Thermal, antioxidant and swelling behaviour of transparent polyvinyl (alcohol) films in presence of hydrophobic citric acid-modified lignin nanoparticles

A demethylated lignin improved PVA-based supramolecular plastic with tough, degradable, and water-resistant performances

Poly (vinyl alcohol) (PVA), as an excellent degradable plastic feedstock, is limited by its diminishing stability in wet environment, low strength, thermal instability and nonopaque properties. In response to these concerns, a PVA/demethylated lignin-based supramolecular plastic (DPVA-HA-Fe-5) was designed and produced from PVA, demethylated lignin (DL), humic acid (HA) and Fe3+ ions via a simple casting method. As compared with pure PVA plastic, the tensile strength of DPVA-HA-Fe-5 were increased by 411 % to 410.61 MPa, and the breaking strain was increased by 149 % to 239.47 %. Notably, the hydrophobicity of DPVA-HA-Fe-5 was also significantly improved. Although in highly humid environment (stored in RH = 100 % for 10 days) or in alkaline organic solvent (stored in pyridine for 3 h), DPVA-HA-Fe-5 also showed excellent mechanical strengths of 302.9 and 222.99 MPa, respectively, which are equivalent or even superior to the most of commercial petroleum-based plastics. Moreover, the prepared plastics showed an outstanding UV resistance and shading performance, and about 98.3 % protection against ultraviolet radiation B rays and 90.7 % protection against visible light were obtained. In short, the introduction of lignin to improve the performance of PVA-based plastic is a feasible method, and it could facilitate the development of high-value utilization of lignin.

Enhanced antifungal properties of poly(butylene succinate) film with lignin nanoparticles and trans-cinnamaldehyde for mango packaging

Sustainable poly(butylene succinate) (PBS) films incorporating lignin nanoparticles (LN) and trans-cinnamaldehyde (CN) have been developed to preserve mango freshness and provide food safety. PBS/LN, PBS/CN, and PBS/LN/CN composite films were produced by blown film melt extrusion. This study investigated the effect of CN-LN on the CN remaining content, thermal, mechanical, and barrier properties, diffusion coefficient, and antifungal activity of PBS films both in vitro and in vivo. Results showed that LN in the PBS/LN/CN composite film contained more CN than in the PBS/CN film. The compatibility of CN-LN with PBS produced homogeneous surfaces with enhanced barrier properties. PBS/LN/CN composite films demonstrated superior antifungal efficacy, inhibiting the growth of Colletotrichum gloeosporioides and preserving mango quality during storage. Results suggested that incorporating LN into PBS composite films prolonged the sustained release of antifungal agents, thereby inhibiting microbial growth and extending the shelf life of mangoes. Development of PBS/LN/CN composite films is a beneficial step toward reducing food waste and enhancing food safety.

Preparation and Application of Degradable Lignin/Poly (Vinyl Alcohol) Polymers as Urea Slow-Release Coating Materials

The massive amount of water-soluble urea used leads to nutrient loss and environmental pollution in both water and soil. The aim of this study was to develop a novel lignin-based slow-release envelope material that has essential nitrogen and sulfur elements for plants. After the amination reaction with a hydrolysate of yak hair keratin, the coating formulation was obtained by adding different loadings (2, 5, 8, 14 wt%) of aminated lignin (AL) to 5% polyvinyl alcohol (PVA) solution. These formulations were cast into films and characterized for their structure, thermal stability, and mechanical and physicochemical properties. The results showed that the PVA-AL (8%) formulation had good physical and chemical properties in terms of water absorption and mechanical properties, and it showed good degradation in soil with 51% weight loss after 45 days. It is suitable for use as a coating material for fertilizers. Through high-pressure spraying technology, enveloped urea particles with a PVA-AL (8%) solution were obtained, which showed good morphology and slow-release performance. Compared with urea, the highest urea release was only 96.4% after 30 days, conforming to Higuchi model, Ritger-Peppas model, and second-order dynamic model. The continuous nitrogen supply of PVA-AL coated urea to Brassica napus was verified by potting experiments. Therefore, the lignin-based composite can be used as a coating material to produce a new slow-release nitrogen fertilizer for sustainable crop production.

Electrospinning of poly(ethylene oxide)/glass hybrid nanofibres for anticounterfeiting encoding

The use of photochromism to increase the credibility of consumer goods has shown great promise. To provide mechanically dependable anticounterfeiting nanofibres, it has also been critical to improve the engineering processes of authentication patterns. Mechanically robust and photoluminescent electrospun poly(ethylene oxide)/glass (PGLS) nanofibres (150-350 nm) immobilized with nanoparticles of lanthanide-doped aluminate (NLA; 8-15 nm) were developed using electrospinning technology for anticounterfeiting purposes. The provided nanofibrous membranes changed colour from transparent to green when irradiated with ultraviolet light. By delivering NLA with homogeneous distribution without aggregations, we were able to keep the nanofibrous membrane transparent. When excited at 365 nm, NLA@PGLS nanofibres showed an emission intensity at 517 nm. The hydrophobicity of NLA@PGLS nanofibres improved by raising the pigment concentration as the contact angle was increased from 146.4° to 160.3°. After being triggered by ultraviolet light, NLA@PGLS showed quick and reversible photochromism without fatigue. It was shown that the suggested method can be applied to reliably produce various anticounterfeiting materials.

