Removal of inorganic contaminants in soil by electrokinetic remediation technologies: A review

Mechanisms of heating-electrokinetic co-driven perfluorooctanoic acid (PFOA) adsorption on zeolite

Slow release of emerging contaminants limits their accessibility from soil to pore water, constraining the treatment efficiency of physio-chemical treatment sites. DC fields mobilize organic contaminants and influence their interactions with geo-matrices such as zeolites. Poor knowledge, however, exists on the joint application of heating and electrokinetic approaches on perfluorooctanoic acid (PFOA) transport in porous media. Here, we investigated electrokinetic PFOA transport in zeolite-filled percolation columns at varying temperatures. Variations of pseudo-second-order kinetic constants (kPSO) were correlated to the liquid viscosity variations (η) and elctroosmotic flow velocities (vEOF). Applying DC fields and elevated temperature significantly (>37%) decreased PFOA sorption to zeolite. A good correlation between η, vEOF, and kPSO was found and used to develop an approach interlinking the three parameters to predict the joint effects of DC fields and temperature on PFOA sorption kinetics. These findings may give rise to future applications for better tailoring PFOA transport in environmental biotechnology.

Transformation of sedimentary dissolved organic matter in electrokinetic remediation catalogued by FT-ICR mass spectrometry

In electrokinetic remediation (EKR), the sedimentary dissolved organic matter (DOM) could impede remediation by scavenging reactive species and generating unintended byproducts. Yet its transformation and mechanisms remained largely unknown. This study conducted molecular-level characterization of the water-extractable DOM (WEOM) in EKR using negative-ion electrospray ionization coupled to 21 tesla Fourier transform ion cyclotron resonance mass spectrometry (21 T FT-ICR MS). The results suggested that ∼55 % of the ∼7,000 WEOM compounds identified were reactive, and EKR lowered their diversity, molecular weight distribution, and double-bond equivalent (DBE) through a combination of electrochemical and microbial redox reactions. Heteroatom-containing WEOM (CHON and CHOS) were abundant (∼ 35% of the total WEOM), with CHOS generally being more reactive than CHON. Low electric potential (1 V/cm) promoted the growth of dealkylation and desulfurization bacteria, and led to anodic CO2 mineralization, anodic cleavage of -SO and -SO3, and cathodic cleavage of -SH2; high electric potential (2 V/cm) only enriched desulfurization bacteria, and differently, led to anodic oxygenation and cathodic hydrogenation of unsaturated and phenolic compounds, in addition to cathodic cleavage of -SH2. The long-term impact of these changes on soil quality and nitrogen-sulfur-carbon flux may be need to studied to identify unknown risks and new applications of EKR.

Effects of nitrogen regulation on heavy metal phytoextraction efficiency (Leucaena leucocephala): Application of a nitrogen fertilizer and a fungal agent

Lead (Pb) and cadmium (Cd) have been identified as the primary contaminants in soil, posing potential health threats. This study aimed to examine the effects of applying a nitrogen fertilizer and a fungal agent Trichoderma harzianum J2 (nitrogen alone, fungi alone, and combined use) on the phytoremediation of soils co-contaminated with Pb and Cd. The growth of Leucaena leucocephala was monitored in the seedling, differentiation, and maturity stages to fully comprehend the remediation mechanisms. In the maturity stage, the biomass of L. leucocephala significantly increased by 18% and 29% under nitrogen-alone (NCK+) and fungal agent-alone treatments (J2), respectively, compared with the control in contaminated soil (CK+). The remediation factors of Pb and Cd with NCK+ treatment significantly increased by 50% and 125%, respectively, while those with J2 treatment increased by 73% and 145%, respectively. The partial least squares path model suggested that the nitrogen-related soil properties were prominent factors affecting phytoextraction compared with biotic factors (microbial diversity and plant growth). This model explained 2.56 of the variation in Cd concentration under J2 treatment, and 2.97 and 2.82 of the variation in Pb concentration under NCK+ and J2 treatments, respectively. The redundancy analysis showed that the samples under NCK+ and J2 treatments were clustered similarly in all growth stages. Also, Chytridiomycota, Mucoromucota, and Ciliophora were the key bioindicators for coping with heavy metals. Overall, a similar remediation mechanism allowed T. harzianum J2 to replace the nitrogen fertilizer to avoid secondary pollution. In addition, their combined use further increased the remediation efficiency.

Iodide- and electrochemical assisted removal of mercury by Cirsium arvense from gold tailings in the Amansie West District, Ghana

Mercury (Hg) pollution in Ghana through mining has become a serious environmental challenge. This study investigates the potential of Cirsium arvense to photostabilize Hg using electrokinetic current with or without an iodide solution in gold mine tailings heavily contaminated through mining activities in southern Ghana. An initial Hg concentration of 9.60 mg/kg using cold vapor atomic absorption spectrometry (CVAAS) was determined. The biological absorption coefficient, bioconcentration factor, and translocation factor of Hg have been presented. Cirsium arvense therefore had a higher bioconcentration factor (BCF) of 2.6-5.15 mg/kg, and a transfer factor (TF) of 0.24-0.36 indicating a higher efficiency for phytostabilization. Both the rate and time of extractions of Hg from the tailings by Cirsium arvense are efficiently improved in the combined electric current and iodide treatment. Plant and electric current combined treatment and plant and iodide combined treatment had only 60 and 50% phytostabilization rates, respectively. The combined plant, iodide, and electric current treatment has proven to be superior with about >90% Hg removal rate. Therefore, the combined plant, iodide, and electric current treatment resulted in a higher Hg removal efficiency by Cirsium arvense in a shorter period due to higher solubilization rate and electromigration effects on Hg species.

Synergistic solidification and mechanism research of electrolytic manganese residue and coal fly ash based on C-A-S-H gel material

Electrolytic manganese residue (EMR) is known for high concentrations of Mn2+, NH4+, and heavy metals. Failure to undergo benign treatment and landfill disposal would undeniably lead to negative impacts on the quality of the surrounding ecological environment. This study sought to mitigate the latent environmental risks associated with EMR using a cooperative solidification/stabilization (S/S) method involving coal fly ash (CFA). Leveraging leaching toxicity tests, the leaching behavior of pollutants in electrolytic manganese residue-based geopolymer materials (EMRGM) was determined. At the same time, mechanistic insights into S/S processes were explored utilizing characterization techniques such as XRF, XRD, FT-IR, SEM-EDS, and XPS. Those results confirmed significant reductions in the leaching toxicities of Mn2+ and NH4+ to 4.64 μg/L and 0.99 mg/L, respectively, with all other heavy metal ions falling within the permissible limits set by relevant standards. Further analysis shows that most of NH4+ volatilizes into the air as NH3, and a small part is fixed in the EMRGM in the form of struvite; in addition to being oxidized to MnOOH and MnO2, Mn2+ will also be adsorbed and wrapped by silicon-aluminum gel together with other heavy metal elements in the form of ions or precipitation. This research undeniably provides a solid theoretical foundation for the benign treatment and resourceful utilization of EMR and CFA, two prominent industrial solid wastes.

