Chitosan/(polyvinyl alcohol)/zeolite electrospun composite nanofibrous membrane for adsorption of Cr6+, Fe3+ and Ni2

Enhancing mechanical properties of chitosan/PVA electrospun nanofibers: a comprehensive review

This review examines strategies to enhance the mechanical properties of chitosan/polyvinyl alcohol (PVA) electrospun nanofibers, recognized for their biomedical and industrial applications. It begins by outlining the fundamental properties of chitosan and PVA, highlighting their compatibility and mechanical characteristics. The electrospinning process is discussed, focusing on how various parameters and post-treatment methods influence fiber formation and performance. Key strategies for improvement are analyzed, including material modifications through blending and structural modifications like fiber orientation and multilayer constructions, and surface modifications such as coating and functionalization. The review also covers advanced characterization methods to evaluate mechanical properties and provides a comparative analysis of different enhancement approaches. Applications in biomedical and industrial contexts are explored, showcasing the versatility and innovation potential of these nanofibers. Finally, current challenges are addressed, and future research directions are proposed to overcome these obstacles and further enhance the mechanical properties of chitosan/PVA electrospun nanofibers, guiding their development for practical applications.

Gallic acid-functionalized chitosan composite for efficient removal of hexavalent chromium in aqueous

To address the pH limitations of traditional Cr(VI) adsorbents, converting Cr(VI) anions into the more stable Cr(III) cations through a reduction reaction is an effective strategy. Therefore, in this study, gallic acid (GA), with a high redox potential, was selected as the reducing agent, together with chitosan (CS) as the substrate, and sodium alginate (SA) as the gelling agent. A novel SCG composite material was successfully prepared using the sol-gel crosslinking method, which efficiently captured and reduced Cr(VI) while immobilizing Cr(III). At pH = 4, t = 150 min, and T = 30 °C, 1 g/L of SCG can remove 94.7 % of Cr(VI), with a reduction rate of 67.5 %, achieving efficient and stable Cr(VI) removal over a wide pH range. Furthermore, the SCG material demonstrated good pH adaptability (It can still remove 84 % of Cr(VI) at pH = 7) and practical applicability. Comparative experiments and DFT calculation results showed that the introduction of GA not only helped form a more compact network structure but also interacted synergistically with CS, significantly promoting the removal of Cr(VI). In conclusion, the SCG composite material provides a new approach for the treatment of Cr(VI)-contaminated wastewater.

Exploration of magnetic zeolite thin film derived from coal fly ash an efficient sorbent: Application to water treatment

Fly ash, produced during coal combustion for energy making, which is recognized as an industrial by-product, could lead to environmental health hazards. Subsequently, fly ash found that an exceptional adsorption performance for the removal of various toxic pollutants, the adsorption capacity of fly ash might be altered by introducing physical/chemical stimulation. Successfully converting fly ash into zeolites not only recovers their disposal difficulties but also transforms unwanted materials into merchandisable products for various industrial applications. Here we fabricated that, converting fly ash into zeolite and then modifying it with aminopropyl imidazole (ionic liquid), the imidazolium-based zeolite will be used as a template for loading Fe3O4 NPs. The formation of Fe3O4 NPs decorated zeolites is incorporated with polymeric materials [including polystyrene sulphonate (PSS), polyvinyl alcohol (PVA) and chitosan], producing to magnetic film (named Fe3O4 NPs@zeolite film). The fabricated magnetic film exhibits excellent functionality and durability for the sorption of chromium, selenium and organic dyes such as Congo red, RhB. These toxic contaminates were electrostatically bonded through adsorbent due to their protonation of below the pHzpc 7.0 with surface functional groups from imidazolium cationic moiety (R-N+), amino groups derived chitosan (-N, -NH and -NH2), and hydroxyl groups (Fe-OH), electrostatically bind with anionic selenium species are [(SeO32-, Se(IV)), and (SeO42- Se(VI)], chromium species HCrO4-, Cr2O72- and CrO42- the maximum removal performance were achieved in a wide pH range are highly suitable for practical application.

Chitosan-based composite featuring dual cross-linking networks for the removal of aqueous Cr(VI)

To avoid the environmental detriment caused by Cr(VI) waste, this study constructs a dual cross-linking network structure using sodium alginate (SA) and polyvinyl alcohol (PVA). Chitosan (CS) is further introduced through electrostatic attraction and hydrogen bonding and SA/PVA/CS (SPC) composite with porous structure is successfully prepared for the removal of Cr(VI) from wastewater. Batch adsorption experiments show that SPC has excellent adsorption capacity and practical usability with a broad pH applicability range. Under optimal adsorption conditions (pH = 2, t = 150 min, T = 35 °C, m/V = 2 g/L, C0 = 10 mg/L), the Cr(VI) removal rate of SPC achieves 89.2 %. Adsorption kinetics and isotherm models indicate that the adsorption process is primarily multi-layer and chemical adsorption. Additionally, FT-IR and XPS reveal that the adsorption mechanism of SPC for Cr(VI) involves a synergy of electrostatic attraction, reduction, ion exchange and complexation. Density functional theory (DFT) simulations also confirm the dominant role of CS in the Cr(VI) adsorption. In summary, SPC shows great potential for Cr(VI) wastewater treatment.

Ponceau 4R elimination from fruit juice: An integrated optimization strategy utilizing artificial neural networks, least squares, and chitosan-nickel ferrite Nano Sorbent

The goal of present work is to examine the efficiency of aminated-chitosan/NiFe2O4 nanoparticles (AmCs/NiFe2O4 NPs) produced for removing Ponceau 4R (P4R) from fruit juice through an adsorption process. The resulting nanoparticles were characterized using various techniques. The modeling of results was done using least squares (LS) and Radial basis function-artificial neural network (RBF-ANN). The optimum removal of P4R (91.43 %) was obtained at the following optimum conditions: pH 4.47, adsorbent dosage 0.047 g/L, contact time approximately 57.78 min, and initial concentration P4R 26.89 mg/L. The highest adsorption capacity (qm) was found to be 208.33 mg g-1. The P4R adsorption mostly followed the Freundlich and pseudo-second-order isotherm kinetic models. Both LS-based models and RBF-ANN provided good predictions for independent variables. The dye elimination efficacy for juice samples were approximately 90.34 %. Therefore, based on the obtained results, it can be claimed that the prepared AmCs/NiFe2O4 NPs can be used to remove P4R.

