Conductive polymers in water treatment: A review

Investigation of Doehlert matrix conception in novel intrinsically conducting polymers based on selenium nanoparticles for wastewater treatment: Synthesis, characterization, kinetic and chemometric study

The synthesis of robust intrinsically conducting polymers (ICPs) based on nanoparticles is becoming increasingly attractive to the research community due to the unique properties of these nanocomposites. Indeed, as organic semiconductors, ICPs combine both polymer and metal properties in a single structure. This study presents an innovative approach in which the Doehlert Matrix (DM) is applied to a novel ICP nanocomposite based on polyaniline (Pani) coupled with selenium (Se) loaded mesoporous titania (TiO2) for wastewater treatment by photocatalysis. It includes both the elaboration routes of ICP nanocomposites, characterization of materials by X-ray diffraction (XRD), BET analysis, thermogravimetric analysis (TGA), RAMAN spectroscopy and Fourier transform infrared spectroscopy (FTIR) and photodegradation of methylene blue (MB) as a representative of dye pollutant. In addition, the photocatalytic process has been optimized by a novel DM conception. The effect of the pH of the solution, the catalyst dosage and the initial pollutant concentration was investigated. The optimum conditions were found to be: initial MB concentration of 15 mg/L, the catalyst dosage of 69 mg and pH of 9.6 with an operating time of 75 min, with a coefficient of determination R2 equal to 0.9985. The removal efficiency of BM was close to 97 %. The study shows that the new ICP nanocomposites improve the photocatalytic efficiency compared to pure titania and/or pure Pani. In addition, as the ternary Pani-Se-TiO2 nanocomposite could be obtained from a low-cost synthesis, it is a very promising material for use in wastewater treatment.

Aerogels of Polypyrrole/Tannic Acid with Nanofibrillated Cellulose for the Removal of Hexavalent Chromium Ions

The preparation of conducting polymer aerogels is an effective strategy to produce innovative materials with enhanced physicochemical properties. Herein, polypyrrole (PPy) aerogels were oxidatively prepared in the presence of tannic acid (TA) with different concentrations (2.5, 5, and 10% mole ratio to pyrrole monomer) under freezing conditions. Nanofibrillated cellulose (NFC) was added during the PPy/TA synthesis to enhance mechanical stability. The effect of TA concentration on the aerogels' morphology, conductivity, thermal stability, and adsorption capacity was investigated. The conductivity of 9.6 ± 1.7 S cm-1 was achieved for PPy/TA prepared with 2.5% TA, which decreased to 0.07 ± 0.01 S cm-1 when 10% TA was used. PPy/TA aerogels have shown high efficacy in removing Cr(VI) ions from aqueous solutions. Adsorption experiments revealed that all the aerogels follow pseudo-second-order kinetics. PPy/TA prepared with NFC has a maximum adsorption capacity of 549.5 mg g-1.

Insight into soft chemometric computational learning for modelling oily-wastewater separation efficiency and permeate flux of polypyrrole-decorated ceramic-polymeric membranes

Reliable modeling of oily wastewater emphasizes the paramount importance of sustainable and health-conscious wastewater management practices, which directly aligns with the Sustainable Development Goals (SDG) while also meeting the guidelines of the World Health Organization (WHO). This research explores the efficiency of utilizing polypyrrole-coated ceramic-polymeric membranes to model oily wastewater separation efficiency (SE) and permeate flux (PF) based on established experimental procedures. In this area, computational simulation still needs to be explored. The study developed predictive regression models, including robust linear regression (RLR), stepwise linear regression (SWR) and linear regression (LR) for the ceramic-polymeric porous membrane, aiming to interpret its complex performance across diverse conditions and, thus, develop its utility in oily wastewater treatment applications. Subsequently, a novel, simple average ensemble paradigm was explored to reduce errors and improve prediction skills. Prior to the development of the model, stability and reliability analysis of the data was conducted based on Philip Perron tests with the Bartlett kernel estimation method. The accuracy of the SE exhibited a high consistency, averaging 99.92% with minimal variability (standard deviation of 0.026%), potentially simplifying its prediction compared to PF. The modes were validated and evaluated using metrics like MAE, RMSE, Speed, and MSE, in addition to 2D graphical and cumulative distribution function graphs. The LR model emerged as the best with the lowest RMSE =0.21951, indicating superior prediction accuracy, followed closely by RLR with an RMSE = 0.22359. SWLR, while having the highest RMSE = 0.34573, marked its dominance in prediction speed with 110 observations per second. Notably, the RLR model justified a reduction in error by approximately 35.29% compared to SWLR. Moreover, the training efficiency of the LR model exceeded, demanding a mere 2.9252 s, marking a reduction of about 32.54% compared to SWLR. The improved simple ensemble learning proved merit over the three models regarding error accuracy. This study emphasizes the essential role of soft-computing learning in optimizing the design and performance of ceramic-polymeric membranes.

A Review of Conductive Hydrogel-Based Wearable Temperature Sensors

Conductive hydrogel has garnered significant attention as an emergent candidate for diverse wearable sensors, owing to its remarkable and tailorable properties such as flexibility, biocompatibility, and strong electrical conductivity. These attributes make it highly suitable for various wearable sensor applications (e.g., biophysical, bioelectrical, and biochemical sensors) that can monitor human health conditions and provide timely interventions. Among these applications, conductive hydrogel-based wearable temperature sensors are especially important for healthcare and disease surveillance. This review aims to provide a comprehensive overview of conductive hydrogel-based wearable temperature sensors. First, this work summarizes different types of conductive fillers-based hydrogel, highlighting their recent developments and advantages as wearable temperature sensors. Next, this work discusses the sensing characteristics of conductive hydrogel-based wearable temperature sensors, focusing on sensitivity, dynamic stability, stretchability, and signal output. Then, state-of-the-art applications are introduced, ranging from body temperature detection and wound temperature detection to disease monitoring. Finally, this work identifies the remaining challenges and prospects facing this field. By addressing these challenges with potential solutions, this review hopes to shed some light on future research and innovations in this promising field.