Highly alkaline electrokinetic extraction: Characteristics of chromium mobilization, conversion and transport in high alkalinity soil

In site chromium (Cr) contaminated soil characterized by high alkalinity and carbonate content, protons are not effectively targeted for Cr(III) mobilization but rather accelerate the reduction of easily transportable Cr(VI) within the acidification electrokinetic (EK) system. As an alternative, the highly alkaline extraction conditions (HAECs) maintained by anolyte regulation are explored owing to the ability to desorb strong binding Cr(VI) and form anionic Cr(III)-hydroxides (Cr(OH)4-, Cr(OH)52-). The results demonstrate that HAECs were more efficient in mobilizing ions in severe alkalinity and electrical conductivity soil compared to organic acid acidifying extraction conditions (OAECs). Simultaneously, a limited amount of soluble Cr(III) was produced; however, its transportation was hindered and more noticeable in the case of Cr(VI), displaying a distinct retention phase within the intermediate soil chamber. The antagonistic interplay between electromigration and electroosmotic flow was considered the main responsible factor. The conversion intensity of Cr(VI) to Cr(III) was inhibited at HAECs. The promising mobilization and low conversion intensity contributed to total Cr removal. At HAECs, enhanced electromigration and electroosmotic flow combined with a favorable oxidation environment may facilitate in situ delivery of oxidants, offering practical implications for the EK detoxification of high alkalinity site soil contaminated with Cr. The practicability of HAECs is likely to be enhanced when the cost-benefit balance of providing a simultaneous energy supply during site treatment is resolved.

Recent trends in the phytoremediation of radionuclide contamination of soil by cesium and strontium: Sources, mechanisms and methods: A comprehensive review

This comprehensive review examines recent trends in phytoremediation strategies to address soil radionuclide contamination by cesium (Cs) and strontium (Sr). Radionuclide contamination, resulting from natural processes and nuclear-related activities such as accidents and the operation of nuclear facilities, poses significant risks to the environment and human health. Cs and Sr, prominent radionuclides involved in nuclear accidents, exhibit chemical properties that contribute to their toxicity, including easy uptake, high solubility, and long half-lives. Phytoremediation is emerging as a promising and environmentally friendly approach to mitigate radionuclide contamination by exploiting the ability of plants to extract toxic elements from soil and water. This review focuses specifically on the removal of 90Sr and 137Cs, addressing their health risks and environmental implications. Understanding the mechanisms governing plant uptake of radionuclides is critical and is influenced by factors such as plant species, soil texture, and physicochemical properties. Phytoremediation not only addresses immediate contamination challenges but also provides long-term benefits for ecosystem restoration and sustainable development. By improving soil health, biodiversity, and ecosystem resilience, phytoremediation is in line with global sustainability goals and environmental protection initiatives. This review aims to provide insights into effective strategies for mitigating environmental hazards associated with radionuclide contamination and to highlight the importance of phytoremediation in environmental remediation efforts.

Iron slag/activated carbon-electrokinetic system with anolyte recycling for single and mixture heavy metals remediation

The electrokinetic process has been proposed for in-situ soil remediation to minimize excavation work and exposure to hazardous materials. The precipitation of heavy metals in alkaline pH near the cathode is still challenging. Reactive filter media and enhancement agents have been used in electrokinetics to enhance the removal of heavy metals. This study investigated coupling industrial iron slag waste and iron slag-activated carbon reactive filter media with electrokinetic for a single and mixture of heavy metals treatment. Instead of using acid enhancement agents, the anolyte solution was recycled to neutralize the alkaline front at the cathode, reducing the operation cost and chemical use. Experiments were conducted for 2 and 3 weeks at 20 mA electric current. Copper removal increased from 3.11 % to 23 % when iron slag reactive filter media was coupled with electrokinetic. Copper removal increased to 70.14 % in the electrokinetic experiment with iron slag-activated carbon reactive filter media. The copper removal increased to 89.21 % when the anolyte solution was recycled to the cathode compartment. Copper removal reached 93.45 % when the reactive filter media-electrokinetic process with anolyte recirculation was extended to 3 weeks. The reactive filter media- an electrokinetic process with anolyte recycling was evaluated for removing copper, nickel, and zinc mixture, and results revealed 81.1 % copper removal, 89.04 % nickel removal, and 92.31 % zinc removal in a 3-week experiment. The greater nickel and zinc removal is attributed to their higher solubility than copper. The results demonstrated the cost-effectiveness and efficiency of the electrokinetic with iron slag-activated carbon reactive filter media with anolyte recirculation for soil remediation from heavy metals.

Peptides Used for Heavy Metal Remediation: A Promising Approach

In recent years, heavy metal pollution has become increasingly prominent, severely damaging ecosystems and biodiversity, and posing a serious threat to human health. However, the results of current methods for heavy metal restoration are not satisfactory, so it is urgent to find a new and effective method. Peptides are the units that make up proteins, with small molecular weights and strong biological activities. They can effectively repair proteins by forming complexes, reducing heavy metal ions, activating the plant's antioxidant defense system, and promoting the growth and metabolism of microorganisms. Peptides show great potential for the remediation of heavy metal contamination due to their special structure and properties. This paper reviews the research progress in recent years on the use of peptides to remediate heavy metal pollution, describes the mechanisms and applications of remediation, and provides references for the remediation of heavy metal pollution.

Spatiotemporal dynamic temperature variation dominated by ion behaviors during groundwater remediation using direct current

Direct current (DC) electric field has shown promising performance in contaminated site remediation, in which the Joule heating effect plays an important role but has been previously underappreciated. This study focuses on the spatiotemporal characteristics and mechanism of temperature change in heterogeneous porous media with applied DC. The heating process can be divided into four phases: preferential heating of the low permeability zone (LPZ), rapid heating in the middle region, temperature drop and hot zone shift, and reheating. The dynamic ion behaviors with complex interplays among reactions, electrokinetic-driven migration, and mixed convection induced an uneven redistribution of ions and dominated the heating rate and temperature distribution. The concentration of major ions near the pH jump decreased to 1% of the initial value, even though ions were continuously pumped into the heating zone. This ion depletion caused a drop in current, heating rate, and temperature. Here ions cannot be delivered rapidly into the ion-depleted zone by electromigration due to the potential flattening in the surrounding region. The presence of LPZ intensified the nonuniformity of ion redistribution, where a regional focusing of water-soluble ions was observed, and weakened the temperature rebound compared with that using homogeneous sand. These results provide a new perspective on the regulation of DC heating in site remediation.

The effects of different electrode materials on the electric field-assisted co-composting system for the soil remediation of heavy metal pollution

The electric field-assisted composting system (EACS) is an emerging technology that can enhance composting efficiency, but little attention has been given to electrode materials. Herein, an EACS was established to investigate the effects of electrode materials on humic substance formation and heavy metal speciation. Excitation-emission matrix analysis showed that carbon-felt and stainless-steel electrodes increased humic acid (HA) by 48.57 % and 47.53 %, respectively. In the EACS with the carbon-felt electrode, the bioavailability factors (BF) of Cu and Cr decreased by 18.00 % and 7.61 %, respectively. Despite that the stainless-steel electrodes decreased the BF of As by 11.26 %, the leaching of Cr, Ni, Cu, and Fe from the electrode itself is an inevitable concern. Microbial community analyses indicated that the electric field increased the abundance of Actinobacteria and stimulated the multiplication of heavy metal-tolerant bacteria. Redundancy analysis indicates that OM, pH, and current significantly affect the evolution of heavy metal speciation in the EACS. This study first evaluated the metal leaching risk of stainless-steel electrode, and confirmed that carbon-felt electrode is environment-friendly material with high performance and low risk in future research with EACS.

