic compounds, offering a theoretical basis for increasing polyphenol production and promoting HA formation during composting.

Hydrodynamic cavitation-assisted acid pretreatment and fed-batch simultaneous saccharification and co-fermentation for ethanol production from sugarcane bagasse using immobilized cells of Scheffersomyces parashehatae

A new alternative for hydrodynamic cavitation-assisted pretreatment of sugarcane bagasse was proposed, along with a simultaneous saccharification and co-fermentation (SSCF) process performed in interconnected columns. Influential variables in the pretreatment were evaluated using a statistical design, indicating that an ozone flow rate of 10 mg min-1 and a pH of 5.10 resulted in 86 % and 72 % glucan and xylan hydrolysis yields, respectively, in the subsequent enzymatic hydrolysis process. Under these optimized conditions, iron sulfate (15 mg L-1) was added to assess Fenton pretreatment, resulting in glucan and xylan hydrolysis yields of 92 % and 71 %, respectively, in a material pretreated for 10 min. In SSCF, ethanol volumetric productivities of 0.33 g L-1 h-1 and of 0.54 g L-1 h-1 were obtained in batch and fed-batch operation modes, achieving 26 g L-1 of ethanol in 48 h in the latter mode.

Effect of heterogeneous fenton-like pretreatment on semi-permeable membrane-covered co-composting: Humification and microbial community succession

This study focused on the impacts of heterogeneous Fenton-like pretreatment on the humification and bacterial community during co-composting of wheat straw with cattle dung covered with a semi-permeable membrane. In this study, FeOCl and low concentration of H2O2 were used for pretreatment and composting, which lasted for 39 days. The results showed that the pretreatment promoted the humification process, with degree of polymerization and percentage of humic acid increasing by 53.2 % and 7.3 %, respectively. Furthermore, the diversity and structure of bacterial communities were altered by pretreatment. During the thermophilic phase, pretreatment considerably promoted the metabolism of carbohydrate. According to redundancy analysis, C/N, moisture and organic matter were the key environmental factors that dominated the microbial community. In summary, heterogeneous Fenton-like pretreatment provided a novel idea for improving the humic acid content and maturity of the compost pile.

Nature-inspired pretreatment of lignocellulose - Perspective and development

As sustainability gains increasing importance in addition to cost-effectiveness as a criterion for evaluating engineering systems and practices, biological processes for lignocellulose pretreatment have attracted growing attention. Biological systems such as white and brown rot fungi and wood-consuming insects offer fascinating examples of processes and systems built by nature to effectively deconstruct plant cell walls under environmentally benign and energy-conservative environments. Research in the last decade has resulted in new knowledge that advanced the understanding of these systems, provided additional insights into these systems' functional mechanisms, and demonstrated various applications of these processes. The new knowledge and insights enable the adoption of a nature-inspired strategy aiming at developing technologies that are informed by the biological systems but superior to them by overcoming the inherent weakness of the natural systems. This review discusses the nature-inspired perspective and summarizes related advancements, including the evolution from biological systems to nature-inspired processes, the features of biological pretreatment mechanisms, the development of nature-inspired pretreatment processes, and future perspective. This work aims to highlight a different strategy in the research and development of novel lignocellulose pretreatment processes and offer some food for thought.

Oxidative pretreatment of lignocellulosic biomass for enzymatic hydrolysis: Progress and challenges

Deconstruction of cell wall structure is important for biorefining of lignocellulose to produce various biofuels and chemicals. Oxidative delignification is an effective way to increase the enzymatic digestibility of cellulose. In this work, the current research progress on conventional oxidative pretreatment including wet oxidation, alkaline hydrogen peroxide, organic peracids, Fenton oxidation, and ozone oxidation were reviewed. Some recently developed novel technologies for coupling pretreatment and direct biomass-to-electricity conversion with recyclable oxidants were also introduced. The primary mechanism of oxidative pretreatment to enhance cellulose digestibility is delignification, especially in alkaline medium, thus eliminating the physical blocking and non-productive adsorption of enzymes by lignin. However, the cost of oxidative delignification as a pretreatment is still too expensive to be applied at large scale at present. Efforts should be made particularly to reduce the cost of oxidants, or explore valuable products to obtain more revenue.

Combined conversion of lignocellulosic biomass into high-value products with ultrasonic cavitation and photocatalytic produced reactive oxygen species - A review

The production of high-value products from lignocellulosic biomass is carried out through the selective scission of crosslinked CC/CO bonds. Nowadays, several techniques are applied to optimize biomass conversion into desired products with high yields. Photocatalytic technology has been proven to be a valuable tool for valorizing biomass at mild conditions. The photoproduced reactive oxygen species (ROSs) can initiate the scission of crosslinked bonds and form radical intermediates. However, the low mass transfer of the photocatalytic process could limit the production of a high yield of products. The incorporation of ultrasonic cavitation in the photocatalytic system provides an exceptional condition to boost the fragmentation and transformation of biomass into the desired products within a lesser reaction time. This review critically discusses the main factors governing the application of photocatalysis for biomass valorization and tricks to boost the selectivity for enhancing the yield of desired products. Synergistic effects obtained through the combination of sonolysis and photocatalysis were discussed in depth. Under ultrasonic vibration, hot spots could be produced on the surface of the photocatalysts, improving the mass transfer through the jet phenomenon. In addition, shock waves can assist the dissolution and mixing of biomass particles.