Surface Modifications of Superparamagnetic Iron Oxide Nanoparticles with Chitosan, Polyethylene Glycol, Polyvinyl Alcohol, and Polyvinylpyrrolidone as Methylene Blue Adsorbent Beads

Due to the negative impacts the dye may have on aquatic habitats and human health, it is often found in industrial effluent and poses a threat to public health. Hence, to solve this problem, this study developed magnetic adsorbents that can remove synthetic dyes like methylene blue. The adsorbent, in the form of beads, consists of a polymer blend of chitosan, polyethylene glycol, polyvinyl alcohol, polyvinylpyrrolidone, and superparamagnetic iron oxide nanoparticles (average size of 19.03 ± 4.25 nm). The adsorption and desorption of MB from beads were carried out at pH values of 7 and 3.85, respectively. At a concentration of 9 mg/L, the loading capacity and the loading amount of MB after 5 days peaked at 29.75 ± 1.53% and 297.48 ± 15.34 mg/g, respectively. Meanwhile, the entrapment efficiency of MB reached 29.42 ± 2.19% at a concentration of 8 mg/L. The cumulative desorption capacity of the adsorbent after 13 days was at its maximum at 7.72 ± 0.5%. The adsorption and desorption kinetics were evaluated.

Sustainable Zn2+ removal using highly efficient, novel, and cost-effective chitosan-magnetic biochar composite

This study focused on the development of a sustainable and low-cost adsorbent derived from the chitosan-biochar composite for the removal of Zn2+ from an aqueous solution. Biochar was prepared from cotton stalk residue by pyrolysis at 600 °C for 2 h, modified with FeCl3, and composed with chitosan in various ratios (1:3, 1:1, 3:1), leading to the formation of an efficient, thermally stable, and rich with functional groups chitosan-biochar composite denoted as CHB-Fe-CS. Functional groups (hydroxyl, carboxyl, and amine) were identified as key contributors to the adsorption mechanism. Langmuir isotherm (R2 = 0.99) and Pseudo-Second order (R2 = 0.99) were best fitted models with the experimental results indicating chemisorption-driven monolayer adsorption. The results revealed CHB-Fe-CS (3:1) composite obtained the highest adsorption capacity of 117.50 mg/g for Zn2+ under optimal conditions viz., 180 min batch time, 500 mg/l metal concentration, 4 g/l adsorbent dosage, 40 °C solution temperature, and 5.0 pH. Regeneration of the used adsorbent was performed using 0.2 mol/l HCl and obtained desorption efficiency of 67.48% and 51.48% after the 4th and 8th cycles. The adsorption mechanisms were dominated by ion exchange, surface complexation, and electrostatic attraction compared to intra-particle diffusion and physisorption. The CHB-Fe-CS demonstrated an economical, environment friendly, and good performing adsorbent for water decontamination.

Functionally responsive hydrogels with salt-alkali sensitivity effectively target soil amelioration

The long-standing crisis of soil salinization and alkalization poses a significant challenge to global agricultural development. High soil salinity-alkalinity, water dispersion, and nutrient loss present major hurdles to soil improvement. Novel environmentally friendly gels have demonstrated excellent water retention and slow-release capabilities in agricultural enhancement. However, their application for improving saline-alkali soil is both scarce and competitive. This study proposes a new strategy for regulating saline-alkali soil using gel-coated controlled-release soil modifiers (CWR-SRMs), where radical-polymerized gels are embedded on the surface of composite gel beads through spray coating. Characterization and performance analysis reveal that the three-dimensional spatial network structure rich in hydrophilic groups exhibits good thermal stability (first-stage weight loss temperature of 257.7 °C in thermogravimetric analysis) and encapsulation efficiency for fulvic acid‑potassium (FA-K), which can enhance soil quality in saline-alkali environments. The molecular chain relaxation under saline-alkali conditions promotes a synergistic effect of swelling and slow release, endowing it with qualifications as a water reservoir, Ca2+ source unit, and slow-release body. The results of a 6 weeks incubation experiment on 0-20 cm saline-alkaline soil with different application gradients showed that the gradient content had a significant effect on the soil improvement effect. Specifically, the T2 (the dosage accounted for 1 % of soil mass) treatment significantly increases water retention (30 % ~ 90 %), and nutrient levels (30 % ~ 50 %), while significantly decreasing soil sodium colloid content (30 % ~ 60 %) and soil pH (10 % ~ 15 %). Furthermore, PCA analysis indicates that the addition of 1 % CWR-SRMs as amendments can significantly adjust the negative aspects of soil salinity and alkalinity. This highlights the excellent applicability of CWR-SRMs in improving saline-alkali agricultural ecosystems, demonstrating the potential value of novel environmentally friendly gels as an alternative solution for soil challenges persistently affected by adverse salinity and alkalinity.

Recent trends in wastewater treatment by using metal-organic frameworks (MOFs) and their composites: A critical view-point

Respecting the basic need of clean and safe water on earth for every individual, it is necessary to take auspicious steps for waste-water treatment. Recently, metal-organic frameworks (MOFs) are considered as promising material because of their intrinsic features including the porosity and high surface area. Further, structural tunability of MOFs by following the principles of reticular chemistry, the MOFs can be functionalized for the high adsorption performance as well as adsorptive removal of target materials. However, there are still some major concerns associated with MOFs limiting their commercialization as promising adsorbents for waste-water treatment. The cost, toxicity and regenerability are the major issues to be addressed for MOFs to get insightful results. In this article, we have concise the current strategies to enhance the adsorption capacity of MOFs during the water-treatment for the removal of toxic dyes, pharmaceuticals, and heavy metals. Further, we have also discussed the role of metallic nodes, linkers and associated functional groups for effective removal of toxic water pollutants. In addition to conformist overview, we have critically analyzed the MOFs as adsorbents in terms of toxicity, cost and regenerability. These factors are utmost important to address before commercialization of MOFs as adsorbents for water-treatment. Finally, some future perspectives are discussed to give directions for potential research.