Construction of an effective method combining in situ capping with electric field-enhanced biodegradation for treating PAH-contaminated soil at abandoned coking sites

The simultaneous application of in situ capping and electro-enhanced biodegradation may be a suitable method for ensuring the feasibility and safety of reusing abandoned coking sites. However, the capping layer type and applied electric field pattern may affect the efficiency of sequestering and removing pollutants. This study investigated changes in electric current, soil moisture content and pH, polycyclic aromatic hydrocarbon (PAH) concentration, bacterial number, and microbial community structure and metabolic function during soil remediation at abandoned coking plant sites under different applied electric field patterns and barrier types. The results indicated that polarity-reversal electric field was more conducive to maintaining electric current, soil properties, resulting in higher microbial number, community diversity, and functional gene abundance. At 21d, the mean PAH concentrations in contaminated soil, the capping layer's clean soil and barrier were 78.79, 7.56, and 1.57 mg kg-1 lower than those with a unidirectional electric field, respectively. The mean degradation rate of PAHs in the bio-barrier was 10.12 % higher than that in the C-Fe barrier. In the experiment combining a polarity-reversal electric field and a bio-barrier, the mean PAH concentrations in contaminated soil and the capping layer were 706.68 and 27.15 mg kg-1 lower than those in other experiments, respectively, and no PAHs were detected in the clean soil, demonstrating that the combination of the polarity-reversal electric field and the bio-barrier was effective in treating soil at abandoned coking plant sites. The established method of combining in situ capping with electro-enhanced biodegradation will provide technical support for the treatment and reuse of heavily PAH-contaminated soil at abandoned coking plant sites.

Can rare earth elements be recovered from abandoned mine tailings by means of electrokinetic-assisted phytoextraction?

Given the high impact of traditional mining, the recovery of rare earth elements (REEs) from hazardous waste materials could become an option for the future in accordance with the principles of the circular economy. In this work, the technical feasibility of REEs recovery from metal mine tailings has been explored using electrokinetic-assisted phytoremediation with ryegrass (Lolium perenne L.). Phytoextraction combined with both AC current and DC current with reversal polarity was applied (1 V cm-1, 8 h day-1) to real mine tailings containing a total concentration of REEs (Sc, Y, La, Ce, Pr, and Nd) of around 146 mg kg-1. Changes in REEs geochemical fractionation and their concentrations in the soil pore water showed the mobilization of REEs caused by plants and electric current; REE availability was increased to a higher extent for combined electrokinetic-assisted phytoextraction treatments showing the relevant role of plants in the process. Our results demonstrated the initial hypothesis that it is feasible to recover REEs from real metal mining waste by phytoextraction and that the performance of this technology can be significantly improved by applying electric current, especially of the AC type, which increased REE accumulation in ryegrass in the range 57-68% as compared to that of the treatment without electric field application.

Migration and morphological transformation patterns of heavy metals on sludge cells and extracellular polymeric substances (EPS) under the influence of different treatments

The impediment of sludge resource utilization stems from the presence of heavy metals within the sludge matrix. To optimize heavy metal removal techniques from undried sludge, it is essential to study the distribution of heavy metals in the sludge flocs structure and the changes in morphology in the sludge cells after different treatments. In this study, the sludge was subjected to chemical treatments using citric acid (CA), EDTA, and saponin, as well as electrokinetic treatment at 2 V/cm. The distribution and migration of Cu, Ni, and Zn in sludge flocs after various treatment methods were analyzed. The heavy metals were found to migrate from intracellular to extracellular polymeric substances (EPS) without causing extensive sludge cell lysis. They gradually diffused outward with the dispersion of the EPS layer. The migration efficiency of the three heavy metals in the sludge flocs was Zn, Ni, and Cu. This was mainly related to the initial distribution and morphology of the heavy metals. Under the influence of chemicals and an electric field, the acid-soluble and reducible heavy metals in the cells partially migrated to the EPS, while the stable heavy metals transformed into an unstable state. Furthermore, the order of chemical reagents in terms of their effect on the migration efficiency of heavy metals was CA > EDTA > Saponin, owing to the varying binding strengths of heavy metals and their impact on the degree of loosening of the EPS. Especially after CA treatment a greater proportion of Cu, Ni, and Zn were transferred from the cells to the EPS. The acidification effect near the anode during electrokinetic treatment intensifies the migration of heavy metals. This study provides basic research for subsequent engineering optimization aimed at removing heavy metals from sludge.

Electrochemical remediation of synthetic and real marine sediments contaminated by PAHs, Hg and As under low electric field values

To date, remediation, protection, and restoration of contaminated sites is a global concern. The current technologies to restore sediments characterized by heterogeneous characteristics, several pollutants, fine grains, and low hydraulic permeability are poorly effective; hence their remediation is still challenging. A promising approach for the sediment's remediation could be the electrochemical route since it is a not-expensive, effective and noninvasive in situ technology. Electrochemical remediation (ER) is commonly studied under relatively high electric fields (E ≥ 1 V cm-1) and using costly processing fluids in a three compartments cell aiming to desorb and transport the contaminants into the processing fluids (secondary dangerous effluent). In this work, contaminated marine sediments were electrochemically treated focusing on the insertion of electrodes directly in the sediments and adopting, for the first time for real sediments, low E values (≤ 0.25 V cm-1) for 4-days period. It was observed that PAHs can be simultaneously transported and degraded in situ preventing the production of a secondary dangerous effluent and reducing the energy consumption. Firstly, clay marine sediments dragged from Capo Granitola Coast (Trapani, Italy) spiked with five PAHs congeners (5PAHs), Hg and As were used as a simplified model matrix and treated to simulate a real case study. A total PAHs removal efficiency of 57% was reached after 96 h of treatment under 0.05 V cm-1. Then, real polluted marine sediments from Augusta Bay (Syracuse) and Bagnoli-Coroglio Bay (Naples) in the southern Italy were treated as real contaminated sediments to be restored, to validate the proposed approach for real cases. A quite good removal efficiency of PAHs was reached after 96 h of electrochemical treatment coupled with a low energetic consumption due to the rather E values adopted. In addition, it was observed that this approach, under the adopted conditions, is unsuitable for the remediation of Hg and As.

Effect of experimental boundary conditions and treatment-time on the electro-desalination of soils

This study investigates the effect of boundary conditions and treatment-time on the electro-desalination of artificially-contaminated soil. The effect of ion exchange membranes (IEM), calcium chloride (CaCl2), and ethylenediaminetetraacetic acid (EDTA) on the removal of salt (i.e., Na+, Cl-, and Ca2+) and metal (i.e., Co2+ and Fe2+) ions from the soil by electrokinetic (EK) was studied. The outcomes demonstrate that an increase in treatment-time decreases the electroosmosis and ion removal rate, which might be attributed to the formation of acid-base fronts in soil, except in the IEM case. Because a high pH jump and electroosmotic flow (EOF) of water were not observed within the soil specimen due to the IEM, the removal of ions was only by diffusion and electromigration. The collision of acid-base fronts produced a large voltage gradient in a narrow soil region with a reduced electric field (EF) in its remaining parts, causing a decrease in EOF and ion transport by electromigration. The results showed that higher electroosmosis was observed by using CaCl2 and EDTA; thus, the removal rate of Co2+, Na+, and Ca2+ was greater than Cl- due to higher EOF. However, for relatively low EOF, the removal of Cl- exceeded that of Co2+, Na+, and Ca2+, possibly due to a lack of EOF. In addition, the adsorption of Fe2+ in soil increased with treatment-time due to the corrosion of the anode during all EK experiments except in the case of IEM, where an anion exchange membrane (AEM) was introduced at the anode-soil interface.

