A novel solid digestate-derived biochar-Cu NP composite activating H2O2 system for simultaneous adsorption and degradation of tetracycline

Removal of Pb pollution using alginate-coupled magnetic sludge biochar: Solidification and stabilization behavior and electron promotion mechanisms

Environmental and human health problems caused by Pb pollution have attracted much attention, and solidification and stabilization are effective means for its remediation. Improving the ability of biochar to remediate heavy metals through modification is the focus of current biochar research. This study used calcium-alginate gel (GB) and Fe3+ (magnetic) to encapsulate and improve sludge biochar (SB), and explored the adsorption behavior and passivation mechanism of Pb2+ on it from outside to inside. The magnetic-biochar (MB) in magnetic-biochar-gel microspheres (MBGB) showed a homogeneous dispersion and part of the Fe ion was detached from the MB into the three-dimensional pores of the gel. The results of kinetic, isothermal and pH adsorption experiments showed that the MBGB has 108.4 % and 200 % higher Pb2+ adsorption capacity and rate than SB and can be applied to pH 3-9. The adsorption of Pb2+ by MBGB is a multilayer adsorption with both physical and chemical mechanisms. Mineralogical and electrochemical results demonstrate that the cross-linking of the gel with magnetic-biochar (MB) can provide a directional diffusion channel for Pb2+ from the outside to the inside. The electron transfer rate of MBGB was significantly higher than that of SB (222.2 %) after the reaction. The dissolved cations and electrons on the MB guide Pb2+ from the MBGB surface to the internal MB quickly via accelerating the electron transfer and migration rate between Pb2+ and MB. Subsequently, the abundance of PO43- on the MB ensures stable mineral precipitation (Pyromorphite). Moreover, four-step extraction analysis confirmed that most of Pb2+ in MBGB was stable (36.2 % acid-soluble and 47.6 % non-bioavailable). Meanwhile, the Pb adsorption efficiency of MBGB was still >93.0 % after three cycles of adsorption-desorption. Excellent reuse performance and stability guarantee the environmental security of MBGB. The results of the study provide theoretical support for the efficient treatment of Pb2+ polluted water assisted by gel materials.

A comprehensive review on the preparation of biochar from digestate sources and its application in environmental pollution remediation

The preparation of biochar from digestate is one of the effective ways to achieve the safe disposal and resource utilization of digestate. Nevertheless, up to now, a comprehensive review encompassing the factors influencing anaerobic digestate-derived biochar production and its applications is scarce in the literature. Therefore, to fill this gap, the present work first outlined the research hotspots of digestate in the last decade using bibliometric statistical analysis with the help of VOSviewer. Then, the characteristics of the different sources of digestate were summarized. Furthermore, the influencing factors of biochar preparation from digestate and the modification methods of digestate-derived biochar and associated mechanisms were analyzed. Notably, a comprehensive synthesis of anaerobic digestate-derived biochar applications is provided, encompassing enhanced anaerobic digestion, heavy metal remediation, aerobic composting, antibiotic/antibiotic resistance gene removal, and phosphorus recovery from digestate liquor. The economic and environmental impacts of digestate-derived biochar were also analyzed. Finally, the development prospect and challenges of using biochar from digestate to combat environmental pollution are foreseen. The aim is to not only address digestate management challenges at the source but also offer a novel path for the resourceful utilization of digestate.

A review of the next-generation biochar production from waste biomass for material applications

The development of carbonaceous materials such as biochar has triggered a hot spot in materials application. Carbon material derived from biomass could be a vital platform for energy storage and conversion. Biochar-based materials deliver a novel approach to deal with the current energy-related challenges. To design and utilize the maximum potential of biochar for environmentally sustainable applications, it is crucial to understand the recent progress and advancement in molecular structures of biochar to discover a new possible field to simplify structural application networks. However, most of the studies demonstrated the application of biochar in the form of soil enhancers and bio-adsorbents, reducing soil emissions of greenhouse gases and as fertilizers. The present review on biochar highlighted the application of biochar-based materials in various energy storage and conversion sectors, comprising different types of conversion technologies, biochar formation mechanisms, modification techniques on biochar surface chemistry and its functionality, catalysts, biochar application in energy storage gadgets such as supercapacitors and nanotubes, bio-based composite materials and inorganic based composites materials. Finally, this review addressed some vital outlooks on the prospect of the functionalization and best utilization of biochar-supported materials in numerous energy storage and conversion fields. After reviewing the literature, it was directed that advanced and in-depth research is essential for structural analysis and separation, considering the macroscopic and microscopic evidence of the formed structural design of biochar for specific applications.

New Insights on Designing the Next-Generation Materials for Electrochemical Synthesis of Reactive Oxidative Species Towards Efficient and Scalable Water Treatment: A Review and Perspectives

Electrochemical water remediation technologies offer several advantages and flexibility for water treatment and degradation of contaminants. These technologies generate reactive oxidative species (ROS) that degrade pollutants. For the implementation of these technologies at an industrial scale, efficient, scalable, and cost-effective in-situ ROS synthesis is necessary to degrade complex pollutant mixtures, treat large amount of contaminated water, and clean water in a reasonable amount of time and cost. These targets are directly dependent on the materials used to generate the ROS, such as electrodes and catalysts. Here, we review the key design aspects of electrocatalytic materials for efficient in-situ ROS generation. We present a mechanistic understanding of ROS generation, including their reaction pathways, and integrate this with the key design considerations of the materials and the overall electrochemical reactor/cell. This involves tunning the interfacial interactions between the electrolyte and electrode which can enhance the ROS generation rate up to ~ 40% as discussed in this review. We also summarized the current and emerging materials for water remediation cells and created a structured dataset of about 500 electrodes and 130 catalysts used for ROS generation and water treatment. A perspective on accelerating the discovery and designing of the next generation electrocatalytic materials is discussed through the application of integrated experimental and computational workflows. Overall, this article provides a comprehensive review and perspectives on designing and discovering materials for ROS synthesis, which are critical not only for successful implementation of electrochemical water remediation technologies but also for other electrochemical applications.