Modeling sunset yellow removal from fruit juice samples by a novel chitosan-nickel ferrite nano sorbent

Analysis of food additives is highly significant in the food industry and directly related to human health. This investigation into the removal efficiency of sunset yellow as an azo dye in fruit juices using Chitosan-nickel ferrite nanoparticles (Cs@NiFe2O4 NPs). The nanoparticles were synthesized and characterized using various techniques. The effective parameters for removing sunset yellow were optimized using the response surface methodology (RSM) based on the central composite design (CCD). Under the optimum conditions, the highest removal efficiency (94.90%) was obtained for the initial dye concentration of 26.48 mg L-1 at a pH of 3.87, a reaction time of 67.62 min, and a nanoparticle dose of 0.038 g L-1. The pseudo-second-order kinetic model had a better fit for experimental data (R2 = 0.98) than the other kinetic models. The equilibrium adsorption process followed the Freundlich isotherm model with a maximum adsorption capacity of 212.766 mg g-1. The dye removal efficiency achieved for industrial and traditional fruit juice samples (91.75% and 93.24%), respectively, confirmed the method's performance, feasibility, and efficiency. The dye adsorption efficiency showed no significant decrease after five recycling, indicating that the sorbent has suitable stability in practical applications. variousThe synthesized nanoparticles can be suggested as an efficient sorbent to remove the sunset yellow dye from food products.

Amphiphilic polyphenol incorporated hydrogel derived from mucoadhesive of Dillenia indica: Potential antioxidant and adsorbent

In this work, the mucoadhesive substances from the fruits and seeds of Dillenia indica (DI), a plant present abundantly in India, have been extracted and utilised to prepare a hydrogel. A synthetically prepared amphiphilic polyphenol (L) has been incorporated within the hydrogel network to enhance the hydrogelation property. Moreover, the DI-L hydrogel's total phenolic content and radical scavenging prospects have been investigated. The DI-L hydrogel has shown good, sensitive, and efficient adsorptive removal of Fe(III) from the aqueous medium with an adsorption capacity of 6.157 mg/g for an initial concentration of 10 mg/L of Fe(III) solution. As a result, these findings elucidate the most innovative application of transforming fruit mucoadhesive into sustainable environmental solutions.

Graphene oxide@Fe3O4-decorated iota-carrageenan composite for ultra-fast and highly efficient adsorption of lead (II) from water

The aggravated problem of lead pollution, especially in aquatic environments, necessitates the development of eminent adsorbents that could radically solve this environmental problem. Hence, a new composite was constructed based on iota carrageenan (i.Carr), graphene oxide (GO) and magnetite (Fe3O4) for removing noxious Pb2+ ions. The GO@Fe3O4-i.Carr composite was characterized by VSM, SEM, XPS, XRD, FTIR and Zeta potential. The removal of Pb2+ ions attained a quick equilibrium of almost 30 min with a removal efficiency reaching 93.68 %. The removal of Pb2+ was boosted significantly, in the order of GO@Fe3O4-i.Carr(1:1) > GO@Fe3O4-i.Carr(1:3) > GO@Fe3O4-i.Carr(3:1). Moreover, acquired experimental data fitted the pseudo 2nd order kinetic model and Freundlich isotherm model with a maximal monolayer adsorption capacity reached 440.05 mg/g. Notably, after five adsorption runs, the composite maintained its removal efficiency exceeding 74 %. The assumed adsorption mechanisms of Pb2+ onto GO@Fe3O4-i.Carr were complexation, precipitation, Lewis acid-base, and electrostatic attraction forces. Overall, the GO@Fe3O4-i.Carr composite elucidated the auspicious adsorbent criteria, comprising fast adsorption with high performance, ease-separation and tolerable recyclability, advising its feasible use to decontaminate water bodies from hazardous heavy metals.

Development of Novel PET-PAN Electrospun Nanocomposite Membrane Embedded with Layered Double Hydroxides Hybrid for Efficient Wastewater Treatment

Layered double hydroxides (LDHs) with their unique structural chemistry create opportunities to be modified with polymers, making different nanocomposites. In the current research, a novel PET-PAN embedded with Mg-AI-LDH-PVA nanocomposite membrane was fabricated through electrospinning. SEM, EDX, FTIR, XRD, and AFM were carried out to investigate the structure and morphology of the nanocomposite membrane. The characterization of the optimized nanocomposite membrane showed a beadless, smooth structure with a nanofiber diameter of 695 nm. The water contact angle and tensile strength were 16° and 1.4 Mpa, respectively, showing an increase in the hydrophilicity and stability of the nanocomposite membrane by the addition of Mg-Al-LDH-PVA. To evaluate the adsorption performance of the nanocomposite membrane, operating parameters were achieved for Cr(VI) and methyl orange at pH 2.0 and pH 4.0, respectively, including contact time, adsorbate dose, and pollutant concentration. The adsorption data of the nanocomposite membrane showed the removal of 68% and 80% for Cr(VI) and methyl orange, respectively. The process of adsorption followed a Langmuir isotherm model that fit well and pseudo-2nd order kinetics with R2 values of 0.97 and 0.99, respectively. The recycling results showed the membrane's stability for up to five cycles. The developed membrane can be used for efficient removal of pollutants from wastewater.

Advances in electrospun materials for the adsorption and separation of environmental pollutants: A comprehensive review

Despite a broad range of new techniques developed, adsorption methods remain one of the technologies of choice for the removal of contaminants. However, significant progress has also been made in these, which finds reflection in a new spectrum of adsorbents that can be used. This comprehensive review discusses properties, advantages, and perspectives on the use of custom-made electrospun adsorbents in the processes of heavy metals, agrochemicals, and microplastic contaminants removal from the environment. It presents the versatility and adaptability of materials that can be used as electrospun fibers matrix, also considering the mechanism and parameters of the sorption process carried out with them. The presented review proves, that due to the use of new, custom-made sorbents, such as electrospun materials, the adsorption processes still possess great application potential and development opportunities to provide an attractive and effective alternative to other remediation techniques.

One-Step Fabrication of Recyclable Konjac Glucomannan-Based Magnetic Nanoparticles for Highly Efficient Cr(VI) Adsorption

Recently, the natural polymer polysaccharide konjac glucomannan (KGM) has received attention as a promising adsorbent in water treatment due to its low toxicity, cost-effectiveness and biocompatibility. However, the high-level water absorbency of KGM makes it difficult to recover in water treatment. In this study, by combining KGM with magnetic nanoparticles, KGM-based magnetic nanoparticles (KGM-Fe3O4 NPs) with excellent adsorption properties and recyclability for heavy metals were prepared using an one-step precipitation method. The as-prepared KGM-Fe3O4 NPs have a spherical morphology of superparamagnetism with a small particle size (ca. 7.0 nm) and a large specific surface area (160.1 m2·g-1). Taking Cr(VI) as the target heavy metal ion, the above nanoparticles have a high adsorption capacity and fast adsorption rate for Cr(VI). The pseudo-second order kinetic model is more suitable to describe the adsorption process of Cr(VI) by KGM-Fe3O4 NPs, and the maximum adsorption capacity of Cr(VI) onto KGM-Fe3O4 NPs was calculated to be 41.67 mg·g-1 using the Langmuir isotherm model. In addition, KGM-Fe3O4 NPs with adsorbed heavy metal ions can be quickly recovered from a solution, regenerated, and reused in the next cycle. KGM-based Fe3O4 nanoparticles are promising adsorbents that show significant reusability for the removal of metal ions in water and wastewater treatment.