Technological and economic analysis of electrokinetic remediation of contaminated soil: A global perspective and its application in Indian scenario

Globally million hectares of land annually is getting contaminated by heavy metalloids like As, Cd, Cr, Hg, Pb, Co, Cu, Ni, Zn, and Se, with current concentrations in soil above geo-baseline or regulatory standards. The heavy metals are highly toxic, mobile, and persistent and hence require immediate and effective mitigation. There are many available remediation techniques like surface capping, encapsulation, landfilling, soil flushing, soil washing, electrokinetic extraction, stabilization, solidification, vitrification, phytoremediation, and bioremediation which have been evolved to clean up heavy metal-contaminated sites. Nevertheless, all of the technologies have some applicability and limitations making the soil remediation initiative unsustainable. Among the available technologies, electrokinetic remediation (EKR) has been comparatively recognized to mitigate contaminated sites via both in-situ and ex-situ approaches due to its efficiency, suitability for use in low permeability soil, and requirement of low potential gradient. The work critically analyzes the EKR concerning techno, economic, and sustainability aspect for evaluating its application on various substrates and environmental conditions. The current soil contamination status in India is presented and the application of EKR for the heavy metal remediation from soil has been evaluated. The present work summaries a comprehensive and exhaustive review on EKR technology proving its effectiveness for a country like India where the huge amount of waste generated could not be treated due to lack of infrastructure, technology, and economic constraints.

Enhancement of heavy metals desorption from the soil by eddy deep leaching in hydrocyclone

An eddy deep leaching technology was developed in this paper to address the challenge of treating heavy metal contaminants in industrial mining areas. The desorption effect of As, Cd, Sb and Pb was investigated utilizing chemical leaching and physical eddy techniques. It was found that the heavy metals concentration increased with decreasing particle size. The highest proportion of Cd in the form distribution of soil was in the bound to iron and manganese oxides, while the maximum proportion of As, Sb and Pb were in the residual. The optimal solid-liquid ratio of the hydrocyclone was 1:20, and the corresponding separation efficiency and flow rate were 84.7% and 1.76 m3/hr, respectively. The grade efficiency of soil particle separation increases with particle size and exceeds 99% for particles above 1,000 µm. Leaching experiments have revealed that oxalic acid (OA) and a combination of oxalic acid and EDTA (OAPE) were more efficient than citric acid (CA) and a combination of citric acid and EDTA (CAPE) for the desorption of heavy metals, respectively. The comparison of OAPE and eddy leaching found that the latter improved the desorption efficiency by 9.4%, 7.5%, 7.2% and 7.8% for As, Cd, Sb and Pb compared to the former, respectively. The results demonstrated that the eddy leaching technique could further enhance the desorption efficiency of heavy metals. It is expected to provide technical support for soil remediation with reduced usage of leaching agents.

Electrokinetic remediation for the removal of heavy metals in soil: Limitations, solutions and prospection

Electrokinetic remediation (EKR) technology is a promising method to remove heavy metals from low permeability soil, because it is environmentally friendly, efficient and economical, and can realize in-situ remediation. In this paper, the basic principles and related physical and chemical phenomena of EKR are systematically summarized, and three limiting problems of EKR technology are put forward: the weak ability of dissolving metals, focusing effect, and energy consumption. There are many methods to solve these technical problems, but there is a lack of systematic summary of the causes of problems and solutions. Based on various enhanced EKR technologies, this paper summarizes the main ideas to solve the limiting problems. The advantages and disadvantages of each technology are compared, which has guiding significance for the development of new technology in the future. This paper also discusses the dissolution of residual heavy metals, which is rare in other articles. The energy consumption of EKR and the remediation effect are equally important, and both can be used as indicators for evaluating the feasibility of new technologies. This paper reviews the influence of various electric field conditions on power consumption, such as renewable energy supply, new electrode materials and electrode configurations, suitable voltage values and functional electrolytes. In addition, a variety of energy consumption calculation methods are also introduced, which are suitable for ohmic heat loss, energy distribution when there is non-target ion competition, and power consumption of specific ions in various metal ions. Researchers can make selective reference according to their actual situations. This paper also systematically introduces the engineering design and cost calculation of EKR, lists the research progress of some engineering cases and pilot-scale tests, analyzes the reasons why it is difficult to apply EKR technology in large-scale engineering at present, and puts forward the future research direction.

Electrokinetic remediation of estuarine sediments using a large reactor: spatial variation of physicochemical, mineral, and chemical properties

The treatment and beneficial use of polluted or contaminated environmental matrices have become major issues, especially as the world strives toward a zero-waste policy. In this regard, dredged sediments need to be treated before they can be used in an environmentally safe and sustainable manner. Therefore, this work aims to treat estuarine sediments and, more importantly, use physicochemical, mineral, organic, and chemical information to understand the reactions that occur upon treatment. Dredged estuarine sediments were collected from Tancarville (Seine River estuary, France) and subjected to electrokinetic (EK) remediation using a 128-L laboratory-scale reactor. The sediments were treated 8 h per day for 21 days. The electric (voltage and current) and physicochemical (pH and electric conductivity) parameters were monitored during treatment. Sediments were collected from various sections in the reactor at the end of the experiment (lengthwise, widthwise, and depthwise). The spatial variation was investigated in terms of organic, mineral, and metal contents. Statistical analyses proved that the variation occurred only in the lengthwise direction. Furthermore, three main phases described the treatment, which were mainly linked to carbonate dissolution and pH variation. The results also showed that the trace elements Ni and Zn were reduced by 21% and 19%, respectively, without a direct link to pH, while Ca and Mg were only redistributed. The buffering capacity of the anodic sediment was reduced due to carbonate dissolution. The treated sediments showed reduced contents in trace metals without affecting major elements that can be useful in agriculture (i.e., Ca and Mg).

Applying a nanocomposite hydrogel electrode to mitigate electrochemical polarization and focusing effect in electrokinetic remediation of a Cu- and Pb-contaminated loess

Inappropriate handling of copper (Cu) and lead (Pb)-containing wastewater resulting from metallurgical and smelting industries in Northwest China encourages their migration to surrounding environments. Their accumulation causes damage to liver and kidney function. The electrokinetic (EK) technology is considered to be an alternative to traditional remediation technologies because of its great maneuverability. The EK remediation is accompanied by the electrode polarization and the focusing effect toward affecting removal efficiency. In this study, a nanocomposite hydrogel (NCH) electrode was proposed and applied to the EK remediation of Cu- and Pb-contaminated loess. The mechanical, adsorption capacity, adsorption kinetics, and electrochemical properties of the NCH electrode were investigated in detail, followed by microscopic analyses of Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectroscopy (EDS), and Raman spectrometer. Results showed that the enhancement of the mechanical properties of the NCH electrode was attributed to the crosslinks of graphene nanoparticles, calcium alginate, and hydrogen bonds, while the Cu or Pb adsorption by the NCH electrode was in a chemisorption manner. The second layer formation might address the increase in adsorption capacity with increasing temperature. These results highlight the relative merits of the NCH electrode and verify the potential of applying the NCH electrode to the EK remediation of Cu- and Pb-contamianted loess.