Preparation and characterization of CS/PAT/ MWCNT@MgAl-LDHs nanocomposite for Cd2+ removal and 4-nitrophenol reduction

The present study evaluated the performance of multiwalled carbon nanotube (MWCNT)@MgAl-layered double hydroxide (LDH) nanoparticles loaded on poly-2 aminothiazole (PAT)/chitosan (CS) matrix (CPML) to remove Cd2+ ions from aqueous solution. The removal efficiency of modified CS/PAT with MWCNT@MgAl-LDHs was increased significantly compared to pure CS/PAT. The influence of heavy metal ion concentration, pH, temperature, adsorbent dosage, and contact time on the adsorption was examined. The optimum conditions for the adsorption of Cd2+ ions were 25 0C with the adsorbent dosage of 0.06 g and initial concentration for adsorption of the Cd2+ 100 mg/L at pH = 8. The maximum adsorption capacity was measured to be 1106.19 mg/g. The values of thermodynamic parameters namely Gibbs free energy (ΔG°), entropy change (ΔS°), and enthalpy change (ΔH°) indicated the feasibility, spontaneity and the endothermic nature of the adsorption process, respectively. The pseudo-second-order kinetics and the Langmuir model were selected as the best models for the adsorption process. Also, CPML nanocomposite (NC) was successfully tested for p-nitrophenol (p-NP) reduction in the presence of NaBH4. The reaction was nearly completed in 6 min. The fabricated CPML-NC could be reused for three consecutive cycles.

Removal of Anionic Methyl Orange Dye from Water by Poly[2-methyl-1H-indole] Derivatives: Investigation of Kinetics and Isotherms of Adsorption

The adsorption properties toward methyl orange (MO) were evaluated for poly[2-methyl-1H-indole] and its derivatives. The influence of pH, ionic strength of solution, composition, and amount of sorbent on the adsorption of MO dye was investigated; the kinetics of dye adsorption was studied. The adsorption isotherms were analyzed using different models of sorption equilibrium. The presence of chemical interaction between polyindoles and dye was proved by IR and UV spectroscopy methods. The sorption of MO with polymers is realized mainly due to the formation of electrostatic interactions between the sulfogroup of the dye and the imino group of the sorbent. Microphotographs demonstrate the change in the morphology of polyindoles after adsorption, which further confirms the structural changes in the polymers. It was found that the main factors affecting the sorption capacity of the studied materials are the position and nature of substituents in the polymers and the sorption conditions. For example, polyindoles containing a methoxy group in their structure (o-OMePIn and m-OMePIn) have the best sorption activity. These polymers are effective in adsorbing dyes, which means that they can be used in wastewater treatment.

Efficient purification of low-level uranium-containing wastewater by polyamine/amidoxime synergistically reinforced fiber

The removal and recovery of uranium [U(VI)] from organic containing wastewater has been a challenging in radioactive wastewater purification. Here, we designed a polyamine/amidoxime polyacrylonitrile fiber (PAN-AO-A) with high removal efficiency, excellent selectivity, excellent organic resistance and low cost by combining the anti-organic properties of amidoxime polyacrylonitrile fiber (PAN-AO-A) with the high adsorption capacity of polyamine polyacrylonitrile fiber, which is used to extract U(VI) from low-level uranium-containing wastewater with high ammonia nitrogen and organic content. PAN-AO-A adsorbent with high grafting rate (86.52%), high adsorption capacity (qe = 618.8 mg g-1), and strong resistance to organics and impurity interference is achieved. The adsorption rate of U(VI) in both real organic and laundry wastewater containing uranium is as high as 99.7%, and the partition coefficients (Kd) are 7.61 × 105 mL g-1 and 9.16 × 106 mL g-1, respectively. The saturated adsorption capacity of PAN-AO-A in the continuous system solution can reach up to 505.5 mg g-1, and the concentration of U(VI) in the effluent is as low as 1 μg L-1. XPS analysis and Density functional theory (DFT) studies the coordination form between U(VI) and PAN-AO-A, where the most stable structure is η2-AO(UO2)(CO3)2. The -NH-/-NH2 and -C(NH2)N-OH groups of PAN-AO-A exhibit a synergistic complex effect in the U(VI) adsorption process. PAN-AO-A is a material with profound influence and limitless potential that can be used for wastewater containing U(VI) and organic matter.

Selective Adsorption Behavior of Sulfuric Acid Oxidized and Doped Conjugated Microporous Poly(aniline)s toward Lead Ions in an Aqueous Environment

The coexistence of lead, zinc, and copper ions in wastewater constitutes an environmental challenge of pressing concern. This research delves into the preparation of innovative oxidation-doped conjugated microporous poly(aniline) frameworks, exploring their prospective efficacy in regulating lead ion adsorption from aqueous solutions. H2SO4-CMPTA demonstrates the capability to reach adsorption equilibrium within 15 min at a lead concentration of 50 ppm. Even at a lead concentration of 20 ppm, it still efficaciously attenuates these levels to sub-10 ppb, a value surpassing extant standard. H2SO4-CMPTA retains over 78.8% adsorption efficiency after six cycles. Analytical characterization coupled with computational calculations suggests that sulfate-coordinated nitrogen cationic structure plays a crucial role in adsorption. A deeper investigation reveals the cardinal role of electrostatic attraction and exclusive chelation adsorption underpinning the efficient capture of lead ions by doped sulfate ions. Intriguingly, in a mixed heavy metal solution containing lead, zinc, and copper ions, H2SO4-CMPTA exhibits an initial predilection toward zinc ions, yet an eventual ion-exchange adsorption gravitating toward lead ions was discerned, governed by the latter's superior binding energy. Our study elucidates a promising material as an efficacious tool for the remediation of aquatic environments tainted with lead contaminants.

Removal of emergent pollutants: A review on recent updates and future perspectives on polysaccharide-based composites vis-à-vis traditional adsorbents

There is a growing incidence in the presence of emergent pollutants like the pesticides and pharmaceuticals in water bodies. The matter of environmental concern is their synthetic and persistent nature which has resulted in induced toxicity/damaging effect to the vital functioning of the different organs in the aquatic community. Traditional adsorbents have exhibited limitations like low stability and minimum reuse ability. Composites of such adsorbents with polysaccharides have demonstrated distinct features like improved surface area, porosity, adsorptivity; improved reusability and structural integrity; improved mechanical strength, thermal stability when applied for the removal of the emergent pollutants. The biocompatibility and biodegradability of such fabricated composites is established; thereby making the water treatment process cost effective, sustainable and environmentally friendly. The present review has dealt with an in-depth, up-dated literature compilation of traditional as well as polysaccharide based composite adsorbents and addressed their performance evaluation for the removal of pharmaceuticals and pesticides from wastewater. A comparative study has revealed the merits of polysaccharide based composites and discussions have been made with a focus on future research directions in the related area.