Zirconium/lanthanum-modified chitosan/polyvinyl alcohol composite adsorbent for rapid removal of fluoride

A novel and easily separable adsorbent in the shape of a membrane for the rapid removal of fluoride from water was prepared after testing Zr, La and LaZr to modify a chitosan/polyvinyl alcohol composite adsorbent (CS/PVA-Zr, CS/PVA-La, CS/PVA-LA-Zr). The CS/PVA-La-Zr composite adsorbent can remove a large amount of fluoride within 1 min of contact time, and the adsorption equilibrium can be reached within 15 min. The fluoride adsorption behavior of the CS/PVA-La-Zr composite can be described by pseudo-second-order kinetics and Langmuir isotherms models. The morphology and structure of the adsorbents were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The adsorption mechanism was studied using Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS), and which showed that ion exchange occurred mainly with hydroxide and fluoride ions. This study showed that an easily operable, low-cost and environmentally friendly CS/PVA-La-Zr has the potential to remove fluoride effectively from drinking water in a short time.

Preparation of polyamidoamine dendrimer-functionalized chitosan beads for the removal of Ag(I), Cu(II), and Pb(II)

Chitosan bead grafted by third-generation dendrimers (CB-G3) with a diameter of 1.40 mm was synthesized to investigate their performance in recovering Ag(I), Cu(II), and Pb(II) ions in aqueous media. The prepared adsorbents were characterized by XRD, FT-IR, elemental analysis, TGA, and SEM, and the effects of pH, contact time, concentration, and temperature were examined. The results showed that the adsorbents were successfully fabricated. The optimum pH value was 5, and the increased generation number contributed to adsorption capacity improvement, indicating that electrostatic interactions between amine groups and metal ions are the governing mechanism of adsorption by the CB-G3. The kinetics, isotherms, and thermodynamics of Ag(I), Cu(II), and Pb(II) adsorption onto the CB-G3 were investigated. The adsorption processes can be described using pseudo-second-order kinetic and Langmuir models. The maximum monolayer adsorption capacities were 105.62, 88.82, and 97.87 mg·g^-1 for Ag(I), Cu(II), and Pb(II) at 30 °C within 210 min, respectively. Electrostatic interactions and hydrogen bonds are the main mechanisms between metal ions and N atoms. Therefore, the CB-G3 is a promising candidate for Ag(I), Cu(II), and Pb(II) adsorption owing to its splendid ability in easy separation, good adsorptivity, and reusability for efficiently adsorbing Ag(I), Cu(II), and Pb(II) ions.

Electrospun Nanofiber Membrane: An Efficient and Environmentally Friendly Material for the Removal of Metals and Dyes

With the rapid development of nanotechnology, electrospun nanofiber membranes (ENM) application and preparation methods have attracted attention. With many advantages such as high specific surface area, obvious interconnected structure, and high porosity, ENM has been widely used in many fields, especially in water treatment, with more advantages. ENM solves the shortcomings of traditional means, such as low efficiency, high energy consumption, and difficulty in recycling, and it is suitable for recycling and treatment of industrial wastewater. This review begins with a description of electrospinning technology, describing the structure, preparation methods, and factors of common ENMs. At the same time, the removal of heavy metal ions and dyes by ENMs is introduced. The mechanism of ENM adsorption on heavy metal ions and dyes is chelation or electrostatic attraction, which has excellent adsorption and filtration ability for heavy metal ions and dyes, and the adsorption capacity of ENMs for heavy metal ions and dyes can be improved by increasing the metal chelation sites. Therefore, this technology and mechanism can be exploited to develop new, better, and more effective separation methods for the removal of harmful pollutants to cope with the gradually increasing water scarcity and pollution. Finally, it is hoped that this review will provide some guidance and direction for research on wastewater treatment and industrial production.

Interfacial Coordinational Bond Triggered Photoreduction Membrane for Continuous Light-Driven Precious Metals Recovery

Chemical/electric energy-driven processes dominate the traditional precious metal (PM) recovery market. The renewable energy-driven selective PM recycling approach crucial for carbon neutrality is under exploration. Herein, via an interfacial structure engineering approach, coordinational-active pyridine groups are covalently integrated onto the photoactive semiconductor SnS₂ surface to construct Py-SnS₂. Triggered by the preferred coordinational binding force between PMs and pyridine groups, together with the photoreduction capability of SnS₂, Py-SnS₂ shows significantly enhanced selective PM-capturing performance toward Au³⁺, Pd⁴⁺, and Pt⁴⁺ with recycling capacity up to 1769.84, 1103.72, and 617.61 mg/g for Au³⁺, Pd⁴⁺, and Pt⁴⁺, respectively. Further integrating the Py-SnS₂ membrane into a homemade light-driven flow cell, 96.3% recovery efficiency was achieved for continuous Au recycling from a computer processing unit (CPU) leachate. This study reported a novel strategy to fabricate coordinational bonds triggered photoreductive membranes for continuous PM recovery, which could be expanded to other photocatalysts for broad environmental applications.

Advanced Polymeric Nanocomposite Membranes for Water and Wastewater Treatment: A Comprehensive Review

Nanomaterials have been extensively used in polymer nanocomposite membranes due to the inclusion of unique features that enhance water and wastewater treatment performance. Compared to the pristine membranes, the incorporation of nanomodifiers not only improves membrane performance (water permeability, salt rejection, contaminant removal, selectivity), but also the intrinsic properties (hydrophilicity, porosity, antifouling properties, antimicrobial properties, mechanical, thermal, and chemical stability) of these membranes. This review focuses on applications of different types of nanomaterials: zero-dimensional (metal/metal oxide nanoparticles), one-dimensional (carbon nanotubes), two-dimensional (graphene and associated structures), and three-dimensional (zeolites and associated frameworks) nanomaterials combined with polymers towards novel polymeric nanocomposites for water and wastewater treatment applications. This review will show that combinations of nanomaterials and polymers impart enhanced features into the pristine membrane; however, the underlying issues associated with the modification processes and environmental impact of these membranes are less obvious. This review also highlights the utility of computational methods toward understanding the structural and functional properties of the membranes. Here, we highlight the fabrication methods, advantages, challenges, environmental impact, and future scope of these advanced polymeric nanocomposite membrane based systems for water and wastewater treatment applications.