Multi-functional polyvinyl alcohol/tannin acid composite films incorporated with lignin nanoparticles loaded by potassium sorbate

The biocompatible, biodegradable and strong polyvinyl alcohol-based films have been widely investigated and used in the field of active packaging. To endow with diverse function, this paper firstly prepared lignin nanoparticles loaded with potassium sorbate (LNP@PS) as additives to exploit additional antibacterial, UV blocking, oxygen barrier, and water barrier properties. Besides, tannin acid (TA) was incorporated for compensating and further enhancing mechanical properties. Results showed that the PVA-based composite films containing 3 % LNP@PS and 5 % TA could achieve the optimal tensile strength at 74.51 MPa, water vapor permeability at 7.015·10-13·g·cm/cm2·s·Pa and oxygen permeability at 1.93 cm3/m2·24 h MPa, which was an 165 % of increase, 47 % and 112 % of reduction respectively compared to pure PVA films. Additionally, the composite films exhibited apparently superior bacteria and oxygen resistance properties evidenced by microbial infection and free radical scavenging performance. In addition, the slow-release effect of PS assisted the strawberry preservation with an extension of 3 days, which provided a promising novel route to prepare active food packaging material.

Biodegradable, Strong, and Hydrophobic Regenerated Cellulose Films Enriched with Esterified Lignin Nanoparticles

The scientific community is pursuing significant efforts worldwide to develop environmentally viable film materials from biomass, particularly transparent, high-performance regenerated cellulose (RC) films, to replace traditional plastics. However, the inferior mechanical performance and hydrophilic nature of RC films are generally not suitable for use as a substitute for plastics in practical applications. Herein, lignin homogenization is used to synthesize high-performance composite films. The esterified lignin nanoparticles (ELNPs) with dispersible and binding advantages are prepared through esterification and nanometrization. In the presence of ELNPs, RC films exhibit a higher tensile strength (110.4 MPa), hydrophobic nature (103.6° water contact angle, 36.6% water absorption at 120 min, and 1.127 × 10-12 g cm cm-2 s-1 Pa-1 water vapor permeability), and exciting optical properties (high visible and low ultraviolet transmittance). The films further display antioxidant activity, oxygen barrier ability, and thermostability. The films completely biodegrade at 12 and 30% soil moisture. Overall, this study offers new insights into lignin valorization and regenerated cellulose composite films as novel bioplastic materials.

Nanotechnology in wood science: Innovations and applications

Application of nanomaterials is gaining tremendous interest in the field of wood science and technology for value addition and enhancing performance of wood and wood-based composites. This review focuses on the use of nanomaterials in improving the properties of wood and wood-based materials and protecting them from weathering, biodegradation, and other deteriorating agents. UV-resistant, self-cleaning (superhydrophobic) surfaces with anti-microbial properties have been developed using the extraordinary features of nanomaterials. Scratch-resistant nano-coatings also improve durability and aesthetic appeal of wood. Moreover, nanomaterials have been used as wood preservatives for increasing the resistance against wood deteriorating agents such as fungi, termites and borers. Wood can be made more resistant to ignition and slower to burn by introducing nano-clays or nanoparticles of metal-oxides. The use of nanocellulose and lignin nanoparticles in wood-based products has attracted huge interest in developing novel materials with improved properties. Nanocellulose and lignin nanoparticles derived/synthesized from woody biomass can enhance the mechanical properties such as strength and stiffness and impart additional functionalities to wood-based products. Cellulose nano-fibres/crystals find application in wide areas of materials science like reinforcement for composites. Incorporation of nanomaterials in resin has been used to enhance specific properties of wood-based composites. This review paper highlights some of the advancements in the use of nanotechnology in wood science, and its potential impact on the industry.

Sustainable lignin nanoparticles from coconut fiber waste for enhancing multifunctional properties of macroalgae biofilms

Multifunctional and sustainable packaging biofilms felicitous to changeable conditions are in large demand as substitutes to petroleum-derived synthetic films. Macroalgae with noticeable film-formation, abundant, low-cost, and edible properties is a promising bioresource for sustainable and eco-friendly packaging materials. However, the poor hydrophobicity and mechanical properties of sustainable macroalgae biofilms seriously impede their practical applications. Herein, lignin nanoparticles (LNPs) produced by a sustainable approach from black liquor of coconut fiber waste were incorporated in the macroalgae matrix to improve the water tolerance and mechanical characteristics of the biofilms. The effect of different LNPs loadings on the performance of biofilms, such as physical, morphological, surface roughness, structural, water resistance, mechanical, and thermal behaviors, were systematically evaluated and found to be considerably improved. Biofilm with 6 % LNPs presented the optimum enhancement in most ultimate performances. The optimized biofilm exhibited great hydrophobic features with a water contact angle of over 100° and high enhancement in the tensile strength of >60 %. This study proposes a facile and sustainable approach for designing and developing LNPs-macroalgae biofilms with excellent and multifunctional properties for sustainable high-performance packaging materials.

