Activated carbon derived from waste orange and lemon peels for the adsorption of methyl orange and methylene blue dyes from wastewater

Cellulose-citric acid-chitosan@metal sulfide nanocomposites: Methyl orange dye removal and antibacterial activity

In this study, to develop efficient adsorbents in removing water pollution, new cellulose-citric acid-chitosan@metal sulfide nanocomposites (CL-CA-CS@NiS and CL-CA-CS@CuS) were synthesized by one-pot reaction at mild conditions and characterized using X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscope (SEM), Energy Dispersive X-ray (EDX) and Brunauer-Emmett-Teller (BET) isotherm. The results of characterization techniques confirm that the desired compounds have been successfully synthesized. The as-prepared composites were applied for the removal of methyl orange (MO) dye from aqueous solutions using a batch technique, and the effect of key factors such as initial pH, shaking time, MO concentration, temperature and adsorbent dose were investigated and discussed. Adsorption results exhibited positive impact of temperature, shaking time and adsorbent dose on the MO removal percent. The MO removal percent has been increased over a wide range of pH from 2 (27.6 %) to 6 (98.8 %). Also, almost being constant over a wide range of MO concentration (10-70 mg/L). The results demonstrated that the maximum removal percentage of MO dye (98.9 % and 93.4 % using CL-CA-CS@NiS and CL-CA-CS@CuS, respectively) was achieved under the conditions of pH 6, shaking time of 120 min, adsorbent dose of 0.02 g, MO concentration of 70 mg/L and temperature of 35 °C. The pseudo-second-order (PSO) and Langmuir models demonstrated the best fit to the kinetic and equilibrium data. Also, the thermodynamic results showed that the MO removal process is endothermic and spontaneous in nature. The MO adsorption can be happened by different electrostatic attraction, n-π and π-π stacking and also hydrogen bonding interaction. In addition, antibacterial activity of CL-CA-CS@NiS and CL-CA-CS@CuS nanocomposites exhibited a superior efficiency against S. aureus.

Valorizing date palm spikelets into activated carbon-derived composite for methyl orange adsorption: advancing circular bioeconomy in wastewater treatment-a comprehensive study on its equilibrium, kinetics, thermodynamics, and mechanisms

Leveraging date palm spikelets (DPS) as a precursor, this study developed a DPS-derived composite (ZnO@DPS-AC) for water treatment, focusing on methyl orange (MO) removal. The composite was synthesized through ZnCl2 activation and pyrolysis at 600 °C. Comprehensive characterization was conducted using TGA, FTIR, XRD, SEM/EDS, and pHPZC. Characterization revealed a highly carbonaceous material (> 74% carbon) with significant porosity and surface functional groups. ZnO@DPS-AC demonstrated rapid MO removal, achieving over 45% reduction within 10 min and up to 99% efficiency under optimized conditions. The Langmuir model-calculated maximum adsorption capacity reached 226.81 mg/g at 20 °C. Adsorption mechanisms involved hydrogen bonding, π-π interactions, and pore filling. The composite showed effectiveness in treating real wastewater and removing other pollutants. This study highlights the potential of agricultural waste valorization in developing efficient, sustainable adsorbents for water remediation, contributing to circular bioeconomy principles.

Investigation of Eucalyptus camaldulensis and Tamarix aphylla species' capacities for methylene blue removal in wastewater and heavy metal remediation in soil

In the contemporary landscape, the reuse of wastewater holds paramount significance. Concurrently, wastewater carries an array of pollutants encompassing chemical dyes and heavy metals. This study delves into the potential of Tamarix aphylla (TA) and Eucalyptus camaldulensis (EC) species for mitigating heavy metals in soil and eliminating methylene blue dye (MB) from wastewater. The research begins with assessing the dye adsorption process, considering pivotal factors such as initial pH, adsorbent dosage, initial dye concentration, and contact time. Outcomes reveal EC's superiority in dye removal compared to TA. As a bioremediation agent, EC exhibits a 90.46% removal efficacy for MB within 15 min, with pH 7.0 as the operative condition. Equilibrium analysis employs Temkin (T), Freundlich (F), and Langmuir (L) isotherms, revealing an excellent fit with the L isotherm model. The study delves further by probing surface adsorption kinetics through pseudo-first-order (PFO) and pseudo-second-order (PSO) models. Furthermore, to discern the divergent impacts of EC and TA on soil heavy metal reduction, soil samples were collected from three distinct zones: an untouched control area, alongside areas where EC and TA were cultivated at the Yazd wastewater site in Iran. Heavy metal levels in the soil were meticulously assessed through rigorous measurement and statistical scrutiny. The findings spotlight TA-cultivated soil as having the highest levels across all examined factors. Ultimately, EC emerges as the superior contender, proficiently excelling in both MB eliminations from wastewater and heavy metal amelioration in the soil, positioning it as the preferred phytoremediation agent.

Enhancing catalyst stability: Immobilization of Cu-Fe catalyst in sodium alginate matrix for methyl orange removal via Fenton-like reaction

This study aims to enhance the stability and effectiveness of heterogeneous catalysts in Fenton-like reactions, explicitly addressing the acidity limitations inherent in traditional Fenton processes. Copper-iron was synthesized through co-precipitation, and a catalyst bead was produced from hydrogel formation. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) confirm phases in the bimetallic Copper-iron, aligning with the intended composition. Modification with alginate led to reduced metal leaching compared to the bare bimetallic counterpart, as confirmed by atomic absorption spectroscopy (AAS). Additionally, Fourier-transform infrared spectroscopy (FTIR) revealed the deactivation of alginate through the disappearance of carboxyl groups, indicating the depolymerization of the catalyst bead. Under the suggested conditions (Methyl Orange concentration of 25 mg/L, initial solution pH of 7, 2 g/L catalyst loading, concentration of hydrogen peroxide 100 mM in a 120-min reaction time), the catalyst demonstrated remarkable decolorization efficiency of Methyl Orange, achieving 97.67 %. Further highlighting its practicality, the catalyst exhibited outstanding reusability over four cycles under identical conditions, showcasing robust immobilization capabilities and sustained performance. Notably, the catalyst's magnetic properties facilitated easy separation using an external magnet. In conclusion, the developed catalyst beads offer a solution with high reusability, magnetic separability, and reduced iron leaching. The advantageous characteristics underscore its potential as a heterogeneous catalyst for wastewater treatment applications, warranting further exploration under practical conditions.

Enhancing the adsorption capacity of organic and inorganic pollutants onto impregnated olive stone derived activated carbon

This study presents a sustainable approach to activated carbon production from olive stones in comparison to commercial ones, using various activating agents such as H3PO4, KOH, and ZnCl2, for enhancing the adsorption properties and versatile adsorption capability to remove a range of pollutants including copper ion, methylene blue, and 2,4-Dichlorophenoxyacetic acid from aqueous solutions. The performances of activated carbons across varying conditions such as pollutant concentrations, temperatures, pH levels, and adsorbent amounts were tested. Increased initial pollutant concentrations correlated with higher adsorption capacities. Maximum adsorption capacities were achieved at pH levels of 5, 10, and 2 for Cu, MB, and 2,4-D, respectively. For KOSAC, Cu removal rose from 27 % to 52 %, for ZOSAC, MB removal increased from 39 % to 65 %, and for ZOSAC, 2,4-D removal surged from 33 % to 99 % at varying adsorbent amounts. Model validation was carried out utilizing the kinetic models (PFO, PSO) and isotherm models (Langmuir, Redlich-Peterson). The PFO kinetic model and Langmuir isotherm model proved more suitability for Cu adsorption, whereas PFO and PSO kinetic models, along with Redlich-Peterson isotherm models, were more prominent for MB and 2,4-D adsorption. Thermodynamic analysis revealed that the adsorption of Cu and 2,4-D was exothermic, while MB adsorption was endothermic. By optimization of experimental conditions, the maximum adsorption capacities were attained at 30.34 °C and 297.65 mg L-1 for KOSAC-Cu, 48.62 °C and 269.37 mg L-1 for ZOSAC-MB, and 30.31 °C and 299.02 mg L-1 for ZOSAC-2,4-D sorption. This research highlights ZOSAC's potential as a cost-effective, eco-friendly solution for water treatment, contributing to environmental sustainability and economical feasibility.

Application of coal fly ash for trace metal adsorption from wastewater: A review

Environmental pollution has become a global issue due to continuing anthropogenic activities that result in the production of enormous amounts of waste and the subsequent release of hazardous trace metals. The increasing levels of trace metals in the environment must be monitored regularly and reduced to prevent contamination of food chain. Numerous conventional technologies that are widely used for the removal of trace metals from environmental matrices have many drawbacks. Currently, the preferred method to remove trace metal ions is the adsorption process, which normally uses adsorbents. This review investigated the applications of coal fly ash (CFA) as a cost-effective adsorbent and the role it plays in the improved properties of nanomaterials that are used for treatment of trace metals in water. The use of CFA and its role in chemical modification processes results to high removal efficiency of trace metals. CFA is a by-product of coal combustion which is available in abundance and therefore its use is not only beneficial in water treatment processes, but also reduce the burden of solid waste disposal.