Polysaccharide nanocomposites in wastewater treatment: A review

In modern times, wastewater treatment is vital due to increased water contamination arising from pollutants such as nutrients, pathogens, heavy metals, and pharmaceutical residues. Polysaccharides (PSAs) are natural, renewable, and non-toxic biopolymers used in wastewater treatment in the field of gas separation, liquid filtration, adsorption processes, pervaporation, and proton exchange membranes. Since addition of nanoparticles to PSAs improves their sustainability and strength, nanocomposite PSAs has gained significant attention for wastewater treatment in the past decade. This review presents a comprehensive analysis of PSA-based nanocomposites used for efficient wastewater treatment, focusing on adsorption, photocatalysis, and membrane-based methods. It also discusses potential future applications, challenges, and opportunities in adsorption, filtration, and photocatalysis. Recently, PSAs have shown promise as adsorbents in biological-based systems, effectively removing heavy metals that could hinder microbial activity. Cellulose-mediated adsorbents have successfully removed various pollutants from wastewater, including heavy metals, dyes, oil, organic solvents, pesticides, and pharmaceutical residues. Thus, PSA nanocomposites would support biological processes in wastewater treatment plants. A major concern is the discharge of antibiotic wastes from pharmaceutical industries, posing significant environmental and health risks. PSA-mediated bio-adsorbents, like clay polymeric nanocomposite hydrogel beads, efficiently remove antibiotics from wastewater, ensuring water quality and ecosystem balance. The successful use of PSA-mediated bio-adsorbents in wastewater treatment depends on ongoing research to optimize their application and evaluate their potential environmental impacts. Implementing these eco-friendly adsorbents on a large scale holds great promise in significantly reducing water pollution, safeguarding ecosystems, and protecting human health.

Nanoparticles and nanofiltration for wastewater treatment: From polluted to fresh water

Water pollution poses significant threats to both ecosystems and human health. Mitigating this issue requires effective treatment of domestic wastewater to convert waste into bio-fertilizers and gas. Neglecting liquid waste treatment carries severe consequences for health and the environment. This review focuses on intelligent technologies for water and wastewater treatment, targeting waterborne diseases. It covers pollution prevention and purification methods, including hydrotherapy, membrane filtration, mechanical filters, reverse osmosis, ion exchange, and copper-zinc cleaning. The article also highlights domestic purification, field techniques, heavy metal removal, and emerging technologies like nanochips, graphene, nanofiltration, atmospheric water generation, and wastewater treatment plants (WWTPs)-based cleaning. Emphasizing water cleaning's significance for ecosystem protection and human health, the review discusses pollution challenges and explores the integration of wastewater treatment, coagulant processes, and nanoparticle utilization in management. It advocates collaborative efforts and innovative research for freshwater preservation and pollution mitigation. Innovative biological systems, combined with filtration, disinfection, and membranes, can elevate recovery rates by up to 90%, surpassing individual primary (<10%) or biological methods (≤50%). Advanced treatment methods can achieve up to 95% water recovery, exceeding UN goals for clean water and sanitation (Goal 6). This progress aligns with climate action objectives and safeguards vital water-rich habitats (Goal 13). The future holds promise with advanced purification techniques enhancing water quality and availability, underscoring the need for responsible water conservation and management for a sustainable future.

Ionic transport through a bilayer nanoporous graphene with cationic and anionic functionalization

Understanding the ionic transport through multilayer nanoporous graphene (NPG) holds great promise for the design of novel nanofluidic devices. Bilayer NPG with different structures, such as nanopore offset and interlayer space, should be the most simple but representative multilayer NPG. In this work, we use molecular dynamics simulations to systematically investigate the ionic transport through a functionalized bilayer NPG, focusing on the effect of pore functionalization, offset, applied pressure and interlayer distance. For a small interlayer space, the fluxes of water and ions exhibit a sudden reduction to zero with the increase in offset that indicates an excellent on-off gate, which can be deciphered by the increasing potential of mean force barriers. With the increase in pressure, the fluxes increase almost linearly for small offsets while always maintain zero for large offsets. Finally, with the increase in interlayer distance, the fluxes increase drastically, resulting in the reduction in ion rejection. Notably, for a specific interlayer distance with monolayer water structure, the ion rejection maintains high levels (almost 100% for coions) with considerable water flux, which could be the best choice for desalination purpose. The dynamics of water and ions also exhibit an obvious bifurcation for cationic and anionic functionalization. Our work comprehensively addresses the ionic transport through a bilayer NPG and provides a route toward the design of novel desalination devices.

Multifaceted synergistic facilitation mechanism of conductive polymers in promoting selenite bioreduction and biological detoxification

Here, polypyrrole (PPY) was first used to the bioreduction of toxic selenite, while the acceleration effect and mechanism were explored. Experiment results suggested that PPY could enhance the selenite bioreduction from 0.42 to 1.04 mg/(L·h). The tests of electrochemical analysis and cytochrome c (cyt-c) content confirmed that PPY promoted the intracellular/intracellular electron transfer of Shewanella oneidensis·MR-1 in selenite bioreduction process. The enhancement of metabolic activity by PPY contributed to biological detoxification, which was manifested in the increased extracellular polymeric substances (EPS), adenosine triphosphate (ATP), electron transfer system activity (ETSA), membrane permeability and enzyme activity. Transcriptome analysis of DEGs, KEGG pathway enrichment and GO functional classification verified that the environmental adaptability of Shewanella oneidensis·MR-1 was enhanced with the addition of PPY. The transmission electron microscopy (TEM) images indicated that PPY promoted the biosynthesis of selenium nanoparticles (SeNPs), which was beneficial to reduce cell damage. Combined with the above results, a multifaceted synergistic facilitation mechanism based on "conductive cross-linking network" was elaborated from electron transfer, microbial metabolism and environmental adaptability. This study shed light the effect of conductive polymers (CPs) on selenite bioreduction and provided new insights into the bioremediation of toxic pollutants.

Polyaniline-silica doped with oxalic acid as a novel extractor phase in thin film solid-phase microextraction for determination of hormones in urine

In this study, different polyanilines were synthesized and evaluated for the determination of three hormones, including 17-β-estradiol, 17-α-ethinylestradiol, and estrone, in urine using a novel methodology based on thin film solid-phase microextraction technique, employing the sampling well plate system. The extractor phases, designated as polyaniline doped with hydrochloric acid, polyaniline doped with oxalic acid, polyaniline-silica doped with hydrochloric acid, and polyaniline-silica doped with oxalic acid, were characterized by electrical conductivity measurements, scanning electron microscopy, and Fourier transform infrared spectroscopy. The optimized extraction conditions were composed of 1.5 mL of urine and pH adjusted to 10, with no need to dilute sample and the desorption step, 300 μL of acetonitrile was used. The calibration curves were performed in the sample matrix, with detection and quantification limits ranged from 0.30 to 3.03 μg L-1 and from 1.0 to 10.0 μg L-1 , respectively, with r ≥ 0.9969. The relative recoveries ranged from 71% to 115%, and intraday precision showed values ≤12% and interday ≤20%. The applicability of the method was successfully evaluated, and six urine samples from female volunteers were analyzed. The analytes were not detected or were below the limits of quantification in these samples.