Sustainable organosolv-lignin coated nanosilver-halloysites reinforced poly (vinyl alcohol) nanocomposites for wound healing application

This study involves the fabrication of innovative poly (vinyl alcohol) nanocomposite films by incorporating silver-embedded clay nanotubes with organosolv-lignin by the solution casting approach. The confirmation of this procedure was achieved through the utilisation of many techniques, including FTIR, PXRD, FE-SEM, and TGA. The aforementioned research have verified the adherence of silver nanoparticles to the surface of raw halloysites. The confirmation of lignin functionalization on these nanotubes has been established. This novel nanofiller was used to make a range of nanocomposite films with varying weight percentages ranging from 0 wt% to 5 wt%. With the increase in the wt% of nanofillers, These nanocomposite films exhibited greater thermal and mechanical stability compared to plain PVA. An investigation was conducted to examine the impact of the films on the cellular behaviour of murine fibroblast (NIH3T3) cell lines. Based on the findings from cell proliferation and scratch testing, it has been determined that these nanocomposite films are not harmful to cells, exhibit a greater rate of cell multiplication (116 ± 1.19), and demonstrate increased migratory capabilities (86.5 ± 0.50). Further investigations of human blood corroborate the evidence that these films are compatible with blood. Nanocomposite films have the potential to serve as wound healers following pre-clinical and clinical testing.

Lignin beyond the status quo: recent and emerging composite applications

The demand for biodegradable materials across various industries has recently surged due to environmental concerns and the need for the adoption of renewable materials. In this context, lignin has emerged as a promising alternative, garnering significant attention as a biogenic resource that endows functional properties. This is primarily ascribed to its remarkable origin and structure that explains lignin's capacity to bind other molecules, reinforce composites, act as an antioxidant, and endow antimicrobial effects. This review summarizes recent advances in lignin-based composites, with particular emphasis on innovative methods for modifying lignin into micro and nanostructures and evaluating their functional contribution. Indeed, lignin-based composites can be tailored to have superior physicomechanical characteristics, biodegradability, and surface properties, thereby making them suitable for applications beyond the typical, for instance, in ecofriendly adhesives and advanced barrier technologies. Herein, we provide a comprehensive overview of the latest progress in the field of lignin utilization in emerging composite materials.

Regulation of the immune microenvironment by pioglitazone-loaded polylactic glycolic acid nanosphere composite scaffolds to promote vascularization and bone regeneration

Osteogenesis is caused by multiple factors, and the inflammatory response, osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs), regeneration of blood vessels, and other factors must be considered in bone tissue engineering. To effectively repair bone defect, it is important to decrease excessive inflammation, enhance the differentiation of mesenchymal stem cells into osteoblasts, and stimulate angiogenesis. Herein, nano-attapulgite (ATP), polyvinyl alcohol (PVA), and gelatin (GEL) scaffolds were produced using 3D printing technology and pioglitazone (PIO)-containing polylactic acid-glycolic acid (PLGA) nanospheres were added. In both in vitro and in vivo studies, material scaffolds with PIO-loaded polylactic acid-glycolic acid nanospheres could reduce the inflammatory response by encouraging macrophage polarization from M1 to M2 and promoting the osteogenic differentiation of BMSCs by activating the BMP2/Smad/RUNX2 signal pathway to repair bone defects. The vascularization of human umbilical vein endothelial cells (HUVECs) through the PI3K/AKT/HIF1-/VEGF pathway was also encouraged. In vivo research using PIO-containing PLGA nanospheres revealed massive collagen deposition in skin models. These findings indicate a potentially effective scaffold for bone healing, when PLGA nanospheres-which contain the drug PIO-are combined with ATP/PVA/GEL scaffolds.

Sonochemical synthesis of lignin nanoparticles and their applications in poly (vinyl) alcohol composites

Lignin is a common and abundant byproduct of the pulp and paper industry and is generally burned to produce steam. Opportunities exist to acquire greater value from lignin by leveraging the properties of this highly conjugated biomacromolecule for applications in UV absorption and polymer reinforcement. These applications can be commercialized by producing value-added lignin nanoparticles (LNPs) using a scalable sonochemical process. In the present research, monodisperse LNPs have been synthesized by subjecting aqueous dispersions of alkali lignin to acoustic irradiation. The resulting particle size distribution and colloidal stability, as determined by dynamic light scattering, transmission electron microscopy and zeta potential analysis, of LNPs can be adjusted by varying the solution pH and ultrasonication energy. As-synthesized LNPs with a mean diameter of 204 nm were incorporated into poly (vinyl) alcohol (PVA) to prepare thin and flexible nanocomposite films using a simple solvent casting method. The addition of 2.5 wt% LNP increased the material's Sun Protection Factor up to 26 compared to 0 for neat PVA, while maintaining light transmission above 75 % in the visible spectra. In addition, the tensile strength and elastic modulus of the PVA nanocomposites improved by 47 % and 36 %, respectively. The presence of LNP also enhanced the thermal stability of the materials. Significantly, the proposed sonochemical process may be generally applicable to the synthesis of a range of naturally-derived LNPs for a variety of value-added applications.

Experimental investigations on PVA/chitosan and PVA/chitin films for active food packaging using Oxytenanthera abyssinica lignin nanoparticles and its UV-shielding, antimicrobial, and antiradical effects

This study investigated the effect of adding lignin nanoparticles (LNPs) derived from Oxytenanthera abyssinica via alkali-acid nanoprecipitation method to polyvinyl alcohol/chitosan (PVA/CI) and polyvinyl alcohol/chitin (PVA/CH) films for the active food packaging applications. Adding LNPs at concentrations of 1 % and 3 % improved the films' thermal stability and mechanical properties. The lowest water solubility and moisture content were observed in PVA/CI/LNPs films. LNPs exhibited effective 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activities, with the highest values observed in PVA/CH/LNPS and PVA/CI/LNPS films with values of 87.47 and 88.74 % respectively. The addition of LNPs also improved the UV-blocking abilities of the films. PVA/CH/LNP3 and PVA/CI/LNP3 have the smallest percentage transmission values of 3.34 % and 0.86 % in the UV range. The overall migration of dietary stimulants was lower in PVA/CI/LNPS and PVA/CH/LNPS films compared to PVA film. Antibacterial tests demonstrated the inhibitory capacity of the synthesized biofilms against both gram-positive and negative bacterial species, with the highest inhibitory value of 26 mm. The study suggests that PVA/CH/LNPS and PVA/CI/LNPS films have potential applications as active food packaging materials and can be explored in other potential applications such as drug delivery, tissue engineering, wound healing, and slow-release urea fertilizer development.