Qualitative and Quantitative Investigation of Biochar-Cu0 Composite for Nickel Adsorption

The current investigation deals with the treatment of water pollution that is caused by the leaching of nickel ions from the metallurgical industry and new-energy batteries. Therefore, an eco-friendly treatment of nickel through the use of a composite of cotton stalk biochar with nanozerovalent copper has been presented in this investigation signifying the impact of zerovalent copper in enhancing the adsorption capacity of biochar for nickel adsorption. Thermogravimetric analysis data showed the adsorbent to be significantly stable in the higher thermal range, whereas transmission electron microscopy analysis confirmed the particles to be 27 nm and also showed the cubic geometry of the particles. A much closer scanning electron microscopy analysis shows the morphology of particles to be cubic in shape. Batch adsorption indicated a positive influence of pH increase on adsorption due to the electrostatic attraction between positive nickel ions and post point of zero charge (pHPZC) negative surface of copper biochar composite (pH > 5.5). A high adsorption rate was observed in the first 60 min, whereas adsorption increased with the increase in temperature from 303 to 318 K. Kinetic modeling confirmed the pseudo-first-order to fit best to the data. The apparent activation energy (11.96 kJ mol-1) is indicative of the chemical nature of the process. The adsorption data fitted well to the Langmuir adsorption model. The negative values of apparent ΔG° and the positive values of apparent ΔH° indicate the spontaneity and endothermicity of the process, respectively, whereas the positive values of apparent ΔS° point toward increased randomness during the process. Postadsorption XPS suggests the adsorption of nickel on the surface of biochar composites in the form of Ni(OH)2 and NiO(OH).

Synthesis of Cu Nanoparticles Incorporated Mesoporous C/SiO2 for Efficient Tetracycline Degradation

In this study, a Cu NPs-incorporated carbon-containing mesoporous SiO2 (Cu/C-SiO2) was successfully synthesized through a grinding-assisted self-infiltration method followed by an in situ reduction process. The obtained Cu/C-SiO2 was then employed as a Fenton-like catalyst to remove tetracycline (TC) from aqueous solutions. TEM, EDS, XRD, N2 adsorption-desorption, FTIR, and XPS methods were used to characterize the crystal structure, morphology, porosity, chemical composition, and surface chemical properties of the catalyst. The effects of initial TC concentration, catalyst dosage, H2O2 dosage, solution pH, HA addition, and water media on the TC degradation over Cu/C-SiO2 were investigated. Scavenging and electrochemical experiments were then carried out to analyze the TC degradation mechanism. The results show that the Cu/C-SiO2 can remove 99.9% of the concentrated TC solution (C0 = 500 mg·L-1), and it can be used in a wide pH range (R.E. = 94-99%, pH = 3.0-11.0). Moreover, hydroxyl radicals (•OH) were detected to be the dominant reactive species in this catalytic system. This study provides a simple and promising method for the synthesis of heteroatom-containing mesoporous catalysts for the decomposition of antibiotics in wastewater.

H2O2 activation and contaminants removal in heterogeneous Fenton-like systems

Emerging contaminants can be removed effectively in heterogeneous Fenton-like systems. Currently, catalyst activity and contaminant removal mechanisms have been studied extensively in Fenton-like systems. However, a systematic summary was lacking. This review summarized: 1) The effects of various heterogeneous catalysts on emerging contaminants degradation by activating H₂O₂; 2) The role of active sites in different catalysts during the activation of H₂O₂ and their contribution to the generation of active species; 3) The modulation of degradation pathways of emerging contaminants. This paper will help scholars to advance the controlled construction of active sites in heterogeneous Fenton-like systems. Suitable heterogeneous Fenton catalysts can be selected in practical water treatment processes.

Digestate-derived carbonized char and activated carbon: Application perspective

The flourishment of anaerobic digestion (AD) on waste treatment emphasizes the importance of digestate valorization, which plays an essential role in determining the benefits provided by the AD process. The perception of digestate gradually shifts from waste to products to realize the concept of circular economy and maximize the benefits of digestate valorization. This review first outlined the current status of digestate valorization, focusing on thermal-chemical methods. The novel valorization methods were then summarized from the recent research, illustrating prospects for digestate valorization. Limits and perspectives are finally addressed. Methods for preparing digestate-derived activated carbon and impurity effects were elucidated. Inherent mineral content/inorganic impurity could be a niche for downstream use. High surface area and well-developed pore structure are essential for satisfying downstream use performance, but they are not the only factors. Digestate char applications other than use as an energy fuel are suggested.

Complexation and degradation of tetracycline by activation of molecular oxygen with biochar-supported nano-zero-valent copper composite

Nano-zero-valent copper (nZVC) is a superior molecular oxygen (O₂) activator for the abatement of organic pollutants due to its high electron utilization rate. However, the activation efficiency of O₂ is compromised by the agglomeration tendency of nZVC particles and the concomitant reduction of the available active sites. To address this problem, the biochar (BC) with porous structure and abundant surface functional groups is utilized to disperse and stabilize nZVC for O₂ activation (simplified as the nZVC/BC/O₂ system) for efficient removal of tetracycline (TC). The nZVC/BC composite possesses a high specific area with well-distributed nZVC particles on the BC surface, which guarantees the superior dispersion and high reactivity in the activation of O₂. The efficacy of the nZVC/BC/O₂ system for TC abatement is evaluated and the underlying mechanism is elucidated. The results show that nZVC/BC/O₂ system can achieve excellent removal of TC with the efficiencies of more than 85% in the pH range of 4.0-9.0, which originated from the combined action of complexation and degradation. The degradation is dominated by reactive oxygen species (ROS) including •OH, •O₂^- and ¹O₂ generated by Cu⁰/Cu⁺ activated O₂ while the generation of Cu²⁺ via oxygen oxidation on the surface of nZVC/BC can remove TC by complexation adsorption. This study highlights the complexation and degradation in the removal of TC and can be expected to exhibit application prospects in the water and wastewater treatment.

Degradation of organic pollutants from water by biochar-assisted advanced oxidation processes: Mechanisms and applications

Biochar has shown large potential in environmental remediation because of its low cost, large specific surface area, porosity, and high conductivity. Biochar-assisted advanced oxidation processes (BC-AOPs) have recently attracted increasing attention to the remediation of organic pollutants from water. However, the effects of biochar properties on catalytic performance need to be further explored. There are still controversial and knowledge gaps in the reaction mechanisms of BC-AOPs, and regeneration methods of biochar catalysts are lacking. Therefore, it is necessary to systematically review the latest research progress of BC-AOPs in the treatment of organic pollutants in water. In this review, first of all, the effects of biochar properties on catalytic activity are summarized. The biochar properties can be optimized by changing the feedstocks, preparation conditions, and modification methods. Secondly, the catalytic active sites and degradation mechanisms are explored in different BC-AOPs. Different influencing factors on the degradation process are analyzed. Then, the applications of BC-AOPs in environmental remediation and regeneration methods of different biochar catalysts are summarized. Finally, the development prospects and challenges of biochar catalysts in environmental remediation are put forward, and some suggestions for future development are proposed.