Blended Nephelium lappaceum and Durio zibethinus wastes for activated carbon production via microwave-ZnCl2 activation: optimization for methylene blue dye removal

Herein, this work targets to employ the blended fruit wastes including rambutan (Nephelium lappaceum) peel and durian (Durio zibethinus) seed as a promising precursor to produce activated carbon (RPDSAC). The generation of RPDSAC was accomplished through a rapid and practical procedure (microwave-ZnCl2 activation). To evaluate the adsorptive capabilities of RPDSAC, its efficacy in eliminating methylene blue (MB), a simulated cationic dye, was measured. The Box-Behnken design (BBD) was utilized to optimize the crucial adsorption parameters, namely A: RPDSAC dose (0.02-01 g/100 mL), B: pH (4-10), and C: time (2-6 min). The BBD design determined that the highest level of MB removal (79.4%) was achieved with the condition dosage of RPDSAC at 0.1 g/100 mL, contact time (6 min), and pH (10). The adsorption isotherm data is consistent with the Freundlich concept, and the pseudo-second-order versions adequately describe the kinetic data. The monolayer adsorption capacity (qmax) of RPDSAC reached 120.4 mg/g at 25 °C. Various adsorption mechanisms are involved in the adsorption of MB dye onto the surface of RPDSAC, including π-π stacking, H-bonding, pore filling, and electrostatic forces. This study exhibits the potential of the RPDSAC as an adsorbent for removal of toxic cationic dye (MB) from contaminated wastewater.

Prediction and optimizing of methylene blue sequestration to activated charcoal/magnetic nanocomposites using artificial neutral network and response surface methodology

Green synthesized magnetic nanoparticles (MNPs) linked with activated charcoal (AC) (AC/Fe3O4 NCs) were exploited for methylene blue (MB) confiscation in this study. The AC/Fe3O4 NCs produced were characterized using TEM, FTIR, UV/Vis and XRD spectrometry. The Response-Surface-Methodology (RSM) was utilized to improve the experimental data for the MB sorption to AC/Fe3O4 NCs, with 20 experimental runs implemented through a central composite design (CCD) to assess the effect of sorption factors-initial MB concentration, pH and sorbent dosage effects on the response (removal-effectiveness). The quadratic model was discovered to ideally describe the sorption process, with an R2 value of 0.9857. The theoretical prediction of the experimental data using the Artificial-Neural-Network (ANN) model showed that the Levenberg-Marquardt (LM) had a better performance criterion. Comparison between the modelled experimental and predicted data showed also that the LM algorithm had a high R2 of 0.9922, which showed NN model applicability for defining the sorption of MB to AC/Fe3O4 NCs with practical precision. The results of the non-linear fitting (NLF) of both isotherm and kinetic models, showed that the sorption of MB to AC/Fe3O4 NCs was perfectly described using the pseudo-second-order (PSOM) and Freundlich (FRHM) models. The estimated optimum sorption capacity was 455 mg g-1. Thermodynamically, the sorption of MB to AC/Fe3O4 NCs was shown to be non-spontaneous and endothermic.

Exploring the structural characteristics and dye removal capabilities of powder-, granule- and film- shaped magnetic activated carbon derived from Oleaster seed

Dye pollution in water caused by excessive discharge of industrial effluent has become a major environmental problem in recent decades because of its irreversible effects on human health. In this study, low-cost carbon-based adsorbents synthesized from Oleaster seed (OS) were prepared in three forms of powder (PAC), film (FAC), and granule (GAC) and used for the removal of methylene blue dye. The properties of the synthesized adsorbents were characterized by SEM-EDX, BET, XPS and FTIR analyses. The maximum adsorption capacity (qmax) of PAC, FAC, and GAC adsorbents were obtained as 68.49, 32.25, and 15.10 mg/g, respectively at the optimum experimental conditions of pH = 10, adsorbent dosages of 0.5, 1, and 2 g/l, contact times of 60, 90, and 120 min, dye concentration of 10 mg/L, and temperature of 25°C. The Langmuir isotherm well described the equilibrium data for all three adsorbents. The pseudo-second-order kinetic model provided the best fit with the adsorption data obtained from all three adsorbents. Adsorption occurred spontaneously through a combination of chemical and physical mechanisms, with a thermodynamically exothermic process. The desorption experiments demonstrated that all the adsorbents have substantial potential for recovery. The novel activated carbon/alginate composite films are proposed as more promising biosorbents to remove MB dye from the aquatic environment compared to GAC adsorbents.

A review on sustainable management of biomass: physicochemical modification and its application for the removal of recalcitrant pollutants-challenges, opportunities, and future directions

Adsorption is one of the most efficient methods for remediating industrial recalcitrant wastewater due to its simple design and low investment cost. However, the conventional adsorbents used in adsorption have several limitations, including high cost, low removal rates, secondary waste generation, and low regeneration ability. Hence, the focus of the research has shifted to developing alternative low-cost green adsorbents from renewable resources such as biomass. In this regard, the recent progress in the modification of biomass-derived adsorbents, which are rich in cellulosic content, through a variety of techniques, including chemical, physical, and thermal processes, has been critically reviewed in this paper. In addition, the practical applications of raw and modified biomass-based adsorbents for the treatment of industrial wastewater are discussed extensively. In a nutshell, the adsorption mechanism, particularly for real wastewater, and the effects of various modifications on biomass-based adsorbents have yet to be thoroughly studied, despite the extensive research efforts devoted to their innovation. Therefore, this review provides insight into future research needed in wastewater treatment utilizing biomass-based adsorbents, as well as the possibility of commercializing biomass-based adsorbents into viable products.

Advancements in Olive-derived Carbon: Preparation Methods and Sustainable Applications

In the realm of material science, carbon materials, especially olive-derived carbon (ODC), have become vital due to their sustainability and diverse properties. This review examines the sustainable extraction and use of ODC, a carbohydrate-rich by-product of olive biomass. We focus on innovative preparation techniques like pyrolysis, which are crucial forenhancing ODC's microstructure and surface properties. Variables such as activating agents, impregnation ratios, and pyrolysis conditions significantly influence these properties. ODC's high specific surface area renders it invaluable for applications in energy storage (batteries and supercapacitors) and environmental sectors (water purification, hydrogen storage). Its versatility and accessibility underscore its potential for broad industrial use, makingit as a key element in sustainable development. This review provides a detailed analysis of ODC preparation methodologies, its various applications, and its role in advancing sustainable energy solutions. We highlight the novelty of ODC research and its impact on future studies, establishing this review as a crucial resource for researchers and practitioners in sustainable carbon materials. As global focus shifts towards eco-friendly solutions, ODC emerges as a critical component in shaping a sustainable, innovation-driven future.

Enhanced adsorption of phenolic compounds using biomass-derived high surface area activated carbon: Isotherms, kinetics and thermodynamics

The progress of industrial and agricultural pursuits, along with the release of inadequately treated effluents especially phenolic pollutant, has amplified the pollution load on environment. These organic compounds pose considerable challenges in both drinking water and wastewater systems, given their toxicity, demanding high oxygen and limited biodegradability. Thus, developing an eco-friendly, low-cost and highly efficient adsorbent to treat the organic pollutants has become an important task. The present investigation highlights development of a novel adsorbent (CFPAC) by activation of Cassia fistula pod shell for the purpose of removing phenol and 2,4-dichlorophnenol (2,4-DCP). The significant operational factors (dosage, pH, concentration, temperature, speed) were also investigated. The factors such as pH = 2 and T = 20°C were found to be significant at 1.6 g/L and 0.6 g/L dosage for phenol and 2,4-DCP respectively. Batch experiments were further conducted to study isotherms, kinetic and thermodynamics studies for the removal of phenol and 2,4-DCP. The activated carbon was characterised as mesoporous (specific surface area 1146 m2/g, pore volume = 0.8628 cc/g), amorphous and pHPZC = 6.4. At optimum conditions, the maximum sorption capacity for phenol and 2,4-DCP were 183.79 mg/g and 374.4 mg/g respectively. The adsorption isotherm was better conformed to Redlich Peterson isotherm (phenol) and Langmuir isotherm (2,4-DCP). The kinetic study obeyed pseudo-second-order type behaviour for both the pollutants with R2 > 0.999. The thermodynamic studies and the value of isosteric heat of adsorption for both the pollutants suggested that the adsorption reaction was dominated by physical adsorption (ΔHx < 80 kJ/mol). Further, the whole process was feasible, exothermic and spontaneous in nature. The overall studies suggested that the activated carbon synthesised from Cassia fistula pods can be a promising adsorbent for phenolic compounds.