Lignins as Promising Renewable Biopolymers and Bioactive Compounds for High-Performance Materials

The recycling of biomass into high-value-added materials requires important developments in research and technology to create a sustainable circular economy. Lignin, as a component of biomass, is a multipurpose aromatic polymer with a significant potential to be used as a renewable bioresource in many fields in which it acts both as promising biopolymer and bioactive compound. This comprehensive review gives brief insights into the recent research and technological trends on the potential of lignin development and utilization. It is divided into ten main sections, starting with an outlook on its diversity; main properties and possibilities to be used as a raw material for fuels, aromatic chemicals, plastics, or thermoset substitutes; and new developments in the use of lignin as a bioactive compound and in nanoparticles, hydrogels, 3D-printing-based lignin biomaterials, new sustainable biomaterials, and energy production and storage. In each section are presented recent developments in the preparation of lignin-based biomaterials, especially the green approaches to obtaining nanoparticles, hydrogels, and multifunctional materials as blends and bio(nano)composites; most suitable lignin type for each category of the envisaged products; main properties of the obtained lignin-based materials, etc. Different application categories of lignin within various sectors, which could provide completely sustainable energy conversion, such as in agriculture and environment protection, food packaging, biomedicine, and cosmetics, are also described. The medical and therapeutic potential of lignin-derived materials is evidenced in applications such as antimicrobial, antiviral, and antitumor agents; carriers for drug delivery systems with controlled/targeting drug release; tissue engineering and wound healing; and coatings, natural sunscreen, and surfactants. Lignin is mainly used for fuel, and, recently, studies highlighted more sustainable bioenergy production technologies, such as the supercapacitor electrode, photocatalysts, and photovoltaics.

A Novel UV Barrier Poly(lactic acid)/Poly(butylene succinate) Composite Biodegradable Film Enhanced by Cellulose Extracted from Coconut Shell

Cellulose was extracted from coconut shell powder (CSP) as a renewable biomass resource and utilized as a reinforcing material in poly(lactic acid)/poly(butylene succinate) (PLA/PBS) solvent casting films. The extraction process involved delignification and mercerization of CSP. Microscopic investigation of the extracted microfibers demonstrated a reduction in diameter and a rougher surface characteristic compared to the raw CSP. The cellulose prepared in this study exhibited improved thermal stability and higher crystallinity (54.3%) compared to CSP. The morphology of the cycrofractured surface, thermal analysis, mechanical property, and UV transmittance of films were measured and compared. Agglomeration of 3 wt.% of cellulose was observed in PLA/PBS films. The presence of cellulose higher than 1 wt.% in the PLA/PBS decreased the onset decomposition temperature and maximum decomposition temperature of films. However, the films loading 3 wt.% of cellulose had a higher char formation (5.47%) compared to neat PLA/PBS films. The presence of cellulose promoted the formation of non-uniform crystals, while cellulose had a slightly negative impact on crystallinity due to the disruption of polymer chains at lower cellulose content (0.3, 0.5 wt.%). The mechanical strength of PLA/PBS films decreased as the cellulose content increased. Moreover, PLA/PBS film with 3 wt.% of cellulose appeared to show a 3% and 7.5% decrease in transmittance in UVC (275 nm) and UVA (335 nm) regions compared to neat PLA/PBS films while maintaining a certain transparency.

Current roles of lignin for the agroindustry: Applications, challenges, and opportunities

Lignin has the potential to be used as an additive, coating agent, fertilizer, plant growth stimulator, and packaging material in the agroindustry due to its functional aromatic structure. The quantitative measurement of functional groups is a significant element of the research for lignin structure since they directly impact their optical, dispersion, and chemical properties. These physical and chemical properties of lignin strongly depend on its type and source and its isolation procedure. Thus, lignin provides numerous opportunities for the circular economy in the agroindustry; however, studying and resolving the challenges associated with its separation, purification, and modification is required. This review discusses the most recent findings on lignin use in agroindustry and historical facts about lignin. The properties of lignin and its roles as coating agents, pesticide carriers, plant growth stimulators, and soil-improving agents have been summarized. The emerging challenges in the field of lignin-based agroindustry are considered, and potential future steps to overcome these challenges are discussed.

Opportunities and Challenges for Lignin Valorization in Food Packaging, Antimicrobial, and Agricultural Applications

The exploration of renewable resources is essential to help transition toward a more sustainable materials economy. The valorization of lignin can be a key component of this transition. Lignin is an aromatic polymer that constitutes approximately one-third of the total lignocellulosic biomass and is isolated in huge quantities as a waste material of biofuel and paper production. About 98% of the 100 million tons of lignin produced each year is simply burned as low-value fuel, so this renewable polymer is widely available at very low cost. Lignin has valuable properties that make it a promising material for numerous applications, but it is far from being fully exploited. The aim of this Perspective is to highlight opportunities and challenges for the use of lignin-based materials in food packaging, antimicrobial, and agricultural applications. In the first part, the ongoing research and the possible future developments for the use of lignin as an additive to improve mechanical, gas and UV barrier, and antioxidant properties of food packaging items will be treated. Second, the application of lignin as an antimicrobial agent will be discussed to elaborate on the activity of lignin against bacteria, fungi, and viruses. Finally, the use of lignin in agriculture will be presented by focusing on the application of lignin as fertilizer.