Stimulating biogas production from steam-exploded birch wood using Fenton reaction and fungal pretreatment

Delignification of steam-exploded birch wood (SEBW) was stimulated using a pretreatment method including Fenton reaction (FR) and fungi. SEBW was employed as a substrate to optimize the Fe(III) and Fe(II) dosage in FR. Maximum iron-binding to SEBW was obtained at pH 3.5. FR pretreatment increased biological methane yields from 257 mL/g vS in control to 383 and 352 mL/ g vS in samples with 0.5 mM Fe(II) and 1.0 mM Fe(III), respectively. Further enzymatic pretreatment using a commercial cellulase cocktail clearly improved methane production rate but only increased the final methane yields by 2-9 %. Finally, pretreatments with the fungi Pleurotus ostreatus (PO) and Lentinula edodes (LE), alone or in combination with FR, were carried out. SEBW pretreated with only LE and samples pretreated with PO and1 mM Fe(III) + H₂O₂ increased the methane production yield to 420 and 419 mL/g vS respectively. These pretreatments delignified SEBW up to 25 %.

Evaluation of electro-oxidation and Fenton pretreatments on industrial fruit waste and municipal sewage sludge to enhance biogas production by anaerobic co-digestion

This study presents the effect of electro-oxidation and Fenton pre-treatment on anaerobic co-digestion (AnCoD) of fruit-juice industrial waste (FJW) and municipal sewage sludge (MSS). Biogas production increased from 767 mL to 857 mL and 918 mL after EO and Fenton pretreatment, respectively. The methane amount increased by 28% and 39% for EO and Fenton processes. The removal efficiencies of soluble COD, carbohydrate, and protein for the conditions with the highest biogas production as a result of the pretreatment process were 48%, 65%, 61% for the Fenton pre-treatment, and 37%, 52%, and 39% for the EO pre-treatment, respectively. Cumulative biogas production efficiency for all pre-treated mixtures was estimated with kinetic models. In addition, an evaluation has been made regarding cost, economic gain, and energy consumption of the pre-treatment processes.

Novel Two-Step Process in Cellulose Depolymerization: Hematite-Mediated Photocatalysis by Lytic Polysaccharide Monooxygenase and Fenton Reaction

To transform cellulose from biomass into fermentable sugars for biofuel production requires efficient enzymatic degradation of cellulosic feedstocks. The recently discovered family of oxidative enzymes, lytic polysaccharide monooxygenase (LPMO), has a high potential for industrial biorefinery, but its energy efficiency and scalability still have room for improvement. Hematite (α-Fe₂O₃) can act as a photocatalyst by providing electrons to LPMO-catalyzed reactions, is low cost, and is found abundantly on the Earth's surface. Here, we designed a composite enzymatic photocatalysis-Fenton reaction system based on nano-α-Fe₂O₃. The feasibility of using α-Fe₂O₃ nanoparticles as a composite catalyst to facilitate LPMO-catalyzed cellulose oxidative degradation in water was tested. Furthermore, a light-induced Fenton reaction was integrated to increase the liquefaction yield of cellulose. The innovative approach finalized the cellulose degradation process with a total liquefaction yield of 93%. Nevertheless, the complex chemical reactions and products involved in this system require further investigation.

A mechanistic study on electro-Fenton system cooperating with phangerochate chrysosporium to degrade lignin

The combined catalytic system of Electro-Fenton (E-Fenton) and Phanerochaete chrysosporium (P. chrysosporium) was constructed in liquid medium with additional potential to overcome the limitations of lignin degradation by white rot fungi alone. To further understand the mechanism of synergistic catalysis, we optimized the optimum potential for lignin catalysis by P. chrysosporium and built synergistic versus separate catalyses. After 48 h of incubation, the optimum growth environment and the highest lignin degradation rate (43.8%) of P. chrysosporium were achieved when 4 V was applied. After 96 h, the lignin degradation rate of the cocatalytic system was 62% (E-Fenton catalysis alone 22% and P. chrysosporium catalysis alone 19%), the pH of the growth maintenance system of P. chrysosporium was approximately 3.5, and the lignin peroxidase (LiP) and manganese-dependent peroxidase (MnP) enzyme activities, were significantly better than those of the control. The qPCR results indicated that the expression of both MnP and LiP genes was higher in the cocatalytic system. Meanwhile, FTIR and 2D-HSQC NMR confirmed that the synergistic catalysis was effective in breaking the aromatic functional groups and the side chains of the aliphatic region of lignin. This study showed that the synergistic catalytic process of electro-Fenton and P. chrysosporium was highly efficient in the degradation of lignin. In addition, the synergetic system is simple to operate, economical and green, and has good prospects for industrial application.