Tuning and Coupling Irreversible Electroosmotic Water Flow in Ionic Diodes: Methylation of an Intrinsically Microporous Polyamine (PIM-EA-TB)

Molecularly rigid polymers with internal charges (positive charges induced by amine methylation) allow electroosmotic water flow to be tuned by adjusting the charge density (the degree of methylation). Here, a microporous polyamine (PIM-EA-TB) is methylated to give a molecularly rigid anion conductor. The electroosmotic drag coefficient (the number of water molecules transported per anion) is shown to increase with a lower degree of methylation. Net water transport (without charge flow) in a coupled anionic diode circuit is demonstrated based on combining low and high electroosmotic drag coefficient materials. The AC-electricity-driven net process offers water transport (or transport of other neutral species, e.g., drugs) with net zero ion transport and without driver electrode side reactions.

Intuitionistic fuzzy-based entropy weight method-TOPSIS for multi-attribute group decision-making in drilling fluid waste treatment technology selection

Drilling fluid waste is produced by oil and gas industry operations and can potentially cause serious environmental pollution and energy consumption if not properly treated. Currently, there are several treatment methods available for drilling fluid waste such as bioremediation, thermal treatment, solidification/stabilization treatment, electrochemical remediation, physiochemical treatment, and supercritical fluid treatment. However, selecting an adequate method to treat drilling fluid waste is a critical consideration. The objective of this work is to analyze the problem of drilling fluid waste pollution and treatment methods, establish a drilling fluid waste treatment decision index system that takes into account various factors, and apply the intuitionistic fuzzy-based entropy weight method (EWM)-technique for order of preference by similarity to ideal solution (TOPSIS) method to make a multi-attribute group decision on drilling fluid waste treatment methods. The method is then applied to the WBQ004-1-H1 drilling project as an example for comprehensive analysis. The final decision results show that A3 (0.566) > A1 (0.537) > A6 (0.526) > A5 (0.485) > A4 (0.478) > A2 (0.447), so the solidification/stabilization treatment is the most suitable method for this project, providing new insights into selecting drilling fluid waste treatment methods in actual projects.

Permeable reactive composite approaching cathode enhanced Cr removal in soil using the byproduct of electrokinetic technology: emphasized energy utilization efficiency

Cost-effective techniques with significant removal rates and low energy consumption are urgently required for in-situ Cr-contaminated soil remediation to reduce potential environmental toxicity to the ecosystem and human bodies. Electrokinetic technology is a valuable and promising soil remediation technology; however, the acidic and alkaline fronts evolution induced by the electrokinetic byproducts (H+, OH-) has significant hindering characteristics for ion removal. To effectively utilize the byproducts for enhancing Cr elimination, this paper proposed the permeable reactive composite approaching cathode with rhamnolipid-modified biochar as reactive material. Power utilization efficiency (η) was presented to comprehensively evaluate the target species elimination effect, considering removal rate and energy consumption. Results suggested that biosurfactant rhamnolipid stimulated Cr removal in acid and base fronts. Acid front induced rhamnolipid protonation reducing anolyte Cr(VI) to Cr(III), and base front induced rhamnolipid deprotonation complexing with Cr(III) and expediting Cr(VI) dissolution by electrostatic repulsion. Permeable reactive composite approaching cathode induced the maximum removal rate of Cr(VI) and Cr(III) in each section by impelling the alkaline front. Approaching cathode caused increased resistance and energy consumption in the near-anode regions, ultimately decreasing energy utilization efficiency. Optimized moving frequency and applied potential magnitude could adjust power consumption distribution in a single soil layer to obtain better electrokinetic removal performance of contaminates. This work provided essential scientific and practical importance for in-situ electrokinetic remediation of Cr(VI) and Cr(III), considering elimination efficiency and energy consumption in the future.

Performance of electrokinetic remediation system for mercury contaminated marine sediment: Roles of electrode spacing and electrode configuration

Understanding mercury (Hg) species existing after electrokinetic remediation (EK) for marine-sediment remediation is limited. Herein, the Hg fraction removal of EK from contaminated marine sediment was investigated appertaining to bipolar electrode settings along with the effects of electrode spacing and configuration considered. Based on the selective sequential Hg extractions (Hg SSE), much of the Hg in the sediment originated from F5 (i.e., HgS) and F4 (i.e., HgO). The F5 fraction removed by EK was about 30 %, while the F4 fraction had a slight increase of about 34 %. When it comes to electrode configuration, a hexagonal pattern has a higher Hg removal performance than that of a rectangular shape. The addition of anodes increases the remediation surface area, thus allowing superior Hg removal. This study indicates that the electrode spacing significantly affects the mercury removal and the remediation time. Determining suitable spacing enhances the electrical potentials in the migration flux.

Effect of clay content on the mobilization efficiency of per- and polyfluoroalkyl substances (PFAS) from soils by electrokinetics and hydraulic flushing

The need for the efficient remediation of soils impacted by per- and polyfluoroalkyl substances (PFAS) is substantially growing because of the notable upsurge in societal and regulatory awareness of this class of chemicals. To remediate PFAS-contaminated soils using mobilization approaches, the choice of appropriate techniques highly depends on the soil's composition, particularly the clay content, which significantly affects the soil's permeability. Here, we investigated the PFAS mobilization efficiency from soils with different clay contents by using two techniques: electrokinetic (EK) remediation and hydraulic flushing. Artificial kaolinite was added to a loamy sand soil to prepare four soil blends with clay contents of 5, 25, 50, and 75%, each contaminated with perfluorooctanoic acid (PFOA) and perfulorooctanesulfonic acid (PFOA) at 10,000 μg/kg. EK remediation was conducted by applying a low voltage (30 V) with a current of 100 mA, and hydraulic flushing was carried out by applying a hydraulic gradient (HG) with a slope of 6.7%. Results show that, with a 14-day treatment duration, the EK-mobilization efficiency was enhanced substantially with the increase of clay content (removal of PFOS increased from 20% at 5% clay to 80% at 75% clay), most likely due to the increase of electroosmotic flow due to the higher content of particles having a zeta potential (i.e., clay). For HG, increasing the clay content significantly suppressed the mobilization of PFAS (removal of PFOS decreased from 40% at 5% clay to 10% at 75% clay) due to a notable decrease in the soil's permeability. Based on the results, applying hydraulic flushing and washing techniques for mobilizing PFAS would be appropriate when treating permeable soils with a maximum clay content of about 25%; otherwise, other suitable mobilization techniques such as EKs should be considered.

Electrokinetic Remediation of Zn-Polluted Soft Clay Using a Novel Electrolyte Chamber Configuration

This study investigated a novel electrolyte chamber configuration for heavy-metal-contaminated fine-grained soil to reduce the leakage of electrolyte solution and alleviate secondary pollution, finally promoting the electrokinetic remediation (EKR) potential to be scaled up for application. Experiments were conducted on clay spiked with Zn to investigate the feasibility of the novel EKR configuration and the effect of different electrolyte compositions on the electrokinetic remedial efficiency. The results show that the electrolyte chamber situated above the soil surface is promising for the remediation of Zn-contaminated soft clay. Using 0.2 M citric acid as the anolytes and catholytes was an excellent choice for pH control in the soil and the electrolytes. Through this, the removal efficiency in different soil sections was relatively uniform and more than 90% of the initial Zn was removed. The supplementing of electrolytes resulted in the water content in the soil being distributed evenly and finally sustained at approximately 43%. Consequently, this study proved that the novel EKR configuration is suitable for fine-grained soil contaminated with Zn.