Physicochemical properties of lignin nanoparticles from softwood and their potential application in sustainable pre-harvest bagging as transparent UV-shielding films

Technical lignin can be mainly obtained as a waste by-product from pulp industry, and it exhibits unique properties including ultraviolet adsorption, biodegradable, antibacterial, and antioxidant which can be utilized for bioplastic applications. However, common limitations of technical lignin for plastic applications are compatibility mainly due to poor interfacial adhesion, relatively large particle size and impurity. In this study lignin nanoparticles from softwood (S-LNPs) were successfully produced through a continuous-green-scalable antisolvent precipitation and the suitability of S-LNPs for fabrication of bio-composite polybutylene succinate (PBS) films using conventional blown film extrusion was examined. The attained S-LNPs showed lower ash content, higher phenolic content and higher lignin content compared to pristine softwood kraft lignin (S-lignin). Rheological property including shear viscosity and melt-flow index was determined. The obtained PBS/S-LNP composite films showed improved tensile modulus, higher water vapor transmission rate and excellent UV-shielding ability compared to neat PBS and PBS/S-lignin films. Accelerated weathering testing was conducted to replicate outdoor conditions. Degradation indices including carbonyl, vinyl and hydroxyl of the weathered PBS/lignin composites were evaluated for photo-oxidative stability. The S-LNPs as multifunctional bio-additives in biodegradable composite film exhibited superior performances of transparency, UV-absorption and stiffness with high photo-oxidative stability suitable for outdoor applications.

Lignin as a bioactive polymer and heavy metal absorber- an overview

As a pulping and bio-refinery by-product with phenolic chemical structure, lignin indicated high potential as natural antioxidant activity, UV blocker, antibacterial and toxic material absorbent properties. Presence of phenolic hydroxyl groups in lignin structure plays the main role of its antioxidant activity. However, lignin antioxidant power can change depending on its other structural features and functional groups like ortho-methoxy groups, -OCH₃ groups, the α-CH₂ groups, the aliphatic carbonyl groups, and the size of π-conjugated systems. Lignin in mixture with synthetic polymers, improved their thermal stability. Lignin has high UV light absorbing potential in broad-spectrum (UVA, UVB). Adding 1-5% of lignin into hand cream indicated excellent range of sun protection factor (SPF) with more than 95% UV light absorption. Lignin also indicated strong UV light protection when applied in different transparent film and protect paint, oil, and varnish from UV degradation. Lignosulfonate and other modified lignin including chemically modification, nano-particles and lignin hydrogel indicated high potential as heavy metal absorber.

Green and Efficient Preparation of Tailed Lignin Nanoparticles and UV Shielding Composite Films

Lignin nanoparticles (LNP) with various morphologies could be prepared with solvent-antisolvent methods. However, the employed toxic chemicals limited its large-scale application. In this study, an extremely green method using only ethanol and water as solvent and antisolvent was reported. Besides, with the syringaldehyde (SA) addition and its anchoring action on the lignin particles, a forming process of the tailed structure was observed and resulted. Moreover, the improved electronegativity originating from the phenolic hydroxyl groups enhanced the size distribution uniformity, and the new absorption peaks at 1190 cm^-1 demonstrated the involvement of SA in the LNP formation. Lastly, the tailed lignin nanoparticles (T-LNP) composited with, respectively, polyvinyl alcohol, chitosan, cellulose nanofibers, cationic etherified starch, and sodium alginate were successfully prepared. The outstanding UV-shielding and free radical scavenging properties in the above composites showed their great potential in wide applications in packaging materials.

A review on lignin antioxidants: Their sources, isolations, antioxidant activities and various applications

Lignin, a biopolymer obtained from agricultural/forestry residues or paper pulping wastewater, is rich in aromatic structure, which is central to its adoption as a candidate to natural antioxidants. Through insight into its structural features from biomass, different functional groups would influence lignin antioxidant activity, wherein phenolic content is the most important factor, hence massive studies have focused on its improvement via different pretreatments and post-processing methods. Besides, lignin nanoparticles and chemical modifications are also efficient methods to improve antioxidant activity via increasing free content and decreasing bond dissociation enthalpy of phenolic hydroxyl. Lignin samples exhibit comparable radicals scavenging ability to commercial ones, showing their potential as renewable alternatives of synthesized antioxidants. Besides, their applications have also been discussed, which demonstrates lignin potential as an inexpensive antioxidant additive and consequent improvements on multiple functionalities. This review is dedicated to summarize lignin antioxidants extracted from biomass resources, methods to improve their antioxidant activity and their applications, which is beneficial for realizing lignin valorization.