Anionic dye removal by immobilized bacteria into alginate-polyvinyl alcohol-bentonite matrix

Methyl orange (MO) is commonly used in the textile dyeing industry, posing serious health and environmental hazards due to its carcinogenic, mutagenic properties, and potential for bioaccumulation. Appropriate handling is needed to solve these problems by harnessing the capacity of living microorganisms and the adsorption properties of bentonite clay minerals. Although the conventional approach predominantly depends on free cells, recent study has developed other methods such as immobilization techniques. Therefore, this study aimed to investigate the efficiency of the immobilization matrix comprising sodium alginate (SA), polyvinyl alcohol (PVA), and bentonite by modifying Pseudomonas aeruginosa, Bacillus subtilis, and Ralstonia pickettii for MO removal of 50 mg/L. In the free cell technique, the results showed that the MO decreased to 43.13, 36.61, and 27.45% for each of the bacteria within 10 days at 35 °C. The bacterial immobilization technique, including live immobilized P. aeruginosa (LIPa), live immobilized B. subtilis (LIBs), and live immobilized R. pickettii (LIRp) beads also demonstrated significant efficiency, achieving MO removal rates up to 97.15, 95.65, and 66.63% within 10 days. These synthesized beads showed reusability, with LIPa, LIBs, and LIRp being used up to 4, 4, and 2 cycles, respectively. The external and internal surface conditions were observed using SEM instrument and the results showed that all components were agglomerated. Comparisons using dead bacterial biomass indicated that treatment with live bacteria consistently yielded significantly higher removal rates. These results showed the effectiveness of immobilized bacteria in MO removal, offering a promising potential in reducing pollutants.

Highly efficient catalytic degradation of organic dyes using iron nanoparticles synthesized with Vernonia Amygdalina leaf extract

Today, nanoscience explores the potential of nanoparticles due to their extraordinary properties compared to bulk materials. The synthesis of metal nanoparticles using plant extracts is a very promising method for environmental remediation, which gets global attention due to pollution-led global warming. In the present study, iron nanoparticles (FeNPs) were successfully synthesized by the green method using Vernonia amygdalina plant leaf extract as a natural reducing and capping agent. Biosynthesized FeNPs were characterized with different analytical techniques such as UV-visible, FT-IR, XRD, and SEM. The analysis revealed the formation of amorphous FeNPs with an irregular morphology and non-uniform distribution in size and shape. The average particle size was approximately 2.31 µm. According to the catalytic degradation investigation, the FeNPs produced via the green approach are highly effective in breaking down both CV and MB into non-toxic products, with a maximum degradation efficiency of 97.47% and 94.22%, respectively, when the right conditions are met. The kinetics study exhibited a high correlation coefficient close to unity (0.999) and (0.995) for the degradation of MB and CV, respectively, for the zero-order pseudo-kinetics model, which describes the model as highly suitable for the degradation of both dyes by FeNPs compared to other models. The reusability and stability of biosynthesized nano-catalysts were studied and successfully used as efficient catalysts with a slight decrease in the degradation rate more than four times. The results from this study illustrate that green synthesized FeNPs offer a cost-effective, environmentally friendly, and efficient means for the catalytic degradation of organic dyes.

Removal of textile pollutants from aqueous medium using biosynthesized CuO nanoparticles: Theoretical comparative investigation via analytical model

The work deals with the removal of two dyes, namely methylene blue (MB) and methyl orange (MO), from polluted water by adsorption onto CuO nanoparticles synthesized with a green synthesis procedure, starting from plant resources. Adsorption isotherms are determined at different temperatures aiming at investigating the adsorption mechanisms of the two dyes. The experimental results indicate that, for both MB and MO, the adsorption capacity increases with increasing temperature, with slight differences in the case of MO. Comparatively, the CuO nanoparticles show a higher MB adsorption capacity with respect to MO. A modelling analysis is carried out with a multilayer model derived from statistical physics, selected among a group of models, each hypothesizing a different number of adsorbed molecules layers. The analysis of model parameters allows determining that the adsorbate molecules exhibit a non-parallel orientation on the surface of biosynthesized CuO nanoparticles and each functional group of the adsorbent binds multiple molecules, simultaneously.The model also allows determining the number of dye molecule layers formed on adsorbent surface, in all the cases resulting higher than three, also confirming the effect of temperature on the maximum adsorption capacity.Specifically, the total number of dye layers formed on biosynthesized CuO nanoparticles surface exhibited a range of 4.17-4.55 for MB dye and of 3.01-3.51 for MO dye.Finally, the adsorption energies reveal that adsorption likely involves physical forces (all resulting all below 22 kJ/mol), i.e. hydrogen bonding and van der Waals forces. The adsorption energies for the interactions between dye molecules are lower than those calculated for the interactions between the dye molecules and the adsorbent surface.

Revealing the interface chemistry of polyaniline grafted biomass via statistical modeling of multi-component dye systems: optimization, kinetics, thermodynamics, and adsorption mechanism

The growing need to examine the adsorption capabilities of innovative materials in real-world water samples has encouraged a shift from single to multicomponent adsorption systems. In this study, a novel composite, PANI-g-SM was synthesized by covalently grafting a lignocellulosic biomass, Saccharum munja (SM) with polyaniline (PANI). The as-synthesized composite was investigated for the simultaneous adsorption of cationic (Methylene Blue (MB); Crystal Violet (CV)) and anionic dyes (Reactive Red 35 (RR); Fast Green FCF (FG)) from four single components and two binary systems, MB + RR and CV + FG. Further, the effect and interaction of pH (2-11), dosage (0.01-0.04 g/10 mL), and initial concentration (0.0313 to 0.1563 mmol/L) on the elimination of dyes by PANI-g-SM were studied through a novel design of Box-Behnken of Response Surface Methodology (RSM) technique which was found to be highly useful for revealing the chemistry of interfaces in multi-component systems. The extended Langmuir model for the binary system indicated the presence of synergism, as result the maximum monolayer adsorption capacity increased by 44.44%, 645.83%, 67.88%, and 441.07% for MB, RR, CV, and FG dye, respectively. Further, the adsorption process mainly followed a pseudo-second-order kinetic model, and the thermodynamic studies revealed the exothermic nature of adsorption for RR and FG dye while endothermic for MB and CV dye, respectively with Δ G varying from - 1.68 to - 6.12 kJ/mol indicating the spontaneity of the process. Importantly, the efficacy of the composite was evaluated for the treatment of textile industry effluent highlighting its potential as an adsorbent for wastewater treatment.

Expermental investigation on adsorption of methylene blue dye from waste water using corncob cellulose-based hydrogel

Hydrogel from corncob cellulose was synthesized in this investigation. The synthesized Hydrogel was characterized by SEM, XRD, and FTIR instruments. As the results indicate the synthesized hydrogel has required and important features, these suggest the suitability of hydrogel for the adsorption of methylene blue dye (MBD). Three important process variables (dosage, contact time, and initial concentration) with three levels were studied during the adsorption process at 30 °C and neutral pH. The efficiency of hydrogel for adsorption of MBD was determined in each experiment. The experimental results were statistically analyzed and interpreted. The maximum removal efficiency was achieved at 2.22 g/L of dosage, 80.36 min of contact time, and 74.54 mg/L of initial concentration. At this condition, 98.25% of MBD was achieved through experimental tests. Kinetics, isotherm, and thermodynamics studies were performed. Langmuir isotherm is more suitable to describe the adsorption process and the Pseudo second-order kinetic model fits this process. From the thermodynamics studies, all negative values of change in Gibbs free energy (ΔG°), and positive value of change in enthalpy (ΔH°), and change in entropy (ΔS°) indicate that the carried out experimental process is a spontaneous and endothermic. Moreover, the regeneration experiment for adsorbent was performed. The treatment of real textile industry waste water was conducted and the removal efficiency of hydrogel was 64.76%. This removal percentage reduction from sythetic aqueous solution is due to involvement of other pollutants in the real waste water. The synthesized hydrogel adsorbent is suitable up to the third cycle without significant loss in removal efficiency.