Recent progress on electrospun nanofibrous polymer membranes for water and air purification: A review

Developing new polymer membranes with excellent thermal, mechanical, and chemical stability has shown great potential for various environmental remediation applications such as wastewater treatment and air filtration. Polymer membranes have been widely investigated over the past years and utilized to overcome severe ecological issues. Membrane-based technologies play a critical role in water purification and air filtration with the ability to act efficiently and sustainably. Electrospun nanofiber membranes have displayed excellent performance in removing various contaminants from water, such as bacteria, dyes, heavy metals, and oil. These nanofibrous membranes have shown good potential to filter the air from tiny particles, volatile organic compounds, and toxic gases. The performance of polymer membranes can be enhanced by fine-tuning polymer structure, varying surface properties, and strengthening overall membrane porosity. In this review, we discuss the involvement of electrospun nanofibrous membranes in different environmental remediation applications. It further reviews the recent progress of polymer membrane development by utilizing nanoparticles and naturally occurring polymers.

Ion-Imprinted Chitosan-Based Localized Surface Plasmon Resonance Sensor for Ni2+ Detection

Heavy metals are important sources of environmental pollution and cause disease in organisms throughout the food chain. A localized surface plasmon resonance sensor was proposed and demonstrated to realize Ni2+ detection by using ion-imprinted chitosan. Au nanoparticles were coated on the multimode fiber to excite the local surface plasmon resonance, and Ni2+-imprinted chitosan was then functionalized by using the dip coating technique. Ethylene diamine tetra-acetic acid was used to release the Ni2+ ions and hence form countless voids. Ni2+ was refilled into the voids to increase the refractive index of the sensing material, thus realizing the measurement of Ni2+ by monitoring the wavelength shift in the localized surface plasmon resonant peak. The coating thickness of the Ni2+-chitosan gel was optimized to obtain greater sensitivity. Experimental results show that the proposed Ni2+ sensor has a sensitivity of 185 pm/μM, and the limit of detection is 0.512 μM. The comparison experiments indicated that the ion-imprinted chitosan has better selectivity than pure chitosan.

A novel nanofibrous PAN ultrafiltration membrane embedded with ZIF-8 nanoparticles for effective removal of Congo red, Pb(II), and Cu(II) in industrial wastewater treatment

A novel Polyacrylonitrile (PAN) composite membrane involving ZIF-8 nanoparticles, named as ZIF-8/PAN membrane, was obtained via electrospinning to remove the Congo red (CR), Pb(II) and Cu(II) ions in industrial wastewaters, during which the adsorption mechanisms were examined in this study. The adsorption efficiency of the electrospun ZIF-8/PAN membrane was as high as 89%, 92% and 76% for CR, Pb(II) and Cu(II), respectively. Comparative analysis showed that ZIF-8 nanoparticles embedded in the ZIF-8/PAN membrane accounted for these enhanced adsorption capabilities. The adsorption behaviors of the ZIF-8 nanoparticles were investigated through experiments and theoretical analysis, and the results unraveled that the adsorption for CR by the ZIF-8 was mainly including electrostatic interaction, hydrogen bonding and π-π interaction, while those for Pb(II) and Cu(II) were mainly caused by ion-exchange and chemical adsorption. Parametric studies were conducted to optimize the conditions for removing CR, Pb(II), and Cu(II) by ZIF-8 nanoparticles, during which all of pollutants showed different reactions to the solution pH. This work not only develops a novel ZIF-8/PAN composite membrane for effective removals of pollutants, but also reveals the underlying mechanisms of pollutants adsorption in terms of molecular interactions, providing important understandings on fibrous materials design for efficient heavy metals and dyes removals in industrial wastewater treatment.

Efficient Removal of Organic Dye from Aqueous Solution Using Hierarchical Zeolite-Based Biomembrane: Isotherm, Kinetics, Thermodynamics and Recycling Studies

Bio adsorbents have received tremendous attention due to their eco-friendly, cheap and non-toxic nature. Recently, bio-adsorbent-based membranes have been frequently employed for water treatment. The work reports the preparation of a novel adsorbent membrane from hierarchical zeolite, polyvinyl alcohol, carboxymethyl cellulose and agar. The fabricated membrane was characterized spectroscopically and microscopically with several techniques such as XRD, UTM, TGA, optical microscopy and FT-IR, as well as contact-angle studies. The result showed that the hierarchical-zeolite-loaded membrane is superior in terms of thermal stability, mechanical properties and surface roughness. The fabricated membrane was investigated for its efficiency in the removal of Congo red dye in aqueous conditions. The influence of pH, temperature, contact period and the initial concentration of dye and zeolite loading on the adsorption process are also explored. The adsorption results highlighted the maximum sorption property of Congo red on agar/zeolite/carboxymethyl cellulose/polymer biomembrane was found to be higher (15.30 mg/g) than that of zeolite powder (6.4 mg/g). The adsorption isotherms and kinetic parameters were investigated via Langmuir, Freundlich and pseudo-first order, pseudo-second order and the intraparticle diffusion model, respectively. The adsorption isotherms fitted well for both considered isotherms, whereas pseudo-second order fitted well for kinetics. The thermodynamic parameter, ΔG at 303 K, 313 K and 323 K was −9.12, −3.16 and −0.49 KJ/mol, respectively. The work further explores the antibacterial efficacy of the prepared membrane and its reusability.

Use of polypyrrole-polystyrene membranes for extracting DNA from plant tissues

We describe the preparation of a membrane composed of polypyrrole-polystyrene (PPy-PS) and its application in DNA extraction. We adopted the electrospinning technique to prepare polystyrene (PS) membranes, which we used as substrates for incorporating polypyrrole chains through an in situ chemical procedure. As a model system, we initially investigated the use of PPy-PS membranes for the extraction of salmon sperm DNA from aqueous solutions. These studies have shown that the PPy-PS membrane has a maximum adsorption capacity of 236.0 mg of DNA per gram of PPy after 30 min of exposure to a DNA solution (100 mg/L). We incorporated the PPy-PS membranes into centrifugation columns, which we used to carry out experiments for extracting and purification of DNA from curly lettuce leaves. The protocol was initially optimized by first examining the most appropriate concentration of the three components of the lysis buffer (Tris/HCl, NaCl, and EDTA-Na). We then investigated the most adequate volumes of the concentrated surfactant solution (SDS 20%) and that used in the protein and polysaccharide precipitation step (5 M potassium acetate, pH 6.3), factors that directly influence the quality and quantity of the fraction of DNA obtained. For curly lettuce leaves, both in their mature and young stages, the yield and purity of the DNA purified using the PPy-PS membrane were comparable to those obtained using a commercial kit. In both cases, the collected DNA samples presented excellent integrity and quality. These results are suggestive that these composite membranes are competitive with the commercial kits available for the extraction and purification of DNA from plants.