Fully Biobased Photothermal Films and Coatings for Indoor Ultraviolet Radiation and Heat Management

Sustainable materials are needed to mitigate against the increase in energy consumption resulting from population growth and urbanization. Here, we report fully biobased nanocomposite films and coatings that display efficient photothermal activity and selective absorption of ultraviolet (UV) radiation. The nanocomposites with 20 wt % of lignin nanoparticles (LNPs) embedded in a chitosan matrix displayed an efficient UV blocking of 97% at 400 nm along with solar energy-harvesting properties. The reflectance spectra of the nanocomposite films revealed the importance of well-dispersed nanoparticles in the matrix to achieve efficient UV-blocking properties. Finally, yet importantly, we demonstrate the nanocomposites with 20 wt % LNPs as photothermal glass coatings for passive cooling of indoor temperature by simply tailoring the coating thickness. Under simulated solar irradiation of 100 mW/cm², the 20 μm coating achieved a 58% decrease in the temperature increment in comparison to the system with uncoated glass. These renewable nanocomposite films and coatings are highly promising sustainable solutions to facilitate indoor thermal management and improve human health and well-being.

Development and evaluation of Moringa extract incorporated Chitosan/Guar gum/Poly (vinyl alcohol) active films for food packaging applications

The present study contributes the synthesis of active films with the incorporation of moringa extract (ME) into chitosan (CS)/guar gum (GG)/poly(vinyl alcohol) (PVA) matrix (CGPM) by simple solvent casting technique. The effect of ME on the mechanical, thermal, structural and morphological properties of CGPM active films were investigated. ME has shown a marked influence on the optical, thermal properties and swelling behaviour of CGPM active films. The improvement in the tensile strength of CGPM-1 active film (53.7 MPa) was observed compared to control CS/GG/PVA (CGP) film. DSC study revealed that glass transition temperature (Tg) and melting temperature (Tm) decreased with the addition of ME in the CGP matrix, which confirmed the miscibility among the components of active films. There was an improvement in the thermal stability of the CGPM active films. The FTIR study confirmed the molecular interaction between ME and CS/GG/PVA matrix. The XRD analysis showed a decrease in crystallinity with an increase in the ratio of CS for CGPM active films. The CGPM active films were an excellent barrier to UV- light and have exhibited a decrease in moisture adsorption and water solubility compared to CGP control film. The inclusion of ME in the CGP matrix leads to the formation of a dense compact surface, which in turn enhanced hydrophobicity of active films. The CGPM active films showed minimum WVP, OP values and overall migration values were within the limits of 10 mg/dm2. It was also observed that CGPM active films effectively inhibited the growth of E. coli and S. aureus bacteria. These findings suggest CGPM active films are biodegradable, biocompatible, non-toxic and hence can find application as food packaging materials.

Antisolvent versus ultrasonication: Bottom-up and top-down approaches to produce lignin nanoparticles (LNPs) with tailored properties

In spite of the increasing amount of literature on the production and application of lignin nanoparticles (LNPs), little or no attention has been paid so far to the influence of different production methods on the properties of these nanostructures. Herein, we propose a comprehensive study to assess the impact of several factors on the color, morphology, colloidal stability, antioxidant capacity, and UV-shielding performance of LNPs. LNPs were obtained by two different routes: a bottom-up approach based on the self-assembly in a solvent-antisolvent system with acetone/lignin/water; or a top-down approach based on the ultrasonication of never-dried lignin aqueous suspensions. The starting lignin was extracted from elephant grass leaves or stems, so that the influence of anatomical origin and molecular weight could also be investigated. Moreover, lignin was oxidized prior to being converted into LNPs, allowing for comparisons between different oxidation degrees. This study showed that interesting properties of LNPs can be easily tailored and combined focusing on the various applications of these versatile nanostructures. In a model application, different types of LNPs were incorporated into poly(vinyl alcohol)-based nanocomposites, modulating the UV-protection capability of the polymer matrix.

Innovative production of lignin nanoparticles using deep eutectic solvents for multifunctional nanocomposites

A green and simple lignin nanoparticles (LNPs) production strategy was developed using deep eutectic solvents (DES). The LNPs were formed with corncob alkali lignin by sequential DES dissolution and self-assembling process. Uniform size and spherical shape of LNPs were observed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), dynamic light scattering (DLS), zeta potential analyzer and gel permeation chromatography (GPC). Less than 100 nm of LNPs were formed, and these particles were preserved without significant size-increase or precipitation within 30 days. The nanocomposite films prepared by incorporating the LNPs into biodegradable poly(vinyl alcohol) (PVA) matrix display good mechanical properties (tensile strength of 82.5 MPa and breaking strain of 103.3%), excellent UV-blocking (100% shielding of the UV spectrum region), strong hydrophobicity (static contact angle of 117.0°) and relatively high thermal stability (the maximum thermal weight loss temperature increased by 40 °C). Overall, this study not only facilitates the advancement of lignin-based nanotechnology by DES but also paves the way for the PVA polymer composites as potential food and medical packaging materials.

Antioxidant and UV-Blocking Properties of a Carboxymethyl Cellulose-Lignin Composite Film Produced from Oil Palm Empty Fruit Bunch

Oil palm empty fruit bunch (EFB) pulp with the highest cellulose content of 83.42% was obtained from an optimized process of acid pretreatment (0.5% v/v H2SO4), alkaline extraction (15% w/w NaOH), and hydrogen peroxide bleaching (10% w/v H2O2), respectively. The EFB cellulose was carboxymethylated, and the obtained carboxymethyl cellulose (CMC) was readily water-soluble (81.32%). The EFB CMC was blended with glycerol and cast into a composite film. Lignin that precipitated from the EFB black liquor was also incorporated into the film at different concentrations, and its effect on the UV-blocking properties of the film was determined. Interestingly, the EFB CMC film without lignin addition completely blocked UV-B transmittance. The incorporation of lignin at all concentrations significantly enhanced the UV-A blocking and other physical properties of the film, including the surface roughness, thickness, and thermal stability, although the tensile strength and water vapor permeability were not significantly affected. Complete UV-A and UV-B blocking were observed when lignin was added at 0.2% (w/v), and the film also exhibited the highest antioxidant activity against 2,2-diphenyl-1-picrylhydrazyl (DPPH) free radicals with an half-maximal inhibitory concentration (IC50) value of 3.87 mg mL-1.

