Occurrence, behavior and effects of nanoparticles in the environment

Reduced bioavailability of Au and isotopically enriched 109Ag nanoparticles transformed through a pilot wastewater treatment plant in Hyalella azteca under environmentally relevant exposure scenarios

Wastewater Treatment Plants (WWTP) are a major repository and entrance path of nanoparticles (NP) in the environment and hence play a major role in the final NP fate and toxicity. Studies on silver nanoparticles (AgNP) transport via the WWTP system and uptake by aquatic organisms have so far been carried out using unrealistically high AgNP concentrations, unlikely to be encountered in the aquatic environment. The use of high AgNP concentrations is necessitated by both the low sensitivity of the detection methods used and the need to distinguish background Ag from spiked AgNP. In this study, isotopically enriched 109AgNP were synthesized to overcome these shortcomings and characterized by a broad range of methods including transmission electron microscopy, dynamic and electrophoretic light scattering. 109AgNP and gold NP (AuNP) were spiked to a pilot wastewater treatment plant fed with municipal wastewater for up to 21 days. AuNP were used as chemically less reactive tracer. The uptake of the pristine and transformed NP present in the effluent was assessed using the benthic amphipod Hyalella azteca in fresh- and brackish water exposures at environmentally relevant concentrations of 30 to 500 ng Au/L and 39 to 260 ng Ag/L. The unique isotopic signature of the 109AgNP allowed to detect the material at environmentally relevant concentrations in the presence of a much higher natural Ag background. The results show that the transformations reduce the NP uptake at environmentally relevant exposure concentrations. For 109Ag, lower accumulation factors (AF) were obtained after exposure to transformed NP (250-350) compared to the AF values obtained for pristine 109AgNP (750-840). The reduced AF values observed for H. azteca exposed to effluent from the AuNP-spiked WWTP indicate that biological transformation processes (e.g. eco-corona formation) seem to be involved in addition to chemical transformation.

Environmental applications and risks of engineered nanomaterials in removing petroleum oil in soil

Oil-contaminated soil posed serious threats to the ecosystems and human health. The unique and tunable properties of engineered nanomaterials (ENMs) enable new technologies for removing and repairing oil-contaminated soil. However, few studies systematically examined the linkage between the change of physicochemical properties and the removal efficiency and environmental functions (e.g., potential risk) of ENMs, which is vital for understanding the ENMs environmental sustainability and utilization as a safety product. Thus, this review briefly summarized the environmental applications of ENMs to removing petroleum oil from complex soil systems: Theoretical and practical fundamentals (e.g., excellent physicochemical properties, environmental stability, controlled release, and recycling technologies), and various ENMs (e.g., iron-based, carbon-based, and metal oxides nanomaterials) remediation case studies. Afterward, this review highlights the removing mechanism (e.g., adsorption, photocatalysis, oxidation/reduction, biodegradation) and the impact factor (e.g., nanomaterials species, natural organic matter, and soil matrix) of ENMs during the remediation process in soil ecosystems. Both positive and negative effects of ENMs on terrestrial organisms have been identified, which are mainly derived from their diverse physicochemical properties. In linking nanotechnology applications for repairing oil-contaminated soil back to the physical and chemical properties of ENMs, this critical review aims to raise the research attention on using ENMs as a fundamental guide or even tool to advance soil treatment technologies.

Adsorption performance of nanoplastics in carbon filtration column

Nanoplastics (NPs) are usually formed by the decomposition of large plastics, which will cause water pollution after entering the water body. Carbon filter column is used to adsorb and remove polystyrene nanoparticles (PSNPs). The influence of experimental conditions on adsorption was investigated and fitted by kinetic model. The results show that increasing the height of carbon filter column and decreasing the initial concentration of PSNPs and water flow rate can prolong the breakthrough time of carbon filter column. When the initial concentration of PSNPs is 0.8 mg L-1, the influent flow rate is 4 mL min-1 and the height of carbon filter bed is 8.5 cm, the removal effect is the best, and the depletion point of carbon filter column is extended to 48 h. Adams-Bohart model is suitable for describing the initial stage of adsorption. Thomas and Yoon-Nelson models can well describe the whole dynamic adsorption process of PSNPs, and Yoon-Nelson model can accurately predict the time required for 50% PSNPs to penetrate the carbon column. The adsorption mechanism of NPs by carbon filter column is mainly through the attachment sites and pore retention provided by particles on the surface of activated carbon. This study can provide new technical and theoretical support for the removal of NPs.

Amino-modified polystyrene nanoplastics induced multiple response of Artemia hemocytes

Polystyrene polymers cause severe toxicity to aquatic animals. However, the process and mechanisms of innate immunity of invertebrates living at the bottom of the food chain to these pollutants remain unclear. In this study, the blood system responses of zooplankton Artemia were assessed through in vivo and in vitro exposure to amino-modified polystyrene nanoplastics (PS-NH2 NPs). The results indicated that the LC50 values of PS-NH2 NPs were 1.09 μg·mL-1 over 48 h and 0.42 μg·mL-1 over 7 d. Based on the five hemocyte subpopulations identified in Artemia, in vitro exposure assays revealed that phagocytosis was performed by plasmocytes and granulocytes with phagocytic rate of 22.64 %. TEM analysis further showed that PS-NH2 NPs caused cytoplasm vacuolization, swollen mitochondria, and lipid processing disorder. Gene expression pattern results demonstrated that Spatzle, Tollip, Hsp70, Hsp90, Casp8, API5and Pxn were significantly upregulated upon acute and chronic exposure (p < 0.05), while chronic exposure could induce significantly upregulation of ProPO (p < 0.05). Moreover, PS-NH2 NPs exposure remarkably varied the hemolymph microbiota and hemogram, particularly by increasing the proportion of adipohemocytes and phagocytes (p < 0.05). Our findings suggest that PS-NH2 NPs induce different responses in Artemia hemocyte, as primarily reflected by phagocytic processes, expression of immune and apoptosis relating genes, cell fates, hemogram and hemolymph microbiota variations. These findings support the possibility of using Artemia hemocytes as bioindicator to estimate nanoplastics pollution, thus contributing to hematological toxicity research in response to nanoplastics.

Changes in the Aggregation Behaviour of Zinc Oxide Nanoparticles Influenced by Perfluorooctanoic Acid, Salts, and Humic Acid in Simulated Waters

The increasing utilization of zinc oxide nanoparticles (ZnO-NPs) in many consumer products is of concern due to their eventual release into the natural environment and induction of potentially adverse impacts. The behaviour and environmental impacts of ZnO-NPs could be altered through their interactions with environmentally coexisting substances. This study investigated the changes in the behaviour of ZnO-NPs in the presence of coexisting organic pollutants (such as perfluorooctanoic acid [PFOA]), natural organic substances (i.e., humic acid [HA]), and electrolytes (i.e., NaCl and CaCl2) in simulated waters. The size, shape, purity, crystallinity, and surface charge of the ZnO-NPs in simulated water after different interaction intervals (such as 1 day, 1 week, 2 weeks, and 3 weeks) at a controlled pH of 7 were examined using various characterization techniques. The results indicated alterations in the size (such as 162.4 nm, 1 day interaction to >10 µm, 3 weeks interaction) and zeta potential (such as -47.2 mV, 1 day interaction to -0.2 mV, 3 weeks interaction) of the ZnO-NPs alone and when PFOA, electrolytes, and HA were present in the suspension. Different influences on the size and surface charge of the nanoparticles were observed for fixed concentrations (5 mM) of the different electrolytes. The presence of HA-dispersed ZnO-NPs affected the zeta potential. Such dispersal effects were also observed in the presence of both PFOA and salts due to their large aliphatic carbon content and complex structure. Cation bridging effects, hydrophobic interactions, hydrogen bonding, electrostatic interactions, and van der Waals forces could be potential interaction forces responsible for the adsorption of PFOA. The presence of organic pollutants (PFOA) and natural organic substances (HA) can transform the surface characteristics and fate of ZnO-NPs in natural and sea waters.

An Outlook on Platinum-Based Active Ingredients for Dermatologic and Skincare Applications

Platinum-based materials exhibit a broad spectrum of biological activities, including antioxidant, anti-inflammatory, antimicrobial, and pro-collagen synthesis properties, making them particularly useful for various biomedical applications. This review summarizes the biological effects and therapeutic potential of platinum-based active ingredients in dermatological and skincare applications. We discuss their synthesis methods and their antioxidant, anti-inflammatory, antimicrobial, and collagen synthesis properties, which play essential roles in treating skin conditions including psoriasis and acne, as well as enhancing skin aesthetics in anti-aging products. Safety and sustainability concerns, including the need for green synthesis and comprehensive toxicological assessments to ensure safe topical applications, are also discussed. By providing an up-to-date overview of current research, we aim to highlight both the potential and the current challenges of platinum-based active ingredients in advancing dermatology and skincare solutions.