A critical review on biochar-based catalysts for the abatement of toxic pollutants from water via advanced oxidation processes (AOPs)

Proper waste disposal is a key towards sustainable development. Wastewater treatment is delineated by the application of efficient, economic and novel catalysts. Biochar is derived from the thermochemical conversion of biomass or any carbonaceous materials and is considered as one of the most eco-friendly substitute for activated carbon. Owing to its large surface area, porosity, crystallinity and active functional groups, the biochar-based catalysts has been extensively applied for the abatement of toxic pollutants from wastewater streams. While most of the reviews focus on the adsorptive properties of the biochar, this review critically analyses the recent development of biochar-based catalysts in the field of advanced oxidation processes (Fenton-like systems, photocatalytic and sonocatalytic systems). The presence of persistent free radicals and oxygen-containing functional groups renders biochar to act as catalyst. The mechanisms accompanying catalytic performance of biochar-based catalysts have also been reviewed. However, the research in this area is quite at an initial phase, and many advancements schemes are essential prior to scale-up and commercialization. Future researches should be devoted to more efficient and rigorous understanding of the structural properties of biochar to engineer the catalytic degradation of targeted pollutants in wastewater treatment.

Hydroxyapatite tailored hierarchical porous biochar composite immobilized Cd(II) and Pb(II) and mitigated their hazardous effects in contaminated water and soil

A novel composite of hydroxyapatite tailored hierarchical porous biochar (HA-HPB) was synthesized and used for the adsorptive immobilization of Cd(II) and Pb(II) in water and soil. The hierarchical porous biochar (HPB) was prepared from rice husk through a molten-salt-assisted pyrolysis approach; then, a series of HA-HPB (with 0.5, 1, 2, 3, and 4 g of HPB) was prepared with co-precipitation procedure. All HA-HPBs, particularly HA-3HPB, revealed significantly higher removal efficiency of Cd(II) and Pb(II) (≥99.5%) in water than pristine biochar (5.79 - 24.12%). The immobilization efficiency of HA-3HPB for Cd(II) and Pb(II) was slightly inhibited by the ionic strength and co-existing cations. The Langmuir adsorption capacities of Cd(II) and Pb(II) were 88.1 and 110.2 mg/g, respectively. Ion exchange, complexation, cation-π interaction, and precipitation were the key mechanisms involved in the immobilization of Cd(II) and Pb(II) using HA-3HPB. The HA-3HPB reduced the availability of soil Cd (63.5 - 87.8%) and Pb (64.6 - 92.9%) compared to the unamended soil, and thus reduced their content in the Chinese cabbage shoots by 69.3 -95.4% for Cd and 66.5 -97.2% for Pb. These findings demonstrate the effectiveness of HA-HPB for remediation of Cd(II) and Pb(II) contaminated water and soil and mitigating the potential risks.

Improved photodegradation of antibiotics pollutants in wastewaters by advanced oxidation process based on Ni-doped TiO2

The number of antibiotic compounds in wastewaters has been growing globally due to the covid-19 problem. Using antibiotics to treat the patients would produce larger amounts of these compounds into the environment with negative impacts. Hence, finding out the method for the elimination of toxic organic pollutants as well as antibiotics in water is urgent (In this study, the treatment of antibiotic pollutants including cefalexin (CF) and tetracycline (TC) was investigated by applying the advanced oxidation process based on Ni-doped TiO₂ (Ni-TiO₂). The characterizations technologies such as XRD, XPS, UV-vis, PL, and PC indicated that Ni doping would improve the photocatalytic performance of TiO₂. In the photodegradation experiments, the Ni-TiO₂ possessed high photocatalytic degradation efficiencies with 93.6% for CF and 82.5% for TC. Besides, the removal rates of antibiotics after five cycles are higher than 75%, implying excellent stability of Ni-TiO₂ photocatalyst. The result from the treatment of wastewater samples revealed that the Ni-TiO₂ photocatalytic had good performance for removal of CF and TC at a high level of 88.6 and 80.2%, respectively.

Enhanced degradation of tetracycline over FeS-based Fenton-like process: Autocatalytic decomposition of H2O2 and reduction of Fe(III)

This study constructed a FeS-based Fenton-like process to explore the degradation of TTC in the presence of copper ions. The acidic condition of pH 3 was more favorable to the H₂O₂ decomposition and TTC degradation, and it was slightly enhanced by Cu(II). The production of •OH from H₂O₂ was revealed through radical scavenging and benzoic acid probe experiments, and the ratio of H₂O₂ decomposition to •OH production was about 1-1.5, which is comparatively consistent with the theoretical ratio. FeS-based Fenton process was proved to be a homogenous system, the slow release of Fe(II) source and the autocatalytic cycle of Fe(III) to Fe(II) resulting from the reductive species of TTC and dissolved S(-II) improved the production of •OH and the degradation of TTC, which was proved by comparing TTC degradation, TOC removal, H₂O₂ decomposition and Fe(II) concentration with different iron sources (FeS, Fe(II) and Fe(III)) and external addition of dissolved S(-II). The possible degradation pathways of TTC were subsequently inferred according to the detected products by LC-MS. Understanding these autocatalytic processes is essential to reveal the transformation of redox-active substances in environments and may have potential significance in applying FeS-based Fenton-like process for the treatment of wastewater containing reductive organic matters.

Preparation of BiFeO3 and photodegradation of tetracycline pollutant in the UV-heterogeneous Fenton-like system

Surplus tetracycline in the water body causes damage to the ecology balance and human health. Therefore, this work established an efficient strategy, namely, the BFO-based UV-heterogeneous Fenton-like system, to eliminate TC pollution. The photocatalytic oxidation system has been integrated with the heterogeneous Fenton-like system, cooperated with the photolysis of H₂O₂. These synergistic effects could boost the generation of reactive species for the TC degradation and mineralization, due to the reduction of Fe(III) to Fe(II) by photogenerated electrons and the separation of photogenerated electron-hole pairs. The prepared BFO was stable with no secondary pollution, and could be recovered by an extra magnet to reuse. Compared with other single oxidation systems, this coupled system showed an outstanding performance in TC disposal, and TC and TOC removal efficiencies could reach 100% and 74.92%, respectively. Moreover, the mechanisms for TC degradation involved that TC was degraded by oxidation species, such as superoxide radicals, hydroxyl radicals, and positive holes, and intermediate products in the TC degradation process mainly were products at m/z = 459, m/z = 445, and m/z = 134. The promising TC disposal efficiency achieved by the integration between BFO-based photocatalytic and heterogeneous Fenton-like system sheds light on applying BFO to control water pollution.