State-of-the-Art: Applications and Industrialization of Lignin Micro/Nano Particles

As a new product of high-value utilization of lignin, lignin micro/nano particles (LMNPs) have attracted the attention of researchers due to their non-toxicity, corrosion-resistance, UV resistance, and other excellent characteristics and potential application value. This article outlined the main preparation methods of LMNPs at the current stage, summarized and compared them from three perspectives of preparation technology, final product state and product composition. Subsequently, based on the different focuses of the properties of LMNPs, their application research progress as fillers, UV blockers, drug delivery carriers, among others, were introduced. Then a concise analysis of the technical and economic assessment and life cycle assessment of LMNPs in the process of industrialization was made. Finally, the main problems at present and the future development directions were analyzed and prospected to provide references for the deep processing of forest resources and the development of bio-based nanomaterials.

Hydroxy citric acid cross-linked chitosan/guar gum/poly(vinyl alcohol) active films for food packaging applications

The present work aims to prepare Chitosan (CS)/Guar gum (GG)/Poly(vinyl alcohol) (PVA) cross-linked with Hydroxy citric acid (HCA) (CGPH active film) by solvent casting technique. The influence of HCA on different CS/PVA ratio (1:3, 1:1, 3:1) in presence of the fixed amount of GG (0.2%) was investigated. The analysis of the results showed that the addition of HCA to the different ratio of CS/PVA increased the degradation temperature and improved the mechanical properties of CGPH active films. FTIR spectra and XRD analysis revealed strong interactions among the components of CGPH active films. The analysis of SEM images and water contact angle suggested a compact, dense film surface with hydrophobic nature. Further, all the active films have shown a decrease in water vapour permeability (WVP) and acted as a barrier to UV-light. CGPH active films effectively inhibited the growth of S. aureus and E. coli bacteria. With all these features the CGPH active films can find application in food packaging.

Migration and Degradation in Composting Environment of Active Polylactic Acid Bilayer Nanocomposites Films: Combined Role of Umbelliferone, Lignin and Cellulose Nanostructures

This study was dedicated to the functional characterization of innovative poly(lactic acid) (PLA)-based bilayer films containing lignocellulosic nanostructures (cellulose nanocrystals (CNCs) or lignin nanoparticles (LNPs)) and umbelliferone (UMB) as active ingredients (AIs), prepared to be used as active food packaging. Materials proved to have active properties associated with the antioxidant action of UMB and LNPs, as the combination of both ingredients in the bilayer formulations produced a positive synergic effect inducing the highest antioxidant capacity. The results of overall migration for the PLA bilayer systems combining CNCs or LNPs and UMB revealed that none of these samples exceeded the overall migration limit required by the current normative for food packaging materials in both non-polar and polar simulants. Finally, all the hydrophobic monolayer and bilayer films were completely disintegrated in composting conditions in less than 18 days of incubation, providing a good insight on the potential use of these materials for application as active and compostable food packaging.

UV Protective, Antioxidant, Antibacterial and Compostable Polylactic Acid Composites Containing Pristine and Chemically Modified Lignin Nanoparticles

Polylactic acid (PLA) films containing 1 wt % and 3 wt % of lignin nanoparticles (pristine (LNP), chemically modified with citric acid (caLNP) and acetylated (aLNP)) were prepared by extrusion and characterized in terms of their overall performance as food packaging materials. Morphological, mechanical, thermal, UV–Vis barrier, antioxidant and antibacterial properties were assayed; appropriate migration values in food simulants and disintegration in simulated composting conditions were also verified. The results obtained indicated that all lignin nanoparticles succeeded in conferring UV-blocking, antioxidant and antibacterial properties to the PLA films, especially at the higher filler loadings assayed. Chemical modification of the fillers partially reduced the UV protection and the antioxidant properties of the resulting composites, but it induced better nanoparticles dispersion, reduced aggregates size, enhanced ductility and improved aesthetic quality of the films through reduction of the characteristic dark color of lignin. Migration tests and disintegration assays of the nanocomposites in simulated composting conditions indicated that, irrespectively of their formulation, the multifunctional nanocomposite films prepared behaved similarly to neat PLA.

Lignin nanoparticles enter the scene: A promising versatile green tool for multiple applications

Strategies to take advantage of residual lignin from industrial processes are well regarded in the field of green chemistry and biotechnology. Quite recently, researchers transformed lignin into nanomaterials, such as nanoparticles, nanofibers, nanofilms, nanocapsules and nanotubes, attracting increasing attention from the scientific community. Lignin nanoparticles are seen as green way to use high-value renewable resources for application in different fields because recent studies have shown they are non-toxic in reasonable concentrations (both in vitro and in vivo assays), inexpensive (a waste generated in the biorefinery, for example, from the bioethanol platform) and potentially biodegradable (by fungi and bacteria in nature). Promising studies have tested lignin nanoparticles for antioxidants, UV-protectants, heavy metal absorption, antimicrobials, drugs carriers, gene delivery systems, encapsulation of molecules, biocatalysts, supercapacitors, tissue engineering, hybrid nanocomposites, wound dressing, and others. These nanoparticles can be produced from distinct lignin types and by different chemical/physical/biological methods, which will result in varied characteristics for their morphology, shape, size, yield and stability. Therefore, taking into account that the theme "lignin nanoparticles" is a trending topic, this present review is emerging and has the discuss the current status, covering from concepts, the formation mechanism, synthesis methods and applications, to the future perspectives and challenges linked to lignin-based nanomaterials, aiming at the viability and commercialization of this biotechnological product.