A Review on Electrospun Poly(amino acid) Nanofibers and Their Applications of Hemostasis and Wound Healing

The timely and effective control and repair of wound bleeding is a key research issue all over the world. From traditional compression hemostasis to a variety of new hemostatic methods, people have a more comprehensive understanding of the hemostatic mechanism and the structure and function of different types of wound dressings. Electrospun nanofibers stand out with nano size, high specific surface area, higher porosity, and a variety of complex structures. They are high-quality materials that can effectively promote wound hemostasis and wound healing because they can imitate the structural characteristics of the skin extracellular matrix (ECM) and support cell adhesion and angiogenesis. At the same time, combined with amino acid polymers with good biocompatibility not only has high compatibility with the human body but can also be combined with a variety of drugs to further improve the effect of wound hemostatic dressing. This paper summarizes the application of different amino acid electrospun wound dressings, analyzes the characteristics of different materials in preparation and application, and looks forward to the development of directions of poly(amino acid) electrospun dressings in hemostasis.

Preparation of aminated porous polyacrylonitrile nanofibers as adsorbent for methyl orange removal

In this study, porous electrospinning polyacrylonitrile nanofiber (PPAN) surface functionalization with amine groups is studied for methyl orange (MO) dye removal from aqueous solution. A series of adsorption experiments were carried out to investigate the influence of initial solution pH value, contact time, initial solution concentration, and adsorption temperature on the adsorption performance. The experimental results showed that the removal of MO on these PPAN-PEI and PPAN-TEPA nanofibrous mats was a pH-dependent process with the maximum adsorption capacity at the initial solution pH of 3, and that the PPAN-PEI and PPAN-TEPA nanofibrous mats could be regenerated successfully after 4 recycling processes. The adsorption equilibrium data were all fitted well to the Langmuir isotherm equation, with maximum adsorption capacity of 1414.52 mg g⁻¹ and 1221.09 mg g⁻¹ for PPAN-PEI and PPAN-TEPA, respectively. The kinetic study indicated that the adsorption of MO could be well fitted by the pseudo-second-order equation and Weber–Morris model. Thermodynamic parameters such as free energy, enthalpy, and entropy of adsorption of the MO were also evaluated, and the results showed that the adsorption was a spontaneous exothermic adsorption process.

Amino functionalized porous polyacrylonitrile electrospun nanofibers were fabricated, which have good adsorption performance for MO in an acidic environment.

Electrospun Nanofiber-Based Membranes for Water Treatment

Water purification and water desalination via membrane technology are generally deemed as reliable supplementaries for abundant potable water. Electrospun nanofiber-based membranes (ENMs), benefitting from characteristics such as a higher specific surface area, higher porosity, lower thickness, and possession of attracted broad attention, has allowed it to evolve into a promising candidate rapidly. Here, great attention is placed on the current status of ENMs with two categories according to the roles of electrospun nanofiber layers: (i) nanofiber layer serving as a selective layer, (ii) nanofiber layer serving as supporting substrate. For the nanofiber layer's role as a selective layer, this work presents the structures and properties of conventional ENMs and mixed matrix ENMs. Fabricating parameters and adjusting approaches such as polymer and cosolvent, inorganic and organic incorporation and surface modification are demonstrated in detail. It is crucial to have a matched selective layer for nanofiber layers acting as a supporting layer. The various selective layers fabricated on the nanofiber layer are put forward in this paper. The fabrication approaches include inorganic deposition, polymer coating, and interfacial polymerization. Lastly, future perspectives and the main challenges in the field concerning the use of ENMs for water treatment are discussed. It is expected that the progress of ENMs will promote the prosperity and utilization of various industries such as water treatment, environmental protection, healthcare, and energy storage.

Electrospun Composite Nanofiltration Membranes for Arsenic Removal

In recent years, significant attention has been paid towards the study and application of mixed matrix nanofibrous membranes for water treatment. The focus of this study is to develop and characterize functional polysulfone (PSf)-based composite nanofiltration (NF) membranes comprising two different oxides, such as graphene oxide (GO) and zinc oxide (ZnO) for arsenic removal from water. PSf/GO- and PSf/ZnO-mixed matrix NF membranes were fabricated using the electrospinning technique, and subsequently examined for their physicochemical properties and evaluated for their performance for arsenite–As(III) and arsenate–As(V) rejection. The effect of GO and ZnO on the morphology, hierarchical structure, and hydrophilicity of fabricated membranes was studied using a scanning electron microscope (SEM), small and ultra-small angle neutron scattering (USANS and SANS), contact angle, zeta potential, and BET (Brunauer, Emmett and Teller) surface area analysis. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) were used to study the elemental compositions and polymer-oxide interaction in the membranes. The incorporation of GO and ZnO in PSf matrix reduced the fiber diameter but increased the porosity, hydrophilicity, and surface negative charge of the membranes. Among five membrane systems, PSf with 1% ZnO has the highest water permeability of 13, 13 and 11 L h−1 m−2 bar−1 for pure water, As(III), and As(V)-contaminated water, respectively. The composite NF membranes of PSf and ZnO exhibited enhanced (more than twice) arsenite removal (at 5 bar pressure) of 71% as compared to pristine PSf membranes, at 43%, whereas both membranes showed only a 27% removal for arsenate.