Use of nanotechnology-based nanomaterial as a substitute for antibiotics in monogastric animals

Nanotechnology has emerged as a promising solution for tackling antibiotic resistance in monogastric animals, providing innovative methods to enhance animal health and well-being. This review explores the novel use of nanotechnology-based nanomaterials as substitutes for antibiotics in monogastric animals. With growing global concerns about antibiotic resistance and the need for sustainable practices in animal husbandry, nanotechnology offers a compelling avenue to address these challenges. The objectives of this review are to find out the potential of nanomaterials in improving animal health while reducing reliance on conventional antibiotics. We examine various forms of nanomaterials and their roles in promoting gut health and also emphasize fresh perspectives brought by integrating nanotechnology into animal healthcare. Additionally, we delve into the mechanisms underlying the antibacterial properties of nanomaterials and their effectiveness in combating microbial resistance. By shedding light on the transformative role of nanotechnology in animal production systems. This review contributes to our understanding of how nanotechnology can provide safer and more sustainable alternatives to antibiotics.

Precisely Identifying the Sources of Magnetic Particles by Hierarchical Classification-Aided Isotopic Fingerprinting

Magnetic particles (MPs), with magnetite (Fe3O4) and maghemite (γ-Fe2O3) as the most abundant species, are ubiquitously present in the natural environment. MPs are among the most applied engineered particles and can be produced incidentally by various human activities. Identification of the sources of MPs is crucial for their risk assessment and regulation, which, however, is still an unsolved problem. Here, we report a novel approach, hierarchical classification-aided stable isotopic fingerprinting, to address this problem. We found that naturally occurring, incidental, and engineered MPs have distinct Fe and O isotopic fingerprints due to significant Fe/O isotope fractionation during their generation processes, which enables the establishment of an Fe-O isotopic library covering complex sources. Furthermore, we developed a three-level machine learning model that not only can distinguish the sources of MPs with a high precision (94.3%) but also can identify the multiple species (Fe3O4 or γ-Fe2O3) and synthetic routes of engineered MPs with a precision of 81.6%. This work represents the first reliable strategy for the precise source tracing of particles with multiple species and complex sources.

Toxicokinetics Explain Differential Freshwater Ecotoxicity of Nanoencapsulated Imidacloprid Compared to Its Conventional Active Ingredient

Agricultural applications of nanotechnologies necessitate addressing safety concerns associated with nanopesticides, yet research has not adequately elucidated potential environmental risks between nanopesticides and their conventional counterparts. To address this gap, we investigated the risk of nanopesticides by comparing the ecotoxicity of nanoencapsulated imidacloprid (nano-IMI) with its active ingredient to nontarget freshwater organisms (embryonic Danio rerio, Daphnia magna, and Chironomus kiinensis). Nano-IMI elicited approximately 5 times higher toxicity than IMI to zebrafish embryos with and without chorion, while no significant difference was observed between the two invertebrates. Toxicokinetics further explained the differential toxicity patterns of the two IMI analogues. One-compartmental two-phase toxicokinetic modeling showed that nano-IMI exhibited significantly slower elimination and subsequently higher bioaccumulation potential than IMI in zebrafish embryos (dechorinated), while no disparity in toxicokinetics was observed between nano-IMI and IMI in D. magna and C. kiinensis. A two-compartmental toxicokinetic model successfully simulated the slow elimination of IMI from C. kiinensis and confirmed that both analogues of IMI reached toxicologically relevant targets at similar levels. Although nanopesticides exhibit comparable or elevated toxicity, future work is of utmost importance to properly understand the life cycle risks from production to end-of-life exposures, which helps establish optimal management measures before their widespread applications.

Reproductive toxicity perspectives of nanoparticles: an update

INTRODUCTION

The rapid development of nanotechnologies with their widespread prosperities has advanced concerns regarding potential health hazards of the Nanoparticles.

RESULTS

Nanoparticles are currently present in several consumer products, including medications, food, textiles, sports equipment, and electrical components. Despite the advantages of Nanoparticles, their potential toxicity has negative impact on human health, particularly on reproductive health.

CONCLUSIONS

The impact of various NPs on reproductive system function is yet to be determined. Additional research is required to study the potential toxicity of various Nanoparticles on reproductive health. The primary objective of this review is to unravel the toxic effects of different Nanoparticles on the human reproductive functions and recent investigations on the reproductive toxicity of Nanoparticles both in vitro and in vivo.

Neurotoxicity of Some Environmental Pollutants to Zebrafish

The aquatic environment encompasses a wide variety of pollutants, from plastics to drug residues, pesticides, food compounds, and other food by-products, and improper disposal of waste is the main cause of the accumulation of toxic substances in water. Monitoring, assessing, and attempting to control the effects of contaminants in the aquatic environment are necessary and essential to protect the environment and thus human and animal health, and the study of aquatic ecotoxicology has become topical. In this respect, zebrafish are used as model organisms to study the bioaccumulation, toxicity, and influence of environmental pollutants due to their structural, functional, and material advantages. There are many similarities between the metabolism and physiological structures of zebrafish and humans, and the nervous system structure, blood-brain barrier function, and social behavior of zebrafish are characteristics that make them an ideal animal model for studying neurotoxicity. The aim of the study was to highlight the neurotoxicity of nanoplastics, microplastics, fipronil, deltamethrin, and rotenone and to highlight the main behavioral, histological, and oxidative status changes produced in zebrafish exposed to them.

Determination of metallic nanoparticles in soils by means spICP-MS after a microwave-assisted extraction treatment

Current sample preparation strategies for nanomaterials (NMs) analysis in soils by means single particle inductively coupled plasma mass spectrometry have significant constrains in terms of accuracy, sample throughput and applicability (i.e., type of NMs and soils). In this work, strengths and weakness of microwave assisted extraction (MAE) for NMs characterization in soils were systematically investigated. To this end, different extractants were tested (ultrapure water; NaOH, NH4OH, sodium citrate and tetrasodium pyrophosphate) and MAE operating conditions were optimized by means of design of experiments. Next, the developed method was applied to different type of metallic(oid) nanoparticles (Se-, Ag-, Pt- and AuNPs) and soils (alkaline, acid, sandy, clayey, SL36, loam ERMCC141; sludge amended ERM483). Results show that Pt- and AuNPs are preserved and quantitatively extracted from soils in 6 min (12 cycles of 30 s each) inside an 800 W oven by using 20 mL of 0.1 M NaOH solution. This methodology is applicable to soils showing a wide range of physicochemical properties except for clay rich samples. If clay soil fraction is significant (>15%), NMs are efficiently retained in the soil thus giving rise to poor recoveries (<10%). The analysis of labile NMs such as Se- and AgNPs is not feasible by means this approach since extraction conditions favors dissolution. Finally, when compared to current extraction methodologies (e.g., ultrasound, cloud point extraction, etc.), MAE affords better or equivalent accuracies and precision as well as higher sample throughput due to treatment speed and the possibility to work with several samples simultaneously.

Combined effects of pentachlorophenol and nano-TiO2 with different sizes on antioxidant, digestive, and immune responses of the swimming crab Portunus trituberculatus

Marine nano-titanium dioxide (nano-TiO2) and pentachlorophenol (PCP) pollution are escalating concerns in coastal areas. This study investigated the combined effects of continuous exposure to nano-TiO2 (25 nm, 100 nm) and PCP (0, 1, 10 μg/L) for 28 days on the antioxidant, digestive, and immune abilities of the swimming crab Portunus trituberculatus. Compared with the control group, the interaction between nano-TiO2 and PCP was significantly higher than exposure to a single stressor, with a pronounced decrease in amylase activity observed due to the reducing nano-TiO2 particle sizes. Resulting in increased MDA and SOD activity. The expression levels of Toll4, CSP3, and SER genes in crab hemolymph showed perturbations following exposure to nano-TiO2 and PCP. In summary, according to the results of CAT, GPX, PES and AMS enzyme activities, it was concluded that compared to the larger particle size (100 nm), the single stress of nano-TiO2 at a smaller particle size (25 nm) and co-stress with PCP have more significant impacts on P. trituberculatus. However, the potential physiological regulation mechanism of the interaction between these pollutants remains elusive and requires further study.

Mixture toxicity study of two metal oxide nanoparticles and chlorpyrifos on Eisenia andrei earthworms

Co-exposure soil studies of pollutants are necessary for an appropriate ecological risk assessment. Here, we examined the effects of two-component mixtures of metal oxide nanoparticles (ZnO NPs or goethite NPs) with the insecticide chlorpyrifos (CPF) under laboratory conditions in short-term artificial soil assays using Eisenia andrei earthworms. We characterized NPs and their mixtures by scanning electron microscopy, atomic force microscopy, dynamic light scattering and zeta potential, and evaluated effects on metal accumulation, oxidative stress enzymes, and neurotoxicity related biomarkers in single and combined toxicity assays. Exposure to ZnO NPs increased Zn levels compared to control in single and combined exposure (ZnO NPs + CPF) at 72 h and 7 days, respectively. In contrast, there was no indication of Fe increase in organisms exposed to goethite NPs. One of the most notable effects on oxidative stress biomarkers was produced by single exposure to goethite NPs, showing that the worms were more sensitive to goethite NPs than to ZnO NPs. Acetylcholinesterase and carboxylesterase activities indicated that ZnO NPs alone were not neurotoxic to earthworms, but similar degrees of inhibition were observed after single CPF and ZnO NPs + CPF exposure. Differences between single and combined exposure were found for catalase and superoxide dismutase (goethite NPs) and for glutathione S-transferase (ZnO NPs) activities, mostly at 72 h. These findings suggest a necessity to evaluate mixtures of NPs with co-existing contaminants in soil, and that the nature of metal oxide NPs and exposure time are relevant factors to be considered when assessing combined toxicity, as it may have an impact on ecotoxicological risk assessment.