Treatment of As(III)-Laden Contaminated Water Using Iron-Coated Carbon Fiber

This work presents the fabrication, characterization, and application of iron-coated carbon fiber (Fe@CF), synthesized in a facile in situ iron reduction, for As(III) removal from an aqueous solution. The physico-chemical properties of the composite were characterized using Brunauer–Emmett–Teller (BET) surface area, scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier-transform infrared (FTIR) spectroscopy. Adsorption studies were evaluated in batch experiments with respect to reaction time, the dose of adsorbent, As(III) initial concentration, pH, and co-existing ions. The results showed that the BET surface area and pore volume of Fe@CF slightly decreased after Fe coating, while its pore size remained, while the SEM and XRD analyses demonstrated that the Fe was successfully anchored on the CF. A maximum As(III) adsorption of 95% was achieved with an initial As concentration of 1.5 mg/L at optimum conditions (30 min of reaction time, 1 g/L of dose, 1 mg/L of As(III) concentration, and pH 3.5). Since the treated effluents could not meet the strict discharge standard of ≤10 μg/L set by the World Health Organization (WHO), a longer reaction time is required to complete the removal of remaining As(III) in the wastewater effluents. As compared to the other adsorbents reported previously, the Fe@CF composite has the highest As(III) removal. Overall, the findings suggested that the use of Fe@CF as an adsorbent is promising for effective remediation in the aquatic environment.

Graphitic biochar with in situ confined magnetic iron oxides via synchronous pyrolysis of lignin as an effective H2O2 activator for fast degradation of organic pollutants

Magnetic iron oxide confined in carbon capsules/biochar composite (FeOx@g-BC) was created using in-situ synchronous pyrolysis of alkali lignin as a low-cost carbon source. Characterization results indicated the FeOx was confined in carbon nanotubes and carbon capsules, inhibiting growing of nanoparticles and deactivation. The composite catalyst demonstrated significant activity in activating H₂O₂ for the degradation of persistent organic pollutants in water over a wide pH range. Particularly, tetracycline (TC) could be completely degraded within 25 min, even at a high pH of 6.8, which performed much better than previously reported Fenton-like catalysts. Moreover, the excellent magnetism of FeOx@g-BC aided in its recovery and reuse. The stability of FeOx@g-BC recycling was also measured by continuous cycles of reactions. According to ESR analysis and free radical quenching studies, OH and ¹O₂ were discovered as the dominant active species governing the degradation of TC, and two pathways of TC degradation were proposed. This study developed a novel heterogeneous catalyst for catalytic degradation of persistent organic contaminants in water by the value-added usage of lignin.

Waste preserved wood derived biochar catalyst for promoted peroxymonosulfate activation towards bisphenol A degradation with low metal ion release: The insight into the mechanisms

The rational disposal of waste preserved wood is of great significance since its embedded metals (Cu, As, and Cr) pose potential threat to environment and human health. In this study, a biochar catalyst derived from waste preserved wood (PWB) was prepared for the degradation of bisphenol A (BPA) via peroxymonosulfate (PMS) activation. The PWB exhibited prominent catalytic degradation capability towards BPA compared with common wood derived biochar (CWB). Further tests and analysis elucidated that both radical species (OH) and non-radical species (¹O₂) were generated by the PWB/PMS system, whereas only ¹O₂ was detected in CWB/PMS system. Specifically, the metal compounds, especially metallic Cu in the PWB activated PMS via radical pathway, and the CO groups in the biochar generated the non-radical pathway, the coexistence of which resulted in higher BPA degradation rate in PWB/PMS system. It was also demonstrated that the heavy metal ion leaching (As and Cr) in PWB/PMS system was negligible. Furthermore, the biochar could effectively inhibit the leakage of oxidized Cu ions. This study provides a novel approach to prepare high-efficient carbocatalysts for organic pollutant degradation in water, which also enables the waste preserved wood with an environmental nondestructive mode of dispatch.

Recent advances in magnetic composites as adsorbents for wastewater remediation

The scarcity of clean drinking water combined with other environmental and anthropogenic effects necessitates the demand for development of advanced technology for cleaning polluted water. Adsorption is one such technique that does not produce toxic byproducts and solves the problem of cleaning contaminated water at a lower cost. In recent years, magnetic composites, as adsorbent, have gained lot of attention due to their reusability which makes them sustainable and economical. This review article describes the challenges related to water quality, scarcity and then summarizes the current treatment technologies and advancement in the field of adsorption to resolve the prevailing concerns. The review includes an insight into the recent research being carried out in the field of magnetic composites and nanocomposites, as adsorbent, covering, probably, all aspects of what is going around the globe. Different materials, like polymers, biomaterials, clays and metal organic framework (MOF)-based magnetic composites and their applications in wastewater treatment processes have been included. The article is a comprehensive review on the application of different materials to detoxify various diverse pollutants with prime focus on magnetic composites. The thorough study of this review will surely bring upcoming researchers closer to the future possibilities of research in wastewater treatment.

Oxidative degradation of tetracycline using peroxymonosulfate activated by cobalt-doped pomelo peel carbon composite

Tetracycline (TC) is a typical ecotoxic antibiotic, which easily causes bacterial resistance. Therefore, it is necessary to remove TC from the water environment. In recent years, advanced oxidation processes (AOPs) rely on the use of highly reactive oxidizing sulfate radical which is turning into an increasingly popular as a tool of the removal of TC. In this study, cobalt-doped pomelo peel carbon composite (Co-PPCC) was prepared by the impregnation coprecipitation method to activate peroxymonosulfate (PMS) to remove TC. SEM, BET, XRD, FTIR, XPS, TGA, and other analytical techniques indicated that a carbon composite catalyst with excellent performance has been successfully prepared. TC was removed by the synergistic effect of adsorption and catalytic degradation processes. The adsorption capacity was limited (only approximately 20% within 60 min) and tending to saturation, which indicated that the removal of TC in the Co-PPCC/PMS system was mainly due to oxidative degradation. The influence of the Co-PPCC and PMS dosage, initial TC concentration, initial pH values, and coexisting anions on the removal efficiency of TC was investigated. When the Co-PPCC catalyst dosage was 1 g/L, PMS concentration was 2 g/L, and pH value was 11, the removal efficiency of TC with a concentration of 50 mg/L reached 99% within 60 min. Free radical quenching experiment and electron paramagnetic resonance (EPR) analysis indicated that the free radical and non-radical degradation processes exist in the Co-PPCC/PMS/TC system. The main degradation products and the possible transformation pathways of TC were explored by LC-MS. In addition, after four cycles of Co-PPCC tests, the removal efficiency of TC can reach 64%. This study provides a new method to reuse abandoned pomelo peels and synthesize an economical and environmentally friendly catalyst for activating peroxymonosulfate to remove TC antibiotics in water.