A review on recent developments in hydrodynamic cavitation and advanced oxidative processes for pretreatment of lignocellulosic materials

Environmental problems due to utilization of fossil-derived materials for energy and chemical generation has prompted the use of renewable alternative sources, such as lignocellulose biomass (LB). Indeed, the production of biomolecules and biofuels from LB is among the most important current research topics aiming to development a sustainable bioeconomy. Yet, the industrial use of LB is limited by the recalcitrance of biomass, which impairs the hydrolysis of the carbohydrate fractions. Hydrodynamic cavitation (HC) and Advanced Oxidative Processes (AOPs) has been proposed as innovative pretreatment strategies aiming to reduce process time and chemical inputs. Therefore, the underlying mechanisms, procedural strategies, influence on biomass structure, and research gaps were critically discussed in this review. The performed discussion can contribute to future developments, giving a wide overview of the main involved aspects.

Sugar oxidoreductases and LPMOs - two sides of the same polysaccharide degradation story?

Lytic polysaccharide monooxygenases (LPMOs) catalyze the oxidative cleavage of glycosidic bonds in recalcitrant polysaccharides such as chitin and cellulose and their discovery has revolutionized our understanding of enzymatic biomass conversion. The discovery of LPMOs raises interesting new questions regarding the roles of other oxidoreductases and abiotic redox processes in biomass conversion. LPMOs need reducing power and an oxygen co-substrate and biomass degrading ecosystems contain a multitude of redox enzymes that affect the availability of both. For example, biomass degrading fungi produce multiple sugar oxidoreductases whose biological functions so far have remained somewhat enigmatic. It is now conceivable that these redox enzymes, in particular H2O2-producing sugar oxidases, could play a role in fueling and controlling LPMO reactions. Here, we shortly review contemporary issues in the LPMO field, paying particular attention to the possible roles of sugar oxidoreductases.

Proteomics reveals synergy between biomass degrading enzymes and inorganic Fenton chemistry in leaf-cutting ant colonies

The symbiotic partnership between leaf-cutting ants and fungal cultivars processes plant biomass via ant fecal fluid mixed with chewed plant substrate before fungal degradation. Here we present a full proteome of the fecal fluid of Acromyrmex leaf-cutting ants, showing that most proteins function as biomass degrading enzymes and that ca. 85% are produced by the fungus and ingested, but not digested, by the ants. Hydrogen peroxide producing oxidoreductases were remarkably common in the proteome, inspiring us to test a scenario in which hydrogen peroxide reacts with iron to form reactive oxygen radicals after which oxidized iron is reduced by other fecal-fluid enzymes. Our biochemical assays confirmed that these so-called Fenton reactions do indeed take place in special substrate pellets, presumably to degrade plant cell wall polymers. This implies that the symbiotic partnership manages a combination of oxidative and enzymatic biomass degradation, an achievement that surpasses current human bioconversion technology.

Lignocellulosic crop residue composting by cellulolytic nitrogen-fixing bacteria: A novel tool for environmental sustainability

Lignocellulosic crop residue (LCCR) composting is a cost-effective and sustainable approach for addressing environmental pollution associated with open biomass burning and application of chemical fertilizers in agriculture. The value-added bio-product of the composting process contributes to the improvement of the soil properties and plant growth in an environment-friendly way. However, the conventional process employed for composting LCCRs is slow and becomes an impediment for farmers who plant two or three crops a year. This concern has led to the development of different techniques for rapid composting of LCCRs. The use of cellulolytic nitrogen-fixing microorganisms for composting has emerged as a promising method for enhancing LCCR composting and quality of the compost. Therefore, this review addresses the recent progress on the potential use of cellulolytic nitrogen-fixing bacteria (CNFB) for LCCR composting and discusses various applications of nutrient-rich compost for sustainable agriculture to increase crop yields in a nature-friendly way. This knowledge of bacteria with both cellulose-degrading and nitrogen-fixing activities is significant with respect to rapid composting, soil fertility, plant growth and sustainable management of the lignocellulosic agricultural waste and it provides a means for the development of new technology for sustainability.

Intensification of dilute acid hydrolysis of spent tea powder using ultrasound for enhanced production of reducing sugars

Spent tea (ST) powder is one of the potential sustainable sources available abundantly and can be utilized to produce reducing sugars required for production of platform chemicals. The current study aims at intensifying the reducing sugars production based on ultrasound assisted dilute acid hydrolysis (UADAH). The effects of reaction time, solid liquid ratio, acid concentration and temperature on the yield of reducing sugars were investigated initially for UADAH process based on ultrasonic (US) horn. The highest yield of 24.75 g/L for the reducing sugars was obtained at solid liquid ratio of 1:8, acid concentration of 1% w/v and temperature of 60 °C within 120 min. Use of oxidants like hydrogen peroxide (H₂O₂) and Fenton's reagent to further intensify the production has also been studied. Use of H₂O₂ at optimum loading of 0.75 g/L resulted in reducing sugars yield of 26.2 g/L within 75 min while using same H₂O₂ loading with FeSO₄ at loading of 0.75 g/L along with UADAH reduced the reaction time to 60 min for almost similar yield. Large scale studies performed using US flow cell revealed that yield of reducing sugars as 22.4 g/L is obtained in 120 min in the case of only UADAH, while in the case of UADAH along with H₂O₂ and Fenton's reagent, similar yield of reducing sugars was obtained in only 90 and 60 min respectively. UADAH in combination with oxidants has been demonstrated as an effective and intensified approach to produce reducing sugars from spent tea powder available as sustainable source.