Lipidomics Analysis Unravels Aberrant Lipid Species and Pathways Induced by Zinc Oxide Nanoparticles in Kidney Cells

Zinc oxide nanoparticles (ZnO NPs) are widely used in versatile applications, from high technology to household products. While numerous studies have examined the toxic gene profile of ZnO NPs across various tissues, the specific lipid species associated with adverse effects and potential biomarkers remain elusive. In this study, we conducted a liquid chromatography-mass spectrometry based lipidomics analysis to uncover potential lipid biomarkers in human kidney cells following treatment with ZnO NPs. Furthermore, we employed lipid pathway enrichment analysis (LIPEA) to elucidate altered lipid-related signaling pathways. Our results demonstrate that ZnO NPs induce cytotoxicity in renal epithelial cells and modulate lipid species; we identified 64 lipids with a fold change (FC) > 2 and p < 0.01 with corrected p < 0.05 in HK2 cells post-treatment with ZnO NPs. Notably, the altered lipids between control HK2 cells and those treated with ZnO NPs were associated with the sphingolipid, autophagy, and glycerophospholipid pathways. This study unveils novel potential lipid biomarkers of ZnO NP nanotoxicity, representing the first lipidomic profiling of ZnO NPs in human renal epithelial cells.

Applications of hollow nanostructures in water treatment considering organic, inorganic, and bacterial pollutants

One of the major issues of modern society is water contamination with different organic, inorganic, and contaminants bacteria. Finding cost-effective and efficient materials and methods for water treatment and environment remediation is among the scientists' most important considerations. Hollow-structured nanomaterials, including hollow fiber membranes, hollow spheres, hollow nanoboxes, etc., have shown an exciting capability for wastewater refinement approaches, including membrane technology, adsorption, and photocatalytic procedure due to their extremely high specific surface area, high porosity, unique morphology, and low density. Diverse hollow nanostructures could potentially eliminate organic contaminants, including dyes, antibiotics, oil/water emulsions, pesticides, and other phenolic compounds, inorganic pollutants, such as heavy metal ions, salts, phosphate, bromate, and other ions, and bacteria contaminations. Here, a comprehensive overview of hollow nanostructures' fabrication and modification, water contaminant classification, and recent studies in the water treatment field using hollow-structured nanomaterials with a comparative attitude have been provided, indicating the privilege abd detriments of this class of nanomaterials. Eventually, the future outlook of employing hollow nanomaterials in water refinery systems and the upcoming challenges arising in scaling up are also propounded.

The Impact of Nanomaterials on Photosynthesis and Antioxidant Mechanisms in Gramineae Plants: Research Progress and Future Prospects

As global food security faces challenges, enhancing crop yield and stress resistance becomes imperative. This study comprehensively explores the impact of nanomaterials (NMs) on Gramineae plants, with a focus on the effects of various types of nanoparticles, such as iron-based, titanium-containing, zinc, and copper nanoparticles, on plant photosynthesis, chlorophyll content, and antioxidant enzyme activity. We found that the effects of nanoparticles largely depend on their chemical properties, particle size, concentration, and the species and developmental stage of the plant. Under appropriate conditions, specific NMs can promote the root development of Gramineae plants, enhance photosynthesis, and increase chlorophyll content. Notably, iron-based and titanium-containing nanoparticles show significant effects in promoting chlorophyll synthesis and plant growth. However, the impact of nanoparticles on oxidative stress is complex. Under certain conditions, nanoparticles can enhance plants' antioxidant enzyme activity, improving their ability to withstand environmental stresses; excessive or inappropriate NMs may cause oxidative stress, affecting plant growth and development. Copper nanoparticles, in particular, exhibit this dual nature, being beneficial at low concentrations but potentially harmful at high concentrations. This study provides a theoretical basis for the future development of nanofertilizers aimed at precisely targeting Gramineae plants to enhance their antioxidant stress capacity and improve photosynthesis efficiency. We emphasize the importance of balancing the agricultural advantages of nanotechnology with environmental safety in practical applications. Future research should focus on a deeper understanding of the interaction mechanisms between more NMs and plants and explore strategies to reduce potential environmental impacts to ensure the health and sustainability of the ecosystem while enhancing the yield and quality of Gramineae crops.

The distribution, fate, and environmental impacts of food additive nanomaterials in soil and aquatic ecosystems

Nanomaterials in the food industry are used as food additives, and the main function of these food additives is to improve food qualities including texture, flavor, color, consistency, preservation, and nutrient bioavailability. This review aims to provide an overview of the distribution, fate, and environmental and health impacts of food additive nanomaterials in soil and aquatic ecosystems. Some of the major nanomaterials in food additives include titanium dioxide, silver, gold, silicon dioxide, iron oxide, and zinc oxide. Ingestion of food products containing food additive nanomaterials via dietary intake is considered to be one of the major pathways of human exposure to nanomaterials. Food additive nanomaterials reach the terrestrial and aquatic environments directly through the disposal of food wastes in landfills and the application of food waste-derived soil amendments. A significant amount of ingested food additive nanomaterials (> 90 %) is excreted, and these nanomaterials are not efficiently removed in the wastewater system, thereby reaching the environment indirectly through the disposal of recycled water and sewage sludge in agricultural land. Food additive nanomaterials undergo various transformation and reaction processes, such as adsorption, aggregation-sedimentation, desorption, degradation, dissolution, and bio-mediated reactions in the environment. These processes significantly impact the transport and bioavailability of nanomaterials as well as their behaviour and fate in the environment. These nanomaterials are toxic to soil and aquatic organisms, and reach the food chain through plant uptake and animal transfer. The environmental and health risks of food additive nanomaterials can be overcome by eliminating their emission through recycled water and sewage sludge.

A critical review on fate, behavior, and ecotoxicological impact of zinc oxide nanoparticles on algae

The rapid inclusion of zinc oxide nanoparticles (ZnO NPs) in nanotechnology-based products over the last decade has generated a new threat in the apprehension of the environment. The massive use of zinc nanosized products will certainly be disposed of and be released, eventually entering the aquatic ecosystem, posing severe environmental hazards. Moreover, nanosized ZnO particles owing the larger surface area per volume exhibit different chemical interactions within the aquatic ecosystem. They undergo diverse potential transformations because of their unique physiochemical properties and the feature of receiving medium. Therefore, assessment of their impact is critical not only for scavenging the present situation but also for preventing unintended environmental hazards. Algae being a primary producer of the aquatic ecosystem help assess the risk of massive NPs usage in environmental health. Because of their nutritional needs and position at the base of aquatic food webs, algal indicators exhibit relatively unique information concerning ecosystem conditions. Moreover, algae are presently the most vital part of the circular economy. Hence, it is imperative to understand the physiologic, metabolic, and morphologic changes brought by the ZnO NPs to the algal cells along with the development of the mechanism imparting toxicity mechanism. We also need to develop an appropriate scientific strategy in the innovation process to restrain the exposure of NPs at safer levels. This review provides the details of ZnO NP interaction with algae. Moreover, their impact, mechanism, and factors affecting toxicity to the algae are discussed.

Determination of oxidative stress responses caused by aluminum oxide (γ-Al2O3 and α-Al2O3) nanoparticles in Gammarus pulex

The rapid growth in the use of aluminum oxide nanoparticles (Al2O3 NPs) in various fields such as medicine, pharmacy, cosmetics industries and engineering, and the fact that these NPs and their wastes mix with the aquatic environment and damage the aquatic ecosystem, affect the organisms in the water, enter the food chain and reach humans is a major problem is cause for concern. The aim of this study is to investigate the oxidative stress caused by two separate forms of aluminum oxide, γ-Al2O3 and α-Al2O3, in Gammarus pulex, which is a good indicator species, with biochemical parameters. For this purpose, G. pulex was exposed to different concentrations (0, 10, 20, 40 ppm) of γ-Al2O3 and α-Al2O3 separately. The experiments were carried out for 24 and 96 h by creating 3 repeated experimental groups consisting of 4 groups. For biomarker analysis, superoxide dismutase (SOD), catalase (CAT) activities and glutathione (GSH) and thiobarbituric acid (TBARS) levels were performed using an ELISA kit. As a result of the in experimental study, it was observed that both nanoparticles affected oxidative stress and antioxidant parameters after 96 h compared to the control group. Increases in SOD activity were observed, γ-Al2O3 caused a decrease in CAT activity at 24 h, and α- Al2O3 caused increases in CAT activity at 96 h. Decreases in GSH levels and increases in TBARS levels have been observed.

Carbon nanotubes and nanofibers seen as emerging threat to fish: Historical review and trends

Since the discovery of the third allotropic carbon form, carbon-based one-dimensional nanomaterials (1D-CNMs) became an attractive and new technology with different applications that range from electronics to biomedical and environmental technologies. Despite their broad application, data on environmental risks remain limited. Fish are widely used in ecotoxicological studies and biomonitoring programs. Thus, the aim of the current study was to summarize and critically analyze the literature focused on investigating the bioaccumulation and ecotoxicological impacts of 1D-CNMs (carbon nanotubes and nanofibers) on different fish species. In total, 93 articles were summarized and analyzed by taking into consideration the following aspects: bioaccumulation, trophic transfer, genotoxicity, mutagenicity, organ-specific toxicity, oxidative stress, neurotoxicity and behavioral changes. Results have evidenced that the analyzed studies were mainly carried out with multi-walled carbon nanotubes, which were followed by single-walled nanotubes and nanofibers. Zebrafish (Danio rerio) was the main fish species used as model system. CNMs' ecotoxicity in fish depends on their physicochemical features, functionalization, experimental design (e.g. exposure time, concentration, exposure type), as well as on fish species and developmental stage. CNMs' action mechanism and toxicity in fish are associated with oxidative stress, genotoxicity, hepatotoxicity and cardiotoxicity. Overall, fish are a suitable model system to assess the ecotoxicity of, and the environmental risk posed by, CNMs.