Conversion of carbon black recovered from waste tires into activated carbon via chemical/microwave methods for efficient removal of heavy metal ions from wastewater

In this research study, recovered carbon black (rCB) was obtained via pyrolysis of waste tires. The obtained rCB was then converted into activated carbon species through both chemical treatment and microwave coupled with chemical treatment as a two-step activation process. The activated carbon obtained from chemical activation was denoted as C-AC, while that obtained from exposure to microwave followed by chemical activation was labeled as MC-AC. These two structures were consequently introduced as sorbents for the removal of cadmium ions from an aqueous solution. The structural characteristics of the introduced adsorbents were confirmed using various techniques, namely X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray (EDX) spectroscopy. Additionally, textual features of these adsorbents were acquired via both scanning electron microscopy (SEM) and N2 adsorption-desorption BET surface area analyses. These two structures were then introduced for Cd ion adsorption under different operating conditions. Particularly, the effect of pH, contact time, adsorbent dose, and metal ion concentration on the efficiency of adsorption was investigated. The 1maximum adsorption capacity was detected at a pH value of 5.0, a contact time of 30 min, a sorbent dose of 0.4 g L-1, and an initial metal concentration of 50 mg L-1 using MC-AC, which exhibited nearly double the sorption capacity detected for C-AC. Kinetic studies indicated that the process of Cd(ii) adsorption is perfectly described and fitted by the pseudo-second-order model. However, adsorption isotherms for the two adsorbents were found to match the Langmuir model, referring to the occurrence of uniform monolayer adsorption for the metal ions. Thermodynamic analysis demonstrated that the adsorption process was spontaneous and endothermic.

High surface area activated carbon from a pineapple (ananas comosus) crown via microwave-ZnCl2 activation for crystal violet and methylene blue dye removal: adsorption optimization and mechanism

In this investigation, microwave irradiation assisted by ZnCl2 was used to transform pineapple crown (PN) waste into mesoporous activated carbon (PNAC). Complementary techniques were employed to examine the physicochemical characteristics of PNAC, including BET, FTIR, SEM-EDX, XRD, and pH at the point-of-zero-charge (pHpzc). PNAC is mesoporous adsorbent with a surface area of 1070 m2/g. The statistical optimization for the adsorption process of two model cationic dyes (methylene blue: MB and, crystal violet: CV) was conducted using the response surface methodology-Box-Behnken design (RSM-BBD). The parameters include solution pH (4-10), contact time (2-12) min, and PNAC dosage (0.02-0.1 g/100 mL). The Freundlich and Langmuir models adequately described the dye adsorption isotherm results for the MB and CV systems, whereas the pseudo-second order kinetic model accounted for the time dependent adsorption results. The maximum adsorption capacity (qmax) for PNAC with the two tested dyes are listed: 263.9 mg/g for CV and 274.8 mg/g for MB. The unique adsorption mechanism of MB and CV dyes by PNAC implicates multiple contributions to the adsorption process such as pore filling, electrostatic forces, H-bonding, and π-π interactions. This study illustrates the possibility of transforming PN into activated carbon (PNAC) with the potential to remove two cationic dyes from aqueous media.

Preparation of cationic surfactant modified two-dimensional (2D) multi-layered Ti3C2Tx MXene for methyl orange removal from aqueous solution: Kinetic, equilibrium, and adsorption mechanisms

In this study, cetyltrimethylammonium bromide-modified multi-layered Ti3C2Tx MXene (CMM) was produced using a Ti3AlC2 precursor, and its capacity to remove the anionic dye, methyl orange (MO), was investigated in detail. An electrostatic combination between negatively charged Ti3C2Tx nanosheets and cationic surfactant solution (CTAB) produced this adsorbent. This triggered an exposure of the accessible active sites to further boost adsorption effectiveness by increasing the distance between the MXene nanosheets. Prepared adsorbents were characterized using some analytical techniques, including TGA, FESEM, EDX, FTIR, XRD, and N2 adsorption-desorption. Furthermore, some influencing parameters such as contact time, solution of pH, loading adsorbent, and initial dye concentration were evaluated, with findings showing that MO could adsorb CMM to its maximum capacity at an adsorbent dosage of 0.83 g/L, a contact time of 90 min, and a solution pH of 3. Adsorption results were found to be highly linked with both Langmuir isotherm (R2 = 0.9990) and the pseudo-second-order kinetic model (R2 = 0.9924). The maximum adsorption capacity of MO was obtained at approximately 213.00 mg/g. Also, hydrogen bonding, π-cation interactions, and electrostatic adsorption can all be implicated in the mechanism of MO adsorption on CMM. The fabricated CMM is presented as a prospective adsorbent for the removal of dyes from polluted water, demonstrating robust recyclability for up to the fifth iteration. All these outstanding properties indicate that cetyltrimethylammonium bromide-modified multi-layered Ti3C2Tx MXene can be considered as applicable adsorbents for textile pollutants.

Graphene oxide nanosheets immobilised on honeycomb pore structure of pomelo peel for enhanced removal of methylene blue

Herein, for the first time, a simple, green, direct immersion immobilisation method is reported for graphene oxide (GO) nanosheets using pomelo peel (PL) as a substrate. A GO/PL porous sponge was successfully prepared and used to remove methylene blue (MB) from dye wastewater. Considering the porosity, hydrophilicity and elasticity of the PL, the PL was placed in a GO aqueous suspension through direct immersion immobilisation. The carboxyl and hydroxyl groups in the peel could effectively capture and immobilise the GO nanosheets. GO was adsorbed into the PL pores and dispersed throughout the PL. Finally, the prepared super-hydrophilic and elastic GO/PL exhibited excellent adsorption performance towards MB in dye wastewater. The adsorption results revealed that the adsorption behaviour was consistent with the Langmuir isotherm and quasi-secondary kinetic models. The maximum equilibrium adsorption capacity of GO/PL towards MB was 124.2 mg/g, exceeding the values obtained for most of the previously reported adsorbents. Moreover, after five consecutive adsorption-desorption cycles, GO/PL retained 75% of its initial adsorption capacity. Mechanistic analysis revealed that pore filling, electrostatic attraction, ion exchange and hydrogen bonding interactions are the primary driving forces facilitating MB adsorption.

Synthesis & fabrication of O-linked polymeric hybrids for recovery of textile dyes: Closed loop economy

Dyes are an important resource employed for the production systems in textile, paper, paint and leather industry. An estimate of 200,000 tons of dyes are discharged as textile effluent each year worldwide. It becomes imperative to recover these dyes by treating the effluents using economically viable routes. The present research was undertaken with the objective to attain zero emission and zero waste through development of novel polymeric hybrids as adsorbents. For this purpose, metal moieties (Al3+, Si4+, Ti4+ and Zr4+) were hybridized with polyacrylic acid, and cellulose acetate for the uptake of selected dyes under optimized parameters. The structural elucidation of four synthesized hybrids (MP-Al, MP-Si, MP-Ti and MP-Zr) by FTIR, EDX and TGA confirmed O-linked grafting of metal moieties with polymers and thermally stable porous materials. SEM micrographic images displayed void spaces providing channels for effective adsorption. The batch experiments demonstrated removal of malachite green (77-96%) and congo red (70-82%) upon contact of initial 45 min on polymeric hybrids On the other hand, pristine polyacrylic acid and cellulose acetate showed remarkably low removal of dyes. The adsorption mechanism is proposed as physical in nature following type II isotherm. Further, Langmuir and Ho's pseudo second order fitness was evaluated. In order to determine the economic viability of the present research, the real textile dyes were recovered in three consecutive cycles of adsorption and chemical treatment of hybrids. The results propose a system with positive impact on economy by maximum utilization of hybrids as adsorbents and recovery of textile dyes for reuse in textile processing.

Cd2+ Detection by an Electrochemical Electrode Based on MWCNT-Orange Peel Activated Carbon

This study reports the development of a new electrochemical sensor based on a carbon paste electrode (CPE) composed of biomass-based orange peel activated carbon (ACOP) and multiwalled carbon nanotubes (MWCNTs), and this composite is used for the electrochemical detection of cadmium ions (Cd2+). The ACOP/MWCNT composite was characterized by FTIR, Raman, and electrochemical impedance spectroscopy. The electrochemical evaluation of Cd2+ was performed using square wave and cyclic voltammetry. The ACOP/MWCNT-CPE electrochemical sensor exhibited a coefficient of determination r2 of 0.9907, a limit of detection of 0.91 ± 0.79 μmol L-1, and a limit of quantification of 3.00 ± 2.60 μmol L-1. In addition, the developed sensor can selectively detect Cd2+ in the presence of different interferents such as Zn2+, Pb2+, Ni2+, Co2+, Cu2+, and Fe2+ with a relative standard deviation (RSD) close to 100%, carried out in triplicate experiments. The ACOP/MWCNT-CPE presented high sensitivity, stability, and reproducibility and was successfully applied for the detection of Cd2+ in river water samples with recovery rate values ranging from 97.33 to 115.6%, demonstrating to be a very promising analytical alternative for the determination of cadmium ions in this matrix.