One-Step Accelerated Synthesis of Conducting Polymer/Silver Composites and Their Catalytic Reduction of Cr(VI) Ions and p-Nitrophenol

In this paper, silver nitrate was used as an oxidant to prepare polyaniline, polypyrrole, and poly(3,4-ethylene dioxythiophene)/silver composites through a simultaneous oxidation/reduction process. In addition, p-phenylenediamine was added with 1 mole% relative to the concentrations of the monomers to accelerate the polymerization reaction. The prepared conducting polymer/silver composites were characterized by scanning and transmission electron microscopies to study their morphologies; Fourier-transform infrared and Raman spectroscopies to confirm their molecular structures; and thermogravimetric analysis (TGA) to study their thermal stabilities. The silver content in the composites was estimated by energy-dispersive X-ray spectroscopy, ash analysis, and TGA. The conducting polymer/silver composites were utilized for the remediation of water pollutants through catalytic reduction. Hexavalent chromium ions (Cr(VI)) were photocatalytically reduced to trivalent chromium ions, and p-nitrophenol was catalytically reduced to p-aminophenol. The catalytic reduction reactions were found to follow the first-order kinetic model. Among the prepared composites, polyaniline/silver composite has shown the highest activity for the photocatalytic reduction of Cr(VI) ions with an apparent rate constant of 0.226 min^-1 and efficiency of 100% within 20 min. Additionally, poly(3,4-ethylene dioxythiophene)/silver composite showed the highest catalytic activity towards the reduction of p-nitrophenol with an apparent rate constant of 0.445 min^-1 and efficiency of 99.8% within 12 min.

Recent advances in conducting polymer-based magnetic nanosorbents for dyes and heavy metal removal: fabrication, applications, and perspective

Globally, treating and disposing of industrial pollutants is a techno-economic challenge. Industries' large production of harmful heavy metal ions (HMIs) and dyes and inappropriate disposal worsen water contamination. Much attention is required on the development of efficient and cost-effective technologies and approaches for removing toxic HMIs and dyes from wastewater as they pose a severe threat to public health and aquatic ecosystems. Due to the proven superiority of adsorption over other alternative methods, various nanosorbents have been developed for the efficient removal of HMIs and dyes from wastewater and aqueous solutions. Being a good adsorbent, conducting polymer-based magnetic nanocomposites (CP-MNCPs) has drawn more attention for HMIs and dye removal. Conductive polymers' pH-responsiveness makes CP-MNCP ideal for wastewater treatment. The composite material absorbed dyes and/or HMIs from contaminated water could be removed by changing the pH. Here, we review the production strategies and applications of CP-MNCPs for HMIs and dye removal. The review also sheds light on the adsorption mechanism, adsorption efficiency, kinetic and adsorption models, and regeneration capacity of the various CP-MNCPs. To date, various modifications to conducting polymers (CPs) have been explored to improve the adsorption properties. It is evident from the literature survey that the combination of SiO₂, graphene oxide (GO), and multi-walled carbon nanotubes (MWCNTs) with CPs-MNCPs enhances the adsorption capacity of nanocomposites to a large extent, so future research should lean toward the development of cost-effective hybrid CPs-nanocomposites.

Cellulose: A Review of Water Interactions, Applications in Composites, and Water Treatment

Cellulose is known to interact well with water, but is insoluble in it. Many polysaccharides such as cellulose are known to have significant hydrogen bond networks joining the molecular chains, and yet they are recalcitrant to aqueous solvents. This review charts the interaction of cellulose with water but with emphasis on the formation of both natural and synthetic fiber composites. Covering studies concerning the interaction of water with wood, the biosynthesis of cellulose in the cell wall, to its dispersion in aqueous suspensions and ultimately in water filtration and fiber-based composite materials this review explores water-cellulose interactions and how they can be exploited for synthetic and natural composites. The suggestion that cellulose is amphiphilic is critically reviewed, with relevance to its processing. Building on this, progress made in using various charged and modified forms of nanocellulose to stabilize oil-water emulsions is addressed. The role of water in the aqueous formation of chiral nematic liquid crystals, and subsequently when dried into composite films is covered. The review will also address the use of cellulose as an aid to water filtration as one area where interactions can be used effectively to prosper human life.

Polymer-Based Conductive Nanocomposites for the Development of Bioanodes Using Membrane-Bound Enzyme Systems of Bacteria Gluconobacter oxydans in Biofuel Cells

The development of biofuel cells (BFCs) currently has high potential since these devices can be used as alternative energy sources. This work studies promising materials for biomaterial immobilization in bioelectrochemical devices based on a comparative analysis of the energy characteristics (generated potential, internal resistance, power) of biofuel cells. Bioanodes are formed by the immobilization of membrane-bound enzyme systems of Gluconobacter oxydans VKM V-1280 bacteria containing pyrroloquinolinquinone-dependent dehydrogenases into hydrogels of polymer-based composites with carbon nanotubes. Natural and synthetic polymers are used as matrices, and multi-walled carbon nanotubes oxidized in hydrogen peroxide vapor (MWCNTox) are used as fillers. The intensity ratio of two characteristic peaks associated with the presence of atoms C in the sp³ and sp² hybridization for the pristine and oxidized materials is 0.933 and 0.766, respectively. This proves a reduced degree of MWCNTox defectiveness compared to the pristine nanotubes. MWCNTox in the bioanode composites significantly improve the energy characteristics of the BFCs. Chitosan hydrogel in composition with MWCNTox is the most promising material for biocatalyst immobilization for the development of bioelectrochemical systems. The maximum power density was 1.39 × 10^-5 W/mm², which is 2 times higher than the power of BFCs based on other polymer nanocomposites.