Cotransport of fullerene nanoparticles and montmorillonite colloids in porous media: Critical role of divalent cations of montmorillonite

While the cotransport of carbon nanoparticles (CNPs) and clay colloids in porous media has been widely studied, the influence of the cation exchange capacity (CEC) of clay colloids on the transport process remains unclear. In this study, batch adsorption and column transport experiments were conducted to investigate the fate and transport of CNPs and clay colloids in quartz sand, with respect to the effect of monovalent-cation exchange capacity (mono-CEC), divalent-cation exchange capacity (di-CEC) and total CEC of clays. Fullerene nanoparticles (nC60) and six types of montmorillonite (ML) with different CEC were selected as modeled CNPs and clay colloids, respectively. Transport behavior of nC60 and ML was characterized using breakthrough curves (BTCs) and fitted with two-kinetic-sites colloid transport model. Results of the adsorption experiments showed a good linear correlation between the deposition of nC60 on the sand surface and the di-CEC of ML. Transport of ML and nC60 was inhibited by each other. The calculated mass recovery of nC60, as well as the fitted maximum deposition capacity and attachment rate coefficients of nC60 exhibited a strong linear relationship with the di-CEC of ML. These results indicate that divalent cations in ML interlayers play a significant role in aggregation between nC60 and ML and their cotransport. Through measurements of the particle size and zeta potentials of sole nC60 and mixtures of ML and nC60, FTIR and XPS analysis of nC60 under different conditions, and a release experiment of nC60 in a sand column, it demonstrated cation bridging (Ca2+-π) between nC60 and ML mediated by the divalent cations in ML interlayers. The study highlighted the potential of using di-CEC of clays as an indicator to predict the mobility of nC60 in clay-containing porous media and added insights to the transport behavior of CNPs in porous media.

Surface functional groups on nanoplastics delay the recovery of gut microbiota after combined exposure to sulfamethazine in marine medaka (Oryzias melastigma)

Nanoplastics can interact with antibiotics, altering their bioavailability and the ensuing toxicity in marine organisms. It is reported that plain polystyrene (PS) nanoplastics decrease the bioavailability and adverse effects of sulfamethazine (SMZ) on the gut microbiota in Oryzias melastigma. However, the influence of surface functional groups on the combined effects with SMZ remains largely unknown. In this study, adult O. melastigma were fed diet amended with 4.62 mg/g SMZ and 3.65 mg/g nanoplastics (i.e., plain PS, PS-COOH and PS-NH2) for 30 days (F0-E), followed by a depuration period of 21 days (F0-D). In addition, the eggs produced on the last day of exposure were cultured under standard protocols without further exposure for 2 months (F1 fish). The results showed that the alpha diversity or the bacterial community of gut microbiota did not differ among the SMZ + PS, SMZ + PS-COOH, and SMZ + PS-NH2 groups in the F0-E and F1 fish. Interestingly, during the depuration, a clear recovery of gut microbiota (e.g., increases in the alpha diversity, beneficial bacteria abundances and network complexity) was found in the SMZ + PS group, but not for the SMZ + PS-COOH and SMZ + PS-NH2 groups, indicating that PS-COOH and PS-NH2 could prolong the toxic effect of SMZ and hinder the recovery of gut microbiota. Compared to plain PS, lower egestion rates of PS-COOH and PS-NH2 were observed in O. melastigma. In addition, under the simulated fish digest conditions, the SMZ-loaded PS-NH2 was found to desorb more SMZ than the loaded PS and PS-COOH. These results suggested that the surface -COOH and -NH2 groups on PS could influence their egestion efficiency and the adsorption/desorption behavior with SMZ, resulting in a long-lasting SMZ stress in the gut during the depuration phase. Our findings highlight the complexity of the carrier effect and ecological risk of surface-charged nanoplastics and the interactions between nanoplastics and antibiotics in natural environments.

Indirect effects of interference of two emerging environmental contaminants on cell health: Radiofrequency radiation and gold nanoparticles

BACKGROUND

The global need for wireless technologies is growing rapidly. So, we have been exposed to a new type of environmental pollution: radiofrequency radiation (RFR). Recent studies have shown that RFR can cause not only direct effects but also indirect or non-targeted effects such as the bystander effect (BE). In this study, we investigated the BE induced by RFR in the present of gold nanoparticles (GNP). Moreover, we studied the expression of cyclooxygenase-2 (COX-2).

METHODS

Non-toxic dose of 15-nm GNP was used to treat the Chinese Hamster Ovary (CHO) cells. After 48 h of incubation, cells were exposed to 900 MHz GSM RFR for 24 h. Then we collected the cell culture medium of these cells (conditioned culture medium, CCM) and transferred it to new cells (bystander cells). Cell deaths, DNA breaks, oxidative stress and COX-2 expression were analyzed in all groups.

RESULTS

The results showed that RFR increased metabolic death in cells treated with GNP. Inversely, the colony formation ability was reduced in bystander cells and RFR exposed cells either in the presence or absence of GNP. Also, the level of reactive oxygen species (ROS) in GNP treated cells showed a significant reduction compared to those of untreated cells. However, RFR-induced DNA breaks and the frequencies of micronuclei (MN) were not significantly affected by GNP. The expression of COX-2 mRNA increased in RFR GNP treated cells, but the difference was not significant.

CONCLUSION

Our results for the first time indicated that RFR induce indirect effects in the presence of GNP. However, the molecular mediators of these effects differ from those in the absence of GNP. Also, to our knowledge, this is the first study to show that COX-2 is not involved in the bystander effect induced by 900 MHz RFR.

From lab to ecosystem: Understanding the ecological footprints of engineered nanoparticles

Nanotechnology has attained significant attention from researchers in past decades due to its numerous advantages, such as biocompatibility, biodegradability, and improved stability over conventional drug delivery systems. The fabrication of engineered nanoparticles (ENPs), including carbon nanotubes (CNTs), fullerenes, metallic and metal oxide-based NPs, has been steadily increasing day due to their wide range of applications from household to industrial applications. Fabricated ENPs can release different materials into the environment during their fabrication process. The effect of such materials on the environment is the primary concern with due diligence on the safety and efficacy of prepared NPs. In addition, an understanding of chemistry, reactivity, fabrication process, and viable mechanism of NPs involved in the interaction with the environment is very important. To date, only a limited number of techniques are available to assess ENPs in the natural environment which makes it difficult to ascertain the impact of ENPs in natural settings. This review extensively examines the environmental effects of ENPs and briefly discusses useful tools for determining NP size, surface charge, surface area, and external appearance. In conclusion, the review highlights the potential risks associated with ENPs and suggests possible solutions.

Predicting environmental concentrations of nanomaterials for exposure assessment - a review

There have been major advances in the science to predict the likely environmental concentrations of nanomaterials, which is a key component of exposure and subsequent risk assessment. Considerable progress has been since the first Material Flow Analyses (MFAs) in 2008, which were based on very limited information, to more refined current tools that take into account engineered nanoparticle (ENP) size distribution, form, dynamic release, and better-informed release factors. These MFAs provide input for all environmental fate models (EFMs), that generate estimates of particle flows and concentrations in various environmental compartments. While MFA models provide valuable information on the magnitude of ENP release, they do not account for fate processes, such as homo- and heteroaggregation, transformations, dissolution, or corona formation. EFMs account for these processes in differing degrees. EFMs can be divided into multimedia compartment models (e.g., atmosphere, waterbodies and their sediments, soils in various landuses), of which there are currently a handful with varying degrees of complexity and process representation, and spatially-resolved watershed models which focus on the water and sediment compartments. Multimedia models have particular applications for considering predicted environmental concentrations (PECs) in particular regions, or for developing generic "fate factors" (i.e., overall persistence in a given compartment) for life-cycle assessment. Watershed models can track transport and eventual fate of emissions into a flowing river, from multiple sources along the waterway course, providing spatially and temporally resolved PECs. Both types of EFMs can be run with either continuous sources of emissions and environmental conditions, or with dynamic emissions (e.g., temporally varying for example as a new nanomaterial is introduced to the market, or with seasonal applications), to better understand the situations that may lead to peak PECs that are more likely to result in exceedance of a toxicological threshold. In addition, bioaccumulation models have been developed to predict the internal concentrations that may accumulate in exposed organisms, based on the PECs from EFMs. The main challenge for MFA and EFMs is a full validation against observed data. To date there have been no field studies that can provide the kind of dataset(s) needed for a true validation of the PECs. While EFMs have been evaluated against a few observations in a small number of locations, with results that indicate they are in the right order of magnitude, there is a great need for field data. Another major challenge is the input data for the MFAs, which depend on market data to estimate the production of ENPs. The current information has major gaps and large uncertainties. There is also a lack of robust analytical techniques for quantifying ENP properties in complex matrices; machine learning may be able to fill this gap. Nevertheless, there has been major progress in the tools for generating PECs. With the emergence of nano- and microplastics as a leading environmental concern, some EFMs have been adapted to these materials. However, caution is needed, since most nano- and microplastics are not engineered, therefore their characteristics are difficult to generalize, and there are new fate and transport processes to consider.