Redesigning the Aspergillus nidulans xylanase regulatory pathway to enhance cellulase production with xylose as the carbon and inducer source

Background

Biomass contains cellulose (C6-sugars), hemicellulose (C5-sugars) and lignin. Biomass ranks amongst the most abundant hydrocarbon resources on earth. However, biomass is recalcitrant to enzymatic digestion by cellulases. Physicochemical pretreatment methods make cellulose accessible but partially destroy hemicellulose, producing a C5-sugar-rich liquor. Typically, digestion of pretreated LCB is performed with commercial cellulase preparations, but C5-sugars could in principle be used for “on site” production of cellulases by genetically engineered microorganism, thereby reducing costs.

Results

Here we report a succession of genetic interventions in Aspergillus nidulans that redesign the natural regulatory circuitry of cellulase genes in such a way that recombinant strains use C5-sugar liquors (xylose) to grow a vegetative tissue and simultaneously accumulate large amounts of cellulases. Overexpression of XlnR showed that under xylose-induction conditions only xylanase C was produced. XlnR overexpression strains were constructed that use the xynCp promoter to drive the production of cellobiohydrolases, endoglucanases and β-glucosidase. All five cellulases accumulated at high levels when grown on xylose. Production of cellulases in the presence of pretreated-biomass C5-sugar liquors was investigated, and cellulases accumulated to much higher enzyme titers than those obtained for traditional fungal cell factories with cellulase-inducing substrates.

Conclusions

By replacing expensive substrates with a cheap by-product carbon source, the use of C5-sugar liquors directly derived from LCB pretreatment processes not only reduces enzyme production costs, but also lowers operational costs by eliminating the need for off-site enzyme production, purification, concentration, transport and dilution.

Multiple iron reduction by methoxylated phenolic lignin structures and the generation of reactive oxygen species by lignocellulose surfaces

Chelator-mediated Fenton chemistry is capable of reducing non-stochiometric amounts of iron via hydroquinone oxidation. These types of reactions have previously been demonstrated to be promoted by some lignocellulose degrading fungi in generating hydroxyl radicals to permit lignified plant cell wall deconstruction. Here we demonstrate that lignocellulose surfaces, when exposed by chemical treatment or fragmentation, can promote a similar multi-oxidative mechanism in the presence of iron. Iron reduction by lignin surfaces permits the generation of hydroxyl radicals in the cell wall to help explain fungal non-enzymatic cell wall deconstruction, and it also provides an explanation for certain phenomenon such as the anthropogenic generation of formaldehyde by wood. The mechanism also provides a basis for the generation of electrons by lignin that are required by certain fungal redox enzymes active in plant cell wall degrading systems. Overall, the data demonstrate that iron found naturally in lignocellulose materials will promote the oxidation of phenolic lignin compounds in the naturally low pH environments occurring within lignified plant cell walls, and that this activity is promoted by cell wall fragmentation.

Oxidoreductases and Reactive Oxygen Species in Conversion of Lignocellulosic Biomass

Biomass constitutes an appealing alternative to fossil resources for the production of materials and energy. The abundance and attractiveness of vegetal biomass come along with challenges pertaining to the intricacy of its structure, evolved during billions of years to face and resist abiotic and biotic attacks. To achieve the daunting goal of plant cell wall decomposition, microorganisms have developed many (enzymatic) strategies, from which we seek inspiration to develop biotechnological processes. A major breakthrough in the field has been the discovery of enzymes today known as lytic polysaccharide monooxygenases (LPMOs), which, by catalyzing the oxidative cleavage of recalcitrant polysaccharides, allow canonical hydrolytic enzymes to depolymerize the biomass more efficiently. Very recently, it has been shown that LPMOs are not classical monooxygenases in that they can also use hydrogen peroxide (H2O2) as an oxidant. This discovery calls for a revision of our understanding of how lignocellulolytic enzymes are connected since H2O2 is produced and used by several of them. The first part of this review is dedicated to the LPMO paradigm, describing knowns, unknowns, and uncertainties. We then present different lignocellulolytic redox systems, enzymatic or not, that depend on fluxes of reactive oxygen species (ROS). Based on an assessment of these putatively interconnected systems, we suggest that fine-tuning of H2O2 levels and proximity between sites of H2O2 production and consumption are important for fungal biomass conversion. In the last part of this review, we discuss how our evolving understanding of redox processes involved in biomass depolymerization may translate into industrial applications.