Polypyrrole-Barium Ferrite Magnetic Cryogels for Water Purification

Magnetic polypyrrole-gelatin-barium ferrite (PPy-G-BaFe) cryogels/aerogels were synthesized by one-step oxidative cryopolymerization of pyrrole in the presence of various fractions of barium ferrite (BaFe) nanoparticles, dispersed in aqueous gelatin solution. The successful incorporation of BaFe into the composites was confirmed by elemental analysis and scanning electron microscopy paired with an energy-dispersive X-ray detector. The maximum achieved content of BaFe in the resulting material was 3.9 wt%. The aerogels with incorporated BaFe had significantly higher specific surface area and conductivity, reaching 19.3 m² g^-1 and 4 × 10^-4 S cm^-1, respectively, compared to PPy-G aerogel, prepared in the absence of BaFe (7.3 m² g^-1 and 1 × 10^-5 S cm^-1). The model adsorption experiment using an anionic dye, Reactive Black 5, showed that magnetic PPy-G-BaFe aerogel, prepared at 10 wt% BaFe fraction, had significantly higher adsorption rate and higher adsorption capacity, compared to PPy-G (dye removal fraction 99.6% and 89.1%, respectively, after 23 h). Therefore, the prepared PPy-G-BaFe aerogels are attractive adsorbents for water purification due to their enhanced adsorption performance and the possibility of facilitated separation from solution by a magnetic field.

Electrically conductive carbon-based (bio)-nanomaterials for cardiac tissue engineering

A proper self-regenerating capability is lacking in human cardiac tissue which along with the alarming rate of deaths associated with cardiovascular disorders makes tissue engineering critical. Novel approaches are now being investigated in order to speedily overcome the challenges in this path. Tissue engineering has been revolutionized by the advent of nanomaterials, and later by the application of carbon-based nanomaterials because of their exceptional variable functionality, conductivity, and mechanical properties. Electrically conductive biomaterials used as cell bearers provide the tissue with an appropriate microenvironment for the specific seeded cells as substrates for the sake of protecting cells in biological media against attacking mechanisms. Nevertheless, their advantages and shortcoming in view of cellular behavior, toxicity, and targeted delivery depend on the tissue in which they are implanted or being used as a scaffold. This review seeks to address, summarize, classify, conceptualize, and discuss the use of carbon-based nanoparticles in cardiac tissue engineering emphasizing their conductivity. We considered electrical conductivity as a key affecting the regeneration of cells. Correspondingly, we reviewed conductive polymers used in tissue engineering and specifically in cardiac repair as key biomaterials with high efficiency. We comprehensively classified and discussed the advantages of using conductive biomaterials in cardiac tissue engineering. An overall review of the open literature on electroactive substrates including carbon-based biomaterials over the last decade was provided, tabulated, and thoroughly discussed. The most commonly used conductive substrates comprising graphene, graphene oxide, carbon nanotubes, and carbon nanofibers in cardiac repair were studied.

Novel polyaniline-polyethersulfone nanofiltration membranes: effect of in situ polymerization time on structure and desalination performance

In this research, novel polyaniline-layered nanofiltration membranes were prepared by phase inversion of base polyethersulfone (PES) membranes and subsequent in situ solution-phase deposition of polyaniline as a thin surface layer. In these composite membranes, the impact of the polyaniline deposition time on steric hindrance and electrostatic interactions during permeation was elucidated. The chemical structure, thermal stability, and mechanical properties of the PES and PANI-PES membranes were investigated using Fourier-transform infrared spectroscopy (ATR-FTIR), thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA), respectively. The membranes' porosity and pore size decreased as PANI deposition time increased. As PANI deposition time increased, PANI layered nanofiltration membranes exhibited improved thermal stability but deteriorated mechanical characteristics due to free radical destruction from prolonged exposure to the oxidant. These PANI-PES membranes showed 43% rejection (NaCl) at 1.7 bar coupled with a flux of 11.59 L h^-1 m² that is quite promising when comparing with similar Nanofilteration (NF) membranes in the literature and commercial NF membranes, as well. As the deposited layer, PANI is partially doped; hence, permeation results have been interpreted in terms of steric hindrance and electrostatic repulsion by electrochemical PANI layering.

Revealing the mechanisms of polypyrrole (Ppy) enhancing methane production from anaerobic digestion of waste activated sludge (WAS)

Anaerobic digestion (AD) is a promising method for treating waste activated sludge (WAS), but the low methane yield limits its large-scale application. The addition of conductive nanomaterials has been demonstrated to enhance the activity of AD via promoting the direct interspecies electron transfer (DIET). In this study, novel conductive polypyrrole (Ppy) was prepared to effectively improve the AD performance of WAS. The results showed that the accumulative methane production was enhanced by 27.83% by Ppy, with both acidogenesis and methanogenesis being efficiently accelerated. The microbial community analysis indicated that the abundance of bacteria associated with acidogenesis process was significantly elevated by Ppy. Further investigation by metatranscriptomics revealed that fadE and fadN genes (to express the key enzymes in fatty acid metabolism) were highly expressed in the Ppy-driven AD, suggesting that Ppy promoted electron generation during acid production. For methanogenesis metabolism, genes related to acetate utilization and CO₂ utilization methanogenesis were also up-regulated by Ppy, illustrating that Ppy facilitates the utilization of acetate and electrons by methanogenic archaea, thus potentially promoting the methanogenesis through DIET.

Recent advances in aqueous virus removal technologies

The COVID-19 outbreak has triggered a massive research, but still urgent detection and treatment of this virus seems a public concern. The spread of viruses in aqueous environments underlined efficient virus treatment processes as a hot challenge. This review critically and comprehensively enables identifying and classifying advanced biochemical, membrane-based and disinfection processes for effective treatment of virus-contaminated water and wastewater. Understanding the functions of individual and combined/multi-stage processes in terms of manufacturing and economical parameters makes this contribution a different story from available review papers. Moreover, this review discusses challenges of combining biochemical, membrane and disinfection processes for synergistic treatment of viruses in order to reduce the dissemination of waterborne diseases. Certainly, the combination technologies are proactive in minimizing and restraining the outbreaks of the virus. It emphasizes the importance of health authorities to confront the outbreaks of unknown viruses in the future.