Cell size-dependent species sensitivity to nanoparticles underlies changes in phytoplankton diversity and productivity

Nanoparticle pollution has been shown to affect various organisms. However, the effects of nanoparticles on species interactions, and the role of species traits, such as body size, in modulating these effects, are not well-understood. We addressed this issue using competing freshwater phytoplankton species exposed to copper oxide nanoparticles. Increasing nanoparticle concentration resulted in decreased phytoplankton species growth rates and community productivity (both abundance and biomass). Importantly, we consistently found that nanoparticles had greater negative effects on species with smaller cell sizes, such that nanoparticle pollution weakened the competitive dominance of smaller species and promoted species diversity. Moreover, nanoparticles reduced the growth rate differences and competitive ability differences of competing species, while having little effect on species niche differences. Consequently, nanoparticle pollution reduced the selection effect on phytoplankton community abundance, but increased the selection effect on community biomass. Our results suggest cell size as a key functional trait to consider when predicting phytoplankton community structure and ecosystem functioning in the face of increasing nanopollution.

Nonmonotonic electrophoretic mobility of rodlike polyelectrolytes by multivalent coions in added salt

It is well established that when multivalent counterions or salts are added to a solution of highly charged polyelectrolytes (PEs), correlation effects can cause charge inversion of the PE, leading to electrophoretic mobility (EM) reversal. In this work, we use coarse-grained molecular-dynamics simulations to unravel the less understood effect of coion valency on EM reversal for rigid DNA-like PEs. We find that EM reversal induced by multivalent counterions is suppressed with increasing coion valency in the salt added and eventually vanishes. Further, we find that EM is enhanced at fixed low salt concentrations for salts with monovalent counterions when multivalent coions with increasing valency are introduced. However, increasing the salt concentration causes a crossover that leads to EM reversal which is enhanced by increasing coion valency at high salt concentration. Remarkably, this multivalent coion-induced EM reversal persists even for low values of PE linear charge densities where multivalent counterions alone cannot induce EM reversal. These results facilitate tuning PE-PE interactions and self-assembly with both coion and counterion valencies.

Toxic and bioaccumulative effects of zinc nanoparticle exposure to goldfish, Carassius auratus (Linnaeus, 1758)

The widespread use of produced metal oxide nanoparticles (NPs) has increased major concerns about their impact on human as well as aquatic animal health. The present study shows that exposure to different concentrations of zinc oxide (ZnO) NPs led to high accumulations of Zn ions in the metabolic organs of fish (liver and gills), resulting in severe oxidative stress in Carassius auratus. The goldfish (C. auratus) was chosen as an aquatic species for the evaluation of the potential toxicity of aqueous ZnO-NPs (Treatments of hemoglobin and neutrophils (0, 0.5, 1, and 1.5 mg L- 1) following 14 days of exposure. A range of histological and hematological factors were examined. Exposure to the NPs produced significant reduction of red blood cell and white blood cell counts, hematocrit) were found to produce no significant differences in lymphocyte, monocyte, and eosinophil counts; as well as the mean corpuscular hemoglobin concentrations index (P > 0.05). Moreover, the results revealed significant alterations in serum biochemical parameters, hepatic enzyme levels, and immune and antioxidant responses; except for total protein and superoxide dismutase (SOD) of C. auratus exposed to ZnO-NPs, particularly at the 1 and 1.5 mg L- 1 concentrations. Fish exposed to 1 and 1.5 mg L-1 ZnO-NPs displayed a significant reduction in alternative complement pathway activity, lysozyme, and total protein contents of mucus compared to those in the control group. The results showed that hepatic SOD and catalase, and gill catalase activity were significantly decreased, and their malondialdehyde levels increased at 1 and 1.5 mg L-1 ZnO-NPs compared to the control group (P < 0.05). Significant accumulations of ZnO-NPs were observed in the liver, kidney, and gill tissues of fish leading to severe histopathological alterations in these organs. These results suggest that water-borne ZnO-NPs can easily accumulate in metabolic organs and lead to oxidative stress and destructive effects on the physiological features of C. auratus.

Environmental effects and interaction of nanoparticles on beneficial soil and aquatic microorganisms

A steadily increasing production volume of nanoparticles reflects their numerous industrial and domestic applications. These economic successes come with the potential adverse effects on natural systems that are associated with their presence in the environment. Biological activities and effects of nanoparticles are affected by their entry method together with their specificities like their size, shape, charge, area, and chemical composition. Particles can be classified as safe or dangerous depending on their specific properties. As both aquatic and terrestrial systems suffer from organic and inorganic contamination, nanoparticles remain a sink for these contaminants. Researching the sources, synthesis, fate, and toxicity of nanoparticles has advanced significantly during the last ten years. We summarise nanoparticle pathways throughout the ecosystem and their interactions with beneficial microorganisms in this research. The prevalence of nanoparticles in the ecosystem causes beneficial microorganisms to become hazardous to their cells, which prevents the synthesis of bioactive molecules from undergoing molecular modifications and diminishes the microbe population. Recently, observed concentrations in the field could support predictions of ambient concentrations based on modeling methodologies. The aim is to illustrate the beneficial and negative effects that nanoparticles have on aqueous and terrestrial ecosystems, as well as the methods utilized to reduce their toxicity.

Insight interactions of engineered nanoparticles with aquatic higher plants for phytoaccumulation, phytotoxicity, and phytoremediation applications: A review

With the growing age of human civilization, industrialization has paced up equally which is followed by the innovation of newer concepts of science and technology. One such example is the invention of engineered nanoparticles and their flagrant use in widespread applications. While ENPs serve their intended purposes, they also disrupt the ecological balance by contaminating pristine aquatic ecosystems. This review encompasses a comprehensive discussion about the potent toxicity of ENPs on aquatic ecosystems, with a particular focus on their impact on aquatic higher plants. The discussion extends to elucidating the fate of ENPs upon release into aquatic environments, covering aspects ranging from morphological and physiological effects to molecular-level phytotoxicity. Furthermore, this level of toxicity has been correlated with the determination of competent plants for the phytoremediation process towards the mitigation of this ecological stress. However, this review further illustrates the path of future research which is yet to be explored. Determination of the genotoxicity level of aquatic higher plants could explain the entire process comprehensively. Moreover, to make it suitable to be used in natural ecosystems phytoremediation potential of co-existing plant species along with the presence of different ENPs need to be evaluated. This literature will undoubtedly offer readers a comprehensive understanding of the stress induced by the irresponsible release of engineered nanoparticles (ENP) into aquatic environments, along with insights into the resilience characteristics of these pristine ecosystems.

Elucidating growth and biochemical characteristics of rice seedlings under stress from chromium VI salt and nanoparticles

Plants are usually provoked by a variety of heavy metal (HM) stressors that have adverse effects on their growth and other biochemical characterizations. Among the HMs, chromium has been considered the most toxic for both plants and animals. The present study was conducted to compare the phytotoxic effects of increasing chromium (VI) salt and nanoparticles (NPs) concentrations on various growth indexes of rice (Oryza sativa L. var. swat 1) seedlings grown in a hydroponic system. The 7-day rice seedlings were exposed to Cr (VI) salt and NPs hydroponic suspensions which were adjusted to the concentration of 0, 50, 100, 150, 200 and 250 mg/L. Both the Cr (VI) salt and NPs with lower concentrations (up to 100mg/L) exerted minimum inhibitory effects on the growth performance of rice seedlings. However, a significant decrease in shoot and root length and their fresh and dry weight was recorded at higher doses of Cr (VI) salt (200 mg/L) and NPs (250 mg/L). The stress induced by Cr (VI) salt has drastically affected the roots, whereas, Cr (VI) NPs significantly affected the shoot tissues. Photosynthetic pigments decreased significantly in a dose-dependent manner, and the reduction was more pronounced in rice seedlings exposed to Cr (VI) NPs compared to Cr (VI) salt. Cr (VI) NPs enhanced the membrane permeability in shoots and roots as compared to that of Cr (VI) salt, which resulted in higher concentration of reactive oxygen species (ROS) and increased lipid peroxidation. The activities of antioxidant enzymes superoxide dismutase (SOD), peroxidase (POD), catalase (CAT) and ascorbate peroxidase (APX) increased significantly in shoot/root tissue following exposure to higher doses of Cr (VI) salt (200 mg/L) and NPs stress (250 mg/L), while minor changes in CAT and APX activities were observed in root and shoot tissues after exposure to higher concentration of Cr (VI) NP. Furthermore, the increasing concentrations of Cr (VI) NPs increased the length of stomatal guard cells. Conclusively, Cr (VI) salt and NPs in higher concentrations have higher potential to damage the growth and induce oxidative stress in rice plants.