Tunable active sites on biogas digestate derived biochar for sulfanilamide degradation by peroxymonosulfate activation

Conversion of digestate into biochar-based catalysts is an effective strategy for disposal and resource utilization. The active sites on biochar correlated with reactive species formation in peroxymonosulfate (PMS) system directly. Clarifying the structure-performance relationship of digestate derived biochar in PMS system was essential for decomposition of contaminants. Herein, dairy manure digestate derived biochar (DMDB) was prepared for PMS activation and sulfamethoxazole (SMX) degradation. The higher pyrolysis temperature could promote effective sites generation. Especially, the DMDB-800 catalyst exhibited excellent performance for PMS activation, achieving 90.2% degradation of SMX within 60 min. Based on the correlation analysis between log (k) values and active sites, defects, graphite N and CO were identified as dominant sites for PMS activation. The ¹O₂ oxidation and surface electron transfer were critical routes for SMX degradation. Besides, the degradation pathways of SMX were proposed according to DFT calculations and intermediates determination. The cleavage of the sulfonamide bond, hydroxylation of the benzene ring and oxidation of the amino group mainly occurred during SMX degradation. Overall, this study provides deep insights into the enhanced mechanism of tunable active sites on DMDBs for PMS activation, boosting the application of digestate biochar for water treatment in advanced oxidation systems.

Adsorption and detoxification of pharmaceutical compounds from wastewater using nanomaterials: A review on mechanism, kinetics, valorization and circular economy

Antibiotics overuse, inappropriate conduct, and discharge have led to adverse effects on various ecosystems. The occurrence of antibiotics in surface and drinking water is a matter of global concern. It is responsible for multiple disorders, including disruption of endocrine hormones and high chronic toxicity. The hospitals, pharmaceutical industries, households, cattle farms, and aquaculture are the primary discharging sources of antibiotics into the environment. This review provides complete detail on applying different nanomaterials or nanoparticles for the efficient removal of antibiotics from the diverse ecosystem with a broader perspective. Efforts have been made to focus on the degradation pathways and mechanism of antibiotic degradation using nanomaterials. More light has been shed on applying nanostructures in photocatalysis, which would be an economical and efficient solution. The nanoscale material or nanoparticles have incredible potential for mineralizing pharmaceutical compounds in aqueous solutions at low cost, easy handling characteristics, and high efficacy. Furthermore, nanoparticles can absorb the pharmaceutical by-products and wastes at a minimum cost as they can be easily recycled. With the increasing number of research in this direction, the valorization of pharmaceutical wastes and by-products will continue to expand as we progress from old conventional approaches towards nanotechnology. The utilization of nanomaterials in pharmaceutical wastewater remediation is discussed with a major focus on valorization, energy generation, and minimization and its role in the circular economy creating sustainable development.

Magnetically modified in-situ N-doped Enteromorpha prolifera derived biochar for peroxydisulfate activation: Electron transfer induced singlet oxygen non-radical pathway

Herein, in-situ N-doped Enteromorpha prolifera derived magnetic biochar (MBC) was prepared by loading Fe₃O₄. It can effectively activate peroxodisulfate (PDS) to degrade tetracycline (TC) and easy recycling. The removal rate of TC reached 87.2%, and its possible degradation pathway was revealed through a liquid chromatography-mass spectrometer. This work first proposes the mechanism of in-situ N-doping and Fe synergistic effect on PDS activation. Unlike the well-reported role of N doping in activating PDS, except for the edge pyridine N plays a significant role in the activation of PDS. After the load of Fe, the synergistic effect of Fe and graphite N induces a non-radical path dominated by singlet oxygen (¹O₂) due to the excellent electron transfer function. Through chemical quenching experiment, electron spin detection, and electrochemical analysis, the mechanism of PDS activation by MBC was thoroughly investigate. This research will deepen the understanding of the mechanism of transition metals and carbon materials in synergistically driving PDS activation, and guide biochar-mediated PDS activation in environmental remediation.

Co-oxidative removal of arsenite and tetracycline based on a heterogeneous Fenton-like reaction using iron nanoparticles-impregnated biochar

A highly efficient, eco-friendly and relatively low-cost catalyst is necessary to tackle bottlenecks in the treatment of industrial wastewater laden with heavy metals and antibiotic such as livestock farm and biogas liquids. This study investigated co-oxidative removal of arsenite (As(III)) and tetracycline (TC) by iron nanoparticles (Fe NP)-impregnated carbons based on heterogeneous Fenton-like reactions. The composites included Fe NP@biochar (BC), Fe NP@hydrochar (HC), and Fe NP@HC-derived pyrolysis char (HDPC). The functions of N and S atoms and the loading mass of the Fe NP in the Fe NP@BC in heterogeneous Fenton-like reactions were studied. To sustain its cost-effectiveness, the spent Fe NP@BC was regenerated using NaOH. Among the composites, the Fe NP@BC achieved an almost complete removal of As(III) and TC under optimized conditions (1.0 g/L of dose; 10 mM H₂O₂; pH 6; 4 h of reaction; As(III): 50 μM; TC: 50 μM). The co-oxidative removal of As(III) and TC by the Fe NP@ BC was controlled by the synergistic interactions between the Fe NPs and the active N and S sites of the BC for generating reactive oxygen species (ROS). After four consecutive regeneration cycles, about 61 and 95% of As(III) and TC removal were attained. This implies that the spent carbocatalyst still has reasonable catalytic activities for reuse. Overall, this suggests that adding technological values to unused biochar as a carbocatalyst like Fe NP@BC was promising for co-oxidative removal of As(III) and TC from contaminated water.

Bioengineered biochar as smart candidate for resource recovery toward circular bio-economy: a review

Biochar's ability to mediate and facilitate microbial contamination degradation, as well as its carbon-sequestration potential, has sparked interest in recent years. The scope, possible advantages (economic and environmental), and future views are all evaluated in this review. We go over the many designed processes that are taking place and show why it is critical to look into biochar production for resource recovery and the role of bioengineered biochar in waste recycling. We concentrate on current breakthroughs in the fields of engineered biochar application techniques to systematically and sustainable technology. As a result, this paper describes the use of biomass for biochar production using various methods, as well as its use as an effective inclusion material to increase performance. The impact of biochar amendments on microbial colonisation, direct interspecies electron transfer, organic load minimization, and buffering maintenance is explored in detail. The majority of organic and inorganic (heavy metals) contaminants in the environment today are caused by human activities, such as mining and the use of chemical fertilizers and pesticides, which can be treated sustainably by using engineered biochar to promote the establishment of a sustainable engineered process by inducing the circular bioeconomy.