Recent Progress on Ex Situ Remediation Technology and Resource Utilization for Heavy Metal Contaminated Sediment

Sediment is an important part of aquatic systems, which plays a vital role in transporting and storing metals. Due to its abundance, persistence, and environmental toxicity, heavy metal pollution has always been one of the hot spots in the world. In this article, the state-of-art ex situ remediation technology for metal-contaminated sediments is elaborated, including sediment washing, electrokinetic remediation (EKR), chemical extraction, biological treatment, as well as encapsulating pollutants by adding some stabilized/solidified materials. Furthermore, the progress of sustainable resource utilization methods, such as ecosystem restoration, construction materials (e.g., materials fill materials, partition blocks, and paving blocks), and agriculture use are reviewed in detail. Finally, the pros and cons of each technique are summarized. This information will provide the scientific basis for selecting the appropriate remediation technology in a particular scenario.

Preparation of a novel iron oxychloride (FeOCl) auxiliary electrode in promoting electrokinetic remediation of Cr(VI) contaminated soil: An experimental and DFT calculation analysis

The utilization of auxiliary electrode can improve substantially the electrokinetic remediation efficiency of heavy metal contaminated soil. The increase in the auxiliary electrode performance is the key to further promote the electrokinetic remediation efficiency. In this study, two kinds of auxiliary electrodes, pure FeOCl and doped FeOCl with W and S, were prepared and used in the electrokinetic remediation of Cr(VI) contaminated soil. The system equipped with the auxiliary electrode doped FeOCl brought more stable system current (202 mA) and more uniform electric field than blank group (130 mA). The reduction rate of Cr(VI) was increased by 50% due to the presence of Fe²⁺ and S^2-. The accelerating migration of ions by auxiliary electrode was responsible for the improvement in electrokinetic remediation efficiency. Density functional theory (DFT) calculation showed that Cl vacancy formation energies of pure FeOCl, S-doped FeOCl (S/FeOCl) and W-doped FeOCl (W/FeOCl) were 1.29, 1.15 and 1.49 eV respectively, and the ion diffusion barriers were 0.093, 0.099 and 0.148 eV respectively. Calculation results indicated that the doping of S was conducive to the diffusion of Cl ions, and the bonding of W-Cl was stronger than Fe-Cl. The charging and discharging process of auxiliary electrode became easier due to the formation of lower vacancy in S-doped FeOCl, which could bring a higher current for the electrokinetic remediation system. The electrochemical performance of FeOCl doped with W and S was improved obviously. This study provided a further explanation for the positive role of auxiliary electrode in electrokinetic remediation system.

Simultaneous stabilization of Pb, Cd, and As in soil by rhamnolipid coated sulfidated nano zero-valent iron: Effects and mechanisms

Sulfidation effectively improves the electron transfer efficiency of nanoscale zero-valent iron (nZVI), but decreases the specific surface area of nZVI. In this study, sulfidated nZVI (S-nZVI) coated with rhamnolipid (RL-S-nZVI) was synthesized and used to stabilize Pb, Cd, and As in combined polluted soil. The stabilization efficiency of 0.3% (wt) RL-S-nZVI to water soluble Pb, Cd, and As in soil reached 88.76%, 72%, and 63%, respectively. Rhamnolipid coating inhibited the reduction of specific surface area and successfully encapsulated nZVI, thus reducing the oxidation of Fe⁰. The types of iron oxides in RL-S-nZVI were reduced compared to S-nZVI, but the content and strength of Fe⁰ iron were obviously enhanced. Furthermore, rhamnolipid functional groups (-COOH and -COO^-) were also involved in the stabilization process. In addition, the stabilization efficiency of RL-S-nZVI to the bioavailable Pb, Cd, and As in soil increased by 41%, 41%, and 50%, respectively, compared with nZVI. The presence of organic acids, especially citric acid, improved the stabilization efficiency of RL-S-nZVI to the three metals. The result of BCR sequential extraction indicated that RL-S-nZVI increased the residual state of Pb, Cd, and As and reduced the acid-soluble and reducible state after 28 days of soil incubation. XRD and XPS analyses showed that the stabilization mechanisms of RL-S-nZVI on heavy metals involved in ion exchange, surface complexation, adsorption, co-precipitation, chemisorption, and redox.

In Situ Remediation Technology for Heavy Metal Contaminated Sediment: A Review

Sediment is an important part of the aquatic ecosystem, which involves material storage and energy exchange. However, heavy metal pollution in sediment is on the increase, becoming an important concern for the world. In this paper, the state-of-art in situ remediation technology for contaminated sediment was elaborated, including water diversion, capping, electrokinetic remediation, chemical amendments, bioremediation and combined remediation. The mechanisms for these techniques to reduce/immobilize heavy metals include physical, electrical, chemical and biological processes. Furthermore, application principle, efficiency and scope, advantages and disadvantages, as well as the latest research progress for each restoration technology, are systematically reviewed. This information will benefit in selecting appropriate and effective remediation techniques for heavy metal-contaminated sediment in specific scenarios.

The Role of pH, Electrodes, Surfactants, and Electrolytes in Electrokinetic Remediation of Contaminated Soil

Electrokinetic remediation has, in recent years, shown great potential in remediating polluted environments. The technology can efficiently remove heavy metals, chlorophenols, polychlorinated biphenyls, phenols, trichloroethane, benzene, toluene, ethylbenzene, and xylene (BTEX) compounds and entire petroleum hydrocarbons. Electrokinetic remediation makes use of electrolysis, electroosmosis, electrophoresis, diffusion, and electromigration as the five fundamental processes in achieving decontamination of polluted environments. These five processes depend on pH swings, voltage, electrodes, and electrolytes used in the electrochemical system. To apply this technology at the field scale, it is necessary to pursue the design of effective processes with low environmental impact to meet global sustainability standards. It is, therefore, imperative to understand the roles of the fundamental processes and their interactions in achieving effective and sustainable electrokinetic remediation in order to identify cleaner alternative solutions. This paper presents an overview of different processes involved in electrokinetic remediation with a focus on the effect of pH, electrodes, surfactants, and electrolytes that are applied in the remediation of contaminated soil and how these can be combined with cleaner technologies or alternative additives to achieve sustainable electrokinetic remediation. The electrokinetic phenomenon is described, followed by an evaluation of the impact of pH, surfactants, voltage, electrodes, and electrolytes in achieving effective and sustainable remediation.