Effect of iron salt type and dosing mode on Fenton-based pretreatment of rice straw for enzymatic hydrolysis

Fenton-based processes with four different iron salts in two different dosing modes were used to pretreat rice straw (RS) samples to increase their enzymatic digestibility. The composition analysis shows that the RS sample pretreated by the dosing mode of iron salt adding into H₂O₂ has a much lower hemicellulose content than that pretreated by the dosing mode of H₂O₂ adding into iron salt, and the RS sample pretreated by the chloride salt-based Fenton process has a much lower lignin content and a slightly lower hemicellulose content than that pretreated by the sulphate salt-based Fenton process. The higher concentration of reducing sugar observed on the RS sample with lower lignin and hemicellulose contents justifies that the Fenton-based process could enhance the enzymic hydrolysis of RS by removing hemicellulose and lignin and increasing its accessibility to cellulase. FeCl₃·6H₂O adding into H₂O₂ is the most efficient Fenton-based process for RS pretreatment.

Transformation of oil palm fronds into pentose sugars using copper (II) sulfate pentahydrate with the assistance of chemical additive

Among the chemical pretreatments available for pretreating biomass, the inorganic salt is considered to be a relatively new but simple reagent that offers comparable pentose (C5) sugar recoveries as the conventional dilute acid hydrolysis. This study investigated the effects of different concentrations (1.5-6.0% (v/v)) of H₂O₂ or Na₂S₂O₈ in facilitating CuSO₄·5H₂O pretreatment for improving pentose sugar recovery from oil palm fronds. The best result was observed when 0.2 mol/L of CuSO₄·5H₂O was integrated with 4.5% (v/v) of Na₂S₂O₈ to recover 8.2 and 0.9 g/L of monomeric xylose and arabinose, respectively in the liquid fraction. On the other hand, an addition of 1.5% (v/v) of H₂O₂ yielded approximately 74% lesser total pentose sugars as compared to using 4.5% (v/v) Na₂S₂O₈. By using CuSO₄·5H₂O alone (control), only 0.8 and 1.0 g/L xylose and arabinose, respectively could be achieved. The results mirrored the importance of using chemical additives together with the inorganic salt pretreatment of oil palm fronds. Thus, an addition of 4.5% (v/v) of Na₂S₂O₈ during CuSO₄·5H₂O pretreatment of oil palm fronds at 120 °C and 30 min was able to attain a total pentose sugar yield up to ∼40%.

Lignocellulosic Biomass Transformations via Greener Oxidative Pretreatment Processes: Access to Energy and Value-Added Chemicals

Anthropogenic climate change, principally induced by the large volume of carbon dioxide emission from the global economy driven by fossil fuels, has been observed and scientifically proven as a major threat to civilization. Meanwhile, fossil fuel depletion has been identified as a future challenge. Lignocellulosic biomass in the form of organic residues appears to be the most promising option as renewable feedstock for the generation of energy and platform chemicals. As of today, relatively little bioenergy comes from lignocellulosic biomass as compared to feedstock such as starch and sugarcane, primarily due to high cost of production involving pretreatment steps required to fragment biomass components via disruption of the natural recalcitrant structure of these rigid polymers; low efficiency of enzymatic hydrolysis of refractory feedstock presents a major challenge. The valorization of lignin and cellulose into energy products or chemical products is contingent on the effectiveness of selective depolymerization of the pretreatment regime which typically involve harsh pyrolytic and solvothermal processes assisted by corrosive acids or alkaline reagents. These unselective methods decompose lignin into many products that may not be energetically or chemically valuable, or even biologically inhibitory. Exploring milder, selective and greener processes, therefore, has become a critical subject of study for the valorization of these materials in the last decade. Efficient alternative activation processes such as microwave- and ultrasound irradiation are being explored as replacements for pyrolysis and hydrothermolysis, while milder options such as advanced oxidative and catalytic processes should be considered as choices to harsher acid and alkaline processes. Herein, we critically abridge the research on chemical oxidative techniques for the pretreatment of lignocellulosics with the explicit aim to rationalize the objectives of the biomass pretreatment step and the problems associated with the conventional processes. The mechanisms of reaction pathways, selectivity and efficiency of end-products obtained using greener processes such as ozonolysis, photocatalysis, oxidative catalysis, electrochemical oxidation, and Fenton or Fenton-like reactions, as applied to depolymerization of lignocellulosic biomass are summarized with deliberation on future prospects of biorefineries with greener pretreatment processes in the context of the life cycle assessment.

Efficient pretreatment of lignocellulosic biomass with high recovery of solid lignin and fermentable sugars using Fenton reaction in a mixed solvent

BACKGROUND

Pretreatment of biomass to maximize the recovery of fermentable sugars as well as to minimize the amount of enzyme inhibitors formed during the pretreatment is a challenge in biofuel process. We develop a modified Fenton pretreatment in a mixed solvent (water/DMSO) to combine the advantages of organosolv and Fenton pretreatments. The hemicellulose and cellulose in corncob were effectively degraded into xylose, glucose, and soluble glucose oligomers in a few hours. This saccharide solution, separated from the solid lignin simply by filtration, can be directly applied to the subsequent enzymatic hydrolysis and ethanol fermentation.