Sustainable management and recycling of food waste anaerobic digestate: A review

Anaerobic digestion (AD) is a widely used technology to valorise food waste for biogas production yet a considerable amount of digestate remains under-utilised. Sustainable management and recycling of the nutrient-rich food waste anaerobic digestate (FWD) is highly desirable for closing resource loop and actualising circular economy. This work reviews the distinct properties of FWD and the existing treatment technologies. FWD shows great prospects as a nutrient source for microalgal cultivation and biofuel production. Emerging technologies such as thermal conversion (e.g., pyrolysis and hydrothermal treatment) of FWD into value-added products such as functionalised biochar/hydrochar with diverse applications would be attractive and warrant further research investigation. Integrated AD with subsequent valorisation facilities is highly encouraged to achieve complete utilisation of resources and reduce carbon emissions.

Novel nanocomposite of biochar-zerovalent copper for lead adsorption

In this study, a composite of zerovalent copper-biochar was investigated for its ability to remove lead from water. The prepared material was characterized by using scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR), X-ray diffractomter (XRD), and X-ray photoelectron spectroscopy (XPS). The pH effect on adsorption of lead was investigated within the range of 2-8 and the effect of temperature was studied at 303, 308, 313, and 318 K. The kinetics of lead adsorption on biochar composite was evaluated and the equilibrium time of 12 hr was established. To further evaluate the nature of adsorption, Langmuir model was tested and the adsorption capacities were evaluated for lead adsorption on the surface of copper biochar composite. The activation energy, entropy, and enthalpy values indicated the adsorption phenomenon to be chemisorptive and spontaneous in nature. Comparison of adsorption capacities with the reported adsorbents in the literature concluded zerovalent copper-biochar composite to be an efficient adsorbent for the removal of lead in the experimental conditions under study. RESEARCH HIGHLIGHTS: Highly efficient composite of zerovalent copper with biochar was synthesized for lead adsorption. XPS and XRD shows the presence of zerovalent copper in the biochar composite. pH and temperature were the main governing factors in the adsorption process. Adsorption capacity for lead is higher than many of the reported adsorbents.

Valorization of anaerobic digestion digestate: A prospect review

Anaerobic digestion is recognized as promising technology for bioenergy production from biowaste, with huge quantity of digestate being produced as the residual waste. The digestate contains substantial amounts of organic and inorganic matters that be considered highly risky contaminants to the receiving environments if not properly treated, but also potential renewable resources if are adequately recovered. This prospect review summarized the current research efforts on digestate valorization, including aspects of resource recovery and the proposed applications, particularly on the conversion techniques and economic feasibility. The prospects for digestate valorization were highlighted at the end of this review.

Enhanced degradation of organic contaminants using catalytic activity of carbonaceous structures: A strategy for the reuse of exhausted sorbents

Generation of hydroxyl radicals (⋅OH) is the basis of advanced oxidation process (AOP). This study investigates the catalytic activity of microporous carbonaceous structure for in-situ generation of ⋅OH radicals. Biochar (BC) was selected as a representative of carbon materials with a graphitic structure. The work aims at assessing the impact of BC structure on the activation of H₂O₂, the reinforcement of the persistent free radicals (PFRs) in BC using heavy metal complexes, and the subsequent AOP. Accordingly, three different biochars (raw, chemically- and physiochemically-activated BCs) were used for adsorption of two metal ions (nickel and lead) and the degradation of phenol (100 mg/L) through AOP. The results demonstrated four outcomes: (1) The structure of carbon material, the identity and the quantity of the metal complexes in the structure play the key roles in the AOP process. (2) the quantity of PFRs on BC significantly increased (by 200%) with structural activation and metal loading. (3) Though the Pb-loaded BC contained a larger quantity of PFRs, Ni-loaded BC exhibited a higher catalytic activity. (4) The degradation efficiency values for phenol by modified biochar in the presence of H₂O₂ was 80.3%, while the removal efficiency was found to be 17% and 22% in the two control tests, with H₂O₂ (no BC) and with BC (no H₂O₂), respectively. Overall, the work proposes a new approach for dual applications of carbonaceous structures; adsorption of metal ions and treatment of organic contaminants through in-situ chemical oxidation (ISCO).

Effective removal of carbamazepine and diclofenac by CuO/Cu2O/Cu-biochar composite with different adsorption mechanisms

In this study, the CuO/Cu₂O/Cu-biochar composite (CBC) was fabricated by calcining Cu²⁺-loaded cauliflower root at 500 °C. The CBC displayed the higher specific surface area and total pore volume than raw biochar, which attributed to Cu²⁺ acting as a pore-forming agent in the synthesis process. The adsorption experiments indicated that CBC could remove 88.96% diclofenac and 93.02% carbamazepine, which was nearly double higher than the raw biochar. The film diffusion mainly controlled the adsorption rate. Meanwhile, the common adsorption mechanisms for two pollutants were deemed to hydrogen-bonding interaction, π-π interaction and micropore filling effect, and copper oxide particles providing more adsorption sites. In addition, the adsorption of diclofenac involved electrostatic attraction. Lastly, the higher adsorption capacity of carbamazepine than diclofenac on CBC was mainly attributed to two mechanisms: Lewis acid-base interaction enhancing the adsorption of carbamazepine and size exclusion effect reducing the adsorption of diclofenac. Therefore, the study provided a possible method that Cu-contaminated biomass converted to CuO/Cu₂O/Cu-biochar, which could achieve win-win results.

Application of biochar in advanced oxidation processes: supportive, adsorptive, and catalytic role

The advanced oxidation processes (AOPs), especially sulphate radical (SO₄^•-)-based AOPs (SR-AOPs), have been considered more effective, selective, and prominent technologies for the removal of highly toxic emerging contaminants (ECs) due to wide operational pH range and relatively higher oxidation potential (2.5-3.1 V). Recently, biochar (BC)-based composite materials have been introduced in AOPs due to the dual benefits of adsorption and catalytic degradation, but the scientific review of BC-based catalysts for the generation of reactive oxygen species (ROSs) through radical- and non-radical-oriented routes for EC removal was rarely reported. The chemical treatments, such as acid/base treatment, chemical oxidation, surfactant incorporation, and coating and impregnation of minerals, were applied to make BC suitable as supporting materials (SMs) for the loading of Fenton catalysts to boost up peroxymonosulphate/persulphate/H₂O₂ activation to get ROSs including ^•OH, SO₄^•-, ¹O₂, and O₂^•- for targeted pollutant degradation. In this review, all the possible merits of BC-based catalysts including supportive, adsorptive, and catalytic role are summarised along with the possible route for the development prospects of BC properties. The limitations of SR-AOPs especially on production of non-desired oxyanions, as well as disinfection intermediates and their potential solutions, have been identified. Lastly, the knowledge gap and future-oriented research needs are highlighted.