Microwave Heating for Synthesis of Carbonaceous Adsorbents for Removal of Toxic Organic and Inorganic Contaminants

The residues obtained from the extraction of Inonotus obliquus fungus were used to produce carbonaceous adsorbents. The initial material was subjected to pyrolysis in a microwave oven. The adsorbents were characterized through elemental analysis, low-temperature nitrogen adsorption/desorption isotherms, and Boehm titration. The carbonaceous adsorbents were tested for the removal of NO2, methylene blue, and malachite green. The results indicated that the obtained carbonaceous adsorbents exhibited basic characteristics and possessed specific surface areas of 372 and 502 m2/g. The adsorption process of liquid contaminants was modeled using the single-layer Langmuir model. The maximum adsorption capacities were found to be 101 and 109 mg/g for methylene blue, and 75 and 77 mg/g for malachite green. The kinetic study demonstrated that the adsorption of methylene blue and malachite green was better described by a pseudo-second order model. The study affirmed that the adsorption of organic dyes onto the resultant carbonaceous adsorbents was both spontaneous and endothermic. The study also demonstrated that the presence of an air stream during the NO2 adsorption process and prehumidization of the adsorbent with humid air had a beneficial effect on the obtained sorption capacities. In conclusion, the study demonstrated that pyrolysis of the extraction residues from the fungus Inonotus obliquus yields highly effective, environmentally friendly, and cost-efficient carbonaceous adsorbents for the removal of both gaseous and liquid pollutants.

Investigation on Methylene Blue Dye Adsorption in Aqueous by the Modified Mussel Shells: Optimization, Kinetic, Thermodynamic and Equilibrium Studies

This study assessed the methylene blue adsorption using natural and modified mussel shell powders in the aqueous solution. The mussel shell samples were processed in a NaClO solution then modified with sodium dodecyl sulfate and ethylenediaminetetraacetic acid. The characteristics of mussel shell samples before and after modification were demonstrated using infared spectroscopy, thermogravimetric analysis, scanning electron microscopy, nitrogen adsorption/desorption, energy dispersive X-ray, water contact angle, and dynamic light scattering methods. Some factors such as the pH of the medium, adsorption temperature, and adsorption time had a significant effect on the methylene blue adsorption of mussel shell samples. The adsorption isotherm models and kinetics of methylene blue adsorption by mussel shell samples were also studied. A quadratic regression equation was selected with experimental planning following the Box-Behnken model combined with Design Expert 11.1.0.1 software to optimize the methylene blue adsorption process by mussel shell samples. These results open a promising direction for using naturally derived materials to remove organic pollutants from contaminated water.

Effective removal of malachite green from local dyeing wastewater using zinc-tungstate based materials

The frequent use of an industrial dye such as malachite green (MG) has caused major water body deterioration and is one of the most pressing global challenges, demanding effective treatment techniques. To solve these issues, a simplistic method was developed to synthesize zinc-tungstate (ZnWO4) nanoparticles and also dope the surface matrix of the ZnWO4 nanoparticles using nonmetals of boron (B), carbon (C), and nitrogen (N) at different ratios for enhanced MG removal from wastewater. The prepared nanomaterials were characterized by different methods for crystal structure composition, surface properties, surface morphology, microstructures, functional groups, and elemental oxidation states. The BET analysis revealed a mesoporous structure with surface areas of 30.740 m2/g for ZnWO4, 38.513 m2/g for ZnWO4@BCN, 37.368 m2/g for ZnWO4@BCN/B, 39.325 m2/g for ZnWO4@BCN/C, and 45.436 m2/g for ZnWO4@BCN/N nanocomposites. The best removal of MG was accomplished at pH (8), contact period (50 min), nanoadsorbent dose (0.8 g/L), initial MG concentration (20 mg/L), and temperature (303 K). The maximum adsorption capacities of ZnWO4 and ZnWO4@BCN/N towards MG were 218.645 and 251.758 mg/g, respectively. At equilibrium, the Freundlich isotherm and pseudo-second-order kinetic models were the best fits for the experimental data of MG adsorption on both nanoadsorbents. After eight cycles of adsorption and desorption, both ZnWO4 and ZnWO4@BCN/N were found to be good at removing MG, with efficiencies of 71.00 and 74.20%, respectively. Thermodynamic investigations further validated the spontaneity and endothermic nature of the adsorption process. All study findings confirm the nanoadsorbents exceptional capability and economic feasibility for removing MG dye.

Development and optimization of geopolymer adsorbent for water treatment: Application of mixture design approach

The current paper refers to the study of a new approach to optimizing the adsorptive properties of geopolymers by varying the aluminosilicate precursors from kaolin (K), metakaolin (MK), and coal fly ash (CFA) as internal synthesis factors. The simplex-augmented-centroid mixture design was applied to identify the optimal formulation from the three aluminosilicate precursors to develop a geopolymer (GP) with a distinctive structure that positively affects its dye adsorption efficiency. The variously formulated GP samples were tested for the removal of both methylene blue (MB-dye) and crystal violet dye (CV-dye) from an aqueous solution. The mathematical-statistical analysis of the experimental readings suggested that the generated special cubic models were significant, and thus the chosen approach was adequate for determining the optimum blending proportion. The optimization tools indicated that the optimal mixture from the three aluminosilicate precursors for developing a GP with high adsorption efficiency was 58% MK, 42% K, and 0% CFA. The optimized geopolymer (GP_O) was synthesized and then analyzed using a variety of physicochemical techniques, which revealed the presence of an amorphous N-A-S-H gel-rich porous structure as an influencing property on the geopolymer's organic dye adsorption efficiency. The dependence of the adsorption mechanism of both MB-dye and CV-dye by GP_O on the adsorbent dosage, contact time, initial dye concentration, temperature, and solution pH was evaluated. The isothermic and kinetic experimental readings for MB and CV-dyes adsorption by GP_O were well fitted to the pseudo-second-order and Freundlich models, with an exothermic, favorable, and spontaneous adsorption reaction thermodynamically. The experimental studies in the lab scale on GP_O produce comparable results. From these results, it has been concluded that the accuracy and feasibility of the mixture design simulation succeeded in optimizing and developing a geopolymeric sorbent material with great potential as an excellent economical agent for removing cationic dyes from aqueous media. This point represents an added value compared to traditional non-optimized geopolymer absorbents. Besides, this geopolymer material represents a significant application possibility for water treatment and remediation of hazardous dye pollutants.

Potential of agro-industrial residues from the Amazon region to produce activated carbon

Thousands of tons of residual lignocellulosic biomass are produced and discarded by agroindustries in the Amazon. These biomasses could be harnessed and used in the preparation of activated carbon, in view of the growing demand for this product with high added value, however, little is known about their characteristics, in addition to their potential as precursors of activated carbon. Therefore, the aim of this work was to evaluate the potential of four different biomasses in the preparation and quality of activated carbon. Residues from the processing of the fruits of acai, babassu, Brazil nut, and oil palm were collected, characterized, carbonized, physically activated with CO₂, and characterized. The contents of the total extractives, insoluble lignin, minerals, holocellulose, and elemental (CHNS-O) were analyzed. The surface area and surface morphology were determined from the AC produced, and adsorption tests for methylene blue and phenol were performed. The four biomasses showed potential for use in the preparation of CA; the residues presented high contents of lignin (21.83-55.76%) and carbon (46.49-53.79%). AC were predominantly microporous, although small mesopores could be observed. The AC had a surface area of 569.65-1101.26 m² g^-1, a high methylene blue (93-390 mg g^-1), and phenol (159-595 mg g^-1) adsorption capacities. Babassu-AC stood out compared to the AC of the other analyzed biomasses, reaching the best results.

Investigating mixed biosolids and cardboard for methylene blue adsorption: Activation, adsorption modelling and thermodynamics

Ongoing global population boom has led to the rise in waste and related research on increasing its economic value. In such an attempt, this study aims to activate gas-to-liquids (GTL) derived biosolids (BS) and cardboard (CB) and mixed samples (50:50) using potassium carbonate to produce three activated carbons (ACs): KBS, KCB and KM respectively. The characterization of the samples revealed surface areas of 156, 515, and 527 m²/g for KBS, KCB, and KM, respectively based on Brunauer-Emmett-Teller (BET) analysis, with increased porosity and metal content after activation evident from the Scanning Electron Microscopy-Energy Dispersive Spectroscopy (SEM-EDS) results, as well as the presence of magnetite in the KBS and KM samples apparent from the X-ray powder diffraction (XRD) results. Additionally, Fourier Transform Infrared Spectroscopy (FTIR) results indicate increased C-O-C stretches and O-H bonds after activation of the samples. The ACs were used for methylene blue (MB) removal process which is a rapid for all three samples, reaching equilibrium after 9 h, and optimal at neutral pH and maximum at the highest temperature, 40 °C. The MB adsorption capacity was highest for KM (191.07 mg/g), followed by the KCB and KBS samples. Isotherm modelling of the samples showed best fits for KBS, KCB and KM as Langmuir-Freundlich (LF), Langmuir and Toth models respectively. On the contrary, kinetic modelling using contact time study data for all samples exhibited best fits by the Diffusion-chemisorption (DC) model. Finally, the thermodynamic calculations of the mixed sample disclosed the adsorption process to be exothermic and spontaneous, with potential mechanisms being electrostatic attraction, ion exchange, π-π interactions, and hydrogen bonding. Multiple cycles of KM regeneration was also achieved with good adsorption capacities. Future work will explore other activation methods and examine the magnetic properties of KBS and KM for real water treatment.