Molecular Dynamics Beyond the Monolayer Adsorption as Derived from Langmuir Curve Fitting

Langmuir adsorption model is a classic physical-chemical adsorption model and is widely used to describe the monolayer adsorption behavior at the material interface in environmental chemistry. Traditional adsorption dynamic modeling solely considered the surface physiochemical interaction between the adsorbent and adsorbate. The surface reaction dynamics resulting from the heterogeneous surface and intrinsic electronic structure of absorbents were rarely considered within the reported adsorption experiments. Herein, by employing the chlorine hybrid graphene oxide (GO-Cl) to adsorb Ag⁺ in an aqueous solution, complicated molecular dynamics significantly deviated from the monolayer adsorption mechanism, as suggested by Langmuir adsorption curve fitting, has been elucidated down to atomic scale. In the time-dependent Ag adsorption experiments, both Ag single atoms and Ag/AgCl nanoparticle heterostructures are observed to be formed sequentially on GO-Cl. These observations indicate that for the surface adsorption dynamics, not only the surface chemical adsorption process involved but also photoreduction and the C-Cl bond cleavage reaction has been heavily engaged within the GO-Cl interface, suggesting a much more complicated vision rather than the monolayered adsorption algorithm as derived from curve fitting. This study uses GO-Cl as a simple example to disclose the complicated adsorption dynamic process underneath Langmuir adsorption curve fitting. It advocates the necessity of imaging the interfacial atomic-scale dynamic structure with high-resolution microscopy techniques in modern adsorption studies, rather than simply explaining the adsorption dynamics relying on the curve fitting results due to the complicated physiochemical reactivity of the adsorbents.

Development of Nylon 6 nanofibers modified with Cyanex-272 for cobalt recovery

With a worldwide ever increasing demand for metals, particularly for the manufacture of electronics and batteries, there is not only a concurrent need to recover these materials from their subsequent waste streams but also a need to make advancements to do this via development of more efficient and eco-friendly processes for metal recovery; solid-phase extraction can be considered a promising alternative to conventional processes. This work studied the production of novel nanofibers modified with Cyanex 272 and their application in the recovery of cobalt present in aqueous solution The nanofibers produced by forcespinning were characterized by SEM, FT-IR and TGA and the extraction of cobalt was evaluated by variation of the pH, solid:liquid (S:L) ratio, extraction time and Cyanex 272 content in the nanofibers. The best extraction efficiency was 99.96%, achieved under the following conditions: pH 8; (S:L) ratio of 1:200; 25% of Cyanex 272; Extraction time of 60 min. The maximum extraction capacity obtained was 15.46 mg Co/g of nanofiber and 70.15 mg Co/g of extractor. In successive reuse cycles, the results demonstrated that the extraction efficiency was maintained at over 85%. The findings showed that Nylon 6/Cyanex 272 nanofibers are a new robust and promising material for the recovery of heavy metals from aqueous solution, confirming that nanofibers have an efficiency similar to conventional liquid-liquid extraction, without the disadvantage of volatile organic compounds emissions generated by the use of organic diluents.

High-performance photocatalytic membranes for water purification in relation to environmental and operational parameters

Growing technologies, increasing population and environmental pollution lead to severe contamination of water and require advanced water treatment technologies. These aspects lead to the need to purify water with advanced smart materials. This paper reviews the recent advances (during the last 5 years) in photocatalytic composite membranes used for water treatment. For this purpose, the authors have reviewed the main materials used in the development of (photocatalytic membranes) PMs, environmental and operational factors affecting the performance of photocatalytic membranes, and the latest developments and applications of PMs in water purifications. The composite photocatalytic membranes show good performance in the removal and degradation of pollutants from water.

Study on the Performance of Composite Adsorption of Cu2+ by Chitosan/β-Cyclodextrin Cross-Linked Zeolite

In order to remove Cu2+ from wastewater, a kind of microsphere adsorbent (SCDO) with high efficiency for Cu2+ adsorption was prepared by the microdrop condensation method, where chitosan (CTS) and sodium alginate (SA) were used as the matrix to crosslink β-cyclodextrin (β-CD) and zeolite (Zeo). The structure and properties of SCDO were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Upon that, the adsorption performance of SCDO for Cu2+ was studied, in which the effects of pH, initial concentration, dosage, adsorption time and temperature were investigated. The results showed that the removal rate of Cu2+ reached 97.08%, and the maximum adsorption capacity was 24.32 mg/g with the temperature at 30 °C, the dosage of SCDO at 12 g/L, the initial concentration of Cu2+ at 100 mg/L, the pH of the solution at 6.0 and the adsorption time at 120 min, respectively. The adsorption process of Cu2+ by SCDO occurred in accordance with quasi-second-order kinetics model and Langmuir adsorption isotherm. After four repeats of continuous adsorption and desorption, the regenerative removal rate of Cu2+ could still reach 84.28%, which indicated that SCDO had outstanding reusability.

In-Depth Study of Heavy Metal Removal by an Etidronic Acid-Functionalized Layered Double Hydroxide

Sorption methodologies play a pivotal role in heavy metal removal to meet the global requirements for uninterrupted access to drinkable water. Standard sorption technologies lack efficiency due to weak adsorbent-metal interaction. To this end, a layered cationic framework material loaded with phosphonate was first fabricated by a facile intercalation method to capture hazardous metals from an aqueous solution. To inquire the removal mechanisms, batch experiments, detection technologies, and simulation calculations were employed to study the interactions at the interface of clay/water. Specifically, the functionalized layered double hydroxide possessed excellent chelation adsorption properties with Zn²⁺ (281.36 mg/g) and Fe³⁺ (206.03 mg/g), in which model fitting results revealed that the adsorption process was chemisorption and monolayer interaction. Further, the interfacial interaction between the phosphonate and clay surface was evaluated by molecular dynamics simulation, and a new concept named the interaction region indicator was used to characterize weak interaction and coordinate bonds. The deep insight into the chelation mechanism was visually presented via the orbital interaction diagram. In addition, the regeneration of the spent adsorbent, adsorption column test, and acute toxicity analysis demonstrated that the synthesized material has immense potential in terms of practical usage for the treatment of toxic pollutants. These results provide a novel path for researchers to properly understand the adsorption behavior.

A comprehensive review on electrospun nanohybrid membranes for wastewater treatment

Electrospinning, being a versatile and straightforward method to produce nanofiber membranes, has shown significant advancement in recent years. On account of the unique properties such as high surface area, high porosity, mechanical strength, and controllable surface morphologies, electrospun nanofiber membranes have been found to have a great potential in many disciplines. Pure electrospun fiber mats modified with different techniques of surface modification and additive incorporation have exhibited enhanced properties compared to traditional membranes and are even better than the as-prepared electrospun membranes. In this review, we have summarized recently developed electrospun nanohybrids fabricated by the incorporation of functional specific nanosized additives to be used in various water remediation membrane techniques. The adsorption, filtration, photocatalytic, and bactericidal capabilities of the hybrid membranes in removing common major water pollutants such as metal ions, dyes, oils, and biological pollutants have been discussed. Finally, an outlook on the future research pathways to fill the gaps existing in water remediation have been suggested.