Study of the Digestate as an Innovative and Low-Cost Adsorbent for the Removal of Dyes in Wastewater

Digestate, as an urban solid waste, was considered as an innovative adsorbent for colorant polluted wastewater. Batch adsorption experiments were carried out using digestate as an adsorbent material to remove various dyes belonging to different categories. The removal rate and adsorption capacity of dyes were evaluated and the dose of digestate, contact time, and initial dye concentration were studied. The maximum removal rate was approximately 96% for Methylene Blue. The equilibrium time for the Methylene Blue was 4 h, while for other dyes, a longer contact time was required to reach the equilibrium. The suspicion of colloidal matter release into the solution from solid fraction of the digestate led to the investigation of the consequence of a washing step of the digestate adsorbent upstream the adsorption experiment. Washed and not washed adsorbents were tested and the differences between them in terms of dye removal were compared. Moreover, experimental data were fitted by pseudo-first order, pseudo-second order, and intra-partial diffusion kinetic models as well as Langmuir, Freundlich, and Sips isotherm models. The results from fitted models showed that the adsorption of various dyes onto the digestate was mostly well fitted by the Langmuir isotherm and pseudo-second-order kinetic model.

Effects of feedstock and inherent mineral components on oxidation resistance of biochars

Chemical stability assessment of biochar has been universally used to indicate its potential of long-term carbon sequestration. The comparative study on oxidation resistance of biochars from diverse series of feedstock is relatively limited, as well as the effects of endogenous minerals on biochar stability. Herein, oxidation resistance of biochars from peanut shell, bamboo, saw dust, reed stalk, furfural residues, seaweed degumming residues and Enteromorpha prolifera at 500 °C (PS500, BB500, SD500, RS500, FR500, SR500 and EP500) was examined by the treatments of H₂O₂, K₂Cr₂O₇ and thermogravimetric analysis (TGA). Under H₂O₂ or K₂Cr₂O₇ condition, C loss of algae-derived biochars (SR500 and EP500) was extremely greater than that of other biochars due to higher content of labile carbon components. PS500, BB500, SD500, RS500 and FR500 characterized with similar properties in carbon fraction, but they exhibited different ability to resist oxidation. The mineral fraction of biochars (e.g., content and species) varied with the feedstock, which played complex effects on the oxidation resistance. The mineral decomposition (e.g., CaCO₃) in EP500 and SR500 above 500 °C influenced the analysis of biochar stability by TGA. After acid-washing, EP500 and SR500 showed weaker thermal oxidation resistance, agreed with the results of H₂O₂ and K₂Cr₂O₇ oxidation. The oxidation resistance of biochars was correlated better with O/C ratio, implying that O/C ratio was more robust indicator than other indexes (e.g., H/C ratio and the ratio of D band to G band of Raman). The FTIR, Raman and XPS results further demonstrated the elimination of aliphatics and amorphous aromatics and/or the carboxylation/carbonylation of aromatic structures by H₂O₂ and K₂Cr₂O₇. These findings are useful for better understanding the impacts of feedstock and inherent minerals on the oxidation resistance of biochars.

Magnetic spent bleaching earth carbon (Mag-SBE@C) for efficient adsorption of tetracycline hydrochloride: Response surface methodology for optimization and mechanism of action

The utilization of spent bleaching earth (SBE)-based materials for adsorption of pollutants from water and wastewater has received growing attention. In this work, a comparative study of magnetic spent bleaching earth carbon (Mag-SBE@C) and spent bleaching earth carbon (SBE@C) was performed to remove tetracycline hydrochloride (TCH) from aqueous solutions. Mag-SBE@C exhibits the larger adsorption capacity (0.238 mmol/g) obtained by the Langmuir model than the original SBE@C (0.150 mmol/g). The adsorption process fits well with the pseudo second-order model and is found to be exothermic (ΔH₀ < 0) and spontaneous (ΔG₀ < 0). The optimal adsorption conditions (Mag-SBE@C dose 2.217 g/L, initial TCH concentration 0.113 mmol/L, initial solution pH 6.533) predicted by the response surface methodology (RSM) are consistent with the actual verification results. The inhibition extents of coexisting cations are ranked in a decline: Al³⁺ > Cu²⁺ > Fe³⁺ > Mg²⁺ > K⁺ > Na⁺. Various characterization results indicate that the adsorption mechanism of TCH by Mag-SBE@C likely includes the π-π interactions, hydrogen bonding, electrostatic interactions, π-cations interactions, FeN covalent bonding, and changes in physical and chemical properties. Mag-SBE@C is easily solid-liquid separated using magnetic field, and can be potentially reused for 13 times before completely losing its activity, exhibiting great potential to antibiotics elimination.

Micro-interfacial mechanisms on sludge dewaterability enhancement using cerium chloride for preparation of carbon-based functional material

In this work, sludge conditioning efficiency of cerium chloride (CeCl₃) in combination with organic polymers was evaluated, the floc microstructure and extracellular polymeric substances (EPS) properties under flocculation conditioning were analyzed. The interaction mechanisms between EPS and Ce(III) were systematically investigated through two-dimension correlation spectroscopy, X-ray photoelectron spectroscopy, and confocal laser scanning microscopy. In addition, the adsorption and catalytic abilities of Ce-sludge based carbon (SBC) in tetracycline (TC) removal were evaluated. The results showed that CeCl₃ conditioning performed well in improving sludge dewaterability, and CeCl₃ and cationic polyacrylamide showed a synergistic effect in sludge conditioning. Contents of EPS decreased as the dosage of CeCl₃ increased because of charge neutralization and complexation reactions. 2D-UV-FTIR heterospectral correlation spectroscopy analysis suggested the reaction activity of EPS to Ce(III) followed the order of humic acid > protein > polysaccharide. The decrease of α-helix content improved the hydrophobicity of proteins in EPS, which was responsible for sludge dewaterability improvement in CeCl₃ conditioning. Besides, the SBC was prepared with CeCl₃ conditioned sludge for treating water containing TC. Ce-SBC had a dual function of adsorption and Fenton-like activity. This work provides a sludge recycling process that coupled chemical conditioning to pyrolysis carbonization to prepare functional carbon-based materials.