Recent advances in soil remediation technology for heavy metal contaminated sites: A critical review

With the increasing development of industry and urbanization, heavy metal contaminated sites have become progressively conspicuous, particularly by unreasonable emissions from electroplating, nonferrous metals smelting, mine tailing, etc. In recent years, soil remediation technologies for heavy metal contaminated sites have developed rapidly. New and effective remediation technologies have emerged successively, and more successful practical applications have appeared. Therefore, systematical summarization of the current progress is essential. As a result, in this paper, some mainstream soil remediation technologies for heavy metal contaminated sites, including physical remediation (soil thermal desorption and soil replacement), bioremediation (phytoremediation and microbial remediation), chemical remediation (chemical leaching, chemical stabilization, electrokinetic remediation-permeable reactive barrier, and chemical oxidation/reduction), as well as various combined remediation are comprehensively reviewed. The influencing factors, advantages, disadvantages, remediation mechanism, and practical applications are also deeply discussed. Besides, the corresponding remediation strategies are put forward for the remediation of heavily polluted sites such as the chemical industry, smelting, and tailing areas. Overall, this review will be beneficial for the in-depth understanding and provide references for the reasonable selection and development of soil remediation technology for heavy metal contaminated sites.

Electrochemical Methods for Water Purification, Ion Separations, and Energy Conversion

Agricultural development, extensive industrialization, and rapid growth of the global population have inadvertently been accompanied by environmental pollution. Water pollution is exacerbated by the decreasing ability of traditional treatment methods to comply with tightening environmental standards. This review provides a comprehensive description of the principles and applications of electrochemical methods for water purification, ion separations, and energy conversion. Electrochemical methods have attractive features such as compact size, chemical selectivity, broad applicability, and reduced generation of secondary waste. Perhaps the greatest advantage of electrochemical methods, however, is that they remove contaminants directly from the water, while other technologies extract the water from the contaminants, which enables efficient removal of trace pollutants. The review begins with an overview of conventional electrochemical methods, which drive chemical or physical transformations via Faradaic reactions at electrodes, and proceeds to a detailed examination of the two primary mechanisms by which contaminants are separated in nondestructive electrochemical processes, namely electrokinetics and electrosorption. In these sections, special attention is given to emerging methods, such as shock electrodialysis and Faradaic electrosorption. Given the importance of generating clean, renewable energy, which may sometimes be combined with water purification, the review also discusses inverse methods of electrochemical energy conversion based on reverse electrosorption, electrowetting, and electrokinetic phenomena. The review concludes with a discussion of technology comparisons, remaining challenges, and potential innovations for the field such as process intensification and technoeconomic optimization.

Comparative Life-Cycle Cost Analysis of Alternative Technologies for the Removal of Emerging Contaminants from Urban Wastewater

Emerging contaminants (ECs) continue to threaten our fragile ecosystem, yet their mitigation remains limited by economic factors. Meanwhile, a relatively expensive material, Graphene Oxide (GO), has shown promise as a solution for EC removal following further development into three graphene-based materials (GBMs): Porous graphene adsorbent (PGa), Graphene-oxide foam adsorbent (GOFa), and the hybrid filter. Due to the nuances of each synthesis process, financial costs will differ throughout the GBMs’ life cycle which have been quantified and compared in the present work at a range of possible breakthrough times. Finally, economic and environmental costs have been combined for each technology to compare eco-efficiency. Results demonstrated a substantial economic advantage of the GBMs when compared to alternative technologies, most notably the GOFa filter that incurred the lowest life-cycle costs at $1.73 ± 0.09/m3. This was mainly attributed to the lower demand of GOFa on the most expensive material required for material synthesis, hydrazine. In addition, the material demands of GOFa were more evenly distributed which suggest a higher resilience of the overall costs to price hikes of individual materials required for synthesis. In terms of eco-efficiency the GOFa filter also demonstrated the greatest improvement when compared to the reference technology These results have provided robust total investment costs for several technologies that can now offer contrast to other EC-removal solutions.

Adsorption and reduction from modified polypyrrole enhance electrokinetic remediation of hexavalent chromium-contaminated soil

Toxic metal pollutant Cr(VI) in the environment will pose a severe threat to animal and human health. In this work, Fe₃O₄@PPy, Arg@PPy, and Arg/Fe₃O₄@PPy were prepared to enhance adsorption of Cr(VI) by doping Fe₃O₄ nanoparticles and amino radicals into the original PPy structure. Their characteristics were investigated by FTIR, SEM, EDS, BET analysis, and batch adsorption experiments. And they were used as permeable reaction barriers (PRB) to combine with electrokinetic remediation (EKR) to remediate Cr-contaminated soil. Adsorption experiment results showed that the maximum adsorption capacities of PPy, Fe₃O₄@PPy, Arg@PPy, and Arg/Fe₃O₄@PPy for Cr(VI) were 60.43 mg/g, 67.12 mg/g, 159.86 mg/g, and 141.50 mg/g, respectively. They all followed the kinetic pseudo-second-order model and the Langmuir isothermal model with a monolayer adsorption behavior. In the EKR/PRB system, the presence of Fe₃O₄@PPy, Arg@PPy, and Arg/Fe₃O₄@PPy obtained the higher Cr(VI) removal efficiency near the anode than that of the PPy, increasing by 74.60%, 26.04%, and 68.64%, respectively. A strong electrostatic attraction between anion contaminants and protonated modified PPy and a reduction from Cr(VI) to Cr(III) appeared in the EKR remediation process under acid conditions. This study opened up a prospect for applying modified PPy composites to treat toxic metal-contaminated soil.

A novel electrokinetic remediation with in-situ generation of H2O2 for soil PAHs removal

Electrokinetic-Fenton (EK-Fenton) technology requires a high dose of H₂O₂ to produce •OH radicals, which adds a high cost to the remediation process and raises safety concerns during transportation and storage of H₂O₂. Moreover, the remediation efficiency of the conventional EK-Fenton process is low due to the meaningless consumption of H₂O₂ on the electrodes and the alkaline environment near the cathode. In this work, a modified CMK3-gas diffusion electrode (CMK3-GDE) is fabricated. This cathode can continuously generate H₂O₂, and the cumulative H₂O₂ concentration can reach 0.23 M during 10 days of the test. The utilization of cation exchange membranes (CEMs) efficiently restricts the decomposition of H₂O₂ on the electrodes and prevents the alkalization of the soil near the cathode, resulting in a 13.7-43.2% increase of the removal efficiency of polycyclic aromatic hydrocarbons (PAHs). In this new treatment process, PAHs are mainly oxidized into quinones, ketones, alcohols, and small molecule acids, and all these products have lower toxicities than PAHs. The EK-Fenton/CMK3-GDE-CEM system exhibits excellent remediation efficiency for treating PAHs polluted soil, which could be a sustainable, eco-friendly, and low-cost strategy for soil remediation.

Migration and Removal of Labile Cadmium Contaminants in Paddy Soils by Electrokinetic Remediation without Changing Soil pH

Electrokinetic remediation (EKR) is a viable, advanced cleaning strategy that can permanently reduce the toxicity of soil contaminants. However, EKR is prone to causing changes in soil pH. The negative impacts must be minimized if field-scale application is to be realized. In this study, EKR with polarity reversal was used to avoid soil pH polarization and to clean up cadmium (Cd)-contaminated paddy soils. Results showed that Cd desorbed from oxidizable and residual fractions to labile and easily available parts. Soil moisture content above 0.35 g g⁻¹ was conductive to achieving the desirable Cd-migration rate. The exchangeable Cd phase eventually migrated from both ends of that soil compartment towards the intermediate. Moreover, the addition of citric acid at the concentration of 0.1 mol L⁻¹ was an effective enhancement strategy. The methodology enriched Cd contaminants to specific sites. The technology can be used for electrokinetic-assisted phytoremediation during the rice growing period. Hyperaccumulator is planted in the intermediate area to remove the Cd contaminants. On the other hand, Cd removal is achieved in the region close to the electrodes. The present study provides a theoretical basis for in situ remediation. It has a wider significance for field-scale application.