Unravelling the Methylene Blue Adsorption Mechanism on Doped and Nondoped Polyaniline: A Combined Molecular Modeling and Experimental Investigation

A multiscale investigation including computational chemistry calculations and experimental studies was performed to elucidate and understand the methylene blue (MB) adsorption on polyaniline (PANI) from an aqueous solution. Static DFT and DFT-based ab initio molecular dynamics were used to characterize the intermolecular interactions of this dye molecule with nondoped and doped PANI. Experimental adsorption studies at different operating conditions were performed to complement the mechanism analysis of this adsorption system. Infrared spectroscopy studies and ab initio calculations showed the important role of π-π stacking and van der Waals interactions for the dye adsorption on PANI. Experimental results of MB adsorption on the PANI surface indicated that alkaline conditions were more favorable than acidic conditions where the MB adsorption capacity ranged from 9.91 mg/g at pH 1.8 to 23.16 mg/g at pH 10.9. Equilibrium adsorption studies with nondoped PANI revealed a fast removal of the dye molecules where the equilibrium adsorption was reached after 45 minutes. The kinetic parameters were calculated with the pseudo-second and pseudo-first order models, while the adsorption mechanism was analyzed using the intraparticle diffusion, Boyd, and Elovich models. Dye adsorption equilibrium was studied at pH 8 and 30 °C where Temkin, Freundlich, Langmuir, and Dubinin-Radushkevich (D-R) isotherm models as well as a statistical physics monolayer model were employed in data analysis. The saturation dye adsorption capacity was 40.2 mg/g where an inclined adsorption orientation of dye molecules on the PANI surface could be expected with an adsorption energy of 14.0 kJ/mol. This interaction energy clearly indicated that only physical interactions were involved in the MB dye adsorption mechanism, which was also confirmed by the calculations with the D-R isotherm model. These theoretical and experimental results are important to understand the dye adsorption properties of conductive polymers and to consolidate their application in the synthesis of new adsorbents and composites for water treatment.

Polypyrrole supported Pd/Fe bimetallic nanoparticles with enhanced catalytic activity for simultaneous removal of 4-chlorophenol and Cr(VI)

Nanoscale zerovalent iron (nZVI) represents a promising reduction technology for water remediation, but its broad application is largely hampered by the tendency of nZVI to aggregate and the low electron transferability due to the interfacial charge resistance. Herein, by combining the advantages of polypyrrole (PPY) and nZVI, we prepared a composite material (i.e., PPY supported palladium‑iron bimetallic nanoparticles (Pd/Fe@PPY)) and applied it for the simultaneous removal of 4-chlorophenol (4-CP) and Cr(VI). Our results showed that this material had superior catalytic performances with a complete removal of 4-CP (50 mg·L^-1) and Cr(VI) (10 mg·L^-1) within 60 and 1 min, respectively. As opposed to the bare Pd/Fe nanoparticles, the reactivity of Pd/Fe@PPY with 4-CP was significantly enhanced by nearly 8 times. The enhanced catalytic activity of Pd/Fe@PPY was attributed to the distinctive properties of PPY as i) a good support that resulted in the formation of Pd/Fe nanoparticles with high dispersibility; ii) an adsorbent that increased the accessibility of 4-CP and Cr(VI) with electrons or active species (e.g., H*) on the particles surface; iii) an electron transfer carrier that facilitated the reactivity of Pd/Fe@PPY with contaminants by reducing the interfacial charge resistance. Moreover, by conducting cyclic voltammetry and quenching investigations, we showed that two mechanisms (i.e., direct and H*-mediated indirect electron transfer) were involved in the reductive dehalogenation of 4-CP, while catalytic hydrodechlorination played a dominant role. This work offers an alternative material for the efficient removal of 4-CP and Cr(VI) and provides better understanding of the relationship between structure and catalytic activity of nZVI.

Development of Nanocomposite Materials Based on Conductive Polymers for Using in Glucose Biosensor

Electropolymerized neutral red, thionine, and aniline were used as part of hybrid nanocomposite conductive polymers, to create an amperometric reagent-less biosensor for glucose determination. The structure of the obtained polymers was studied using infrared (IR) spectroscopy and scanning electron microscopy. Electrochemical characteristics were studied by cyclic voltammetry and impedance spectroscopy. It was shown that, from the point of view of both the rate of electron transfer to the electrode, and the rate of interaction with the active center of glucose oxidase (GOx), the most promising is a new nanocomposite based on poly(neutral red) (pNR) and thermally expanded graphite (TEG). The sensor based on the created nanocomposite material is characterized by a sensitivity of 1000 ± 200 nA × dm³/mmol; the lower limit of the determined glucose concentrations is 0.006 mmol/L. The glucose biosensor based on this nanocomposite was characterized by a high correlation (R² = 0.9828) with the results of determining the glucose content in human blood using the standard method. Statistical analysis did not reveal any deviations of the results obtained using this biosensor and the reference method. Therefore, the developed biosensor can be used as an alternative to the standard analysis method and as a prototype for creating sensitive and accurate glucometers, as well as biosensors to assess other metabolites.

Polypyrrole-based adsorbents for Cr(VI) ions remediation from aqueous solution: a review

Anthropogenic activities are principally responsible for the manifestation of toxic and carcinogenic hexavalent chromium (Cr(VI)) triggering water pollution that threatens the environment and human health. The World Health Organisation (WHO) restricts Cr(VI) ion concentration to 0.1 and 0.05 mg/L in inland surface water and drinking water, respectively. The available technologies for Cr(VI) ion removal from water were highlighted with an emphasis on the adsorption technology. Furthermore, the characteristics of several polypyrrole-based adsorbents were scrutinized including amino-containing compounds, biosorbents, graphene/graphene oxide, clay materials and many other additives with reported effective Cr(VI) ion uptake. This efficiency in Cr(VI) ions adsorption is attributed to enhanced redox properties, increased number of functional groups as well as the synergistic behaviour of the materials making up the composites. The Langmuir isotherm best described the adsorption processes with maximum adsorption capacities ranging from 3.40-961.50 mg/g. The regeneration of Cr(VI) ion-laden adsorbents was studied. Ion exchange, electrostatic attractions, complexation, chelation reactions with protonated sites and reduction were the mechanisms of adsorption. Nevertheless, there are limited details on comprehensive adsorbent regeneration studies to prolong robustness in adsorption-desorption cycles and utilization of the Cr(VI) ion-laden adsorbent in other areas of research to limit the threat of secondary pollution.

Biomechanical behaviour of PEDOT:PSS-based hydrogels as an electrode for stent integrated enzyme biofuel cells

The possibility of creating a biofuel cell based on a metal stent was shown in this study. Given the existing stent implantation approaches, the integration of a biofuel cell into a stent naturally entails capacity for biofuel cells to be installed into a human body. As a counter electrode, a hydrogel based on iota-carrageenan, polyvinyl alcohol, and PEDOT:PSS, with an immobilized glucose oxidase enzyme, was proposed. Tension tests demonstrated that the hydrogel mechanical behavior resembles that of a bovine's vein. To obtain an analytical description, the deformation curves were fitted using Gent and Ogden models, prompting the fitting parameters which can be useful in further investigations. During cyclic biaxial studies the samples strength was shown to decreases insignificantly in the first 50 cycles and, further, remains stable up to more than 100 cycles. The biofuel cell was designed with the PEDOT:PSS based material as an anode and a Co–Cr self-expanding stent as a cathode. The maximum biofuel cell power density with a glucose concentration of 5 mM was 7.87 × 10⁻⁵ W in phosphate buffer and 3.98 × 10⁻⁵ W in blood mimicking buffer. Thus, the biofuel cell integration in the self-expanding stent was demonstrated.