Pyrolyzed magnetic NiO/carbon-derived nanocomposite from a hierarchical nickel-based metal-organic framework with ultrahigh adsorption capacity

Herein, a simple one-pot solvothermal approach is used to create magnetic porous carbon nanocomposites which obtained from a nickel-based metal-organic framework (Ni-MOF) and examined for their ability to uptake methyl orange (MO) dye. Derived carbons with exceptional porosity and magnetic properties were created during the different pyrolysis temperatures of Ni-MOF (700, 800, and 900 °C) under a nitrogen atmosphere. The black powders were given the names CDM-700, CDM-800, and CDM-900 after they were obtained. A variety of analysis methods, including FESEM, EDS, XRD, FTIR, VSM, and N₂ adsorption-desorption were used to characterize as-prepared powders. Furthermore, adsorbent dosage, contact time, pH variation, and initial dye concentration effects was investigated. The maximum adsorption capacities were 307.38, 5976.35, 4992.39, and 2636.54 mg/g for Ni-MOF, CDM-700, CDM-800, and CDM-900, respectively, which show the ultrahigh capacity of the resulted nanocomposites compared to newest materials. The results showed that not only the crystallinity turned but also the specific surface area was increased about four times after paralyzing. The results showed that the maximum adsorption capacity of MO dye for CDM-700 was obtained at adsorbent dosage of 0.083 g/L, contact time of 60 min, feed pH of 3, and temperature of 45 °C. The Langmuir model has the best match and suggests the adsorption process as a single layer. According to the results of reaction kinetic studies using well-known models, the pseudo-second-order model (R² = 0.9989) displayed high agreement with the experimental data. The synthesized nanocomposite is introduced as a promising superadsorbent for eliminating dyes from contaminated water due to strong recycling performance up to the fifth cycle.

Experimental evaluation of cobalt adsorption capacity of walnut shell by organic acid activation

Cobalt, from industrial waste and nuclear laundry, possess health risk to human beings, animals and plants. Number of methods, other than adsorption, have been reported in literature for Co removal from waste water. In this research walnut shell powder after modification has been utilized for Co adsorption. First step of modification involved chemical treatment by four different organic acids for 72 h. Samples were collected at 24, 48 and 72 h. Second step involved thermal treatment of 72 h samples. Unmodified and modified particles have been analyzed by chemical methods and instruments i.e. UV spectrometer, FTIR, cyclic voltammetry (CV) and microscopic imaging. Thermally treated samples have shown augmented Co adsorption. CV analysis showed thermally treated samples with better capacitance. Particles modified by oxalic acid presented better Co adsorption. Oxalic acid treated particles activated for 72 h with thermal treatment provided maximum adsorption capacity 1327 ± 20.6 mg/g against Co(II) at pH 7, stirring 200 rpm, initial concentration 20 ml, adsorbent dosage (5 mg) and contact time 240 min at room temperature.

Magnetic Biochar Obtained by Chemical Coprecipitation and Pyrolysis of Corn Cob Residues: Characterization and Methylene Blue Adsorption

Biochar is a carbonaceous and porous material with limited adsorption capacity, which increases by modifying its surface. Many of the biochars modified with magnetic nanoparticles reported previously were obtained in two steps: first, the biomass was pyrolyzed, and then the modification was performed. In this research, a biochar with Fe₃O₄ particles was obtained during the pyrolysis process. Corn cob residues were used to obtain the biochar (i.e., BCM) and the magnetic one (i.e., BCM_Fe). The BCM_Fe biochar was synthesized by a chemical coprecipitation technique prior to the pyrolysis process. The biochars obtained were characterized to determine their physicochemical, surface, and structural properties. The characterization revealed a porous surface with a 1013.52 m²/g area for BCM and 903.67 m²/g for BCM_Fe. The pores were uniformly distributed, as observed in SEM images. BCM_Fe showed Fe₃O₄ particles on the surface with a spherical shape and a uniform distribution. According to FTIR analysis, the functional groups formed on the surface were aliphatic and carbonyl functional groups. Ash content in the biochar was 4.0% in BCM and 8.0% in BCM_Fe; the difference corresponded to the presence of inorganic elements. The TGA showed that BCM lost 93.8 wt% while BCM_Fe was more thermally stable due to the inorganic species on the biochar surface, with a weight loss of 78.6%. Both biochars were tested as adsorbent materials for methylene blue. BCM and BCM_Fe obtained a maximum adsorption capacity (q_m) of 23.17 mg/g and 39.66 mg/g, respectively. The obtained biochars are promising materials for the efficient removal of organic pollutants.

Brilliant blue FCF dye adsorption using magnetic activated carbon from Sapelli wood sawdust

Sapelli wood sawdust-derived magnetic activated carbon (SWSMAC) was produced by single-step pyrolysis using KOH and NiCl₂ as activating and magnetization agents. SWSMAC was characterized by several techniques (SEM/EDS, N₂ adsorption/desorption isotherms, FTIR, XRD, VSM, and pH_PZC) and applied in the brilliant blue FCF dye adsorption from an aqueous medium. The obtained SWSMAC was a mesoporous material and showed good textural properties. Metallic nanostructured Ni particles were observed. Also, SWSMAC exhibited ferromagnetic properties. In the adsorption experiments, adequate conditions were an adsorbent dosage of 0.75 g L^-1 and a solution pH of 4. The adsorption was fast, and the pseudo-second-order demonstrated greater suitability to the kinetic data. The Sips model fitted the equilibrium data well, and the maximum adsorption capacity predicted by this model was 105.88 mg g^-1 (at 55 °C). The thermodynamic study revealed that the adsorption was spontaneous, favorable, and endothermic. Besides, the mechanistic elucidation suggested that electrostatic interactions, hydrogen bonding, π-π interactions, and n-π interactions were involved in the brilliant blue FCF dye adsorption onto SWSMAC. In summary, an advanced adsorbent material was developed from waste by single-step pyrolysis, and this material effectively adsorbs brilliant blue FCF dye.

Adsorption of anionic and cationic dyes in aqueous solution by a sustainable and low-cost activated carbon based on argan solid waste treated with H3PO4

The objective of this work is to study the adsorption capacity of a natural and low-cost material prepared from argan waste treated with H₃PO₄ towards two dyes of different molecular charges and presenting an acute toxicity, the methyl orange (MO, anionic dye) and the methylene blue (MB, cationic dye). The prepared adsorbent was characterized by SEM, EDX, FTIR, and BET specific surface. These analyses showed the presence of C (42%), O (55%), and P (3%) and a remarkable difference between the morphology of the precursor and that of the obtained material with a specific surface of 475 m²/g and a very porous structure as well as the main functional groups, O-H, C=O, and C-H. The influence of the pH showed a maximum adsorption at pH =2 for MO and at pH = 10 for MB. Investigation of the effect of time on the adsorption of anionic and cationic dyes revealed that the contact time at equilibrium was 240 and 180 min, respectively. The isotherms that best fit the adsorption of MO and MB are the Langmuir model and the Freundlich model respectively. The kinetic study showed that the experimental data are in agreement with the pseudo-second-order model. Regeneration of the saturated material was also studied for the probability of reusing the adsorbent in many experiments. The valorization of argan waste into activated carbon using H₃PO₄ has allowed to obtain an effective adsorbent for the removal of anionic and cationic dyes and create an added value for environmental sustainability.

Drying enables multiple reuses of activated carbon without regeneration

Traditional regeneration of activated carbon is usually carried out by high-temperature oxidation in industrial processes, which reduces the quality and performance of the adsorbent, thereby increasing costs and damaging the environment. In this study, a simple drying process is proposed to enable reuse of spent activated carbon. The feasibility and merits of this method were evaluated in batch and continuous adsorption modes using dyes as adsorbates. The batch adsorption results showed that the activated carbon could be reused seven times after a simple drying process, because it led to full occupancy of the activated carbon pores by adsorbate molecules. The cumulative adsorption capacities of the activated carbon were as high as 1005.3 mg/g for methyl orange (MO) and 954.8 mg/g for methylene blue (MB). Continuous adsorption experiments in a fixed-bed column demonstrated that the activated carbon column could be reused more than three times after simply drying. Moreover, dye molecules adsorbed by the activated carbon were not leached by the stream of dye solution during reuse. This drying method exhibits three main merits for reuse of activated carbon, including (1) remarkably reduced consumption of fresh activated carbon to 51.5% or below, (2) significantly increased recovery of high-value adsorbate from the liquid phase, and (3) potential integration of multiple steps for industrial adsorption processes.