Lignin-Based Nanoparticles: A Review on Their Preparations and Applications

Lignin is the most abundant by-product from the pulp and paper industry as well as the second most abundant natural renewable biopolymer after cellulose on earth. In recent years, transforming unordered and complicated lignin into ordered and uniform nanoparticles has attracted wide attention due to their excellent properties such as controlled structures and sizes, better miscibility with polymers, and improved antioxidant activity. In this review, we first introduce five important technical lignin from different sources and then provide a comprehensive overview of the recent progress of preparation techniques which are involved in the fabrication of various lignin-based nanoparticles and their industrial applications in different fields such as drug delivery carriers, UV absorbents, hybrid nanocomposites, antioxidant agents, antibacterial agents, adsorbents for heavy metal ions and dyes, and anticorrosion nanofillers.

Towards lignin derived thermoplastic polymers

Lignin is the second most abundant biobased material found on earth. It is produced mainly as a byproduct of pulp and paper industry and biorefineries. Despite its abundance, lignin valorization is not achieved on a large scale. Recently, there has been a growing demand for using the renewable and biodegradable raw materials in the commodity polymers. Potential use of lignin as a component in thermoplastic polymers is a promising approach for its value-added utilization. Given the vast applications of thermoplastic materials, there is lack of comprehensive review on lignin based thermoplastic polymers in literature. This review focuses on the utilization of lignin as functional and structural component of the thermoplastic polymers which requires structural modifications of lignin pertaining to the polymeric system. First, various lignin modifications were discussed in view of controlling the homogeneity, reactivity, processability and compatibility of lignin for successful thermoplastic copolymer synthesis and blend processing. Then, various copolymerization methodologies of lignin applicable for thermoplastic monomers are reviewed. Lastly, the lignin based thermoplastic blends are discussed which covers the lignin blends with various thermoplastic polymers and the chemical modifications required to improve its compatibility in polymer matrix. Some of the promising potential applications and future perspectives to achieve the goal of lignin-based commercial thermoplastics polymers are addressed.

Technological advancement in the synthesis and applications of lignin-based nanoparticles derived from agro-industrial waste residues: A review

Over the years, lignin has drawn a great deal of interest for their potential use as bio-polymers due to the presence of high amount of phenolic compounds, non-polluting feature and cost-competitiveness as compared to synthetic polymers. However, in order to fast-track their development, different attempts are made towards the usage of lignin in nano form since it exhibits some unique properties in nanoscale range. The present review article provides a detail analysis on the recent advancement in the synthesis and applications of lignin nanoparticles (LNPs) derived from agro-industrial waste residues. In view of that, an in-depth morphological analysis was reviewed to assess the structural influence on the characteristics of LNPs. Further, application of LNPs is explored in different fields including bio-medical engineering, pharmaceuticals, skin-care products and food industries. Finally, the paper is concluded discussing various challenges associated with the synthesis, modification and development with an aspiration of futuristic developments. The readers of this review article will be highly benefitted after acquiring a comprehensive knowledge on LNPs and its different synthesis processes along with various applications.

Fabrication and characterization of lignin-xylan hybrid nanospheres as pesticide carriers with enzyme-mediated release property

Lignin nanospheres (LNPs) are an emerging high-value material platform to realize lignin valorization. The modification or introduction of new functions to LNPs is of great significance to expand its downstream applications. This work evaluated the technical feasibility of preparing lignin-xylan hybrid nanospheres (LXNPs) through a simple solution-based self-assembly process, with the goal of achieving the application as pesticide carriers for enzyme-mediated controlled release. Hybrid LXNPs with various weigh ratios (lignin to xylan, 3 : 1, 1 : 1, 1 : 3) were obtained using deep eutectic solvent-extracted condensed lignin and water-insoluble xylan fragments, which exhibited a nanosphere size of about 166-210 nm with considerable stability in the pH range of 4-10. LXNPs with lignin to xylan ratios of 3 : 1 and 1 : 1 showed well-defined core-shell structures with enriched hydroxyl groups on the surface. It was proposed that lignin could anchor xylan fragments through van der Waals force and hydrophobic interactions between lignin phenylpropanes and xylan molecular backbones, thus facilitating the self-assembly process for the formation of this specific spherical structure. The resulting hydrophobic LXNPs core enabled the facile encapsulation of the biological pesticide avermectin (AVM) with 57.9-67.0% efficiency using one-pot synthesis. When these AVM-encapsulated LXNPs were subjected to enzymatic hydrolysis using xylanase, considerable AVM release of 44.8-55.1% was achieved after 16 h, in comparison to the 4.1% release only for those without xylanase. This work showed the high promise of fabricating hybrid LXNPs through the self-assembly process and also provided a universal nanosphere carrier for drug encapsulation and subsequent enzyme-mediated controlled release.