Highly antifouling polymer-nanoparticle-nanoparticle/polymer hybrid membranes

We introduce highly antifouling Polymer-Nanoparticle-Nanoparticle/Polymer (PNNP) hybrid membranes as multi-functional materials for versatile purification of wastewater. Nitrogen-rich polyethylenimine (PEI)-functionalized halloysite nanotube (HNT-SiO₂-PEI) nanoparticles were developed and embedded in polyvinyl chloride (PVC) membranes for protein and dye filtration. Bulk and surface characteristics of the resulting HNT-SiO₂-PEI nanocomposites were determined using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Moreover, microstructure and physicochemical properties of HNT-SiO₂-PEI/PVC membranes were investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM), and attenuated total reflectance (ATR)-FTIR. Results of these analyses indicated that the overall porosity and mean pore size of nanocomposite membranes were enhanced, but the surface roughness was reduced. Additionally, surface hydrophilicity and flexibility of the original PVC membranes were significantly improved by incorporating HNT-SiO₂-PEI nanoparticles. Based on pure water permeability and bovine serum albumin (BSA)/dye rejection tests, the highest nanoparticle-embedded membrane performance was observed at 2 weight percent (wt%) of HNT-SiO₂-PEI. The nanocomposite incorporation in the PVC membranes further improved its antifouling performance and flux recovery ratio (96.8%). Notably, dye separation performance increased up to 99.97%. Overall, hydrophobic PVC membranes were successfully modified by incorporating HNT-SiO₂-PEI nanomaterial and better-quality wastewater treatment performance was obtained.

Conductive-polymer-supported palladium-iron bimetallic nanocatalyst for simultaneous 4-chlorophenol and Cr(VI) removal: Enhanced interfacial electron transfer and mechanism

Nanoscale zerovalent iron (nZVI) reduction offers a wide range of applications in source-zone remediation, but the reactivity of nZVI is largely hampered due to its low electron-transfer ability and tendency to aggregate. Based on the dual function of conductive polymers (CPs) as support and electron transfer carrier, we combined CPs with nZVI and prepared a series of Pd/Fe bimetallic materials that successfully address the challenges of nZVI reduction. These Pd/Fe@CPs particles showed strong catalytic ability for the simultaneous removal of 4-chlorophenol (4-CP) and Cr(VI). The removal rate of 4-CP was significantly enhanced by 1.5-6.2 times after supporting Pd/Fe nanoparticles (NPs) with CPs. The enhanced reactivity of supported Pd/Fe NPs was attributed to their highly stabilized and dispersed state and the promoted electron transfer due to the synergistic effect between CPs and nZVI bimetallic particles. The various catalytic activity over Pd/Fe@CPs was attributed to the distinctive properties of CPs and their different interfacial electron transfer ability. Importantly, this study provides insights into distinguishing both mechanisms of direct electron transfer and atomic-hydrogen-mediated indirect electron transfer, and their quantitative relationship to the dehalogenation performance over Pd/Fe@CPs materials. This work provides better understanding of the remediation process and mechanisms of nZVI reduction.

Green products from herbal medicine wastes by subcritical water treatment

Herbal medicine wastes (HMWs) are byproducts of medicine factories, which are mainly landfilled for their environmental problems. Only bearing in mind the contamination and concerns caused by the COVID-19 pandemic and environmental emissions, the worth of herbal medicine wastes management and conversion to green products can be understood. In this work, subcritical water treatment was carried out batch-wise in a stainless tube reactor in the pressure range of 0.792-30.0 MPa, varying the temperature (127-327 °C) and time (1-60 min) of extraction. This resulted in new and green material sources, including organic acids, amino acids, and sugars. Amazingly, at very low extraction times (below 5 min) and high temperatures (above 277 °C), about 99% of HMWs were efficaciously converted to clean products by subcritical hydrothermal treatment. The results of hydrothermal extraction after 5 min indicated that at low temperatures (127-227 °C), the total organic carbon in the aqueous phase increased as the residual solid phase decreased, reaching a peak around 220 °C. Acetone soluble extracts or fat phase appeared above 227 °C and reached a maximum yield of 21% at 357 °C. Aspartic acid, threonine, and glycine were the primary amino acids; glycolic acid, formic acid, lactic acid, and acetic acid were obtained as the main organic acids, glucose, fructose, and cellobiose were substantial sugars produced from the aqueous phase after 5 min of hydrothermal subcritical hydrolysis extraction.

Doped-polyaniline based sorbents for the simultaneous removal of heavy metals and dyes from water: Unravelling the role of synthesis method and doping agent

Recently, the engineering of alternative adsorbents with better functional and sorbing ability towards the purification of wastewaters has received much attention from the scientific community. Currently polymers, in particular, are regarded as attractive soft materials in the field of environmental remediation due to their several unique properties. In this regard, the synthesis method is key point to fabricate polymer-based adsorbent with targeted characteristics. In the present work, four polyaniline (PANIs) samples were synthesized by two alternative chemical approaches, a traditional one and an eco-friendly one, and two different dopants were used, HCl and H₂SO_4, respectively. All PANIs were characterized for their thermal, optical, morphological, and structural properties and their capability to remove simultaneously dyes and heavy metals from water have been investigated. It was deduced that the sorption ability is dependent on the as-synthesized PANI using different procedures and dopants. All the PANIs from traditional method showed high levels of pollutants removal (from 89 to 97%). Even though the materials obtained from the green way are overall less active, H₂SO₄-doped corresponding polymer showed high sorption capability (75-97%). Finally, the most performing PANIs were selected for recycling tests exhibiting high sorption efficiency retention up to four runs without any regeneration treatment. Most important, the cycling tests were stopped well before the sample sorption limit could be reached.