Removal of Methylene Blue from Water Using Magnetic GTL-Derived Biosolids: Study of Adsorption Isotherms and Kinetic Models

Global waste production is significantly rising with the increase in population. Efforts are being made to utilize waste in meaningful ways and increase its economic value. This research makes one such effort by utilizing gas-to-liquid (GTL)-derived biosolids, a significant waste produced from the wastewater treatment process. To understand the surface properties, the biosolid waste (BS) that is activated directly using potassium carbonate, labelled as KBS, has been characterized using scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), and Brunauer-Emmett-Teller (BET). The characterization shows that the surface area of BS increased from 0.010 to 156 m²/g upon activation. The EDS and XPS results show an increase in the metal content after activation (especially iron); additionally, XRD revealed the presence of magnetite and potassium iron oxide upon activation. Furthermore, the magnetic field was recorded to be 0.1 mT using a tesla meter. The magnetic properties present in the activated carbon show potential for pollutant removal. Adsorption studies of methylene blue using KBS show a maximum adsorption capacity of 59.27 mg/g; the adsorption process is rapid and reaches equilibrium after 9 h. Modelling using seven different isotherm and kinetic models reveals the best fit for the Langmuir-Freundlich and Diffusion-chemisorptionmodels, respectively. Additional thermodynamic calculations conclude the adsorption system to be exothermic, spontaneous, and favoring physisorption.

Black-wattle tannin/kraft lignin H3PO4-activated carbon xerogels as excellent and sustainable adsorbents

This work proposed new black-wattle tannin/kraft lignin H₃PO₄-activated carbon xerogels as sustainable and efficient adsorbents. The precursors were chosen based on their eco-friendly and cost-effective nature, aiming to achieve adsorbents with high adsorption capacities. Carbon xerogels were synthesized through polycondensation with formaldehyde and alkaline catalyst in a simple one-pot procedure. Activation was performed using H₃PO₄ in a tubular furnace (500 °C), under a nitrogen atmosphere. Results show that the inclusion of the kraft lignin led to changes in the morphology of the materials, facilitating the development of their porous structure and increasing specific surface area and pore volume. The best adsorbent (XLT 50 %) was synthesized using a 1:1 tannin/kraft lignin mass ratio. This material presented an adsorption capacity of nearly 1150 mg g^-1 of methylene blue (pH = 5 and T = 298 K), which was linked to its high specific surface area of 1348 m² g^-1. The adsorption process followed the pseudo-second-order kinetic model, whereas the adsorption isotherms were best fitted by the Sips model. The XLT 50 % presented good reusability properties, maintaining its adsorption capacity for 3 cycles. Finally, the XLT 50 % presented good adsorptive properties toward other pollutants (methyl orange, 4-chlorophenol, and hexavalent chromium), indicating its versatility for adsorption processes.

Modified Orange Peel Waste as a Sustainable Material for Adsorption of Contaminants

World orange production is estimated at 60 million tons per annum, while the annual production of orange peel waste is 32 million tons. According to available data, the adsorption capacity of orange peel ranges from 3 mg/g to 5 mg/g, while their water uptake is lower than 1 mg/g. The low water uptake of orange peel and the abundance of biomass in nature has made orange peel an excellent biosorption material. This review summarised different studies on orange peel adsorption of various contaminants to identify properties of orange peel that influence the adsorption of contaminants. Most of the literature reviewed studied orange peel adsorption of heavy metals, followed by studies on the adsorption of dyes, while few studies have investigated adsorption of oil by orange peel. FTIR spectra analysis and SEM micrographs of raw and activated orange peels were studied to understand the structural properties of the biomass responsible for adsorption. The study identified pectin, hydroxyl, carbonyl, carboxyl, and amine groups as components and important functional groups responsible for adsorption in orange peel. Furthermore, changes were observed in the structural properties of the peel after undergoing various modifications. Physical modification increased the surface area for binding and the adsorption of contaminants, while chemical treatments increased the carboxylic groups enhancing adsorption and the binding of contaminants. In addition, heating orange peel during the thermal modification process resulted in a highly porous structure and a subsequent increase in adsorption capacities. In conclusion, physical, chemical, and thermal treatments improve the structural properties of orange peel, resulting in high biosorption uptake. However, orange peels treated with chemicals recorded the highest contaminants adsorption capacities.

Application of Walnut Shell Biowaste as an Inexpensive Adsorbent for Methylene Blue Dye: Isotherms, Kinetics, Thermodynamics, and Modeling

This research aimed to assess the adsorption properties of raw walnut shell powder (WNSp) for the elimination of methylene blue (MB) from an aqueous medium. The initial MB concentration (2–50 mg/L), the mass of the biomaterial (0.1–1 g/L), the contact time (10–120 min), the medium’s pH (2–12), and the temperature (25–55 °C) were optimized as experimental conditions. A maximum adsorption capacity of 19.99 mg/g was obtained at an MB concentration of 50 mg/L, a medium pH of 6.93 and a temperature of 25 °C, using 0.2 g/L of WNSp. These conditions showed that the MB dye elimination process occurred spontaneously. Different analytical approaches were used to characterize the WNSp biomaterial, including functional groups involved in MB adsorption, the surface characteristics and morphological features of the WNSp before and after MB uptake, and identification of WNSp based on their diffraction pattern. The experimental isotherm data were analyzed by the Langmuir and Freundlich models for the adsorption of MB dye. The corresponding values of parameter RL of Langmuir were between 0.51 and 0.172, which confirmed the WNSp’s favorable MB dye adsorption. The experimental kinetic data were examined, and the pseudo-second-order model was shown to be more suitable for describing the adsorption process, with an excellent determination coefficient (R2 = 0.999). The exchanged standard enthalpy (H° = −22.456 KJ.mol−1) was calculated using the van ‘t Hoff equation, and it was proven that the adsorption process was exothermic. The spontaneous nature and feasibility of the MB dye adsorption process on WNSp were validated by negative standard enthalpy values (G°) ranging from −2.580 to −0.469 at different temperatures. It was established that WNSp may be employed as a novel, effective, low-cost adsorbent for the elimination of methylene blue in aqueous solutions.

Controlled design of Na-P1 zeolite/ porous carbon composites from coal gasification fine slag for high-performance adsorbent

Low-cost and concentrated industrial wastes have been recognized as a sustainable resource for preparation of new functional materials. Here, a new method was designed for the synthesis of porous composites containing high-purity Na-P1 zeolite and porous carbon from waste coal gasification fine slag (CGFS), which was treated first by acid leaching to controllably remove metal impurities and adjust Si/Al ratio, followed by NaOH fusion and hydrothermal treatment. By leaching with 1.0 mol/L HCl solution, the Si/Al ratio of the raw CGFS increased to 5.7, and the obtained CZ-1.0 consisted of high-purity Na-P1 zeolite with a typical cone-shaped flower cluster shape. The residue carbon in CGFS can be further activated to form porous carbon and graphite carbon layers interposed in the zeolite structure. The specific surface area and pore volume of CZ-1.0 reached 153.91 m²/g and 0.18 cm³/g, respectively. CZ-1.0 exhibited remarkable adsorption performance for methylene blue (MB) with the adsorption capacity reaching 137.5 mg/g for 100 mg/L MB solution. The adsorption process is mainly controlled by the chemisorption mechanism, and the adsorption of MB by CZ-1.0 may include ion exchange, hydrogen bond interaction, π-π bond interaction and van der Waals force. NaCl solution was successfully used as the desorption agent to regenerate the composite material, and the removal rate remained above 92% after five cycles. This work provides an effective strategy to synthesize a practically applicable adsorbent from the waste coal gasification fine slag for the purification of MB wastewater.