PMS activation using reduced graphene oxide under sonication: Efficient metal-free catalytic system for the degradation of rhodamine B, bisphenol A, and tetracycline

This study addresses the influence of ultrasound irradiation on the activation of peroxymonosulfate (PMS) using reduced graphene oxide (rGO) under metal-free conditions for the catalytic degradation of rhodamine B (RhB), bisphenol A (BPA) and tetracycline (TC). Our results revealed that the combination of PMS/rGO and ultrasonication enhanced significantly the degradation rate, reaching full degradation in relatively short times with total organic carbon (TOC) removal exceeding 85% of the investigated pollutants. In contrast, under these experimental conditions, rGO/ultrasound and PMS/ultrasound achieved less than 20% degradation of the same pollutants. Electron paramagnetic resonance (EPR) studies along with quenching experiments suggested that hydroxyl radicals (OH) are the dominant reactive species in the degradation process. Furthermore, inductively coupled plasma atomic emission spectroscopy (ICP-AES) and EPR data revealed the presence of trace manganese (Mn) in rGO. To elucidate the role of Mn on the degradation process, rGO was subjected to hot acid treatment for 48 h to remove trace Mn. While the chemical composition of rGO was not significantly altered by this chemical treatment, the degradation efficiency decreased upon Mn dissolution. The result suggests that trace metal in rGO might account for the efficiency of PMS activation. Finally, plausible degradation pathways were proposed based on LC-MS analysis of the reaction intermediates.

Preparation and Modification of Biochar Materials and their Application in Soil Remediation

As a new functional material, biochar was usually prepared from biomass and solid wastes such as agricultural and forestry waste, sludge, livestock, and poultry manure. The wide application of biochar is due to its abilities to remove pollutants, remediate contaminated soil, and reduce greenhouse gas emissions. In this paper, the influence of preparation methods, process parameters, and modification methods on the physicochemical properties of biochar were discussed, as well as the mechanisms of biochar in the remediation of soil pollution. The biochar applications in soil remediation in the past years were summarized, such as the removal of heavy metals and persistent organic pollutants (POPs), and the improvement of soil quality. Finally, the potential risks of biochar application and the future research directions were analyzed.

Enhanced Adsorption of Aqueous Tetracycline Hydrochloride on Renewable Porous Clay-Carbon Adsorbent Derived from Spent Bleaching Earth via Pyrolysis

In this study, spent bleaching earth (SBE) and pyrolyzed SBE (SBE@C) were tested for their capacity to remove tetracycline hydrochloride (TCH) from aqueous solution. The maximum adsorption capacity obtained by the Langmuir model is 0.114 mmol/g for SBE@C and 0.087 mmol/g for SBE. The deleterious effects of coexisting cations were ranked in a decline: Al³⁺ > Mg²⁺ > Na⁺. The results of various characterization methods show that the adsorption mechanisms mainly included π-π interactions, hydrogen bonding, electrostatic interactions, and changes in physical and chemical properties. After 3 repeated cycles of pyrolysis, the adsorption capacity of SBE@C remained at 85.4%, with SBE@C potentially recycled 21 times before complete loss of adsorption capacity. Furthermore, the problem of secondary pollution caused by SBE and residual oil is resolved by the use of SBE@C. All results indicate that SBE@C is a likely candidate for the treatment of TCH wastewater in the coming practical applications.

Removal of antibiotics from aqueous solutions by nanoparticles: a systematic review and meta-analysis

Antibiotics, as one of the emerging pollutants, are non-biodegradable compounds and long-term exposure to them may affect endocrine, hormonal, and genetic systems of human beings, representing a potential risk for both the environment and human health. The presence of antibiotics in surface waters and drinking water causes a global health concern. Many researches have stated that conventional methods used for wastewater treatment cannot fully remove antibiotic residues, and they may be detected in receiving waters. It is reported that nanoparticles could remove these compounds even at low concentration and under varied conditions of pH. The current study aimed to review the most relevant publications reporting the use of different nanoparticles to remove antibiotics from aqueous solutions. Moreover, meta-analysis was conducted on the results of some articles. Results of meta-analysis proved that different nanoparticles could remove antibiotics with an acceptable efficiency of 61%. Finally, this review revealed that nanoparticles are promising and efficient materials for degradation and removal of antibiotics from water and wastewater solutions. Furthermore, future perspectives of the new generation nanostructure adsorbents were discussed in this study.

Morphology-tunable WMoO nanowire catalysts for the extremely efficient elimination of tetracycline: kinetics, mechanisms and intermediates

The presence of antibiotics in aquatic environments has attracted global concern. The Fenton system is one of the most popular methods for eliminating antibiotics in aquatic environments, but the existing Fenton system is limited due to the potential for secondary pollution, and the narrow pH range (∼3-5). In this study, we report that the bottlenecks for high-strength tetracycline (TC) wastewater treatment under neutral conditions can be tackled well by a class of mixed-valence W/Mo containing oxides (WMoO-x) with tunable morphologies. Triethanolamine was selected as a structure-directing agent to control the morphologies of the catalysts going from ultrathin nanowires (UTNWs) to wire-tangled nanoballs (WTNBs). As a proof of concept, the most efficient catalyst in the batch samples, WMoO-1 ultrathin nanowires, was employed as a model material for TC degradation, in which the coordinatively unsaturated metal atoms with oxygen defects serve as the sites for TC chemisorption and electron transfer. As a result, 91.75% of TC was degraded in 60 min for the initial TC concentration of 400 μM. Furthermore, LC-MS analysis confirmed that the TC could be degraded to nontoxic by-products without benzene rings, and finally mineralized to CO2 and H2O. ICP-MS and cycle experiments showed the good stability and reusability of WMoO-1 UTNWs in the Fenton-like system. The findings of this work provide fresh insights into the design of nanoscale catalyst morphology and reaffirm the versatility of doping in tuning catalyst activity, extending the range of the optimal pH values to neutral conditions. This is significant for the expansion of the heterogeneous Fenton-like family and its application in the field of water treatment.

Recent advances in nanoscale-metal assisted biochar derived from waste biomass used for heavy metals removal

Pollution of heavy metals (HMs) is a detrimental treat to human health and need to be cleaned up in a proper way. Biochar (BC), a low-cost and "green" adsorbent, has attracted significant attention due to its considerable HMs removal capacity. In particular, nano-metals have recently been used to assist BC in improving its reactivity, surface texture and magnetism. Synthesis methods and metal precursors greatly influence the properties and structures of the nanocomposites, thereby affecting their HMs removal performance. This review presents advances in synthesis methods, formation mechanisms and surface characteristics of BC nanocomposites, along with the discussions on HMs removal mechanisms and the effects of environmental factors on HMs removal efficiency. Performance of using BC nanocomposites to remediate real HMs-containing wastewater and issues associated with its process scale-up are also discussed. This review aims to provide useful information to facilitate the development of HMs removal by nanoscale-metal assisted BC.