Assessment of Genotoxicity of Zinc Oxide Nanoparticles Using Mosquito as Test Model

The widespread applications of ZnO NPs in the different areas of science, technology, medicine, agriculture, and commercial products have led to increased chances of their release into the environment. This created a growing public concern about the toxicological and environmental effects of the nanoparticles. The impact of these NPs on the genetic materials of living organisms is documented in some cultured cells and plants, but there are only a few studies regarding this aspect in animals. In view of this, the present work regarding the assessment of the genotoxicity of zinc oxide nanoparticles using the mosquito Culex quinquefaciatus has been taken up. Statistically significant chromosomal aberrations over the control are recorded after the exposure of the fourth instar larvae to a dose of less than LD20 for 24 h. In order to select this dose, LD20 of ZnO NPs for the mosquito is determined by Probit analysis. Lacto-aceto-orcein stained chromosomal preparations are made from gonads of adult treated and control mosquitoes. Both structural aberrations, such as chromosomal breaks, fragments, translocations, and terminal fusions, resulting in the formation of rings and clumped chromosomes, and numerical ones, including hypo- and hyper-aneuploidy at metaphases, bridges, and laggards at the anaphase stage are observed. The percentage frequency of abnormalities in the shape of sperm heads is also found to be statistically significant over the controls. Besides this, zinc oxide nanoparticles are also found to affect the reproductive potential and embryo development as egg rafts obtained from the genetic crosses of ZnO nanoparticle-treated virgin females and normal males are small in size with a far smaller number of eggs per raft. The percentage frequencies of dominant lethal mutations indicated by the frequency of unhatched eggs are also statistically significant (p < 0.05) over the control. The induction of abnormalities in all of the three short-term assays studied during the present piece of work indicates the genotoxic potential of ZnO NPs, which cannot be labeled absolutely safe, and this study pinpoints the need to develop strategies for the protection of the environment and living organisms thriving in it.

Retention and release of black phosphorus nanoparticles in porous media under various physicochemical conditions

Black phosphorus nanosheets/nanoparticles (BPNs) are widely applied in many fields. However, the transport of BPNs in the subsurface still has not yet been reported and there is increasing concern about potential adverse impacts on ecosystems. Roles of median grain size and surface roughness, BPN concentration, and solution chemistries (pH, ionic strength, and cation types) on the retention and release of BPNs in column experiments were therefore investigated. The mobility of BPNs significantly increased with increasing grain size and decreasing surface roughness due to their influence on the mass transfer rate, number of deposition sites and retention capacity, and straining processes. Transport of BPNs was enhanced with an increase in pH and a decrease in ionic strength because of surface deprotonation and stronger repulsion that tends to reduce aggregation. The BPN transport was significantly sensitive to ionic strength, compared with other engineered nanoparticles. Additionally, charge heterogeneity and cation-bridging played a critical role in the retention of BPNs in the presence of divalent cations. Higher input concentrations increased the retention of BPNs, probably because collisions, aggregation at pore throat locations, and hydrodynamic bridging were more pronounced. Small fractions of BPNs can be released under decreasing IS and increasing pH due to the expansion of the electrical double layer and increased repulsion at convex roughness locations. A mathematical model that includes provisions for advective dispersive transport and time-dependent retention with blocking or ripening terms well described the retention and release of BPNs. These findings provide fundamental information that helps to understand the transport of BPNs in the subsurface environments.

Isolation of Carbon Black from Soils by Dispersion for Analysis: Quantitation and Characterization by Field Flow Fractionation Techniques

In the present work, a procedure based on a dispersive medium for carbon black (CB) isolation from soil samples for analysis was proposed for the first time. Polymeric and biological dispersants and a sequential use of both dispersants were assayed. Asymmetrical flow field flow fractionation with dynamic light scattering detector (AF4-DLS) and sedimentation field flow fractionation with multi-angle light scattering detector (SdF3-MALS) were used for CB quantitation and characterization in the achieved dispersions. Soil samples contaminated with CB were processed, and CB isolation depended on the solid size distribution and composition and dispersant nature. More quantitative isolations were achieved for the four soils treated by the biological dispersant. As the organic matter percentage is higher in soil, the CB isolation was better, varying between 75 and 99% with standard deviation (s) ⩽ 2% for all soils. A soil contaminated with a CB-based pigment paste was analyzed, achieving (99 ± 2)% expressed as expanded uncertainty (K = 2) of dispersive isolation by the biological dispersant, and the sampling was scaled to 250 g of soil with positive results. The procedure was completed by CB recovery to obtain a solid residue able to be reused if necessary. For the filter-aided recovery step, different membranes (fiberglass, nylon, and Teflon) with a pore size between 0.1 and 5 μm were tested. The quantitation of the CB retained in the filter was measured by diffuse reflectance spectroscopy. Teflon (0.10 μm) provided better results for CB recovery, and its re-dispersion was also studied with suitable results. Determination of CB from the filters by diffuse reflectance spectrometry provided the same results than AF4 for CB dispersions.

A critical review on nanoplastics and its future perspectives in the marine environment

Nanoplastics (plastic particles smaller than 1 μm) are the least-known type of marine litter. Nanoplastics (NPs) have attracted much interest in recent years because of their prevalence in the environment and the potential harm they can cause to living organisms. This article focuses on understanding NPs and their fate in the marine environment. Sources of NPs have been identified, including accidental release from products or through nano-fragmentation of larger plastic debris. As NPs have a high surface area, they may retain harmful compounds. The presence of harmful additives in NPs poses unique practical challenges for studies on their toxicity. In this review, several methods specifically adapted for the physical and chemical characterization of NPs have been discussed. Furthermore, the review provides an overview of the translocation and absorption of NPs into organisms, along with an evaluation of the release of potential toxins from NPs. Further, we have provided an overview about the existing methods suggested for the possible degradation of these NPs. We conclude that the hazards of NPs are plausible but unknown, necessitating a thorough examination of NPs' sources, fate, and effects to better mitigate and spread awareness about this emerging contaminant.

How could actinobacteria augment the growth and redox homeostasis in barley plants grown in TiO2NPs-contaminated soils? A growth and biochemical study

The increases in titanium dioxide nanoparticles (TiO2-NPs) released into the environment have raised concerns about their toxicity. However, their phytotoxic impact on plants is not well studied. Therefore, this study aimed at a deeper understanding of the TiO2-NPs phytotoxic impact on barley (Hordeum vulgare) growth and stress defense. We also hypothesized that soil inoculation with bioactive Rhodospirillum sp. JY3 strain can be applied as a biological fertilizer to alleviate TiO2-NPs phytotoxicity. At TiO2-NPs phytotoxicity level, photosynthesis was significantly retarded (∼50% reduction) in TiO2-NPs treated-barley plants which accordingly affect the biomass of barley plants. This retardation was accompanied by a remarkable induction of oxidative damage (H2O2, lipid peroxidation) with a concomitant reduction in the antioxidant defense metabolism. At a glance, Rhodospirillum sp. JY3 ameliorated the reduction in growth by enhancing the photosynthetic efficiency in contaminated barley plants. Moreover, Rhodospirillum sp. JY3 inoculation reduced the oxidative damage induced by TiO2-NPs via quenching H2O2 production and lipid peroxidation. Regarding the antioxidant defense arsenal, Rhodospirillum sp. JY3 enhanced both enzymatic (e.g. peroxidase (POX), catalase (CAT), superoxide dismutase (SOD), …. etc.) and non-enzymatic (glutathione (GSH), ascorbate (ASC), polyphenols, flavonoids, tocopherols) antioxidants in shoots and to a greater extent roots of barley plants. Moreover, the inoculation significantly enhanced the heavy metal-detoxifying metabolites (eg. phytochelatins, glutaredoxin, thioredoxin, peroxiredoxin) as well as metal-detoxifying enzymes in barley shoots and more apparently in roots of TiO2-NPs stressed plants. Furthermore, there was an organ-specific response to TiO2-NPs and Rhodospirillum sp. JY3. To this end, this study shed light, for the first time, on the molecular bases underlie TiO2-NPs stress mitigating impact of Rhodospirillum sp. JY3 and it introduced Rhodospirillum sp. JY3 as a promising eco-friendly tool in managing environmental risks to maintain agricultural sustainability.

Effects of Zinc Oxide Nanoparticle Exposure on Human Glial Cells and Zebrafish Embryos

Zinc oxide nanoparticles (ZnO NPs) are among the most widely used nanomaterials. They have multiple applications in cosmetics, textiles, paints, electronics and, recently, also in biomedicine. This extensive use of ZnO NPs notably increases the probability that both humans and wildlife are subjected to undesirable effects. Despite being among the most studied NPs from a toxicological point of view, much remains unknown about their ecotoxicological effects or how they may affect specific cell types, such as cells of the central nervous system. The main objective of this work was to investigate the effects of ZnO NPs on human glial cells and zebrafish embryo development and to explore the role of the released Zn2+ ions in these effects. The effects on cell viability on human A172 glial cells were assessed with an MTT assay and morphological analysis. The potential acute and developmental toxicity was assessed employing zebrafish (Danio rerio) embryos. To determine the role of Zn2+ ions in the in vitro and in vivo observed effects, we measured their release from ZnO NPs with flame atomic absorption spectrometry. Then, cells and zebrafish embryos were treated with a water-soluble salt (zinc sulfate) at concentrations that equal the number of Zn2+ ions released by the tested concentrations of ZnO NPs. Exposure to ZnO NPs induced morphological alterations and a significant decrease in cell viability depending on the concentration and duration of treatment, even after removing the overestimation due to NP interference. Although there were no signs of acute toxicity in zebrafish embryos, a decrease in hatching was detected after exposure to the highest ZnO NP concentrations tested. The ability of ZnO NPs to release Zn2+ ions into the medium in a concentration-dependent manner was confirmed. Zn2+ ions did not seem entirely responsible for the effects observed in the glial cells, but they were likely responsible for the decrease in zebrafish hatching rate. The results obtained in this work contribute to the knowledge of the toxicological potential of ZnO NPs.