Synthesis of high-quality NaP1 zeolite from municipal solid waste incineration fly ash by microwave-assisted hydrothermal method and its adsorption capacity

The Si and Al in municipal solid waste incineration fly ash (MSWI FA) can be utilized for zeolite fabrication, which can improve the application value of the products. This study focuses on the fabrication of zeolite from MSWI FA by microwave-assisted hydrothermal (MH) treatment. The effects of magnetic stirring time, Na₂SiO₃ dosage, MH time, and NaOH solution concentration on the crystallization of zeolite NaP1 from MSWI FA are systematically analyzed. The synthetic products are analyzed through spectroscopic and mineralogical methods. The results show that zeolite NaP1 with high crystallinity (51.68 %) can be fabricated by magnetic stirring and MH treatment, and the cation exchange capacity (CEC) of the product can reach a value of 2.58 meq/g, which is approximately 133 times that of the CEC of MSWI FA. The Si/Al ratio plays a decisive role in the zeolite NaP1 synthesis, and a Na₂SiO₃ dosage of 30 wt% is adopted for zeolite NaP1 fabrication. A NaOH concentration of 1 M is sufficient for zeolite NaP1 synthesis. Additionally, the zeolite NaP1 content is found to obviously increase with increasing MH time from 0.5 h to 2 h. To demonstrate the feasibility of the method provided in this study, the optimal experimental condition is employed for various MSWI FAs, and zeolite NaP1 and analcime are fabricated successfully. The leachability of heavy metals for the synthetic products was evaluated, which met the requirements for pollution control. The BET surface area and total pore volume of zeolite NaP1 fabricated at optimal condition are 61.42 m²/g and 0.44 cm³/g, respectively. The adsorption capacity of zeolite NaP1 for Cu²⁺ ion and methylene blue are determined to be 84.65 mg/g and 84.55 mg/g, respectively, indicating zeolite NaP1 is a potential adsorbent for cation ion and dyes. This study provides an environmentally friendly scheme for the utilization of MSWI FA.

A Novel P@SiO2 Nano-Composite as Effective Adsorbent to Remove Methylene Blue Dye from Aqueous Media

This work aims to prepare a novel phosphate-embedded silica nanoparticles (P@SiO₂) nanocomposite as an effective adsorbent through a hydrothermal route. Firstly, a mixed solution of sodium silicate and sodium phosphate was passed through a strong acidic resin to convert it into hydrogen form. After that, the resultant solution was hydrothermally treated to yield P@SiO₂ nanocomposite. Using kinetic studies, methylene blue (MB) dye was selected to study the removal behavior of the P@SiO₂ nanocomposite. The obtained composite was characterized using several advanced techniques. The experimental results showed rapid kinetic adsorption where the equilibrium was reached within 100 s, and the pseudo-second-order fitted well with experimental data. Moreover, according to Langmuir, one gram of P@SiO₂ nanocomposite can remove 76.92 mg of the methylene blue dye. The thermodynamic studies showed that the adsorption process was spontaneous, exothermic, and ordered at the solid/solution interface. Finally, the results indicated that the presence of NaCl did not impact the adsorption behavior of MB dye. Due to the significant efficiency and promising properties of the prepared P@SiO₂ nanocomposite, it could be used as an effective adsorbent material to remove various cationic forms of pollutants from aqueous solutions in future works.

Chitin-Based Magnesium Oxide Biocomposite for the Removal of Methyl Orange from Water

In this work, a cost-effective chitin-based magnesium oxide (CHt@MgO) biocomposite with excellent anionic methyl orange (MO) dye removal efficiency from water was developed. The CHt@MgO biocomposite was characterized by FT-IR, XRD, SEM-EDX, and TGA/DTG. Results proved the successful synthesis of CHt@MgO biocomposite. Adsorption of MO on the CHt@MgO biocomposite was optimized by varying experimental conditions such as pH, amount of adsorbent (m), contact time (t), temperature (T), and initial MO concentration (C_o). The optimized parameters for MO removal by CHt@MgO biocomposite were as follows: pH, 6; m, 2 g/L; t, 120 min. Two common isotherm models (Langmuir and Freundlich) and three kinetic models (pseudo-first-order (PFO), pseudo-second-order (PSO), and intraparticle diffusion (IPD)) were tested for experimental data fitting. Results showed that Langmuir and PFO were the most suitable to respectively describe equilibrium and kinetic results on the adsorption of MO adsorption on CHt@MgO biocomposite. The maximum Langmuir monolayer adsorption capacity (q_m) on CHt@MgO biocomposite toward MO dye was 252 mg/g at 60 °C. The reusability tests revealed that CHt@MgO biocomposite possessed high (90.7%) removal efficiency after the fifth regeneration cycle.

Recyclable magnetic Fe3O4@C for methylene blue removal under microwave-induced reaction system

The reclamation and removal of organic pollutants are difficult issues of world concern. In this study, a microwave-induced reaction system (MIRS) is applied to synthesize the multifunctional composite of Fe₃O₄@C, which is employed to adsorb, separate and catalytic oxide the typical organic dye of methylene blue (MB). SEM, TEM, VSM, XPS, pHpzc, and N₂ adsorption performances are carried out to characterize the Fe₃O₄@C. Results show that the Fe₃O₄@C mainly consists of activated Fe-O-C microspheres, which possess plentiful mesopore and macropore structures on surfaces. Batch adsorption experiments were carried out by varying key reaction conditions to optimize these. The maximum adsorption capacity of MB onto the Fe₃O₄@C was 305.0 mg g^-1 in 120 min, at pH 10, and at a temperature of 323 K. MIRS was also assisted to regenerate the spent Fe₃O₄@C which presented good regeneration efficiency by sustaining 16 regeneration cycles without any oxidizing agent. SEM images and FTIR spectrum verified that MB would translate into greater or smaller-sized carbon microspheres. What's more, the adsorption of MB onto both initial and the 16th regenerated Fe₃O₄@C obeyed the Langmuir isotherm model and followed the pseudo-second-order adsorption kinetics, indicating the adsorptive stability after regeneration. In this study, the Fe₃O₄@C combined with MIRS may be one innovative strategy for organic pollutants' complete removal in the future.

Reed Rhizome Residue-Based Activated Carbon Adsorption Ultrafiltration Membranes for Enhanced MB Removal

Novel adsorption ultrafiltration (ADUF) membrane was designed for the removal of methylene blue (MB) by introducing Chinese herbal waste-based activated carbon (AC) into the ultrafiltration membrane. We prepared AC particles from Chinese herbal medicine waste residue (reed rhizome residue) as a raw material by ZnCl₂ activation and introduced them into the ultrafiltration membrane by phase inversion to prepare a reed rhizome residue-based activated carbon adsorption ultrafiltration (RAC-ADUF) membrane. The RAC-ADUF-0.1 membrane was characterized by a series of physical structures and chemical properties, which showed that the prepared membrane has a more hydrophilic surface and high porosity. The RAC-ADUF-0.1 membrane showed an excellent pure water flux of 255.77 L·m^-2·h^-1 and a high bovine serum albumin rejection of 99.3%. The RAC-ADUF membranes also possessed excellent antifouling performance. Notably, the RAC-ADUF-0.1 membrane provides excellent removal of MB (99% retention) compared to conventional ultrafiltration membranes. The static adsorption capacity was up to 238.48 mg/g. The significant increase in dynamic adsorption capacity on the RAC-ADUF membrane is due to the three-dimensional distribution of RAC particles on the PSF membrane cross section, which provides more active sites and increases the contact time between RAC and MB. By fitting the adsorption kinetics and isothermal adsorption curves, the results showed that the pseudo-second-order kinetic model and the Langmuir isothermal model were more accurate in explaining the adsorption process. Further kinetic analysis showed that the adsorption process of MB molecules on RAC-ADUF membranes is controlled by both external mass transfer and intraparticle diffusion, with intraparticle diffusion playing a dominant role. In addition, the RAC-ADUF membrane exhibited outstanding adsorption and regeneration abilities, and the MB removal rate stayed at about 95% after 8 adsorption regeneration experiments. In conclusion, this study provides a new idea for the preparation strategy of an adsorption ultrafiltration membrane with high rejection and high permeability and the reuse of Chinese herbal medicine waste residue.

ZnO Particles Modified MgAl Coatings with Improved Photocatalytic Activity Formed by Plasma Electrolytic Oxidation of AZ31 Magnesium Alloy in Aluminate Electrolyte

MgAl and MgAl/ZnO coatings were prepared by plasma electrolytic oxidation (PEO) of AZ31 magnesium alloy in aluminate electrolyte (5 g/L NaAlO2) without and with addition of ZnO particles in various concentrations. The MgAl coating was partially crystallized and contained MgO and MgAl2O4 phases. The addition of ZnO particles to aluminate electrolyte had no significant effect on the surface morphology of formed coatings, while the Zn content increased with ZnO particle concentrations. X-ray diffraction confirmed the incorporation of ZnO particles in the coatings. The photodegradation of methyl orange (10 cm3 of 8 mg/L) was used to measure the photocatalytic activity (PA) of MgAl and MgAl/ZnO coatings. The PA of MgAl coating after 8 h of irradiation was around 58%, while the PA of MgAl/ZnO coatings formed in aluminate electrolyte with the addition of ZnO particles in concentrations of 4 g/L, 8 g/L, and 12 g/L were around 69%, 86%, and 97%, respectively.