Enhanced remediation of Cd-contaminated soil using electrokinetic assisted by permeable reactive barrier with lanthanum-based biochar composite filling materials

Electrokinetic remediation (EK) combined with a permeable reactive barrier (PRB) is a relatively new technique for efficiently remediating Cd-contaminated soil in situ. Eupatorium adenophorum, which is a malignant invasive plant, was used to synthesise biochar and a novel lanthanum-based biochar composite (LaC). The biochar and LaC were used as cheap and environmentally benign PRB filling materials to remediate simulated and real Cd-contaminated soils. The pH and residual Cd concentration in the simulated contaminated soil during remediation gradually increased from the anode to the cathode used to apply an electric field to the EK-PRB system. However, the soil conductivity changed in the opposite way, and the current density first increased and then decreased. For simulated contaminated soils with initial Cd concentrations of 34.9 and 100.6 mg kg^-1, the mean Cd removal rates achieved using LaC were 90.6% and 89.3%, respectively, which were significantly higher than those of biochar (P < 0.05). Similar results were achieved using natural soils from mining area and polluted farmland, and the Cd removal rates were 66.9% and 72.0%, respectively. Fourier-transform infrared and X-ray photoelectron spectroscopy indicated that there were many functional groups on the LaC surfaces. The removal mechanism of EK-PRB for Cd in contaminated soil includes electromigration, electroosmotic flow, surface adsorption, and ion exchange. The results indicated that the LaC could be used in the EK-PRB technique as a cheap and 'green' material to efficiently decontaminate soil polluted with heavy metals.

Froth-Flotation Separation as an Alternative for the Treatment of Soil Enriched with Fluorine Derived from Mica

Fluorine (F) enrichment originating from natural sources is difficult to remove using chemical washing methods due to the large chemical-resistant residual fraction. This study evaluates the feasibility of using a froth-flotation separation method to remediate soil with a high F concentration caused by mica weathering, and it investigates the optimal conditions for this process, including pH of the slurry, collector dosage, and sample mechanical preparation strategy. The established optimum conditions are pH 3.5, 300 mg/kg collector dosage (tallow amine acetate), which can effectively separate quartz and mica, and a sieving-and-milling strategy that involves discarding particles of size < 0.05 mm, milling those in the range of 0.5-2.0 mm (until < approx. 0.3 mm), and mixing particles with sizes in the range of 0.05-0.5 mm. The target contamination level of 400 mg/kg for the test soil was not met after the first flotation separation process. However, after milling the residue of the first process and subjecting it to a second flotation separation process, the required contamination level was achieved. Consequently, the proposed froth-flotation separation process can be used as a successful alternative technique to remediate F-enriched soils from natural origin that have highly chemical-resistant forms.

In-situ, Ex-situ, and nano-remediation strategies to treat polluted soil, water, and air - A review

Nanotechnology, as an emerging science, has taken over all fields of life including industries, health and medicine, environmental issues, agriculture, biotechnology etc. The use of nanostructure molecules has revolutionized all sectors. Environmental pollution is a great concern now a days, in all industrial and developing as well as some developed countries. A number of remedies are in practice to overcome this problem. The application of nanotechnology in the bioremediation of environmental pollutants is a step towards revolution. The use of various types of nanoparticles (TiO₂ based NPs, dendrimers, Fe based NPs, Silica and carbon nanomaterials, Graphene based NPs, nanotubes, polymers, micelles, nanomembranes etc.) is in practice to diminish environmental hazards. For this many In-situ (bioventing, bioslurping, biosparging, phytoremediation, permeable reactive barrier etc.) and Ex-situ (biopile, windrows, bioreactors, land farming etc.) methodologies are employed. Improved properties like nanoscale size, less time utilization, high adaptability for In-situ and Ex-situ use, undeniable degree of surface-region to-volume proportion for possible reactivity, and protection from ecological elements make nanoparticles ideal for natural applications. There are distinctive nanomaterials and nanotools accessible to treat the pollutants. Each of these methods and nanotools depends on the properties of foreign substances and the pollution site. The current designed review highlights the techniques used for bioremediation of environmental pollutants as well as use of various nanoparticles along with proposed In-situ and Ex-situ bioremediation techniques.

An overview of in-situ remediation for nitrate in groundwater

Faced with the increasing nitrate pollution in groundwater, in-situ remediation has been widely studied and applied on field-scale as an efficient, economical and less disturbing remediation technology. In this review, we discussed various in-situ remediation for nitrate in groundwater and elaborate on biostimulation, phytoremediation, electrokinetic remediation, permeable reactive barrier and combined remediation. This review described principles of each in-situ remediation, application, the latest progress, problems and challenges on field-scale. Factors affecting the efficiency of in-situ remediation for nitrate in groundwater are also summarized. Finally, this review presented the prospect of in-situ remediation for nitrate pollution in groundwater. The objective of this review is to examine the state of knowledge on in-situ remediation for nitrate in groundwater and critically evaluate factors which affect the up-scaling of laboratory and bench-scale research to field-scale application. This helps to better understand the control mechanisms of various in-situ remediation for nitrate pollution in groundwater and the design options available for application to the field-scale.

Nanomaterials for Remediation of Environmental Pollutants

Today, environmental contamination is a big concern for both developing and developed countries. The primary sources of contamination of land, water, and air are extensive industrialization and intense agricultural activities. Various traditional methods are available for the treatment of different pollutants in the environment, but all have some limitations. Due to this, an alternative method is required which is effective and less toxic and provides better outcomes. Nanomaterials have attracted a lot of interest in terms of environmental remediation. Because of their huge surface area and related high reactivity, nanomaterials perform better in environmental clean-up than other conventional approaches. They can be modified for specific uses to provide novel features. Due to the large surface-area-to-volume ratio and the presence of a larger number of reactive sites, nanoscale materials can be extremely reactive. These characteristics allow for higher interaction with contaminants, leading to a quick reduction of contaminant concentration. In the present review, an overview of different nanomaterials that are potential in the remediation of environmental pollutants has been discussed.

Enhanced remediation of heavy metals contaminated soils with EK-PRB using β-CD/hydrothermal biochar by waste cotton as reactive barrier

Heavy metals in the soil are major global environmental problems. Waste cotton was used to synthesize a novel β-CD/hydrothermal biochar (KCB), which is a low-cost and environment-friendly adsorbent for heavy metal soil remediation. KCB were used as reactive materials of electrokinetic-permeable reactive barrier (EK-PRB) to explore the removal characteristics of heavy metals. FTIR and XPS analysis revealed that KCB contained large numbers of surface functional groups. Adsorption of KCB for Pb²⁺ and Cd²⁺ reached 50.44 mg g^-1 and 33.77 mg g^-1, respectively. Metal ions in contaminated soil were removed by reactive barrier through electromigration, electrodialysis and electrophoresis, the removal efficiency of Pb²⁺ and Cd²⁺ in soil reached 92.87% and 86.19%. This finding proves that KCB/EK-PRB can be used as a cheap and green process to effectively remediate soils contaminated with heavy metals.