Crystalline polysaccharides: A review

The biodegradability and mechanical properties of polysaccharides are dependent on their architecture (linear or branched) as well as their crystallinity (size of crystals and crystallinity percent). The amount of crystalline zones in the polysaccharide significantly governs their ultimate properties and applications (from packaging to biomedicine). Although synthesis, characterization, and properties of polysaccharides have been the subject of several review papers, the effects of crystallization kinetics and crystalline domains on the properties and application have not been comprehensively addressed. This review places focus on different aspects of crystallization of polysaccharides as well as applications of crystalline polysaccharides. Crystallization of cellulose, chitin, chitosan, and starch, as the main members of this family, were discussed. Then, application of the aforementioned crystalline polysaccharides and nano-polysaccharides as well as their physical and chemical interactions were overviewed. This review attempts to provide a complete picture of crystallization-property relationship in polysaccharides.

Conductive Polymers and Their Nanocomposites as Adsorbents in Environmental Applications

Proper treatment and disposal of industrial pollutants of all kinds are a global issue that presents significant techno-economical challenges. The presence of pollutants such as heavy metal ions (HMIs) and organic dyes (ODs) in wastewater is considered a significant problem owing to their carcinogenic and toxic nature. Additionally, industrial gaseous pollutants (GPs) are considered to be harmful to human health and may cause various environmental issues such as global warming, acid rain, smog and air pollution, etc. Conductive polymer-based nanomaterials have gained significant interest in recent years, compared with ceramics and metal-based nanomaterials. The objective of this review is to provide detailed insights into different conductive polymers (CPs) and their nanocomposites that are used as adsorbents for environmental remediation applications. The dominant types of CPs that are being used as adsorbent materials include polyaniline (PANI), polypyrrole (Ppy), and polythiophene (PTh). The various adsorption mechanisms proposed for the removal of ODs, HMIs, and other GPs by the different CPs are presented, together with their maximum adsorption capacities, experimental conditions, adsorption, and kinetic models reported.

Investigating the hexavalent chromium removal from aqueous solution applying bee carcasses and corpses modified with Polyaniline

There are currently heavy metals in most industrial effluents which are among the most significant environmental pollutants. Hexavalent chromium is one of the most significant heavy metals. In this research for the first time, eliminating the hexavalent chromium from the aqueous medium/aquedia applying bee carcasses and corpses modified with polyethylene was examined. Adsorption experiments were conducted discontinuously on laboratory solutions, including hexavalent chromium. The optimal adsorption conditions such as different pH factors, contact time, initial chromium concentration, and adsorbent value on the adsorption rate were examined at different levels, and adsorption isotherms were plotted. Some adsorbent properties were examined using Field Emission Scanning Electron Microscopy, XRD analysis, Fourier Transform Infrared Spectroscopy, and BET test to study the properties of the synthesized adsorbent. This study indicated that the highest percentage of removal related to polyethylene composite and bee carcasses in the presence of polyethylene glycol was 50.56% among the bee carcasses composites. The parameters effective on the adsorption process for polyethylene composite and bee carcasses and losses in the presence of polyethylene glycol suggested that the adsorption percentage increased for this composite by decreasing the pH, increasing the contact time, and increasing the adsorbent. The highest percentage of adsorption was obtained when the pH was 2, the contact time was 120 min and the adsorbent value was 8 g/L and the initial concentration of chromium was 100 ppm. The most optimal removal percentage was achieved at the pH = 2, the contact time was 30 min, and the adsorbent value was 2 g/L, and the initial chromium concentration was 100 ppm. The results of drawing adsorption isotherms also indicated that higher R2 had a better fit than Langmuir for polyethylene composite and bee carcasses in the polyethylene glycol Freundlich equation.

Recent progress in green and biopolymer based photocatalysts for the abatement of aquatic pollutants

Enormous research studies on the abatement of anthropogenic aquatic pollutants including organic dyes, pesticides, cosmetics, antibiotics and inorganic species by using varieties of semiconductor photocatalysts have been reported in recent decades. Besides, many of these photocatalysts suffer in real applications owing to their high production cost and low stability. In many cases, the photocatalysts themselves are being considered as secondary pollutants. To eliminate these drawbacks, the green synthesized photocatalysts and the use of biopolymers as photocatalyst supports are considered in recent years. In this context, recent developments in green synthesized metals, metal oxides, other metal compounds, and carbon based photocatalysts in water purification are critically reviewed. Furthermore, the pivotal role of biopolymers including chitin, chitosan, cellulose, natural gum, hydroxyapatite, alginate in photocatalytic removal of aquatic pollutants is comprehensively reviewed. The presence of functional groups, electron trapping ability, biocompatibility, natural occurrence, and low production cost are the major reasons for using biopolymers in photocatalysis. Finally, the summary and conclusion are presented along with existing challenges in this research area.

Crack pathway analysis in graphene-like BC3 nanosheets: Towards a deeper understanding

Carbon based two-dimensional (2D) nanostructures have exceptional mechanical properties. Analysis of crack pathway in 2D graphenic materials allows for developing crack arrestors. Herein, we serve Molecular Dynamics (MD) to simulate the fracture behavior of 2D graphene-like boron-carbide (BC₃) by manipulating the crack length (10, 20, 30, 40, and 50 Å) and the crack arrestor (circular and square). Young's modulus, the failure stress, failure strain, and fracture toughness of theoretically born BC₃ nanosheets were then captured. The crack arrestors were studied in three different states (constant position, as well as 4 and 6 Å from crack tips). Three factors, i.e. the stress, crack length, and geometry of nanosheets determined crack pathway considering zigzag and armchair directions. Overall, circular arrestors more severely affected the fracture toughness, failure stress and failure strain with respect to square ones; while Young's modulus variation followed an inverse trend. Moreover, the highest Young's modulus was detected for cracks having length of 10 Å. Fracture toughness increased upon increasing the crack length. In conclusion, the crack arrestors were promising for tuning the mechanical properties of 2D nanosheets.

Chitosan-based blends for biomedical applications

Polysaccharides are the most abundant naturally available carbohydrate polymers; composed of monosaccharide units covalently connected together. Chitosan is the most widely used polysaccharides because of its exceptional biocompatibility, mucoadhesion, and chemical versatility. However, it suffers from a few drawbacks, e.g. poor mechanical properties and antibacterial activity for biomedical applications. Blending chitosan with natural or synthetic polymers may not merely improve its physicochemical and mechanical properties, but may also improve its bioactivity-induced properties. This review paper summarizes progress in chitosan blends with biodegradable polymers and polysaccharides and their biomedical applications. Blends of chitosan with alginate, starch, cellulose, pectin and dextran and their applications were particularly addressed. The critical and challenging aspects as well as the future ahead of the use of chitosan-based blends were eventually enlightened.