RESULTS

After the pretreatment, 94% carbohydrates were recovered as soluble monosaccharide (xylose and glucose) and glucose oligomers in the filtrates, and 87% of solid lignin was recovered as the filter residue. The filtrates were directly applied to enzymatic hydrolysis, and 92% of raw corncob glucose was recovered. The hydrolysates containing the glucose and xylose from the enzymatic hydrolysis were directly applied to ethanol fermentation with ethanol yield equals 79% of theoretical yield. The pretreatment conditions (130 °C, 1.5 bar; 30 min to 4 h) are mild, and the pretreatment reagents (H₂O₂, FeCl₃, and solvent) had low impact to environment. Using ferrimagnetic Fe₃O₄ resulted in similar pretreatment efficiency and Fe₃O₄ could be removed by filtration.

CONCLUSIONS

A modified Fenton pretreatment of corncob in DMSO/water was developed. Up to 94% of the carbohydrate content of corncob was recovered as a saccharide solution simply by filtration. Such filtrate was directly applied to the subsequent enzymatic hydrolysis and where 92% of the corncob glucose content was obtained. The hydrolysate so obtained was directly applied to ethanol fermentation with good fermentability. The pretreatment method is simple, and the additives and solvents used have a low impact to the environment. This method provides the opportunity to substantially maximize the carbohydrate and solid lignin recovery of biomass with a comparatively green process, such that the efficiency of biorefinery as well as the bioethanol production process can be improved. The pretreatment is still relatively energy intensive and expensive, and further optimization of the process is required in large-scale operation.

Persulfate oxidation assisted hydrochar production from Platanus Orientalis Leaves: Physiochemical and combustion characteristics

Platanus Orientalis Leaves (POL), a widely planted tree in parks and along streets, was employed by sequential persulfate oxidation (Fe²⁺and persulfate) and hydrothermal treatment (HTC) to improve the thermal stability, energy yield and combustion behavior of hydrochars (HCs). Higher heating values (HHVs) of HCs derived from persulfate pretreated POL was increased by 30.5% at mild HTC temperature (i.e., 210°C) as compared to char without pretreatment. Elevating Fe²⁺/persulfate ratio to 0.2 enables HCs with high fractions of lignin, thus promoting the energy yield going up to 64.4%. The ultimate and proximate analysis, N₂ adsorption-desorption isotherms, FT-IR spectroscopy and thermogravimetric analysis were conducted to probe into chars' physiochemical and combustion characteristics. Results indicated that persulfate pretreatment on POL strengthened efficient HTC conversion from volatile matter to fixed carbon, increasing the ignition temperature of HCs from 261.5 to 404.3°C as compared to the char obtained with only HTC.

Ferric chloride assisted plasma pretreatment of lignocellulose

In this study, a novel pretreatment for spent coffee waste (SCW) has been proposed which combines two techniques viz. atmospheric air plasma and FeCl₃ to create a superior pretreatment that involves Fenton chemistry. The pretreatment was optimised employing Taguchi Design of Experiments, and five parameters were taken into consideration viz. biomass loading, FeCl₃ concentration, H₂SO₄ concentration, plasma discharge voltage and treatment time. The composition analysis of the pretreated SCW revealed substantial amounts of lignin removal, with a maximum for process conditions of 70kV for 2min in an acidic environment containing 1% H₂SO₄. FTIR, XRD and DSC were performed to characterise the samples. The pretreated SCW after enzymatic hydrolysis yielded 0.496g of reducing sugar/g of SCW. The hydrolysate was subjected to fermentation by S. cerevisiae and led to the production of 18.642g/l of ethanol with a fermentation efficiency of 74%, which was a two fold increase in yield compared to the control.

Pretreatment of rice straw by ultrasound-assisted Fenton process

Fenton's reagent, ultrasound, and the combination of Fenton's reagent and ultrasound were used to pretreat rice straw (RS) to increase its enzymatic digestibility for saccharification. The characterization shows that compared with ultrasound, Fenton's reagent pretreatment was more efficient in increasing the specific surface area and decreasing the degree of polymerization (DP) of RS. The enzymatic hydrolysis results showed that the RS pretreated by ultrasound-assisted Fenton's reagent (U/F-RS), which exhibited the largest specific surface area and the lowest DP value, had the highest enzymatic activity, and the amount of reducing sugar released from U/F-RS at 48h of enzymatic saccharification is about 4 times as large as that from raw RS and 1.5 times as large as that from Fenton's reagent pretreated RS. The ultrasound-assisted Fenton process provides a reliable and effective method for RS pretreatment.

Persulfate based pretreatment to enhance the enzymatic digestibility of rice straw

Oxidation induced by potassium persulfate was evaluated as an economic substitute for the Fenton-like reaction for the purpose of rice straw pretreatment in terms of temperature (80-140°C), potassium persulfate concentration (5-100mM) and process time (0.5-3h), an optimal pretreatment condition was identified: 120°C for 2 h with 75mM potassium persulfate concentration and yielded 91% enzymatic digestibility using 25.2FPU/g of biomass. Crystallinity index, SEM and SEM-EDS analyses revealed that biomass was indeed disrupted and components like silica were exposed. All this suggested that this persulfate-based pretreatment method, which is distinctively advantageous in terms of effectiveness and economics, can indeed be a competitive option.