Applications of Nano-Zeolite in Wastewater Treatment: An Overview

Nano-zeolite is an innovative class of materials that received recognition for its potential use in water and tertiary wastewater treatment. These applications include ion-exchange/sorption, photo-degradation, and membrane separation. The aim of this work is to summarize and analyze the current knowledge about the utilization of nano-zeolite in these applications, identify the gaps in this field, and highlight the challenges that face the wide scale applications of these materials. Within this context, an introduction to water quality, water and wastewater treatment, utilization of zeolite in contaminant removal from water was addressed and linked to its structure and the advances in zeolite preparation techniques were overviewed. To have insights into the trends of the scientific interest in this field, an in-depth analysis of the variation in annual research distribution over the last decade was performed for each application. This analysis covered the research that addressed the potential use of both zeolites and nano-zeolites. For each application, the characterization, experimental testing schemes, and theoretical analysis methodologies were overviewed. The results of the most advanced research were collected, summarized, and analyzed to allow an easy visualization and comparison of these research results. Finally, the gaps and challenges that face these applications are concluded.

Modification of naturally abundant resources for remediation of potentially toxic elements: A review

Water and soil contamination due to potentially toxic elements (PTEs) represents a critical threat to the global ecosystem and human health. Naturally abundant resources have significant advantages as adsorbent materials for environmental remediation over manufactured materials such as nanostructured materials and activated carbons. These advantages include cost-effectiveness, eco-friendliness, sustainability, and nontoxicity. In this review, we firstly compare the characteristics of representative adsorbent materials including bentonite, zeolite, biochar, biomass, and effective modification methods that are frequently used to enhance their adsorption capacity and kinetics. Following this, the adsorption pathways and sites are outlined at an atomic level, and an in-depth understanding of the structure-property relationships are provided based on surface functional groups. Finally, the challenges and perspectives of some emerging naturally abundant resources such as lignite are examined. Although both unamended and modified naturally abundant resources face challenges associated with their adsorption performance, cost performance, energy consumption, and secondary pollution, these can be tackled by using advanced techniques such as tailored modification, formulated mixing and reorganization of these materials. Recent studies on adsorbent materials provide a strong foundation for the remediation of PTEs in soil and water. We speculate that the pursuit of effective modification strategies will generate remediation processes of PTEs better suited to a wider variety of practical application conditions.

Multifunctional Membranes-A Versatile Approach for Emerging Pollutants Removal

This paper presents a comprehensive literature review surveying the most important polymer materials used for electrospinning processes and applied as membranes for the removal of emerging pollutants. Two types of processes integrate these membrane types: separation processes, where electrospun polymers act as a support for thin film composites (TFC), and adsorption as single or coupled processes (photo-catalysis, advanced oxidation, electrochemical), where a functionalization step is essential for the electrospun polymer to improve its properties. Emerging pollutants (EPs) released in the environment can be efficiently removed from water systems using electrospun membranes. The relevant results regarding removal efficiency, adsorption capacity, and the size and porosity of the membranes and fibers used for different EPs are described in detail.

Green method to synthesize magnetic zeolite/chitosan composites and adsorption of hexavalent chromium from aqueous solutions

This paper aims to synthesis a recyclable adsorbent from solid waste using a clean and environmentally friendly method to deal with Cr(VI) water pollution. Magnetic zeolite/chitosan composites (ZFA/MCS) were prepared by the neutralization method. The adsorption properties of ZFA/MCS, prepared by the neutralization method for Cr(VI) ions under different conditions especially cross-linking, were investigated in detail. The results showed that cross-linked ZFA/MCS generally showed higher adsorption capacity than uncross-linked ones. The uncross-linked ZFA/MCS and cross-linked ZFA/MCS showed a saturated adsorption capacity of 25.67 mg·g^-1 and 28.47 mg·g^-1 at pH = 3 and 30 °C, respectively. The experimental values were followed Langmuir adsorption equations and pseudo-second-order kinetic model, indicating that the adsorption was probably monolayer coverage and chemical adsorption, respectively. The effect of temperature proved that the adsorption was spontaneous and endothermic. Therefore, the adsorbent with excellent recyclability and adsorbability was successfully fabricated via a green synthetic strategy.

Multifunctional β-Cyclodextrin-EDTA-Chitosan polymer adsorbent synthesis for simultaneous removal of heavy metals and organic dyes from wastewater

Heavy metals and organic dyes are the major source of water pollution. Herein, a trifunctional β-cyclodextrin-ethylenediaminetetraacetic acid-chitosan (β-CD-EDTA-CS) polymer was synthesized using an easy and simple chemical route by the reaction of activated β-CD with CS through EDTA as a cross-linker (amidation reaction) for the removal of inorganic and organic pollutants from aqueous solution under different parameters such as pH, time effect, initial concentration, reusability, etc. The synthesized adsorbent was characterized using powder X-ray diffraction, Fourier transform infrared spectroscopy, field scanning electron microscopy, energy dispersive spectroscopy, Brunauer-Emmett-Teller (BET), thermogravimetric analyzer techniques to investigate their structural, functional, morphological, elemental compositions, surface area and thermal properties, respectively. Two types of heavy metals, i.e., mercury (Hg²⁺) and cadmium (Cd²⁺), and three organic dyes, i.e., methylene blue (MB), crystal violet (CV) and safranin O (SO) were chosen as inorganic and organic pollutants, respectively, to study the adsorption capacity of β-CD-EDTA-CS in aqueous solution. The β-CD-EDTA-CS shows monolayer adsorption capacity 346.30 ± 14.0 and 202.90 ± 13.90 mg g^-1 for Hg²⁺ and Cd²⁺, respectively, and a heterogeneous adsorption capacity 107.20 ± 5.70, 77.40 ± 5.30 and 55.30 ± 3.60 mg g^-1 for MB, CV and SO, respectively. Kinetics results followed pseudo-second order (PSO) kinetics behavior for both metal ions and dyes, and higher rate constants values (0.00161-0.00368 g mg^-1 min^-1) for dyes confirmed the cavitation of organic dyes (physisorption). In addition, we have also demonstrated the performance of β-CD-EDTA-CS for the of four heavy metals Hg²⁺, Cd²⁺, Ni²⁺, and Cu²⁺ and three dyes MB, CV, and SO in secondary treated wastewater. Findings of this study indicate that β-CD-EDTA-CS simple and essay to synthesize and can be use in wastewater treatment.