Leaf chlorophyll fluorescence and reflectance of oakleaf lettuce exposed to metal and metal(oid) oxide nanoparticles

BACKGROUND

Most nanoparticles (NPs) have a significant impact on the structure and function of the plant photosynthetic apparatus. However, their spectrum of action varies significantly, from beneficial stimulation to toxicity, depending on the type of NPs, the concentration used and plant genotypic diversity. Photosynthetic performance can be assessed through chlorophyll a fluorescence (ChlF) measurements. These data allow to indirectly obtain detailed information about primary light reactions, thylakoid electron transport reactions, dark enzymatic stroma reactions, slow regulatory processes, processes at the pigment level. It makes possible, together with leaf reflectance performance, to evaluate photosynthesis sensitivity to stress stimuli.

RESULTS

We investigated effects of different metal and metal(oid) oxide nanoparticles on photosynthesis of oakleaf lettuce seedlings by monitoring the chlorophyll a fluorescence light radiation and reflectance from the leaves. Observations of ChlF parameters and changes in leaf morphology were carried out for 9 days in two-day intervals. Spectrophotometric studies were performed at 9th day. Suspensions of NPs with the following concentrations were used: 6% TiO2, SiO2; 3% CeO2, SnO2, Fe2O3; 0.004% (40 ppm) Ag; 0.002% (20 ppm) Au. Nanoparticles were applied directly on the leaves which caused small symptoms of chlorosis, necrosis and leaf veins deformation, but the plants fully recovered to the initial morphological state at 9th day. Leaf reflectance analysis showed an increase in FRI for SiO2-NPs and CeO2-NPs treatments and ARI2 for Fe2O3, however, WBI and PRI coefficients for the latter nanoparticle were lower than in control. Chlorophyll a fluorescence parameters have changed due to NPs treatment. Fe2O3-NPs caused an increase in Fv/F0, PIABS, ET0/RC, DI0/RC, ABS/RC in different time points in comparison to control, also Ag, Au and SnO2 treatment caused an increase in Fv/F0, PIABS or ET0/RC, respectively. On the other hand, TiO2-NPs caused a decrease in Fv/Fm and Fv/F0 parameters, but an increase in DI0/RC value was observed. SnO2-NPs decreased PIABS, but increased ET0/RC than compared to control. Nanoparticles affected the shape of the O-J-I-P curve in slight manner, however, further analyses showed unfavourable changes within the PSII antenna, manifested by a slowdown in the transport of electrons between the Chl molecules of the light-harvesting complex II and the active center of PSII due to NPs application.

CONCLUSION

Changes in ChlF parameters and leaf reflectance values clearly proved the significant influence of NPs on the functioning of the photosynthetic apparatus, especially right after NPs application. The nature of these changes was strictly depended on the type of nanoparticles and sometimes underwent very significant changes over time. The greatest changes in ChlF parameters were caused by Fe2O3 nanoparticles, followed by TiO2-NPs. After slight response of O-J-I-P curves to treatment of the plants with NPs the course of the light phase of photosynthesis stabilized and at 9th day were comparable to the control curve.

Metal oxide nanoparticles inhibit nitrogen fixation and rhizosphere colonization by inducing ROS in associative nitrogen-fixing bacteria Pseudomonas stutzeri A1501

The potential effects of engineered metal oxide nanoparticles (MONPs) on bacterial nitrogen fixation are of great concern. Herein, the impact and mechanism of the increasing-used MONPs, including TiO₂, Al₂O₃, and ZnO nanoparticles (TiO₂NP, Al₂O₃NP, and ZnONP, respectively), on nitrogenase activity was studied at the concentrations ranging from 0 to 10 mg L^-1 using associative rhizosphere nitrogen-fixing bacteria Pseudomonas stutzeri A1501. Nitrogen fixation capacity was inhibited by MONPs in an increasing degree of TiO₂NP < Al₂O₃NP < ZnONP. Realtime qPCR analysis showed that the expressions of nitrogenase synthesis-related genes, including nifA and nifH, were inhibited significantly when MONPs were added. MONPs could cause the explosion of intracellular ROS, and ROS not only changed the permeability of the membrane but also inhibited the expression of nifA and biofilm formation on the root surface. The repressed nifA gene could inhibit transcriptional activation of nif-specific genes, and ROS reduced the biofilm formation on the root surface which had a negative effect on resisting environmental stress. This study demonstrated that MONPs, including TiO₂NP, Al₂O₃NP, and ZnONP, inhibited bacterial biofilm formation and nitrogen fixation in the rice rhizosphere, which might have a negative effect on the nitrogen cycle in bacteria-rice system.

Nanofertilizers: Types, Delivery and Advantages in Agricultural Sustainability

In an alarming tale of agricultural excess, the relentless overuse of chemical fertilizers in modern farming methods have wreaked havoc on the once-fertile soil, mercilessly depleting its vital nutrients while inflicting irreparable harm on the delicate balance of the surrounding ecosystem. The excessive use of such fertilizers leaves residue on agricultural products, pollutes the environment, upsets agrarian ecosystems, and lowers soil quality. Furthermore, a significant proportion of the nutrient content, including nitrogen, phosphorus, and potassium, is lost from the soil (50–70%) before being utilized. Nanofertilizers, on the other hand, use nanoparticles to control the release of nutrients, making them more efficient and cost-effective than traditional fertilizers. Nanofertilizers comprise one or more plant nutrients within nanoparticles where at least 50% of the particles are smaller than 100 nanometers. Carbon nanotubes, graphene, and quantum dots are some examples of the types of nanomaterials used in the production of nanofertilizers. Nanofertilizers are a new generation of fertilizers that utilize advanced nanotechnology to provide an efficient and sustainable method of fertilizing crops. They are designed to deliver plant nutrients in a controlled manner, ensuring that the nutrients are gradually released over an extended period, thus providing a steady supply of essential elements to the plants. The controlled-release system is more efficient than traditional fertilizers, as it reduces the need for frequent application and the amount of fertilizer. These nanomaterials have a high surface area-to-volume ratio, making them ideal for holding and releasing nutrients. Naturally occurring nanoparticles are found in various sources, including volcanic ash, ocean, and biological matter such as viruses and dust. However, regarding large-scale production, relying solely on naturally occurring nanoparticles may not be sufficient or practical. In agriculture, nanotechnology has been primarily used to increase crop production while minimizing losses and activating plant defense mechanisms against pests, insects, and other environmental challenges. Furthermore, nanofertilizers can reduce runoff and nutrient leaching into the environment, improving environmental sustainability. They can also improve fertilizer use efficiency, leading to higher crop yields and reducing the overall cost of fertilizer application. Nanofertilizers are especially beneficial in areas where traditional fertilizers are inefficient or ineffective. Nanofertilizers can provide a more efficient and cost-effective way to fertilize crops while reducing the environmental impact of fertilizer application. They are the product of promising new technology that can help to meet the increasing demand for food and improve agricultural sustainability. Currently, nanofertilizers face limitations, including higher costs of production and potential environmental and safety concerns due to the use of nanomaterials, while further research is needed to fully understand their long-term effects on soil health, crop growth, and the environment.

Biosynthesis of Nanoparticles from Various Biological Sources and Its Biomedical Applications

In the last few decades, the broad scope of nanomedicine has played an important role in the global healthcare industry. Biological acquisition methods to obtain nanoparticles (NPs) offer a low-cost, non-toxic, and environmentally friendly approach. This review shows recent data about several methods for procuring nanoparticles and an exhaustive elucidation of biological agents such as plants, algae, bacteria, fungi, actinomycete, and yeast. When compared to the physical, chemical, and biological approaches for obtaining nanoparticles, the biological approach has significant advantages such as non-toxicity and environmental friendliness, which support their significant use in therapeutic applications. The bio-mediated, procured nanoparticles not only help researchers but also manipulate particles to provide health and safety. In addition, we examined the significant biomedical applications of nanoparticles, such as antibacterial, antifungal, antiviral, anti-inflammatory, antidiabetic, antioxidant, and other medical applications. This review highlights the findings of current research on the bio-mediated acquisition of novel NPs and scrutinizes the various methods proposed to describe them. The bio-mediated synthesis of NPs from plant extracts has several advantages, including bioavailability, environmental friendliness, and low cost. Researchers have sequenced the analysis of the biochemical mechanisms and enzyme reactions of bio-mediated acquisition as well as the determination of the bioactive compounds mediated by nanoparticle acquisition. This review is primarily concerned with collating research from researchers from a variety of disciplines that frequently provides new clarifications to serious problems.

A State-of-Art Review of the Metal Oxide-Based Nanomaterials Effect on Photocatalytic Degradation of Malachite Green Dyes and a Bibliometric Analysis

A wide range of hard contaminants in wastewater is generated from different industries as byproducts of the organic compound. In this review, various metal oxide-based nanomaterials are employed for the photocatalytic removal of malachite green (MG) dye from wastewater. Some cost-effective and appropriate testing conditions are used for degrading these hard dyes to get higher removal efficiency. The effects of specific parameters are considered such as how the catalyst is made, how much dye is in the solution at first, how much nanocatalyst is needed to break down the dye, the initial pH of the dye solution, the type of light source used, the year of publications, and how long the dye has to be exposed to light to be removed. This study suggests that Scopus-based core collected data employ bibliometric methods to provide an objective analysis of global MG dye from 2011 to 2022 (12 years). The Scopus database collects all the information (articles, authors, keywords, and publications). For bibliometric analysis, 658 publications are retrieved corresponding to MG dye photodegradation, and the number of publications increases annually. A bibliometric study reveals a state-of-art review of metal oxide-based nanomaterials' effects on photocatalytic degradation of MG dyes (12 years).