Involvement of Fenton chemistry in rice straw degradation by the lignocellulolytic bacterium Pantoea ananatis Sd-1

BACKGROUND

Lignocellulolytic bacteria have revealed to be a promising source for biofuel production, yet the underlying mechanisms are still worth exploring. Our previous study inferred that the highly efficient lignocellulose degradation by bacterium Pantoea ananatis Sd-1 might involve Fenton chemistry (Fe²⁺ + H₂O₂ + H⁺ → Fe³⁺ + OH· + H₂O), similar to that of white-rot and brown-rot fungi. The aim of this work is to investigate the existence of this Fenton-based oxidation mechanism in the rice straw degradation process of P. ananatis Sd-1.

RESULTS

After 3 days incubation of unpretreated rice straw with P. ananatis Sd-1, the percentage in weight reduction of rice straw as well as its cellulose, hemicellulose, and lignin components reached 46.7, 43.1, 42.9, and 37.9 %, respectively. The addition of different hydroxyl radical scavengers resulted in a significant decline (P < 0.001) in rice straw degradation. Pyrolysis gas chromatography-mass spectrometry and Fourier transform infrared spectroscopy analysis revealed the consistency of chemical changes of rice straw components that exists between P. ananatis Sd-1 and Fenton reagent treatment. In addition to the increased total iron ion concentration throughout the rice straw decomposition process, the Fe³⁺-reducing capacity of P. ananatis Sd-1 was induced by rice straw and predominantly contributed by aromatic compounds metabolites. The transcript levels of the glucose-methanol-choline oxidoreductase gene related to hydrogen peroxide production were significantly up-regulated (at least P < 0.01) in rice straw cultures. Higher activities of GMC oxidoreductase and less hydrogen peroxide concentration in rice straw cultures relative to glucose cultures may be responsible for increasing rice straw degradation, which includes Fenton-like reactions.

CONCLUSIONS

Our results confirmed the Fenton chemistry-assisted degradation model in P. ananatis Sd-1. We are among the first to show that a Fenton-based oxidation mechanism exists in a bacteria degradation system, which provides a new perspective for how natural plant biomass is decomposed by bacteria. This degradative system may offer an alternative approach to the fungi system for lignocellulosic biofuels production.

Direct conversion of cellulose and hemicellulose to fermentable sugars by a microbially-driven Fenton reaction

The aim of this work was to develop a microbially-driven Fenton reaction that fragments cellulose and hemicellulose, degrades cellodextrins and xylodextrins, and produces short-chain oligosaccharides and monomeric sugars in a single bioreactor. The lignocellulose degradation system operates at neutral pH and does not require addition of conventional lignocellulose-degrading enzymes, thus avoiding problems associated with enzyme accessibility and specificity. The ability to produce useful bioproducts was demonstrated by production of the bioplastic polyhydroxybutyrate with the xylan degradation products as starting substrate.

Enhancing enzymolysis and fermentation efficiency of sugarcane bagasse by synergistic pretreatment of Fenton reaction and sodium hydroxide extraction

A study on the synergistic pretreatment of sugarcane bagasse (SCB) using Fenton reaction and NaOH extraction was conducted. The optimized process conditions for Fenton pretreatment were 10% (w/w) of H2O2, 20mM of Fe(2+), pH 2.5, pretreatment time 6h, and pretreatment temperature 55°C. Sequential pretreatments were performed in combination with NaOH extraction (NaOH 1% (w/w), 80°C, 5% of solid loading, 1h). Among all the pretreatments, Fenton pretreatment followed by NaOH extraction had the highest efficiency of 64.7% and 108.3% for enzymolysis and simultaneous saccharification fermentation (SSF) with an ethanol concentration of 17.44g/L. The analyses by the scanning electron microscopy, X-ray diffraction and confocal laser scanning microscopy revealed that Fenton pretreatment disrupts the structure of SCB to facilitate the degradation of lignin by NaOH. The overall data suggest that this combinatorial strategy is a promising process for SCB pretreatment.

Depolymerization of microcrystalline cellulose by the combination of ultrasound and Fenton reagent

In this study, the combined use of Fenton reagent and ultrasound to the pretreatment of microcrystalline cellulose (MCC) for subsequent enzyme hydrolysis was investigated. The morphological analysis showed that the aspect ratio of MCC was greatly reduced after pretreatment. The X-ray diffraction (XRD) and degree of polymerization (DP) analyses showed that Fenton reagent was more efficient in decreasing the crystallinity of MCC while ultrasound was more efficient in decreasing the DP of MCC. The combination of Fenton reaction and ultrasound, which produced the lowest crystallinity (84.8 ± 0.2%) and DP (124.7 ± 0.6) of MCC and the highest yield of reducing sugar (22.9 ± 0.3 g/100 g), provides a promising pretreatment process for MCC depolymerization.

Enhancement of sludge anaerobic biodegradability by combined microwave-H2O2 pretreatment in acidic conditions

The aim of this study was to increase the sludge disintegration and reduce the cost of microwave (MW) pretreatment. Thermodynamic analysis of MW hydrolysis revealed the best fit with a first-order kinetic model at a specific energy of 18,600 kJ/kg total solids (TS). Combining H2O2 with MW resulted in a significant increment in solubilization from 30 to 50 % at 18,600 kJ/kg TS. The pH of H2O2-assisted MW-pretreated sludge (MW + H2O2) was in the alkaline range (pH 9-10), and it made the sludge unfavorable for subsequent anaerobic digestion and inhibits methane production. In order to nullify the alkaline effect caused by the MW + H2O2 combination, the addition of acid was considered for pH adjustment. H2O2-assisted MW-pretreated sludge in acidic conditions (MW + H2O2 + acid) showed a maximum methane production of 323 mL/g volatile solids (VS) than others during anaerobic biodegradability. A cost analysis of this study reveals that MW + H2O2 + acid was the most economical method with a net profit of 59.90 €/t of sludge.

Comparison of ultrasound-assisted Fenton reaction and dilute acid-catalysed steam explosion pretreatment of corncobs: cellulose characteristics and enzymatic saccharification

As an emerging method for lignocellulose pretreatment, the ultrasound-assisted Fenton reaction is not well developed in comparison to the dilute acid-catalysed steam explosion.

Sequential Fenton oxidation and hydrothermal treatment to improve the effect of pretreatment and enzymatic hydrolysis on mixed hardwood

Sequential Fenton oxidation (FO) and hydrothermal treatment were performed to improve the effect of pretreatment and enzymatic hydrolysis of mixed hardwood. The molar ratio of the Fenton reagent (FeSO4·7H2O and H2O2) was 1:25, and the reaction time was 96h. During the reaction, little or no weight loss of biomass was observed. The concentration of Fe(2+) was determined and was found to increase continuously during FO. Hydrothermal treatment at 190-210°C for 10-80min was performed following FO. Sequential FO and hydrothermal treatment showed positive effects on pretreatment and enzymatic hydrolysis. Xylose concentration in the hydrolysate was as high as 14.16g/L when FO-treated biomass was treated at 190°C, while its concentration in the raw material was 3.72g/L. After 96h of enzymatic hydrolysis, cellulose conversion in the biomass obtained following sequential treatment was 69.58-79.54%. In contrast, the conversion in the raw material (without FO) was 64.41-67.92%.

Enhancement of enzymatic saccharification of corn stover with sequential Fenton pretreatment and dilute NaOH extraction

In this study, an effective method by the sequential Fenton pretreatment and dilute NaOH extraction (FT-AE) was chosen for pretreating corn stover. Before dilute NaOH (0.75 wt%) extraction at 90 °C for 1h, Fenton reagent (0.95 g/L of FeSO4 and 29.8 g/L of H2O2) was employed to pretreat CS at a solid/liquid ratio of 1/20 (w/w) at 35 °C for 30 min. The changes in the cellulose structural characteristics (porosity, morphology, and crystallinity) of the pretreated solid residue were correlated with the enhancement of enzymatic saccharification. After being enzymatically hydrolyzed for 72 h, the reducing sugars and glucose from the hydrolysis of 60 g/L FT-AE-CS pretreated could be obtained at 40.96 and 23.61 g/L, respectively. Finally, the recovered hydrolyzates containing glucose had no inhibitory effects on the ethanol fermenting microorganism. In conclusion, the sequential Fenton pretreatment and dilute NaOH extraction has high potential application in future.

Enhancing methane production from waste activated sludge using a novel indigenous iron activated peroxidation pre-treatment process

Methane production from anaerobic digestion of waste activated sludge (WAS) is limited by the slow hydrolysis rate and/or poor methane potential of WAS. This study presents a novel pre-treatment strategy based on indigenous iron (in WAS) activated peroxidation to enhance methane production from WAS. Pre-treatment of WAS for 30 min at 50mg H2O2/g total solids (dry weight) and pH 2.0 (iron concentration in WAS was 7 mg/g TS) substantially enhanced WAS solubilization. Biochemical methane potential tests demonstrated that methane production was improved by 10% at a digestion time of 16d after incorporating the indigenous iron activated peroxidation pre-treatment. Model-based analysis indicated that indigenous iron activated peroxidation pre-treatment improved the methane potential by 13%, whereas the hydrolysis rate was not significantly affected. The economic analysis showed that the proposed pre-treatment method can save the cost by $112,000 per year in a treatment plant with a population equivalent of 300,000.

Mimicking the Fenton reaction-induced wood decay by fungi for pretreatment of lignocellulose

In this study, the Fenton reaction, which is naturally used by fungi for wood decay, was employed to pretreat rice straw and increase the enzymatic digestibility for the saccharification of lignocellulosic biomass. Using an optimized Fenton's reagent (FeCl3 and H2O2) for pretreatment, an enzymatic digestibility that was 93.2% of the theoretical glucose yield was obtained. This is the first report of the application of the Fenton reaction to lignocellulose pretreatment at a moderate temperature (i.e., 25°C) and with a relatively high loading of biomass (i.e., 10% (w/v)). Substantial improvement in the process economics of cellulosic fuel and chemical production can be achieved by replacing the conventional pretreatment with this Fenton-mimicking process.