Seasonal occurrence and fate of nanoparticles in two biological wastewater treatment plants in Southern California

Nano-sized particles in wastewater are generally considered colloids, but their production and size distribution are not well understood. Organic nano-sized particles are more abundant than engineered nanomaterials in wastewater, where they may cause membrane fouling, harbor pathogens, and transport contaminants to the environment. To our knowledge, this study is the first to examine the seasonal behavior, removal, and the quantity and size of suspended particles (both unfiltered and filtered through a 450 nm filter) at multiple points within different processes along two water resource recovery facilities (WRRFs, formerly wastewater treatment plants). In Southern California where wastewater is often reused or reclaimed, a better understanding of nano-sized particles generation and removal may help reduce cost. We found that both types of the biological secondary treatments investigated (conventional activated sludge process and trickling filter) were more efficient in removing suspended particles larger than 450 nm than they were smaller ones. However, the results show that current treatment processes are not designed to remove nano-sized particles efficiently. We also investigated the factors that correlate with their occurrence and found that there was a significant and direct correlation between influent dissolved chemical oxygen demand (COD) and the abundance of suspended particles both larger and smaller than 450 nm, suggesting that the suspended particles increased with dissolved COD in the WRRFs and thus were biogenically generated during the wastewater treatment. Although no conclusive seasonal correlations were found, dissolved COD management may control nano-sized particle production. PRACTITIONER POINTS: Conventional secondary treatments (activated sludge and trickling filter) could efficiently remove particles but not as efficiently for nano-sized particles (40.1-52.7% removal). At one facility, particles of all sizes were found to correlate with dissolved carbon and EPS, meaning they were biogenic. Monitoring dissolved carbon or EPS precursors may help control membrane fouling post-secondary treatment, and this warrants more studies.

Fascinating strategies of marine benthic organisms to cope with emerging pollutant: Titanium dioxide nanoparticles

Titanium dioxide nanoparticles (NPs) have numerous applications, and their demands have increased as an alternative for banned sunscreen filters. However, the underlying mechanisms of their toxicity, remain largely unknown. Here, we investigate the mechanism of TiO₂ NP cytotoxicity and detoxification through time-course experiments (1, 6, and 24 h) based on cellular observations and single-cell transcriptome analyses in a marine benthic foraminifer strain, derived from a common unicellular eukaryotic organism worldwide. After exposure for 1 h, cells enhanced the production of reactive oxygen species (ROS) in acidic endosomes containing TiO₂ NPs as well as in mitochondria. In acidic endosomes, ROS were produced through the Fenton reaction on the surface of charged TiO₂ NPs. In mitochondria, ROS were associated with porphyrin synthesis that chelated metal ions. Glutathione peroxide and neutral lipids acted as a sink for free radicals, whereas lipid peroxides were excreted to prevent further radical chain reactions. By 24 h, aggregated TiO₂ NPs were encapsulated in organic compounds, possibly ceramide, and excreted as mucus, thereby preventing their further uptake. Thus, we reveal that foraminifers can tolerate the toxicity of TiO₂ NPs and even prevent their further phagocytosis and uptake by trapping TiO₂ NPs inside mucus. This previously unknown strategy could be applied in bioremediation to sequester NPs from the marine environment and can guide management of TiO₂ pollution.

Methacrylate Cationic Nanoparticles Activity against Different Gram-Positive Bacteria

Nanotechnology is a developing field that has boomed in recent years due to the multiple qualities of nanoparticles (NPs), one of which is their antimicrobial capacity. We propose that NPs anchored with 2-(dimethylamino)ethyl methacrylate (DMAEMA) have antibacterial properties and could constitute an alternative tool in this field. To this end, the antimicrobial effects of three quaternised NPs anchored with DMAEMA were studied. These NPs were later copolymerized using different methylmethacrylate (MMA) concentrations to evaluate their role in the antibacterial activity shown by NPs. Clinical strains of Staphylococcus aureus, S. epidermidis, S. lugdunensis and Enterococcus faecalis were used to assess antibacterial activity. The minimal inhibitory concentration (MIC) was determined at the different concentrations of NPs to appraise antibacterial activity. The cytotoxic effects of the NPs anchored with DMAEMA were determined in NIH3T3 mouse fibroblast cultures by MTT assays. All the employed NPs were effective against the studied bacterial strains, although increasing concentrations of the MMA added during the synthesis process diminished these effects without altering toxicity in cell cultures. To conclude, more studies with other copolymers are necessary to improve the antibacterial effects of NPs anchored with DMAEMA.

Perspectives of nanomaterials in microbial remediation of heavy metals and their environmental consequences: A review

Nanomaterials (NMs) have diverse applications in various sectors, such as decontaminating heavy metals from drinking water, wastewater, and soil. Their degradation efficiency can be enhanced through the application of microbes. As microbial strain releases enzymes, which leads to the degradation of HMs. Therefore, nanotechnology and microbial-assisted remediation-based methods help us develop a remediation process with practical utility, speed, and less environmental toxicity. This review focuses on the success achieved for the bioremediation of heavy metals by nanoparticles and microbial strains and in their integrated approach. Still, the use of NMs and heavy metals (HMs) can negatively affect the health of living organisms. This review describes various aspects of the bioremediation of heavy materials using microbial nanotechnology. Their safe and specific use supported by bio-based technology paves the way for their better remediation. We discuss the utility of nanomaterials for removing heavy metals from wastewater, toxicity studies and issues to the environment with their practical implications. Nanomaterial assisted heavy metal degradation coupled with microbial technology and disposal issues are described along with detection methods. Environmental impact of nanomaterials is also discussed based on the recent work conducted by the researchers. Therefore, this review opens new avenues for future research with an impact on the environment and toxicity issues. Also, applying new biotechnological tools will help us develop better heavy metal degradation routes.

Zinc oxide nanoparticles induce oxidative stress, genotoxicity, and apoptosis in the hemocytes of Bombyx mori larvae

The expanded uses of zinc oxide nanoparticles (ZnO-NPs) have grown rapidly in the field of nanotechnology. Thus, the increased production of nanoparticles (NPs) increases the potential risks to the environment and occupationally exposed humans. Hence, safety and toxicity assessment including genotoxicity of these NPs is indispensable. In the present study, we have evaluated the genotoxic effect of ZnO-NPs on 5th larval instar of Bombyx mori after feeding on mulberry leaves treated with ZnO-NPs at concentrations 50 and 100 μg/ml. Moreover, we evaluated its effects on total and different hemocyte count, antioxidant potential and catalase activity on the hemolymph of treated larvae. Results showed that ZnO-NPs at concentrations of 50 and 100 µg/ml have significantly decreased the total hemocyte count (THC) and different hemocyte count (DHC) except the number of oenocytes as they were significantly increased. Gene expression profile also showed up-regulation of GST, CNDP2 and CE genes suggesting increase in antioxidant activity and alteration in cell viability as well as cell signaling.

Nanomaterials in agriculture for plant health and food safety: a comprehensive review on the current state of agro-nanoscience

In the modern epoch, nanotechnology took forward the agriculture and food industry with new tools that promise to increase food production sustainably. It also anticipated that it would become a driving economic force shortly. Nanotechnology has the potential to reduce agricultural inputs, enrich the soil by absorbing nutrients, manage plant diseases, and detect diseases. The aim of the present review is to cover the potential aspects of nanoscience and its trend-setting appliances in modern agriculture and food production. This review focuses on the impact of various nanomaterials on plant health to improve agricultural production and its cooperative approach to food production. Nanotechnology has great potential compared to conventional approaches. The appealing path of nanotrends in the farming sector raises hopes and illuminates the route of innovative technologies to overcome various diseases in plants with an enhanced yield to meet the growing global population's need for food security.

Structural parameters of nanoparticles affecting their toxicity for biomedical applications: a review

Rapidly growing interest in using nanoparticles (NPs) for biomedical applications has increased concerns about their safety and toxicity. In comparison with bulk materials, NPs are more chemically active and toxic due to the greater surface area and small size. Understanding the NPs' mechanism of toxicity, together with the factors influencing their behavior in biological environments, can help researchers to design NPs with reduced side effects and improved performance. After overviewing the classification and properties of NPs, this review article discusses their biomedical applications in molecular imaging and cell therapy, gene transfer, tissue engineering, targeted drug delivery, Anti-SARS-CoV-2 vaccines, cancer treatment, wound healing, and anti-bacterial applications. There are different mechanisms of toxicity of NPs, and their toxicity and behaviors depend on various factors, which are elaborated on in this article. More specifically, the mechanism of toxicity and their interactions with living components are discussed by considering the impact of different physiochemical parameters such as size, shape, structure, agglomeration state, surface charge, wettability, dose, and substance type. The toxicity of polymeric, silica-based, carbon-based, and metallic-based NPs (including plasmonic alloy NPs) have been considered separately.